HOW TO ASSEMBLII ' l ' l lu ' l 'RAMPOt,tNI. l ' rENT

I tcld al l assembly stcps careful ly belorc bcgrrrrrrrr l l lo rrsscrtrblc thc terrt . l {elL'r to drawings for clari f icat ion, i t is

te(()mmended that trvtr pcoplc asscnrhlc t lrrs tcnl tolt ' l l rcr.

No tools are requirc(l l i rr t l re tctr l rrrrenthly nor alt) 'scrc\\s or t tuts. l t is rccorrurrurt lct l thl t gloves are wom whilst you

assctnble the tent. lh. ' tr ,rrrr lxr lrnc can be regardctl ls a "tahlc" to keep thc tcrrt ol l t l rc ground and offer a frame of

re I crcncc.

s l l l , I

, , \rrctrrhlc thc t l trcc l ibcrglass poles by joining the sections together with exist ing conncct()r\ i l t tached to the poles. The

rrrsrt lc cl lst ic cord can be seen in the poles which holds them rigidly together. (Sec l igurc I )

POIE CONNECTOR POIEt lI I

t ,

{-INSERT

ffiffiffiSTEP 3:

Please check thc' tubc size of the vertical leg first.

If the trampolinc lcg(s) tuhc with 48, please see the figure 3.

FIGURE 3

Now begin to assemble the PAT'INT bracket parts ol'tent unit (Locate two opposite trampoline legs on the frame.)

Place the bracket onto the trarnpoline liantc, there is a bulge filr the bracket that connects it to the frame, screws and nuts

are not required to fasten it. Makc surc that you install it tiorn inside of the trampoline rail and against the trampoline

leg(s) then place the connect()r sysl.enr with Iibcrglass sockets into the notch of the bracket. Fasten tight the screw at the

bracket. l t is the sanrc syslcrn l i rr l tranrpol i l lc tol l l .

I f the trampolne leg(s) lubc rvith,12. plcasc scc thc l ' igurc 4.

Now begin to assemble the PA fEN'l' hrue kct plrts of tent unit (Locate two opposite trampoline legs on the fi'ame.)

Place the bracket onto the trampolinc lllnrc. thcrc is a bulge for the bracket that comects it to the frame, screws and nuts arenot required to fasten it. Make sure thirt y()u install it liom inside of the trampoline rail and agalnst the trampoline leg(s) and useO42 RINGENT TUBE to adjust thc tLtbc sizc, Chcck the bracket can lock the frame tight, and then place the connector systemwith fiberglass sockets into the notch ol tlrc hracket. Fasten tight the screw at the bracket. It is the same system for a

trampoline tent

If the trampoline leg(s) tube with 38, pleasc scc the figur:e 5

It

ERACKET9 0 ' c l o c ruffiMrJ\_,r\Jt( [o v uL\-/\-K, FIGURE I

BT] ( 'AREI-UL OF THE POLE ENDS AND CONNECTOR WHEN YOU ASSEMBLI.] ' I ' I IU POLES AS THERE

IS PO'I'ENTIAL HAZARD TO CLAMPYOU HANDS.

Alicr assembling they should be placed on the ground and you should have 3 assembled polcs bc ol'the same length.

S ' l ' l : l ' 2 :

Now plitcc the tent on the Trampoline and determine which direction you want the door to lhcc. The screened door is' l )" slrapcd with zippers on the inside and outside" this wil l be your tent access point. l ) lclsc rnuke sure that there are 3

slccrcs u'hich divide the whole tent into 4 parts of the same area and the sleeves arc u1'r ugrrinst thc top frame (that is the

ctr lvcd plrts ol ' tcnt is up against the mat) (see f igure 2)

Norr sl i t lc ottc t tssctnblcd pole into the sideward sleeve of the tent, do not force thc yrlc(s) through the sleeve(s), you

llir\c lo Fitlltur tctlt lirbric together to ease the pole through the sleeve. Repeat with thc othcr two poles into the other

Iwo s lcc r cs

BRACKET3 0 ' C L O C K

II

ffiffiMFIGURE 5

l 2 0 ' c l o c K

DOOR (6 O 'CLOCK)

l ; l ( i t l l i l : l