apron front stainless steel sink fireclay...
TRANSCRIPT
PAGE 1
Fireclay SinkInstallation Instructions
PAGE 1
Apron Front Stainless Steel SinkInstallation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Apron Front Stainless Steel SinkInstallation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Apron Front Stainless Steel SinkInstallation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
30" Single Bowl Fireclay Kitchen Sink
l (stone, marble and granite silicone caulk are recommended)
(1 ” (32mm) Max Thickness)
(recommended by countertop manufacturer)(not permanent marker)
Before You Start
l
Recommended Tools & Materials (Not Included)
24" Single Bowl Fireclay Kitchen Sink 33" Single Bowl Fireclay Kitchen Sink
Contact Superior Sinks at (678) 445-4638 or visit www.superiorsinks.com. Copyright ©2018. All rights reserved.
• Superior recommends that all fireclay sinks should be installed by an experienced, professional installer.
cabinet maker with the actual sink to be installed prior to cabinet fabrication.
Superior is not responsible for sink or countertop if damag ed during installation. Be sure to inspect the sink for damageprior to beginning installation.
•
• Metal edges may be sharp – use caution when handling.
Follow all local plumbing and building codes.•
• IMPORTANT: Superior does not offer the cutout template for fireclay sinks. It is recommended that you discuss with yourinstaller and agree that the finished appearance is the desired effect. Superior is not responsible for improper sink o rcountertop installations.
• Superior fireclay sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
A custom sink base cabinet and support framing is required for proper installation. Superior recommends providing the•
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into th e support framing. Failure of this step can lead to productdamage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing,bu t short enough not to go through the walls of adjacent cabinets.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
2: P
REP
CO
UN
TER
TOP
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
OUTLINE FOR FIRECLAY SINK CUTOUT
1.
2.
3.
1. Ask the proffesional installer to make a cutout outline based on thefireclay sink; position it on the bottom of the countertop, flush to thefront and centered; secure with tape.
Trace the cutout outline and remove. Try fit the sink to verify themeasurements.
Following the countertop manufacturer’s instructions, carefully cut thecountertop on the traced line.
OUTLINE FOR FIRECL AYSINK CUTOUT
2.
3.
3: I
NST
ALL
SU
PPO
RT
FRA
MIN
G
5. Cut (4) lengths of support framing to extend from the bottom of thehorizontal supports to the floor of the cabinet.
Secure the vertical supports with construction adhesive and screws(not provided).
SUPPORT FRAMING6.
SUPPORTING BOARD
7. Cut a supporting board with the outlet holes for the drain and watersupply system (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screwsare long enough to secure the support framing, but short enough not to gothrough the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required forproper installation. Ensure that the whole supporting system could bear the entire load of the fireclay sink.
IMPORTANT: Make sure the top of the sink does not extend above the top of thecabinet; otherwise it will interfere with countertop installation.
1. Cut two lengths of support framing to extend horizontally along theinside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rimwill sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (notprovided).
Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
Mark the fireclay cut out on the painter’s tape using the dimension of the fireclay sink’s apron front.
Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and levelBEFORE installing the sink.
IMPORTANT: Superior recommends providing the cabinet maker with the actualsink prior to cabinet fabrication. Before installing the sink, verify that the distancefrom the top of the doors to the top of the cabinet is greater than the apron front of the fireclay sink.
IMPORTANT: Double check the measurement of the cabinet cutout andmake any necessary adjustments by either adding filler strips or sanding theopening.
Installation InstructionsApron Front Stainless Steel Sink
Installation Instructions1:
PR
EPA
RE
THE
BA
SE C
AB
INET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel SinkInstallation Instructions
1: P
REP
AR
E TH
E B
ASE
CA
BIN
ET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and make any necessary adjustments by either adding filler strips or sanding the opening.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: P
REP
CO
UN
TER
TOP
1. Position the template (provided with your sink) on the bottom of the countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THESINK FITS FLUSH WITH THE TOP OF THE CABINET
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: IN
STA
LL S
UPP
OR
T FR
AM
ING
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: P
REPA
RE TH
E BA
SE C
ABI
NET
1. Apply painter’s tape to the cabinets for marking and cutting purposes. This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual sink prior to cabinet fabrication. Before installing the sink, verify that the distance from the top of the doors to the top of the cabinet is greater than the apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRONFRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but short enough not to go through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
3: IN
STA
LL S
UPPO
RT F
RAM
ING
2: P
REP
CO
UNTE
RTO
P 1. Position the template (provided with your sink) on the bottom of the
2.measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the countertop on the traced line.
OUTLINE FOR APRONFRONT SINK CUTOUT
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
Fireclay Sink
Contact Superior Sinks at (678) 445-4638 or visit www.superiorsinks.com. Copyright ©2018. All rights reserved.
Fireclay SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
KApron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
Apron Front Stainless Steel SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
1. Lower the sink onto the supports and verify the sink is supported bythe frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
5. Immediately remove excess sealant.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Superior is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
Apron Front Stainless Steel SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.4170 JVL Industrial Park DriveMarietta, GA 30066(678) 445-4638
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
5: IN
STA
LL C
oU
NTE
RTo
P
4
Apron Front Stainless Steel SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
Apron Front Stainless Steel SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
Apron Front Stainless Steel SinkInstallation Instructions
PAGE 3
4: IN
STA
LL T
HE
SIN
K
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SILICONE SEALANT AFTER CLEANING THESINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETSTHE COUNTERTOP AND CABINET.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
5: IN
STA
LL C
OU
NTE
RTO
P
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this with your installer and agree that this finished appearance is the desired effect. Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
4: IN
STA
LL TH
E SI
NK
1. Lower the sink onto the supports and verify the sink is supported by the frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to beginning installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and back of the sink.
3. Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
5: IN
STA
LL C
OUN
TERT
OP
APPLY SEALANT AFTER CLEANING THE SINK EDGE AND COUNTERTOP
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel SinkInstallation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
with your installer and agree that this �nished appearance is the desired e�ect.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.820 Shallowford RdKennesaw, GA 30144(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:Soleil Sink Company Inc.4170 JVL Industrial Park DriveMarietta, GA 30066(678) 445-4638
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
6: F
INA
L ST
EPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.superiorsinks.com.
APPLY SEALANT WHERE THE SINK MEETS THE COUNTERTOP AND CABINET.
1. Clean the bottom of the countertop and the top flange (or lip) of the sink with denatured alcohol.
Apply a narrow bead of sealant around the side and back of the sink.
Carefully position and secure the sink to the countertop following the manufacturer’s instructions.
Apply a thin bead of sealant where the sink meets the countertop and cabinet.
2.
3.
.
Contact Superior Sinks at (678) 445-4638 or visit www.superiorsinks.com. Copyright ©2018. All rights reserved.
IMPORTANT: Superior does not offer the cutout template for fireclay sinks.It is recommended that you discuss this with your installer and agree that
this finished appearance is the desired effect.Superior is not responsible for improper sink or countertop installations.
IMPORTANT: Superior apron front sinks should only be fastened to a solidsurface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the cabinet; otherwise it will interfere with countertop installation.
Limited 10-Year Sink Warranty
This product has been manufactured and tested to the highest quality standards by Superior. We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTYSuperior warranties this product against defects due to material or craftsmanship error during the warranty period: Superior will provide replacement parts at no charge, or at its option, replace any product or part of the product that is deemed defective, under normal installation, use, service and maintenance. If Superior is unable to provide a replacement and repair is not practical or cannot be made in a timely fashion, Superior may elect to refund the purchase price in exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Superior products will require light maintenance to ensure proper function. We provide you with complete knowledge to perform this maintenance and can also recommend resources if you are unable to fulfill this service.
NON-APPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Superior is not liable for incidental, consequential or special damages associated with the return, replacement, installation or use of your prod-uct. This includes freight costs, cartridge replacement, labor, travel time, lost profit, home damages and other contingent liabilities and costs (including, without limitation, costs associated with experts, investigations, analyses, attorneys and other professionals and services). The Superior warranty is a comprehensive and explicit limit of liability and all items outside of it are not addressable by or the responsibility of Superior. Certain states have variances regarding implied warranties and in those situations we remain fully compliant.
Superior makes no implication that products comply with any or all local building or plumbing codes. It is the consumer’s responsibility to determine local code compliance. This warranty extends to the original purchaser and first consumer.
For additional information or warranty issues visit www.superiorsinks.com or contact Superiordirectly: PHONE (678) 445-4638
PAGE 4
Contact Superior at (678) 445-4638 or visit www.iptsink.com. Copyright ©2016, Superior Inc. All rights reserved.
A. Superior will not be responsible for product failures due to lack of maintenance or proper use. Pleaseread your care and maintenance documentation to determine the limits of proper use. Superior will not beheld responsible for any damage resulting from abuse like heavy impact or dropped objects.B. The original sales receipt, order number, and/or proof of purchase must be presented at the time of the warranty claim, without exception, for this warranty to be applied to all Superior products.C. Superior recommends installing all Superior products with a licensed, professional plumber. Superior willnot be held responsible for any damage or product failure due to improper installation, misuse, or failure touse a licensed professional.D. Commercial use will automatically void this warranty.
Contact Superior Sinks at (678) 445-4638 or visit www.superiorsinks.com. Copyright ©2018. All rights reserved.