assembly and installation instructions · 2. loosen the set screws and remove the bottom frame from...
TRANSCRIPT
ASSEMBLY AND INSTALLATION INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUITBREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
P0012
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
120508Page 1
Twist the lockingtube to open or close loop lock
Loop lock
Figure.1
Outlet BoxHousing Grounding Wire
Wire Nut
Fixture WireFixture Grounding Wire
Mounting Plate
Green Grounding Screw
Fixture Mounting Screw
Lock Nut
Upper Canopy
Lower Canopy
Glass Shade
Socket Ring
Glass Holder
Main Fixture
Loop Lock
Tube
Set Screw
Threaded Pipe
Ball Nut
Mounting Screw
Bulb Type B Max.60W (not included)
Washer
Hex Nut
Chain
Loop
Spacer
Bottom Frame
Loop
Socket Base
3-Way Switch
Socket Ring Fixer
Page 2
1. Thread two fixture mounting screws to the mounting plate, and secure them with two lock nuts. Adjust the length of the fixture mounting screws if necessary. 2. Attach the mounting plate to outlet box by using two mounting screws. 3. Before installing the fixture, unscrew two set screws and open the bottom fixture, then remove the foam / bubble bag from the fixture. 4. Close the bottom frame and screw it with two set screws 5. Screw the threaded pipe into the coupling of the main fixture, Then slide the tube down through the threaded pipe. (See Fig. 2) 6. Repeat with the other threaded pipes and tubes. 7. Place the lower canopy over the tubes, making sure the threaded pipes feed through the holes of lower canopy, then screw lower canopy with washers and hex nuts. 8. Choose the length of the chains you need. 9. Take one loop lock, open the locking tube, then hook it onto the loop of the upper canopy and onto one end of the chain. Close back the locking tube of the loop lock. (See Figure.1) 10. Take another loop lock, open the locking tube, then hook it onto the loop of the lower canopy and onto the other end of one chain. Close back the locking tube of the loop lock. (See Figure.1) 11. Repeat steps 8~9 to connect the another chain to the upper canopy and lower canopy. 12. Thread the fixture wires and fixture grounding wire through one of the chains and out from the upper canopy. 13. Cut any excess fixture wires and fixture grounding wire. Slit the two fixture wires apart in 5 inches. Peel off insulation of the two wires in 5/8 inch. 14. Pull out the house supply wires and the house grounding wire from the outlet box. Make wire connections using the wire nuts: --- The smooth wire (marked) from the fixture to the black wire from the power source. --- The ridged wire (unmarked) from the fixture to the white wire from the power source. --- Attach the fixture grounding wire to the mounting plate with the green grounding screw. Then connect it to the house grounding wire with a wire nut. Carefully put the wires back into the outlet box. 15. Raise the upper canopy against the ceiling, with the fixture mounting screws located on the mounting plate protruding from the holes in the upper canopy, secure it with two ball nuts. 16. Attach the glass shades onto the glass holders, then secure them with the spaces and socket rings, using supplied socket ring fixer. 17. Install bulbs (not included). See relamping label at socket area or packaging for maximum allowed wattage. 18. Turn on the power at the main fuse or circuit breaker box.
120508
Figure.2
Contents of Spare Parts:
Assembly Kit(1 SET)(4526MM)
Glass Shade (6 PCS) (9341UE)
Socket Ring (6 PCS) (4523KK)
Main Fixture
Tube
Threaded Pipe
Coupling
Spacer (6 PCS) (4523PP)
Bottom Flat Glass (1 PC) (9340UE)
Page 3 120508
Figure.4
Main Fixture
1. Before install or replace the light bubes, shut off power at the main fuse or circuit breaker box.2. Loosen the set screws and remove the bottom frame from the main fixture.3. Remove the lens and old fluorescent tubes.4. Install new fluorescent tubes. See relamping label at socket area or packaging for maximum allowed wattage. 5. Restore the lens. Then restore the bottom frame.6. Turn on the power at the main fuse or circuit breaker box.
Bottom Frame
Set Screw
Lens
T4 FluorescentTube Max. 16 W(included)
INSTALL OR REPLACE LIGHT BULB:
SwitchFig. 3
Socket BaseFunction and Operation: 1). If the light will not turn on, make sure the switch of socket base is on. (See Fig. 3)2). Choose a mode by turn the 3 - way switch on the side of fixture. (See Fig. 4) Turn the 3 - way switch clockwise, the bottom light will brighten and the side lights will turn off. Turn the 3 - way switch clockwise again, the bottom light will turn off and the side lights will brighten. Turn the 3 - way switch clockwise again, all lights will brighten. Turn the 3 - way switch clockwise again, all lights will turn off.
3 - Way Switch