b series control panel installer quick start guide...you can also scan in the qr code. navigate to...
TRANSCRIPT
Location Item Description Specifi cation
A MODULE 1Plug-in comm
moduleCommunication module options
B ETHERNET Ethernet port built-in on-board Ethernet connection (10Base-T/100Base-T)
C USB USB port USB connector (for fi rmware updates and RPS connection)
D Heartbeat LED Slow=normal, rapid=service mode
E Reset Reset switch Hold fi ve seconds to enter or exit service mode
F B C Outputs B(2) C(3) Open collector, 50mA, active low
G TMPR Tamper Optional Tamper Switch Connector
H1 COM 2 to
7 COM 8Alarm inputs 1k Ω EOL
I R Y G B SDI2 bus SDI2 device bus
J COM AUX Aux power 12 VDC, 800mA
K NO C NC Output A(1) Programmable relay output
L+ BAT –
18 VAC, Battery, Earth
ground, 18 VACPrimary/Secondary power and Earth Ground connections
M Mounting Mounting holes Mounting holes for Control panel
Control panel connection location
B Series Control PanelInstaller Quick Start Guide
Use this guide to quickly install a B6512/B5512/B4512/B3512 Bosch security system. Additional information is found in the Control Panel Installation & System Reference Guide.
For Additional Training:
B Series Overview:
B Series Micro site:
Bosch YouTube Channel:
When you see this icon; use your smart phone with a QR code reader app to view helpful videos.
A
B
CDE
F
G
HIJKL
M
Control panel component layout
R
Y
G
B
7 COM 8
COUTPUT
B
1 k End of Line Resistors
Voltage RangesON-BOARD POINTS
3.7 - 5.0 VDC2.0 - 3.0 VDC0.0 - 1.3 VDC
Open Normal Short
3 COM 4 5 COM 61 COM 2
R Y G B
SDI2Device Bus
AUX- 12 V + TM
PR
1 COM 2 7 COM 83 COM 4 5 COM 6
RES
ET
COM AUX R Y G BPWR A B COM
B
C
OU
TPU
T
RYGB
Step 1 Mounting the control panel
• Mount the enclosure prior to mounting the control panel.• Mount control panel into enclosure with hardware provided.
Bosch Tips:
B10
B11
Step 4 Installing expansion modules
Bosch Tips:
MM
II
Step 7 Powering the control panel
Bosch Tips:
LL
Bosch Tips:• Insert leg of module into slot marked “x.”• Cellular: Place antenna on top of enclosure
and run cable inside, then connect to module.
• PSTN: Connect module to a D166 (RJ31x) jack using a D161/D162 cable.
Step 2 Installing a communication module AA Step 3 Installing a keypad
Bosch Tips:
II
• If installing a B942 or B915, refer to keypad installation guide for wiring diagrams.
• If installing more than one keypad, refer to keypad installation guide for unique address settings.
RYGB
7 COM 8
COUTPUT
B
1 k End of Line Resistors
Voltage RangesON-BOARD POINTS
3.7 - 5.0 VDC2.0 - 3.0 VDC0.0 - 1.3 VDC
Open Normal Short
3 COM 4 5 COM 61 COM 2
R Y G B
SDI2Device Bus
AUX- 12 V + TM
PR
1 COM 2 7 COM 83 COM 4 5 COM 6COM AUX R Y G BPWR A B COM
B
C
OU
TPU
T
• If installing more than one device that is similar, refer to the modules installation guide for address settings (for example, two of the same device).
• If installing a RADION B810 wireless receiver, use address 1 only.
Step 6 Installing a bell or siren
Bosch Tips:
Step 5 Installing wired inputs HH
• If using a dual EOL, 2K EOL, or No EOL, refer to control panel installation guide for control panel settings.
• If using 2-wired powered devices, use a B201 or D125B.
Bosch Tips:
NOEOL
NC
7 COM 8
COUTPUT
B
1 k End of Line Resistors
Voltage RangesON-BOARD POINTS
3.7 - 5.0 VDC2.0 - 3.0 VDC0.0 - 1.3 VDC
Open Normal Short
3 COM 4 5 COM 61 COM 2
R Y G B
SDI2Device Bus
AUX- 12 V + TM
PR
1 COM 2 7 COM 83 COM 4 5 COM 6
RES
ET
COM AUX R Y G BPWR A B COM
B
C
OU
TPU
T
KKJJ
• Connect wires to control panel before applying battery or AC power.• Connect Earth Ground to a cold water pipe (copper) or other solid
connection to ground.
LocationLocation LocationLocation LocationLocation
LocationLocation LocationLocation LocationLocation
LocationLocation
Plug-in modules(B430/B44x)
B201 PowerLoop module
• Output A can supply up to 1 amp at 12 VDC when sourced from a control panel (Jumper in AUX PWR position).
• Output A can support up to 3 amps at 12 VDC when using a separate power supply (Jumper in DRY position).
• Output B and C are open collector and are limited to 50 mA at 12 VDC.
+
Step 8 Creating control panel accounts
Keypadprogramming
• Follow Account Assistant instructions within RPS v6.03 or later to create control panel accounts.
• If RPS is not available, Keypad Programming is an option. Refer to Installation Instructions.
Battery
Step 9 Connecting the control panel
Bosch Tips:
BBLocationLocation
RPS/USB connection
TMPR
7 COM 8
RES
ETET
HER
NET
B
C
OU
TPU
T
7 COM 8
COUTPUT
B
USB
ETHERNET100BASE-T
LINK Or
• Connect a computer with Remote Programming Software (RPS) installed. Connecting to RPS can be done through the use of a USB or Ethernet connection.
• Launch RPS 6.03 or greater. The Account Assistant automatically launches when you create a new account.
• For USB direct connect use a B99 USB cable.
CC
RPS/IP Direct connectionthrough Onboard Ethernet
B Series Wiring Basics:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
B Series Control PanelInstaller Quick Start Guide
© 2017 Bosch Security Systems, Inc. F.01U.324.620 | 02 | 2017.01
• Perform a Walk Test.• Send a test report
After system installation and control panel programming, perform a complete system test. A complete system test includes testing the control panel, all devices, and communication destinations for proper operation.
FAQs
Step 12
Bosch Tips:
Disconnect from RPS and test the system
Step 10
Bosch Tips:
• Press Send from the Account Assistant when program is ready.
Send program to control panel
Step 11
Bosch Tips:
Entering Classic Mode in RPS
• Switch to Classic Mode if your system requires further programming such as using multiple areas. After programming changes, repeat step 10.
Test Menu
Notification Test
Revisions
Test Report
Walk Test
• Press Disconnect from control panel when programming is complete.
B520 AUX Power Supply CX4010* 18VAC Transformer
TR1850* 18VAC Transformer
B450 Remote Cellular Interface
RFBT Billtrap Transmitter
RFDL–11 PIR Microwave TriTech35 x 25 ft.
RFPR–12 PIR, Pet Immune 40 ft.
RFDW–RM Recessed Door/Window Contact
RFDW–SM Surface Mount Door/Window Contact
RFGBGlass Break Detector
RFUNUniversal Transmitter w/ Door/Window Contact
RFSM Wireless Smoke Detector
RFPR–C12Curtain PIR, Pet Immune 40 x 5 ft.
RFPB–SBRFPB–TB1 & 2 Button Panic
RFKF–TBSRFKF–FBS2 & 4 Button Keyfobs
RADION Wireless Devices
Power Communicators
RFID Tags for Readers & B942 KepadsACA–ATR13 ACD–ATR14CSACD–ATR11ISO
B810 SDI2 Wireless Receiver RFRP Wireless Repeater
IP Camera Integration
Any Bosch IP camera
D1218 18Ah Battery
D135A Low-Battery Disconnect Module
DS9370/DS9371360TriTech 70 ft.
ISC–BDL2–WP12G/WP6G/W12G TriTech40 X 40 ft./20 x 20 ft./ 40 x 40 ft.
Classic Series
B430 Telephone (PSTN)
D192G Bell Super Vision Module
D125B Dual Class B Initiating Module
B201 2–wire powered loop
F220/F220–B6RSmoke Detector plus Base
D132A Reversing Relay
Residential Fire
B56 Keypad Backbox
Enclosures & Accessories
D137 Mounting Bracket
D138 Mounting BracketRight Angle
ICP–EZTS Universal Tamper
B10 Medium Enclosure
B11 Small Enclosure
B208 Octo-Input Module
B308 Octo-Output Module
I/O Expansion Modules
ISC–CDL1–W15xTriTech50 ft.
Wired Motion Detectors
Commercial Series
Blue Line Gen2 Series
*Country Specifi c variants will apply
B440–C Cellular (Verizon 3G CDMA)
B441–C Cellular (Verizon CDMA)
B443 Cellular (HSPA+ SIM Required)
D5500CURPS Upgrade
Programing and Software
Remote Security Control Mobile App
B99 USB Cable
*Automation
Remote Security Plus Mobile App
G100 Z-Wave Home Control Gateway
Inovonics Wireless Devices
EN4200 Serial Receiver
B820 Wireless Interface
D126 7Ah Battery
B930 Text w/ Soft Keys
B920 Text w/ Function Keys
Keypads
B915 Text B921C Capacitive Touch
B942 Touch Screen B942W Touch Screen
What is my default code?User Code: 123456Installer Code: 123
How do I use Output B and C?Outputs B and C are Open Collector Outputs. Wiring can be found in control panel installation manual, section heading Open Collector Outputs.
How do you remotely turn on and turn off the control panel?This can be done through the use of the Remote Security Control App (RSC).
How do I connect directly to the control panel with Ethernet?By default, the control panel is set up to auto detect and negotiate a connection to RPS when an ethernet cable is connected between them.
What do I need to be able to send personal notifi cations?SMS (Text) messages require the use of a cellular module and emails can be sent by either an Ethernet or Cellular connection. How do I enter “Service Mode”?Press and hold the yellow reset button on the control panel for 5 seconds (repeat to exit).
Control panel
Access Modules(B6512 only)B901Access Module
B Series Control Panel Accessories (partial list)
Where can I go for additional help?
For additional help, tips and other useful information, visit the Security Knowledge Base link on our website.Go to: http://us.boschsecurity.comYou can also scan in the QR code.Navigate to the Knowledge Base link as shown in the adjacent illustration.
(B942 is keypad shown)
D101 Lock and Key set
us.boschsecurity.com
ISC–CDL1–WA15xTriTech+ w/Anti-Mask50 ft.
Note: Not all products and features are available in all regions. Consult your Bosch representative or product datasheets for details.
*Home automation may not be available in all regions. Consult your Bosch representative for details.
-A versions of RADION devices are used in North and South America. Non -A versions are used in Europe, Africa, and Australia.
B442 Cellular (GPRS SIM Required)