arm 7 architecture

7/29/2019 ARM 7 ARCHITECTURE

1/22

Dr.Y.Narasimha MurthyPh.D

[email protected]

1

UNIT-II ARM 7 Microcontroller

INTRODUCTION:

The ARM was originally developed at Acorn Computers Limited of Cambridge , England,

between 1983 and 1985. It was the first RISC microprocessor developed for commercial use and

has some significant differences from subsequent RISC architectures. In 1990 ARM Limited

was established as a separate company specifically to widen the exploitation of ARM technology

and it is established as a market-leader for low-power and cost-sensitive embedded

applications. The ARM is supported by a toolkit which includes an instruction set emulator for

hardware modelling and software testing and benchmarking, an assembler, C and C++

compilers, a linker and a symbolic debugger.

The 16-bit CISC microprocessors that were available in 1983 were slower than standard memory

parts. They also had instructions that took many clock cycles to complete (in some cases, many

hundreds of clock cycles), giving them very long interrupt latencies.As a result of these

frustrations with the commercial microprocessor offerings, the design of a proprietary

microprocessor was considered and ARM chip was designed.

ARM 7TDMI-S Processor : The ARM7TDMI-S processor is a member of the ARM family of

general-purpose 32-bit microprocessors. The ARM family offers high performance for very

low-power consumption and gate count. The ARM7TDMI-S processor has a Von Neumann

architecture, with a single 32-bit data bus carrying both instructions and data. Only load, store,

and swap instructions can access data from memory. The ARM7TDMI-S processor uses a three

stage pipeline to increase the speed of the flow of instructions to the processor. This enables

several operations to take place simultaneously, and the processing, and memory systems to

operate continuously. In the three-stage pipeline the instructions are executed in three stages.

The three stage pipelined architecture of the ARM7 processor is shown in the above figure.


2/22


[email protected]

2

ARM7TDMIS stands for

T: THUMB ;

D for on-chip Debug support, enabling the processor to halt in response to a debug request,

M: enhanced Multiplier, yield a full 64-bit result, high performance

I: Embedded ICE hardware (In Circuit emulator)

S : Synthesizable

FEATURES OF ARM PROCESSORS

The ARM processors are based on RISC architectures and this architecture has provided small

implementations, and very low power consumption. Implementation size, performance, and very

low power consumption remain the key features in the development of the ARM devices.

The typical RISC architectural features of ARM are :

A large uniform register file

A load/store architecture, where data-processing operations only operate on register

contents, not directly on memory contents

Simple addressing modes, with all load/store addresses being determined from register

contents and instruction fields only uniform and fixed-length instruction fields, to

simplify instruction decode.

Control over both the Arithmetic Logic Unit (ALU) and shifter in most data-processing

instructions to maximize the use of an ALU and a shifter

Auto-increment and auto-decrement addressing modes to optimize program loops

Load and Store Multiple instructions to maximize data throughput

Conditional execution of almost all instructions to maximize execution throughput.

There are three basic instruction sets for ARM.

A 32- bit ARM instruction set A 16bit Thumb instruction set and

The 8-bit Java Byte code used in Jazelle state

The Thumb instruction set is a subset of the most commonly used32-bit ARM

instructions.Thumb instructions operate with the standard ARM register configurations

,enabling excellent interoperability between ARM and Thumb states.This Thumb state is nearly


3/22


[email protected]

3

65% of the ARM code and can provide 160%of the performance of ARM code when working

ona 16-bit memory system. This Thumb mode is used in embedded systems where memory

resources are limited. The Jazelle mode is used in ARM9 processor to work with 8-bit Java

code.

ARCHITECTURE OF ARM PROCESSORS:

The ARM 7 processor is based on Von Neman model with a single bus for both data and

instructions..( The ARM9 uses Harvard model).Though this will decrease the performance of

ARM, it is overcome by the pipe line concept. ARM uses the Advanced Microcontroller Bus

Architecture (AMBA) bus architecture. This AMBA include two system buses: the AMBA

High-Speed Bus (AHB) or the Advanced System Bus (ASB), and the Advanced Peripheral Bus

(APB).

The ARM processor consists of

Arithmetic Logic Unit (32-bit)

One Booth multiplier(32-bit)

One Barrel shifter

One Control unit

Register file of 37 registers each of 32 bits.

In addition to this the ARM also consists of a Program status register of 32 bits, Some

special registers like the instruction register, memory data read and write register andmemory address register ,one Priority encoder which is used in the multiple load and

store instruction to indicate which register in the register file to be loaded or stored and

Multiplexers etc.


4/22


[email protected]

4

ARM Registers : ARM has a total of 37 registers .In which - 31 are general-purpose registers

of 32-bits, and six status registers .But all these registers are not seen at once. The processor

state and operating mode decide which registers are available to the programmer. At any time,

among the 31 general purpose registers only 16 registers are available to the user. The remaining

15 registers are used to speed up exception processing. there are two program status registers:

CPSR and SPSR(the current and saved program status registers, respectively

In ARM state the registers r0 to r13are orthogonalany instruction that you can apply to r0you

can equally well apply to any of the other registers.

The main bank of 16 registers is used by all unprivileged code. These are the User mode

registers. User mode is different from all other modes as it is unprivileged. In addition to this

register bank ,there is also one 32-bit Current Program status Register(CPSR)


5/22


[email protected]

5

In the 15 registers ,the r13 acts as a stack pointer register and r14 acts as a link register and r15

acts as a program counter register.

Register r13 is the sp register ,and it is used to store the address of the stack top. R13 is used by

the PUSH and POP instructions in T variants, and by the SRS and RFE instructions from

ARMv6.

Register 14 is the Link Register(LR). This register holds the address of the next instruction after

a Branch and Link (BL or BLX) instruction, which is the instruction used to make a subroutine

call. It is also used for return address information on entry to exception modes. At all other times,

R14 can be used as a general-purpose register.

Register 15 is the Program Counter (PC). It can be used in most instructions as a pointer to the

instruction which is two instructions after the instruction being executed.

The remaining 13 registers have no special hardware purpose.

CPSR: The ARM core uses the CPSR register to monitor and control internal operations. The

CPSR is a dedicated 32-bit register and resides in the register file. The CPSR is divided into

four fields, each of 8 bits wide : flags, status, extension, and control. The extension and status

fields are reserved for future use. The control field contains the processor mode, state, and

interrupt mask bits. The flags field contains the condition flags. The 32-bit CPSR register is

shown below.


6/22


[email protected]

6

Processor Modes:There are seven processor modes .Six privileged modes abort, fast interrupt

request, interrupt request, supervisor, system, and undefined and one non-privileged mode

called user mode.

The processor enters abort mode when there is a failed attempt to access memory. Fast interrupt

request and interrupt request modes correspond to the two interrupt levels available on the ARM

processor. Supervisor mode is the mode that the processor is in after reset and is generally the

mode that an operating system kernel operates in. System mode is a special version of user mode

that allows full read-write access to the CPSR. Undefined mode is used when the processor

encounters an instruction that is undefined or not supported by the implementation. User mode is

used for programs and applications.

Banked Registers : Out of the 32 registers , 20 registers are hidden from a program at different

times. These registers are called banked registers and are identified by the shading in the

diagram. They are available only when the processor is in a particular mode; for example, abort

mode has banked registers r13_abt , r14_abt and spsr _abt. Banked registers of a particular

mode are denoted by an underline character post-fixed to the mode mnemonic or _mode.

When the T bit is 1, then the processor is in Thumb state. To change states the core executes a

specialized branch instruction and when T= 0 the processor is in ARM state and executes ARM

instructions. There are two interrupt request levels available on the ARM processor core

interrupt request (IRQ) and fast interrupt request (FIQ).

V, C , Z , N are the Condition flags .

V (oVerflow) : Set if the result causes a signed overflow

C (Carry) : Is set when the result causes an unsigned carry

Z (Zero) : This bit is set when the result after an arithmetic operation is zero, frequently

used to indicate equality

N (Negative) : This bit is set when the bit 31 of the result is a binary 1.

PIPE LINE : Pipeline is the mechanism used by the RISC processor to execute instructions at

an increased speed. This pipeline speeds up execution by fetching the next instruction while

other instructions are being decoded and executed. During the execution of an instruction ,the

processor Fetches the instruction .It means loads an instruction from memory.And decodes the


7/22


[email protected]

7

instruction i.e identifies the instruction to be executed and finally Executes the instruction and

writes the result back to a register.

The ARM7 processor has a three stage pipelining architecture namely Fetch , Decode and

Execute.And the ARM 9 has five stage Pipe line architecture.The three stage pipelining is

explained as below.

To explain the pipelining ,let us consider that there are three instructions Compare, Subtract and

Add.The ARM7 processor fetches the first instruction CMP in the first cycle and during the

second cycle it decodes the CMP instruction and at the same time it will fetch the SUB

instruction. During the third cycle it executes the CMP instruction , while decoding the SUB

instruction and also at the same time will fetch the third instruction ADD. This will improve the

speed of operation. This leads to the concept of parallel processing .This pipeline example is

shown in the following diagram.


8/22


[email protected]

8

As the pipeline length increases, the amount of work done at each stage is reduced, which allows

the processor to attain a higher operating frequency. This in turn increases the performance. One

important feature of this pipeline is the execution of a branch instruction or branching by the

direct modification of the PCcauses the ARM core to flush its pipeline.

Exceptions, Interrupts, and the Vector Table :

Exceptions are generated by internal and external sources to cause the ARM processor to handle

an event, such as an externally generated interrupt or an attempt to execute an Undefined

instruction. The processor state just before handling the exception is normally preserved so that

the original program can be resumed after the completion of the exception routine. More than

one exception can arise at the same time.ARM exceptions may be considered in three groups

1. Exceptions generated as the direct effect of executing an instruction.Software interrupts,

undefined instructions (including coprocessor instructions where the requested coprocessor is

absent) and prefetch aborts (instructions that are invalid due to a memory fault occurring during

fetch) come under this group.

2. Exceptions generated as a side-effect of an instruction.Data aborts (a memory fault during a

load or store data access) are in this group.

3. Exceptions generated externally, unrelated to the instruction flow.Reset, IRQ and FIQ are in

this group.

The ARM architecture supports seven types of exceptions.

i.Reset

ii.Undefined Instruction

iii.Software Interrupt(SWI)

iv. Pre-fetch abort(Instruction Fetch memory fault)

v.Data abort (Data access memory fault)

vi. IRQ(normal Interrupt)

vii. FIQ (Fast Interrupt request).

When an Exception occurs , the processor performs the following sequence of actions:

It changes to the operating mode corresponding to the particular exception.

It saves the address of the instruction following the exception entry instruction in r14 of the

new mode.


9/22


[email protected]

9

It saves the old value of the CPSR in the SPSR of the new mode.

It disables IRQs by setting bit 7 of the CPSR and, if the exception is a fast interrupt, disables

further fast interrupts by setting bit 6 of the CPSR.

It forces the PC to begin executing at the relevant vector address

Excdption / Interrupt Name Address High Address

Reset RESET 0X00000000 0Xffff0000

Undefined Instruction UNDEF 0X00000004 0Xffff0004

Software Interrupt SWI 0X00000008 0Xffff0008

Pre-fetch Abort PABT 0X0000000C 0Xffff000c

Data Abort DABT 0X00000010 0Xffff0010

Reserved --- 0X00000014 0Xffff0014

Interrupt Request IRQ 0X00000018 0Xffff0018

Fast Interrupt Request FIQ 0X0000001C 0Xffff001c

The exception Vector table shown above gives the address of the subroutine program to be

executed when the exception or interrupt occurs. Each vector table entry contains a form of

branch instruction pointing to the start of a specific routine.

Reset vector is the location of the first instruction executed by the processor when power isapplied. This instruction branches to the initialization code.

Undefined instruction vectoris used when the processor cannot decode an instruction.

Software interrupt vectoris called when you execute a SWI instruction. The SWI instruction is

frequently used as the mechanism to invoke an operating system routine.

Pre-fetch abort vectoroccurs when the processor attempts to fetch an instruction from an address

without the correct access permissions. The actual abort occurs in the decode stage.

Data abort vector is similar to a prefetch abort but is raised when an instruction attempts toaccess data memory without the correct access permissions.

Interrupt request vector is used by external hardware to interrupt the normal execution flow ofthe processor. It can only be raised if IRQs are not masked in the CPSR.

ARM Processor Families

There are various ARM processors available in the market for different application .These are

grouped into different families based on the core .These families are based on the ARM7,


10/22


[email protected]

10

ARM9, ARM10, and ARM11 cores. The numbers 7, 9, 10, and 11 indicate different core

designs. The ascending number indicates an increase in performance and sophistication.

Though ARM 8 was introduced during 1996, it is no more available in the market. The

following table gives a brief comparison of their performance and available resources.

The ARM7 core has a Von Neumannstyle architecture, where both data and instructions use the

same bus. The core has a three-stage pipeline and executes the architecture ARMv4T instruction

set. The ARM7TDMI was introduced in 1995 by ARM. It is currently a very popular core and is

used in many 32-bit embedded processors.

The ARM9 family was released in 1997. It has five stage pipeline architecture .Hence , the

ARM9 processor can run at higher clock frequencies than the ARM7 family. The extra stages

improve the overall performance of the processor. The memory system has been redesigned to

follow the Harvard architecture, with separate data and instruction .buses. The first processor in

the ARM9 family was the ARM920T, which includes a separate D + Icache and an MMU. This

processor can be used by operating systems requiring virtual memory support. ARM922T is a

variation on the ARM920T but with half the D +Icache size.

The latest core in the ARM9 product line is the ARM926EJ-S synthesizable processor core,

announced in 2000. It is designed for use in small portable Java-enabled devices such as 3G

phones and personal digital assistants (PDAs).

The ARM10 was released in 1999 . It extends the ARM9 pipeline to six stages. It also supports

an optional vector floating-point (VFP) unit, which adds a seventh stage to the ARM10 pipeline.

The VFP significantly increases floating-point performance and is compliant with the IEEE

754.1985 floating-point standard.

The ARM1136J-S is the ARM11 processor released in the year 2003 and it is designed for high

performance and power efficient applications. ARM1136J-S was the first processor

implementation to execute architecture ARMv6 instructions. It incorporates an eight-stage

pipeline with separate load store and arithmetic pipelines.

A brief comparison of different ARM families is presented below.


11/22


[email protected]

11

ARM

Family

Year of

Release

Architecture Pipeline Operational

Frequency

Multiplier MIPS

ARM7 1995 Von Neumann 3 stage 80 M.Hz 8x32 0.97

ARM9 1997 Harvard 5 stage 150M.Hz 8x32 1.1



ARM INSTRUCTION SET

ARM instructions process data held in registers and only access memory with load and store

instructions. ARM instructions commonly take two or three operands.For example ,the ADD instruction adds the two values stored in registers r1and r2(the sourceregisters). It stores the result to register r3(the destination register). ADD r3, r1, r2

ARM instructions are classified into data processing instructions, branch instructions, load-store

instructions, software interrupt instruction, and program status register instructions.

Data Processing Instructions :

The data processing instructions manipulate data within registers. They are move instructions,

Arithmetic instructions, logical instructions, comparison instructions, and multiply instructions.

Most data processing instructions can process one of their operands using the barrel shifter.

Data processing instructions are processed within the arithmetic logic unit (ALU). A unique and

powerful feature of the ARM processor is the ability to shift the 32-bit binary pattern in one of

the source registers left or right by a specific number of positions before it enters the ALU. This

shift increases the power and flexibility of many data processing operations .

There are data processing instructions that do not use the barrel shift, for example, the MUL(multiply), CLZ (count leading zeros), and QADD (signed saturated 32-bit add) instructions.

i.Move Instructions : Move instruction copies R into a destination registerRd, where Ris a

register or immediate value. This instruction is useful for setting initial values and transferring

data between registers.


12/22


[email protected]

12

Example1 : PRE r5 = 5

r7 = 8

MOV r7, r5 ;

POST r5 = 5

r7 = 5

The MOV instruction takes the contents of register r5and copies them into register r7.

Example 2: MOVS r0, r1, LSL #1

MOVS instruction shifts registerr1 left by one bit

Arithmetic Instructions : The arithmetic instructions implement addition and subtraction of

32-bit signed and unsigned values. the various addition and subtraction instructions are given intable below.

SUB r0, r1, r2 ; This subtract instruction subtracts a value stored in register r2from a value

stored in register r1. The result is stored in register r0.

RSB r0, r1, #0 ; This reverse subtract instruction (RSB) subtracts r1from the constant value #0,

writing. the result to r0. You can use this instruction to negate numbers.

SUBS r1, r1, #1 ; The SUBS instruction is useful for decrementing loop counters. In thisexample we subtract the immediate value one from the value one stored in

register r1. The result value zero is written to register r1.

Logical Instructions : TheseLogical instructions perform bitwise logical operations on the two

source registers.


13/22


[email protected]

13

BIC r0, r1, r2 ; BIC, carries out a logical bit clear. register r2contains a binary pattern where

every binary 1 in r2 clears a corresponding bit location in register r1. This instruction isparticularly useful when clearing status bits and is frequently used to change interrupt masks in

the cpsr.

Comparison Instructions : The comparison instructions are used to compare or test aregister with a 32-bit value. This instruction affects only CPSR register flags.

Branch Instructions: A branch instruction changes the normal flow of execution of a main

program or is used to call a subroutine routine. This type of instruction allows programs to have

subroutines, if-then-else structures, and loops. The change of execution flow forces the programcounterpc to point to a new address.Example 1: B forward ; (unconditional branch to forward)

ADD r1, r2, #4 ;

ADD r0, r6, #2 ;

ADD r3, r7, #4 ;

forward SUB r1, r2, #4 ;

Similarly Backward branch :


14/22


[email protected]

14

backward : ADD r1, r2, #4 ;

SUB r1, r2, #4 ;

ADD r4, r6, r7 ;

B backward ; branch to the target backward.

The branch with link, or BL, instruction is similar to the B instruction but overwrites the

link register lrwith a return address. It performs a subroutine call.

BL subroutine ; branch to subroutine

CMP r1, #5 ; compare r1 with 5

MOVEQ r1, #0 ; if (r1==5) then r1 = 0 :

Subroutine

MOV pc, lr ; return by moving pc = lr

The Branch Exchange (BX) and Branch Exchange with Link (BLX) are the third type of branch instruction.

The BX instruction uses an absolute address stored in register Rm. It is primarily used to branch to and

from Thumb code. The Tbit in the cpsr is updated by the least significant bit of the branch register.

Similarly the BLX instruction updates the Tbit of the cpsrwith the least significant bit and additionally

sets the link register with the return address.

The details of the branch instructions are given in the table above.

Load-Store Instructions : Load-store instructions transfer data between memory and processor

registers. There are three types of load-store instructions:

Single-register transfer

Multiple-register transfer, and


15/22


[email protected]

15

Swap.

Single-Register Transfer : These instructions are used for moving a single data item in and out of a

register. The data types supported are signed and unsigned words (32-bit), half-words (16-bit), and

bytes. Ex1: STR r0, [r1] ; = STR r0, [r1, #0] ; store the contents of register r0 to the

memory address pointed to by register r1.

Ex2 : LDR r0, [r1] ; = LDR r0, [r1, #0] ; load register r0 with the contents of the

memory address pointed to by register r1.

Multiple-Register Transfer : Load-store multiple instructions can transfer multiple registers

between memory and the processor in a single instruction. The transfer occurs from a base

address register Rnpointing into memory. Multiple-register transfer instructions are more

efficient than single-register transfers for moving blocks of data around memory and saving and

restoring context and stacks.

Load-store multiple instructions can increase interrupt latency. ARM implementations do not

usually interrupt instructions while they are executing. For example, on an ARM7 a load

multiple instruction takes 2 + N.tcycles, where Nis the number of registers to load and t is the

number of cycles required for each sequential access to memory. If an interrupt has been raised,

then it has no effect until the load-store multiple instruction is complete.

Example 1: LDMIA r0!, {r1-r3} ; In this example, register r0 is the base register Rn and is

followed by !, indicating that the register is updated after the instruction is executed. In this case

the range is from register r1to r3.

Example 2 : LDMIB : load multiple and increment before

Ex 3: LDMIB r0!, {r1-r3} ;

Ex 4 : LDMDA r0!, {r1-r3}


16/22


[email protected]

16

Stack Operations : The ARM architecture uses the load-store multiple instructions to carry out

stack operations. The pop operation (removing data from a stack) uses a load multiple

instruction; similarly, the push operation (placing data onto the stack) uses a store multiple

instruction.

A stack is either ascending (A) or descending (D). Ascending stacks grow towards higher

memory addresses; in contrast, descending stacks which grow towards lower memory addresses.

When a full stack (F)is used , the stack pointer sppoints to an address that is the last used or full

location (i.e., sppoints to the last item on the stack). In contrast, if an empty stack (E) is used ,

the sppoints to an address that is the first unused or empty location (i.e., it points after the last

item on the stack).

Example1 : The STMFD instruction pushes registers onto the stack, updating the sp.

STMFD sp! , {r1,r4}; Store Multiple Full Descending Stack

PRE r1 = 0x00000002

r4 = 0x00000003

sp = 0x00080014

POST r1 = 0x00000002

r4 = 0x00000003

sp = 0x0008000c.

The stack operation is shown by the following diagram.

Example2: The STMED instruction pushes the registers onto the stack but updates register spto

point to the next empty location as shown in the below diagram..


17/22


[email protected]

17

PRE r1 = 0x00000002

r4 = 0x00000003

sp = 0x00080010

STMED sp! , {r1,r4} ; Store Multiple Empty Descending Stack

POST r1 = 0x00000002

r4 = 0x00000003

sp = 0x00080008

This operation is explained in the following figure.

Swap Instruction :

The Swap instruction is a special case of a load-store instruction. It swaps (Similar to exchange)

the contents of memory with the contents of a register. This instruction is an atomic operation

it reads and writes a location in the same bus operation, preventing any other instruction from

reading or writing to that location until it completes.Swap cannot be interrupted by any other

instruction or any other bus access. So, the system holds the bus until the transaction is

complete.

Ex 1: SWP : Swap a word between memory and a registertmp = mem32[Rn]mem32[Rn] =Rm

Rd = tmp

Ex2 : SWPB Swap a byte between memory and a register tmp = mem8[Rn]

mem8[Rn] =Rm


18/22


[email protected]

18

Rd = tmp.

Ex 3: SWP r0, r1, [r2] ; The swap instruction loads a word from memory into registerr0 and overwrites the memory with register r1.

Software Interrupt Instruction : A software interrupt instruction (SWI) is used to generate a

software interrupt exception, which can be used to call operating system routines.When the

processor executes an SWI instruction, it sets the program counter pc to the offset 0x8 in the

vector table. The instruction also forces the processor mode to SVC, which allows an operating

system routine to be called in a privileged mode. Each SWI instruction has an associated SWI

number, which is used to represent a particular function call or feature.

Ex: 0x00008000 SWI 0x123456

Here 0x123456, is the SWI number used by ARM toolkits as a debugging SWI. Typically

the SWI instruction is executed in user mode.

Program Status Register Instructions : There are two instructions available to directly control

a program status register (PSR). The MRS instruction transfers the contents of either the CPSR

or SPSRinto a register.Similarly the MSR instruction transfers the contents of a register intothe CPSR or SPSR .These instructions together are used to read and write the CPSRand

SPSR.

MRS : copy program status register to a general-purpose register , Rd= PSR

MSR : move a general-purpose register to a program status register, PSR[field]=Rm

MSR : move an immediate value to a program status register,PSR[field]=immediate

Ex : MRS r1, CPSR

BIC r1, r1, #0x80 ; 0b01000000

MSR CPSR_C, r1.

The MSR first copies the CPSRinto register r1. The BIC instruction clears bit 7 of r1. Register

r1is then copied back into the CPSR, which enables IRQ interrupts. Here the code preserves all

the other settings in the CPSR intact and only modifies the Ibit in the control field.


19/22


[email protected]

19

Loading Constants : In ARM instruction set there are no instructions to move the 32-bit

constant into a register. Since ARM instructions are 32 bits in size, they obviously cannot

specify a general 32-bit constant. To overcome this problem .two pseudo instructions are

provided to move a 32-bit value into a register.

LDR : load constant pseudo instruction Rd= 32-bit constant.

ADR : load address pseudo instruction Rd=32-bit relative address.

The first pseudo instruction writes a 32-bit constant to a register using whatever instructions are

available.

The second pseudo instruction writes a relative address into a register, which will be encoded

using a PC -relative expression.

Example 2: LDR r0, [pc, #constant_number-8-{PC}]

constant _number DCD 0xff00ffff.

Here the LDR instruction loads a 32-bit constant 0xff00ffff into register r0.

Example 3: The same constant can be loaded into the register r0 using the MVN instruction also.

MVN r0, #0x00ff0000

After execution r0 = 0xff00ffff.

Introduction to Thumb instruction set : Thumb encodes a subset of the 32-bit ARM

instructions into a 16-bit instruction set space. Since Thumb has higher performance than ARM

on a processor with a 16-bit data bus, but lower performance than ARM on a 32-bit data bus, use

Thumb for memory-constrained systems. Thumb has higher code densitythe space taken up in

memory by an executable programthan ARM. For memory-constrained embedded systems,

for example, mobile phones and PDAs, code density is very important. Cost pressures also limit

memory size, width, and speed.

Thumb execution is flagged by the T bit (bit [5] ) in the CPSR. A Thumb implementation of the

same code takes up around 30% less memory than the equivalent ARM implementation. Even

though the Thumb implementation uses more instructions ; the overall memory footprint is

reduced. Code density was the main driving force for the Thumb instruction set. Because it was

also designed as a compiler target, rather than for hand-written assembly code. Below example

explains the difference between ARM and Thumb code


20/22


[email protected]

20

From the above example it is clear that the Thumb code is more denser than the ARM code.

Exceptions generated during Thumb execution switch to ARM execution before executing the

exception handler . The state of the T bit is preserved in the SPSR, and the LR of the exception

mode is set so that the normal return instruction performs correctly, regardless of whether the

exception occurred during ARM or Thumb execution.

In Thumb state, all the registers can not be accessed . Only the low registers r0 to r7 can be

accessed. The higher registers r8 to r12 are only accessible with MOV, ADD, or CMP

instructions. CMP and all the data processing instructions that operate on low registers update

the condition flags in the CPSR

The list of registers and their accessibility in Thumb mode are shown in the following table..

S.No Registers Access

1 r0r7 Fully accessible

2 r8r12 Only accessible by MOV ,ADD &CMP

3 r13SP Limited accessibility

4 r14 lr Limited accessibility

5 r15 PC Limited accessibility

6 CPSR Only indirect access

7 SPSR No access


21/22


[email protected]

21

Form the above discussion, it is clear that there are no MSR and MRS equivalent Thumb

instructions. To alter the CPSR or SPSR , one must switch into ARM state to use MSR and

MRS. Similarly, there are no coprocessor instructions in Thumb state. You need to be in ARM

state to access the coprocessor for configuring cache and memory management.

ARM-Thumb interworking is the method of linking ARM and Thumb code together for both

assembly and C/C++. It handles the transition between the two states. To call a Thumb routine

from an ARM routine, the core has to change state. This is done with the T bit of CPSR . The

BX and BLX branch instructions cause a switch between ARM and Thumb state while branching

to a routine. The BX lrinstruction returns from a routine, also with a state switch if necessary.

The data processing instructions manipulate data within registers. They include move

instructions, arithmetic instructions, shifts, logical instructions, comparison instructions, and

multiply instructions. The Thumb data processing instructions are a subset of the ARM data

processing instructions.

Exs : ADC : add two 32-bit values and carry Rd = Rd + Rm + C flag

ADD : add two 32-bit values Rd = Rn + immediate

Rd = Rd + immediateRd = Rd + Rm

AND : logical bitwise AND of two 32-bit values Rd = Rd & RmASR : arithmetic shift right Rd = Rm_immediate,

C flag= Rm[immediate 1]

Rd = Rd_Rs, C flag = Rd[Rs - 1]BIC : logical bit clear (AND NOT) of two 32-bit Rd = Rd AND

NOT(Rm)values

CMN : compare negative two 32-bit values Rn + Rm sets flagsCMP : compare two 32-bit integers Rnimmediate sets flags RnRm sets flags

EOR : logical exclusive OR of two 32-bit values Rd = Rd EOR Rm

LSL : logical shift left Rd = Rm_ immediate,C flag= Rm[32 immediate]

Rd = Rd_Rs, C flag = Rd[32 Rs]

LSR : logical shift right Rd = Rm_ immediate,

C flag = Rd [immediate 1]Rd = Rd_ Rs, C flag = Rd[Rs 1]

MOV : move a 32-bit value into a register Rd = immediate


22/22


[email protected]

22

Rd = Rn

Rd = Rm

MUL : multiply two 32-bit values Rd = (Rm * Rd)[31:0]MVN : move the logical NOT of a 32-bit value into a register Rd = NOT(Rm)

NEG : negate a 32-bit value Rd = 0 RmORR : logical bitwise OR of two 32-bit values Rd = Rd OR RmROR : rotate right a 32-bit value Rd = Rd RIGHT_ROTATE Rs,

C flag= Rd[Rs1]

SBC : subtract with carry a 32-bit value Rd = Rd Rm NOT(C flag)SUB : subtract two 32-bit values Rd = Rn immediate

Rd = Rd immediate

Rd = Rn Rm

sp = sp (immediate_2)TST : test bits of a 32-bit value Rn AND Rm sets flags

Note : Thumb deviates from the ARM style in that the barrel shift operations (ASR, LSL, LSR,and ROR) are separate instructions.

Thankful to the following people for their invaluable information .

References : 1.ARM System Developers Guide Designing and Optimizing System SoftwareAndrew N. Sloss ,Dominic Symes and Chris Wright.

2. ARM-System on-Chip ArchitectureSteve Furber.

3.ARM Architecture Reference Manual Copyright 1996-1998, 2000, 2004, 2005ARM Limited.

arm 7 architecture

Documents