audi rnsd
TRANSCRIPT
-
8/12/2019 Audi RNSD
1/84
Audi Navigation Plus Installation
Phase 1 (A6/S6/RS6/allroad)For Symphony I Head units (model year 1999.5 to 2001): GPS installation TMC/CAN installation and wiring to instrument cluster
For Symphony II Head units (model year 2002 2004): GPS installation Taping into the speed sensor, illumination and Ignition PowerSources from instrument cluster
TMC/CAN installation (wiring will come in Phase II)
Pictures: 1a 1n
1.
-
8/12/2019 Audi RNSD
2/84
Nav Plus - components and installation stuff
Copyright Ted Basile ( [email protected] )
1a.
Updated: 7/19/2004
Nav+ HU (Audi Part#4B0-035-192H)
TMC/CAN Gateway and
mounting bracket(Audi Part# 4B1-919-894)
Lots of extra pins/wires etc(more than I would ever need)
Black hockey stick tapeand radio removal tools
GPS antenna ordered fromwww.gpsaccessories.com
Lots of extra connectors,pins/wires etc (more than I
would need)
2003/2004 D-Navi map disk set
-
8/12/2019 Audi RNSD
3/84
Nav Plus Installation Phase 1 (1999.5-2001 A6/S6/allroad Symphony I)(Homemade TMC/CAN Gateway harness)
2 Pins to Inst.Cluster GreyConnector to accessCAN H (Pin #5) andCAN L (Pin#6)
12 Pin TMC Connector (Audi#4A0-972-883)(Female pins with wiresAudi#000-979-003; only 6 are used)
Wrapped in hockey stick tape(very OEM-like)
Please note: There shouldbe two pins/wires (Audi#000-979-003) attached to
these wires.
4 Pins go to behindNav+ unit (CAN H & L to26 Pin; battery+ andground to black 8 pinconnector via ajumper/wire tap)
1b.
Please Note: In a Symphony I head unit, it will be necessary to use a harness like this one to access the CAN H/Lfunctions from the instrument cluster. In a Symphony II, you can access the CAN H and CAN L from the 20 pin
connector, pin 7 and 12, respectively.
Copyright Ted Basile ( [email protected] )
Radio Shack4 pin harness(Item#278-767B)
Updated: 11/19/2004
-
8/12/2019 Audi RNSD
4/84
Nav Plus Installation Phase 1(Removing the Instrument Cluster 2003 A6 pictured)
1c.
Copyright Ted Basile ( [email protected] )
Please Note: I highly recommend protecting your steering wheel and column by putting down blue painters tape. The
two bottom screws of the instrument cluster can dig into your steering wheel column as you are removing it.
Updated: 7/19/2004
-
8/12/2019 Audi RNSD
5/84
Remove these two philips head screws. FYI -They are on tight, so make sure you have thecorrect size Phillips head; you dont want tostrip that screw head.
To avoid scratchingyour steering columnmake sure to cover itwith blue painters tape.
Cluster will come out like this.Use a flathead screwdriver torotate-up the purple tab on theblue connector first. Do same
for grey and green connectors,in that order. Install in reverseorder.
With the cluster out, you should see the blue, greyand green Instrument cluster connectors.
1d. Nav Plus Installation Phase 1(Removing the Instrument Cluster)
Copyright Ted Basile ( [email protected] )
With the cluster out, you should see the blue, greyand green Instrument cluster connectors.
Symphony I Symphony II
Updated: 7/19/2004
-
8/12/2019 Audi RNSD
6/84
Nav Plus Installation Phase 1 (1999.5-2001 A6/S6/allroad Symphony I)(Adding two pins/wires to grey connector)
If you make a mistake, you canextract a pin with an exacto- knife or
a very small flathead screwdriver
Pins #5 (CAN High) and #6 (CAN Low) attach Audi part#000-979-003
Slide purple piece out towards you and theinner white harness will slide out.
1e.
Copyright Ted Basile ( [email protected] ) Updated: 7/19/2004
-
8/12/2019 Audi RNSD
7/84
Nav Plus Installation Phase 1 (2002-2004 A6/S6/RS6allroad Symphony II)(Taping into GALA, illumination, ignition)
Copyright Ted Basile ( [email protected] )
With the cluster out, you should see the blue, greyand green Instrument cluster connectors. In aSymphony II environment, the blue connector is theone you want
1f.
I used a pair of vise grips to hold back thePlastic shielding while we attached the 3Mbrand T wire taps.
The blue 32 pin connector:Pin#3 white/blue wire = GALA speed sensorPin#7 black wire = Ignition power(sometimes found in pin#1 as well)Pin#20 grey/blue wire = Illumination signal
Updated: 3/19/2005
-
8/12/2019 Audi RNSD
8/84
Nav Plus Installation Phase 1(Location of GPS antenna/receiver)
1g.
Using 2 Velcro strips, I attached my GPS antenna up inside the dash area (above the inst. Cluster). You cant see itfrom this location, but when you have the cluster out, you will notice a little cubby hole area where you can insertthe GPS. I put the Velcro strips down first, then wrapped my GPS in Velcro; its in there pretty tight. As forreception, I average 5 or 6 GPS satellites received most of the time (a minimum of 3 is needed).
As for the remaining wire, you can also wrap it in Velcro and stuff in that same cubby area. I decided to run the GPSwire (see G) in between these metal support pieces (not required for everyone else).
GG
GPS wire: leave yourself 3 feet of slackfrom here to behind your HU area.
GPS is located up hereusing Velcro strips.
Copyright Ted Basile ( [email protected] ) Updated: 7/19/2004
-
8/12/2019 Audi RNSD
9/84
-
8/12/2019 Audi RNSD
10/84
Copyright Ted Basile ( [email protected] )
Nav Plus Installation Phase 1(View of TMC/CAN gateway)
This bracket will beremoved to install theTMC/CAN underneaththe drivers sidedashboard of an A6
12 Pin Connector (AudiPart# 4A0-972-883)attaches here.
In Europe, these antenna connectorsare used to route the Traffic MessageChannel information into the Nav+.Not used in USA.
1i.
Please note: This is a 4B0 919 895B TMC device and doesnot offer CAN functionality. Both the 4B0 and the 4B1
versions have the 12 pin connector and some 4B0's have alarger 26ish pin blue connector as well.
Updated: 7/19/2004
TMC/CAN gateway(Audi part#4B1-919-894B)
-
8/12/2019 Audi RNSD
11/84
Nav Plus Installation Phase 1(Location of TMC/CAN gateway)
1j.
Copyright Ted Basile ( [email protected] )
In relation to your Nav+ head unit and your instrumentcluster, this is probably the best place to locate yourTMC/CAN gateway unit for a A6/S6/RS6/allroad.
My unit came with the OEM mounting bracket, but I found itvery difficult to fit into this area without doing a lot ofpermanent damage to the dash area. I spent over an hourtrying to make it fit with no success. Instead, I decided toremove the mounting bracket (see diagram 1h) with a TorxT7 or T8 wrench.
My solution was to attach it to one of the existing metalbraces inside the dashboard using large velcro strips (toreduce an future metal-on-metal vibrations) and large plasticelectrical zip ties. It is pretty snugand not going anywhere.
Please note: Make sure you are able to access your 12 pinconnector so you can easily plug it in later in the installation.
FYI - Steeringwheel column
Velcro strips to reduce potentialnoises
Heavy duty zip tiesare used to hold it inplace.
TMC/CANGateway
Updated: 7/19/2004
-
8/12/2019 Audi RNSD
12/84
Nav Plus Installation Phase 1 (1999.5-2001 A6/S6/allroad Symphony I)
This is where I ran my GPS wire and TMC/CAN harness prior to installing my TMC/CAN unit and removing mySymphony I head unit. Please note: With your Symphony HU removed, you only need to run the GPS wire and the4 pin Radio Shack connector. I would wrap both in electrical tap to avoid any metal-on-metal contact. Keep those
tucked away for Phase 2 of the installation.
Copyright Ted Basile ( [email protected] )
1k.
12 Pin TMC/CANconnector
4 pin Radio Shack
connector
GPS wire withSMB connector
2 wires going to
grey instrumentcluster connector
Updated: 7/19/2004
-
8/12/2019 Audi RNSD
13/84
-
8/12/2019 Audi RNSD
14/84
GPS antennas - OEM Roof Mounted Rod Style
Courtesy of Ted Basile ( [email protected] ) Updated: 7/19/2004
1m.
-
8/12/2019 Audi RNSD
15/84
Courtesy of Ted Basile ( [email protected] )
GPS antennas - OEM Roof Mounted Shark Fin Style
Updated: 7/19/2004
1n.
-
8/12/2019 Audi RNSD
16/84
Audi Navigation Plus Installation
Phase 2 (A6/S6/RS6/allroad)For Symphony I Head units (model year 1999.5 to 2001): Relocating pins from existing wiring harnesses and adding thenecessary wire jumpers
Making preparations for future audio/video inputs and devices
For Symphony II Head units (model year 2002 2004): Relocating pins from existing wiring harnesses adding thenecessary wire jumpers
Making preparations for future audio/video inputs and devices
Pictures: 2a 2p
2.
-
8/12/2019 Audi RNSD
17/84
Nav Plus Installation Phase 2(Removing Symphony I or II head unit using radio removal tools)
Copyright Ted Basile ( [email protected] )
These tools can be purchased on www.ebay.com or via www.samstagsales.com. The part number is T10057.
Updated: 7/19/2004
2a.
-
8/12/2019 Audi RNSD
18/84
-
8/12/2019 Audi RNSD
19/84
Nav Plus (Back of head unit) Phase 2
26 Pin Connector plugs in here
GPS Input via SMBconnector (a 90angle ispreferred)
Brown groundConnector (notused in Sym II)
Unique 10 Pinaudio/video input (ANexxtel or Dietz interfacewill convert this to RCA-
style A/V inputs Yellow/Red/White)
20 Pin Connector I
AM/FM Antenna inputs. Sym I uses both; Sym II(2002+) only uses the one on the left.
Copyright Ted Basile ( [email protected] )
8 Pin Connector II
8 Pin Connector III
Updated: 11/19/2004
2c.
-
8/12/2019 Audi RNSD
20/84
Used for removing the female pins
from 20 pin Connector I (approx. $90)
Used for removing the female pins from
8/10 pin Connector II, III and IV (approx. $90)
Nav Plus - Phase 2(Audi/VW wire extraction tools - very useful, but not necessary)
Courtesy of Ted Basile ( [email protected] )
Please note: I have purchased both of these tools andcan lend them to anyone in the United States. Feel freeto contact me at [email protected] .
Updated: 7/19/2004
2d.
-
8/12/2019 Audi RNSD
21/84
Nav Plus Installation Phase 2(Wire taps 3M T-style taps or Quickslide connectors)
Courtesy of Ted Basile ( [email protected] )
or
Please note: The T-style wire taps are preferred by most stereo installation shops because you can easily removethe male blade connector from the tap. Whether you use the T-style or quick slide kind, you should use an Exacto-knife or some kind of razor blade to strip away some of the wire insulation. You want to make sure you have goodcontact to the wire.
Updated: 7/19/2004
2e.
-
8/12/2019 Audi RNSD
22/84
Nav Plus Installation Phase 2(The Female 20 pin connector for Symphony I and II)
20 pin (Connector I) split into three distinct sections:- Blue: 8 pins for OEM CD Changer, PhatBox or Blitzsafeinterface etc.- Green: 6 pins for various functions (CAN H, CAN L etc)- Yellow: 6 pins for line-level output to Bose oraftermarket amplifier
20 pin (Connector I) typically found as one unit:I relocated the pins to the blue/green/yellow versionand taped back the pins that werent applicable forthe Nav+ conversion. This way, I dont cut any wires
and can reinstall my Symphony unit if need be.
There are clips on theother side of theseholes that allow youto slide theseconnectors off fromeach other.
Copyright Ted Basile ( [email protected] )
Please note: Stahwille tool# 1556 (female pins of20 pin) and 1591 cover the smaller and largerterminals. They cost $90 (purchased fromwww.asttool.com) each but can be borrowed
from me to switch your pins over.
Youll need to remove this yellow locking bar in connectors II, IIIand IV (use an exacto-knife or razor blade) before removing anyfemale pin. In connector I, you only need to slide a purple lockingbar out a bit. FYI youll still need a special tool to do this (seediagram 2i).
Updated: 7/19/2004
2f.
-
8/12/2019 Audi RNSD
23/84
Nav Plus Installation Phase 2(Symphony I vs II wiring differences)
Copyright Ted Basile ( [email protected] )
Illumination wire not presentin Sym II (look for grey/bluewire in dash area or behindinstrument cluster (anygrey/blue wire will do)
CD Ground CD GND wire presentonly in the 20 pin connector (pin#10)
GALA Speed sensor wire notpresent; need to find itbehind instrument cluster
Symphony II Diagram
Ignition/Power+ wire not present.
Youll need to tap into one underthe dash area or behind inst. cluster
Symphony I Diagram
Alarm Ground not used in Sym
II to Nav+ conversion.Telephone mute can beaccessed from this connectionbehind the Nav+ head unit
CAN H and L do not need to be accessedfrom behind the instrument cluster
Updated: 7/19/2004
2g.
-
8/12/2019 Audi RNSD
24/84
Reverse Wire
(optional)
CAN H & L fromInstr. Clstr. Harness
JumperNew wireNo changeNot used
Key
Symphony I (1999.5-2001 A6/S6/allroad) to Nav Plus Wiring Diagram
Copyright Ted Basile ( [email protected] )
2h.
Speed SensorSwitch Optional(if adding video
input)
Updated: 7/19/2004
-
8/12/2019 Audi RNSD
25/84
Reverse wire
(optional)
JumperNew wireNo changeNot used
Key
Symphony II (2002-2004 A6/S6/RS6/allroad) to Nav Plus Wiring Diagram
Copyright Ted Basile ( [email protected] )
GALA/Speed Sensor,Illumination and ignition
wires from behindinstrument Cluster
2i.
Speed SensorSwitch Optional(if adding video
input)
Connector II is usually not
present in 2002+ A6/S6/RS6/allroad
Connector IV is
usually notpresent in
2002+ A6
Updated: 8/4/2004
-
8/12/2019 Audi RNSD
26/84
-
8/12/2019 Audi RNSD
27/84
Nav Plus Installation Phase 2(OEM CD changer cable and auxiliary audio input options)
Courtesy of Ted Basile ( [email protected] )
Blitzsafe Adaptor (part# AUDI/AUX DMX V.1B) will work with the Audi
Navigation Plus. You can also purchase a version with a specificaudio interface to Pioneer, Alpine, Kenwood etc aftermarket XM
radios etc.
Precision Interface Electronics BLAU/8-RCA auxiliary input adapter.The 13" adapter cable has an 8-pin female connector at one end that
connects to the back of the receiver.
Pins 13-20 (Audi Part#4A0 972 643B) If you replaceyour one piece 20 pin connector with theyellow/green/blue 3-piece version, it will simplifyadding one of these input connectors.
If you have a 1999.5-2001, then you have the prewiringfor the OEM CD changer. In 2002-2004, Audi stoppedproviding the pre-wiring for a trunk-mounted CD changer.The Audi part# for this is 4B0-051-735B
If you install the BlitzSafe
Adaptor, you can remove thegreen and yellow portions of
this connector and use the blueconnector in your existingyellow/green/blue 20 pin
connector. There really isnt alot of space to spare behind the
Nav+ in a A6/S6/RS6/allroad
Updated: 7/19/2004
2k.
-
8/12/2019 Audi RNSD
28/84
US-Based Navigation Components
Youll notice the same kind of connectorshere that youd see behind a Symphony I or
II head unit.
The US-based navigation unithas the same kind of GPSinterface (SMB connector) as
the Nav+.
Please note: This picture is meant to describe how someone could use the GPS antenna from their existingnavigation system (US-based) for a Nav+ upgrade. This is not meant to show how to add the US-based navigationoption. To the best of my knowledge, I dont think anyone has performed this particular upgrade.
Courtesy of Ted Basile ( [email protected] ) Updated: 7/19/2004
2l.
-
8/12/2019 Audi RNSD
29/84
Nav Plus Installation Phase 2(Sym I to Nav+ Plug and Play wire harness Not used)
Copyright Ted Basile ( [email protected] )
Radio Shack Extension PowerCable (part#278-767B) - plugsinto custom TMC/CAN harness
The hard to locate 20 pin male connector (search ebay.de under Mini-
ISO connector) or can be sourced fromhttp://www.logjamelectronics.com/pieaashar.html Model# AARHAR.
Rocker switch (Radio Shack cat#275-693) from pin#1 (connector III)GALA speed sensor wire (optional).
26 Pin Connector, specific to Nav+ headunit (Audi part#3B0-919-754; femalepins/wires Audi part# 000-979-010)
Male 8 and 10 pin connectors
(Scosche VW01 Part#SCOVW01B www.sounddomain.com )
Female 8 pin (black & brown) andfemale 20 pin (blue/green/yellow)
connectors that would plugdirectly into Nav+ unit.
Reverse wire left openif/when I decide to locate it
Radio Shack 2 conductorAccess Cable (part#270-026).
Please Note: Because of the limited space behind the Sym I head unit and climate control, I was unable to use thisharness. I was able to plug it in and it worked perfectly. However, it might work in an B5/B6 A4/S4 or D1/D2 A8/S8.
Updated: 7/19/2004
2m.
-
8/12/2019 Audi RNSD
30/84
Nav Plus Phase 2 (another view)(Plug and Play wire harness Not used)
Copyright Ted Basile ( [email protected] )
Please Note: Because of the limited space behind the Sym I head unit and climate control, I was unable to use thisharness. I was able to plug it in and it worked perfectly. However, it might work in an B5/B6 A4/S4 or D1/D2 A8/S8.
Rocker switch to be mounted underdrivers dash area.
Updated: 7/19/2004
2n.
2
-
8/12/2019 Audi RNSD
31/84
Courtesy of Ted Basile ( [email protected] )
Nav Plus Installation Phase 2 Connectors/Pins
Updated: 7/19/2004
26 Pin Connector and female wire/pin
20 Pin Connector (blue/green/yellow version) and female wire/pin
2o.
Audi Part#:4A0 972 643B
Audi Part#:4A0 972 643A
Audi Part#:4A0 972 643
Audi Part#:000 979 131
Audi Part#: 3B0-919-754 Audi Part#: 000-979-010
2
-
8/12/2019 Audi RNSD
32/84
Courtesy of Ted Basile ( [email protected] )
Nav Plus Aftermarket Plug and Play wiring harness
Updated: 11/19/2004
2p.
Please Note: This connector will simplify your installation. In pre-2002 A6s, the wiring is a closer match correspond because this
was built for a non-CANbus environment. In a 2002-2004 A6s (which run on a CANbus), youll need to modify this harness toroute illumination, ignition power and speed sensor/GALA information from the instrument cluster. Also, please note that spaceis at a premium behind your A6 dash area, and adding this harness will make it difficult for you to push you Nav+ intoplace. Available at www.vwnavi.com, www.nav-plus.comor www.ebay.de
Male harness plugs into yourexisting wiring harness
26 pin connector.Female pins with wiresAudi part# 000-979-010
Toggle switch for A/V
Female harness (plugs into yourNav+). 8 pin Female pins with wiresAudi part#000-979-133.
3
-
8/12/2019 Audi RNSD
33/84
Audi Navigation Plus Installation Phase 3 (A6/S6/RS6/allroad)
Video Interface
For Symphony I and II head units (model year 1999.5 to 2004): Removal of driver and passenger side lower dashboard Installation of Nexxtel interface and Blaupunkt ME3 DVD/CD/MP3Player into glove box area
Pictures: 3a 3v
3.
3a N Pl Ph 3
-
8/12/2019 Audi RNSD
34/84
Using an 8MM socket wrench youll need to unscrew the following screws to be able to remove thelower dash. I recommend following this order..and reinstalling in reverse order.Screw#1 is behind the fuse box panel. Screws #4/#5 are underneath the upper trim plate.
3a.
1
2
5
3
4
Youll have to unhook the VAG
Interface and two wires from a lowerdome light before the lower dash canbe removed.very easy.
Copyright Ted Basile ( [email protected] )
Nav Plus Phase 3(Removal of lower dashboard drivers side)
Updated: 11/9/2004
-
8/12/2019 Audi RNSD
35/84
Nav Plus Phase 3
3c
-
8/12/2019 Audi RNSD
36/84
Nav Plus Phase 3(Removal of lower dashboard passenger side)
Copyright Ted Basile ( [email protected] )
With the glove box sitting in this position,you only need to disconnect this wiringharness.
You can route all wires from thedrivers to the passenger sidethrough this area (above vents).
3c.
Updated: 11/9/2004
Nav Plus Phase 33d
-
8/12/2019 Audi RNSD
37/84
Nav Plus Phase 3(Plugging in Auxiliary Audio/Video Interface)
Unique 10 Pin audio/video
input (example: Nexxtel orDietz interface will convertthis to RCA-style A/Vinputs Yellow/Red/White)
Copyright Ted Basile ( [email protected] ) Updated: 11/19/2004
3d.
Please note: There is very limited space behind the head unit in an A6. I highly recommend running the cable for theA/V interface device from behind the drivers side opening. Once it is connected to the rear of the Nav+, you can gentlyslide the Nav+ back in place. Make sure the cable does not get crimped as you push the head unit back in place. Then
you can mount the A/V device.
Nav Plus Phase 33e
-
8/12/2019 Audi RNSD
38/84
Nav Plus Phase 3(Installing a Speed Sensor Switch)
Copyright Ted Basile ( [email protected] )
3e.
Connector III 8 Pin (Pin#1)- Symphony I
Connector V 26 Pin (Pin#5)
Please note: By installing this switch, you will allow your passengers to view video images on your Nav+ screenwhile you drive. Your GALA functionality will be eliminated as a result of this modification. Thus, the volume willnot increase/decrease as your speed increases/decreases. It is not safe to watch movies while you drive; please
perform this modification at your own risk.
Connector III 8 Pin (Pin#1)- Symphony II
or
Speed Sensor/GALA signal coming fromwiring harness or instrument cluster; split tosupport 26 pin connector
Do not interrupt thespeed signal going to
the 26 pin connector
Location of SpeedSensor Switch
Location of SpeedSensor Switch
Bose pin/wire is removed and taped off,not needed for Nav+ install
Updated: 11/9/2004
Nav Plus Phase 3
3f.
-
8/12/2019 Audi RNSD
39/84
Nav Plus Phase 3(Picture behind glove box area)
Copyright Ted Basile ( [email protected] )
Please note: The space behind the glove box is extremely tight. There is very little room to locate electronics. TheBlaupunkt ME3 is a large DIN sized unit that barely fit because of its required mounting depth. When you areselecting a DVD/MP3 player for this phase, youll want to research the installation dimensions needed. You might
even want to consider locating your DVD/MP3 player to some place in the trunk.
Passenger side airbag
3f.
The Blaupunkt ME3 dimensions:H: 60mm or 2 D: 198mm or 8W: 175mm or 7
7 of width is just enough, but 8 ofdepth was a bit too much. It fit, butit was a tricky installation.
Updated: 11/9/2004
Nav Plus Phase 3
3g.
-
8/12/2019 Audi RNSD
40/84
Nav Plus Phase 3(Removing the glove box door)
Copyright Ted Basile ( [email protected] )
To remove the glove box door, you need toremove two of these plastic pins and onesmaller plastic pin (not pictured)
DO NOT remove the Torx boltlocated inside here. It will make
it extremely difficult to realignthe glove box door.
3g.
Updated: 11/9/2004
Nav Plus Phase 3
3h.
-
8/12/2019 Audi RNSD
41/84
Nav Plus Phase 3(Location of ignition, battery and ground source)
Copyright Ted Basile ( [email protected] )
Ignition Power = 75XConstant Battery Power = 30
Please note: Before you unscrew these terminal connectors, make sure your metal socket wrench does not touchany metal parts of the lower dash area (you could damage other electronic components). I would highly recommenddisconnecting the battery just prior to connecting to these power sources
Common area for ground follow the brown wires
Updated: 11/9/2004
Nav Plus Phase 33i.
-
8/12/2019 Audi RNSD
42/84
Copyright Ted Basile ( [email protected] )
(Location of fuses for Nexxtel Interface and Blaupunkt ME3)
I ran two 3AMP fuses just above my fusebox to support the Nexxtel device and the
Blaupunkt ME3 unit. This way, I wont haveto pull open the dashboard to replace afuse.
This is the fused wiringharness for my Motorola v60Hands-free car kit. In this
space, it is very accessible toreplace fuses.
Updated: 11/9/2004
Nav Plus Phase 3
3j.
-
8/12/2019 Audi RNSD
43/84
(Installation of Blaupunkt ME3 in glovebox)
Copyright Ted Basile ( [email protected] )
One of the support brackets forthe ME3 was attached to theroof of the glove box.
Be careful that any wires dontdangle or come close to this light.It gets very hot and can melt a wirecasing.
I relocated the glovebox light here by
cutting out a new holeusing my Dremel tool.
Updated: 11/9/2004
Nav Plus Phase 3
3k.
-
8/12/2019 Audi RNSD
44/84
(Installation of Nexxtel Interface)
Copyright Ted Basile ( [email protected] )
Red wire = Ignition/Switched power (3AMP fuse)White wire = Battery/Continuous power (3AMP fuse)Black wire = Ground
10 pin adaptorconnects directlyto Video inputbehind Nav Plus.
The Nexxtel adaptor was attached to the drivers side lowerdashboard area using zip ties and Velcro tape.
Updated: 11/9/2004
Nav Plus Phase 33l.
-
8/12/2019 Audi RNSD
45/84
Copyright Ted Basile ( [email protected] )
In order to fit the ME3 into my glove box, Ineed to cut this section. By doing this, myglove box light does not work. Oh well.
(Installation of Nexxtel Interface and Blaupunkt ME3 CD/DVD/MP3/TV Tuner)
If you wanted to use the ME3 inyour house, you would need topurchase an additional AC/DCadaptor
Wiring harness for ME3 plugsin here (power, A/V etc.).
Antenna for TV tuner plugs inhere (F-style coax connector).
A I bracket from a
hardware store was used tobrace this side of the ME3to the glove box.
Updated: 11/9/2004
Nav Plus Phase 3
3m.
-
8/12/2019 Audi RNSD
46/84
(Final Wiring of Nexxtel Interface and Blaupunkt ME3)
Copyright Ted Basile ( [email protected] )
All of the power and ground wires for the Nexxtel and Blaupunkt ME3 wrapped in blackOEM-like fabric tape and zip ties. You should adjust your steering wheel up and down tosee if your wiring interferes with its operation.
TMC/CAN gateway
Updated: 11/9/2004
Nav Plus Phase 3(I ll i f N l I f d Bl k ME3 CD/DVD/MP3/TV T )
3n.
-
8/12/2019 Audi RNSD
47/84
Copyright Ted Basile ( [email protected] )
(Installation of Nexxtel Interface and Blaupunkt ME3 CD/DVD/MP3/TV Tuner)
With the ME3 reinstalled, I left my speed sensor switch and a set ofauxiliary inputs accessible.
The ME3 stays relatively warm.The heat vents are exposedinside and behind the glove box.
Updated: 11/9/2004
Nav Plus Phase 3(L ti f IR f Bl kt ME3 CD/DVD/MP3/TV T )
3o.
-
8/12/2019 Audi RNSD
48/84
Copyright Ted Basile ( [email protected] )
(Location of IR sensor for Blaupunkt ME3 CD/DVD/MP3/TV Tuner)
Running the wire for the IR sensor was extremely easy. There is an open space where the dashboard meets thebottom of the windshield. I used a 2 plastic putty knife to feed the wire along the edge of the windshield and at thebase of the A pillar.
Updated: 11/9/2004
Nav Plus Phase 3(Aftermarket Amplified TV Tuner antenna)
3p.
-
8/12/2019 Audi RNSD
49/84
Copyright Ted Basile ( [email protected] )
(Aftermarket Amplified TV Tuner antenna)
Please note: The Blaupunkt ME3 comes with a non-amplified TV antenna. The reception is horribleso I decided toinvest in an amplified antenna. I will hide it in the headliner near the windshield and run the wire down the A pillar.This antenna has a F-connector which works with my ME3.
http://www.qualitymobilevideo.com/tvtunersandantennas.html
Updated: 11/9/2004
Nav Plus Phase 3(Blaupunkt ME3 Screen Shot DVD Player Mode)
3q.
-
8/12/2019 Audi RNSD
50/84
Copyright Ted Basile ( [email protected] )
(Blaupunkt ME3 Screen Shot DVD Player Mode)
Updated: 11/9/2004
With an A/V input into your Nav+, you can still toggle between thenavigation map screen and Video input screen, while listening to the audiofrom your DVD source. Very cool!!
Nav Plus Phase 3(Blaupunkt ME3 Screen Shot TV Tuner Mode)
3r.
-
8/12/2019 Audi RNSD
51/84
Copyright Ted Basile ( [email protected] )
(Blaupunkt ME3 Screen Shot TV Tuner Mode)
Updated: 11/9/2004
With an A/V input into your Nav+, you can still toggle between thenavigation map screen and Video input screen, while listening to the audiofrom your DVD source. Very cool!!
Nav Plus Phase 3(Blaupunkt ME3 Screen Shot Toggle between Map Screen)
3s.
-
8/12/2019 Audi RNSD
52/84
Copyright Ted Basile ( [email protected] )
(Blaupunkt ME3 Screen Shot Toggle between Map Screen)
Updated: 11/9/2004
With an A/V input into your Nav+, you can still toggle between thenavigation map screen and Video input screen, while listening to the audiofrom your DVD source. Very cool!!
Nav Plus Phase 3(Blaupunkt ME3 Screen Shot MP3 Mode Folder/File Names)
3t.
-
8/12/2019 Audi RNSD
53/84
Copyright Ted Basile ( [email protected] )
(Blaupunkt ME3 Screen Shot MP3 Mode Folder/File Names)
Updated: 11/9/2004
With an A/V input into your Nav+, you can still toggle between thenavigation map screen and Video input screen, while listening to the audiofrom your DVD source. Very cool!!
-
8/12/2019 Audi RNSD
54/84
2001 A6 Avant Interior Modifications3v.
-
8/12/2019 Audi RNSD
55/84
Updated: 11/9/2004
OEM Auto-dimming Compass Mirror
H-Free MIC (integratedwith wiring cover)
IR Receiver for ME3
Blaupunkt ME3(DVD/CD/MP3/TV Tuner)
Nexxtel Video Interface & TMC/CANGateway (inside lower dash)
OEM Nav Plus
Aux. cigarette lighter
adaptor (not pictured)
TT 3 spoke steering
wheel
Motorola v60 H-Free kit
VW Touareg cigarettelighter flashlight
Copyright Ted Basile ( [email protected] )
4.
-
8/12/2019 Audi RNSD
56/84
Audi Navigation Plus Other Input Devices
Pictures: 4a 4g
Nav Plus Installation(Running OEM CD changer cable and PhatBox in trunk)
4a.
-
8/12/2019 Audi RNSD
57/84
( g O g b t t )
Courtesy of Ted Basile ( [email protected] )
For more information please contact:Jeffrey D. Bipes
[email protected]://forums.audiworld.com/audio/msgs/38643.phtml
InputOutput
CD Changer PhatBox or BlitzSafe etc.
If you have a 2003/2004 A6, then youllneed the CD Changer cable for the trunk.Audi Part# 4B0-051-735-B
Updated: 11/9/2004
Nav Plus Installation(Non-OEM Audio/Video Input Interfaces)
4b.
-
8/12/2019 Audi RNSD
58/84
( p )
Courtesy of Ted Basile ( [email protected] )
Available at www.nav-plus.comAlso available at www.vwnavi.com
Sky Tougas
President & Co-Founderwww.Nav-Plus.comTel: 401.741.9061Fax: 401.782.4455Email: [email protected]
Also available at www.nexxtel.de
Available at www.navtv.comAlso available at www.vwnavi.com
NAV-TV Corp.
100 NW 11th StreetBoca Raton, FL 33432866-477-3336 toll free561-955-9770 International
516-955-9760 Fax
Updated: 11/9/2004
Nav Plus Installation(Non-OEM Audio/Video Input Interfaces)
4c.
-
8/12/2019 Audi RNSD
59/84
( p )
Courtesy of Ted Basile ( [email protected] )
Available at www.nav-plus.com
Sky TougasPresident & Co-Founder
www.Nav-Plus.comTel: 401.741.9061Fax: 401.782.4455Email: [email protected]
Available at www.navtv.com
NAV-TV Corp.100 NW 11th Street
Boca Raton, FL 33432866-477-3336 toll free561-955-9770 International
516-955-9760 Fax
Updated: 11/9/2004
Nav Plus Installation OEM Glovebox CD Changer4d.
-
8/12/2019 Audi RNSD
60/84
Courtesy of Ted Basile ( [email protected] )
For the B6 A4/S4 and C6 A6, Audi offers a glove box CDChanger. Unfortunately, there is a specific version/revision letterthat works with the Navigation Plus. The US Audi parts dealerscannot source this part. You can contact www.vagparts.com asthey can order it for you.
For the OEM glove box changer you must get part#8E0 035 111 B, or C. It must have a version letter at the end ofthe part number. It also requires harness, part#8E0 051 592.
Please note: If you would like to mount this OEM CD Changer in your glove box, please follow some of the stepsthat I took to install the Blaupunkt ME3. You can always consult a car stereo installation shop as another option.
Updated: 11/9/2004
Nav Plus Installation PhatNoise PhatBox MP3 Player4e.
-
8/12/2019 Audi RNSD
61/84
If you have a 2003/2004 A6, thenyoull need the CD Changer cable toconnect your PhatBox to the Nav
Plus.
Audi Wiring harness:Audi Part#: 4B0 051 735Bwww.clairparts.com
Courtesy of Ted Basile ( [email protected] )
Blue/Green/Yellow 20 pinconnector
Updated: 11/9/2004
Nav Plus Installation(Non-OEM Audio Input Interfaces)
4f.
-
8/12/2019 Audi RNSD
62/84
BlitzSafe Adaptor (part# AUDI/AUX DMX V.1B) will work with the Audi Navigation Plus. You can alsopurchase a version with a specific audio interface to Pioneer, Alpine, Kenwood etc aftermarket XM radios etc.
Please note: If you use a BlitzSafe adaptor, you wont be able to hook up the OEM CD changeror PhatNoise PhatBox and use the Nav+ to control track up/down etc.
Three piece 20 pinConnector.
This wire MUST begrounded
Male version of the20 pin connector.
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
4g.
Nav Plus Installation Dietz 1213 device(Non-OEM Audio Input Interfaces)
-
8/12/2019 Audi RNSD
63/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Please note: This is only for audio input via the OEM TV input interface. This is ideal if you wantto run the audio from your iPOD or another MP3 player into your Nav unit. You will probablyhave a pink screen on the Nav+ video display if you use one of these devices.Available at www.vwnavi.comor www.nav-plus.com
Plugs into the unique 10Pin audio/video inputbehind your Nav+.
5.
-
8/12/2019 Audi RNSD
64/84
Audi Navigation Plus Screen Shots
Pictures: 5a 5j
-
8/12/2019 Audi RNSD
65/84
5b Nav Plus in Action Screen Shots(Compass Display)
-
8/12/2019 Audi RNSD
66/84
Copyright Ted Basile ( [email protected] ) Updated: 11/19/2004
Nav Plus in Action Screen Shots(Various volume settings)
5c
-
8/12/2019 Audi RNSD
67/84
Copyright Ted Basile ( [email protected] )
Please note: The TP (traffic program) volume is only applicable in Europe.
Updated: 11/19/2004
Nav Plus in Action Screen Shots(TMC rerouting options - 1)
5d
-
8/12/2019 Audi RNSD
68/84
Copyright Ted Basile ( [email protected] )
Please note: The TMC/CAN gateway needs to be installed and operational to see thisscreen. You access this screen by pressing the button with the three cars, while navigating.
Updated: 11/19/2004
Nav Plus in Action Screen Shots(TMC rerouting options - 2)
5e
-
8/12/2019 Audi RNSD
69/84
Copyright Ted Basile ( [email protected] )
Please note: You can select the specific portion of your route to navigate around. Very cool!
Updated: 11/19/2004
Nav Plus in Action Screen Shots(TMC rerouting options - 3)
5f
-
8/12/2019 Audi RNSD
70/84
Copyright Ted Basile ( [email protected] )
Please note: With the right hand knob, you can specify the detour distance in increments of .06 miles.
Updated: 11/19/2004
Nav Plus in Action Screen Shots(TMC rerouting options - 4)
5g
-
8/12/2019 Audi RNSD
71/84
Copyright Ted Basile ( [email protected] ) Updated: 11/19/2004
Please note: In North America, this screen doesnt do anything. This is only applicable inEurope where the Traffic Message Channel service is available.
Nav Plus in Action Screen Shots(TMC rerouting options 5)
5h
-
8/12/2019 Audi RNSD
72/84
Copyright Ted Basile ( [email protected] )
Please note: In North America, this screen doesnt do anything. This is only applicable inEurope where the Traffic Message Channel service is available.
Updated: 11/19/2004
-
8/12/2019 Audi RNSD
73/84
Audi Navigation Plus Screen Shots (Special Destinations in Map/Navigation Mode)5j
-
8/12/2019 Audi RNSD
74/84
Copyright Ted Basile ( [email protected] ) Updated: 7/19/2004
-
8/12/2019 Audi RNSD
75/84
Audi Navigation Plus InteriorPictures of European Model C5
A6/S6/RS6/allroad
Pictures: 6a 6i
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6a
-
8/12/2019 Audi RNSD
76/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
-
8/12/2019 Audi RNSD
77/84
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6c
-
8/12/2019 Audi RNSD
78/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6d
-
8/12/2019 Audi RNSD
79/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6e
-
8/12/2019 Audi RNSD
80/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6f
-
8/12/2019 Audi RNSD
81/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6g
-
8/12/2019 Audi RNSD
82/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus RNS-E DVD in Action Screen Shots(Interior pictures from European model Audis)
6h
-
8/12/2019 Audi RNSD
83/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004
Nav Plus in Action Screen Shots(Interior pictures from European model Audis)
6i
-
8/12/2019 Audi RNSD
84/84
Courtesy of Ted Basile ( [email protected] ) Updated: 11/9/2004