avermedia averdigi eb1304net sata sata manual.pdfa: averdigi eb1304net sata unit b: averdigi...

AVerMedia® AVerDiGi

EB1304NET SATA EB1304NET SATA+

User Manual

Nov. 2009

FCC NOTICE (Class A) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

.Federal Communications Commission Statement NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help.

Class A ITE Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use: Warning --This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. European Community Compliance Statement (Class A)

This product is herewith confirmed to comply with the requirements set out in the Council Directives on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive 2004/108/EEC.

Warning - This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct this interference.

DISCLAIMER No warranty or representation, either expressed or implied, is made with respect to the contents of this documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information presented in this documentation has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information contained in this documentation is subject to change without notice. In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages. TRADEMARKS AVerMedia, being authorized AVerMedia Information, Inc. to use, is registered trademarks of AVerMedia TECHNOLOGIES, Inc. IBM PC is a registered trademark of International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc. Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation. All other products or corporate names mentioned in this documentation are for identification and explanation purposes only, and may be trademarks or registered trademarks of their respective owners.

COPYRIGHT © 2009 by AVerMedia INFORMATION, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of AVerMedia TECHNOLOGIES, Inc.

The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your other household waste. Instead, you need to dispose of the waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. For more information about where to drop off your waste equipment for recycling, please contact your household waste disposal service or the shop where you purchased the product.

Battery Safety Information - Store the batteries in a cool dry place. - Do not dispose of used batteries in domestic waste. Dispose of batteries at special collection points or return to

point of sale if applies. - Remove the batteries during long periods of non-use. Always remove exhausted batteries from the remote

control. Battery leakage and corrosion can damage this remote control, dispose of batteries safely. - Do not mix old and new batteries. - Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). - Do not dispose of batteries in a fire. The batteries may explode or leak. - Never short circuit the battery terminals.

WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

CAUTION IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION

NOTICE - INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT

NOTICE. - THE INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR

REFERENCT ONLY.

LIGHTNING WARNING − TO AVOID THE LIGHTNING STRIKE, STRONGLY SUGGEST INSTALLING

THE LIGHTNING ROD AT LIGHTNING FREQUENTLY AREA. − FOR ADDED PROTECTION, UNPLUG THE DVR UNIT DURING THE

LIGHTNING STORM. THIS MAY PREVENT TO DAMAGE THE DVR UNIT DUE TO THE LIGHTNING.

Table of Contents

Chapter 1 Introduction ................................................................................ 1 1.1 Package Content .................................................................................................. 1 1.2 Features and Specifications ................................................................................. 1 1.3 Front Panel ........................................................................................................... 3

1.3.1 EB1304NET SATA ........................................................................................... 3 1.3.2 EB1304NET SATA+ .......................................................................................... 3

1.4 Back Panel ........................................................................................................... 5 1.5 Setting Up the DVR Unit ....................................................................................... 6

1.5.1 Installing the Hard Disk .................................................................................... 6 1.5.2 Adjust Fan Speed ............................................................................................. 7 1.5.3 Connecting Devices ......................................................................................... 8 1.5.4 Connecting the Sensor device/Relay device /PTZ Camera ............................. 9

1.5.4.1 Sensor and Relay Pin Definition ................................................................... 9 1.5.4.2 RS-485 Pin Definition ................................................................................. 10

Chapter 2 Operating the DVR unit ............................................................ 11 2.1 Familiarizing the Buttons of Remote Control ....................................................... 11

2.1.1 Using AB Repeat Function ............................................................................. 12 2.1.2 Using USB Backup Button ............................................................................. 13 2.1.3 Controlling PTZ Camera ................................................................................ 13

2.1.3.1 To Enter the PTZ Mode .............................................................................. 13 2.1.3.2 To Set Preset Position ................................................................................ 14 2.1.3.3 To Control PTZ Camera ............................................................................. 14

2.2 Using the DVR for the First Time ........................................................................ 14 2.2.1 Set up the System Date and Time ................................................................. 15

2.3 Surveillance Screen ........................................................................................... 15 2.4 Playback the Video ............................................................................................. 17

Chapter 3 OSD Navigation Tree ............................................................... 18 3.1 Menu Function .................................................................................................... 19

Chapter 4 Using the USB Playback Console .......................................... 30 4.1 Recommended system requirements ................................................................. 30 4.2 Installing the USB Playback Console ................................................................. 30 4.3 Running the USB Playback Console .................................................................. 31

4.3.1 To Cut and Save the Portion of the Recorded Video ...................................... 33 4.3.2 Playback DVR Recorded File from Hard Disk ................................................ 33 4.3.3 Playback Backup File(*.dvr) ........................................................................... 34 4.3.4 Playback Backup File (*.avf) .......................................................................... 34

Chapter 5 Backup Recorded Video File .................................................. 35 5.1 Familiarizing with HDD Backup Application ........................................................ 35

5.2 To Backup Recorded Video File ......................................................................... 36 Chapter 6 ImageVerification ..................................................................... 37

6.1 To Run the ImageVerification .............................................................................. 37 Chapter 7 iEnhance ................................................................................... 38

7.1 To Use iStable .................................................................................................... 39 Chapter 8 Using the Remote Programs .................................................. 40

8.1 Familiarizing the Web Viewer Buttons ................................................................ 41 8.1.1 To Setup Remote System Setting .................................................................. 43

8.1.1.1 System Setup ............................................................................................. 43 8.1.1.2 Camera Setup ............................................................................................ 44 8.1.1.3 Record Setup ............................................................................................. 45 8.1.1.4 Alarm/Sensor Setup ................................................................................... 47 8.1.1.5 Network Setup ............................................................................................ 49 8.1.1.6 Password Change ...................................................................................... 51

8.2 Familiarizing the Remote Console Buttons ......................................................... 52 To Setup Remote Console Setting ............................................................................. 53

8.3 Using the Remote Playback ............................................................................... 54 8.3.1 Familiarizing the Local Playback Buttons ....................................................... 55 8.3.2 Familiarizing the Download and Playback Buttons ........................................ 57

8.3.2.1 To Cut and Save the Wanted Portion of the Recorded Video ..................... 58 8.3.2.2 To Search Using the Visual Search ............................................................ 58 8.3.2.3 To Search Using the Intelligent Search ...................................................... 59

Chapter 9 Using HandyViewer to Access DVR server ........................... 60 9.1 Using PDA Viewer to Access DVR Server .......................................................... 60

9.1.1 To install PDAViewer thru ActiveSync ............................................................ 60 9.1.2 To install PDAViewer from the Internet ........................................................... 61 9.1.3 To Use the PDAViewer ................................................................................... 62 9.1.4 To Playback in PDA Viewer ............................................................................ 63

9.2 Using JavaViewer to Access DVR Server .......................................................... 64 9.2.1 To Use the JAVAViewer .................................................................................. 65

Appendix A Registering Domain Name ...................................................................... 66 Appendix B Network Service Port .............................................................................. 67

1

Chapter 1 Introduction 1.1 Package Content

A B

(2)

AVerMedia

AVerDiGi EB1304NET SATA

®Quick Installation Guide

(3)

(1)

(4)

(5)

(6)

(7)

(1) DVR Unit

A: AVerDiGi EB1304NET SATA unit B: AVerDiGi EB1304NET SATA+ unit

i

The model of DVR unit is depending on your purchase.

(2) Remote Control (batteries included) (3) Quick Installation Guide (4) Power Cord

* The power cord varies depending on the standard power outlet of the country where it is sold.

(5) Power Adapter (6) Internal HDD holder (8 screws are included) (7) Software CD (User Manual included)

1.2 Features and Specifications Key Features

- Lightweight and Compact size (1/5 of general DVR net weight) - Multi-functional front panel design (only for EB1304NET SATA+) - Thermal testing verification approved - Heat-resistance material - Supports standard 3.5” SATA HDD - Embedded Linux and RTOS - MPEG4 video compression - JavaViewer on mobile phone - Supports PTZ control

2

- Supports UPnP (Universal plug and play) - Remote Software Integration: CM3000, Remote Console, WebViewer, PDAViewer,

HandyViewer, and SmartViewer ( for Symbian / Windows Smart phone) - Non-PC stand-alone network digital video recorder - On Screen Display(OSD) control menu

Video Feature - 4 composite video inputs (BNC connector) - 1 Composite & 1 VGA outputs - Video compression: MPEG4 - Video Format: NTSC and PAL - 1 channel audio input/output - Display resolution:720 x 480/720 x 576 (NTSC/PAL) - Display frame rate:Total 120/100 fps (NTSC/PAL) - Hue/Brightness/contrast/Saturation adjustable

Recording resolution: - Full D1: 720 x 480/720 x 576 (NTSC/PAL) - CIF: 360 x 240/360 x288 (NTSC/PAL)

Recording frame rate: - Full D1: 60/50 fps (NTSC/PAL) - CIF: 120/100 fps (NTSC/PAL)

Recording mode: - Schedule recording (00:00~24:00 set by hour) - Continuous /Motion / Sensor recording - Auto recycle recording - Auto record enabling

Remote access - Support CMS (CM3000)

i

If you need CMS application, please contact your local sales dealer for forwarder information.

- Support PDAViewer - Support Remote Console & WebViewer - Password authentication mechanism

Playback Mode - Video search by date/time/event - Infinite event list for easy search - A-B video repeat playback - Free Playback Application Software: - Playback from pen drive/ external HDDx1 - Playback and backup on any PC with Windows 2000/XP/Vista - Converting files to AVI format enabling to playback on Windows Media Player - Video segment selectable for repeating payback and backup - Enabling quick HDD to HDD backup - Watermark function for image verification

I/O - 4 Sensor inputs - 1 Relay output controlling alarm, lock, light, or other devices - Operating Temperature: 5~40 degree

3

1.3 Front Panel 1.3.1 EB1304NET SATA

Name Function

(1) DVR Power LED Light when the unit is power on

(2) HDD LED Indicate the hard disk running state. Light when the HDD is running (Read/Write)

(3) IR Sensor Receive signal from the remote control to operate the unit

(4) IR Sensor Port To connect extended IR sensor cable

(5) USB 2.0 Port Connect to pen drive / external hard disk for backup

i

If the external hard disk is first time using, please format to FAT32 format.

1.3.2 EB1304NET SATA+

(1)(2)(3) (4) (5) (7) (8) (9)

(10)

(6)

Name Function

(1) DVR Power LED Light when the unit is power on

(2) HDD LED Indicate the hard disk running state. Light when the HDD is running (Read/Write)

(3) IR Sensor Receive signal from the remote control to operate the unit

(4) IR Sensor Port To connect extended IR sensor cable

(5) USB 2.0 Port Connect to pen drive / external hard disk for backup

i

If the external hard disk is first time using, please format to FAT32 format.

4

Name Function (6) 1/2/3/4/Quad

Use these buttons in playback mode to switch to display each channel in full screen or view all channels at the same time Use the buttons in setting password of OSD menu to:

For ”1”

For “2”

For “3”

For “4”

For “0”

(7) Record REC Start video recording. To stop recording, press

(8) Menu Call up and exit the OSD main and sub menu

(9) UP/DOWN/SELECT

Use the UP and DOWN buttons to change setting and move to the left and right, and SELECT to enter or make a selection

(10) Playback/OSD Menu Control Buttons

Use the buttons in playback mode to:

Display the play list and play the recorded video

Wind back the video playback at the speed of 2x, 4x, 8x or 16x

Fast play the video playback at the speed of 2x, 4x, 8x or 16x

Temporarily freeze the video playback

Stop video playback

Use the buttons in navigating OSD menu to :

Move to the left and right

Change the setting

Make a selection

5

1.4 Back Panel

Name Function

(1) RJ-45 port : Ethernet connection port

(2) CH1/CH2/CH3/CH4 : Input the video camera signal and display it on channel 1/2/3/4

(3) TV Out : Output the video signal to other video output device through BNC port

The DVR unit support 2 video output ports and you can only select to output the video either from the VGA OUT or VIDEO OUT

(4) VGA OUT : Output the video signal to a CRT or LCD monitor

(5) Audio Out/In : - Input the audio signal from audio output device which it has a power supply by itself. The audio is embedded with channel 1

- Output the audio signal to a audio out device which it has a power supply by itself

i

The DVR doesn’t supply the power to external audio in/out devices.

(6) Sensor In & Alarm

Out : Support up to 4 sensor device and 1 relay device (Relay: 1A @ 125V

AC/30V DC)

(7) RS485 For PTZ camera connection

(8) TV-VGA Switch : Switch to select the video output. Make sure to set the video output before turning on the unit

(9) 12V DC : Connect the power adapter into this port

6

1.5 Setting Up the DVR Unit 1.5.1 Installing the Hard Disk The DVR unit allows user to install one SATA hard disk.

i

For hard disk spec, please referring to http://www.avermedia.com/AVerDiGi/ → Products → Embedded Analog DVR → AVerDiGi EB1304NET SATA series → Hardware Recommendations

The “compatible hard disks” indicated in the above recommendation list only means that these commercially available hard disks were tested with AVerMedia products and functioned well under normal operation conditions. AVerMedia does not guarantee or provide warranties, explicitly, implied or statutory with respect to the reliability of the hard disk function or its compatibility. In no event AVerMedia shall be liable for damages, with respect to any business interruption of clients, lost profits, loss of programs or other data on your information handling system or otherwise. This includes direct, indirect, incidental, special, or consequential damages, resulting from the incompatibility caused by the usage of these hard disks, even if AVerMedia has expressly advised about the risk of such damages. The entire risk arising out of the use of any information attached here with is borne by the recipient.

Follow the illustrated instructions below to install the hard disk:

1. Loosen all screws 2. Push the cover backward and lift

3. Secure the brackets on the hard disk

4. Connect the the SATA cable and the power connector to the hard disk

7

5. Secure the hard disk inside the unit then replace unit cover

6. Push the cover forward and secure the cover

7. You may now connect all the cables. When the power is connected, the Power LED light turns on

1.5.2 Adjust Fan Speed The DVR provides 3 speed of fan for user to adjust by actual condition. 1. Loosen all screws

2. Push the cover backward and lift

3. Move the pin cover to the pin. 3x is maximum, 2x is medium and 1x is low.

4. Push the cover forward and secure the cover after adjust the fan speed.

8

1.5.3 Connecting Devices The back panel of the DVR unit, user can connect up to 4 video cameras, 4 sensor devices, 1 alarm device and output video to a TV or CRT/LCD monitor. Connecting the unit to a pen drive or external hard disk through USB interface for backup, then use the bundled software enables user to transfer, playback and segment the video. Follow the illustration below to make the connection:

Each time you change the video display output or video system (NTSC/PAL), the power must be turned off and on to reset the DVR unit.

9

1.5.4 Connecting the Sensor device/Relay device /PTZ Camera The Audio, Sensor, Alarm, and RS485 port enable you to connect 1 audio input device, 1 audio output, 4 sensor inputs, 1 relay outputs, and PTZ camera. Just connect the external audio input/output device, sensor, relay, and PTZ camera pin directly to the pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay output.

The signal from the sensor (i.e., infrared sensors, smoke detectors, proximity sensors, door sensors, etc.) is being transmitted to the unit and this triggers the system to respond and send signal to relay device (i.e., alarm, telephone etc).

1.5.4.1 Audio in and out pinhole: Pin # Definition 1 Audio input signal 2 Audio input signal 3 Audio output signal 4 Audio output signal

1.5.4.2 Sensor and Relay Pin Definition

Pin # Definition

5 Sensor 1 signal

6 Sensor 1 Ground signal

7 Sensor 2 signal


9 Sensor 3 signal


11 Sensor 4 signal


13 Relay signal

14 Relay signal

10

1.5.4.3 RS-485 Pin Definition When connect PTZ camera through RS485 interface, please refer to the following pin definition to connect the DVR and PTZ.

Pin # DVR site PTZ site 15 TX+ RS485 TX+ signal RS485 RX+ signal 16 TX- RS485 TX- signal RS485 RX- signal 17 RX+ RS485 RX+ signal RS485 TX+ signal 18 RX- RS485 RX- signal RS485 TX- signal

i

If user uses the 2 wires for the PTZ camera connection, please connect to the RS-485 TX+ and TX- of the DVR site.

11

Chapter 2 Operating the DVR unit 2.1 Familiarizing the Buttons of Remote Control Use the Remote control to operate the OSD menu on surveillance screen.

Button Function

(1) FN A functional key for multiple DVR system remote control

(2) 1Switch to Channel 1 As a number key for entering password



(5) 9Switch to Channel 4

As a number key for entering password

(6) 5Switch to QUAD mode


Button Function

(7)

2


4

6

8

0

(8) A-B Set a playing recorded video from A point to B point segment and repeat playing on surveillance screen(See 2.1.1)

(9) Pause the playing

(10)

▲

To play the video

(11) ▼▼ Decrease the video playback at the speed of 2x, 4x, 8x or 16x

(12) ▼ ▼ Fast play the video playback at the speed of 2x, 4x, 8x or 16x

(13) Stop playing / Stop recording

12

(14) USB backup(see 2.1.2)

Button Function

(15)

▼ To move the selection to the left and right ▼

▲ To go up and down and select the items in the menu list or change the settings

▼

(16) To enter the OSD Main menu / Exit from the main menu or sub-menu display

(17)

ZOOM+

To zoom in view of PTZ camera ZOOM-

To zoom out view of PTZ camera

(18) PTZ PTZ camera control button. Press PTZ + camera channel

button( 1 2 3 4 )can enter PTZ mode to control PTZ camera.(see 2.1.3)

(19)

SPEED+

To speed up movement of PTZ camera lens SPEED-

To speed down movement of PTZ camera lens

(20)

FOCUS +

To focus in PTZ camera lens FOCUS -

To focus out PTZ camera lens

(21) Make a selection

Enter sub-menu

(22) REC Start video recording

2.1.1 Using AB Repeat Function AB Repeat function allow user to set a video segment from A to B point and play on the surveillance screen until user stop. User also can backup AB Repeat file to pen drive or external hard disk (See 2.1.2). 1. Press ▲ (play button) to call out the

SEARCH MODE menu to find the recorded video that user wants to playback.

2. Select TIME SEARCH or EVENT LIST. - TIME SEARCH (search by date and time): select the date and time from where you

want to begin the video playback. - EVENT LIST (search by condition): select from the list.

3. During the playback, press A-B to set the A point of video segment. And then, press

13

USB BAKCUPYES(SELECT) / NO(MENU)

A-B again to set the B point of video segment. On the surveillance screen will display

“A-B” and repeat playing the AB point video segment which user has set. To cancel AB

repeat, press A-B again.

2.1.2 Using USB Backup Button User can press button to backup the AB Repeat video

file. 1. Set the AB Repeat file (see 2.1.1). 2. Plug in pen drive or external hard disk to DVR system. 3. During the AB Repeat playback, press button. 4. And then, press (YES) to start backup file or press

(NO) to exit backup mode.

i - If the external hard disk is first time using, please format to FAT32 format.

- The external hard disk needs to be powered by external power.

2.1.3 Controlling PTZ Camera Using remote control, user can easily control PTZ camera at local site. Before starting, please go to OSD menu to enable PTZ control (see 3.1 Menu Function: PTZ Setup).

2.1.3.1 To Enter the PTZ Mode To control PTZ camera, user need to enter the PTZ mode first. Press PTZ button, and

camera channel number button ( 1 2 3 4 ). The surveillance monitor will switch to

single screen and display “PTZ mode” on the screen.

To exit PTZ mode, press PTZ and 0 button. Also, when user doesn’t have any action

over 1 minute, the system will automatically exit PTZ mode.

14

2.1.3.2 To Set Preset Position

User can set 9 preset positions for PTZ camera. Using 1 to 9 button to set the

preset position.

1. Press PTZ and camera channel number button ( 1 2 3 4 ) to enter PTZ mode.

2. Using ▲ , ▼ ,

▼

and ▼ to adjust the PTZ camera to the position that user wants.

3. Press any number button over 3 seconds and the position will be saved. 4. To move the PTZ camera to preset position, just press the number button.

2.1.3.3 To Control PTZ Camera

To move, adjust focus, and zoom in/out camera lens can be done by using some function buttons on the remote control.

▼ To move the PTZ camera lens to the right

▼

To move the PTZ camera lens to the left

▲ To move the PTZ camera lens to go up

▼ To move the PTZ camera lens to go down ZOOM+

To zoom in PTZ camera ZOOM-

To zoom out PTZ camera

SPEED-

To speed down movement of PTZ camera lens

SPEED+

To speed up movement of PTZ camera lens FOCUS +

To focus in PTZ camera lens FOCUS -

To focus out PTZ camera lens

2.2 Using the DVR for the First Time Upon connecting the power, the unit automatically detects the status of the hard disk. The hard disk must be formatted before user can use it with EB1304NET SATA. If you are prompt to format the hard disk, press (select) for YES to format the hard disk and

(menu) for NO to remain unchanged.

15

TIME SETUP

TIMEAUTO SYNC TIMETIME ZONELAST SYNC TIME

DAYLIGHT SAVINGDELETE RECORDED FILES OLDER THAN

10 DAYS

2007 / 03 / 1215 : 45 : 57OFFGMT2007 / 03 / 1212 : 00 : 00

DATE

HARD DISKS INFORMATIONVERSION S3 . 01. 01. 00. 03

MASTER HDD

HDD FORMAT YES (SELECT) / NO (MENU)

HDD CHECKING . . .

SIZE 76GB 509MB

2.2.1 Set up the System Date and Time Before starting record video, adjust the date and time first. 1. Press to call up the OSD menu and then use ▲ and ▼ to go up and down

and select Submenu. And then, press or ▲ to confirm the selection.

2. In Submenu, use ▲ and ▼ to go up and down and select the Time Setup and press again to make a selection. And then, use ▲ and ▼ to select the Date and press or ▲ to confirm the selection.

3. To adjust the date, use ▼

and ▼ or ▼▼ and

▼ ▼ buttons to move the selection to the left and right.

4. To adjust Time, follow the above step 2 and 3. 5. Press to go back to main menu after adjustment.

2.3 Surveillance Screen To know if the channel is being recorded, the “ ” record symbol would appear beside the channel number. The (microphone) and (speaker) indicate that the audio is available. The information below the screen shows the current date and time, recording mode (record schedule setting), and the percentage of the used hard disk space.

Full Screen Preview

Quad mode Preview

When you are in full screen preview, press the following buttons on the remote control to switch to different channel, or preview all 4 channels:

16

1

CH1: Camera1

3

CH2: Camera 2

7

CH3: Camera 3

9

CH4: Camera 4

5

QUAD: 4-Channel

17

2.4 Playback the Video The DVR system can record and playback video simultaneously. Therefore, user don’t need to stop recording while playback the video.

1. Press ▼

2. Use the ▲ and ▼ buttons to go up and down and

select TIME SEARCH or EVENT LIST. Then, press

or ▼ to make a selection.

SEARCH METHODTIME SEARCHEVENT LIST

TIME SEARCH (search by date and time):

1. Use the ▲ and ▼ buttons and select SEARCH

TIME. Then press or ▼ again to make the

selection.

2. In the SEARCH TIME, user may now select the date and

time from where you want to begin the video playback.

MASTERTIME SEARCHHARD DISK :

START TIMEEND TIME : 2006 / 05 / 05 13 : 08 : 13

: 2006 / 05 / 04 10 : 00 : 01

: 2006 / 05 / 04 10 : 00 : 01SEARCH TIME

Use the

▼

and ▼ buttons to move the selection to the left and right. Use the ▲ and ▼

buttons to select the date and time. Then press or ▼ again to make the selection.

3. To start video playback, the time in second must be set. Use the ▼ buttons to move the selection

to the right most. Use the ▲ and ▼ buttons and select the time in second. Then press

or ▼ . EVENT LIST (search by event):

1. Use the ▲ and ▼ buttons to select from the list.

Press or ▼ again to make the selection. User

and to go next page or back to

previous page.

2. Listed below are the following recording conditions:

A – Always Recording It records non-stop and automatically continue recording when interrupted

EVENT LISTHARD DISK : MASTER

SA

2006 / 05 / 032006 / 05 / 03

13 : 26 : 3413 : 00 : 01

13 : 26 : 5013 : 16 : 46

A 2006 / 05 / 03 12 : 00 : 01 13 : 00 : 01B 2006 / 05 / 03 11 : 48 : 37 12 : 00 : 00A 2006 / 05 / 03 11 : 30 : 23 11 : 31 : 18A 2006 / 05 / 03 11 : 29 : 47 11 : 30 : 13S 2006 / 05 / 03 11 : 28 : 55 11 : 28 : 58B 2006 / 05 / 03 11 : 28 : 33 11 : 28 : 55A 2006 / 05 / 03 11 : 25 : 41 11 : 28 : 32A 2006 / 05 / 03 11 : 23 : 26 11 : 23 : 30

S – Sensor Recording It records when the sensor has triggered M – Motion Recording It records when any movement has detected B – Button Recording

It records when the REC record button is pressed

3. The “ ” play symbol would appear beside the channel number when you are previewing in playback mode.

18

Chapter 3 OSD Navigation Tree The follow figure is an OSD menu tree map. To call out the OSD menu, press on the remote control.

RECORD SCHEDULE

13 : 00 - 14 : 0014 : 00 - 15 : 0015 : 00 - 16 : 00

18 : 00 - 19 : 0019 : 00 - 20 : 0020 : 00 - 21 : 0021 : 00 - 22 : 0022 : 00 - 23 : 0023 : 00 - 00 : 00

17 : 00 - 18 : 0016 : 00 - 17 : 00

ALWAYS REC

ALWAYS REC

ALWAYS RECALWAYS REC

ALWAYS REC


ALWAYS REC



ALWAYS REC

ALWAYS RECALWAYS RECALWAYS RECALWAYS REC

RECORD SCHEDULE00 : 00 - 01 : 0001 : 00 - 02 : 0002 : 00 - 03 : 00

05 : 00 - 06 : 0006 : 00 - 07 : 0007 : 00 - 08 : 0008 : 00 - 09 : 0009 : 00 - 10 : 0010 : 00 - 11 : 0011 : 00 - 12 : 0012 : 00 - 13 : 00

04 : 00 - 05 : 0003 : 00 - 04 : 00

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC

ALWAYS REC


ALWAYS REC

1 2 3 41 2 3 41 2 3 41 2 3 4

D1DMPEG460GOOD

ENGLISH

MAIN MENUCAMERA SELECTRECORD SELECTRECORD MODEVIDEO FORMATRECORD FRAMERATEVIDEO QUALITYRECORD SCHEDULESUBMENUHARD DRIVE SETUPSENSOR SETUPMOTION SETUPNETWORK SETUPUSB BACKUPLANGUAGE SETUP

ON

ONOFF

NO

SUBMENUPASSWORD CHANGEVIDEO ADJUSTMENTTIME SETUPAUTO RECORDAUTO SCANPASSWORD SETUPAUDIO RECORDAUDIO MUTE

NTSCOFF1

VIDEO SYSTEMMULTIPLE REMOTEREMOTE IDPTZ SETUPCHANNEL NAME SETTING

S3. 01. 01. 00. 03

PASSWORD SETUPSUPERUSERUSER(NETWORK)

1

050050

000024

VIDEO ADJUSTMENTCAMERABRIGHTNESSCONTRASTHUESATURATIONRESET TO DEFAULT VALUE

OFF10 SEC10 SEC10 SEC10 SEC

AUTO SCANAUTOCHANNEL-1CHANNEL-2CHANNEL-3CHANNEL-4

NOHARD DRIVE SETUPOVERWRITE ENABLEDHD1 SIZE 37 GB 78MBHD1 USED 16 GB 219MB 21%HD1 FORMAT

010 SEC010 SECNOT INSTALLEDNOT INSTALLEDNOT INSTALLEDNOT INSTALLED

SENSOR SETUPSENSOR REC TIMEALARM OUT TIMECHANNEL - 1CHANNEL - 2CHANNEL - 3CHANNEL - 4

1 2 3 4HI010 SEC

MOTION SETUPMOTION CAMERASENSITIVITIYMOTION RECORD TIME

1 2 3 4

50051

5001

STATICNETWORK SETUPIP MODENW ENABLEVIDEO PORTUPGRADE PORTUSERSET NW PASSWORD

1 2 3 4

2006/09/23 17:00:02

73G 89MB

2006/09/26 18:00:00

USB BACKUPTIME SETSTART :END :BACKUP CHANNELBACKUP SIZEBACKUP EXECUTE

PASSWORD SETUPCURRENTNEWCONFIRM

SET NW PASSWORDCURRENTNEWCONFIRM

VIDEO LOSS ALARM 1 2 3 41 2 3 4

000PELCO-D24001-1

PTZ SETUPCAMER APTZ CONTRO LPTZ IDPRO TOCO LBAUD R ATEAUTO PAN

05 SECDWEL L TIME

1OFF

CH01CH02CH03CH04

CHANNEL NAME SETTINGCHANNEL 1 NAMECHANNEL 2 NAMECHANNEL 3 NAMECHANNEL 4 NAME

19

3.1 Menu Function If the unit is currently recording the video, user may have to stop video recording to change the settings. Use remote control to navigate in the OSD menu. The red frame turns yellow when you are making a selection.

OSD MENU Description

1 2 3 41 2 3 4

D1MP E G4

60GOOD

E NGL IS H

MAIN ME NUC AME R A S E LE CTR E C OR D S E LE C TR E C OR D MODEVIDE O FOR MATR E C OR D FR AME R ATEVIDE O QUALITYR E C OR D S C HE DULES UB ME NUHAR D DR IVE S E TUPS E NS OR S E TUPMOTION S E TUPNE TWOR K S E TUPUS B B AC K UPLANGUAGE S E TUP

CAMERA SELECT Enable/disable the channel number to display the video on the surveillance screen

RECORD SELECT Enable/disable the channel number to record video

i

The channels which could be recorded should be enabled in the CAMERA SELECT first.

RECORD MODE Select D1/CIF recording mode Under D1 mode, the video recording is in full screen resolution and takes turns from one channel to the next one when Auto Scan enables. Each channel is recorded only at a maximum frame rate of 15fps. User can switch to view the video in single full screen or QUAD screen Whereas in CIF mode, video recording is at a lower resolution, but each video is recorded in 30fps/25fps (NTSC/PAL). User can switch to view the video in single full screen or QUAD screen

VIDEO FORMAT The recorded video is in MPEG4 format RECORD FRAME RATE Set the number of frames per second to be recorded. Refer to the table below for the available record frame rate settings. The higher the frame rate is, it uses more hard disk space

Video Standard Record Mode

NTSC PAL

D1 60, 20, 4 48, 20, 4

CIF 120, 60, 40, 20, 4 100, 48, 20, 4

VIDEO QUALITY Select the video quality setting from BEST, HIGH, MEDIUM, GOOD, NORMAL or LOW. BEST – best record quality but less record hours LOW – longest record hour but quality is ordinary NORMAL – allows you to record more hours but the quality of the recorded video is moderate.

LANGUAGE SETUP Select from the available languages

20

OSD MENU Description R E C OR D S C HE DULE00 : 00 - 01 : 0001 : 00 - 02 : 0002 : 00 - 03 : 00

05 : 00 - 06 : 0006 : 00 - 07 : 0007 : 00 - 08 : 0008 : 00 - 09 : 0009 : 00 - 10 : 0010 : 00 - 11 : 0011 : 00 - 12 : 0012 : 00 - 13 : 00

04 : 00 - 05 : 0003 : 00 - 04 : 00

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E C

ALWAYS R E CALWAYS R E C

ALWAYS R E C

RECORD SCHEDULE By default, in 24 hours, the recording schedule is set to always record every hour. Refer to the table below to customize the recoding condition

Condition Description

NO REC Disable video recording

ALWAYS REC Record non-stop

MOTION REC Start recording when any movement is detected

SENSOR REC Start recording when the sensor has triggered

BUTTON REC Start recording when the record button is pressed

ON

ONOFF

NO

S UB ME NUPAS S WOR D CHANGEVIDE O ADJ US TME NT

AUTO R E C OR DAUTO S C ANPAS S WOR D S E TUPAUDIO R E C OR DAUDIO MUTE

NTS COFF1

VIDE O S YS TE MMUTIPLE R E MOTER E MOTE IDPTZ SETUPCHANNEL NAME SETTING

S3. 01. 01. 00. 03

TIME SETUP

PASSWORD CHANGE Set a security combination number. There are two type of user password – SUPERUSER and USER. PAS S WOR D SETUPS UPE R US E RUS E R (NE TWOR K )

Use the number button on the remote control to enter the password. Or use ▲ and ▼ button to the select the

security combination number. Press or ▼ button to confirm.

SUPERUSER Superuser has the authority of formatting hard disk, changing system settings, remote monitor the DVR system and changes the system settings. The factory default password is 111111. PAS S WOR D S E TUPCUR R E NTNE WCONFIR M

21


ON

ONOFF

NO



NTS COFF1


S3. 01. 01. 00. 03

TIME SETUP

USER(NETWORK) The login account for remote connection through the internet. User account only can view and playback recorded video by Web viewer (ex: Internet Explorer), but no authority to change the DVR system’s setting. The factory default password is 111111. PAS S WOR D S E TUPCUR R E NTNE WCONFIR M

VIDEO ADJUSTMENT

Select the camera number and set to adjust the video brightness, contrast, hue, and saturation value

1

142083

130130

VIDEO ADJUSTMENTCAMERABRIGHTNESSCONTRASTHUESATURATION

NORESET TO DEFAULT VALUE

TIME SETUP



10 DAYS

2007 / 03 / 1215 : 45 : 57OFFGMT2007 / 03 / 1212 : 00 : 00

DATE

TIME SETUP Setup system date, time, daylight saving, and enable auto synchronize time through network.

DATE Set the current date

TIME Set the current time

AUTO SYNC TIME Enable/disable time synchronization automatically through network. The DVR system will auto synchronize time from NTP servers. The first time synchronize will be 6 hours later after system power up. When the daylight saving is enabling, the auto time synchronization will be stopped.

i- User need to setup the NTP server’s URL or IP address.

Please go to 8.1.1.1 System Setting #(3) NTP Setting to setup the NTP server.

- If the NTP server doesn’t setup, the auto synchronizetime function will not work correctly.

TIME ZONE Select the time synchronization time zone. The time zone will base on GMT (Greenwich Mean Time) time zone.

LAST SYNC TIME Display the latest time synchronization date and time.

22


TIME SETUP



10 DAYS

2007 / 03 / 1215 : 45 : 57OFFGMT2007 / 03 / 1212 : 00 : 00

DATE

DELETE RECORDED FILES OLDER THAN 0 DAYS

Set a period of time to delete recorded files that save on hard disk.

DAYLIGHT SAVINGDAYLIGHT SAVINGSTARTEND

TIME OFFSET

OFF2008 / 01 /0100 : 002008 / 06 /3000 : 0000 : 00

DAYLIGHT SAVING To enable/disable daylight saving function.

START Setup daylight start up date and time.

END Setup daylight stop date and time.

TIME OFFSET Assign a time that it is for daylight saving time offset in your time zone. For example: if the time zone is in U.S. Eastern, the time offset is 1 hour.

ON

ONOFF

NO



NTS COFF1


S3. 01. 01. 00. 03

TIME SETUP

AUTO RECORD

Enable/disable auto continue recording when interrupted (i.e., power breakdown, video playback or configuration setup). It continue recording after 10 second of idleness. This is applicable in Always Record mode

AUTO SCAN

Enable/disable auto cycle switch to display the next channel when in full screen preview. User can set different switch time for each channel. The time range is from 5 ~30 seconds.

OFF10 SEC10 SEC10 SEC10 SEC

AUTO SCANAUTO SCANCHANNEL - 1CHANNEL - 2CHANNEL - 3CHANNEL - 4

PASSWORD SETUP Enable/disable full system password protection. This would prevent unauthorized user to stop video recording, change system settings and formatting the hard disk

AUDIO RECORD Enable/disable audio recording. To record sound, make sure the audio input device(ex: microphone) is connected to the unit

23


ON

ONOFF

NO



NTS COFF1


S3. 01. 01. 00. 03

TIME SETUP

AUDIO MUTE Enable/disable to hear audio sound. To hear sound, make sure the unit is connected to an audio output device (ex: speaker). If user recorded video in audio mute status, there is no sound when playback

i

The audio input and output device need to be powered by external power.

VIDEO SYSTEM DVR system will auto detect the video system and display

MUTLIPLE REMOTE Enable/disable multiple DVR system remote control. When user has more than one DVR system, user can use MULTIPLE REMOTE function to control all DVR system by single remote control.

REMOTE ID Assign the ID number for multiple DVR system remote controls. When there are more than one DVR systems, user can enable MULTIPLE REMOTE function, and then assign REMOTE ID to each DVR system. Then, user can just use one remote control to control all DVR system by pressing REMOTE ID. To remote

control multiple DVR systems, press FN and number key

(remote ID number) on the remote control.

000PELCO-D24001-1

PTZ SETUPCAMERAPTZ CONTROLPTZ IDPROTOCOLBAUD RATEAUTO PAN

05 SECDWELL TIME

1OFF

PTZ SETUP To enable PTZ camera control by remote control and setup PTZ camera parameters. 1. Press and select SUBMENU → PTZ SETUP.

2. Use the ▲ and ▼ to go up and down to select the item and change the parameter value.

3. Use ▼ or ▼ ▼ button to enter the configure mode.

Press or

▲

button to confirm the selection.

CAMERA Select the channel of PTZ camera. If the PTZ camera is connecting on channel 1, then select the camera 1 for PTZ video to be display on channel 1.

PTZ CONTROL

To enable/disable PTZ camera can be controlled by remote control at local site.

PTZ ID Assign an ID to PTZ camera. The ID range is from 001 to 255 but is limiting by protocol of PTZ camera. Please refer to your PTZ camera user’s manual for more detail of PTZ ID assignment.

i We suggest assigning PTZ camera ID start from 5 to avoid conflict with ID of camera channels.

24


000PELCO-D24001-1

PTZ SETUPCAMERAPTZ CONTROLPTZ IDPROTOCOLBAUD RATEAUTO PAN

05 SECDWELL TIME

1OFF

PROTOCOL Select the protocol of PTZ camera. The protocol will be differenced that depends on the brand of PTZ camera. The DVR system currently supports 2 protocols ─ PELCO-D and PELCO-P. Please refer to your PTZ camera user manual to make sure which protocol is using for.

BAUD RATE To setup the baud rate of PTZ camera. For more detail, please refer to your PTZ camera’s user manual.

AUTO PAN Select the preset number to assign an auto move direction for the PTZ camera. For example: 1-3 means the PTZ camera will auto move from preset position 1, 2 and 3.

DWELL TIME

Set a time that how long the IP PTZ camera stays in that position before it moves to the next one.

CH01CH02CH03CH04

CHANNEL NAME SETTINGCHANNEL 1 NAMECHANNEL 2 NAMECHANNEL 3 NAMECHANNEL 4 NAME

CHANNEL NAME SETTING User can define name of each channel. Channel name can be 7 digit long that include A~Z, 0~9, space, and dash (-).

25


YESHARD DRIVE SETUPOVERWRITE ENABLEDHDD SIZE 1560,12MBHDD USED 250MB 1%HDD FORMAT

* HDD SIZE shows the total capacity

of the hard disk. * HDD USED shows the amount of

space that has been used.

OVERWRITE ENABLED

Enable/disable overwriting the earliest record when the hard disk space runs out. By default, the HDD overwrite setting is enabled

HDD FORMAT

For security purpose, you may have to enter the password to format hard disk

To format hard disk:

1. Use the ▲ and ▼ buttons to go up and down and

select HDD FORMAT. Then press or ▼

2. In the CHECK PASSWORD screen, press or ▼ .

Then use the ▲ and ▼ buttons to select the security combination number. Repeat till you key in the last number. Also, user can use the number button on the remote control to enter the password. Press or ▼ button again to make the selection. To move the selection to the left and right, use ▲ and ▼ buttons

CHECK PASSWORDENTER PASSWORD

3. After entering the last number, the system will format the

hard disk 4. It is done when the “HDD FORMAT COMPLETED” appears

YESHARD DRIVE SETUPOVERWRITE ENAB LED

HDD FORMAT COMPLETED

HDD SIZE 156 ,012 MBHDD USED 0MB 0%HDD FORMAT

Formatting the hard disk will permanently delete all the records and can no longer be retrieved

26


010 SEC010 SECNOT INSTALLEDNOT INSTALLEDNOT INSTALLEDNOT INSTALLED

SENSOR SETUPSENSOR REC TIMEALARM OUT TIMECHANNEL - 1CHANNEL - 2CHANNEL - 3CHANNEL - 4VIDEO LOSS ALARM 1 2 3 4

SENSOR REC TIME Set the amount of time (in second) to start record when the sensor has triggered

ALARM OUT TIME Set the amount of time (in second) to continue sending the alarm once triggered

CHANNEL 1~4 Customize the initial state of the attached sensor. Refer to the table below to customize the sensor state

Condition Description

NOT INSTALLED Indicates that there is no sensor connected

NORMAL OPEN Indicates that the initial state of the sensor is normal open. Video recording initiates when there is a changes in the sensor state

NORMAL CLOSE Indicates that the initial state of the sensor is normal close. Video recording initiates when there is a changes in the sensor state

VIDEO LOSS ALARM

Select the channel when the video loss that the DVR system will send out a alarm

1 2 3 4MEDIUM010 SEC

MOTION SETUPMOTION CAMERASENSITIVITIYMOTION RECORD TIME

MOTION CAMERA Enable/disable the channel number to detect motion. SENSITIVITY Set the sensitivity level. The sensitivity is from H (High), 9~ 2 and L (Low). MOTION RECORD TIME Set the amount of time (in second) to record when motion is detected.

1 2 3 400805005

NETWORK SETUPIP MODENW ENABLEVIDEO PORTUPGARDE PORT

STATIC

NETWORK SETUP Setup the network parameters for the internet or intranet remote monitor or playback.

IP MODE The system provides 3 types of IP setup mode – Static, DHCP, and PPPOE.

Use ▲ and ▼ buttons to go up and down and select IP

MODE, and then press . Use ▲ and ▼ buttons to

change the selections and press or ▼ to make a selection.

STATIC: Assigns a constant IP address for the DVR system. Use ▲ and ▼ buttons to go up and down

and select items, and then press or ▼ to make

selection. Use

▼

and ▼ to move left and right to select or enter the configuration value. - IP ADDRESS: Assign a constant IP address which a real

IP addresses give from ISP to DVR system.

27


1 2 3 400805005


DHCP

- SUBNET: It is a bitmask used to identify the sub network and how many bits provide room for host addresses. Enter the subnet mask of the IP address which user has assigned to DVR system.

- GATEWAY: A network device act as a passageway to internet. Enter the network gateway IP address

- DNS: Domain Name Server translates domain names (such as www.abb.com.tw) to IP addresses. Enter the IP address of DNS if it is available.

- MAC ADDRESS: Only for user information. Don’t need to enter the MAC address.

- When all parameters are set, select the CHANGE to confirm the configuration.

192.168.153 .254192.168.153 .100.00 .00 .00.00.00

NE TWOR K INFOR MATIONIP ADDR E S SS UB NE TGATE WAYDNSMAC ADDR E S SCHANGE

192.168.153 .100255.255.255.255

DHCP: Assign the IP address by local DHCP server to

DVR system. Use ▲ and ▼ buttons to go up and

down and select DHCP, and then press or ▼ to make selection.

i The DHCP (Dynamic Host Configuration Protocol) is a set of rules used by a communications device (such as a computer, router or networking adaptor) to allow the device to request and get an Internet address from a server which has a list of addresses available for assignment

The DVR system will try to get an IP address from the DHCP server. A message window will show up as below:

G E T IP NOW ! W AIT ING .. .

When DVR system gets an IP address from DHCP server, the information will display as below:

192.168.153 .254192.168.153 .100.00 .00 .00.00.00

NE TWOR K INFOR MATIONIP ADDR E S SS UB NE TGATE WAYDNSMAC ADDR E S S

192.168.153 .100255.255.255.255

28


1 2 3 400805005


PPPOE

PPPOE: Point-to-Point Protocol over Ethernet is a network protocol for encapsulating PPP frames in Ethernet frames. It is used mainly with ADSL services. If your network is using ADSL service connecting to internet, and then, select PPPOE mode. Use ▲ and ▼ buttons to go up and

down and select PPPOE, and then press or ▼ to make selection. A message window will show up as below:

G E T IP NOW ! W AIT ING .. .

When DVR system get an IP address, the information will display as below:

192.168.153 .254192.168.153 .100.00 .00 .00.00.00

NE TWOR K INFOR MATIONIP ADDR E S SS UB NE TGATE WAYDNSMAC ADDR E S SCHANGE

192.168.153 .100255.255.255.255

NW ENABLE Allow internet remote user to playback or monitor the channels. Without enabling the network function, the channels cannot be playback or monitor from remote site.

i 1 is Channel 1 2 is Channel 2

3 is Channel 3 4 is Channel 4

Use ▲ and ▼ buttons to go up and down and select

NW ENABLE (network enable), and then press or

▼

and ▼ to move to the selection. Use ▲ and ▼ buttons

to change the selections values and press or ▼ to confirm.

VIDEO PORT A port for the remote connection. Any port can be assigned as a video port, except the ports already used by the network services. The default video port is 80.


VIDEO PORT, and then press or

▼

and ▼ to move

to the selection. Use ▲ and ▼ buttons to change the

selections values and press or ▼ to confirm.

29


1 2 3 400805005


STATIC

UPGRADE PORT A port for the remote update DVR system firmware. Any port can be assigned as an upgrade port, except the ports are already used by the network services. The default upgrade port is 5005. For Upgrading DVR firmware, please contact your local dealer.

i Please DO NOT cut off the power of the DVR system while the firmware is upgrading. Power failure will cause the permanent damage of the DVR system.


UPGRADE PORT, and then press or

▼

and ▼ to

move to the selection. Use ▲ and ▼ buttons to change

the selections values and press or ▼ to confirm.

USB BAKCUPTIME SET

STARTEND : 2006 / 05 / 05 13 : 08 : 13

: 2006 / 05 / 04 10 : 00 : 01

BACKUP CHANNELBACKUP SIZEBACKUP EXECUTE

1 2 3 4 89MB

USB BACKUP Using USB device (ex. Pen drive or External Hard disk) to backup partial recorded video and playback on PC.


USB BACKUP, and then press or ▼ . Use

▼

and

▼ to move left and right. And, use ▲ and ▼ buttons

to change the value and press or ▼ to confirm.

i - Remember to plug in the USB device before starting to backup.

- If the external hard disk is first time using, please format to FAT32 format.

- The DVR system supports external hard disk capacity up to 32GB.

- The external hard disk needs to be power by external power.

1. Select the START TIME and END TIME.

2. Select the channels which user wants to backup. 3. The DVR system will display the system hard disk space

and backup file size. 4. And then, select BACKUP EXECUTE to start backup

video to the USB device. 5. When backup is done, press any key to back to main

menu.

USAGE OF USB WIL L STOP NETWORKFUNCTIONS!YES(SELECT) / NO(MENU)

USB BACKUP !

6. To view the backup file, using USB Playback Application(see 4.3)

30

Chapter 4 Using the USB Playback Console 4.1 Recommended system requirements

Pentium®4 2.4GHZ or above Windows®2000/ XP/Vista DDR 256 MB Graphic function must support DirectDraw Audio card or built-in Speaker 1 available USB2.0 port

4.2 Installing the USB Playback Console To install the USB Playback Console: 1. Place Installation CD into the CD-ROM drive. When the installation main screen

appears, click Install USB Playback Console and then follow the on screen instructions

2. Select the language you prefer

3. Click OK to install the application 4. Click Exit to close the installation main screen. You may plug in the pen drive or

connect the external hard disk to the PC now.

31

4.3 Running the USB Playback Console To run the application, click the icon on the PC desktop

Name Function

(1) Exit Exit/ Minimize the application or chose Cancel to go back to the application.About: shows DVR application version information.

(2) Progress bar Show the progress of the file being played. You may move the bar to seek at

any location of the track.

(3) Split Screen Mode Select from different screen view to playback the recorded video file of the entire camera or one camera on screen.

(4) Playback Controller

Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame by frame. Slower: Play the recorded video file at the speed of 2x, 4x, or 8x. Rewind: Wind back the recorded video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, 8x, or 16x Next: Go to the next frame by frame. End: Go to the end of the recorded video file.

32

Name Function

(5) Open File To select the video file for playing. The playback application supports *.dvr and *.avf file type.

- DVR Recorded File (HD): To playback the recorded video from the hard

disk which was recording video on the DVR system. (see aslo Chapter 4.3.2)

- Backup File(.dvr): The file is backup and save in *.dvr file format. (see also Chapter 4.3.3)

- Backup File(.avf): The file is backup and save in *.avf file format. The recorded video backup to pen drive is in *.avf (see also 4.3.4)

(6) Status bar Display the recorded date, time and play speed.

(7) Camera ID Show the number of cameras that are being viewed. When you are in single screen mode, click the camera ID number to switch and view other camera.

(8) Adv. Function Advanced function is including : HDD Backup: to call out HDD Backup application. (see also Chapter 5) iEnhance: to call out iEnhance application. ( see also Chapter 7)

(9) Export Export includes Snapshot, Print, Output Video Clip, and Backup function. Snapshot: Capture and save the screen shot either in *.jpg or *.bmp format. Print: Print the screen shot. Output to AVI: Save the segmented file in *.avi format

(10) Segment Keep a portion of the recorded video (see also Chapter 4.3.1)

(11) Full screen Use the entire area of the screen to only display the video. To return, press the right button of the mouse or ESC on the keyboard. When you switch to full screen in multiple-screen mode, Left click to toggle to only display one of the video in the multiple-screen mode or all.

(12) Event List Select the event you want to playback. The event list only available when user select to playback in DVR Recorded File(HD).

(13) Sound /Sound bar Turn on and off the sound Increase and decrease the volume

(14) Watermark To call out Image Verification application. (see also Chapter 6)

33

4.3.1 To Cut and Save the Portion of the Recorded Video 1. Use the Playback Control buttons or drag the bar on the playback progress bar and

pause on where you want to start the cut. Then, click Segment to set the begin mark.

2. Use the Playback Control buttons or drag the bar on the playback progress bar and pause on where you want to end the cut. Then, click Segment to set the end mark. To cancel segmentation, click Segment button again.

3. Click Output button to save the wanted portion. 4. In the Save As dialog box, locate on where user wants to save the file, type the

filename, and select the video format.

4.3.2 Playback DVR Recorded File from Hard Disk 1. Please have the hard disk which containing of recorded video data install on your PC

or using external USB enclosure to connect to your PC.

2. Click Open File button

3. Select DVR Recorded File(HD) and click OK.

4. Select the hard disk drive from Select Disk window and click OK.

5. And then, the Event List window appears. Select the event that user wants to play and

click OK.

34

4.3.3 Playback Backup File(*.dvr) - Click Open File button.

- Select Backup File(*.dvr) and click OK.

- Locate the backup file folder and click OK.

i

When open the backup video file, just locate the where backup file folder is.

- And then, Playback Date/Time Selection window appears. Select the date and time and click OK.

4.3.4 Playback Backup File (*.avf) To playback backup file in *.avf format, user can use the AVFPlayback application that included in backup folder when backup into USB storage device. Also, user can use USB Playback Console to playback backup file (see also Chapter 4.3). 1. Plug the USB storage device into PC USB port. 2. Run AVFPlayback from USB storage device 3. Click Open in AVFPlayback UI 4. Click Select Folder to locate the backup files

5. And then, select the backup file and click OK

35

Chapter 5 Backup Recorded Video File HDD Backup application provides user an interface to view recorded video from hard disk.

5.1 Familiarizing with HDD Backup Application

(1)

(2)

(3)

(4)(5)(6)

(7)

(8)(9)

(10)(11)(12)

(13)(14) Name Function

(1) Date Select the date for events

(2) Hour and Channel User can select the hour and channel for events. : All events in this hour and channel have been selected. : In this hour and channel has events : Partial of events in this hour and channel has been selected.

(3) Event list All recorded video events list No.: the list order number Record: the record type(see also Chapter 2.4) Begin Time: the beginning of record time End Time: the end of record time

(4) Set Marked File Use Ctrl and mouse to select the multiple events from event list, and then click Set Marked File to mark multiple events. When click Set Marked File button, the marked event will turn to un-mark and un-mark event will turn to marked.

(5) Page Switch

Pre: go back last page Next: go to next page Page column: enter the page number and click Go button to go to the page

(6) Select All Select all listed recorded video events. Click the check box again to cancel for selecting all events.

(7) Video display Display first frame of each recorded video channel from 4 selected.

36

Name Function

(8) Progress bar Show the progress of the event being played. User may move the bar to seek at any location of the track

(9) Source Disk To select the hard disk drive

(10) Target Path To locate on where user wants to save the file (11) Event (%) Display the backup progress rate of event in percentage (12) Total (%) Display the total backup progress rate in percentage (13) Stop Stop backup progress (14) Start Start backup progress

5.2 To Backup Recorded Video File 1. Please have the hard disk which was recording video on the DVR system install on

your PC or using external USB enclosure to connect to your PC. 2. To run the HDD Backup application, click the HDD Backup button on USB Playback

Application main interface. 3. Click Browse in Source Disk to locate the recorded video file. 4. And then, the Select Disk windows will appear as below:

5. Select the hard disk drive from Select Disk windows. All available hard disk will list on the Select Disk windows with size and name

6. Select the hard disk drive and click OK 7. And then, all the recorded video files will list out. 8. Select the event which user wants to backup. Or mark the Select All to select all listed

recorded video event 9. Locate on where user wants to save the backup file 10. Click Start to process backup 11. To stop the backup progress, click Stop 12. To play the backup file, see 4.3.3.

37

Chapter 6 ImageVerification Image Verification is a watermark-checking program to identify the authenticity of a saved image (e.g. by snapshot). This program can only verify uncompressed bmp image files.

6.1 To Run the ImageVerification 1. To run the ImageVerification application, click the Watermark button on USB Playback

Application main interface. 2. In the ImageVerification screen, click Load Source Image and locate the image

source. 3. Click Verify Image to begin the process. 4. Check the result in the Processed Image screen. If the picture is unmodified, the

image in the Source Image and Processed Image screen would be exactly the same. If the picture is being modified, a warning dialog box would prompt and the modified area is highlighted.

38

Chapter 7 iEnhance The bundled iEnhance is a video editing tool and can only be used with *.dvr video file. It allows you to adjust the video picture quality, segment and save the selected portion of the video, zoom in and out the image, and print or save the screen shot. You can also save the setting and apply it on other files. To run iEnhance application, click iEnhance button on USB Playback Console interface.

(1) (2) (4)(3) (5) (6)

(14)

(13)

(11)(12)

(10)

(16)

(17)

(21)

(19)

(18)

(22)(23)(24)(25)

(9)

(15)

(8)(7)

(20)

Name Function

(1) Open File Access *.dvr video file.

(2) Save Image Capture and save the screen shot in *.bmp format.

(3) Playback Control Buttons

Begin: Move at the beginning of the video file. Previous: Go back to previous frame. Pause: Briefly stop playing the video file. Play: Play the video file. Faster: Play the video file at the faster speed. Next: Go to the next frame. End: Go to the end of the video file.

(4) Save Video Save the edited or segmented video in *.avi format.

(5) Print Print the screen shot.

(6) Segment Mark the beginning and the end of the selected portion of the video. Two triangle marks will appear on the slider. To cancel video segmentation, click this button again.

(7) Zoom Buttons Enlarge, reduce, and set the image back to normal size.

(8) Full Screen Use the entire screen to only display the video.

(9) Default Set the video back to original state and delete all the changes in the history box.

(10) History Box List all the actions.

(11) Undo Delete the last action.

(12) Noise Reduce Adjust the softness and repair the damaged colours.

39

Name Function

(13) Sharpness Improve the overall image by enhancing edges. This gives the image more depth.

(14) Effects Gray Scale: convert the image into black and white (monochrome). Normalize: adjust the brightness intensity. Equalize: automatically adjust the images that are too dark. De-interlace: smooth out the overlying frames.

Static: de-interlace for motionless scene. Dynamic: de-interlace for moving scene.

(15) Picture Adjustment

Adjust the Brightness, Contrast, Saturation, Hue and Gamma.

(16) Original Screen Display the original state of the image.

(17) Temporary Setting Block

Display the sample settings. Click the sample to apply the setting on the current video.

(18) Status Bar Display the date, and time of the video.

(19) Progress Bar Show the progress of the file being played. You may move the bar to seek at any location of the track.

(20) iStable To reduce the jolt in the recorded video.(also see Chapter 7.1)

(21) Add Setting Include the new setting to the temporary setting block.

(22) Rename Change the name of the selected setting in the temporary setting block.

(23) Delete Permanently remove the selected setting in the temporary setting block.

(24) Load Setting Call the saved settings.

(25) Save Setting Store the settings in the temporary setting block.

7.1 To Use iStable The iStable function can reduce the jolt in the recorded video. 1. Click Open File button and select the recorded video. 2. And then, click iStable button. 3. iStable windows will show up. 4. Select the smoothness level – 1(Low),

2, 3, 4, and 5(High). The default value is 3.

5. Click Play button, and then iStable function will start to initial the recorded video.

6. When the initialize is done, user will see the original and stabilized recorded video play in two windows.

40

Chapter 8 Using the Remote Programs User can use Microsoft Internet Explorer to access DVR system by entering the IP address. To use this feature, make sure that you PC and EB 1304 NET both are connected to the internet and the Network feature is enabled. Accessing this feature for the first time you will be prompted by your browser to install WebCamX.cab, allow the installation and you should be able to connect and login afterwards. For Windows 2000, click Yes when the Security Warning dialog box appears.

For Windows XP, click Install when the Internet Explorer - Security Warning dialog box appears.

After installing the WebCamX.cab and when connecting to the DVR system, you are required to enter User ID (Superuser or User) and password (default password is 111111) and select the type of network. Superuser has the authority to remote setup the DVR system configuration on Web Viewer.

i

- If user can not connect to DVR server, it might be the IP address of DVR server is conflict with IP address of any PC at network. Please contact the manager of DVR server to reconfigure IP address of DVR server. Please reconnect with DVR server again when the IP address conflict is solved

- Changing the Superuser and User default password is strongly recommended.

41

8.1 Familiarizing the Web Viewer Buttons Right-clicking on the Web Viewer video screen, enables you to start video recording, change video quality, switch camera and enable/disable DirectDraw.

(10)

(8)

(9)

(7)

(6)

(5)(4)(3)(2)(1) Name Function

(1) DirectDraw Enhance the video quality.

i

Not all graphic cards can support this function. If you can not see the screen display correctly or screen is messed, please check with VGA card vendor.

(2) Received file size Indicate the size of the data being sent per second.

(3) Camera frames Indicate the number of frames per second.

(4) Split screen view Select the display screen mode to view

(5) Record Start to record the video of the selected camera in AVI format. Directly click screen to select the channel that user wants to record and press Record button.

(6) Remote Console Initiate Remote Console. It allows you to control DVR server (see also Chapter 8.2).

(7) Remote setup Change the DVR server settings (see also Chapter 8.1.1).

i

Only Superuser has the authority to remote setup DVR system.

(8) Snapshot Capture and save the screen shot in *.bmp format.

(9) Full screen Use the entire area of the screen to only display the video. To return, Right click the mouse or press ESC on the keyboard.

42

Name Function

(10) Select cameras to view

Select to the view camera from different server. In Select Camera dialog box, Display column, click to enable/disable viewing the camera. Click Add Server and select the server type between DVR and IP Cam to add. Click Delete Server to delete the selected item. Click Import to load the previous saved list. Click Export to save the list. Click Apply All to change all the camera video quality based on the selected setting. Click OK to exit.

43

8.1.1 To Setup Remote System Setting Click OK to exit and save the setting and Cancel to exit without saving the setting. The setting here applies to Remote DVR only.

i

After changed the DVR system setting, refresh your web browser in order to apply the new setting to the DVR system.

8.1.1.1 System Setup

(1)

(2)

(3)

(1) Audio mute

Enable/disable to hear audio sound of local DVR. To hear sound, make sure the unit is connected to an audio output device (ex: speaker). If user recorded video in audio mute status, there is no sound when playback

(2) NTP Setting Setup the time auto synchronization. - Enable NTP

Enable/disable time synchronization automatically through network. The DVR system will auto synchronize time from NTP servers which user has entered in following server 1 and server 2 column. The first time synchronize will be 6 hours later after system power up.

i

When the daylight saving is enabling, the auto time synchronization will be stopped.

- TIME ZONE: Select the time synchronization time zone. The time zone will base on GMT (Greenwich Mean Time) time zone.

- Server 1/Server 2 Fill in the network time server URL or IP address (clock.stdtime.gov.tw or time.stdtime.gov.tw)

44

(3) DLS Setup daylight saving settings. - Enable DLS

To enable/disable daylight saving function. - START

Setup daylight start up date and time. - END

Setup daylight stop date and time. - TIME OFFSET

Assign a time that it is for daylight saving time offset in your time zone. For example: if the time zone is in U.S. Eastern, the time offset is 1 hour.

8.1.1.2 Camera Setup

(1)

(2)

(3)

(4)

(1) Camera Select:

Enable/disable the channel number to display the video on the surveillance screen (2) Auto Scan

Enable/disable auto cycle switch to display the next channel when in full screen preview. (3) Camera Name

Assign a name for the channel (4) Video Adjustment

Select the camera and adjust the Brightness, Contrast, Hue and Saturation of the selected camera. - Default Value: Set the video value back to default

45

8.1.1.3 Record Setup

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(1) Record Select

Enable/disable the channel number to record video

i

The channels which could be recorded should be enabled in the CAMERA SELECT first.

(2) Record Mode Select D1/CIF recording mode. Under D1 mode, the video recording is in full screen resolution. Each channel is recorded at a maximum frame rate of 15fps. You can switch to view the video in single full screen or 4 split screen. Whereas in CIF mode, video recording is at a lower resolution, but each video is recorded in 30fps/25fps (NTSC/PAL).

(3) Record Frame Rate Set the number of frames per second to be recorded. Refer to the table below for the available record frame rate settings. The higher the frame rate is, it uses more hard disk space

Video Standard

Record Mode NTSC PAL

D1 60, 20, 4 48, 20, 4

CIF 120, 60, 40, 20, 4 100, 48, 20, 4

(4) Video Quality Select the video quality setting from BEST, HIGH, MEDIUM, GOOD, NORMAL or LOW.

(5) Auto Record Enable/disable auto continue recording when interrupted (i.e., power breakdown, video playback or configuration setup). It continue recording after 10 second of idleness. This

46

is applicable in Always Record mode under schedule setting. (6) Audio Record

Enable/disable audio recording. To record sound, make sure the microphone is connected to the unit

(7) Disk Overwrite Enable Enable/disable replacing the earliest record when the hard disk space runs out. By default, the HDD overwrite setting is enabled

(8) Motion Detection - Motion Camera

Enable/disable the channel number to detect motion. - Motion Record Time

Set the amount of time (in second) to record when a motion has detected. - Sensitivity

Set the sensitivity level. The sensitivity is from high, 9~ 2 and low.

47

8.1.1.4 Alarm/Sensor Setup

(1) (2)

(3)

(1) Sensor Setup

- Sensor Status Customize the initial state of the attached sensor for every camera. Refer to the table below to customize the sensor state. Not installed: Indicates that there is no sensor connected Normal open: Indicates that the initial state of the sensor is normal open. Video

recording initiate when there is a changes in the sensor state

Normal close: Indicates that the initial state of the sensor is normal close. Video recording initiate when there is a changes in the sensor state

- Sensor Record Time Set the amount of time (in second) to record after the sensor has been triggered

- Alarm Out Time Set the amount of time (in second) to continue sending the alarm once activated

- DVR Video Loss Alarm Enable/disable the alarm when channel video is lost. Select the channel for video alarm loss.

(2) Mail Alarm Setup Enable/disable alarm sending mail when alarm has triggered at the selected condition. - HD Fail Alarm: Issue an alarm when hard disk of DVR system is failed. - Motion Alarm: Issue an alarm when the selected channel has been detected the

48

motion.

i

The Motion Detection must be enabled first, the alarm sending mail will send out the mail when detect motion.

- Sensor Alarm: Issue an alarm when sensor of selected channel has triggered. - Video Loss: Issue an alarm when t selected channel’s video is lost. - E-Mail Setup

SMTP: Enter the SMTP server User ID & Password: Enter User ID and Password for e-mail server user

identification From: Enter the sender e-mail address To: The recipient e-mail address and separate it with a semicolon Subject: Enter the message title Message: Type the message

- Mail with picture: When send out alarm mail will include a capture image of alarm

channel.

(3) CMS Alarm Setup Enable/disable alarm mail sending to CMS (Central Management System) when alarm has triggered at the selected condition. - HD Fail Alarm: Issue an alarm when hard disk of DVR system is failed. - Motion Alarm: Issue an alarm when the selected channel has been detected the

motion.

i

The Motion Detection must be enabled first, the alarm sending mail will send out the mail when detect motion.

- Sensor Alarm: Issue an alarm when sensor of selected channel has triggered. - Video Loss: Issue an alarm when t selected channel’s video is lost.

49

8.1.1.5 Network Setup

(1)

(2)

(3)

(1) IP Mode

- Static IP Assign a fixed and global IP address for the DVR system. Fill in the columns of Static IP section. IP: Assign a constant IP address which real IP addresses give from ISP. Mask: Enter the subnet mask of the IP address which user has assigned to DVR system.

i It is a bitmask used to tell how many bits in an octet(s) identify the subnetwork, and how many bits provide room for host addresses.

Gateway: Enter the network gateway IP address DNS: Domain Name Server translates domain names (such as www.abb.com.tw) to IP addresses. It will translate the domain name into IP address when DVR system request.

- DHCP Assign the IP address by local DHCP server to DVR system.

i The Dynamic Host Configuration Protocol (DHCP) is a set of rules used by a communications device (such as a computer, router or networking adaptor) to allow the device to request and get an Internet address from a server which has a list of addresses available for assignment.

- PPPOE Point-to-Point Protocol over Ethernet is a network protocol for encapsulating PPP frames in Ethernet frames. It is used mainly with ADSL services. Fill in the columns in PPPOE section.

(2) Option - Remote Audio Record: Enable/disable audio recording when recording at remote

site. - Server Port: A port is using for the remote connection. Any port can be assigned as a

server port, except the ports already used by the network services.

50

- UPNP Enable: Enable/disable UPnP function that can automatically configure the port setting to the local router.

- UPNP Port: Assign a port for UPNP service using. (3) DDNS

DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating domain names into Internet addresses. Users can register their own domain name on http://ddns.avers.com.tw. (See Appendix A) - Domain Name

Enter the domain name that user has registered. - Auth Key

A password use to access DDNS that user has setup when register the domain name.

i - To register a domain name, please refer to Appendix A. - Please restart DVR system in order to active DDNS service.

51

8.1.1.6 Password Change

Click Remote setup button on Web Viewer main interface, and then, click User button to call out the Password Change interface.

(1)

(2)

(1) Superuser

Change the remote accessing password of super user. Superuser has the authority to remote setup the DVR system configuration on Web Viewer. - Password

Enter the new password - Password Confirm

Re-enter password to confirm (2) User

Change the remote accessing password of user - Password

Enter the new password - Password Confirm

Re-enter password to confirm

52

8.2 Familiarizing the Remote Console Buttons

(1) (3) (7)(6)(5)(4)

(8)

(9)

(11)(12)

(2)

(10)

(13)

Name Function

(1) Exit Close the Remote Console.

(2) Audio button Enable/disable the sound.

(3) Split Screen Mode Select from 2 different split screen type to playback the recorded video file of all the camera, or one camera over the other or alongside on a single screen.

i

- If there are only 4 cameras, you won’t be able to switch to 9, 16, and 13 split screen mode. - To change the video quality, right-click on the screen and select between High, Normal or

Low.

(4) Record Start/stop video recording.

(5) Network Enable/disable remote system access. This feature allows you to access EB DVR server from a remote location via internet connection.

(6) Setup Configure the Remote Console setting. (see also Chapter 8.2.1)

(7) Preview Switch to Preview/Playback mode. This allows you to view live camera display.

(8) Playback Switch to Playback mode. This allows you to view the recorded video file. (see Chapter 8.3)

(9) Status Bar Display the current date, time and hard disk free space.


(11) Snapshot Capture and save the screen shot either in *.jpg or *.bmp format.

(12) Full screen Use the entire area of the screen to only display the video. To return, Right click the mouse or press ESC on the keyboard.

(13) DirectDraw Enable/disable DirectDraw function

i

Direct Draw function supports for certain VGA card. For more information, please contact your VGA card vendor.

53

To Setup Remote Console Setting Click Setup button to call out the System Setting windows. Click OK to exit and save the setting and Cancel to exit without saving the setting.

(1)

(1)

(1)

(1)

(1) Storage Path

Set the directory on where to save the data. When there is not enough free space to record one hour data, the system automatically replaces the oldest data. In case you have more than one storage path, the system automatically saves the data to the next storage path. By default the data is stored in C:\RemoteData, to insert another storage path, click Add. To remove the selected path, click Delete. - Enable network storage

Select the Enable network storage check box to send the recorded video in network-attached storage.

i

To add network storage, the Internet storage drive/folder must be mapped as Network Driver in DVR server. To know how to assign or connect to a network drive, please refer to your Windows help file and search “Map Network drive”.

(2) Language Customize the system to display the tool tips and dialogs based on the selected language. By default the language is in English.

(3) Remote Server Enter the DVR Server IP and Server Port number.

(4) Channel Settings The numbers from 1 to 4 represent the camera ID. In Transmitting Channels section, enable the camera number to receive the camera signal from the server. In Visible Channels section, enable the camera number to view the camera signal on Remote Console screen. To select all the cameras, enable the ALL check box.

54

8.3 Using the Remote Playback To use this feature, first you need to select the source of the file. Click the Playback button. And then, in the Select Playback Mode dialog box, choose Local Playback to open the file that is recorded in the Remote Console, and Remote Playback to open the file that is recorded in the DVR server. When you choose Remote Playback, select Download and Playback.

Click OK to proceed and Cancel to void this operation.

In the Video Playback Date/Time Selection, the number from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 16 represent the camera number.

To Make a Selection: 1. Select the date in the calendar. Use and buttons to shift the calendar to the left

or right. 2. In the table below, click on the blue block to select and open the recorded file. The blue

block turns red when it is selected. The block that appears in white doesn’t have data.

55

You can only select one block when you choose Download and Playback.

3. Click OK to proceed and Cancel to void this operation.

4. If you select Download Playback and after making the selection, the system divides the selected hour into 16 video thumbnails. In the Time Selection screen, click on the video thumbnail you want to download (see also Chapter 8.3.2).

8.3.1 Familiarizing the Local Playback Buttons

(1)(2)

(4)(3) (5)(6) (7)

(8)

(9)

(12)(11)(10)

(13)

(14)

(15)

(16)

Name Function

(1) Split Screen Mode Select from 2 different split screen type to playback the recorded video file of all the camera, or one camera over the other or alongside on a single screen.

i

- If there are only 4 cameras, you won’t be able to switch to 9, 16, and 13 split screen mode. - To zoom in an area on the screen, Right click and Drag a square on the area you want to

enlarge. To back to normal view, right click the channel screen again.

(2) Exit Close the application

(3) Progress bar Show the progress of the file being played. You may move the bar to seek at any location of the track.

(4) Hour Buttons Select and click to playback the recorded video file on the specific time frame.

i

The Hour buttons represent the time in 24-hour clock. The blue bar on top of the hour button indicates that there is a recorded video file on that period of time. If there is no recorded data within the hour, there will be no color bar on top of the hour button. While the red bar indicates that you are currently viewing the recorded video file.

56

Name Function

(5) Playback Control Buttons

Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of ½x, ¼x, or ⅛x. Rewind: Wind back the video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, or 8x. Next: Go to the next frame. End: Go to the end of the video file.

(6) Date Select the date on the calendar and the time from 00 to 23 to where to start playing the recorded video file.

i

The numbers from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 16 represent the camera ID. While the red colored column indicates on where to start playing the recorded video file. If there is no any video data, it will be no color bar on top of the date button.

(7) Preview Switch to Preview/Playback mode.

(8) Playback Switch to Playback mode. This allows you to view the recorded video file.

(9) Status bar Display the record date, time, HDD capacity in preview mode and play speed in playback mode.


(11) Export Export includes Snapshot, Print, and Output Video Clip function. Snapshot: Capture and save the screen shot either in *.jpg or *.bmp format. Print: Print the screen shot. Output Video Clip: Save the segmented file in *.mpg, *.avi, or *.dvr

format.(see also Chapter 8.3.2.1). (12) Segment Keep a portion of the recorded video you want (see also Chapter 8.3.2.1).

(13) Full screen View in Playback-compact mode. To return, press the right button of the mouse or ESC on the keyboard.

(14) Visual Search Search from a specific camera by Date, Hour, Minute, 10 Seconds and Second.(see also Chapter 8.3.2.2)

(15) Find Next Search for the next event or changes in the motion detector frame. You can use this when you are using Intelligent Search or Event Search function.

(16) Intelligent Search Search the changes in the motion detector frame (see also Chapter 8.3.2.3)

57

8.3.2 Familiarizing the Download and Playback Buttons

(2)

(1)

(3)

(5)(6)

(8)

(4)

(7)

Name Function (1) Exit Close the application (2) Progress bar Show the progress of the file being played. You may move the bar to seek at any

location of the track. (3) Playback

Control Buttons

Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, or 1/8x. Rewind: Wind back the recorded video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, or 8x, 16x or 32x. Next: Go to the next frame. End: Go to the end of the recorded video file.

(4) Status bar Display the recorded date, time and play speed. (5) Export Export includes Snapshot, Print, and Output Video Clip unction.

Snapshot: Capture and save the screen shot either in *.jpg or *.bmp format. Print: Print the screen shot. Output Video Clip: Save the segmented file in *.mpg, *.avi, or *.dvr format.

(6) Segment Keep a portion of the recorded video.(see also Chapter 8.3.2.1) (7) Full screen View in Playback-compact mode. To return, press the right button of the mouse or

ESC on the keyboard. When you switch to full screen in multiple-screen mode, Left click to toggle to only display one of the video in the multiple-screen mode or all.

(8) Visual Search Search from a specific camera by Date, Hour, Minute, 10 Seconds and Second.(see also Chapter 8.3.2.2)

58

8.3.2.1 To Cut and Save the Wanted Portion of the Recorded Video 1. Use the Playback Control buttons or drag the bar on the playback progress bar and

pause on where you want to start the cut. Then, click Segment to set the begin mark.

2. Use the Playback Control buttons or drag the bar on the playback progress bar and

pause on where you want to end the cut. Then, click Segment to set the end mark. To cancel segmentation or set the segment marks from the start, click Segment button again.

3. Click Output button to save the wanted clip. 4. In the Save As dialog box, locate on where you want to save the file, type the filename,

and select the video format.

8.3.2.2 To Search Using the Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the date. Then

click OK.

3. When a series of frames appear by date, click on the frame to display another series of

frames and search by every Hour of that date, every 3Minutes of that hour, every 10 Seconds of that minute, every Second of that 10 seconds. To go back, click . To view from the selected frame and close event search, click .

59

8.3.2.3 To Search Using the Intelligent Search 1. Click on the video screen on where you want to search. 2. Click Intelligent Search. The Intelligent Search text (red) would appear at the lower left

corner of the screen.

Intelligent Search

3. When the Intelligent Search Setting dialog box and motion detector frame appear, you

may adjust the sensitivity bar and the motion detector frame size and location. To set motion detector frame size and location, left click and drag on the screen. Then, click OK to start searching. The video search would stop at the frame that matches the condition. To keep on searching click .

4. You may also set to search and list all the result. Just check the List box. In the Search Duration section, set the Begin Time, End Time and Searching Interval. Then, click OK to start searching.

60

Chapter 9 Using HandyViewer to Access DVR server

Users can use a mobile phone to access the DVR through Internet. Make sure your mobile phone support IE browser and is connected to the internet. To access the DVR server, open IE browser and enter http://enter server IP or domain name here/mobile. You can see the latest screen shot. Click << >> to change the channel or camera and Refresh to reload new screen shot.

9.1 Using PDA Viewer to Access DVR Server Users can also use a PDA to access the DVR through Internet. Make sure your PDA support IE browser and is connected to the internet. To use this feature, you need to install the PDAViewer software either thru ActiveSync connection or download it from the internet. Please check if your PDA meets the 2 requirements below.

OS: MS Windows CE 4.0, PocketPC 2002/2003, Mobile 5 PDA version

CPU: ARM architecture

9.1.1 To install PDAViewer thru ActiveSync 1. Connect your PDA to your PC. Place the CD into the

CD-ROM drive then click Install PDAViewer. And follow the on screen instructions.

2. Click Next to continue.

3. Read the license agreement and click Yes to accept all

the terms. The system will then automatically install the application.

4. When you are prompted, click Yes to install the

application using the default directory.

61

5. When done, click OK.

9.1.2 To install PDAViewer from the Internet Make sure you are connected to the internet. 1. Open the web browser and enter the server IP. Then click

the hyperlink Download PDA-Viewer.

2. When the Download dialog box appears, enable Open

file after download and click Yes.

After the installation, the PDAViewer icon will appear in the Programs list.

62

9.1.3 To Use the PDAViewer 1. Run the PDAViewer in the Programs. 2. Familiarizing the PDAViewer buttons.

(7)(6)

(5)

(3)(4)

(8)(9)

(10)

(1)(2)

Name Function (1) Connect Hook up to the DVR server. Make sure you are connected to internet.

When the iView screen appears, click Add to add DVR server.

Enter the server IP, port, user ID, password and select the connection type. Then, click OK.

User can playback the recorded video from remote DVR server in PDAviewer.(see Chapter 9.1.4)

(2) Split Screen Mode Select between 2 screen display types. It also allows you to switch and view different camera number or channels.

(3) About Display the PDA-Viewer software version. (4) Minimize Reduce the size to taskbar. (5) Exit Close the PDA-Viewer. (6) Focus Adjust the focus of PTZ camera to produce clear image. (7) Full Screen Use the entire screen to only display the video. (8) Snapshot Capture and save the screen shot in *.bmp format. (9) Zoom Zoom in and out the PTZ camera image. (10) Direction buttons Adjust and position the focal point of the PTZ camera.

63

3. To change the video quality, enable/disable audio, and select to display different camera, tap on the video screen longer the pop up menu will appear.

9.1.4 To Playback in PDA Viewer 1. Run the PDA-Viewer in the Programs. 2. Hook up to the DVR server. 3. Click Connect icon and select the DVR server 4. Click Playback to enter playback option screen 5. Select the camera, data, and time 6. Click Playback to start playing the recorded video

7. While playback, user can view and change status of I/O devices 8. On the playback screen, tap on video screen longer the pop up menu will appear 9. Select the Remote IO

10. The sensor and relay devices will list as below:

64

11. User can change the relay status. Select the relay and tap on video screen longer the

pop up menu will appear, and then, select the status (ON, OFF, Trigger)

9.2 Using JavaViewer to Access DVR Server Using the mobile phone within Symbian Smart Phone OS to access the DVR through Internet. Make sure your mobile phone supports Symbian Smart Phone OS and can be connected to the internet. To use this feature, you need to install the JAVAViewer program that it can be downloading it from the DVR server through the internet. To install JAVAViewer from the DVR Server 1. Open the web browser and enter the DVR server IP (http://DVR server IP:

port/JAVA-Viewer.html). Then click Connect. 2. When the Download screen appears, select JAVA-Viewer.jad and download it to your

mobile phone. 3. After the installation, the JAVAViewer will be in your mobile phone system. To find the

JAVAViewer program where is located, please refer to your mobile phone user’s manual.

- DVR server only provides one channel video at time and transmits one frame per

second to JAVAViewer. - When there is a multiple JAVAViewer connection, DVR server will transmit the last

JAVAViewer’ request to all JAVAViewers. - Please assign the port that besides port 80 as JAVAViewer video port.

65

9.2.1 To Use the JAVAViewer 1. Run the JAVAViewer program.

2. Enter the DVR IP address, port number, user ID, and

password. Please refer to your DVR server setting for that information.

3. And then, select the Connect to connect to DVR server.

4. Click Yes to accept the data from DVR server.

5. When connection is success, you will see the camera

video on the screen.

6. To switch to different camera view, select menu and

select the channel.

7. The JAVAViewer support PTZ control function, you can

refer to Help file for detail function control key. Select menu and go the way down to select the Help file.

→

66

Appendix A Registering Domain Name DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating domain names into Internet addresses. It allows remote clients to intelligently search dynamic servers without any previous enquiring for servers’ Internet addresses. In order to take advantage of this intelligent service, first register your domain name on the following Web site http://ddns.avers.com.tw 1. User Login

- Browse the website ddns.avers.com.tw with Microsoft IE or Netscape Navigator to access the following dialog.

- First input the MAC address of your DVR system as CD-Key number and select the

product name. The CD-Key of MAC address input format shall be 12 digits without colon (:) or hyphen (-).To find MAC address of your DVR system, follow the steps below: • In OSD menu, select NETWORK SETUP • Select any one of IP mode • A NETWORK INFORMATION windows will show up • MAC address of DVR system is display as shown

- Then click OK to login or Reset to clear the previous input. 2. User Information

Please provide the following user information, Host Name (user can choose any name he/she likes except the one violence with other users), Password, E-mail, Company, and Country. And then, click OK to complete the domain name registration.

67

Appendix B Network Service Port The following table shows the ports that DVR server uses for certain network service.

Port # Variable Remote Console (CM 3000)

5550 Y

WebCam 80 Y 2-way audio 9999 Y Remote Control (CM3000/RC1000)

5555 Y

DVR POS 5150 Y DVR DDNS (Upload / Download)

53 / 1053 N

Warranty Notice

LIMITED WARRANTY

AVerMedia TECHNOLOGIES, Inc. warrants this product to be free of defects resulting from faulty manufacture or components under the following terms:

WARRANTY LENGTH

Labor is warranted for (1) one year from the date of purchase

Parts are warranted for (1) one year from the date of purchase

Replacement products will be warranted for the remainder of the one year warranty period or (30) thirty days, whichever is longer

WHO IS PROTECTED

This warranty is enforceable only by the first consumer purchaser

WHAT IS AND IS NOT COVERED

Except as specified below, this warranty covers all defects resulting from faulty manufacturing of this product. The following are not covered by the warranty.

1. Any product on which the serial number has been defaced, modified, or removed

2. Damage, deterioration, or malfunction resulting from:

Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, commercial or industrial use, unauthorized product modification, or failure to follow instructions included with the product.

Misapplication of service by someone other than the manufacturer’s representative

Any shipment damages (Claims must be made with carrier)

Any other cause which does not relate to a product defect

3. Cartons, cases, batteries, cabinets, tapes, or accessories used with product

4. AVerMedia does not warrant that this product will meet your requirements; it is your responsibility to determine the suitability of this product for your purpose

WHAT WE WILL AND WILL NOT PAY FOR

We will pay labor and material expenses for covered items. However, we will not pay for the following:

1. Removal or installation charges

2. Shipping charges

3. Any incidental charges

EXCLUSION OF DAMAGES

THE MANUFACTURER’S SOLE OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT AT OUR OPTION. THE MANUFACTURER SHALL NOT, IN ANY EVENT, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE (INCLUDING, BUT NOT LIMITED TO, DAMAGES RESULTING FROM INTERRUPTION OF SERVICE AND LOSS OF BUSINESS) OR LIABILITY IN TORT RELATING TO THIS PRODUCT OR RESULTING FROM ITS USE OR POSSESSION.

LIMITATIONS OF IMPLIED WARRANTIES

There are no other oral or written warranties, expressed or implied, including but not limited to those of merchantability or fitness for a particular purpose. Any implied warranties are limited in duration to one year from the date of purchase

STATE LAW AND YOUR WARRANTY

This warranty gives you specific legal rights, and you may also have other rights granted under state law. These rights vary from state to state

CONTACT INFORMATION Taiwan & International 5F No. 135, Jian Yi Rd., Chung Ho City, Taipei, Taiwan TEL: 886-2-2226-3630 FAX: 886-2-2226-7241 Web Site: www.avermedia.com / http://www.averdigi.com

avermedia averdigi eb1304net sata sata manual.pdfa: averdigi eb1304net sata unit b: averdigi...

Documents