api 581

40
API RP 581 RISK-BASED INSPECTION TECHNOLOGY 2.E-2 API 581 Part 2 Ballot Title: POF Calculations (RSF Approach) Date: March 3, 2012 Contact: Name: Phil Henry/David Osage/Rouhua Guo Company: Equity Engineering Phone: 216-283-6012 E-mail: [email protected] Purpose: Provide new Appendix 2E to API 581 Part 2 for Level 2 method fro determination of POF based on RSF approach A complete description of the numerical method for calculating POF and DFs using this new approach is fully documented in a soon to be released WRC Bulletin which includes a comparison to the existing AR/T approach and includes sensitivity studies. Source: WRC Bulletin XYZ Revision: 1 Impact: The second edition of API 581 Part 2 provides Damage Factors for thinning using AR/T tables based on older technology. These tables are remaining as the Level 1 approach to POF determination and are moving to a new Annex D. The new Annex E covered in this ballot is based on utilization of an alternate limit state equation which can be expanded to included local thinning effects using an RSF approach. Additionally, the original approach is being enhanced to eliminate some of the artifacts that were used to simplify the original procedure in the BRD (API Publication 581). The new tables can be used across a wider range of vessel diameters, corrosion rates and corrosion allowances (excess metal thickness). Damage factors will change, in general, they will be lower for smaller values of AR/T and greater for high values of AR/T. With this proposed modification, all DF tables are referenced to 0 so that DFs can go below 1.0. This allows the total DF to be less than 1.0 and will result in some components POF to go below the GFF, which is known to be too conservative.

Upload: arturo-de-la-fuente

Post on 18-Jul-2016

86 views

Category:

Documents


116 download

DESCRIPTION

Part 2 and next level 2

TRANSCRIPT

Page 1: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-2

API 581 Part 2 Ballot Title: POF Calculations (RSF Approach)

Date: March 3, 2012

Contact: Name: Phil Henry/David Osage/Rouhua Guo

Company: Equity Engineering

Phone: 216-283-6012

E-mail: [email protected]

Purpose: Provide new Appendix 2E to API 581 Part 2 for Level 2 method fro determination of POF based on RSF approach

A complete description of the numerical method for calculating POF and DFs using this new approach is fully documented in a soon to be released WRC Bulletin which includes a comparison to the existing AR/T approach and includes sensitivity studies.

Source: WRC Bulletin XYZ

Revision: 1

Impact: The second edition of API 581 Part 2 provides Damage Factors for thinning using AR/T tables based on older technology. These tables are remaining as the Level 1 approach to POF determination and are moving to a new Annex D.

The new Annex E covered in this ballot is based on utilization of an alternate limit state equation which can be expanded to included local thinning effects using an RSF approach. Additionally, the original approach is being enhanced to eliminate some of the artifacts that were used to simplify the original procedure in the BRD (API Publication 581). The new tables can be used across a wider range of vessel diameters, corrosion rates and corrosion allowances (excess metal thickness). Damage factors will change, in general, they will be lower for smaller values of AR/T and greater for high values of AR/T.

With this proposed modification, all DF tables are referenced to 0 so that DFs can go below 1.0. This allows the total DF to be less than 1.0 and will result in some components POF to go below the GFF, which is known to be too conservative.

Page 2: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-3

API RP 581 PART 2

ANNEX 2.E – DETERMINATION OF LEVEL 2 THINNING DAMAGE FACTOR

Page 3: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-4

PART CONTENTS

2.E.1  OVERVIEW ..................................................................................................................... 5 2.E.2  CALCULATION OF THINNING DAMAGE FACTOR .................................................... 5 2.E.3  CALCULATION OF EXTERNAL DAMAGE FACTOR .................................................. 6 2.E.4  REFERENCES ............................................................................................................... 7 2.E.5  NOMENCLATURE ......................................................................................................... 8 2.E.6  TABLES .......................................................................................................................... 9 2.E.7  FIGURES ...................................................................................................................... 40 

Page 4: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-5

2.E.1 OVERVIEW API 581 Part 2 provides the User with the option of calculating a damage factor using the original Level 1 approach (Annex D) or a Level 2 approach provided in this Annex.

The Level 2 approach is fully documented in a WRC Bulletin [1]. Based on user requests and available technology, significant enhancements to the existing procedure to determine the thinning damage factor are being provided in the Level 2 method. These enhancements include;

a more accurate limit state function that is flexible and can be used for many types of components such as thin and thick wall vessels, formed heads, nozzles and conical transitions,

the ability to explicitly model internal and external corrosion rate, a more accurate analytical model for inspection effectiveness, the incorporation of an RSF factor as defined by API 579-1/ASME FFS-1 for modeling of local corrosion

and pitting, a more accurate representation of material properties, a state-of-art statistical algorithm that permits any type of distribution (i.e. normal, lognormal, Weibull,

beta, Gumball, etc.) to be used in modeling the independent variables, and the use of a continuous distribution on corrosion rate, which results in POF curves that are smooth and

continuously increasing with damage, i.e. classical POF curves expected for structures subject to time dependent damage.

2.E.2 CALCULATION OF THINNING DAMAGE FACTOR The following procedure may be used to determine the Level 2 damage factor for thinning, see Figure 2.B.1. Note that this procedure makes the assumption that the cladding corrodes prior to any corrosion of the base metal. Where thinning due to external corrosion exists, this procedure will be conservative.

a) STEP 1 – Complete STEPs 1 thru 5 of Part 2 Section 5.0 to determine:

the number and the corresponding inspection effectiveness category used for all past inspections, the in-service age for corrosion, age ,

the starting thickness, rdt , which is either last measured thickness or the furnished thickness,

the corrosion rate for the base metal, ,r bmC ,

the corrosion rate for the cladding, if applicable, ,r cmC ,

the minimum required wall thickness, mint ,

and the remaining age of the cladding, rcage , if applicable.

b) STEP 2 – Determine the excess metal thickness ratio, xsr , using Equation (2.E.1) based on the minimum

required thickness, mint ,

min

min min

rdt t FCAxsr

t t

(2.E.1)

Note that a negative value for xsr is possible, for cases where the starting thickness is already below mint .

c) STEP 3 – Determine the rtA parameter using Equation (2.E.2) or (2.E.3), based on the starting thickness,

rdt , the age , the rC , and the age required to corrode away the cladding, rcage , if applicable from STEP 1.

Note that for thinning the age used to determine the rtA is equal to tkage .

Page 5: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-6

1) For components without cladding, and for components where the cladding is corroded away at the

time of the last inspection (i.e. 0.0rcage ), use Equation (2.E.2).

,r bmrt

rd

C ageA

t

(2.E.2)

2) For components that have cladding (i.e. 0.0rcage ) at the time of the last inspection, use Equation

(2.E.3) :

, ,r cm rc r bm rcrt

rd

C age C age ageA

t

(2.E.3)

d) STEP 4 – Determine the base damage factor for thinning, thinfBD , using Table 2.B.1 through Table 2.B.30,

as applicable, based on the number of, and highest effective inspection category from STEP 1, the

corrosion rate, rC , from STEP 1, the excess metal thickness ratio, xsr , from STEP 2 and the rtA

parameter from STEP 3 .When using Tables 2.B.1 through Table 2.B.30, linear interpolation between tables is permitted. As an alternative, a conservative table selection can be made by choosing the table based on a lower corrosion rate and/or a lower excess metal thickness ratio than the values obtained in STEP 1 and STEP 3, respectively. For cases where the excess metal ratio calculated in STEP 3 is negative, a table should be selected with an excess metal thickness ratio equal to 0.0 with an adjustment to the AR/T value.

1) For components without cladding, and for components where the cladding is corroded away at the

time of the last inspection (i.e. 0.0rcage ), the corrosion rate of the base material, ,r bmC , should be

used for purposes of selecting the appropriate damage factor table.

2) For components that have cladding (i.e. 0.0rcage ) at the time of the last inspection, the corrosion

rate of the clad material, ,r cmC , should be used when selecting the appropriate damage factor table.

2.E.3 CALCULATION OF EXTERNAL DAMAGE FACTOR The following procedure may be used to determine the Level 2 damage factors for external corrosion damage,

extcorfD (See Part 2 Section 16.0) or the CUI damage factor, CUIF

fD , (See Part 2 Section 17.0). See Figure

2.E.2.

a) STEP 1 – Complete STEPs 1 thru 7 of Part 2 Section 16.0 or 17.0, as applicable to determine:

the number and the corresponding inspection effectiveness category used for all past inspections,

the in-service age for external corrosion, age ,

the starting thickness, rdt , which is either last measured thickness or the furnished thickness,

the corrosion rate for external damage, rC ,

and the minimum required wall thickness, mint ,

b) STEP 2 – Determine the excess metal thickness ratio, xsr , using Equation (2.E.4) based on the minimum

required thickness, mint ,

min

min min

rdt t FCAxsr

t t

(2.E.4)

Page 6: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-7

Note that a negative value for xsr is possible, for cases where the starting thickness is already below mint .

c) STEP 3 – Determine the rtA parameter using Equation (2.E.5) , based on the starting thickness, rdt ,

the age , and the rC from STEP 1, .

rrt

rd

C ageA

t

(2.E.5)

d) STEP 4 – Determine the damage factor for external corrosion, extcorfD , or the CUI damage factor, CUIF

fD ,

as applicable, using Tables 2.E.1 through 2.E.30, as applicable, based on the number of, and highest

effective inspection category and the corrosion rate, rC , from STEP 1, the excess metal thickness ratio,

xsr , from STEP 2 and the rtA parameter from STEP 3. When using Tables 2.E.1 through 2.E.30, linear

interpolation between tables is permitted. As an alternative, a conservative table selection can be made by choosing the table based on a lower corrosion rate and/or a lower excess metal thickness ratio than the values obtained in STEP 2 and STEP 3, respectively. For cases where the excess metal thickness ratio calculated in STEP 3 is negative, a table should be selected with an excess metal thickness equal to 0.0 with an adjustment to the AR/T value.

2.E.4 REFERENCES 1. Guo, R.Z., Osage, D.A. and Henry, P.A., “Risk Based Inspection For Wall Thinning Damage Using API

Risk-Based Inspection Planning Technology.” WRC Bulletin XXX, Welding Research Council, New York,

Page 7: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-8

2.E.5 NOMENCLATURE age is the in-service time that the damage is applied

rcage is the time required or age from the last inspection date when the cladding is corroded away

tkage is the time since the last thickness reading or since the install date, if no acceptable thickness

measurements taken

rtA is the damage factor parameter

rC is the corrosion rate

,r bmC is the corrosion rate for the base metal

,r cmC is the corrosion rate for the cladding

CUIFfD is the damage factor for CUI for ferritic components

extcorfD is the damage factor for external corrosion

thinfBDF is the base value of the damage factor for thinning

t is the furnished thickness of the component base metal

rdt is the thickness reading stt is the starting thickness for the analysis

xsr is the excess metal thickness ratio

Page 8: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-9

2.E.6 TABLES

Page 9: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-10

Table 2.E.1 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.0

rtA  Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.01

0.06  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.01

0.08  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.01

0.10  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.01

0.12  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.01

0.14  0.32  0.31  0.29  0.27  0.23 0.29 0.27 0.23 0.17 0.28 0.25  0.20  0.12

0.16  6.22  6.08  5.76  5.40  4.75 5.76 5.40 4.75 3.58 5.63 5.08  4.17  2.60

0.18  41.0  40.3  38.5  36.4  32.8 38.5 36.4 32.8 25.9 37.7 34.7  29.5  20.9

0.20  134  132  127  121  112 127 121 112 92 125 117  103  77.7

0.25  613  615  598  580  553 598 580 553 490 594 570  526  443

0.30  1270  1270  1240  1220  1180 1240 1220 1180 1090 1240 1210  1140  1020

0.35  1930  1920  1890  1860  1820 1890 1860 1820 1720 1890 1860  1780  1640

0.40  2520  2520  2480  2450  2410 2480 2450 2410 2310 2480 2450  2380  2240

0.45  3030  3030  3000  2960  2930 3000 2960 2930 2830 3000 2970  2900  2770

0.50  3460  3470  3430  3400  3380 3430 3400 3380 3290 3450 3410  3350  3230

0.55  3840  3840  3810  3780  3760 3810 3780 3760 3680 3810 3790  3740  3630

0.60  4150  4160  4130  4100  4080 4130 4100 4080 4010 4130 4110  4070  3970

0.65  4420  4430  4400  4380  4360 4400 4380 4360 4300 4410 4390  4350  4270

rtA  Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.27  0.23  0.17  0.09  0.26  0.21  0.15  0.06  0.25  0.20  0.12  0.04 

0.16  6.22  5.40  4.75  3.58  2.07  5.21  4.25  3.17  1.48  5.08  4.17  2.60  1.11 

0.18  41.0  36.4  32.8  25.9  16.7  35.4  30.7  23.4  12.8  34.7  29.5  20.9  10.1 

0.20  134  121  112  92.2  64.9  119  106  84.9  52.5  117  103  77.7  43.5 

0.25  613  580  553  490  398  574  533  466  350  570  526  443  313 

0.30  1270  1220  1180  1090  950  1210  1110  1050  869  1210  1140  1020  808 

0.35  1930  1860  1820  1720  1570  1860  1790  1680  1470  1860  1780  1640  1390 

0.40  2520  2450  2410  2310  2160  2450  2380  2270  2060  2450  2380  2240  1980 

0.45  3030  2960  2930  2830  2700  2960  2900  2800  2590  2970  2900  2770  2520 

0.50  3460  3400  3380  3290  3170  3410  3350  3260  3070  3410  3350  3230  3000 

0.55  3840  3780  3760  3680  3580  3780  3730  3650  3480  3790  3740  3630  3420 

0.60  4150  4100  4080  4010  3930  4110  4060  3990  3840  4110  4070  3970  3790 

0.65  4420  4380  4360  4300  4240  4380  4340  4290  4150  4390  4350  4270  4110 

Page 10: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-11

Table 2.E.2 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.0625

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections C B A C B A C B A C C B

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.09  0.08  0.08  0.07  0.08  0.08  0.07  0.05  0.08  0.07  0.06  0.03 

0.16  2.82  2.75  2.59  2.42  2.11  2.59  2.42  2.11  1.56  2.53  2.26  1.83  1.16 

0.18  24.9  24.4  23.2  21.8  19.0  23.2  21.8  19.0  15.1  22.7  20.7  17.4  11.9 

0.20  96.0  94.5  90.7  86.3  78.8  90.7  86.3  78.8  64.1  89.3  83.0  71.9  53.1 

0.25  527  523  509  476  467  509  476  467  410  505  483  442  368 

0.30  1150  1150  1120  1100  1060  1120  1100  1060  973  1120  1090  1030  906 

0.35  1800  1790  1760  1730  1690  1760  1730  1690  1590  1760  1720  1650  1510 

0.40  2380  2380  2350  2320  2280  2350  2320  2280  2180  2350  2310  2240  2050 

0.45  2900  2900  2870  2830  2800  2870  2830  2800  2700  2870  2840  2770  2630 

0.50  3340  3350  3310  3280  3250  3310  3280  3250  3160  3320  3290  3230  3100 

0.55  3720  3730  3690  3660  3640  3690  3660  3640  3560  3700  3670  3620  3510 

0.60  4050  4050  4020  3990  3980  4020  3990  3980  3900  4030  4010  3960  3860 

0.65  4320  4330  4300  4280  4260  4300  4280  4260  4200  4310  4290  4250  4160 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.08  0.07  0.05  0.02  0.07  0.06  0.04  0.02  0.07  0.06  0.03  0.01 

0.16  2.82  2.42  2.11  1.56  0.86  2.32  1.93  1.36  0.59  2.26  1.83  1.16  0.43 

0.18  24.9  21.8  19.0  15.1  9.32  21.2  18.1  13.5  6.94  20.7  17.4  11.9  5.35 

0.20  96.0  86.3  78.8  64.1  43.6  84.3  74.3  58.6  34.6  83.0  71.9  53.1  28.2 

0.25  527  476  467  410  327  487  449  389  285  483  442  368  253 

0.30  1150  1100  1060  973  802  1090  1030  939  765  1090  1030  906  707 

0.35  1800  1730  1690  1590  1440  1730  1660  1550  1340  1720  1650  1510  1270 

0.40  2380  2320  2280  2180  2030  2320  2250  2140  1920  2310  2240  2050  1840 

0.45  2900  2830  2800  2700  2560  2840  2770  2670  2460  2840  2770  2630  2380 

0.50  3340  3280  3250  3160  3040  3280  3220  3130  2940  3290  3230  3100  2870 

0.55  3720  3660  3640  3560  3460  3670  3610  3530  3360  3670  3620  3510  3290 

0.60  4050  3990  3980  3900  3810  4000  3950  3880  3720  4010  3960  3860  3670 

0.65  4320  4280  4260  4200  4130  4280  4240  4180  4040  4290  4250  4160  3990 

Page 11: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-12

Table 2.E.3 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.125

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.03  0.02  0.02  0.02  0.02  0.02  0.02  0.01  0.02  0.02  0.02  0.01 

0.16  1.26  1.23  1.16  1.07  0.93  1.16  1.07  0.93  0.67  1.12  1.00  0.68  0.49 

0.18  15.1  14.7  14.0  13.1  11.6  14.0  13.1  11.6  8.85  13.7  12.4  10.3  6.85 

0.20  69.3  68.1  65.2  61.8  56.1  65.2  61.8  56.1  44.9  64.1  59.2  50.7  36.7 

0.25  453  450  436  422  394  436  422  394  347  433  413  376  302 

0.30  1050  1050  1020  998  963  1020  998  963  877  1020  988  928  814 

0.35  1680  1680  1650  1620  1580  1650  1620  1580  1480  1650  1610  1540  1400 

0.40  2270  2270  2240  2200  2170  2240  2200  2170  2060  2230  2190  2130  1990 

0.45  2790  2790  2760  2720  2690  2760  2720  2690  2590  2760  2720  2660  2520 

0.50  3240  3240  3210  3170  3150  3210  3170  3150  3050  3210  3180  3120  2990 

0.55  3620  3630  3590  3560  3540  3590  3560  3540  3450  3600  3570  3520  3400 

0.60  3950  3960  3930  3900  3880  3930  3900  3880  3800  3930  3910  3860  3760 

0.65  4240  4240  4210  4190  4170  4210  4190  4170  4110  4220  4200  4160  4070 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.02  0.02  0.01  0.01  0.02  0.02  0.01  0.01  0.02  0.02  0.01  0.01 

0.16  1.26  1.07  0.93  0.67  0.35  1.03  0.85  0.58  0.24  1.00  0.68  0.49  0.17 

0.18  15.1  13.1  11.6  8.85  5.23  12.7  10.8  7.86  3.79  12.4  10.3  6.85  2.85 

0.20  69.3  61.8  56.1  44.9  29.6  60.2  52.6  40.8  23.0  59.2  50.7  36.7  18.2 

0.25  453  422  394  347  272  416  382  328  235  413  376  302  206 

0.30  1050  998  963  877  730  992  936  845  680  988  928  814  625 

0.35  1680  1620  1580  1480  1330  1610  1550  1440  1230  1610  1540  1400  1160 

0.40  2270  2200  2170  2060  1910  2200  2130  2000  1800  2190  2130  1990  1730 

0.45  2790  2720  2690  2590  2450  2720  2660  2550  2340  2720  2660  2520  2260 

0.50  3240  3170  3150  3050  2920  3180  3110  3020  2820  3180  3120  2990  2750 

0.55  3620  3560  3540  3450  3350  3570  3510  3430  3250  3570  3520  3400  3180 

0.60  3950  3900  3880  3800  3710  3910  3850  3780  3620  3910  3860  3760  3560 

0.65  4240  4190  4170  4110  4030  4200  4150  4090  3940  4200  4160  4070  3890 

Page 12: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-13

Table 2.E.4 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.25

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.24  0.23  0.21  0.18  0.23  0.21  0.18  0.13  0.22  0.18  0.15  0.09 

0.18  5.54  5.41  4.99  4.76  4.15  4.99  4.76  4.15  3.06  4.98  4.46  3.60  2.28 

0.20  36.8  36.0  34.3  32.4  29.0  34.3  32.4  29.0  22.6  33.5  30.6  25.9  17.9 

0.25  343  340  329  317  297  329  317  297  255  326  309  278  223 

0.30  874  885  864  841  808  864  841  808  729  860  831  770  671 

0.35  1500  1500  1470  1440  1400  1470  1440  1400  1250  1440  1430  1360  1230 

0.40  2080  2080  2050  2010  1980  2050  2010  1980  1870  2040  2010  1940  1780 

0.45  2600  2600  2570  2540  2500  2570  2540  2500  2400  2570  2540  2470  2320 

0.50  3060  3060  3030  2990  2960  3030  2990  2960  2870  3030  3000  2930  2800 

0.55  3450  3460  3430  3390  3370  3430  3390  3370  3280  3430  3400  3340  3220 

0.60  3800  3800  3770  3740  3720  3770  3740  3720  3640  3770  3750  3700  3590 

0.65  4090  4100  4070  4040  4020  4070  4040  4020  3950  4070  4050  4010  3910 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.21  0.18  0.13  0.06  0.20  0.16  0.11  0.04  0.18  0.15  0.09  0.03 

0.18  5.54  4.76  4.15  3.06  1.68  4.57  3.81  2.68  1.15  4.46  3.60  2.28  0.83 

0.20  36.8  32.4  29.0  22.6  14.0  31.4  27.0  20.3  10.5  30.6  25.9  17.9  8.09 

0.25  343  317  297  255  194  312  284  239  164  309  278  223  142 

0.30  874  841  808  729  613  835  784  700  549  831  770  671  500 

0.35  1500  1440  1400  1250  1150  1430  1370  1260  1070  1430  1360  1230  998 

0.40  2080  2010  1980  1870  1720  2010  1940  1830  1620  2010  1940  1780  1540 

0.45  2600  2540  2500  2400  2250  2540  2470  2360  2140  2540  2470  2320  2070 

0.50  3060  2990  2960  2870  2730  3000  2930  2830  2630  3000  2930  2800  2550 

0.55  3450  3390  3370  3280  3160  3400  3340  3250  3060  3400  3340  3220  2990 

0.60  3800  3740  3720  3640  3540  3750  3690  3610  3440  3750  3700  3590  3380 

0.65  4090  4040  4020  3950  3860  4050  4000  3930  3770  4050  4010  3910  3720 

Page 13: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-14

Table 2.E.5 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.375

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.05  0.05  0.04  0.03  0.05  0.04  0.03  0.02  0.04  0.04  0.03  0.02 

0.18  2.07  2.01  1.89  1.75  1.51  1.89  1.75  1.51  0.98  1.84  1.63  1.29  0.78 

0.20  20.0  19.6  18.6  17.4  15.4  18.6  17.4  15.4  11.7  18.1  15.9  13.6  9.03 

0.25  267  264  255  245  229  255  245  229  193  253  238  213  167 

0.30  769  765  746  725  693  746  725  693  621  742  714  663  566 

0.35  1360  1340  1330  1300  1260  1330  1300  1260  1160  1320  1290  1220  1090 

0.40  1930  1930  1900  1870  1830  1900  1870  1830  1720  1900  1860  1790  1650 

0.45  2450  2450  2420  2390  2350  2420  2390  2350  2250  2420  2390  2320  2170 

0.50  2920  2920  2880  2850  2820  2880  2850  2820  2720  2880  2850  2790  2650 

0.55  3320  3320  3290  3260  3230  3290  3260  3230  3140  3290  3260  3200  3080 

0.60  3670  3670  3640  3610  3590  3640  3610  3590  3500  3640  3620  3560  3450 

0.65  3970  3980  3950  3920  3900  3950  3920  3900  3820  3950  3930  3880  3780 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.04  0.03  0.02  0.01  0.04  0.03  0.02  0.01  0.04  0.03  0.02  0.01 

0.18  2.07  1.75  1.51  0.98  0.55  1.68  1.37  0.93  0.36  1.63  1.29  0.78  0.25 

0.20  20.0  17.4  15.4  11.7  6.87  16.8  14.2  10.4  4.95  15.9  13.6  9.03  3.70 

0.25  267  245  229  193  143  241  218  180  119  238  213  167  101 

0.30  769  725  693  621  513  718  671  593  456  714  663  566  411 

0.35  1360  1300  1260  1160  1020  1290  1230  1130  938  1290  1220  1090  874 

0.40  1930  1870  1830  1720  1570  1860  1790  1680  1470  1860  1790  1650  1400 

0.45  2450  2390  2350  2250  2100  2390  2320  2210  1990  2390  2320  2170  1910 

0.50  2920  2850  2820  2720  2580  2850  2790  2680  2470  2850  2790  2650  2400 

0.55  3320  3260  3230  3140  3010  3260  3200  3110  2910  3260  3200  3080  2840 

0.60  3670  3610  3590  3500  3390  3610  3560  3480  3300  3620  3560  3450  3230 

0.65  3970  3920  3900  3820  3730  3920  3870  3800  3640  3930  3880  3780  3580 

Page 14: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-15

Table 2.E.6 – Thinning Damage Factors

Corrosion Rate 0.0254 mm/y (1 mpy), Excess Thickness Ratio minFCA t = 0.5

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.76  0.72  0.66  0.56  0.72  0.66  0.56  0.39  0.69  0.61  0.48  0.28 

0.20  11.1  10.9  10.3  9.59  8.39  10.3  9.59  8.39  6.25  10.0  9.00  7.32  4.70 

0.25  213  211  203  194  180  203  194  180  151  201  188  167  129 

0.30  677  673  655  636  606  655  636  606  539  651  625  577  488 

0.35  1240  1240  1220  1190  1150  1220  1190  1150  1060  1210  1180  1110  989 

0.40  1810  1810  1780  1750  1710  1780  1750  1710  1600  1780  1740  1670  1530 

0.45  2330  2330  2300  2270  2230  2300  2270  2230  2120  2300  2260  2190  2050 

0.50  2800  2800  2770  2730  2650  2770  2730  2650  2600  2770  2730  2670  2530 

0.55  3210  3210  3180  3140  3110  3180  3140  3110  3020  3180  3150  3090  2960 

0.60  3560  3570  3530  3500  3480  3530  3500  3480  3390  3540  3510  3450  3340 

0.65  3870  3880  3840  3820  3800  3840  3820  3800  3720  3850  3830  3780  3670 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.66  0.56  0.39  0.19  0.63  0.51  0.34  0.12  0.61  0.48  0.28  0.08 

0.20  11.1  9.59  8.39  6.25  3.48  9.24  7.72  5.49  2.42  9.00  7.32  4.70  1.75 

0.25  213  194  180  151  109  191  171  140  89.1  188  167  129  74.8 

0.30  677  636  606  539  439  629  585  513  387  625  577  488  346 

0.35  1240  1190  1150  1060  920  1180  1120  1020  840  1180  1110  989  779 

0.40  1810  1750  1710  1600  1450  1740  1670  1570  1350  1740  1670  1530  1280 

0.45  2330  2270  2230  2120  1970  2270  2200  2090  1870  2260  2190  2050  1790 

0.50  2800  2730  2650  2600  2460  2730  2670  2560  2350  2730  2670  2530  2270 

0.55  3210  3140  3110  3020  2890  3150  3080  2990  2790  3150  3090  2960  2710 

0.60  3560  3500  3480  3390  3280  3510  3450  3360  3180  3510  3450  3340  3110 

0.65  3870  3820  3800  3720  3620  3820  3770  3690  3520  3830  3780  3670  3460 

Page 15: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-16

Table 2.E.7 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.0

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.23  0.16  0.07  0.01  0.16  0.07  0.01  0.01  0.11  0.03  0.01  0.01 

0.16  6.22  4.61  3.38  1.73  0.42  3.38  1.73  0.42  0.02  2.46  0.87  0.10  0.01 

0.18  41.0  32.0  24.7  14.4  4.71  24.7  14.4  4.68  0.43  19.0  8.40  1.48  0.04 

0.20  134  109  88.8  57.7  24.2  88.8  57.7  24.0  3.82  71.6  38.0  9.92  0.55 

0.25  613  546  480  370  226  480  370  224  85.3  420  289  141  30.6 

0.30  1270  1170  1070  904  660  1070  904  655  369  983  773  491  207 

0.35  1930  1810  1700  1510  1220  1700  1510  1210  831  1600  1350  1000  583 

0.40  2520  2400  2300  2100  1800  2300  2100  1790  1380  2200  1920  1570  1090 

0.45  3030  2920  2820  2640  2360  2820  2640  2340  1930  2730  2480  2130  1650 

0.50  3460  3370  3280  3120  2860  3280  3120  2840  2470  3200  2970  2650  2210 

0.55  3840  3760  3690  3530  3300  3690  3530  3290  2950  3610  3400  3110  2730 

0.60  4150  4080  4010  3880  3690  4010  3880  3680  3390  3950  3770  3520  3200 

0.65  4420  4360  4300  4190  4030  4300  4190  4010  3770  4250  4090  3880  3610 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.07  0.01  0.01  0.01  0.05  0.01  0.01  0.01  0.03  0.01  0.01  0.01 

0.16  6.22  1.73  0.42  0.02  0.01  1.21  0.20  0.01  0.01  0.87  0.10  0.01  0.01 

0.18  41.0  14.4  4.71  0.43  0.01  10.9  2.62  0.13  0.01  8.40  1.48  0.04  0.01 

0.20  134  57.7  24.2  3.82  0.10  46.5  15.4  1.48  0.02  38.0  9.92  0.55  0.01 

0.25  613  370  226  85.3  11.5  328  176  51.8  4.19  289  141  30.6  1.65 

0.30  1270  904  660  369  122  837  541  277  70.3  773  491  207  41.6 

0.35  1930  1510  1220  831  426  1430  1100  694  310  1350  1000  583  231 

0.40  2520  2100  1800  1380  896  2030  1670  1220  734  1920  1570  1090  619 

0.45  3030  2640  2360  1930  1450  2570  2220  1780  1280  2480  2130  1650  1150 

0.50  3460  3120  2860  2470  2020  3050  2730  2320  1850  2970  2650  2210  1730 

0.55  3840  3530  3300  2950  2560  3470  3190  2820  2420  3400  3110  2730  2320 

0.60  4150  3880  3690  3390  3050  3840  3590  3270  2940  3770  3520  3200  2860 

0.65  4420  4190  4030  3770  3500  4160  3940  3670  3410  4090  3880  3610  3350 

Page 16: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-17

Table 2.E.8 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.0625

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.06  0.04  0.02  0.01  0.04  0.02  0.01  0.01  0.03  0.01  0.01  0.01 

0.16  2.82  2.04  1.46  0.70  0.15  1.46  0.70  0.15  0.01  1.04  0.33  0.03  0.01 

0.18  24.9  19.0  14.3  7.69  2.28  14.3  7.69  2.27  0.15  10.8  4.36  0.61  0.01 

0.20  96.0  76.9  61.5  38.4  14.6  61.5  38.4  14.5  1.79  48.7  24.1  5.37  0.19 

0.25  527  460  401  303  176  401  303  169  58.8  348  232  104  18.6 

0.30  1150  1050  959  798  567  959  798  563  299  873  673  413  157 

0.35  1800  1680  1570  1380  1100  1570  1380  1090  723  1470  1230  888  487 

0.40  2380  2270  2160  1970  1660  2160  1970  1650  1240  2060  1800  1390  961 

0.45  2900  2790  2650  2500  2210  2650  2500  2200  1790  2600  2350  1980  1500 

0.50  3340  3240  3150  2980  2720  3150  2980  2700  2320  3070  2830  2500  2050 

0.55  3720  3630  3550  3400  3170  3550  3400  3150  2800  3480  3270  2970  2560 

0.60  4050  3970  3900  3770  3560  3900  3770  3550  3240  3840  3650  3380  3040 

0.65  4320  4260  4200  4080  3910  4200  4080  3890  3630  4140  3980  3750  3460 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.70  0.15  0.01  0.01  0.47  0.06  0.01  0.01  0.33  0.03  0.01  0.01 

0.18  24.9  7.69  2.28  0.15  0.01  5.80  1.13  0.04  0.01  4.36  0.61  0.01  0.01 

0.20  96.0  38.4  14.6  1.79  0.03  30.2  8.80  0.61  0.01  24.1  5.4  0.19  0.01 

0.25  527  303  176  58.8  5.97  265  134  33.9  1.86  232  104  18.6  0.62 

0.30  1150  798  567  299  86.0  734  480  218  45.5  673  413  157  24.8 

0.35  1800  1380  1100  723  343  1310  978  592  239  1230  888  487  170 

0.40  2380  1970  1660  1240  770  1890  1530  1090  617  1800  1390  961  506 

0.45  2900  2500  2210  1790  1290  2430  2080  1630  1120  2350  1980  1500  993 

0.50  3340  2980  2720  2320  1850  2920  2590  2170  1680  2830  2500  2050  1550 

0.55  3720  3400  3170  2800  2390  3350  3050  2670  2240  3270  2970  2560  2130 

0.60  4050  3770  3560  3240  2880  3720  3460  3120  2760  3650  3380  3040  2670 

0.65  4320  4080  3910  3630  3330  4040  3810  3530  3230  3980  3750  3460  3170 

Page 17: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-18

Table 2.E.9 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.125

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.90  0.63  0.28  0.05  0.63  0.28  0.05  0.01  0.44  0.12  0.01  0.01 

0.18  15.1  11.2  8.37  4.39  1.11  8.37  4.39  1.11  0.05  6.14  2.20  0.25  0.01 

0.20  69.3  54.8  42.9  25.8  8.93  42.9  25.8  8.87  0.85  33.4  15.5  2.92  0.07 

0.25  453  392  338  251  140  338  251  139  42.1  291  189  78.6  11.4 

0.30  1050  953  864  710  492  864  710  489  246  782  593  350  121 

0.35  1680  1570  1460  1280  994  1460  1280  987  634  1370  1120  793  412 

0.40  2270  2150  2050  1850  1550  2050  1850  1540  1130  1950  1690  1320  833 

0.45  2790  2680  2580  2390  2090  2580  2390  2080  1670  2480  2220  1860  1370 

0.50  3240  3140  3040  2870  2590  3040  2870  2580  2190  2960  2720  2370  1910 

0.55  3620  3530  3450  3290  3050  3450  3290  3030  2670  3370  3150  2840  2420 

0.60  3950  3870  3800  3660  3450  3800  3660  3430  3110  3730  3540  3260  2900 

0.65  4240  4170  4100  3980  3800  4100  3980  3780  3510  4050  3870  3640  3330 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.28  0.05  0.01  0.01  0.18  0.02  0.01  0.01  0.12  0.01  0.01  0.01 

0.18  15.1  4.39  1.11  0.05  0.01  3.11  0.53  0.01  0.01  2.20  0.25  0.01  0.01 

0.20  69.3  25.8  8.93  0.85  0.01  19.8  5.08  0.25  0.01  15.5  2.92  0.07  0.01 

0.25  453  251  140  42.1  3.13  217  104  22.5  0.82  189  78.6  11.4  0.24 

0.30  1050  710  492  246  61.3  649  411  173  29.8  593  350  121  14.7 

0.35  1680  1280  994  634  279  1200  880  510  186  1120  793  412  127 

0.40  2270  1850  1550  1130  669  1770  1420  978  523  1690  1320  833  418 

0.45  2790  2390  2090  1670  1170  2310  1960  1500  995  2220  1860  1370  867 

0.50  3240  2870  2590  2190  1710  2800  2460  2030  1530  2720  2370  1910  1380 

0.55  3620  3290  3050  2670  2240  3230  2930  2530  2080  3150  2840  2420  1970 

0.60  3950  3660  3450  3110  2740  3610  3340  2990  2600  3540  3260  2900  2510 

0.65  4240  3980  3800  3510  3190  3940  3700  3400  3080  3870  3640  3330  3010 

Page 18: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-19

Table 2.E.10 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.25

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.17  0.12  0.05  0.01  0.12  0.05  0.01  0.01  0.08  0.02  0.01  0.01 

0.18  5.54  4.01  2.87  1.37  0.27  2.87  1.37  0.27  0.01  2.03  0.63  0.04  0.01 

0.20  36.8  28.2  21.5  12.0  3.44  21.5  12.0  3.42  0.19  16.2  6.59  0.89  0.01 

0.25  343  292  248  177  90.6  248  177  89.9  22.0  209  128  46.2  4.45 

0.30  889  799  717  576  381  717  576  379  172  628  460  258  73.7 

0.35  1500  1390  1290  1100  835  1290  1100  830  501  1190  960  647  303 

0.40  2080  1960  1860  1660  1330  1860  1660  1350  955  1750  1500  1140  685 

0.45  2600  2490  2380  2190  1890  2380  2190  1880  1460  2290  2030  1660  1170 

0.50  3060  2950  2860  2670  2390  2860  2670  2380  1970  2770  2520  2160  1680 

0.55  3450  3360  3270  3100  2850  3270  3100  2830  2460  3190  2960  2630  2190 

0.60  3800  3710  3630  3480  3250  3630  3480  3240  2900  3560  3350  3060  2670 

0.65  4090  4010  3950  3820  3610  3950  3820  3600  3300  3890  3700  3440  3100 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.05  0.01  0.01  0.01  0.03  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.18  5.54  1.37  0.27  0.01  0.01  0.91  0.11  0.01  0.01  0.63  0.04  0.01  0.01 

0.20  36.8  12.0  3.4  0.19  0.01  8.78  1.75  0.04  0.01  6.59  0.89  0.01  0.01 

0.25  343  177  90.6  22.0  0.89  150  64.2  10.3  0.17  128  46.2  4.45  0.03 

0.30  889  576  381  172  32.3  521  311  114  13.2  460  258  73.7  5.45 

0.35  1500  1100  835  501  191  1030  729  390  117  960  647  303  72.7 

0.40  2080  1660  1330  955  517  1580  1230  808  385  1500  1140  685  294 

0.45  2600  2190  1890  1460  967  2110  1760  1300  801  2030  1660  1170  678 

0.50  3060  2670  2390  1970  1480  2600  2260  1810  1300  2520  2160  1680  1170 

0.55  3450  3100  2850  2460  1990  3040  2720  2310  1830  2960  2630  2190  1710 

0.60  3800  3480  3250  2900  2490  3430  3140  2760  2350  3350  3060  2670  2240 

0.65  4090  3820  3610  3300  2950  3770  3510  3180  2830  3700  3440  3100  2750 

Page 19: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-20

Table 2.E.11 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.375

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.03  0.02  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  1.45  1.01  0.44  0.07  1.01  0.44  0.07  0.01  0.69  0.18  0.01  0.01 

0.20  20.0  14.9  11.1  5.74  1.39  11.1  5.74  1.38  0.05  8.10  2.92  0.28  0.01 

0.25  267  224  187  129  61.2  187  129  60.8  12.0  155  90.3  28.5  1.82 

0.30  769  685  609  480  305  609  480  303  124  539  385  198  47.1 

0.35  1360  1250  1150  975  696  1150  975  713  408  1060  837  543  231 

0.40  1930  1820  1710  1510  1220  1710  1510  1210  825  1610  1350  1000  572 

0.45  2450  2340  2230  2040  1730  2230  2040  1720  1310  2130  1870  1500  1020 

0.50  2920  2810  2710  2520  2230  2710  2520  2220  1800  2610  2360  2000  1510 

0.55  3320  3220  3130  2950  2690  3130  2950  2670  2280  3040  2810  2470  2010 

0.60  3670  3580  3500  3340  3100  3500  3340  3080  2730  3420  3200  2900  2480 

0.65  3970  3890  3820  3680  3470  3820  3680  3450  3130  3750  3560  3280  2920 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.44  0.07  0.01  0.01  0.28  0.02  0.01  0.01  0.18  0.01  0.01  0.01 

0.20  20.0  5.74  1.39  0.05  0.01  3.98  0.63  0.01  0.01  2.92  0.28  0.01  0.01 

0.25  267  129  61.2  12.0  0.26  108  41.5  4.93  0.04  90.3  28.5  1.82  0.01 

0.30  769  480  305  124  17.8  430  243  77.9  6.12  385  198  47.1  2.12 

0.35  1360  975  696  408  135  905  619  308  76.1  837  543  231  43.4 

0.40  1930  1510  1220  825  412  1430  1090  685  294  1350  1000  572  213 

0.45  2450  2040  1730  1310  821  1960  1600  1150  662  1870  1500  1020  545 

0.50  2920  2520  2230  1800  1300  2450  2100  1640  1130  2360  2000  1510  996 

0.55  3320  2950  2690  2280  1810  2890  2560  2130  1640  2810  2470  2010  1510 

0.60  3670  3340  3100  2730  2300  3280  2980  2590  2140  3200  2900  2480  2030 

0.65  3970  3680  3470  3130  2760  3630  3360  3010  2630  3560  3280  2920  2540 

Page 20: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-21

Table 2.E.12 – Thinning Damage Factors

Corrosion Rate 0.076 mm/y (3 mpy), Excess Thickness Ratio minFCA t = 0.5

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.54  0.37  0.15  0.02  0.37  0.15  0.02  0.01  0.24  0.05  0.01  0.01 

0.20  11.1  8.13  5.88  2.86  0.58  5.88  2.86  0.58  0.01  4.19  1.34  0.09  0.01 

0.25  213  177  145  97.3  42.9  145  97.3  42.6  6.79  119  65.8  18.2  0.78 

0.30  677  598  527  409  250  527  409  248  93.2  463  322  156  31.2 

0.35  1240  1140  1040  875  630  1040  875  626  340  954  743  465  181 

0.40  1810  1700  1590  1400  1110  1590  1400  1100  726  1490  1240  894  485 

0.45  2330  2220  2110  1910  1610  2110  1910  1600  1190  2010  1750  1380  903 

0.50  2800  2690  2590  2400  2100  2590  2400  2090  1670  2490  2230  1870  1380 

0.55  3210  3100  3010  2830  2560  3010  2830  2540  2150  2920  2680  2330  1860 

0.60  3560  3470  3380  3220  2970  3380  3220  2960  2590  3310  3080  2760  2330 

0.65  3870  3790  3710  3570  3340  3710  3570  3330  3000  3640  3440  3150  2770 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.15  0.02  0.01  0.01  0.09  0.01  0.01  0.01  0.05  0.01  0.01  0.01 

0.20  11.1  2.86  0.58  0.01  0.01  1.93  0.24  0.01  0.01  1.34  0.09  0.01  0.01 

0.25  213  97.3  42.9  6.79  0.08  79.6  27.8  2.47  0.01  65.8  18.2  0.78  0.01 

0.30  677  409  250  93.2  10.2  362  196  55.2  2.95  322  156  31.2  0.85 

0.35  1240  875  630  340  99.1  807  523  249  51.5  743  465  181  26.8 

0.40  1810  1400  1110  726  337  1320  986  592  230  1240  894  485  160 

0.45  2330  1910  1610  1190  697  1830  1480  1030  559  1750  1380  903  448 

0.50  2800  2400  2100  1670  1170  2320  1960  1510  994  2230  1870  1380  864 

0.55  3210  2830  2560  2150  1660  2760  2430  1990  1480  2680  2330  1860  1350 

0.60  3560  3220  2970  2590  2140  3160  2850  2440  1980  3080  2760  2330  1860 

0.65  3870  3570  3340  3000  2600  3510  3230  2870  2460  3440  3150  2770  2360 

Page 21: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-22

Table 2.E.13 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.0

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.12  0.04  0.01  0.01  0.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  2.60  1.03  0.13  0.01  1.03  0.13  0.01  0.01  0.38  0.02  0.01  0.01 

0.18  41.0  20.1  9.58  1.89  0.07  9.58  1.89  0.07  0.01  4.33  0.35  0.01  0.01 

0.20  134  75.5  42.0  12.0  0.86  42.0  12.0  0.86  0.01  22.7  3.23  0.07  0.01 

0.25  613  424  308  155  38.7  308  155  38.7  2.63  217  77.3  9.47  0.25 

0.30  1270  1010  778  523  236  778  523  236  54.3  643  347  110  13.3 

0.35  1930  1630  1390  1040  630  1390  1040  630  268  1200  800  402  122 

0.40  2520  2220  1980  1610  1150  1980  1610  1150  676  1780  1280  865  427 

0.45  3030  2760  2510  2170  1710  2510  2170  1710  1210  2330  1900  1420  918 

0.50  3460  3220  3010  2680  2260  3010  2680  2260  1790  2830  2440  1990  1510 

0.55  3840  3620  3430  3150  2770  3430  3150  2770  2370  3280  2930  2530  2130 

0.60  4150  3960  3800  3550  3230  3800  3550  3230  2900  3670  3370  3030  2720 

0.65  4420  4260  4120  3910  3640  4120  3910  3640  3380  4010  3750  3480  3260 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  0.13  0.01  0.01  0.01  0.05  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.18  41.0  1.89  0.07  0.01  0.01  0.80  0.01  0.01  0.01  0.35  0.01  0.01  0.01 

0.20  134  12.0  0.86  0.01  0.01  6.22  0.23  0.01  0.01  3.23  0.07  0.01  0.01 

0.25  613  155  38.7  2.63  0.04  109  19.1  0.74  0.01  77.3  9.47  0.25  0.01 

0.30  1270  523  236  54.3  3.93  426  161  26.2  1.37  347  110  13.3  0.55 

0.35  1930  1040  630  268  59.4  913  501  179  30.4  800  402  122  16.6 

0.40  2520  1610  1150  676  282  1470  990  534  190  1280  865  427  132 

0.45  3030  2170  1710  1210  721  2030  1550  1050  572  1900  1420  918  464 

0.50  3460  2680  2260  1790  1310  2560  2110  1640  1150  2440  1990  1510  1020 

0.55  3840  3150  2770  2370  1970  3040  2640  2240  1830  2930  2530  2130  1720 

0.60  4150  3550  3230  2900  2610  3460  3120  2800  2520  3370  3030  2720  2450 

0.65  4420  3910  3640  3380  3210  3830  3550  3310  3160  3750  3480  3260  3140 

Page 22: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-23

Table 2.E.14 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.0625

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  1.09  0.40  0.04  0.01  0.40  0.04  0.01  0.01  0.13  0.01  0.01  0.01 

0.18  24.9  11.4  5.03  0.81  0.02  5.03  0.81  0.02  0.01  2.07  0.12  0.01  0.01 

0.20  96.0  51.4  27.0  6.66  0.32  27.0  6.66  0.32  0.01  13.6  1.49  0.02  0.01 

0.25  527  361  248  116  24.3  248  116  24.3  1.07  169  53.5  4.78  0.07 

0.30  1150  896  701  419  182  701  419  182  33.7  552  280  75.6  6.49 

0.35  1800  1500  1260  925  532  1260  925  532  202  1080  692  321  80.8 

0.40  2380  2090  1840  1480  1020  1840  1480  1020  560  1640  1210  740  329 

0.45  2900  2620  2380  2020  1560  2380  2020  1560  1060  2190  1760  1260  768 

0.50  3340  3090  2870  2540  2100  2870  2540  2100  1620  2690  2290  1820  1330 

0.55  3720  3500  3300  3000  2610  3300  3000  2610  2180  3140  2780  2360  1930 

0.60  4050  3850  3680  3420  3070  3680  3420  3070  2720  3540  3220  2860  2520 

0.65  4320  4150  4000  3780  3490  4000  3780  3490  3200  3880  3610  3320  3060 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  24.9  0.81  0.02  0.01  0.01  0.31  0.01  0.01  0.01  0.12  0.01  0.01  0.01 

0.20  96.0  6.66  0.32  0.01  0.01  3.13  0.07  0.01  0.01  1.49  0.02  0.01  0.01 

0.25  527  116  24.3  1.07  0.01  79.0  10.8  0.24  0.01  53.5  4.78  0.07  0.01 

0.30  1150  419  182  33.7  1.56  351  118  14.4  0.46  280  75.6  6.49  0.16 

0.35  1800  925  532  202  34.7  764  400  127  15.8  692  321  80.8  7.75 

0.40  2380  1480  1020  560  203  1340  862  427  127  1210  740  329  82.5 

0.45  2900  2020  1560  1060  578  1880  1390  896  439  1760  1260  768  342 

0.50  3340  2540  2100  1620  1120  2410  1940  1460  957  2290  1820  1330  829 

0.55  3720  3000  2610  2180  1750  2890  2470  2040  1600  2780  2360  1930  1480 

0.60  4050  3420  3070  2720  2390  3320  2960  2610  2280  3220  2860  2520  2190 

0.65  4320  3780  3490  3200  2990  3690  3390  3130  2930  3610  3320  3060  2880 

Page 23: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-24

Table 2.E.15 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.125

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.46  0.15  0.01  0.01  0.15  0.01  0.01  0.01  0.04  0.01  0.01  0.01 

0.18  15.1  6.51  2.67  0.35  0.01  2.67  0.35  0.01  0.01  1.00  0.04  0.01  0.01 

0.20  69.3  35.4  17.6  3.72  0.12  17.6  3.72  0.12  0.01  8.25  0.69  0.01  0.01 

0.25  453  303  202  88.5  15.5  202  88.5  15.5  0.44  134  37.5  2.41  0.02 

0.30  1050  804  619  375  142  619  375  142  21.1  478  229  53.7  3.18 

0.35  1680  1390  1160  829  453  1160  829  453  154  912  605  259  54.0 

0.40  2270  1970  1720  1360  907  1720  1360  907  468  1520  1100  640  257 

0.45  2790  2500  2260  1900  1430  2260  1900  1430  930  2060  1630  1130  648 

0.50  3240  2980  2750  2410  1960  2750  2410  1960  1470  2570  2150  1670  1170 

0.55  3620  3390  3190  2880  2470  3190  2880  2470  2020  3020  2640  2210  1760 

0.60  3950  3750  3570  3300  2940  3570  3300  2940  2560  3430  3090  2710  2340 

0.65  4240  4060  3900  3670  3360  3900  3670  3360  3050  3780  3490  3170  2890 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.04  0.01  0.01  0.01  0.04  0.01  0.01  0.01  0.04  0.04  0.01  0.01  0.01 

0.20  0.69  0.01  0.01  0.01  0.69  0.01  0.01  0.01  0.69  0.69  0.01  0.01  0.01 

0.25  37.5  2.41  0.02  0.01  37.5  2.41  0.02  0.01  37.5  37.5  2.41  0.02  0.01 

0.30  229  53.7  3.18  0.05  229  53.7  3.18  0.05  229  229  53.7  3.18  0.05 

0.35  605  259  54.0  3.63  605  259  54.0  3.63  605  605  259  54.0  3.63 

0.40  1100  640  257  51.9  1100  640  257  51.9  1100  1100  640  257  51.9 

0.45  1630  1130  648  254  1630  1130  648  254  1630  1630  1130  648  254 

0.50  2150  1670  1170  678  2150  1670  1170  678  2150  2150  1670  1170  678 

0.55  2640  2210  1760  1280  2640  2210  1760  1280  2640  2640  2210  1760  1280 

0.60  3090  2710  2340  1970  3090  2710  2340  1970  3090  3090  2710  2340  1970 

0.65  3490  3170  2890  2660  3490  3170  2890  2660  3490  3490  3170  2890  2660 

Page 24: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-25

Table 2.E.16 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.25

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.08  0.02  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  2.14  0.76  0.07  0.01  0.76  0.07  0.01  0.01  0.24  0.01  0.01  0.01 

0.20  36.8  17.1  7.64  1.19  0.02  7.64  1.19  0.02  0.01  3.14  0.15  0.01  0.01 

0.25  343  219  138  53.3  6.50  138  53.3  6.50  0.08  86.1  19.1  0.64  0.01 

0.30  889  662  494  280  89.7  494  280  89.7  8.59  370  158  27.4  0.78 

0.35  1500  1220  992  681  339  992  681  339  92.5  817  475  174  24.8 

0.40  2080  1780  1540  1180  740  1540  1180  740  337  1340  921  486  160 

0.45  2600  2310  2060  1700  1230  2060  1700  1230  738  1860  1430  935  473 

0.50  3060  2790  2550  2200  1740  2550  2200  1740  1240  2360  1940  1440  934 

0.55  3450  3210  2990  2670  2240  2990  2670  2240  1770  2820  2420  1960  1480 

0.60  3800  3580  3380  3090  2710  3380  3090  2710  2290  3230  2870  2470  2050 

0.65  4090  3900  3730  3470  3140  3730  3470  3140  2790  3590  3280  2930  2600 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  0.07  0.01  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  36.8  1.19  0.02  0.01  0.01  0.43  0.01  0.01  0.01  0.15  0.01  0.01  0.01 

0.25  343  53.3  6.50  0.08  0.01  32.1  2.05  0.01  0.01  19.1  0.64  0.01  0.01 

0.30  889  280  89.7  8.59  0.10  211  49.7  2.47  0.02  158  27.4  0.78  0.01 

0.35  1500  681  339  92.5  7.19  569  242  47.4  2.29  475  174  24.8  0.81 

0.40  2080  1180  740  337  79.1  1040  599  231  39.9  921  486  160  21.1 

0.45  2600  1700  1230  738  314  1560  1070  588  210  1430  935  473  144 

0.50  3060  2200  1740  1240  732  2060  1580  1070  577  1940  1440  934  462 

0.55  3450  2670  2240  1770  1280  2540  2090  1610  1110  2420  1960  1480  977 

0.60  3800  3090  2710  2290  1880  2980  2570  2160  1730  2870  2470  2050  1610 

0.65  4090  3470  3140  2790  2460  3370  3020  2680  2370  3280  2930  2600  2290 

Page 25: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-26

Table 2.E.17 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.375

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.72  0.23  0.01  0.01  0.23  0.01  0.01  0.01  0.06  0.01  0.01  0.01 

0.20  20.0  8.58  3.45  0.40  0.01  3.45  0.40  0.01  0.01  1.24  0.04  0.01  0.01 

0.25  267  163  98.5  33.5  2.86  98.5  33.5  2.86  0.01  57.9  10.3  0.18  0.01 

0.30  769  558  402  213  59.1  402  213  59.1  3.63  295  113  14.6  0.20 

0.35  1360  1080  825  574  263  825  574  263  57.8  701  384  122  11.8 

0.40  1930  1630  1390  1040  620  1390  1040  620  251  1190  792  388  104 

0.45  2450  2160  1910  1540  1070  1910  1540  1070  602  1710  1270  790  356 

0.50  2920  2640  2400  2040  1570  2400  2040  1570  1060  2200  1770  1270  765 

0.55  3320  3060  2840  2510  2060  2840  2510  2060  1570  2660  2250  1770  1270 

0.60  3670  3440  3240  2930  2530  3240  2930  2530  2090  3070  2700  2270  1820 

0.65  3970  3770  3590  3320  2960  3590  3320  2960  2580  3440  3110  2740  2370 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  20.0  0.40  0.01  0.01  0.01  0.12  0.01  0.01  0.01  0.04  0.01  0.01  0.01 

0.25  267  33.5  2.86  0.01  0.01  18.7  0.72  0.01  0.01  10.3  0.18  0.01  0.01 

0.30  769  213  59.1  3.63  0.02  157  29.6  0.80  0.01  113  14.6  0.20  0.01 

0.35  1360  574  263  57.8  2.63  470  179  25.9  0.66  384  122  11.8  0.19 

0.40  1930  1040  620  251  44.2  907  488  159  19.3  792  388  104  8.86 

0.45  2450  1540  1070  602  217  1400  916  461  134  1270  790  356  84.2 

0.50  2920  2040  1570  1060  570  1900  1400  897  426  1770  1270  765  325 

0.55  3320  2510  2060  1570  1060  2370  1900  1410  895  2250  1770  1270  763 

0.60  3670  2930  2530  2090  1630  2810  2390  1940  1470  2700  2270  1820  1350 

0.65  3970  3320  2960  2580  2220  3210  2840  2460  2090  3110  2740  2370  1990 

Page 26: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-27

Table 2.E.18 – Thinning Damage Factors

Corrosion Rate 0.127 mm/y (5 mpy), Excess Thickness Ratio minFCA t = 0.5

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.25  0.07  0.01  0.01  0.07  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.20  11.1  4.4  1.62  0.14  0.01  1.62  0.14  0.01  0.01  0.52  0.01  0.01  0.01 

0.25  213  125  72.3  21.9  1.31  72.3  21.9  1.31  0.01  40.3  5.75  0.05  0.01 

0.30  677  480  341  172  40.4  341  172  40.4  1.60  241  84.2  8.09  0.05 

0.35  1240  978  772  494  209  772  494  209  36.9  614  319  87.9  5.84 

0.40  1810  1520  1280  932  531  1280  932  531  193  1080  695  315  69.3 

0.45  2330  2040  1790  1420  958  1790  1420  958  501  1580  1150  681  275 

0.50  2800  2510  2270  1910  1430  2270  1910  1430  928  2070  1630  1130  639 

0.55  3210  2940  2720  2370  1920  2720  2370  1920  1420  2530  2110  1620  1110 

0.60  3560  3320  3110  2800  2380  3110  2800  2380  1920  2950  2560  2110  1640 

0.65  3870  3660  3470  3190  2810  3470  3190  2810  2410  3320  2970  2580  2180 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  11.1  0.14  0.01  0.01  0.01  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  213  21.9  1.31  0.01  0.01  11.3  0.26  0.01  0.01  5.75  0.05  0.01  0.01 

0.30  677  172  40.4  1.60  0.01  121  18.4  0.27  0.01  84.2  8.09  0.05  0.01 

0.35  1240  494  209  36.9  1.00  397  135  14.7  0.20  319  87.9  5.84  0.05 

0.40  1810  932  531  193  25.6  805  407  115  9.72  695  315  69.3  3.88 

0.45  2330  1420  958  501  155  1240  803  370  87.8  1150  681  275  51.0 

0.50  2800  1910  1430  928  454  1770  1270  767  323  1630  1130  639  231 

0.55  3210  2370  1920  1420  904  2240  1760  1250  736  2110  1620  1110  609 

0.60  3560  2800  2380  1920  1440  2680  2230  1770  1280  2560  2110  1640  1140 

0.65  3870  3190  2810  2410  2020  3080  2680  2290  1850  2970  2580  2180  1760 

Page 27: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-28

Table 2.E.19 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.0

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  0.13  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  41.0  1.89  0.07  0.01  0.01  0.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  134  12.0  0.86  0.01  0.01  0.86  0.01  0.01  0.01  0.07  0.01  0.01  0.01 

0.25  613  155  38.7  2.53  0.04  38.7  2.53  0.04  0.01  9.64  0.24  0.01  0.01 

0.30  1270  523  236  53.5  3.99  236  53.5  3.99  0.15  112  13.0  0.54  0.02 

0.35  1930  1040  630  268  60.1  630  268  60.1  6.50  405  119  16.3  1.41 

0.40  2520  1610  1150  677  285  1150  677  285  73.4  869  420  130  25.4 

0.45  3030  2170  1710  1210  728  1710  1210  728  330  1420  904  458  169 

0.50  3460  2680  2260  1800  1320  2260  1800  1320  850  1990  1490  1010  572 

0.55  3840  3150  2770  2380  1980  2770  2380  1980  1570  2540  2110  1710  1270 

0.60  4150  3550  3230  2910  2630  3230  2910  2630  2370  3040  2700  2430  2140 

0.65  4420  3910  3640  3400  3220  3640  3400  3220  3150  3490  3230  3120  3050 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  41.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  134  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  613  2.53  0.04  0.01  0.01  0.74  0.01  0.01  0.01  0.24  0.01  0.01  0.01 

0.30  1270  54  3.99  0.15  0.01  26.5  1.35  0.05  0.01  13.0  0.54  0.02  0.01 

0.35  1930  268  60.1  6.50  0.52  181  30.4  2.69  0.25  119  16.3  1.41  0.13 

0.40  2520  677  285  73.4  12.3  538  192  39.7  7.01  420  130  25.4  4.19 

0.45  3030  1210  728  330  105  1060  578  223  72.1  904  458  169  50.8 

0.50  3460  1800  1320  850  434  1650  1160  669  346  1490  1010  572  280 

0.55  3840  2380  1980  1570  1100  2250  1850  1370  979  2110  1710  1270  878 

0.60  4150  2910  2630  2370  2030  2820  2540  2210  1940  2700  2430  2140  1860 

0.65  4420  3400  3220  3150  3030  3330  3180  3050  3020  3230  3120  3050  3010 

Page 28: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-29

Table 2.E.20 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.0625

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  24.9  0.81  0.02  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  96.0  6.66  0.32  0.01  0.01  0.32  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.25  527  116  24.3  1.03  0.01  24.3  1.03  0.01  0.01  4.91  0.07  0.01  0.01 

0.30  1150  419  182  33.0  1.59  182  33.0  1.59  0.03  77.4  6.34  0.16  0.01 

0.35  1800  925  532  201  35.1  532  201  35.1  2.59  323  79.1  7.58  0.45 

0.40  2380  1480  1020  560  202  1020  560  202  40.9  744  323  81.1  11.8 

0.45  2900  2020  1560  1060  583  1560  1060  583  226  1270  755  337  102 

0.50  3340  2540  2100  1620  1130  2100  1620  1130  659  1820  1310  821  406 

0.55  3720  3000  2610  2190  1760  2610  2190  1760  1310  2370  1910  1470  1000 

0.60  4050  3420  3070  2730  2400  3070  2730  2400  2080  2870  2490  2170  1810 

0.65  4320  3780  3490  3220  3000  3490  3220  3000  2860  3330  3040  2870  2700 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  24.9  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  96.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  527  1.03  0.01  0.01  0.01  0.25  0.01  0.01  0.01  0.07  0.01  0.01  0.01 

0.30  1150  33.0  1.59  0.03  0.01  14.5  0.45  0.01  0.01  6.34  0.16  0.01  0.01 

0.35  1800  201  35.1  2.59  0.14  126  15.7  0.94  0.06  79.1  7.58  0.45  0.03 

0.40  2380  560  202  40.9  5.05  430  128  20.0  2.61  323  81.1  11.8  1.42 

0.45  2900  1060  583  226  57.5  903  444  142  36.5  755  337  102  23.9 

0.50  3340  1620  1130  659  288  1470  967  494  217  1310  821  406  167 

0.55  3720  2190  1760  1310  830  2060  1610  1110  711  1910  1470  1000  615 

0.60  4050  2730  2400  2080  1670  2620  2300  1900  1560  2490  2170  1810  1460 

0.65  4320  3220  3000  2860  2650  3140  2950  2730  2600  3040  2870  2700  2560 

Page 29: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-30

Table 2.E.21 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.125

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  15.1  0.35  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  69.3  3.72  0.12  0.01  0.01  0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  453  88.5  15.5  0.42  0.01  15.5  0.42  0.01  0.01  2.50  0.02  0.01  0.01 

0.30  1050  375  142  20.7  0.63  142  20.7  0.63  0.01  54.5  3.10  0.04  0.01 

0.35  1680  829  453  153  20.6  453  153  20.6  1.03  261  52.8  3.54  0.14 

0.40  2270  1360  907  468  148  907  468  148  23.0  643  252  51.0  5.56 

0.45  2790  1900  1430  933  472  1430  933  472  156  1140  637  250  61.7 

0.50  3240  2410  1960  1480  975  1960  1480  975  514  1680  1160  661  290 

0.55  3620  2880  2470  2030  1580  2470  2030  1580  1100  2220  1730  1270  793 

0.60  3950  3300  2940  2570  2210  2940  2570  2210  1840  2720  2310  1950  1540 

0.65  4240  3670  3360  3060  2810  3360  3060  2810  2600  3180  2860  2640  2400 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  15.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  69.3  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  453  0.42  0.01  0.01  0.01  0.08  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.30  1050  20.7  0.63  0.01  0.01  8.01  0.15  0.01  0.01  3.10  0.04  0.01  0.01 

0.35  1680  153  20.6  1.03  0.04  91.2  8.17  0.33  0.01  52.8  3.54  0.14  0.01 

0.40  2270  468  148  23.0  2.10  347  85.7  10.2  0.98  252  51.0  5.56  0.49 

0.45  2790  933  472  156  31.8  778  344  91.5  18.6  637  250  61.7  11.3 

0.50  3240  1480  975  514  192  1320  811  367  137  1160  661  290  99.6 

0.55  3620  2030  1580  1100  629  1890  1420  903  518  1730  1270  793  431 

0.60  3950  2570  2210  1840  1380  2450  2090  1640  1250  2310  1950  1540  1140 

0.65  4240  3060  2810  2600  2320  2970  2740  2450  2240  2860  2640  2400  2170 

Page 30: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-31

Table 2.E.22 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.25

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  0.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  36.8  1.19  0.02  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  343  53.3  6.50  0.07  0.01  6.50  0.07  0.01  0.01  0.67  0.01  0.01  0.01 

0.30  889  280  89.7  8.30  0.10  89.7  8.30  0.10  0.01  27.9  0.76  0.01  0.01 

0.35  1500  681  339  91.5  7.30  339  91.5  7.30  0.17  176  24.2  0.79  0.02 

0.40  2080  1180  740  337  80.1  740  337  80.1  7.45  494  157  20.6  1.27 

0.45  2600  1700  1230  740  317  1230  740  317  76.4  940  465  141  23.5 

0.50  3060  2200  1740  1240  739  1740  1240  739  320  1450  922  457  152 

0.55  3450  2670  2240  1780  1290  2240  1780  1290  795  1970  1460  967  509 

0.60  3800  3090  2710  2310  1890  2710  2310  1890  1450  2470  2020  1600  1130 

0.65  4090  3470  3140  2800  2490  3140  2800  2490  2190  2940  2570  2270  1920 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  36.8  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  343  0.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  889  8.30  0.10  0.01  0.01  2.50  0.02  0.01  0.01  0.76  0.01  0.01  0.01 

0.35  1500  91.5  7.30  0.17  0.01  47.9  2.25  0.04  0.01  24.2  0.79  0.02  0.01 

0.40  2080  337  80.1  7.45  0.38  233  39.9  2.72  0.15  157  20.6  1.27  0.06 

0.45  2600  740  317  76.4  10.0  593  211  39.0  5.07  465  141  23.5  2.67 

0.50  3060  1240  739  320  88.1  1080  582  208  56.2  922  457  152  36.6 

0.55  3450  1780  1290  795  368  1620  1120  610  280  1460  967  509  216 

0.60  3800  2310  1890  1450  947  2170  1750  1240  818  2020  1600  1130  710 

0.65  4090  2800  2490  2190  1780  2700  2390  2000  1670  2570  2270  1920  1570 

Page 31: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-32

Table 2.E.23 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.375

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  20.0  0.40  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  267  33.5  2.86  0.01  0.01  2.86  0.01  0.01  0.01  0.19  0.01  0.01  0.01 

0.30  769  213  59.1  3.47  0.02  59.1  3.47  0.02  0.01  14.9  0.19  0.01  0.01 

0.35  1360  574  263  56.9  2.67  263  56.9  2.67  0.03  123  11.5  0.18  0.01 

0.40  1930  1040  620  250  44.8  620  250  44.8  2.52  391  102  8.64  0.31 

0.45  2450  1540  1070  602  220  1070  602  220  38.8  794  349  82.7  9.35 

0.50  2920  2040  1570  1060  572  1570  1060  572  205  1280  753  321  82.8 

0.55  3320  2510  2060  1580  1070  2060  1580  1070  587  1780  1260  755  336 

0.60  3670  2930  2530  2100  1650  2530  2100  1650  1170  2280  1800  1330  842 

0.65  3970  3320  2960  2590  2230  2960  2590  2230  1860  2750  2340  1980  1560 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  20.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  267  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  769  3.47  0.02  0.01  0.01  0.81  0.01  0.01  0.01  0.19  0.01  0.01  0.01 

0.35  1360  56.9  2.67  0.03  0.01  26.2  0.64  0.01  0.01  11.5  0.18  0.01  0.01 

0.40  1930  250  44.8  2.52  0.07  162  19.2  0.77  0.02  102  8.64  0.31  0.01 

0.45  2450  602  220  38.8  3.36  465  134  17.3  1.48  349  82.7  9.35  0.68 

0.50  2920  1060  572  205  42.2  904  431  122  24.2  753  321  82.8  14.2 

0.55  3320  1580  1070  587  222  1420  904  423  157  1260  755  336  112 

0.60  3670  2100  1650  1170  665  1960  1490  957  545  1800  1330  842  449 

0.65  3970  2590  2230  1860  1390  2480  2110  1660  1230  2340  1980  1560  1140 

Page 32: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-33

Table 2.E.24 – Thinning Damage Factors

Corrosion Rate 0.254 mm/y (10 mpy), Excess Thickness Ratio minFCA t = 0.5

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  11.1  0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  213  21.9  1.31  0.01  0.01  1.31  0.01  0.01  0.01  0.05  0.01  0.01  0.01 

0.30  677  172  40.4  1.51  0.01  40.4  1.51  0.01  0.01  8.33  0.05  0.01  0.01 

0.35  1240  494  209  36.7  1.02  209  36.7  1.02  0.01  89.1  5.70  0.04  0.01 

0.40  1810  932  531  191  26.0  531  191  26.0  0.89  317  67.8  3.77  0.08 

0.45  2330  1420  958  502  157  958  502  157  20.5  685  270  50.0  3.92 

0.50  2800  1910  1430  931  458  1430  931  458  136  1140  628  231  46.8 

0.55  3210  2370  1920  1420  912  1920  1420  912  444  1630  1100  602  228 

0.60  3560  2800  2380  1930  1460  2380  1930  1460  957  2120  1620  1130  642 

0.65  3870  3190  2810  2430  2030  2810  2430  2030  1610  2570  2150  1750  1280 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  11.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  213  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  677  1.51  0.01  0.01  0.01  0.27  0.01  0.01  0.01  0.05  0.01  0.01  0.01 

0.35  1240  36.7  1.02  0.01  0.01  14.8  0.19  0.01  0.01  5.70  0.04  0.01  0.01 

0.40  1810  191  26.0  0.89  0.02  116  9.40  0.23  0.01  67.8  3.77  0.08  0.01 

0.45  2330  502  157  20.5  1.20  373  88.2  8.07  0.46  270  50.0  3.92  0.19 

0.50  2800  931  458  136  21.1  773  326  74.2  11.0  628  231  46.8  5.82 

0.55  3210  1420  912  444  138  1260  744  297  90.8  1100  602  228  60.3 

0.60  3560  1930  1460  957  478  1780  1290  754  373  1620  1130  642  292 

0.65  3870  2430  2030  1610  1100  2300  1890  1400  962  2150  1750  1280  845 

Page 33: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-34

Table 2.E.25 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.0

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  41.0 0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  134  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  613  2.50  0.04  0.01  0.01  0.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1270  52.8 3.75  0.14  0.01  3.75  0.14  0.01  0.01  0.55  0.02  0.01  0.01 

0.35  1930  264  57.5 6.17  0.52  57.5 6.17  0.52  0.05  16.4 1.51  0.13  0.01 

0.40  2520  667  276  70.2 12.2 276  70.2 12.2 2.04  131  26.9 4.27  0.75 

0.45  3030  1200  709  318  105  709  318  105  30.7 459  177  51.4 14.9

0.50  3460  1780  1300  825  434  1300  825  434  206  1010  594  283  131 

0.55  3840  2350  1950  1530  1100  1950  1530  1100  746  1700  1310  881  586 

0.60  4150  2880  2590  2330  2030  2590  2330  2030  1740  2430  2200  1860  1580 

0.65  4420  3360  3180  3100  3040  3180  3100  3040  2990  3120  3100  3010  2970 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.32  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  6.22  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  41.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  134  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  613  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1270  0.14  0.01  0.01  0.01  0.05  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.35  1930  6.17  0.52  0.05  0.01  2.86  0.24  0.02  0.01  1.51  0.13  0.01  0.01 

0.40  2520  70.2  12.2  2.04  0.39  42.0  6.85  1.15  0.25  26.9  4.27  0.75  0.18 

0.45  3030  318  105  30.7  9.25  234  71.1  20.4  6.66  177  51.4  14.9  5.14 

0.50  3460  825  434  206  95.9  696  344  160  77.2  594  283  131  64.9 

0.55  3840  1530  1100  746  497  1410  976  652  442  1310  881  586  401 

0.60  4150  2330  2030  1740  1480  2260  1940  1650  1410  2200  1860  1580  1360 

0.65  4420  3100  3040  2990  2950  3100  3020  2980  2940  3100  3010  2970  2930 

Page 34: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-35

Table 2.E.26 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.0625

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  24.9  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  96.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  527  1.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1150  32.7  1.48  0.03  0.01  1.48  0.03  0.01  0.01  0.16  0.01  0.01  0.01 

0.35  1800  198  33.4  2.45  0.14  33.4  2.45  0.14  0.01  7.67  0.48  0.03  0.01 

0.40  2380  552  198  39.1  5.01  198  39.1  5.01  0.60  81.5  12.6  1.45  0.18 

0.45  2900  1050  567  218  57.4  567  218  57.4  12.9  338  107  24.2  5.32 

0.50  3340  1600  1110  638  288  1110  638  288  113  821  423  168  63.0 

0.55  3720  2170  1730  1280  830  1730  1280  830  494  1470  1030  618  356 

0.60  4050  2700  2370  2040  1650  2370  2040  1650  1320  2170  1860  1460  1140 

0.65  4320  3190  2970  2810  2650  2970  2810  2650  2500  2860  2760  2560  2410 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  2.82  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  24.9  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  96.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  527  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1150  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1800  2.45  0.14  0.01  0.01  1.00  0.06  0.01  0.01  0.48  0.03  0.01  0.01 

0.40  2380  39.1  5.01  0.60  0.08  21.3  2.54  0.31  0.05  12.6  1.45  0.18  0.03 

0.45  2900  218  57.4  12.9  2.95  150  35.9  7.86  1.95  107  24.2  5.32  1.41 

0.50  3340  638  288  113  42.4  515  215  81.5  32.0  423  168  63.0  25.5 

0.55  3720  1280  830  494  283  1150  708  412  240  1030  618  356  210 

0.60  4050  2040  1650  1320  1020  1950  1550  1220  951  1860  1460  1140  894 

0.65  4320  2810  2650  2500  2340  2790  2580  2450  2300  2760  2560  2410  2260 

Page 35: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-36

Table 2.E.27 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.125

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  15.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  69.3  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  453  0.41  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1050  20.4  0.59  0.01  0.01  0.59  0.01  0.01  0.01  0.05  0.01  0.01  0.01 

0.35  1680  151  19.6  0.98  0.04  19.6  0.98  0.04  0.01  3.60  0.15  0.01  0.01 

0.40  2270  461  143  21.9  2.08  143  21.9  2.08  0.18  51.3  5.94  0.50  0.04 

0.45  2790  920  458  150  31.6  458  150  31.6  5.50  251  65.1  11.5  1.92 

0.50  3240  1460  952  497  192  952  497  192  61.9  670  304  101  30.5 

0.55  3620  2010  1550  1070  629  1550  1070  629  327  1270  823  434  215 

0.60  3950  2540  2170  1800  1380  2170  1800  1380  997  1950  1590  1150  810 

0.65  4240  3030  2770  2560  2320  2770  2560  2320  2070  2640  2460  2180  1930 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  1.26  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  15.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  69.3  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  453  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  1050  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1680  0.98  0.04  0.01  0.01  0.35  0.01  0.01  0.01  0.15  0.01  0.01  0.01 

0.40  2270  21.9  2.08  0.18  0.02  10.9 0.95  0.08  0.01  5.94  0.50  0.04  0.01 

0.45  2790  150  31.6  5.50  0.94  96.7  18.3  3.05  0.57  65.1  11.5  1.92  0.38 

0.50  3240  497  192  61.9  18.7  384  136  41.8  13.2  304  101  30.5  9.92 

0.55  3620  1070  629  327  160  936  515  259  129  823  434  215  108 

0.60  3950  1800  1380  997  699  1690  1250  889  628  1590  1150  810  575 

0.65  4240  2560  2320  2070  1840  2510  2240  1990  1770  2460  2180  1930  1720 

Page 36: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-37

Table 2.E.28 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.25

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  36.8  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  343  0.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  889  8.20  0.09  0.01  0.01  0.09  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1500  90.2  6.84  0.16  0.01  6.84  0.16  0.01  0.01  0.81  0.02  0.01  0.01 

0.40  2080  332  76.2  7.06  0.37  76.2  7.06  0.37  0.02  20.8  1.37  0.06  0.01 

0.45  2600  729  307  73.0  9.96  307  73.0  9.96  1.05  142  24.9  2.73  0.26 

0.50  3060  1220  720  308  87.9  720  308  87.9  19.3  457  160  37.2  7.33 

0.55  3450  1750  1260  771  367  1260  771  367  145  966  530  218  79.0 

0.60  3800  2280  1860  1410  947  1860  1410  947  572  1600  1170  713  409 

0.65  4090  2770  2450  2140  1780  2450  2140  1780  1420  2270  1970  1570  1230 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.25  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  5.54  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  36.8  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  343  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  889  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1500  0.16  0.01  0.01  0.01  0.05  0.01  0.01  0.01  0.02  0.01  0.01  0.01 

0.40  2080  7.06  0.37  0.02  0.01  2.91  0.14  0.01  0.01  1.37  0.06  0.01  0.01 

0.45  2600  73.0  9.96  1.05  0.10  41.4  4.93  0.48  0.05  24.9  2.73  0.26  0.03 

0.50  3060  308  87.9  19.3  3.71  219  55.3  11.3  2.27  160  37.2  7.33  1.52 

0.55  3450  771  367  145  51.1  636  278  104  37.1  530  218  79.0  28.5 

0.60  3800  1410  947  572  320  1280  814  475  268  1170  713  409  231 

0.65  4090  2140  1780  1420  1100  2060  1670  1310  1020  1970  1570  1230  951 

Page 37: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-38

Table 2.E.29 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.375

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  20.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  267  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  769  3.43  0.02  0.01  0.01  0.02  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1360  56.1  2.48  0.03  0.01  2.48  0.03  0.01  0.01  0.19  0.01  0.01  0.01 

0.40  1930  246  42.6  2.37  0.07  42.6  2.37  0.07  0.01  8.77  0.33  0.01  0.01 

0.45  2450  594  212  37.0  3.32  212  37.0  3.32  0.22  83.1  9.99  0.70  0.04 

0.50  2920  1050  559  197  41.9  559  197  41.9  6.38  321  87.3  14.4  1.88 

0.55  3320  1560  1050  563  221  1050  563  221  66.9  755  351  113  30.1 

0.60  3670  2070  1620  1140  665  1620  1140  665  334  1330  873  453  209 

0.65  3970  2560  2200  1820  1390  2200  1820  1390  983  1980  1610  1150  778 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.05  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  2.07  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  20.0  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  267  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  769  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1360  0.03  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.40  1930  2.37  0.07  0.01  0.01  0.82  0.02  0.01  0.01  0.33  0.01  0.01  0.01 

0.45  2450  37.0  3.32  0.22  0.01  18.5  1.42  0.08  0.01  9.99  0.70  0.04  0.01 

0.50  2920  197  41.9  6.38  0.79  129  23.6  3.25  0.42  87.3  14.4  1.88  0.25 

0.55  3320  563  221  66.9  16.9  443  155  43.2  11.0  351  113  30.1  7.69 

0.60  3670  1140  665  334  148  993  542  258  115  873  453  209  92.5 

0.65  3970  1820  1390  983  655  1710  1250  865  575  1610  1150  778  516 

Page 38: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-39

Table 2.E.30 – Thinning Damage Factors

Corrosion Rate 0.508 mm/y (20 mpy), Excess Thickness Ratio minFCA t = 0.5

rtA Inspection Effectiveness

E 1 Inspection 2 Inspections 3 Inspections D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  11.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  213  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  677  1.50  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1240  36.2  0.94  0.01  0.01  0.94  0.01  0.01  0.01  0.05  0.01  0.01  0.01 

0.40  1810  189  24.6  0.84  0.02  24.6  0.84  0.02  0.01  3.85  0.09  0.01  0.01 

0.45  2330  494  151  19.4  1.18  151  19.4  1.18  0.05  50.4  4.21  0.19  0.01 

0.50  2800  918  444  130  20.9  444  130  20.9  2.26  232  49.6  5.96  0.52 

0.55  3210  1400  889  428  138  889  428  138  32.3  602  239  61.3  12.1 

0.60  3560  1910  1430  929  474  1430  929  474  200  1130  668  295  110 

0.65  3870  2400  1990  1570  1100  1990  1570  1100  690  1750  1330  849  500 

rtA Inspection Effectiveness

E 4 Inspections 5 Inspections 6 Inspections

D C B A D C B A D C B A

0.02  0.01  0.01  0.01  0.01  0.01 0.01 0.01 0.01 0.01 0.01 0.01  0.01  0.010.04  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.06  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.08  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.10  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.12  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.14  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.16  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.18  0.79  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.20  11.1  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.25  213  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.30  677  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.35  1240  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01  0.01 

0.40  1810  0.84  0.02  0.01  0.01  0.25  0.01  0.01  0.01  0.09  0.01  0.01  0.01 

0.45  2330  19.4  1.18  0.05  0.01  8.62  0.44  0.02  0.01  4.21  0.19  0.01  0.01 

0.50  2800  130  20.9  2.26  0.18  78.7  10.7  1.01  0.08  49.6  5.96  0.52  0.04 

0.55  3210  428  138  32.3  5.89  317  89.4  18.9  3.45  239  61.3  12.1  2.20 

0.60  3560  929  474  200  70.6  784  370  145  50.5  668  295  110  38.0 

0.65  3870  1570  1100  690  393  1440  958  579  328  1330  849  500  281 

Page 39: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-40

2.E.7 FIGURES

STEP 1: determine the following from Part 2, Section 5.0:

the number and the corresponding inspection effectiveness category used for all past inspections,the in-service age for corrosion, age, the starting thickness, trd, which is either last measured thickness or the furnished thickness,the corrosion rate for the base metal, Cr,bm, the corrosion rate for the cladding, if applicable, Cr,cm,the minimum required wall thickness, tmin,

and the remaining age of the cladding, agerc, if applicable.

STEP 4: Determine base damage factor, using the appropriate Table

2.E.1 through Table 2.E.30.

STEP 3: Determine Art

using Equation 2.E.2 or 2.E.3.

STEP 2: Determine the excess thickness ratio in the base metal,

xsr, using Equation 2.E.1

Figure 2.E.1 –Determination of the Base Damage Factor for Thinning

Page 40: api 581

API RP 581 RISK-BASED INSPECTION TECHNOLOGY

2.E-41

STEP 1: determine the following from Part 2, Section 16.0 or 17.0, as applicable:

the number and the corresponding inspection effectiveness category used for all past inspections,the in-service age for external corrosion, age, the starting thickness, trd, which is either last measured thickness or the furnished thickness,the corrosion rate for external damage, Cr,

and the minimum required wall thickness, tmin,

STEP 4: Determine damage factor, using the appropriate Table 2.E.1

through Table 2.E.30.

STEP 3: Determine Art

using Equation 2.E.5.

STEP 2: Determine the excess thickness ratio in the base metal,

xsr, using Equation 2.E.4

Figure 2.E.2 –Determination of the External Damage Factor