atlas copco exploration products boyles c6/c6c core...

4
Atlas Copco Exploration Products Boyles C6/C6C core drilling rig Technical specification Flexible enough to take on almost any job The Boyles C6 surface core drilling rig is part of the Boyles range, a new generation of Atlas Copco quality drilling rigs that combine productivity with a favorable life cycle cost. Boyles C6 represents the most flexible rig size in the Boyles range and is available in trailer-mounted (Boyles C6) or crawler-mounted (Boyles C6C) versions. Safe and ergonomic Two E stops on the drill unit are standard and Boyles C6C has another E stop for the Radio Remote Control. Drill operators are protected from the rotation unit by a safety cage. Possible to operate by feel while focusing on the drilling operation, thanks to the operator friendly control panel. Flexible drilling rig size Compact structure, giving excellent space utilization using fitted modules. Foldable 2-section mast simplifies short-distance transport of the rig. Reliable and powerful Both the Boyles C6 and Boyles C6C are equipped with: A powerful main hoist. A rod holder with a long-life gas cartridge that handles rods from BO to PO size and casing up to HW. A proven and reliable rotation unit with 4-speed gear box that can generate the high rates of penetration with very high torque when it is required. A reliable power unit, Cummins QSB 6.7 Tier III (153 kW), which brings out the full capacity of the rig, resulting in higher penetration rates to the bottom of the hole. Radio remote controlled (Boyles C6C) The tramming functions of the rig can be precisely controlled from a safe distance, eliminating the danger of being on or next to the machine while in motion. If radio contact is lost, tramming will stop automatically.

Upload: lyduong

Post on 14-Mar-2018

340 views

Category:

Documents


6 download

TRANSCRIPT

Page 1: Atlas Copco Exploration Products Boyles C6/C6C core ...sumitec.ru/upload/catalog/atlas-copco/kolon-bur/BoylesC6C6C.pdf · Atlas Copco Exploration Products Boyles C6/C6C core drilling

Atlas Copco Exploration Products

Boyles C6/C6C core drilling rig

Technical specification

Flexible enough to take on almost any jobThe Boyles C6 surface core drilling rig is part of the Boyles range, a new generation of Atlas Copco quality drilling rigs that combine produc tivity with a favorable life cycle cost. Boyles C6 repre sents the most flexible rig size in the Boyles range and is available in trailer-mounted (Boyles C6) or crawler-mounted (Boyles C6C) versions.

Safe and ergonomic• Two E stops on the drill unit are standard and Boyles C6C

has another E stop for the Radio Remote Control.

• Drill operators are protected from the rotation unit by a safety cage.

• Possible to operate by feel while focusing on the drilling operation, thanks to the operator friendly control panel.

Flexible drilling rig size • Compact structure, giving excellent space utilization

using fitted modules.

• Foldable 2-section mast simplifies short-distance transport of the rig.

Reliable and powerfulBoth the Boyles C6 and Boyles C6C are equipped with:

• A powerful main hoist.

• A rod holder with a long-life gas cartridge that handles rods from BO to PO size and casing up to HW.

• A proven and reliable rotation unit with 4-speed gear box that can generate the high rates of penetration with very high torque when it is required.

• A reliable power unit, Cummins QSB 6.7 Tier III (153 kW), which brings out the full capacity of the rig, resulting in higher penetration rates to the bottom of the hole.

Radio remote controlled (Boyles C6C)The tramming functions of the rig can be precisely controlled from a safe distance, eliminating the danger of being on or next to the machine while in motion. If radio contact is lost, tramming will stop automatically.

Page 2: Atlas Copco Exploration Products Boyles C6/C6C core ...sumitec.ru/upload/catalog/atlas-copco/kolon-bur/BoylesC6C6C.pdf · Atlas Copco Exploration Products Boyles C6/C6C core drilling

2

Specifications

Main hoist

The powerful main hoist, equipped with a hydraulic motor and a dual brake system, ensures a well-con-trolled speed. The dual brake system offers both dyna mic and static break-ing. When the lifting operation is stopped, firm self-locking is applied.

Single line capacity Bare drum: 80 kN (18 000 lb)

Line speed Bare drum: 44 m/min (148 ft/min)

Cable size 27 m (89 ft) x 16 mm (10/16 in)

Wireline hoist

The wireline hoist has a high level of speed control to ensure safe and consistent opera tion.

Capacity1,830 m (6 000 ft) of 4.76 mm (3/16 in)

975 m (3 200 ft) of 6.35 mm (1/4 in)

Line pullBare drum: 11.9 kN (2,665 lb)

Full drum: 3.0 kN (668 lb)

Line speedBare drum: 114 m/min (374 ft/min)

Full drum: 453 m/min (1 486 ft/min)

Mast and feed system

Feed travel 3.5 m (11.5 ft)

Feed speeds Fast and slow with variable control

Thrust 59.6 kN (13 390 lb)

Pull 138 kN (31 020 lb)

Drilling angle 45 to 90 degrees

Rod pull length 6.09 m (20 ft)

Power unit

Manufacturer Cummins

Model QSB6,7 Tier III

Volume 6.7 liter 6 cyl.

Power 153 kW (208 hp)

RPM 1 800

Engine type Diesel turbocharged/after cooled

Cooling Water

Electrical system 24 V (alternator 24 V, 95 Amp)

Hydraulic system

Primary pump 28 MPa – 242 l/min (4,061 psi – 63.9 gal/min)

Secondary pump 20 MPa – 122 l/min (2,901 psi – 32.2 gal/min)

Auxiliary pump 21.5 MPa – 47 l/min (3,118 psi – 12.4 gal/min)

Hydraulic oil cooling Air

Rotation unit

The rotation unit can handle BO-PO rods and BW-HW casing. It consists of a hydraulic motor, a sealed gear-box, a hollow spindle and an Atlas Copco patented hydraulic chuck, and quick change chuck jaws. The rotation speed is adjustable from the control panel.

Power Hydraulic motor – variable speed/reversible

Final drive 4 in chain driven in oil bath – 2,5 ratio

Spindle (inner diameter) 117 mm (4 5/8 in)

Spindle data

Ratio Speed, rpm Torque, Nm Torque, ftlb

1st 6.63:1 117–196 5 113–3 051 3 771–2 250

2nd 3.17:1 245–410 2 445–1 459 1 803–1 076

3rd 1.72:1 451–756 1 326–792 978–584

4th 1.00:1 776–1 300 771–460 569–340

Range selection Manual control from operator’s station

Hinged head Swing away

Chuck assemblyType Hydraulically opened, spring closed

Maximum inside diameter 117 mm (4 5/8 in)

Holding capacity 18 143 kg (40 000 lb)

Rod Holder

The rod holder is hydraulically opened and closed by gas pressure. In case of loss of hydraulic pressure, the rod holder closes instantly. The gas pressure can be conveniently monitored.

Type Hydraulically opened, gas spring closed

Maximum inside diameter 210 mm (8,3 in)

Holding capacity 13 000 kg (28 660 lb)

Page 3: Atlas Copco Exploration Products Boyles C6/C6C core ...sumitec.ru/upload/catalog/atlas-copco/kolon-bur/BoylesC6C6C.pdf · Atlas Copco Exploration Products Boyles C6/C6C core drilling

3

Standard equipment

Hydraulic mast dump

Mast in two sections

Large crown sheave wheel

Wear lines on lower mast

Safety guards

Hydraulic oil reservoir fill pump and filtration

Tier III diesel engine

Control panel

Hydraulic P-size rod holder

4 hydraulic leveling jacks

Fuel tank 200 l (53 gal)

Fuel filter and water separator

Hydraulic mast raise

Feed wear protection plates

Lighting kit

E-stop devices

Spindle tachometer

Drill base supports

Boyles C6 and Boyles C6C

Support 4 hydraulic jacks

Pad diameter 200/230 mm (7.87/9 in)

Travel length 550 mm (21.6 in)

Boyles C6 Trailer mounted rig, four 770 mm (30.3 in) wheels, towing package

Boyles C6C

Crawler mounted rig, radio remote controlled

Max speed 3.3 km/h

Heavy duty crawler tracks 300 mm wide

Optional equipment

Hydraulic mud mixer

Water flow meter Max 6.4 MPa

Hydraulic mud pump, Trido 140 140 l/min (37 gal/min) / 7 MPa (1 015 psi)

High altitude kit

Page 4: Atlas Copco Exploration Products Boyles C6/C6C core ...sumitec.ru/upload/catalog/atlas-copco/kolon-bur/BoylesC6C6C.pdf · Atlas Copco Exploration Products Boyles C6/C6C core drilling

Atlas Copco Geotechnical Drilling and Exploration www.atlascopco.com

© C

opyr

ight

201

2, A

tlas

Cop

co C

rael

iuss

AB

, Mär

sta,

Sw

eden

. All

prod

uct n

ames

in th

is p

ublic

atio

n ar

e tra

dem

arks

of A

tlas

Cop

co. A

ny u

naut

horis

ed u

se o

r cop

ying

of t

he

cont

ents

or a

ny p

art t

here

of is

pro

hibi

ted.

Thi

s ap

plie

s in

par

ticul

ar to

trad

emar

ks, m

odel

deno

min

atio

ns, p

art n

umbe

rs a

nd d

raw

ings

. lllu

stra

tions

and

pho

tos

in th

is b

roch

ure

may

sho

w e

quip

men

t with

opt

iona

l ext

ras.

Spe

cific

atio

ns a

nd e

quip

men

t sub

ject

to c

hang

e w

ithou

t not

ice.

Con

sult

your

Atla

s C

opco

Cus

tom

er C

ente

r for

spe

cific

info

rmat

ion.

6991

175

6 01

Mär

sta,

Sw

eden

, Nov

embe

r 201

2

Measurements and weights

Weight

Boyles C6 incl. Trido140 7 000 kg (15 430 lb)

Boyles C6C incl. Trido140 9 000 kg (19 838 lb)

A B C

D

E

F

G

H

I

45 °

90 °

A

DC

B

E

A

B C

D

E

G

H

45 °

90 °

A

C D

B

EBoyles C6

Boyles C6

Boyles C6

Boyles C6C

Boyles C6C

Boyles C6C

Working dimensionsBoyles C6 Boyles C6C

Dimension mm in mm in

A 10 082 397 10 082 397

B 7 294 287 7 541 297

C 9.5 0.4 256.5 10.1

D 196.5 7.7 87 3.4

E 7 486 295 7 486 295

Capacity drilling depthBoyles C6 and Boyles C6C

m ft

B Wireline 1 540 5 052

N Wireline 1 200 4 042

H Wireline 800 2 695

P Wireline 475 1 558

Depth are based on vertical hole

Transport dimensionsBoyles C6 Boyles C6C

Dimension mm in mm in

A 222 8.7 321 12.6

B 2 205 87 2 634 104

C 2 602 102 2 817 111

D 6 525 257 5 302 209

E 2 625 104 2 555 101

F 379.5 14.9 – –

G 3 400 134 4 905 193

H 705 28 705 28

I 1 927 76 – –