as-nzs 60417-2!5!2004 graphical symbols for use on equipment part 2-1 gerneral application

7/25/2019 As-NZS 60417-2!5!2004 Graphical Symbols for Use on Equipment Part 2-1 Gerneral Application

1/79

AS 60417.2.12004IEC 60417-2:1998,

IEC 60417-2:1998 Amdt 1:2000 and

IEC 60417-2:1998 Amdt 2:2002

Australian Standard

Graphical symbols for use onequipment

Part 2.1: General application

AS6041

7.2.12004

Accessedb

yEDITHCOWANUNIVERSITYLIBRARY

on03Feb2016[WITHDRAWN](Docum

entcurrencynotguaranteedwhenprinted

)


2/79

This Australian Standard was prepared by Committee TE-013, Symbols, Units andQuantities for Electrotechnology. It was approved on behalf of the Council ofStandards Australia on18 March 2004.This Standard was published on 30 July 2004.

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology andsystems. To maintain their currency, all Standards are periodically reviewed, andnew editions are published. Between editions, amendments may be issued.Standards may also be withdrawn. It is important that readers assure themselvesthey are using a current Standard, which should include any amendments whichmay have been published since the Standard was purchased.

Detailed information about Standards can be found by visiting the Standards WebShop at www.standards.com.au and looking up the relevant Standard in the on-linecatalogue.

Alternatively, the printed Catalogue provides information current at 1 January eachyear, and the monthly magazine, The Global Standard, has a full listing of revisionsand amendments published each month.

Australian StandardsTM and other products and services developed by StandardsAustralia are published and distributed under contract by SAI Global, whichoperates the Standards Web Shop.

We also welcome suggestions for improvement in our Standards, and especiallyencourage readers to notify us immediately of any apparent inaccuracies orambiguities. Contact us via email at [email protected], or write to the ChiefExecutive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW2001.

This Standard was issued in draft form for comment as DR 03054.

Accessedb




)


3/79

AS 60417.2.12004

Australian Standard

Graphical symbols for use onequipment

Part 2.1: General application

Originated as part of AS 1104S1978.Revised and redesignated in part as AS 60417.2.12004.

COPYRIGHT

Standards Australia InternationalAll rights are reserved. No part of this work may be reproduced or copied in any form or by anymeans, electronic or mechanical, including photocopying, without the written permission of thepublisher.

Published by Standards Australia International LtdGPO Box 5420, Sydney, NSW 2001, Australia

ISBN 0 7337 6082 1

Accessedb




)


4/79

ii

PREFACE

This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee

TE-013, Symbols, Units and Quantities for Electrotechnology, to supersede, in part, AS 11041978,

Informative symbols for use on electrical and electronic equipment.

After consultation with stakeholders in both countries, Standards Australia and Standards New

Zealand decided to develop this Standard as an Australian Standard rather than an Australian/New

Zealand Standard.

This Standard is identical with and partially reproduced from IEC 60417-2:1998,Graphical symbols

for use on equipment, Part 2: Symbol originals, and Amendment No. 1 (2000) and Amendment No. 2

(2002).

The objective of this Standard is to provide designers, manufacturers and users of electrotechnical

equipment with uniform symbols for informative purposes to enable the operation and proper

functioning of machinery, appliances and equipment.

This Standard is part of a series, the designations and Part titles being as follows:

AS/IEC

60417.1 Part 1: Overview and application

60417.2.1 Part 2.1: General application (this Standard)

60417.2.2 Part 2.2: Audiovisual equipment

60417.2.3 Part 2.3: Telephone and communications

60417.2.4 Part 2.4: Maritime navigation

60417.2.5 Part 2.5: Home electric devices

60417.2.6 Part 2.6: Medical equipment

60417.2.7 Part 2.7: Safety aspects

The symbol originals have been presented in Parts so that users can purchase those Parts of interest.

Part 1 contains the description and purpose of the symbols as well as the full index to the symbols.

The symbols for use on equipment are not intended to be used to represent electrical components in

circuit diagrams or the like; symbols for this purpose are the subject of AS/NZS 1102, Graphical

symbols for electrotechnology(series).

The frame size for the symbols is 75 mm square. Up to three symbols are presented on each page.

As this Standard is reproduced from an international Standard, the following applies:

(a) The French text has been retained.

(b) Its number appears on the cover and title page while the international Standard number appears

only on the cover.(c) In the source text, this International Standard should read this Australian Standard.

(d) A full point substitutes for a comma when referring to a decimal marker.

The following amendments apply to the text of the Scope:

1 Addthe following at the end of the first paragraph:

This Standard provides symbols for use in general applications.

2 Add the following before the words the space in Note 1:

or symbols that are not relevant to this Part,

3 DeleteNote 2.

4 Deletethe second last paragraph.

The amendments are indicated with a bar line set against the amended text.Accessedb




)


5/79

Accessedb




)


6/79


7/79

1

www.standards.com.au Standards Aust ralia

AUSTRALIAN STANDARD

Graphical symbols for use on equipment

Part 2.1:

General application

1 Scope

This part of IEC 60417 contains graphical symbols included in IEC 60417-1 for reproductionpurposes.

NOTE 1 Generally, three of the original drawings are shown on each page. If there are unused symbol numbers,the space is left free.

NOTE 2 The original date of issue of each symbol is shown in table 1.

For rules for the application and modification of the graphical symbols, and for supplementaryinformation including references, refer to IEC 80416-1: Basic principles for graphical symbolsfor use on equipment Part 1: Creation of symbols originals.

To show the arrangement of the graphical symbol in the basic pattern, as standardized in IEC80416-1:2001, the basic pattern is included as a transparent sheet.

For each symbol the real dimensions of the width xand the height yare given in multiples ofthe nominal dimension a =50 mm.

Accessedb




)


8/79

www.standards.com.au

Standards Australia

2

Accessedb




)


9/79


Standards Australia

3

Accessedb




)


10/79


Standards Australia

4

Accessedb




)


11/79


Standards Australia

5

Accessedb




)


12/79


Standards Australia

6

Accessedb




)


13/79


Standards Australia

7

Accessedb




)


14/79


Standards Australia

8

Accessedb




)


15/79


Standards Australia

9

Accessedb




)


16/79


Standards Australia

10

Accessedb




)


17/79


Standards Australia

11

Accessedb




)


18/79


Standards Australia

12

Accessedb




)


19/79


Standards Australia

13

Accessedb




)


20/79


Standards Australia

14

Accessedb




)


21/79


Standards Australia

15

Accessedb




)


22/79


Standards Australia

16

Accessedb




)


23/79


Standards Australia

17

Accessedb




)


24/79


Standards Australia

18

Accessedb




)


25/79


Standards Australia

19

Accessedb




)


26/79


Standards Australia

20

Accessedb




)


27/79


Standards Australia

21

Accessedb




)


28/79


Standards Australia

22

Accessedb




)


29/79


Standards Australia

23

Accessedb




)


30/79


Standards Australia

24

Accessedb




)


31/79


Standards Australia

25

Accessedb




)


32/79


Standards Australia

26

Accessedb




)


33/79


Standards Australia

27

Accessedb




)


34/79


Standards Australia

28

Accessedb




)


35/79


Standards Australia

29

Accessedb




)


36/79

www.standards.com.au Standards Australia

30

Accessedb




)


37/79


Standards Australia

31

Accessedb




)


38/79


Standards Australia

32

Accessedb




)


39/79


Standards Australia

33

Accessedb




)


40/79


Standards Australia

34

Accessedb




)


41/79


Standards Australia

35

Accessedb




)


42/79


Standards Australia

36

Accessedb




)


43/79


Standards Australia

37

Accessedb




)


44/79


Standards Australia

38

Accessedb




)


45/79


Standards Australia

39

Accessedb




)


46/79


Standards Australia

40

Accessedb




)


47/79


Standards Australia

41

Accessedb




)


48/79


Standards Australia

42

Accessedb




)


49/79


Standards Australia

43

Accessedb




)


50/79


Standards Australia

44

Accessedb




)


51/79


Standards Australia

45

Accessedb




)


52/79


Standards Australia

46

Accessedb




)


53/79


Standards Australia

47

Accessedb




)


54/79


48

Accessedb




)


55/79


Standards Australia

49

Accessedb




)


56/79


Standards Australia

50

Accessedb




)


57/79


Standards Australia

51

Accessedb




)


58/79


59/79


Standards Australia

53

Accessedb




)


60/79


Standards Australia

54

Accessedb




)


61/79


55

Accessedb




)


62/79


56

Accessedb




)


63/79


57

Accessedb




)


64/79


58

Accessedb




)


65/79


Standards Australia

59

Accessedb




)


66/79


Standards Australia

60

Accessedb




)


67/79


Standards Australia

61

Accessedb




)


68/79


Standards Australia

62

Accessedb




)


69/79


Standards Australia

63

Accessedb




)


70/79


Standards Australia

64

Accessedb




)


71/79


Standards Australia

65

Accessedb




)


72/79


Standards Australia

66

Accessedb




)


73/79


Standards Australia

67

Accessedb




)


74/79


Standards Australia

68

Accessedb




)


75/79


Standards Australia

69

Accessedb




)


76/79

70

NOTES

Accessedb




)


77/79

Standards Australia

Standards Australia is an independent company, limited by guarantee, which prepares and publishes

most of the voluntary technical and commercial standards used in Australia. These standards are

developed through an open process of consultation and consensus, in which all interested parties are

invited to participate. Through a Memorandum of Understanding with the Commonwealth government,

Standards Australia is recognized as Australias peak national standards body. For further information

on Standards Australia visit us at

www.standards.org.au

Australian Standards

Aust ralian Standards are prepared by committees of experts from industry, governments, consumers

and other relevant sectors. The requirements or recommendations contained in published Standards area consensus of the views of representative interests and also take account of comments received from

other sources. They reflect the latest scientific and industry experience. Australian Standards are kept

under continuous review after publication and are updated regularly to take account of changing

technology.

International Involvement

Standards Australia is responsible for ensuring that the Australian viewpoint is considered in the

formulation of international Standards and that the latest international experience is incorporated in

national Standards. This role is vital in assisting local industry to compete in international markets.

Standards Australia represents Australia at both ISO (The International Organizationfor Standardization) and the International Electrotechnical Commission (IEC).

Electronic Standards

All Aust ralian Standards are avai lable in electronic ed itions, either downloaded individual ly from our web

site, or via On-Line and DVD subscription services. For more information phone 1300 65 46 46 or visit

Standards Web Shop at


Accessedb




)


78/79

GPO Box 5420 Sydney NSW 2001

Administration Phone (02) 8206 6000 Fax (02) 8206 6001 Email [email protected]

Customer Service Phone 1300 65 46 46 Fax 1300 65 49 49 Email [email protected]

Internetwww.standards.org.au

ISBN 0 7337 6082 1 Printed in Australia

Accessedb




)


79/79

This page has been left intentionally blank.

TYLIBRARY



)

as-nzs 60417-2!5!2004 graphical symbols for use on equipment part 2-1 gerneral application

Documents