“mpp” air driven double diaphragm pumps1 mpp double diaphragm pumps simple operation double...
TRANSCRIPT
1 MPP
DOUBLE DIAPHRAGM PUMPS
SIMPLE OPERATIONDouble diaphragm pumps are operated by compressed air orany non-flammable compressed gas. The pumping strokebegins as air is delivered by the air distribution system, puttingpressure on one diaphragm and then the opposite diaphragm.The two diaphragms are linked together by a common rod.The pumping stroke on one side is simultaneously the suctionstroke on the opposing diaphragm alternately drawing fluid inone side while discharging fluid from the other side.
MAIN CHARACTERISTICSSelf-priming.Non-electrical.Runs dry without damage.Variable flow rate.Pumping fluids which contain particles.Reduced solvent flash-off.Adequate to pump high viscosity liquids.
TYPICAL APPLICATIONTransfer and recirculation of acid, alkali, ink, solvent, paint,enamel, resin, glue liquids, slurry, used in such industries as:chemical, pharmaceutical, ceramic, lather tanning, textile,metallurgical, paper, civil construction, alimentary.
ARGAL PUMPS ADVANTAGES
Quality built lube free, air operated diaphragm pumps.Wide range of pump types and sizes (1/4”÷3”).Standard NPT or BSP connections available on request.Will not stall at slow speeds.100% tested prior to shipment.Simple modular design.Dual manifold capability for 3/8"-1/2"-1" models.Parts interchangeable between models and sizes.Large solids handling through the Max-Pass valve system 3/8"-1/2"-1" pumps.
PERFORMANCE ENGINEERED
No stallouts:stallout due to freezing in the air system is virtually eliminateddue to the insulating quality of all plastic construction plus theability to slow air expansion and velocity without compromisingperformance. Stalling due to low speed is prevented by twopilot air ducts in the distributor which supply a constant airpressure against the air valve spool throughout the dischargestroke preventing the spool/shuttle combination to stop in aneutral position (Fig. 1).
Lube Free Operationachieved by using dissimilar plastic materials within the airsystem, shuttle mechanism constructed of lubrication filledmaterials and surface finishes held to strict engineering tole-rances.
All plastic air systems:in both metallic and plastic pumps prevent destruction of airsystem components from corrosive atmospheres or diaphragmruptures. No brass or aluminium components are used withinthe air system.All air system are glass filled polypropylene
No vent holes:the are no vent hole in our air valve. Vent holes needed toprevent stalling in competitive pumps allow corrosive fumes toenter and destroy valuable components. Additionally, if adiaphragm ruptures, fluid leakage cannot be routed to a safecontained zone.
No air lost when fluid discharge line are closed:air system seals and prevents air consumption when pump isnot transferring fluid; low coefficient of friction between the airsystem component translates in reduced air consumption.
MPP 2
The Max-Pass valve is ideal for inks, paints, adhesives, slurriesand other specialized applications.
Larger inner volumes:than competitive models with comparable performances,means more capacity per stroke and less wear on movingparts.
High viscosity applications:up to 22000 centipoises on all pumps from 3/8” to 3”. Up to4000 centipoises on 1/4” models.
Patented valve system:Max Pass™, optional valve sy-stem tolerates large solids andallows installation of the pumpin any position.• Increases solids handling ca-pability by 300% and suction liftby 25%.• Abrasion resistant.• Available in Nitrile, EPDM,Viton®.
3 MPP
DIAPRAGAMS CONSTRUCTION MATERIALS
Thermoplastic diaphragms:offer superior chemical and abrasion resistance and increased life cycle.The wide range of applications that these materials can address also makeordering the correct pump much easier.
Diaphragm are executed in materials as various as Geolast®, Santoprene®,PTFE, Viton®.Geolast®, is a nitrile based thermoplastic elastomer used in place of nitrile(Buna-N) or neoprene and urethane for non aggressive water based applications.Santoprene® is an EPDM based thermoplastic elastomer and is resistant tomild acids.Geolast®, Santoprene® are registered trademarks of Advanced ElastomerSystem
Elastomeric diaphragms:Viton® is a fluorinated elastomer with a broad resistance to most aggressivechemicals.Viton® is a registered trademarks of DuPont Dow Elastomers
Fluorinated diaphragms:PTFE is a synthetic fluoropolymer resistant to all chemicals.Superior PTFE overlay design does not require reduced diaphragm rod stroke,which reduces pump capacity by 20% on competitive pumps.Back-up diaphragms for PTFE overlays are Santoprene® which offers achemically resistant as “second line of defence”.
Process control:Solenoid control and cycle counting optional for most pumps.
CE and ATEX compliance:CE safety of Machineries and Quality Control certification have been obtainedfor all models.Argal is an ISO 9001:2000 certified company.All models are adequate to operate in Atex areas classified as Cat 3, Zone 2The metal pumps model 1 1/2" & 2" metal may comply to Atex Cat 2, Zone1 on request.The pump of 1" and smaller size constructed in metal and conductive nyloncomply to Atex Cat 2, Zone 1.
As you can see from the diagram above, as viscosities increase, the capacityof the pump decreases.Do not exceed 22000 centapoise on all 3/8" up to 3" pumps. Do not exceed4000 centapoise on 1/4" model.
80%
80%
60%
40%
20%
0
CENTAPOISE
CA
PA
CIT
Y
0 2 4 6 8 10 12 14 16 18 20 22
HIGH VISCOSITY APPLICATION
Valve spool
Pilot supplyair preventsstalling
Fig. 1
...our pumps do non require resetbuttons or magnets to insure.
121
184
162
41,5
AIR EXHAUST
60,5
4 x 9,5
Geolast®
Santoprene®
PTFEPTFEGeolast®
PTFEGeolast®
PTFESantoprene®
PTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFE
PolypropylenePolypropylenePolypropyleneNylonNylonNylonNylonPVDFPVDF
TTTTTTTTT
WWWWWWNYNYNYNYFPFP
NitrileEPDMPTFEPTFENitrilePTFEGeolast®
PTFEEPDM
NETTNTGTE
PolypropylenePolypropylenePolypropyleneNylonNylonConductive NylonConductive NylonPVDFPVDF
WWWWWWNYNYCYCYFPFP
MPP 025 WW G T WW NMPP 025 WW S T WW EMPP 025 WW T T WW TMPP 025 NY T T NY TMPP 025 NY G T NY NMPP 025 CY T T NY TMPP 025 CY G T NY GMPP 025 FP T T FP TMPP 025 FP S T FP E
GSTTGTGTS
2,52,52,52,52,53,53,53,53,5
656565656565659090
MPP - 025 (1/4”) 4
194
135,5
AIR INLET
73
117
140
29
DISCHARGE
SUCTION
EXECUTIONS
PLASTIC
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C
DIMENSIONS
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
6,8
5,4
4,1
2,7
1,3
0
1,7 3,4
5
6,5
AIR CONSUMPTION - Nm3/h
PERFORMANCE CURVES
0 4 8 12 16 18
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry liftMaximun solidsInlet air supplyOutlet air supplyFluid Inlet/DischargeNote: Dual manifold inlet/outlet is an option.
l/minmlbarbarmmmBSP/NPT FBSP/NPT FBSP/NPT F
16,3236,81,351,61/4"1/4"1/4"
NY
WW
FP
CY
5 038 (3/8”) - MPP
217
DISCHARGE
122,5
182,5
98
27
61
SUCTION
EXHAUST
AIRINLET
168,5
103
107 3,8 x 2
Geolast®
Santoprene®
PTFEPTFESantoprene®®PTFEPTFEPTFEGeolast®
PTFE
PolypropylenePolypropylenePolypropylenePolypropylenePVDFPVDFPVDFConductive NylonConductive NylonConductive Nylon
Nitrile Max-Pass™EPDM Max-Pass™PTFEViton Max-Pass™EPDM Max-Pass™PTFEViton Max-Pass™PTFENitrile Max-Pass™Viton Max-Pass™
N/AN/APolypropyleneN/AN/APVDFN/AStainless SteelN/AN/A
MPP 038 WW G N 00 NMPP 038 WW S E 00 EMPP 038 WW T T WW TMPP 038 WW T V 00 VMPP 038 FP G E 00 EMPP 038 FP T T FP TMPP 038 FP T V 00 VMPP 038 CY T T SS TMPP 038 CY G N 00 NMPP 038 CY T V 00 V
WWWWWWWWFPFPFPCYCYCY
NETVETVTNV
0000
WW0000FP00SS0000
NitrileEPDMPTFEViton®
EPDMPTFEViton®
PTFENitrileViton®
GSTTGTTTGT
NETVETVTNV
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C22222,52,52,52,52,52,5
65656565909090656565
EXECUTIONS
DIMENSIONS5
8,2
6,8
5,4
4,1
2,7
1,3
0 4 8 12 16 20 24 28 32 36
AIR CONSUMPTION - Nm3/h10 17
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
PERFORMANCE CURVES
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - with Max-Pass™ valvesMaximun solidsMax solids - with Max-Pass™ valvesInlet air supplyOutlet air supplyFluid Inlet/DischargeNote: Dual manifold split/delivery is an option.
l/minmlbarbarmmmmmmBSP/NPT FBSP/NPT FBSP/NPT F
34458,21,335,21,66,41/4"3/8"3/8"
CY
WW
FP
MPP - 050 (1/2”) 6
AIREXHAUST
187
288,5
161,5
51
123,5
DISCHARGE
SUCTION
306
156
173
257
AIRINLET
276
138
212
198,5
DISCHARGE
INLET28,5
138
ø 7 x 4112
5682
AIREXHAUST
132
105
187
102
82
96,5
PLASTIC
METALLIC
Geolast®
Santoprene®
PTFEViton®
Geolast®
PTFEViton®
PTFEGeolast®
Viton®
PTFESantoprene®
Viton®
Geolast®
Santoprene®
PTFEViton®
Geolast®
Santoprene®
PTFEViton®
PolypropylenePolypropylenePolypropylenePolypropyleneNylonNylonNylonConductive NylonConductive NylonConductive NylonPVDFPVDFPVDFAluminumAluminumAluminumAluminum316 Stainless Steel316 Stainless Steel316 Stainless Steel316 Stainless Steel
Geolast®
Santoprene®
PTFEViton®
Geolast®
PTFEViton®
PTFEGeolast®
Viton®
PTFESantoprene®
Viton®
Geolast®
Santoprene®
PTFEViton®
Geolast®
Santoprene®
PTFEViton®
PolypropylenePolypropylenePolypropylenePolypropylenePVDFPVDFPVDFStainless SteelStainless SteelStainless SteelPVDFPVDFPVDFPolypropylenePolypropyleneNylonNylonStainless SteelStainless SteelStainless SteelStainless Steel
MPP 050 WW G G WW NMPP 050 WW S S WW EMPP 050 WW T T WW TMPP 050 WW V V WW VMPP 050 NY G G FC NMPP 050 NY T T FP TMPP 050 NY V V FP VMPP 050 CY T T SS TMPP 050 CY G G SS NMPP 050 CY V V SS VMPP 050 FP T T FP TMPP 050 FP S S FP EMPP 050 FP V V FP VMPP 050 AL G G WW NMPP 050 AL S S WW EMPP 050 AL T T NY TMPP 050 AL V V NY VMPP 050 SS G G SS NMPP 050 SS S S SS EMPP 050 SS T T SS TMPP 050 SS V V SS V
WWWWWWWWNYNYNYCYCYCYFPFPFPALALALALSSSSSSSS
GSTVGTVTGVTSVGSTVGSTV
WWWWWWWWFPFPFPSSSSSSFPFPFP
WWWWNYNYSSSSSSSS
NitrileEPDMPTFEViton®
NitrilePTFEViton®
PTFENitrileViton®
PTFEEPDMViton®
NitrileEPDMPTFEViton®
NitrileEPDMPTFEViton®
GSTVGTVTGVTSVGSTVGSTV
NETVNTVTNVTEVNETVNETV
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C4,54,54,54,54,54,54,55,55,55,55,55,55,555559999
656565659090906565659090909090909090909090
EXECUTIONS
DIMENSIONS
8,2
6,8
5,4
4,1
2,7
1,3
0 8 16 24 32 40 48 56 64
AIR CONSUMPTION - Nm3/h3,5 1017 25
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
PERFORMANCE CURVES
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - other balls checkDry lift - with Max-Pass™ valvesMaximun solidsMax solids - with Max-Pass™ valves(optional)Inlet air supplyOutlet air supplyFluid Inlet/DischargeNote: Dual manifold split/delivery is an option.
l/minmlbarbarmmmmmmm
BSP/NPT FBSP/NPT FBSP/NPT F
64,5958,21,334,563,29,5
1/4"3/8"1/2"
NY WW
CYFP
SSAL
DISCH.321,5
301,5
8,586
171,5
198
36,5
AIREXHAUST
438,5
217
303,5
240,5
AIRINLET
358
173
DISCHARGE
SUCTION
225,5
414,5
66
159
SUCTION
225,5120,5
33,5
120,5120,5
104,5
127
53
7 100 (1”) - MPP
Geolast®
Santoprene®
PTFEViton®
PTFESantoprene®
Viton®
Geolast®
Santoprene®
PTFEViton®
Geolast®
Santoprene®
PTFEViton®
PolypropylenePolypropylenePolypropylenePolypropylenePVDFPVDFPVDFAluminumAluminumAluminumAluminum316 Stainless Steel316 Stainless Steel316 Stainless Steel316 Stainless Steel
Geolast®
Santoprene®
PTFEViton®
PTFESantoprene®
Viton®
Geolast®
Santoprene®
PTFEViton®
Geolast®
Santoprene®
PTFEViton®
PolypropylenePolypropylenePolypropylenePolypropylenePVDFPVDFPVDFPolypropylenePolypropyleneNylonNylonStainless SteelStainless SteelStainless SteelStainless Steel
MPP 100 WW G G WW NMPP 100 WW S S WW EMPP 100 WW T T WW TMPP 100 WW V V WW VMPP 100 FP T T FP TMPP 100 FP S S FP EMPP 100 FP V V FP VMPP 100 AL G G WW NMPP 100 AL S S WW EMPP 100 AL T T NY TMPP 100 AL V V NY VMPP 100 SS G G SS NMPP 100 SS S S SS EMPP 100 SS T T SS TMPP 100 SS V V SS V
WWWWWWWWFPFPFPALALALALSSSSSSSS
GSTVTSVGSTVGSTV
WWWWWWWWFPFPFP
WWWWNYNYSSSSSSSS
NitrileEPDMPTFEViton®
PTFEEPDMViton®
NitrileEPDMPTFEViton®
NitrileEPDMPTFEViton®
GSTVTSVGSTVGSTV
NETVTEVNETVNETV
PLASTIC
METALLIC
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C9,59,59,59,514141410,510,510,510,520,520,520,520,5
6565656590909,59,59,59,514141410,510,5
EXECUTIONS
DIMENSIONS
8,2
6,8
5,4
4,1
2,7
1,3
0 25 50 75 100 125 150 175
70
17
50
35 AIR CONSUMPTION - Nm3/h
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
PERFORMANCE CURVES
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - other balls checkDry lift - with Max-Pass™ valvesMaximun solidsMax solids - with Max-Pass™ valvesoptional for plastic pumpsMax solids - with Max-Pass™ valvesoptional for metal pumpsInlet air supplyOutlet air supplyFluid Inlet/Discharge plastic pumpsFluid Inlet/Discharge metal pumpsNote for plastic pumps:BSP 1" threaded connections are availableOptional threaded center ports must be specified
l/minmlbarbarmmmmmmm
mm
BSP/NPT FBSP/NPT FFlanged NDBSP/NPT F
1553158,21,334,55,56,519
12,7
1/4"3/8"251"
SS
WWFP
AL
MPP - 150 (1 1/2”) 8
Geolast®
PTFESantoprene®
PTFESantoprene®
Geolast®
Santoprene®
PTFEGeolast®
Santoprene®
PTFE
PolypropylenePolypropylenePolypropylenePVDFPVDFAluminumAluminumAluminum316 Stainless Steel316 Stainless Steel316 Stainless Steel
Geolast®
PTFESantoprene®
PTFESantoprene®
Geolast®
Santoprene®
PTFEGeolast®
Santoprene®
PTFE
PolypropylenePolypropylenePolypropylenePVDFPVDFPolypropylenePolypropyleneNylonStainless SteelStainless SteelStainless Steel
MPP 150 WW G G WW NMPP 150 WW T T WW TMPP 150 WW S S WW EMPP 150 FP T T FP TMPP 150 FP S S FP EMPP 150 AL G G WW NMPP 150 AL S S WW EMPP 150 AL T T NY TMPP 150 SS G G SS NMPP 150 SS S S SS EMPP 150 SS T T SS T
WWWWWWFPFPALALALSSSSSS
GTSTSGSTGST
WWWWWWFPFP
WWWWNYSSSSSS
NitrilePTFEEPDMPTFEEPDMNitrileEPDMPTFENitrileEPDMPTFE
GTSTSGSTGST
NTETENETNET
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C6565659090909090909090
212121303027,527,527,5606060
EXECUTIONS
DISCHARGE
522,5
480
553
312,5
79
ø 14 x 4237
284
SUCTION
AIRINLET
310
289
178
203
AIREXHAUST
AIRINLET
DISCHARGE
AIREXHAUST
SUCTION
495 302
324
127
152,5
527
590,5
316,5
81
ø 14 x 4236,5
283
PLASTIC
METALLIC
DIMENSIONS
8,2
6,8
5,4
4,1
2,7
1,3
0 70 140 210 280 350 420 490
AIR CONSUMPTION - Nm3/h6085 120
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
PERFORMANCE CURVES
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - other balls checkMaximun solidsInlet air supplyOutlet air supplyFluid Inlet/DischargeNote:Flanges are ISO and ANSI 1 1/2” compatible.
l/minlbarbarmmmmBSP/NPT FBSP/NPT FFlanged ND
4901,758,21,334,56,53/4"3/4"40
SS
WW
FP
AL
6565659090909090909090
22222231,531,5282828606060
9 200 (2”) - MPP
Geolast®
PTFESantoprene®
PTFESantoprene®
Geolast®
Santoprene®
PTFEGeolast®
Santoprene®
PTFE
PolypropylenePolypropylenePolypropylenePVDFPVDFAluminumAluminumAluminum316 Stainless Steel316 Stainless Steel316 Stainless Steel
Geolast®
PTFESantoprene®
PTFESantoprene®
Geolast®
Santoprene®
PTFEGeolast®
Santoprene®
PTFE
PolypropylenePolypropylenePolypropylenePVDFPVDFPolypropylenePolypropyleneNylonStainless SteelStainless SteelStainless Steel
MPP 200 WW G G WW NMPP 200 WW T T WW TMPP 200 WW S S WW EMPP 200 FP T T FP TMPP 200 FP S S FP EMPP 200 AL G G WW NMPP 200 AL S S WW EMPP 200 AL T T NY TMPP 200 SS G G SS NMPP 200 SS S S SS EMPP 200 SS T T SS T
WWWWWWFPFPALALALSSSSSS
GTSTSGSTGST
WWWWWWFPFP
WWWWNYSSSSSS
NitrilePTFEEPDMPTFEEPDMNitrileEPDMPTFENitrileEPDMPTFE
GTSTSGSTGST
NTETENETNET
DISCHARGE
522,5
600,5
677
357,5
89
ø 14 x 4305
355,5
SUCTION
AIRINLET
310
334
127
152,5
AIREXHAUST
AIRINLET
DISCHARGE
AIREXHAUST
SUCTION
A J
M
K
L
C
B
D
E
ø 14 x 4F
G
PLASTIC
METALLIC
DIMENSIONMODELSIZE (inlet/outlet) A B C D E F G J K L M2” Aluminium
NPT & BSP2” Stainless steel
NPT & BSPMetal optional flange
ND50 - 2” Flange
495
495
495
667
625,5
625,5
636
584
549
352
382,5
336,5
57
89
89
255,5
305
305
305
351,5
351,5
310
310
302
127
127
127
152,5
152,5
152,5
327,5
358
324
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C
EXECUTIONS
DIMENSIONS
8,2
6,8
5,4
4,1
2,7
1,3
AIR CONSUMPTION - Nm3/h50
85
0 70 140 210 280 350 420 490 560 630 685
120
DISCHARGE FLOW l/min.
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
PERFORMANCE CURVES
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - other balls checkMaximun solidsInlet air supplyOutlet air supplyFluid Inlet/Discharge plastic pumpsFluid Inlet/Discharge metal pumpsNote for plastic pumps:Flanges are ISO and ANSI 2” compatible.Note for stainless steel pumps: Optional tri-clamp fittings
l/minlbarbarmmmmBSP/NPT FBSP/NPT FFlanged NDBSP/NPT F
6801,828,21,334,56,53/4"3/4"502"
SS
WW FP
AL
MPP - 300 (3”) 10
90909090
59595959
UrethaneSantoprene®
PTFEViton®
AluminumAluminumAluminumAluminum
Geolast®
Santoprene®
PTFEViton®
NitrileEPDMNylonViton®
MPP 300 AL U G N0 0MPP 300 AL S S E0 0MPP 300 AL T T NY TMPP 300 AL V V V0 0
ALALALAL
GSTV
N0E0NYV0
N/AN/APTFEN/A
USTV
00T0
DISCHARGE
819
SUCTION
622
761
AIRSUPPLY
408
61
ø 15,5 x 4258129
426
258
284
CHAMBERS DIAPHRAGMS VALVE/BALL VALVE SEATS O-Rings ARGAL CODE WEIGHTMAX T.°C
EXECUTIONS
DIMENSIONS
8,2
6,8
5,4
4,1
2,7
1,3
PR
ES
SU
RE
INLE
T/O
UT
LET
(bar
)
40
85
130 170215
255
AIR CONSUMPTION - Nm3/h
DISCHARGE FLOW l/min.
PERFORMANCE CURVES
0 100 200 300 400 500 600 700 800 900 1000
MAIN CHARACTERISTICSMax CapacityVolume per strokeMax Air PressureMinimum Air PressureDry lift - with PTFE ballsDry lift - other balls checkMaximun solidsInlet air supplyOutlet air supplyFluid Inlet/DischargeAccessories: Carry handles and strainer base
l/minlbarbarmmmmBSP/NPT FBSP/NPT FBSP/NPT F
9604,678,21,334,5113/4"3/4"3”
Cycle CountingThe cycle count valve is integral to the air valve. The sensorat the bottom of the air valve is provided (the configurationfor data acquisition and control is not provided).Every time a cycle is completed, an impulse is sent from thecycle count valve to a data acquisition center for automatedinput to a PC, PLC, relay or switch. The cycle count can beused on pumps 3/8" and larger.
Solenoid ControlThe solenoid control valve is used for remote, electricalcontrol of a pump through a PC, PLC, relay or switch.The solenoid control valve replaces the air valve as-sembly. The control signal is a solution to "on demand"fluid transfer requirements. Supply voltage: 220VAC/50Hz, 120V AC/60Hz, 24V DC. The solenoidcontrol can be used on pumps 3/8" and larger.
Drum KitsThe many advantages of diaphragmpumps make them ideal for drumevacuation.Drum mounting kits are available forpumps up to 1" in size.
ACCESSORIES
AL
0708
Member of AIBassociazioneindustrialebresciana
IT - 25125 BRESCIA - Via Labirinto, 159Tel. +39 030 3507011 - Fax +39 030 3507077
Export dpt. Tel. +39 030 3507033Web: www.argal.it - E-mail: [email protected]
It is the policy of ARGAL to always improve its products and the right is reserved to alter specifications at any time without prior notice.No part of this publication may be reproduced in any form or any means.
Production Program
ZGE range (ISO 2858)
Installed powers: kW 0,55÷300Bodies materials: PP - PVDF - PVC - PE HMW
• Sealed
ROUTE range
Installed powers: kW 0,55÷7,5Bodies materials: GFR/PP - CFF/E-CTFE
• Magnetic drive• Sealed
ZME range
Installed powers: kW 5,5÷15Bodies materials: PP - E-CTFE
• Sealed
FRONTIERA range
Installed powers: kW 0,55÷15Bodies materials: PP - E-CTFE
• Magnetic drive• Sealed
KGK range
Installed powers: kW 0,25÷15Bodies materials: GFR/PP - PVDF - PVC
Lenghts 250÷4000 mm
K range (KG and KM)
Installed powers: kW 0,75÷37Bodies materials: GFR/PP - PVDF - PVCLenghts 400÷3000 mm
ZMA and ZGA range
Installed powers: kW 0,75÷11Bodies materials: PP - PVDF - PVC
• Self priming• Sealed
AM range
Installed powers: kW 0,18÷0,55Bodies materials: GFR/PP - E-CTFE
• Magnetic drive
TMB range
Installed powers: W 15÷100Bodies materials: GFR/PP
• Magnetic drive
ZM range
Installed powers: kW 0,75÷11Bodies materials: GFR/PP - CFF/PVDF
• Sealed
LAGUNA range
Range: from 500 to 40.000 l/hFilter materials: PP - PVDFPump materials: GFR/PP - CFF/E-CTFE
EQUIPRO range
Available motor power: 0,25÷4 kWMaterial versions: GFR/PP – PVDF
Lenghts 275 - 450 mm