WIFI ANTENNA

Connect to CARPLAY-USB cable

Multimedia USB RGB input cable

Update adapter

Connect to the Phone's original cable

Optional cable

Connect to RGB output device

C6/C7 switch wiring for A/C panel or gateway box.(A8 using spreaded out line)

Blue & white wire for MMI controlConnect to PIN10 of the headunit's ISO power socket

Connect to the original headunit's big ISO connector (The position of the green inserts)

RED---12V output for rear view camera

ORANGE--Reverse control cable (connect to reversing light) for AVM /without reversing gridline

YELLOW---RCA Front/Rear video input(Connect to front /rear view camera/360 AVM/DVR

Stereo audio cableBLACK---Stereo audio output

Power cable

Microphone

Connect to A/C panel or gateway box port

Connect to cable pulled fromA/C panel or gateway box port

Connect to the original headunit's cable (The original cable is gray).

Plug into the original headunit's LVDS port

Connect to the unplugged greeninserts from the original headunit'sISO cable

REMARK:Please keep in the AUX interface when switch the CarPlay interface(If there is no AUX status,pls activate it by computer)

1) For A6/A7 control panel,long press and hold "NAV" button to switch MENU,long press"NAV" button again,exit the switch MENU.

2)Short press "TEL" button to open "Siri".

3)Knob to control up/down/right/left/ok.

1) For A1/Q3 control panel,long press and hold Voice control button toswitch MENU,long press Voice control button again,exit the MENU.

2)Short press " Voice control" button to open "Siri".

3)Steering wheel Roller to control up/down/ok.

Reset Dip Switch LED

OFF

ON

PIN 4 OFF/ON

PIN 6 OFF/ON

PIN 7 OFF/ONPIN 8 OFF/ON

Reversing gridline/Enable 360 panoramic

Rear view camera CVBS input / RGB input

Aftermarket rear view CAM/Original rear view CAM

NG/Touch point coordinate correction,and turn to "OFF"

PIN 1 PIN 2 PIN 3 PIN 5 CAR MODEL

ON OFF OFF OFF

ON OFF ON OFF

OFF OFF ON OFF

ON ON OFF OFF

OFF ON OFF OFF

OFF OFF OFF OFF

OFF OFF OFF ON

ON OFF OFF ON

ON OFF ON ON

OFF OFF ON ON

OFF ON ON ON

Audi (A6/Q3/Old Q7) WIRING DIAGRAM

2010~2012 A6L/A7(C6) CAN1 connect to gateway box10-12 Q7 (7") CAN 1 connect to A/C beige socket's pin7&pin8

13-15 A6/A7/A8(C7) CAN1 connect to A/C red socket's pin4&5

09~18 A4/A5/Q5 CAN1 connect to gateway box's red socket's pin5&pin15 .(Gateway bos is in the left side of the co-pilot)High-end 7" A1/Q3 CAN1 connect to gateway box's (Under the steering wheel)pin5&15 or to A/C panel's beige socket's pin12&13Low-end 6.5" A1/Q3 CAN1 connect to gateway box's (Under the steering wheel)pin5&15 or to A/C panel's beige socket's pin12&13USA version A4/A5/Q5 CAN1 connect to gateway box's red socket's pin5&pin15 .(Gateway bos is in the left side of the co-pilot)

USA version Q7 (6.5") CAN1 connect to A/C beige socket's pin7&8

17~18 A4/Q7(7") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7; 09~11 Q7 MMI bule&white wire connect to pin3

16~18 A6/A7/A8l CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7; MMI system bule&white wire connect to pin3

Lamando/high-end A3(7") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7

Lamando/Low-end Q3/A3(5.8") CAN1 connect to ISO socket's (Gray socket)pin6&12,CAN2 connect to pin1&7

LCD OUT cable

LCD IN cable

Microphone cable

DIP SWITCH SETTING(After changing the dip code,press "reset"or power-on again)

ampireLDS INTERFACE

ampireLDS INTERFACE

ampire