apprenticeship training standards refrigeration and air ... · (3) despite subsection (1), if a...
TRANSCRIPT
Apprenticeship Training Standard
Refrigeration andAir Conditioning Systems
Mechanic – Branch 1
Trade Code: 313A
Development Date: September 2004
This document is the property of the apprentice named inside and represents the official record of his/her training
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
CONTENTS PAGE
Apprenticeship Program Regulation ..............................................................................................2
Competency Analysis Profile .......................................................................................................... 5
Preface ........................................................................................................................................... 11
Definitions ..................................................................................................................................... 12
Important Directions to the Apprentice ......................................................................................... 15
Important Directions for the Sponsor/Employer & Supervisor/Trainer........................................ 15
Notice/Declaration for Collection of Personal Information .......................................................... 16
Roles and Responsibilities of Apprentice, Sponsor/Employer and Supervisor/Trainer ............... 17
Skill Set Unit Completion Form.................................................................................................... 19
SKILL SETS
6238.00 Protect Self and Others .......................................................................................... 20
6239.00 Plan and Prepare for Installation, Maintenance, or Service
of Refrigeration and Air Cooling (R&AC) System............................................... 25 6240.00 Install and Start Up Air Cooling (AC) and Heat Pump (HP) ................................ 34
6241.00 Service or Maintain Air Cooling (AC) and Heat Pump (HP) ................................ 42
6242.00 Install and Commission Refrigeration and Air Conditioning (R&AC) System …53
6243.00 Maintain Refrigeration and Air Conditioning (R&AC) System ........................... 60
6244.00 Service Refrigeration and Air Conditioning (R&AC) System.............................. 64
6245.00 Perform Customer Service .................................................................................... 72
Apprentice Record......................................................................................................................... 75
Apprentice Completion Form........................................................................................................ 78
1
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
ONTARIO REGULATION 75/05
made under the
TRADES QUALIFICATION AND APPRENTICESHIP ACT
Made: March 2, 2005 Filed: March 4, 2005
Printed in The Ontario Gazette: March 19, 2005
REFRIGERATION AND AIR CONDITIONING SYSTEMS MECHANIC
Definition
1. In this Regulation, “certified trade” means the trade of Refrigeration and Air Conditioning Systems Mechanic.
Designation as certified trade
2. The trade of Refrigeration and Air Conditioning Systems Mechanic is designated as a certified trade for the purposes of the Act and shall consist of the following two branches:
1. Refrigeration and air conditioning systems mechanic. 2. Residential air conditioning systems mechanic.
Scope of trade
3. (1) The performance of any of the following functions constitutes work that is part of the certified trade: 1. Plan, prepare and lay out the system. 2. Install and start up the system and verify the operation and function of the system.
3. Install and connect piping for the purpose of conveying all types of refrigerant used for both primary and secondary cooling.
4. Maintain, service, repair and replace system components and accessories, including the electrical and electronic components of the system.
5. Service, test, adjust, commission and decommission the system. (2) A person who holds a certificate of qualification as a refrigeration and air conditioning systems mechanic, and any
other person authorized under the Act to work as a refrigeration and air conditioning systems mechanic, may perform the functions described in subsection (1) with respect to any cooling system or heating-cooling combination system that is installed and used in a residential, industrial, commercial or institutional setting.
(3) A person who holds a certificate of qualification as a residential air conditioning systems mechanic, and any other person authorized under the Act to work as a residential air conditioning systems mechanic, may perform the functions described in subsection (1) only with respect to residential air conditioning systems that meet the following requirements:
1. The system shall be installed as an independent unit in a residential family dwelling. 2. The system shall operate at no more than 240 volts single-phase power with a maximum branch circuit capacity of
60 amps, a maximum cooling capacity of 60,000 British thermal units per hour and a saturated suction temperature above 2 degrees Celsius (35 degrees Fahrenheit) in the cooling cycle.
(4) For greater certainty, the performance of the following work does not constitute work that is part of the certified trade:
1. Work performed by a person engaged in the repair or installation of single-phase hermetically sealed self- contained portable plug-in appliances with a maximum voltage of 240 volts and with factory produced systems pre-charged with refrigerant.
2
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
2.Work performed by a person engaged in the production of refrigeration and air conditioning systems. (5) Nothing in this section authorizes a person who holds a certificate of qualification or is otherwise authorized under
the Act to work in the certified trade to perform any function or carry out any activities for which a certificate is required under the Technical Standards and Safety Act, 2000.
Training programs
4. (1) An apprentice training program to become a refrigeration and air conditioning systems mechanic shall consist of five periods, each of which shall consist of 1800 hours of classes that provide training and instruction and of on the job work experience.
(2) An apprentice training program to become a residential air conditioning systems mechanic shall consist of three periods as follows:
1. Two periods, each of which shall consist of 1800 hours of classes that provide training and instruction and of on the job work experience.
2. One period of 900 hours of classes that provide training and instruction and of on the job work experience. (3) Despite subsection (1), in the case of a person who holds a certificate of qualification as a residential air
conditioning systems mechanic and who wishes to complete an apprentice training program to become a refrigeration and air conditioning systems mechanic, the apprentice training program shall consist of only three periods as follows:
1. One period of 900 hours of classes that provide training and instruction and of on the job work experience.
2. Two periods, each of which shall consist of 1800 hours of classes that provide training and instruction and of on the job work experience.
(4) An employer shall not establish an apprentice training program unless the program is approved by the Director.
Wages
5. (1) The rate of wages for an apprentice who is working in an apprentice training program to become a refrigeration and air conditioning systems mechanic shall be no less than the following percentage of the average rate of wages for journeypersons who have received such a certificate and are employed by the employer with whom the apprentice is working:
1. 40 per cent, during the first of the five periods of apprenticeship referred to in subsection 4 (1). 2. 50 per cent, during the second of the five periods of apprenticeship referred to in subsection 4 (1). 3. 60 per cent, during the third of the five periods of apprenticeship referred to in subsection 4 (1). 4. 70 per cent, during the fourth of the five periods of apprenticeship referred to in subsection 4 (1). 5. 80 per cent, during the fifth of the five periods of apprenticeship referred to in subsection 4 (1).
(2) The rate of wages for an apprentice who is working in an apprentice training program to become a residential air conditioning systems mechanic shall be no less than the following percentage of the average rate of wages for journeypersons who have received such a certificate and are employed by the employer with whom the apprentice is working:
1. 40 per cent, during the first of the two periods of apprenticeship referred to in paragraph 1 of subsection 4 (2). 2. 60 per cent, during the second of the two periods of apprenticeship referred to in paragraph 1 of subsection 4 (2). 3. 80 per cent, during the period of apprenticeship referred to in paragraph 2 of subsection 4 (2).
(3) Despite subsection (1), if a person holds a certificate of qualification as a residential air conditioning systems mechanic and begins an apprentice training program described in subsection 4 (3), the rate of wages for the person during his or her apprenticeship shall be no less than the following percentage of the average hourly rate of wages for journeypersons who have received such a certificate and are employed by the employer with whom the apprentice is working:
1. 60 per cent, during the period of apprenticeship referred to in paragraph 1 of subsection 4 (3). 2. 70 per cent, during the first of the two periods of apprenticeship referred to in paragraph 2 of subsection 4 (3). 3. 80 per cent, during the second of the two periods of apprenticeship referred to in paragraph 2 of subsection 4 (3).
3
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
(4) The minimum rate of wages established under subsections (1), (2) and (3) apply to all of the apprentice’s hours of work, whether for regular daily hours of work or for hours of work in excess of the regular daily hours of work.
Number of apprentices
6. (1) If an employer employs no more than seven journeypersons in the certified trade, the number of apprentices in the certified trade who may be employed by the employer shall not exceed the number set out in Column 2 of the Table to this subsection opposite the number of journeypersons employed by the employer and set out in Column 1 of the Table.
TABLE
Column 1 Column 2
Number of Journeypersons Number of Apprentices Allowed
1 1 2 1 3 2 4 2 5 3 6 3 7 4
(2) If an employer employs more than seven journeypersons in the certified trade, for every three journeypersons employed after the seventh journeyperson, the employer may employ an additional apprentice.
Transition
7. (1) A valid certificate of qualification in the certified trade issued before the day this Regulation comes into force shall be deemed on and after that day to be a certificate of qualification in the branch of the certified trade known as refrigeration and air conditioning systems mechanic.
(2) A valid certificate of apprenticeship in the certified trade issued before the day this Regulation comes into force shall be deemed on and after that day to be a certificate of apprenticeship in the branch of the certified trade known as refrigeration and air conditioning systems mechanic.
(3) If a contract of apprenticeship in the certified trade was filed with the Director under clause 9 (1) (b) of the Act before the day this Regulation comes into force and is not fully executed on or before that day,
(a) the contract shall be deemed on and after that day to be a contract of apprenticeship in the branch of the certified trade known as refrigeration and air conditioning systems mechanic; and
(b) every reference in the contract to the certified trade shall be deemed on and after that day to be a reference to the branch of the certified trade known as refrigeration and air conditioning systems mechanics.
(4) For the purpose of issuing a certificate of apprenticeship under section 16 of the Act on and after the day this Regulation comes into force, a person who completed an apprentice training program in the certified trade before that day shall be deemed to have completed an apprentice training program in the branch of the certified trade known as refrigeration and air conditioning systems mechanic.
Revocation
8. Regulation 1076 of the Revised Regulations of Ontario, 1990 is revoked.
Commencement
9. This Regulation comes into force on April 1, 2005.
4
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
COMPETENCY ANALYSIS PROFILE Refrigeration and Air Conditioning Systems Mechanic - Branch 1 – 313A
(All unshaded skill sets must be demonstrated/completed)
SKILL SETS SKILLS
PROTECT SELF AND OTHERS
Identify, interpret, and comply with safety directives
Wear, adjust, and maintain personal protective equipment
Practise good housekeeping in the workplace
Handle and dispose designated substances and refrigerants
Follow fire safety procedures
6238.0
6238.01
6238.02
6238.03
6238.04
6238.05
Operate emergency safety equipment
Follow first aid procedures
Report injuries Lock out equipment for repair or maintenance
Work within safe physical limits
6238.06
6238.07
6238.08
6238.09
6238.10
Operate material handling equipment
Operate worker elevating platforms
Handle and transport compressed gases and equipment
6238.11
6238.12
6238.13
5
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SETS SKILLS
PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION & AIR CONDITIONING (R&AC) SYSTEM
Read and interpret job documentation
Identify type of R&AC system
Identify and select R&AC system components and equipment
Identify design parameters of R&AC system
Calculate the R&AC system operating parameters
6239.0
6239.01
6239.02
6239.03
6239.04
6239.05 Identify and select
R&AC system operating controls
Identify and select R&AC system safety controls
Identify and select R&AC system functional controls
Identify and select R&AC system accessories
Identify and select welding, cutting, brazing, soldering, or purging equipment
6239.06
6239.07
6239.08
6239.09
6239.10
Identify and select hand tools
Identify and select power tools
Identify and select electrical measuring devices
Identify and select R&AC pressure, temperature, and flow measuring devices
Identify and select R&AC specialty instruments
6239.11
6239.12
6239.13
6239.14
6239.15
Identify and select R&AC precision measuring instruments
Identify and select the R&AC installation and material handling equipment
Identify and select material handling and worker elevating methods and equipment
Coordinate permits, inspections, and sub-trades
Complete planning work sheets
6239.16
6239.17
6239.18
6239.19
6239.20
Communicate with others
6239.21
6
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SETS SKILLS
NSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP)
Inspect AC and HP at site
Perform a site evaluation
Prepare work site Prepare site for installation
Assemble and install AC and HP components and accessories
6240.0
6240.01
6240.02
6240.03
6240.04
6240.05
Braze and solder AC and HP piping
Check AC and HP system for leaks
Evacuate and dehydrate system
Wire-in AC and HP
Charge AC and HP system with refrigerant
6240.06
6240.07
6240.08
6240.09
6240.10 Set and verify AC
and HP electrical, electronic, and automated control systems
Check and adjust air flow, water, and glycol levels
Verify charging of AC and HP system
Verify AC and HP system operating parameters
Commission AC and HP system
6240.11
6240.12
6240.13
6240.14
6240.15
Complete AC and HP installation and start-up documentation
6240.16
7
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SETS SKILLS
SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP)
Troubleshoot AC and HP accessories and components
Replace or repair AC and HP accessories and components
Replace or repair system zoning components
Repair or replace AC and HP operating and safety controls
Clean or replace AC and HP electrical components
6241.0
6241.01
6241.02
6241.03
6241.04
6241.05
Test or replace AC and HP electronic components
Rewire and repair AC and HP system wiring
Clean or replace actuator and damper/zone controls
Repair or replace refrigerant flow and metering devices
Clean and replace heat transfer devices, coils, and heat exchangers
6241.06
6241.07
6241.08
6241.09
6241.10
Adjust and replace heat transfer medium
Test or replace AC and HP electrical heaters, HRV/ERV and electronic air cleaners
Replace or repair system piping
Replace or repair AC and HP condensate drains and accessory components
Check system for leakage
6241.11
6241.12
6241.13
6241.14
6241.15
Replace air cooling compressor
Clean or replace AC and HP filter system and components
Replace or repair the air side of AC and HP equipment
Replace or repair air handler components
Replace or repair AC and HP fans and motors
6241.16
6241.17
6241.18
6241.19
6241.20
Check operations and functions of total AC and HP system
Complete AC and HP service and maintenance records
Clean up work site
6241.21
6241.22
6241.23
8
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SETS SKILLS
INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
Read and interpret R&AC installation and start up documentation
Inspect R&AC system, accessories, and components at work site
Perform a work site evaluation
Prepare work site Coordinate permits, inspections, and sub-trades
6242.0
6242.01
6242.02
6242.03
6242.04
6242.05 Prepare site for
installation Assemble and install R&AC system, accessories, and components
Assemble R&AC piping and components
Join and install R&AC piping
Check refrigerant piping for leaks
6242.06
6242.07
6242.08
6242.09
6242.10
Check component piping for leaks
Assemble and install R&AC electrical system accessories and components
Evacuate and dehydrate R&AC system
Commission R&AC system
Complete the installation and commissioning records
6242.11
6242.12
6242.13
6242.14
6242.15
Clean up work site
6242.16
MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
Troubleshoot R&AC systems and components
Clean and maintain R&AC filters and components
Clean and maintain R&AC condenser, evaporator, and accessory components
Clean and maintain R&AC humidifier and components
Clean or replace R&AC electrical components
6243.0 6243.01 6243.02 6243.03 6243.04 6243.05
Check operation and functions of total R&AC system
Clean up work site
Complete R&AC maintenance documentation
6243.06
6243.07
6243.08
9
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SETS SKILLS
SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
Check R&AC system accessories and components
Replace or repair R&AC mechanical components
Repair or replace R&AC condensate components
Repair or replace R&AC piping, accessories, and components
Repair or replace R&AC refrigerant system, components, and accessories
6244.0
6244.01
6244.02
6244.03
6244.04
6244.05
Repair or replace R&AC open, semi- hermetic, or hermetic compressor
Repair or replace R&AC fans and components
Repair or replace R&AC pneumatics
Replace R&AC controls and switches
Repair or replace Variable Air Volume (VAV) components
6244.06
6244.07
6244.08
6244.09
6244.10
Repair or replace R&AC metering devices
Replace or repair R&AC electrical and electronic system and components
Decommission packaged R&AC equipment
Decommission split-system R&AC equipment
Decommission R&AC equipment for demolition
6244.11
6244.12
6244.13
6244.14
6244.15
Clean up work site Complete servicing documentation
6244.16
6244.17
PERFORM CUSTOMER SERVICE
Determine nature of service or maintenance call
Conduct a site evaluation
Perform a diagnostic inspection
Estimate costs of service or maintenance call
Complete service or maintenance schedule
6245.0
6245.01
6245.02
6245.03
6245.04
6245.05 Complete job work
order Instruct clients
6245.06
6245.07
10
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
PREFACE
This training standard was developed by the Workplace Training Branch of the Ministry of Training, Colleges, and Universities (MTCU), in partnership with the Provincial Advisory Committees and in consultation with representatives from the industry. This document is intended to be used by apprentice, supervisor/trainer and sponsor/employer as a "blueprint" for training and as a prerequisite for completion and certification.
This training document becomes the apprentice’s only record of workplace training performance.
The supervisor/trainer and apprentice are required to sign off and date the skills following each successful acquisition, unless a skill is marked shaded (optional).
The care and maintenance of this training document are the joint responsibility of the apprentice and the sponsor/employer. By signing off the skill, the supervisor/trainer and the apprentice are indicating that the apprentice has demonstrated competence of the skill. This training standard has been developed specifically for documenting the apprentices acquisition of skills of the trade.
11
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
DEFINITIONS
ACA Apprenticeship and Certification Act, 1998
Certificate of Apprenticeship (C of A) Certification issued to individuals who have demonstrated that they have completed an apprenticeship in Ontario.
Certificate of Qualification (C of Q) Certification issued to C of Q applicants who have achieved a passing grade on the certification exam for their trade.
Competency Analysis Profile A document that identifies the training needs of an individual trade and details the skills/skill sets that must be demonstrated.
Competence The ability of an individual to perform a skill repeatedly and without assistance in the workplace to the standard set out in the Training Standard or Schedule of Training.
Including When used before a list of actions or items, the list is not exhaustive but contains major examples of the actions or items intended.
General Performance Objective (On-the-Job Skill Set) Describes a set of skills, which include all performance objectives under that skill set.
Industry Committee (IC) - under the ACA and Provincial Advisory Committee (PAC) under the TQAA Under the ACA and TQAA, the Minister may appoint a provincial committee in any trade or group of trades to advise the Minister in matters relating to the establishment and operation of apprenticeship training programs and trades qualifications.
Journeyperson or Equivalent A person who has acquired the knowledge and skills in a trade, occupation or craft as attested to by a provincial or territorial authority.
Mandatory Status assigned to unshaded individual skills, skill sets or general performance objective, which must be signed off to demonstrate that the apprentice has completed their program.
12
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Optional Status assigned to shaded individual skills, skills sets or general performance objective for which sign-off is not required for the apprentice to complete the program.
Sign-off Signature of the sponsor/employer of record or an individual, to whom that sponsor or employer has delegated signing authority, indicating an apprentice’s achievement of competence.
Skill Individual skill described in the Training Standard (note: does not mean the larger skill groups referred to in the Training Standard as Skill Sets, Training Units, or General Performance Objective, but the individual skills that make up those groups).
Skill Sets Group of individual skills found in the Training Standard (may also be called Training Unit or General Performance Objective)
Skill Set Completion Form Lists all skill sets and includes space for sign-off by sponsor/employer of record.
Sponsor/Employer Means a person that has entered into a registered training agreement under which the person is required to ensure that an individual is provided with workplace-based training in a trade, other occupation, or skill set as part of an apprenticeship program approved by the Director.
Sponsor/Employer of Record Refers to the sponsor or employer documented as the signatory to the current training agreement or contract. In order for a sponsor/employer to be considered for the training of apprentices, they must identify that the workplace has qualified journeypersons or equivalent on site and can identify that the workplace has the tools, equipment, materials, and processes which have been identified by Provincial Advisory Committees (PACs) or Industry Committees (ICs) to be required for the trade.
Supervisor An individual who oversees the execution of a task or oversees the actions and work of others.
13
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Trainer A qualified trainer in a compulsory trade is a journeyperson with a Certificate of Qualification or in a voluntary trade is an individual who is considered equivalent to a journeyperson with a Certificate of Qualification.
TQAA Trades Qualification and Apprenticeship Act.
Training Standard A document that has been written in concise statements, which describe how well an apprentice must perform each skill in order to become competent. By using the document, trainers will be able to ensure that the apprentice is developing skills detailed for the occupation.
14
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
IMPORTANT DIRECTIONS
Apprentice
1. All complete skills or skill sets must be signed and dated by both the apprentice and sponsor/employer when either all terms of the contract have been completed or the apprentice leaves the employ of the employer.
2. It is the responsibility of the apprentice to inform the local Apprenticeship Client
Services Office regarding the following changes:
• change of sponsor/employer address; • change of apprentice name or address; • transfer to a new sponsor/employer.
3. The Skill Set Completion Form must be completed and signed by the current
sponsor/employer and presented to the local Apprenticeship Client Services Office at the fulfillment of all terms of a Contract of Apprenticeship/Training Agreement.
4. The Apprentice Completion Form with the Completed and Authorized Training Standard
must be presented to the local Apprenticeship Client Services Unit.
Sponsors/Employers and Supervisors/Trainers
The Training Standard identifies skills required for this trade/occupation and its related training program.
This Training Standard has been written in concise statements, which describe how an apprentice must perform each skill in order to become competent. Competence means being able to perform the task to the required standard.
By using this Training Standard, supervisors/trainers will be able to ensure that the apprentice is developing the skills detailed for the trade/occupation.
Supervisors/trainers and apprentices are required to sign off and date the skills following each successful acquisition.
Sponsors/employers participating in this training program will be designated as the Signing Authority and are required to attest to successful achievement by signing the appropriate box included at the end of each skill set.
15
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
NOTICE OF COLLECTION OF PERSONAL INFORMATION
1. At any time during your apprenticeship training, you may be required to show this training standard to the Ministry of Training, Colleges and Universities (the Ministry). You will be required to disclose the signed Apprenticeship Completion form to the Ministry in order to complete your program. The Ministry will use your personal information to administer and finance Ontario’s apprenticeship training system, including confirming your completion and issuing your certificate of apprenticeship.
2. The Ministry will disclose information about your program completion and your certificate of apprenticeship to the Ontario College of Trades, as it is necessary for the College to carry out its responsibilities.
3. Your personal information is collected, used and disclosed by the Ministry under the authority of the Ontario College of Trades and Apprenticeship Act, 2009.
4. Questions about the collection, use and disclosure of your personal information by the Ministry may be addressed to the:
Manager, Employment Ontario Contact Centre Ministry of Training, Colleges and Universities 33 Bloor St. E, 2nd floor, Toronto, Ontario M7A 2S3 Toll-free: 1-800-387-5656; Toronto: 416-326-5656 TTY: 1-866-533-6339 or 416-325-4084.
16
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
ROLES & RESPONSIBILITIES OF APPRENTICE, SPONSOR/EMPLOYER AND SUPERVISOR/TRAINER
Apprentice “Apprenticeship is Learning On-the-job”
• Practice safe work habits.• Use your apprenticeship training standard as a journal to keep track of which skills you have
achieved.• Talk over your training plan with your Training Consultant, Employer, Union, or Sponsor.• Know what tools are required for your trade and how to use them.• Ask questions and keep asking.• Talk to your employer about your training needs.• Demonstrate enthusiasm and good work habits.• Ensure that you and your supervisor/trainer sign off skill/skill sets upon demonstration of
competency.
Sponsor/Employer “Training is an Investment”
• Demonstrate safe work habits.• Attest to successful achievement by signing the skill/skills sets.• Provide opportunities and time for the apprentice to learn the trade.• Offer practical trade training experiences that cover all of the skill sets.• Foster work ethics that support training while minimizing productivity losses.• Set out clear expectations, then recognize or reward performance excellence.• Involve both the apprentice and supervisor/trainer in developing the training plan.• Use the Training Standard as a monitoring tool and part of regular performance evaluations.• Select supervisors/trainers with good communication skills and who work well with others.• Encourage supervisors/trainers to take upgrading courses - (e.g. Train the Trainer, Mentor
Coach, etc).• Complete the Skill Set Completion Form once the apprentice has demonstrated competency
in the training.• Ensure that the apprentice always works under the direction of or has access to a qualified
supervisor/trainer.• Vary the apprentice’s exposure to all the skills set out in the training standard.
17
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Supervisor/Trainer • Demonstrate safe work habits. • Treat apprentices fairly and with respect. • Use the Training Standard as a guide to evaluating competence in each skill area. In using
the Training Standard, supervisors/trainers will be able to ensure that the apprentice is developing skills detailed for the trade/occupation.
• Review the Training Standard with the apprentice and develop a training plan. • Respond fully to all questions. • Be patient. Explain what is to be done then, show how it is done, and then let the apprentice
demonstrate the task. • Provide continuous feedback. • Sign off individual skills/skill sets once the apprentice demonstrates competence in the skill. Suggestions for Assessing the Progress of the Apprentice in the Workplace • Use informal daily observation. • Provide constructive feedback to build confidence. • Allow the supervisor/trainer time to teach and demonstrate the skills. • Take prompt action wherever problems occur. • Conduct regular performance reviews involving the apprentice, supervisor/trainer and
sponsor/employer. • Use the Training Standard as the reference for establishing the competency of the apprentice.
18
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
SKILL SET COMPLETION FORM
SKILLS SETS
TITLE
SIGNING AUTHORITY
6238.00
PROTECT SELF AND OTHERS
6239.00
PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
6240.00
INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP)
6241.00
SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP)
6242.00
INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
6243.00
MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
6244.00
SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
6245.00
PERFORM CUSTOMER SERVICE
NOTE ON SHADED PERFORMANCE OBJECTIVES AND SKILLS: • Shaded performance objectives and skill sets are optional. The shaded skills do not have to be
demonstrated or signed-off for completion of the on-the-job component of the apprenticeship • The in-school curriculum learning outcomes will cover all of the skill sets, both shaded and unshaded. • The Certificate of Qualification examination will test the whole of the trade and may test both shaded
and unshaded performance skill sets.
19
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6238.00 PROTECT SELF AND OTHERS
GENERAL PERFORMANCE OBJECTIVE
Protect self and others by: identifying, interpreting, and complying with safety directives; wearing, adjusting, and maintaining personal protective equipment; practising good housekeeping in the workplace; handling and disposing of designated substances and refrigerants; following fire safety and first aid procedures; reporting injuries; locking out equipment for repair or maintenance; working within safe physical limits; operating material handling equipment, elevating worker platforms, and emergency safety equipment; and, handling and transporting compressed gases and equipment.
PERFORMANCE OBJECTIVES
SKILLS
6238.01 Identify, interpret, and comply with safety directives provided in applicable Acts, Regulations, Legislation, and Codes including (not limited to) the Occupational Health and Safety Act (OHSA), Worker’s Compensation Act (WCA), Ministry of Environment (MOE) Regulations, Dangerous Goods Transportation Act (DGTA), Workplace Hazardous Materials Information System (WHMIS), Ontario Fire Code (OFC), Canadian Electrical Code (CEC), Mechanical Refrigeration Code (B52), Energy Act (EA), and TSSA Act and Regulations.
Date Completed Apprentice Supervisor/Trainer
6238.02 Wear, adjust, and maintain personal protective equipment including (not limited to) safety and rubber boots, hard hats, gloves, glasses, goggles, masks, face shields, coveralls, fall-arrest equipment, and ear protectors, to ensure the correct fit and optimum protection for the wearer and the task being performed, in compliance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
20
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6238.00 PROTECT SELF AND OTHERS ...cont'd
6238.03 Practise good housekeeping in the workplace by cleaning up spills and leaks, keeping work area clean and clear of obstructions, and storing tools or equipment, so that the potential for accident or injury is prevented and tools or equipment are in place and available, in compliance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6238.04 Handle and dispose designated substances and refrigerants using specified handling and storage equipment and disposing of recovered refrigerant, so that the operator is protected from injury, the environment from contamination, and procedures are followed in compliance with applicable Acts, Regulations, Legislation, and Codes, manufacturer’s specifications, and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6238.05 Follow fire safety procedures including (not limited to): locating and assessing the severity of the fire; handling fire extinguishing equipment; suppressing minor fires; activating alarms; and, reporting incidents; in accordance with applicable Acts, Regulations, Legislation, and Codes, manufacturer’s specifications, and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
21
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6238.00 PROTECT SELF AND OTHERS ...cont’d
6238.06 Operate emergency safety equipment including (not limited to) fire equipment, respirators, and fall-arrest equipment, ensuring that procedures are carried out in a safe and efficient manner in accordance with company standards/policies, manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6238.07 Follow first aid procedures to treat conditions including (not limited to) sudden illness or minor injuries, burns, cuts, abrasions, falls, sprains, chemical inhalations, and contaminants in eyes, by using first aid equipment and following procedures so that the victim is stabilized and prepared for further first aid treatment in accordance with applicable Acts, Codes, Legislation, Regulations, and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6238.08 Report injuries to supervisor or first aid personnel promptly and clearly, ensuring that the injured person is attended to, and information is reported precisely and accurately describing how incident occurred, so that future recurrence of similar accidents is prevented, and reporting complies with company standards/policies, applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
22
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6238.00 PROTECT SELF AND OTHERS ...cont’d
6238.09 Lock out equipment for repair or maintenance by following company procedures including (not limited to): shutting down system; de-energizing equipment; tagging equipment; and, ensuring that power source is off and locked out prior to commencing maintenance or service; so that no damage or injury is caused to the operator or equipment, in compliance with applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6238.10 Work within safe physical limits by applying lifting procedures for bending, lifting, transporting, or climbing with heavy loads, so that personal injury is prevented in accordance with applicable Acts, Regulations, Legislation and Codes and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6238.11 Operate material handling equipment including (not limited to) hoists, cranes, slings, cables, and chains, so that the materials, parts, and equipment are removed, transported, and stored in compliance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6238.12 Operate worker elevating platforms including (not limited to) ladders, boom truck, buckets, scaffolding, scissor lift, or articulating man lift, ensuring that the correct lifting procedures and equipment are used to move and hoist individuals, in compliance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
23
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6238.00 PROTECT SELF AND OTHERS ...cont’d
6238.13 Handle and transport compressed gases and equipment including (not limited to) manifolds, tubing, gases, and hoses, so that all compressed gases are handled, moved, and stored in accordance with applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
24
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
GENERAL PERFORMANCE OBJECTIVE
Plan and prepare for installation, maintenance, or service of refrigeration and air conditioning (R&AC) system by: reading and interpreting job documentation; identifying type and components of R∾ identifying design parameters; calculating system operating parameters; identifying and selecting operating controls, safety controls, functional controls, system accessories, cutting, brazing, soldering, or purging equipment, hand tools, powers tools, electrical measuring devices, pressure, temperature and flow measuring devices, speciality instruments, precision measuring instruments, materials and material handling equipment, and worker elevating platforms; coordinating permits, inspections, and sub-trades; completing planning records; and communicating with others.
PERFORMANCE OBJECTIVES
SKILLS
6239.01 Read and interpret job documentation including (not limited to) work order, manufacturer’s specifications, architectural and mechanical engineering drawings, wiring diagrams, manufacturer’s installation, operation, and maintenance specifications (IOM), and applicable Acts, Regulations, Legislation, and Codes to identify: type and size of equipment; type and components of system; design and operating parameters of system; required permits and licenses; installation, servicing, or maintenance procedures; location of mechanical causeways; material handling equipment; required tools, equipment, and materials; and any other information need to plan the completion of the installation, servicing, or maintenance job.
Date Completed Apprentice Supervisor/Trainer
25
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.02 Identify type of R&AC system by reading and interpreting job specifications
including (not limited to) work orders, manufacturer’s specifications, and architectural and mechanical engineering drawings, to identify any type of Conditioning or refrigeration system including (not limited to) Roof Mounted HVAC System, Chiller System, Split System, Packaging System, Built-Up System, Heat Recovery Ventilation/Energy Recovery Ventilator (HRV/ERV), Filtration System, Refrigeration or Conditioning System, and Controlled Environment System, so that the correct installation, servicing, or maintenance parameters and procedures can be determined in accordance with company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.03 Identify and select R&AC system components and equipment including (not limited to) heat recovery ventilator (HRV), controls, dampers, condensing unit, heat pump, energy recovery ventilator (ERV), condensate pumps, air or water cooled condensing unit or cooling tower unit, dry coolers, evaporators or chillers, air handlers, heat and energy recovery evaporator, fans, humidifier/dehumidifier, filtration system, condensate, brine, refrigerant, and pumps, ensuring that the components and equipment selected are the correct ones for the application in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
26
Ontario College of Trades ©
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.04 Identify design parameters of R&AC system by reading and interpreting job
documentation including (not limited to) work orders, manufacturer’s specifications, architectural and mechanical engineering drawings, wiring diagrams, building codes, government codes and legislation, Safety Legislation, American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) codes, MRC - B52, and Manufacturer’s Installation, Operation and Maintenance specifications (IOM) to identify: type, size, capacity, and parameters of the equipment; system components and parts; required permits; installation or service procedures; required tools, equipment and materials; location and layout of system; required sub-trades; and any other information needed to plan the installation of the R&AC system.
Date Completed Apprentice Supervisor/Trainer
6239.05 Calculate R&AC system operating parameters to determine and set out design features including (not limited to): heat loss or gain; ventilation loads; electrical loads; humidification and dehumidification loads; filtration/purification capacity; suspension loads; required equipment and accessories; air flow rates; liquid flow rates; pipe quantity, size, and fittings; drain system and parameters; refrigeration parameters by reading and interpreting industry standards, charts, psychrometric charts, tables, and manuals; and, using tape measures, calculators, scaled rules, and software; in order to determine that the R&AC system is the correct type and size for the application, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
27
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Date Completed Apprentice Supervisor/Trainer
28
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.06 Identify and select R&AC system operating controls including (not limited to)
defrost, pressures, on/off switch, humidity, and temperature controls, ensuring that the operating controls and devices selected are the correct ones to measure the operational parameters of the system and that all controls are clean, calibrated, operational, and functioning, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.07 Identify and select R&AC system safety controls including (not limited to) electrical, temperature, pressure, failure switches, relief valves, oil failure controls, and loads or overloads, ensuring that the safety controls selected are the correct ones for the safety parameters of the system and that controls are clean, calibrated, operational, and functioning, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.08 Identify and select R&AC system functional controls including (not limited to) flow rates, levels, multi-staging, capacity control, metering, temperatures, and pressures, ensuring that the controls selected are the correct ones for the parameters of the system and that all functioning controls are clean, calibrated, operational, and functioning, in accordance with design parameters, manufacturer’s specifications, codes, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Date Completed Apprentice Supervisor/Trainer
29
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.09 Identify and select R&AC system accessories including (not limited to) filter
driers, oil separators, liquid moisture indicators, accumulators, vibration absorbers and indicator lights, ensuring that accessories selected are the correct ones for the R&AC system, in compliance with work order, design parameters,
manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.10 Identify and select brazing, soldering, welding, cutting, or purging equipment including (not limited to) compressed gases, manifold, gauges/hoses, torches, welding, brazing or soldering materials, flux, abrasives, and leak testing equipment, ensuring that the equipment selected are the correct ones for the application and that all equipment is cleaned, maintained and ready for use, in accordance with work order, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.11 Identify and select hand tools including (not limited to) spanners, reamers, dies, pop-rivet guns, manifolds, levels, layout tools, screw drivers, pliers, wrenches, metal snips, brazing/cutting torches, swaging/flaring tools, hammer, tubing cutters, pipe cutters, reamers, sockets, ratchets, saws, chisels, and specialty tools, ensuring that the hand tools selected are the correct ones for the application and that the tools are ready for use to install, service, or maintain the R&AC system, in accordance with work order, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.12 Identify and select power tools including (not limited to) drills, saws, pipe
threaders, vacuum pumps, recovery units, pressure washers, and power-actuated tools, ensuring that the power tools selected are the correct ones for the application and ready for use to install, service, or maintain the system, in accordance with work order, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.13 Identify and select electrical measuring devices including (not limited to) ammeters, voltmeters, ohmmeters, multimeters, recorders, phase detectors, megometers, watt meters, and specialty instruments, ensuring that the electrical measuring devices selected are the correct ones for the application and are cleaned, maintained, calibrated and ready for use, in accordance with work order, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.14 Identify and select the R&AC pressure, temperature, and flow measuring devices including (not limited to) manifold gauges, manometers, thermometers, anemometers, hydrometers, hygrometers, velometers, psychrometers, thermo- couples, and tachometers, ensuring that the devices are the correct ones to measure the operating parameters of the system and that the devices are cleaned, calibrated, operational, and functioning, in accordance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
30
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.15 Identify and select R&AC speciality instruments including (not limited to)
micron gauges, refrigerant gauges, tachometers, scales, and infrared instruments, ensuring that the instruments are the correct ones to determine conditions and quantities of system and that the instruments are cleaned, calibrated, operational, and functioning, in accordance with manufacturer’s specifications, work orders, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.16 Identify and select R&AC precision measuring instruments including (not limited to) micron gauges, refrigerant gauges, tachometers, scales, infrared instruments, and speciality measuring instruments, ensuring that the instruments are the correct ones to determine conditions and parameters of the system and that the instruments are cleaned, calibrated, operational, and functioning, in accordance with manufacturer’s specifications and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6239.17 Identify and select the R&AC installation and material handling equipment including (not limited to): piping; insulation; brazing, soldering, welding, and cutting material; wiring material; electrical components; vibration absorbers; suspension equipment and materials; levelling equipment; fasteners; drain tubing; solvents; nitrogen and refrigerant; material handling and installation tools or equipment; and, chaseway materials and equipment; ensuring that equipment selected are the correct ones to install the system and that materials are available and ready for use, in accordance with work order, design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
31
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.18 Identify and select material handling and worker elevating methods and
equipment including (not limited to) ladders, boom truck, buckets, scaffolding, scissor lift, articulating man lift, hoists, cranes, slings, cables, and chains, ensuring that equipment selected are the correct ones to lift and move equipment and personnel, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.19 Coordinate permits, inspections, and sub-trades to ensure that all permits and inspections have been arranged prior to installation and sub-trades have been contacted and scheduled, in compliance with industry and company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6239.20 Complete planning work sheets by ensuring that work order, permits, sign-off sheets, or manufacturer’s check lists are available and ready for use, to ensure that all aspects of the R&AC installation, servicing, or maintenance can be identified, recorded, and scheduled, in accordance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
32
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6239.00 PLAN AND PREPARE FOR INSTALLATION, MAINTENANCE, OR SERVICE OF REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6239.21 Communicate with others to identify previous job operations, availability of
tools, parts, and equipment, scheduling requirements, permits or inspections, and any other information needed to plan the installation or service, ensuring that all information communicated is clear, concise, and accurate.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
33
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP)
GENERAL PERFORMANCE OBJECTIVE
Install and start up air cooling (AC) and heat pump (HP) by: inspecting system at site; performing site evaluation; preparing work site; preparing site for installation; assembling and installing system components, and accessories; brazing and soldering piping; checking for leaks; evacuating or dehydrating system; wiring-in system; charging system with refrigerant; setting and verifying electrical, electronic, and automated control systems; checking and adjusting air flow, water, and glycol levels; verifying charging and operating parameters of system; commissioning system; completing installation and start-up documentation.
PERFORMANCE OBJECTIVES
SKILLS
6240.01 Inspect AC and HP at site by following required procedures including (not limited to) removing packaging, inspecting unit for damage, and, checking equipment design parameters, to ensure that the AC and HP conforms to the work order and manufacturer’s specifications.
Date Completed Apprentice Supervisor/Trainer
34
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.02 Perform a site evaluation by following required procedures including (not
limited to): visually inspecting site for obstructions; measuring equipment parameters; placing equipment to layout; evaluating effectiveness and reliability of installation site design; checking that required utilities are installed and available; determining mechanical chase ways; and, discussing with client the scope of the installation; so that the installation plan is verified and coincides with the scope of work and design parameters, in accordance with client requirements, work order, industry standards, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.03 Prepare work site by following required procedures including (not limited to): setting up and arranging installation tools and equipment; checking that power or gas source is available; recovering refrigerant; removing and disposing of existing equipment including air handling equipment, heat pump, evaporator coils, condensing unit, or refrigerant piping; removing obstacles and debris from work area; placing equipment to layout design; preparing mechanical chaseways; and, using drop sheets, hand and power tools or material handling equipment; so that the work site is prepared and ready for the installation of the AC and HP system, in accordance with work orders, company standards/policies, client requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
35
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.04 Prepare site for installation by following required procedures including (not
limited to): visually checking site; checking job site conditions against the layout documentation; locating equipment; and, placing equipment on required mounts or supports including slabs, curbs, brackets, sleepers, pads, and hangers; so that the mounts or supports are located, positioned, and aligned, in accordance with installation plan, work order, customer requirements, industry standards, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.05 Assemble and install AC and HP components and accessories by following required procedures including (not limited to): assembling air handler and filtering equipment, condensing unit, evaporator coil, heat pump, refrigerant, refrigerant accessories, piping, insulation, controls, drain line, condensate pump, indoor air quality equipment, humidifiers/dehumidifiers, system accessories, Heat Recovery Ventilator (HRV), Energy Recovery Ventilator (ERV), mechanical chase ways, and mechanical ventilation; tying in condensate line to open drain; cutting pathway for piping, wiring, and duct work; measuring and checking installation; lifting and moving using material handling equipment; placing equipment against the layout design; and, using required hand and power tools; ensuring that system is installed in accordance with work order, industry and company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
36
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.06 Braze and solder AC and HP piping by following required procedures
including (not limited to): setting up oxygen, acetylene, propane, nitrogen, soldering devices, hoses, regulators, torch accessories and fire extinguishers; inspecting and cleaning piping; purging nitrogen; brazing and soldering piping using flux, filler rods, brazing alloy, and solder; preparing piping chase ways; forming piping joints; and, cleaning, storing, and adjusting brazing or soldering equipment; so that leak-proof joints are formed and piping is installed, in accordance with work orders, industry and company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.07 Check AC and HP system for leaks by following required procedures including (not limited to): visually inspecting; performing various leak tests; pressurizing the system; and, using nitrogen, gauges, soap solutions, electronic leak detectors, or dry air; in order to verify that there are no leaks and that the system integrity conforms with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.08 Evacuate and dehydrate system by following required procedures including (not limited to): releasing nitrogen from system; evacuating system; and, using hand tools, manifold gauges, vacuum pumps, micron gauges, or thermistors; so that all moisture and non-condensables are removed from system and equipment is cleaned and ready for use, in compliance with work order, design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
37
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.09 Wire-in AC and HP by following required procedures including (not limited to):
reading and interpreting electrical diagrams, schematics, and IOM specifications; preparing wiring chaseway; using hand or power tools, measuring instruments or electrical measuring instruments; and, visually inspecting wiring; so that the system wiring is correctly installed in accordance with work order, design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.10 Charge AC and HP system with refrigerant by following required procedures including (not limited to): reading and interpreting rating and IOM specifications; using hand tools, manifold gauges, hoses, weigh scales, and charging cylinders; and, putting refrigerant into system following correct charging procedures; ensuring that the system is charged in accordance with manufacturer’s specifications, IOM specifications, design parameters, applicable Acts, Regulations, Legislation, and Codes, and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
38
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.11 Set and verify AC and HP electrical, electronic, and automated control
systems by following required procedures including (not limited to): turning power on; checking primary and secondary voltage delivery, motor rotation, and oil levels; setting controls; adjusting hi/low pressure controls; testing defrost controls on heat pumps; checking crankcase heaters, fan cycling accessories, off cycle timers, electronic or manual thermostat operations, zone control functions, and air quality accessory controls; and, using hand tools, specialty tools, gauges, temperature measuring instruments, electrical measuring instruments, simulators, and analyzers; so that all control parameters are set to preset operational parameters, in accordance with manufacturer’s specifications, IOM specifications, design parameters, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.12 Check and adjust air flow, water, and glycol levels using hand tools, flow meters, gauges, and hydrometers to ensure that the system is operational and functioning at the specified parameters, in accordance with manufacturer’s specifications, IOM specifications, codes, design parameters, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.13 Verify charging of AC and HP system by following required procedures including (not limited to): reading and interpreting superheat and sub-cooling charts; checking refrigerant charge and oil levels; making necessary adjustments; using hand tools, manifold gauges, thermometers, psychometer, weigh scales, and reclaimers; and, documenting adjustments to refrigerants; so that the pressures, temperatures, flows, and levels are operating at the specified parameters, in accordance with manufacturer’s specifications, IOM specifications, design parameters, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
39
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.14 Verify AC and HP system operating parameters including pressures,
temperatures, flow rate, voltages, amperage, fluid levels, and speeds by checking using hand tools, pressure gauges, temperature measuring instruments, flow measuring instruments, electrical measuring instruments, level indicators, simulators, and tachometers, and by documenting results, so that the operating parameters are documented in accordance with design parameters, manufacturer’s specifications, job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6240.15 Commission AC and HP system by following required procedures including (not limited to): verifying that all sub-trade work has been inspected and certified; verifying that all gas operations have been checked and certified; turning on power and starting up system; setting limit, operating, and safety controls; testing system parameters including pressures, temperatures, flow rate, voltage, amperage, fluid levels, and speeds; making required adjustments; and, using hand or power tools, pressure gauges, temperature measuring instruments, flow measuring instruments, electrical measuring devices, or tachometers; so that the total system is verified to be operational and functioning in accordance with design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
40
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6240.00 INSTALL AND START UP AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6240.16 Complete AC and HP installation and start-up documentation by recording
operational parameters on manufacturer’s or company check lists and completing warranty forms, ensuring that installation data is completed in a clear, concise, and legible manner, in accordance with job specifications and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
41
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP)
GENERAL PERFORMANCE OBJECTIVE
Service or maintain AC and HP system by: troubleshooting, replacing, or repair system accessories and components; replacing or repairing zoning components, operating and safety controls, refrigerant flow and metering devices, piping, condensate drains, air side of equipment, air handler, fans, and motors; cleaning or replacing electrical components, actuator and damper/zone controls, heat transfer devices, coils, and heat exchangers, and filter system; testing or replacing electronic components, electrical heater, HRV/ERV, and electronic air cleaners; rewiring and repair wiring; adjusting and replacing heat transfer medium; replacing air cooling compressor; checking for leakage; checking operations and functions of total system; completing service and maintenance records; and cleaning up work site.
PERFORMANCE OBJECTIVES
SKILLS
6241.01 Troubleshoot AC and HP accessories and components by following required procedures including (not limited to): discussing with client to determine nature of service call; performing an inspection and diagnostic check; checking mechanical and electrical system; reading and interpreting IOM charts; determining corrective actions or options; estimating cost of service; writing up a work sheet; and, using metres, gauges, hand or power tools, and price lists; so that the scope of the work is determined and documented in accordance with company standards/policies, client requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
42
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.02 Replace or repair AC and HP accessories and components by following
required procedures including (not limited to): visually inspecting liquid/moisture indicators, accumulators, HRV/ERV, humidifier, pressure controls and other direct related components; replacing or repairing defective components and accessories; adjusting controls; and, documenting results; so that the system accessories are operational and functioning to design parameters in accordance with work orders and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.03 Replace or repair system zoning components by following required procedures including (not limited to): discussing with client to determine the nature of problem; inspecting bearings, linkages, dampers, actuators and wiring; lubricating moving parts; replacing or repairing defective components; adjusting controls; using required hand tools, PCs, software, and lubricants; and, documenting results; so that the zoning components are operational and functioning in accordance with work orders, client requirements, design parameters, manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
43
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.04 Repair or replace AC and HP operating and safety controls by following
required procedures including (not limited to): checking and testing temperature, pressure, humidity, voltage, and amperage; visually checking for damaged or defective controls; checking integrity of controls and wiring; repairing or replacing defective components; simulating conditions to check functions of controls; using thermometers, pressure gauges, hygrometers, psychrometers, multimeters, ammeters, voltmeters, ohmmeters, and manometers; and, documenting results; so that all controls are verified to be operational and functioning, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.05 Clean or replace AC and HP electrical components by following required procedures including (not limited to): checking for oil leakage, defects, and discolouration; testing operation of components; cleaning components; replacing defective components such as capacitors, transformers, relays, terminal blocks, fuse blocks, contactors, coils, circuit breakers, thermal overloads, fuses, fuseable links, connectors, wiring, or switches; using hand tools, electrical measuring instruments, specialty tools, and cleaning solvents; and, documenting results; so that the electrical system integrity is restored to meet design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
44
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.06 Test or replace AC and HP electronic components by following required
procedures including (not limited to): inspecting for defects, discolouration, odour, corrosion, and moisture; checking operation and functions of components; performing an operational test; verifying grounding components; checking operational sequences and set up; replacing batteries in thermostat; modifying program; using hand or power tools, multimeters, simulators, and battery testers; and, documenting results; so that the electronic components are functioning to restore equipment integrity to meet design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.07 Rewire and repair AC and HP system wiring by following required procedures including (not limited to): inspecting for defects, discolouration, odours, and defective supports; re-wiring systems; inspecting and tightening all connections; checking for required wire size and wire supports; checking wiring chaseways; checking integrity of the exterior or interior system wiring; using hand or power tools, wire gauge, and electrical measuring equipment; and, documenting results; so that the wiring integrity is restored to meet design parameters, company standards/policies, manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
45
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.08 Clean or replace actuator and damper/zone controls by following required
procedures including (not limited to): checking and replacing electric and electronic actuators; checking and replacing solid state devices or transducers; cleaning and lubricating damper bearings; checking and replacing defective controls; checking and replacing dampers; using hand tool or power tools, solvents, lubricants, multimeters, simulators, and speciality tools; and, documenting results; so that the controls are operating to restore the equipment integrity to meet design parameters, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.09 Repair or replace AC and HP refrigerant flow and metering devices by following required procedures including (not limited to): visually inspecting external piping and insulation; checking all operating components, piping integrity, supports, liquid moisture indicator, filter driers, hermetic compressor, and metering devices; replacing driers, capacity controls, pressure regulators, and compressors; repairing defective piping, insulation, and supports; recharging system; using multimeters, pressure/temperature gauges, hand or power tools, recovery equipment, charging cylinder, electronic scales and brazing or soldering equipment; and, documenting results; so that the devices are restored and the system performance conforms to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
46
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.10 Clean and replace heat transfer devices, coils, and heat exchangers by
following required procedures including (not limited to): determining gas technician licence requirements; coordinating sub-trades if required; inspecting heat transfer mediums; visually inspecting components; conducting pressure and temperature differential tests; determining required pressures, flows, and velocities; adjusting air flow, fluid flows, filter media, pressures, or system components; replacing cracked or defective components; cleaning obstructed coils; using required hand tools, pressure gauges, thermometers, brushes, voltmeters, chemical solutions, vacuum, and power washers; and, documenting results; so that the heat exchanger is operational and functioning in accordance with work order, design parameters, manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.11 Adjust and replace heat transfer medium by following required procedures including (not limited to): visually checking air and fluid levels; checking air volumes, water, glycol strength, and refrigerant charge; adjusting levels; replacing mediums; and, using required hand tools, gauges, psychrometers, thermometers, pressure gauges, hydrometers, and chemicals; so that the quality and quantity of the transfer medium is maintained in accordance with manufacturer’s specifications, system performance data, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
47
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.12 Test or replace AC and HP electrical heaters, HRV/ERV and electronic air
cleaners by following required procedures including (not limited to): visually inspecting for discolouration, odours, moisture, and corrosion; checking terminal connectors; performing resistance measurements; checking and repairing sequencers; checking operational sequencers; using hand or power tools, speciality tools, and multimeters; and, documenting results; so that the equipment is working to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.13 Replace or repair system piping by following required procedures including (not limited to): reading and interpreting job documentation; checking pumps, strainers, valves, gauges, insulation, supports, and piping; repairing or replacing defective piping, parts, or components; checking piping chaseway; brazing, soldering, or welding piping; using required hand and power tools, multimeter, flow meter, pressure gauge, and brazing, soldering, or welding equipment; and, documenting results; so that the piping system is restored and functioning according to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.14 Replace or repair AC and HP condensate drains and accessory components by following required procedures including (not limited to): visually inspecting drain piping, drain pans, humidifiers, and condensate pumps; checking operation, condition, and integrity of the components; replacing defective or worn parts; repairing pumps and defective wiring; using hand tools, chemical solutions, brushes, and psychrometer; and, documenting results; so that the condensate components are operational and functioning in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
48
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.15 Check system for leakage by following required procedures including (not
limited to): checking gas and power sources, checking water, lubricants, and refrigerants; visually inspecting duct work; making necessary adjustments; and, using required hand tools, pressure gauges, and detectors; so that the system is leak free and is functioning to design parameters in accordance manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.16 Replace air cooling compressor by following required procedures including (not limited to): visually inspecting compressor; determining cause of compressor failure; performing acid test; replacing defective compressor; recharging system; performing start up of compressor; cleaning up work area; using hand or power tools, multimeters, compound gauges, recovery equipment, vacuum pump, and brazing equipment; and, documenting start-up parameters; so that the restored system performance meets design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.17 Clean or replace AC and HP filter system and components by following required procedures including (not limited to): inspecting air filters; measuring pressure differentials; checking temperature differentials; checking filter drier; cleaning or replacing filters; and, using hand tools, gauges, cleaning solutions, and thermometers; ensuring that the filter system is maintained and functioning to design parameters, in accordance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
49
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.18 Replace or repair the air side of AC and HP equipment by following required
procedures including (not limited to): discussing with client problems such as high humidity, moulds, allergies, temperature swings, or general comfort levels; checking humidifiers, exhaust fans, HRV/ERV, dehumidifiers, and filtration equipment; replacing damaged or dirty media; cleaning coils, components, and condensate drain system; repairing dampers, actuators, or controls; performing test run; using hand or power tools, brazing, soldering, or welding equipment, electrical metres, pressure gauges, and psychrometers; and, documenting results; so that the air quality is restored to design parameters, in accordance with manufacturer’s specifications, company standards/policies, customer requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.19 Replace or repair air handler components by following required procedures including (not limited to): visually inspecting filters, coils, fans, motors, bearings, belt and pulleys; checking amperage of motors; checking air volume; cleaning and lubricating parts; replacing worn belts and bearings; replacing motors and bearings; repairing or replacing damaged coil by brazing, soldering, or re-piping; using required hand or power tools, ammeters, multimeters, flow meters, pressure gauges, and brazing or soldering equipment; so that the air handler is restored to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Codes, Legislation and Regulations.
Date Completed Apprentice Supervisor/Trainer
50
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.20 Replace or repair AC and HP fans and motors by following required
procedures including (not limited to): visually inspecting fan assembly, motors, bearings, pulleys, and belts; checking vibrations and running amperage; replacing or repairing defective components; lubricating bearings; cleaning fan and associated components; documenting results; and, using hand or power tools, measuring devices, gauges, thermometers, speciality tools, lubricants, and cleaning chemicals; so that the performance of the fans and motors is restored to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.21 Check operations and functions of total AC and HP system by following required procedures including (not limited to): discussing with client to determine air quality and to define problems; inspecting and checking operation and integrity of system; calibrating and making adjustments; using hand tools, pressure gauges, thermometers, and psychrometers; and, documenting results; so that the system is maintained to maximize performance and to prevent damage, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6241.22 Complete AC and HP service and maintenance records by recording system operational parameters on manufacturer’s or company check lists and warranty forms, ensuring that the documents are completed in a clear, concise, and legible manner in accordance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
51
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6241.00 SERVICE OR MAINTAIN AIR COOLING (AC) AND HEAT PUMP (HP) ...cont’d
6241.23 Clean-up work site by: cleaning up liquids, broken pieces, and debris; replacing
structures; removing all construction waste; and, using brooms or wet/dry vac, so that the work area is clean and clear of obstructions, tools or equipment are stored, and hazardous products are disposed of in compliance with environmental protocols, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
52
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
GENERAL PERFORMANCE OBJECTIVE
Install and commission refrigeration and air conditioning (R&AC) system by: reading and interpreting installation and start-up documentation; inspecting system, accessories, and components at work site; performing a site evaluation; preparing work site; coordinating permits, inspection, and sub-trades; preparing site for installation; assembling and installing system, accessories, and components; assembling, joining, and installing piping; checking refrigerant and component piping for leaks; assembling and installing electrical system accessories and components; evacuating and dehydrating system; commissioning system; completing installation and commissioning records; and cleaning up work site.
PERFORMANCE OBJECTIVES
SKILLS
6242.01 Read and interpret R&AC installation and start up documentation including (not limited to) Installation Operation and Maintenance Instructions (IOM), manufacturer’s specifications, architectural and mechanical engineering drawings, wiring diagrams, job specifications, and applicable Acts, Regulations, Legislation, and Codes to identify: type, size, and manufacture of equipment; required permits; legislative requirements; required sub-trades; installation sequence and procedures; parts and accessories; material handling equipment; locations; required tools; equipment and materials; work schedules; and, any information needed to plan the completion of the installation.
Date Completed Apprentice Supervisor/Trainer
53
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.02 Inspect the R&AC system, accessories, and components at work site by
following required procedures including (not limited to): removing packaging; inspecting unit for damage; and, checking equipment design parameters; to ensure that the system parameters conform to work order, architectural and mechanical engineering drawings, manufacturer’s specifications, and company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6242.03 Perform a work site evaluation by following required procedures including (not limited to): visually inspecting site for obstructions; measuring equipment parameters; evaluating effectiveness and viability of installation site design; checking that required power and gas utilities are available; checking that equipment complies with job documentation; laying out mechanical chaseways; and, discussing with client the scope of the installation; so that the installation plan is checked and coincides with the scope of work and design parameters, client requirements, industry and company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.04 Prepare work site by following required procedures including (not limited to): setting up and arranging installation tools and equipment; checking that utilities are available; recovering, reusing, or deposing of refrigerant; removing and disposing of existing equipment and packaging materials; removing obstacles and debris from work area; placing system accessories and components to layout; and, using hand or power tools and material handling equipment; so that the work site is prepared and ready for the installation of the system in accordance with layout design, company standards/policies, client requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
54
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.05 Coordinate permits, inspections, and sub-trades to ensure that all permits and
inspections have been arranged prior to installation and that sub-trades have been contacted and scheduled, in compliance with industry or company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.06 Prepare site for installation by following required procedures including (not limited to): visually checking site; preparing job site conditions to the layout design; locating equipment to layout design; and, mounting on required supports including (not limited to) stanchions, columns, slabs, curbs, welded brackets, sleepers, pads, and hangers; so that the R&AC unit and components are located, positioned, and aligned in accordance with installation plan, work order, customer requirements, industry and company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.07 Assemble and install R&AC system, accessories, and components by following required procedures including (not limited to): coordinating sub-trades; preparing mechanical chaseways; coordinating installation of utilities; lifting and moving the R&AC components and equipment; connecting all components; checking that all accessories or components are complete; levelling system; welding, anchoring or fastening system components; and, using shims, fasteners, required tools, welding equipment, instruments, and material handling equipment; ensuring that the system is installed in accordance with installation plan, layout design, work order, customer requirements, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
55
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Date Completed Apprentice Supervisor/Trainer
56
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.08 Assemble R&AC piping and components including (not limited to) condensate
and water lines, secondary refrigerant lines, water regulating valves, pressure valves, strainers, chemical feeders, hangers, and floats, by following required procedures including (not limited to): coordinating gas trades; soldering; threading; cutting; brazing; welding; and, using torches, brazing, soldering, welding, and cutting equipment, threaders, reamers, vise, wrenches, groovers, flaring tools, pipe cutters, oil, and compounds; so that the piping and components are assembled in accordance with manufacturer’s specifications, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.09 Join and install R&AC piping by following required procedures including (not limited to): setting up oxygen, acetylene, propane, soldering devices, hoses, regulators, and torch accessories; inspecting and cleaning piping; brazing, soldering, welding, and cutting piping; preparing mechanical chaseways; purging the piping; using safety equipment and fire extinguishers, sil-fosTM, soft and hard solders, and nitrogen; and, cleaning, storing, and adjusting brazing, soldering, welding, or cutting equipment; so that the piping is joined and installed in compliance to manufacturer’s specifications, applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.10 Check refrigerant piping for leaks by following required procedures including (not limited to): visually inspecting piping; performing various leak tests using gauges, soap solutions, ultrasonic leak detectors, micron gauge, and nitrogen; and, evacuating system; in order to verify that there are no leaks and that the system integrity conforms to design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.11 Check component piping for leaks by following required procedures including
(not limited to): visually inspecting piping; pressurizing lines; performing various leak tests using gauges, soap solutions, or time-pressure test; and, using compressed dry air, nitrogen, and gauges; in order to verify that there are no leaks and that the system integrity conforms to design parameters, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.12 Assemble and install R&AC electrical system accessories and components by following required procedures including (not limited to): inspecting fuses, internal unit power wiring, system control wiring, and controls; reading and interpreting electrical diagrams, schematics, and IOM specifications; coordinating required sub-trades; checking permits; checking power capacity and voltage; checking system control wiring and controls; installing valves, controls, switches, wiring, and motors; and, using required hand or power tools, measuring devices, and electrical measuring devices; so that the unit electrical system is assembled and installed for system operation in accordance with design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.13 Evacuate and dehydrate R&AC system by following required procedures including (not limited to): releasing nitrogen from system; evacuating system; and, using hand tools, manifold gauges, vacuum pumps, micron gauges, or thermistor; so that all moisture and non-condensables are removed from system and the equipment is cleaned and ready for operation, in accordance with work order, design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
57
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.14 Commission R&AC system by following required procedures including (not
limited to): verifying that all sub-trade work has been inspected and certified; verifying that all gas operations have been checked and certified; turning on power and starting up system; setting limit, operating, and safety controls; testing system parameters including pressure, temperatures, flow rate, voltage, amperage, fluid levels, and speeds; making required adjustments; balancing the system oil charge; using hand or power tools, pressure gauges, temperature measuring instruments, flow measuring instruments, electrical measuring devices, level indicators, simulators, or tachometers; and, documenting results; so that the total system is verified to be operational and functioning in accordance with design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6242.15 Complete the installation and commissioning records by recording system operational parameters on manufacturer’s or company check lists and warranty forms, ensuring that the documentation is completed in a clear, concise, legible, and accurate manner in accordance with design parameters, IOM specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
58
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6242.00 INSTALL AND COMMISSION REFRIGERATION AND AIR CONDITIONING SYSTEM (R&AC) ...cont’d
6242.16 Clean-up work site by: cleaning up liquids, broken pieces, and debris; replacing
structures; removing all construction waste; and, using brooms or wet/dry vac; so that the work area is clean and clear of obstructions, tools or equipment are stored, and hazardous products are disposed of in compliance with environmental protocols, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
59
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6243.00 MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
GENERAL PERFORMANCE OBJECTIVE
Maintain refrigeration and air conditioning (R&AC) system by: troubleshooting system; cleaning and maintaining filter, condenser, evaporator, humidifier, and electrical components; checking operation and functions of total system; cleaning up work site; completing maintenance documents.
PERFORMANCE OBJECTIVES
SKILLS
6243.01 Troubleshoot R&AC systems and components by following required procedures including (not limited to): discussing with client to determine nature of call; performing an inspection and diagnostic check; reading and interpreting IOM charts; determining corrective actions or options; estimating cost of work; writing up a work sheet; and, using metres, gauges, and price lists; so that the extent of maintenance is determined and documented in accordance with company standards/policies, client requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6243.02 Clean and maintain R&AC filters and components by following required procedures including (not limited to): visually inspecting controls, rack, frames, filter, filter media, drive mechanisms, and air-flow sensors; checking filter loading; testing air flow; performing shut down and lock out procedures; replacing defective parts and filter media; cleaning filter and components; using required tools and equipment; and, documenting results; so that the air flow parameters are restored to design parameters, in accordance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
60
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6243.00 MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6243.03 Clean and maintain R&AC condenser, evaporator, and accessory components by following required procedures including (not limited to): inspecting receivers, cooling tower, heat exchangers, pumps, drain pan, nozzles, motors, coils, fans, dampers, baffles/fills, floats, and drive mechanisms; checking temperatures, leaks, flow rates, pressure relief valve, vibration, noise, lime build- up, dirt, bleed rates, water colour, odour, and levels; performing shut down and lock out procedures; performing defrosting procedures; cleaning components by scraping, flushing, washing, and brushing; blowing out with compressed air; applying chemical treatments; replacing defective components; using required chemicals, tools and equipment; and, documenting results; so that the water flow and air flow are restored to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6243.04 Clean and maintain R&AC humidifier and components by following required procedures including (not limited to): checking water level, flow feeds, condensate, controls, safeties, media, electrical devices, reservoir, dirt, and scaling; performing shut down and lock out procedures; cleaning by scraping, brushing, flushing contaminants, and vacuuming; chemically treating the unit; lubricating moving parts; replacing defective components, media, cylinders, controls, safeties, valves, floats, pans, lights, elements, and strainers; and, using required chemicals, lubricants, tools, and equipment; so that the level of humidification is restored to set points, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
61
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6243.00 MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6243.05 Clean or replace R&AC electrical components by following required
procedures including (not limited to): inspecting contactors, relays, heaters, solenoids, wiring, switches, and controls; checking discolouration, temperatures, pitting, voltage or amperage, resistance, wiring, and insulation; performing shut down and lock out procedures; applying chemical cleaners; brushing; vacuuming; replacing defective components; and, using required chemicals, tools, and equipment; so that all the electrical components are operational and functioning to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6243.06 Check operation and functions of total R&AC system by following required procedures including (not limited to): discussing with client to determine air quality and to define problems; inspecting and checking operation and integrity of system; calibrating and making adjustments; documenting results; and, using hand tools, pressure gauges, thermometers, and psychrometers; so that the system is maintained to maximize performance and to prevent damage, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6243.07 Clean up work site by: cleaning up liquids, broken pieces, and debris; replacing structures; removing all parts that have been replaced; and, using brooms or wet/dry vac; so that the work area is clean and clear of obstructions, tools or equipment are stored, and hazardous products are disposed of, in compliance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
62
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6243.00 MAINTAIN REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6243.08 Complete R&AC maintenance documentation by recording system operational parameters on manufacturer’s or company maintenance and servicing check lists or warranty forms, ensuring that all documentation is completed in a clear, concise, and legible manner, in accordance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
63
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM
GENERAL PERFORMANCE OBJECTIVE
Service refrigeration and air conditioning (R&AC) system by: checking R&AC system; replacing or repairing mechanical components, condensate components, piping, refrigerant system, open, semi-hermetic, or hermetic compressors, fans, pneumatics, controls and switches, Variable Air Volume components, metering devices, and electrical and electronic system; decommissioning packaged and split-system equipment to be salvaged; decommissioning equipment for demolition; cleaning up worksite; completing servicing documentation.
PERFORMANCE OBJECTIVES
SKILLS
6244.01 Check R&AC system accessories and components by following required procedures including (not limited to): discussing with client to determine the nature of call; performing an inspection and diagnostic check; reading and interpreting IOM charts; determining corrective actions or options; estimating cost of job; writing up work sheet; and, using metres, gauges, and price lists; so that the extent of required service work is determined and documented, in accordance with company standards/policies, client requirements, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
64
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.02 Replace or repair R&AC mechanical components by following required procedures including (not limited to): inspecting belts, drives, bearings, linkage, dampers, and switches; testing clearances, operations, alignment, flows, pressures, temperatures, voltage, and amperage; checking for wear, cracks, mismatches, shredding, tension, slippage, grooving, noise, and vibration; performing shut down and lock out procedures; making adjustments and repairs; replacing defective parts; using required testing devices, tools and equipment; and, documenting results; so that all the mechanical components are operational and functioning to design parameters, in accordance with manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.03 Repair or replace R&AC condensate components by following required procedures including (not limited to): inspecting pumps, drain pan, piping, and switches; checking for pressures, algae, dirt, leaks, and odours; performing shut down and lock out procedures; repairing defective drain pan and piping; cleaning components by scraping, flushing, and vacuuming; blowing out unit with compressed air; chemically treating the unit; using required chemicals, tools, and equipment; and, documenting results; to ensure the purity and flow of water and that the condensate equipment is operational and functioning, in accordance with design parameters, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
65
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.04 Repair or replace R&AC piping, accessories, and components by following required procedures including (not limited to): checking leaks, cracks, wear, rust, bulges, insulation, heat tracing, supports, flow, and pressures; performing shut down and lock out procedures; replacing defective piping, components, and supports; restoring defective insulation; repairing defective components by cutting, fitting, brazing, soldering, welding, gluing, flaring, and swaging; using required piping, materials, tools, and equipment; and, documenting results; so that the flow of fluids is maintained to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.05 Repair or replace R&AC refrigerant system, components, and accessories by following required procedures including (not limited to): checking fluid and refrigerant levels, pressures, temperatures, concentration, and leaks; performing pressure and leak tests; performing shut down and lock out procedures; repairing pump-down system; brazing; soldering; welding, gluing; fitting; cutting; evacuating system; cleaning components; replacing defective parts; recharging with refrigerant; and, using required refrigerants, tools, testing devices, or equipment; so that the charge (secondary and primary refrigerants) are restored to the specified levels, temperatures, and pressures, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
66
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.06 Repair or replace R&AC open, semi-hermetic, or hermetic compressor by
following required procedures including (not limited to): checking and testing amperage draw, operating pressures, temperatures, motor winding resistance, capacity controls, vibration, clearances, oil levels, lubrication, safeties, and motors; performing shut down and lock out procedures; isolating compressor from system; pumping down refrigerant; replacing oil pumps, heads, valve plates, gaskets, mounts/supports, filters, switches, safeties, electrical connectors, and lubricants; and, using required lubricants, chemicals, testing devices, tools, and equipment; so that the efficiency of the compressor is restored to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.07 Repair or replace R&AC fans and components by following required procedures including (not limited to): checking noise, vibration, dirt, air flow, alignments, balance, drive mechanism, and bearings; performing shut down and lock out procedures; cleaning by vacuuming, brushing, and power washing; replacing defective bearings, bushings, pulleys, belts, blowers, housings, shafts, and motors; and, using required tools and equipment; so that the air flow is restored to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
67
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.08 Repair or replace R&AC pneumatics by following required procedures including (not limited to): checking or testing pressures, filters, auto drains, motors, compressors, belts, pulleys, oil levels, driers, controls, safety devices, solenoids, calibration, piping, air leaks, and supports; performing shut down procedures; cleaning components; repairing by soldering and swaging; calibrating pneumatics; replacing defective components; and, using required tools and equipment; so that the pneumatic control pressure is maintained, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.09 Replace R&AC controls and switches by following required procedures including (not limited to): checking or testing operations, resistance, voltage, and safety devices; performing shut down procedures; cleaning components; making required adjustments; calibrating set points; replacing defective parts; and, using required testing devices, tools, and equipment; so that all the controls and switches are operational and functioning, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.10 Repair or replace Variable Air Volume (VAV) components by following required procedures (not limited to): checking or testing open or close motions, modulation variables, calibration, travel, and pressures; cleaning; sealing; tightening; soldering; making required adjustments; calibrating set points; replacing defective components including damper motors, linkages, dampers, sensors, controls, or safety devices; and, using required testing devices, tools, and equipment; so that the air flow volumes are maintained to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
68
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.11 Repair or replace R&AC metering devices by following required procedures (not limited to): checking or testing pressures, temperatures, voltages, fluid levels, leaks, and insulations; adjusting valves; brazing; soldering; cleaning; tightening; calibrating; replacing insulation, supports, gaskets, cages, valves, and screens; and, using required testing devices, tools, and equipment; so that all the devices are operational and functioning to design parameters, in accordance with manufacturer’s and job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.12 Replace or repair R&AC electrical and electronic system and components by following required procedures including (not limited to): inspecting unit panel, fuses, internal unit power wiring, systems control wiring and controls, switches, and safety devices; reading and interpreting electrical diagrams, schematics, and IOM specifications; coordinating required sub-trades; checking permits; checking power capacity and voltage; checking control wiring and controls; replacing defective system wiring; checking and replacing valves, controls, switches, actuators, transducers, electronic components, electronic air cleaners, electronic and logic controllers, heaters, and motors; and, using required hand or power tools, measuring instruments, or electrical measuring devices; so that the electrical system is restored to design parameters, in accordance with IOM specifications, manufacturer’s specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
69
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.13 Decommission packaged R&AC equipment to be salvaged for resale,
renovation, or mothballing by following required procedures including (not limited to): discussing with client to determine what is happening with the system after decommissioning; checking that utilities connected to the system have been shut off and locked out; disconnecting system and accessories; removing fluids subject to freezing; packing system in required containers; using required hand or power tools, material handling equipment, and safety equipment; and, completing documentation; so that the packaged system is ready for transportation, in accordance with work order, industry standards, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.14 Decommission split-system R&AC equipment to be salvaged for resale, renovation, or mothballing by following required procedures including (not limited to): discussing with client which system is to be decommissioned; checking that utilities connected to the system have been shut off and locked out; disconnecting system and accessories; pumping down system to reclaim refrigerant; removing fluids subject to freezing; sealing system; using required hand or power tools, material handling equipment, and safety equipment; and, completing documentation; so that the split system is sealed and ready for transportation, in accordance with work order, industry standards, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
70
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6244.00 SERVICE REFRIGERATION AND AIR CONDITIONING (R&AC) SYSTEM ...cont’d
6244.15 Decommission R&AC equipment for demolition by following required procedures including (not limited to): discussing with client which system is being demolished; checking that utilities connected to the system have been shut off and locked out; disconnecting system and accessories; pumping down system to reclaim/recover fluids including refrigerants, oils, secondary refrigerants, brines, and glycol solutions; placing tags indicating that system has been decommissioned; using required hand or power tools, fluid containers, and safety equipment; and, completing documentation; so that all fluids are reclaimed for storage or disposal and the R&AC system is ready for demolition, in accordance with work order, industry standards, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.16 Clean up work site by: cleaning up liquids, broken pieces, and debris; replacing structures; removing all parts that have been replaced; and, using brooms or wet/dry vac; so that the work area is clean and clear of obstructions, tools or equipment are stored, and hazardous products are disposed of, in compliance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6244.17 Complete servicing documentation by recording system operational parameters on manufacturer’s or company servicing check lists and warranty forms, ensuring that all documentation is completed in a clear, concise, and legible manner in accordance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
71
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6245.00 PERFORM CUSTOMER SERVICE
GENERAL PERFORMANCE OBJECTIVE
Perform customer service by: determining nature of service or maintenance call; conducting a site evaluation; performing a diagnostic inspection; estimating costs of service or maintenance; completing a servicing and/or maintenance schedule; completing job work order; and, instructing clients.
PERFORMANCE OBJECTIVES
SKILLS
6245.01 Determine nature of service or maintenance call by discussing problems with client, asking clear and concise questions, listening, and repeating back what is heard, so that the client’s concerns are clearly identified and understood before proceeding with a diagnostic check.
Date Completed Apprentice Supervisor/Trainer
6245.02 Conduct a site evaluation by checking the general condition of the system, equipment, and surrounding environment or facilities, in order to assist in determining the nature and scope of the service or maintenance request, ensuring that the evaluation is carried out in accordance with job specifications, company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
72
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6245.00 PERFORM CUSTOMER SERVICE …cont’d
6245.03 Perform a diagnostic inspection by following required procedures including (not limited to): reading and interpreting IOM documentation, work order, manufacturer’s specifications, architectural and mechanical engineering drawings, and applicable Acts, Regulations, Legislation, and Codes; identifying the type, size, and capacity of equipment, system components, and parts; inspecting and checking operation and integrity of system; performing tests and checks of all parts of the system; determining set-points of each part of the system; and, checking efficiency outputs and parameters of the system; so that the system defects or faults are identified for further servicing or maintenance.
Date Completed Apprentice Supervisor/Trainer
6245.04 Estimate costs of service or maintenance call by: determining corrective actions or options for repair or replacement; calculating time frames, labour, parts, or equipment costs; using work orders, costing lists, manuals, and other documentation; communicating with employer or shop personnel to confirm the estimates; completing estimation sheet and bill of materials; going over quote with client; and, obtaining client’s signature of approval; so that the estimation sheets are completed and approved prior to undertaking service or maintenance work in accordance with company standards/policies.
Date Completed Apprentice Supervisor/Trainer
6245.05 Complete service or maintenance schedule which includes (not limited to): servicing or maintenance parameters and procedures, parts, labour and inspection personnel, equipment, sub-trades, material handling equipment, permits, hand tools, power tools, location and layout of system, dates and times, and, work orders, ensuring that the service or maintenance schedule is approved by employer and client.
Date Completed Apprentice Supervisor/Trainer
73
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
6245.00 PERFORM CUSTOMER SERVICE …cont’d
6245.06 Complete job work order after service or maintenance work has been completed to identify: parts and components used; labour costs; nature and scope of service or maintenance work; time taken; unit identification; warranty coverage and obligations; tools and equipment used; completion dates; and, system operation parameters; by recording information on manufacturer’s or company servicing or maintenance check lists and warranty forms, ensuring that all information is clear, legible, and concise in accordance with company standards/policies, and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
6245.07 Instruct clients on equipment operation, routine maintenance or servicing procedures and location of controls or safety devices, by using verbal communication, written job specifications, and manufacturer’s specifications, ensuring that all instructions are given in a clear, concise, and precise manner and that the client has signed off on the work order, in accordance with company standards/policies and applicable Acts, Regulations, Legislation, and Codes.
Date Completed Apprentice Supervisor/Trainer
Sponsor/Employer Name Sponsor/Employer Signature
74
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
APPRENTICE RECORD
APPRENTICE NAME (Print):
SPONSOR/EMPLOYER INFORMATION
Training Agreement #
Name
Address
Telephone
E-mail Address
SUMMARY OF TRAINING
Employment Start Date
Employment End Date
Total hours of training & instruction between dates of employment
Date Completed Apprentice Supervisor/Trainer
75
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
APPRENTICE RECORD
APPRENTICE NAME (Print):
SPONSOR/EMPLOYER INFORMATION
Training Agreement #
Name
Address
Telephone
E-mail Address
SUMMARY OF TRAINING
Employment Start Date
Employment End Date
Total hours of training & instruction between dates of employment
Date Completed Apprentice Supervisor/Trainer
76
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
APPRENTICE RECORD
APPRENTICE NAME (Print):
SPONSOR/EMPLOYER INFORMATION
Training Agreement #
Name
Address
Telephone
E-mail Address
SUMMARY OF TRAINING
Employment Start Date
Employment End Date
Total hours of training & instruction between dates of employment
Date Completed Apprentice Supervisor/Trainer
77
Refrigeration and Air Conditioning Systems Mechanic - Branch 1
Ontario College of Trades ©
APPRENTICE COMPLETION FORM
APPRENTICE NAME
Signature
Social Insurance Number
Skill Sets when completed should be signed by the Supervisor/Trainer and presented with this completion form to your local Apprenticeship Client Services Office. Any supporting documentation should also be attached.
In-School Completed Yes ( ) No ( ) Not applicable ( ) (Proof to Be Provided)
Hours completed as per Contract: Yes ( ) No ( ) Not applicable ( )
SPONSOR/EMPLOYER INFORMATION
Name
Address
Telephone
E-mail Address
Signature of Signing Authority
78
You will be required to disclose this signed form to the Ministry of Training, Colleges and Universities in order to complete your program. The Ministry will use your personal information to administer and finance Ontario’s apprenticeship training system.For further information please see the notice/declaration for collection of personal information that is referenced in the table of contents of this training standard.