ansi b36.19: welded and seamless wrought steel pipe
TRANSCRIPT
By Authority OfTHE UNITED STATES OF AMERICA
Legally Binding Document
By the Authority Vested By Part 5 of the United States Code § 552(a) and Part 1 of the Code of Regulations § 51 the attached document has been duly INCORPORATED BY REFERENCE and shall be considered legally binding upon all citizens and residents of the United States of America. HEED THIS NOTICE: Criminal penalties may apply for noncompliance.
Official Incorporator:THE EXECUTIVE DIRECTOROFFICE OF THE FEDERAL REGISTERWASHINGTON, D.C.
Document Name:
CFR Section(s):
Standards Body:
e
AMERICAN NATIONAL STANDARD FOR WELDED AND SEAMLESS WROUGHT STEEL PIPE (ANSI 836.10 .. 1979)1
FOREWORD
In March, 1927, the American Standards Association authorized the organization of a Sectional Commit· tee on Standardization of Dimensions aizd Material of Wrought Steel and Wrought Iron Pipe and Tubing, for the purpose of unifying the standards of these commodities in force in this country. The American Society for Testing and Materials and The American Society of Mechanical Engineers were designated as sponsors and the first meeting of the sectional committee was held in Pittsburgh, Pa., on May 18,1928.
The dimensions of commercial pipe, in general use in the United States at the time, conformed rather generally to, those recommended by the ASME Committee on Standard Pipe and Pipe Threads, published in 1886 (ASME Trans., vol. VIII, page 29). On these standards an enormous industry has been built and the satisfactory use of this product proves the soundness of the original design and specification.
Increa:singly severe service demands at the time of the committee's organization, had been met by using the nearest available pipe or tubing for heavier secfions, such as casing, mechanical tubing, etc., with result· ing uneconomical multiplicity of wall thicknesses.
Subsequently; the committee, with the cooperation of the industry, made a survey of existing practice as the logical statting point for the development of an American Standard.
From this survey, a Table was designed to provide a selection of wall thicknesses of pipe to cover the power piping requirements of industry where strength to resist internal pressure governs selection and was later expanded to include pipe diameters and thicknesses used in other industries.
The original intent of the Committe.e was to establish a system of Schedule Numbers for pipe size/wall combinations which would have an approximately uniform relationship equal to 1000 times the PIS expres· sion contained in the modified Barlow formula for pipe wall thickness as defined in the Appendix to this standard. The resulting Numbers departed so far from existing wall tllicknesses in common use that the original intent could not be accOlilplished. The Scheoule Numbers were th'E:n adopted strictly as a convenient designation system for use in ordering.
In all cases, the designer must base his selection on the rules and allowable stresses set by the code which goverIls his particular construction. The table is dimensionally complete for all sizes and wall thicknesses within its scope, but some of the larger, heavier wall sections are beyond the capability of seamless mill production and must be obtained from forged and bored billets or other sources.
The first issue, of this Standard was approved by letter ballot of the Sectional Committee in October 1934; by The American Society of Mechanic,al Engineers in November 1934, and by the AmericaIi Society for Testing and Materials in February 1935. Formal approval was given with the designation American Stan· dard' "tentative," by the American Standards Association, November 1935.
Subsequent slight revisions to Table 1 and the footl\otes of the dimensional tables were approved in order by the Sectional Committee, the Sponsors, and the Am~rican Standards Association, The latter changed the designation to American Standard; date of approval April 28, 1939.
Further revisions have been made by the Sectional Committee and approved by the Sponsors and the American Standards Association. The list of specifications in Table I has been revised where necessary and slight revisions in wall thicknesses of some of the large sizes of the heavy schedules have been made where PIS values were out of line.
It was the hope in 1939 that the designations of pipe used commercially by all industry as standard weight, extra strong, and double extra strong would gradually be replaced by Schedule Number designation. However, owing to customs of over fifty years' standing, demand and production of pipe to these traditional dimensions is undiminished. Consequently. in response to a demand from users, accepted practice for dimensions and weights of commercial wrougllt steel and welded wrought iron pipe, were added.
These changes in the Standard were approved by the Sectional Committee, the Sponsors, and the Amer· ican Standards Association, and it was designated an American Standard on February 23. 1950.
106.8
Subcommittee No.1 was reorganized in 1957 to revise and bring the Standard up to date. In addition to the necessary editorial.changes, a simplified format was selected for the tables of weights and dimensions so as to include and to identify the sizes and weights of API Standards 5L and 5 LX. The decimal wall thicknesses and plain end weights were established by a uniform procedure recognized by the tubular industry, and for some sizes the decimal wall thicknesses and plain end weights shown may vary slightly from those shown in the tables of previous issues of this Standard.
These changes were approved by the Sectional Committee, the Sponsors, and the American Standards Association, and it was designated an American Standard on December 21,1959.
This Standard was revised in 1969 to bring it up to date. A uniform method to calculate the plain end weight of steel pipe was included, and minor adjustments were made in the tabulated weights of steel pipe in Table 2 to conform to this new method. Additional sizes and thicknesses of steel pipe which have come into common use were also added to Table 2.
Inasmuch as API Standard 5L no longer included wrought iron pipe, reference to this API Standard was deleted from Table 3.
These changes in the Standard were approved by the Standards Committee, the Sponsors, and the American National Standards Institute, and it was designated an American National Standard on February 3, 1970.
Further revisions were made .(0 this Standard in 1975. Additional sizes and thickness of steel pipe which had been added to API Specifications were added to Table 2. Table 3, Dimensions and Weights of Welded Wrought Iron Pipe was deleted in its entirety, since wrought iron pipe is no longer produced.
These changes in the Standard were approved by the Standards Committee, the Secretariat, and the American National Standards Institute, and it was designated an American National Standard on June 5, 1975. . .
This Standard was revised in 1978 to include SI metric dimensions. The outside diameter and wall thicknesses were converted to mm by multiplying the inch dimensions by 25.4. Outside diameters larger than 16" were rounded to' the nearest mm, and outside diameter 16" and smaller were rounded to the nearest 0.1 mm. Wall thicknesses were rounded to the nearest 0.01 mm. These converted and rounded SI metric dimensions were adde.d to Table 2.' A formula to calculate the SI metric plain end mass', kg/m, using SI metric diameters and thicknesses was adde.d to SectionS. TheSI metric plain end mass was calculated for each size and thickness, and was added to Table 2.
These changes in the Standard were approved by the Standards Committee. the Secretariat, and the American National Standards Institute, and it was designed an American National Standard on July 18,1979
1 Reprinted by permission of the 'American Society of Mechanical Engineers, 345 East 47th St., New York, N.Y. 10017.
1069
ANSI 836.10-1979
AMERICAN NATIONAL STANDARD
WELDED AND SEAMLESS WROUGHT STEEL PIPE
1. SCOPE
This Standard covers the standardization of dimensions of welded and seamless wrought steel pipe, for high or low temperatures and pressures.
The word pipe is used as distinguished from tube to apply to tubular products of dimimsions commoil1y used for pipelin.e and piping systems. Pipe dimensions of sizes 12 inch and smaller have ou'tside diameters numerically larger than corresponding sizes. In contrast, the outside diameters of tubes are numerically
identical to the size number for all sizes.
:1. SIZE
The size of all pipe is iden tified by the nominal pipe size.
The manufacture of pipe in the nominal sizes of 1/8 inch to 12 inches inclusive is based on a standardized outside diameter (OD). This OD was originally selected so that pipe with a standard OD and having a wall thickness which was typical of the period would have an inside diameter (ID) approximately equal to the nominal size. Although there is no such relation between the existing standard thickness-OD and nominal size-these nominal sizes and standard ODs continue in use as "standard."
The manufacture of pipe in nominal sizes of 14 inch OD and larger. proceeds on the basis of an OD corresponding to the nominal size.
3. MATERIALS
The dimensional standards for pipe described here arc for products covered in the ASTM and API specifi· cations listed in Table 1.
4. WALL THICKNESS
The nominal wall thicknesses are given in Table 2. Table 2 also indicates wall thicknesses listed in API Standards 5L, 5LX and 5LS.
5. WEIGHTS
The nominal weights of steel pipe are calculated values and are tabulated in Table 2.
The nominal plain end weights, lbs./ft., are cal· culated using the following formula:
Wpe = 10.68 (D - t) t
where
Wpe = nominal plain end weight rounded to the nearest 0.01 lb./ft.
D = outside diameter to the nearest 0.001 in . . (The symbol D is to be used for 00 only in
h1athematical equations or fomulas.)
= specified wall thickness rounded to the nearesfD.OOl in:
The nominal plain _end mass, kg/m, is calculated using the following formula:
Wpe = 0.02466 (D - /) /
where
Wpe = nominal plain end mass rounded to the nearest 0.0 1 kg/m
D = outside diameter (0 the nearest 0.1 mm for outside diameters which are 16 in. and smaller and 1.0 mm for outside diameter larger than 16 in. (The symbol D is to be used for OD only in mathematical equations or formulas).
specified wall thickness rounded to the ncarest 0.0 I mm.
6. PERMISSIBLE VARIATIONS
Variations in dimensions differ depending upon the method of manufacture cmployed in maldng the pipe to the various specifications listed in Table 1. Permis' sible variations for dimensions are indicated in each
specification.
1070
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
7. PIPE THREADS
Unless otherwise specified, the threads of threaded pipe shall conform to ANSI B2.l Pipe Threads (Ex· cept Drysea/).
8. WALL THICKNESS DESIGNATIONS
The wall thickness designations "Standard", "Extra·Strong", and Double Extra·Strong" have been commercially used designations for many years. As ex· plained in the Foreword, the Schedule Numbers were subsequently added as a convenient designation for use in ordering pipe. Standard and Schedule 40 are iden· tical for nominal pipe sizes up to 10 inch inclusive. All larger sizes of Standard have 3/8 inch wall thickness. Extra·Strong and Schedule 80 are identical for nom· inal pipe sizes up to 8 inch inclusive. All larger sizes of Extra·Strong have 1/2 inch wall thickness.
/
1071
Pipe'of sizes and wall thickness other than those of Standard, Extra·Strong, Double Extra Strong, and Schedule Number were adopted from API Standards 5L, 5LX and 5LS. It was not considered practical to establish Schedule Numbers nor new designations for them.
9. WALL THICKNESS SELECTION
When the selection of wall thickness depends primarily upon capacity to resist internal pressure under given conditions, the designer shall compute the exact value of wall thickness suitable for conditions for which the pipe is required as prescribed in detail in the ASME Boiler and Pressure Vessel Code, ANSI B3l Code for Pressure Piping, or other similar codes, whichever governs the construction. A thickness shall be selected from Table 2 to suit the value computed to fulflll the conditions for which the pipe is desired.
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 1 Specifications for Pipe with ANSI Designations and Titles of Standard Specifications
ASTM or Ap·1 Designation
ASTM A53
ASTM A106
ASTM A120
ASTM A134
ASTM A135
ASTM A139
ASTM A155
ASTM A211
ASTM A312
ASTM A333
ASTM A335
ASTM A358
ASTM A369
ASTM A376
ASTM A381
ASTM A405
ASTM A523
ASTM A524
ASTM A530
API 5L
API5LX
API5LS
ANSI Designation
8125.1
8125.30
8125.2
8125.55
8125.3
8125.31
8125.4
8122.56
8125.16
8125.17
8125.24
8125.57
8125.27
8125.25
8125.35
8125.26
G62.5
8125.37
8125.20
Title
Welded and Seamless Steel Pipe
Seamless Carbon Steel Pipe for High-Temperature Service
81ack and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless Steel Pipe for Ordinary Uses
Electri~-Fusion (Arc)-Welded Steel Plate Pipe (Sizes 16 in. and Over)
Electric-Resistance-Welded Steel Pipe
Electric-Fusion (Arc)-Welded Steel Plate Pipe (Sizes 4 in. and Over)
Electric-Fusion-Welded Steel Pipe for High-Pressure Service
Spiral-Welded Steel or Iron Pipe
Seamless and Welded Austenitic Stainless Steel Pipe
Seamless and Welded Steel Pipe for Low·Temperature Service
Seamless Ferritic Alloy Steel Pipe for High-Temperature Service
Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe :or HighTemperature Service
Carbon and Ferritic Alloy Steel Forged and 80red Pipe for High-Temperature Service
Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service
Metal-Arc-Welded Steel Pipe for High-Pressure Transmission Systems
Seamless Ferritic Alloy Steel Pipe Specially Heat Treated for High·Temperature Service
Plain End Seamless and Electric-Resistance-Welded Steel P;pe for High Prec:;sure Pipe-Type Cable Circuits
Seamless Carbon Steel Pipe for Process Piping
General Requirements for Specialized Carbon and Alloy Steel Pipe
Line Pipe
High-Test Line Pipe
Spiral Weld Line Pipe
1072
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10·1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe
Inch Units
Plain Inch Outside Wall En,d
Nominal Diameter Thickness Weight Size in. in. Ib/ft
'/. '/.
Yo Yo
'/. %
y, y, y, y,
% % % %
1Y4 1% 1% 1%
1% 1% 1% 1%
2 2
2 2
2 2 2 2 2 2
0.405 0.405
0.540 0.540
0.675 0.675
0.840 0.840 0.840 0.840
1.050 1.050 1.050 1,050
1.315 1.315 1.315 1.315
1.660 1.660 1.660 1.660
1.900 1.900 1.900 1.900
2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375
0.068 0.095
0.088 0.119
0.091 0.126
0.109 0.147 0.188 0.294
0.113 0.154 0.219 0.308
0.133 0.179 0.250 0.358
0.140 0.191 0.250 0.382
0.145 0.200 0.281 0.400
0.083 0.109 0.125 0.141 0.154 0.172 0.188 0.218 0.250 0.281 0.344 0.436
0.24 0.31
0.42 0.54
0.57 0.74
0.85 1.09 1.31 1.71
1.13 1.47 1.94 2.44
1.68 2.17 2.84 3.66
2.27 3.00 3.76 5.21
2.72 3.63 4.86 6.41
2.03 2.64 3.00 3.36 3.65 4.05 4.39 5.02 5.67 6.28 7.46 9.03
5L 5L
5L 5L
5L 5L
5L 5L
5L
API Specs
5L 5L,
5L
5L 5L
5L
5L 5L
5L
5L 5L
5L
5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX
5L5LX
51 Units Identification
Standard (STD) Outside Wall X·strong (X) 'Schedule Diameter Thickness
XX·strong (XXS) No. mm mm
STD XS
STD
XS
STD XS
STD XS
XXS
STD XS
XXS
STD XS
XXS
STD XS
XXS
STD XS
XXS
STD
XS
XXS
40 80
40 80
40 80
40 80
160
40 80
160
40 80
160
40 80
160
40 80
160
, . 40
80
10.3 10.3
13.7 13.7
17.1 17.1
21.3 21.3 21.3 21.3
26.7 26.7 26.7 26.7
33.4 33.4 33.4 33.4
42.2 42.2 42.2 42.2
48.3 48.3 48.3 48.3
60.3 . 60.3
60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3
1.73 2.41
2.24 3.02
2.31 3.20
2.77 3.73 4.78 7.47
2.87 3.91 5.56 7.82
3.38 4.55 6.35 9.09
3.56 4.85 6.35 9.70
3.68 5.08 7.14
10.15
2.11 2.77 3.18 3.58 '3.91 4.37 4.78 5.54 6.35 7.14 8.74
11.07
·N-Item not shown in ANSI 836.10-1975 which has been added to API Specifications. C-Corrected listing for an item that 'was incorrectly listed in ANSI 836.10-1975. No Code Letter-Item correctly listed in ANSI 836.10-1975.
1073
Plain End Previous Mass Statu5 kg/m
0.37 0.47
0.63 0.80
0.84 1.10
1.27 1.62 1.95 2.55
1.69 2.20 2.90 3.64
2.50 3.24 4.24 5.45
3.39 4.47 5.61 7.77
4.05 5.41 7.25 9.56
3.03 3.93 4.48 5.01 5.44 6.03 6.54 7.48 8.45 9.36
11.11 13.44
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE . . ANSI 836:10-1979
Table,2 Dimensions arid Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch UnitS 81 Units
Plain Identification
Plain Incn Outside Wall End Standard (STDJ Outside Wall End Previous
Nominal Diameter Thickness Weight API Specs
X-strong (X) Schedule Diameter Thickness Mass Status Size in. in. Ib/ft XX'strong (XXSJ No. mm mm kg/m
2% 2% 2% 2% 2% 2~
2Ya 2% 2% 2% 2% 2% 2%
2.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875
.. 2.875 2.875 ·2.875 2.875
0.083 0.109 0.125 0.141 0.156 0.172 0.188 0.203 0.216
2.47 3.22 3.67 4.12 4.53 4.97 5,40 5.79 6.13
5L5LX 5L5LX 5L5LX 5L 5LX 5L5LX 5L5LX 5L5LX 5L 5LX 5L 5LX
0.250 7eOl 5L 5LX 0.276 7.66 5L 5LX 0.375 . 10.01 0.552 13.69 5L 5LX
3 3.500 0.083 3.03 5L 5LX 3 3.500 0.109 3.95 5L 5LX 3 3.500 0.125 4.51 5L 5LX 3 3.500 0.141 5.06 5L 5LX 3 3.500 0.156 5.57 5L 5LX
STD
XS
XXS
40
80 160
--:;3 ___ -:3,:.;.5;.:0"'0 __ .,,0'-:.1"'72, 6.11 5L 5~L",X _________ _ 3 3.500 0.188 6.65 5L 5 LX 3 3.500 0.216 7.58 5L5LX 3 3.500 0.250 8.68 5L 5LX
3 3 3
3.500 0.281 9.66 5L 5LX 3.500 0.300 10.25 S L 5 LX 3.500 0,438 14.32 3.S00 0.600 18.58 5L 5LX
STD
XS
XXS
40
80 160
73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0 nO 73.0 73.0
88.9 88.9 88.9 88.9 88.9 88.9 -88.9 88.9 88.9 88.9 88.9 88.9 88.9
3~ 4.000 0.083 3,47 5L 5LX 101.6 3~ 4.000 0.109 4.53 SL5LX 101.6
~3Y.~' ____ ~4~.0~0~0~ __ ~0~'iI2~5~ __ ~5~.~'7~~5~L~5~L~X~ _________________________ ':0'.6 3~ 4.000 0.141 5.81 5L·SLX 101.6 3~ 4.000 0.156 6,40 5L 5LX 101.6 3~ 4.000 0.172 7.03 5L 5LX 101.6 3~ 4.000 0.188 7.65 5L 5LX 101.6 3~ 4.000 0.226 9.11 5L5LX STD 40 101.6 3~ 4.000 0.250 10.01 5L 5LX 101.6 3~ 4.000 0.281 11.16 5L5LX 101.6 3~ 4.000 0.318 12.50 5L 6LX XS 80 101.6
4 4.500 0.083 3.92 5L 5LX 5LS 114.3 4 4.500 0.109 5.11 5L 5LS 114.3
~:-------=:;:':~"'~S~~--~~;;::.;.~ ~T.~;----'~;;::~~:~---;~~~'-:~:';~"'~~~:=:~~~----------------------:.'-:'~ ~ H 4 4.500 0.156 7.24 5L 5LX 5LS 114.3 4 4.500 0.172 7.95 5L5LX5LS 114.3 4 4.500 0.188 8.66 5L5LX5LS 114.3 4 4.500 0.203 9.32 5L 5LX 5LS 114.3 4 4.500 0.219 10,01 5L 5LX 5LS 114.3 4 4.500 0.237 10.79 5L 5LX 5LS STD 40 114.3
1074
2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.16 5,49 6.35 7.01 9.53
14.02
3.69 4.80 5,48 6.13 6.74 7,40 8.04 8.63 9.14
10.44 11,41 14.92 20.39
2.11 4.52 2.77 5.88 3.18 6.72 3.58 7.53 3.96 8.29 4.37 9.11 4.78 9.92 5.49 11.29 6.3:,,5'--_712~.~~ ___ _ 7.14 14,40 7.62 15.27
11.13 21.35 15.24 27.68
2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.74 6.35 7.14 8.08
.2.11 2.77 3.18 3.58 3.96 4.37 4.78 5·16 5.56 6.Q2
5.18 6.75 7.72 8.65 9.53
10,48 11,41 13.57 14.92 16.63 18.63
5.84 7.62 8.71 9.77
10.78 11.85 12.91 13.89 14.91 16.07
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI B36.10·197~
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Waight Size in. in. Ib/ft
4
4 4 4 4 4
5 5 5 5 5 5 5 5 5
6 6
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
4.500 4.500 4.500 4.500 4.500 4.500 4.500
"5.563. 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563
6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625
0.250 0.281 0.312 0.337 0.438 0.531 0.674
0.083 0.125 0.156 0.188 0.219 .0.258 0.281 0.312 0.344 0.375 0.500 0.625 0.750
0.083 ·0.109 0.125 0.141 0.156 0.172 0.188 0.203 0.219 0.250 0.280 0.312 0.344 0.375 0.432 0.500 0.562 0.625 0.719 0.864
11.35 12.66 13.96 14.98 19.00 22.51 27.54
4.86 7.26 9.01
10.79 12.50 14.62 15.85 17.50 19.17 20.78 27.04 32.96 38.55
5.80 7.59 8.68 9.76
10.78 11.85 12.92 13.92 14.98 17.02 18.97 21.04 23.08 25.03 28.57 32.71 36.39 40.05 45.35 53.16
8 8.625 0.125 11.35 8 8.625 0.156 14.11
~8~_-,-_8~.:!.62~5,-__ 0~'c'.1",88~_..!.-"16.94 8 8.625 0.203 18.26 8 8;625 0.219 19.66 8 8.625 0.250 22.36 8 8.625 0.277 24.70
API Specs
5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS
5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L
5LS 5LS 5LS 5LS 5LS 5LS 5LS 5LS 5LS
5LS 5LS
5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX tLS 5L 5LX 5LS 5L
5L5LX 5LS 5L5LX 5LS 5L 5LX 5LS
5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS
81 Units Identification
Plain Standard (STOI Outside Wall End Previous
X-strong (X) Schedule Diameter Thicknt:ss Mass Status XX·strong (XXSI No. mm mm kg/m
XS
XXS
STO
XS
XXS
STO
XS
XXS
1075.
80 120 160
40
80 120 160
40
80
120
160
20 30
114.3 114.3 114.3 114.3 114.3 114.3 114.3
141.3 141.3 141.3 141.3 141.3
.141.3 141.3 141.3 141.3 141.3 141.3 141.3 141.3
168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3
6.35 7.14 7.92 8.56
11.13 13.49 17.12
2.11 3.18 3.96 4.78 5.56 6.55 7.14 7.92 8.74 9.53
12.70 15.88 19.05
,2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.16 5.56 6.35 7.11 7.92 8.74 9.53
10.97 12.70 14.27 15.88 18.26 21.95
16.90 18.87 20.78 22.32 28.32 33.54 41.03
7.24 10.83 13.41 16.09 18.61 21.77 23.62 26.05 28.57 30.97 40.28 49.11 57.43
8.65 11.31 12.95 14.54 16.05 17.67 19.27 20.76 22.31 25.36 28.26 31.32 34.39 37.31 42.56 48.73 54.20 59.69 67.56 79.22
219.1 3.18 16.93 219.1 3.96 21.01
c
_~~.1 __ ~4~."7,8~_-=2~5~.2~6 ___ __ 219.1 5.16 27.22 219.1 5.56 29.28 219.1 6.35 33.31 219.1 7.04 36.81
AMERICAN NATIONAL STANDARD WELDED·AND:SEAMLESS WROUGHT STEEL PIPE ANSIB36.1 ()';1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Out'side Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/ft
8 8 8 8 8 8 8 8 8 8 8 8 8 8
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625
'.8.625 8.625 8.625 8.625
10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10,750 10.750 10.750 10.750 10.750 10.750 10.750 10.750
12.750 12.750 12.750 12.750 12,750 12.750 12.7S0 12.7S0 12.7S0 12.750 12.750 12.750 12.7S0 12.7S0 12.750
0.312 0.322 0.344 0.375 0;406
.0.438 0.500 0.562 0.594 0.625 0.719
. 0.812 0.875 0.906
0.156 0.188 0.203 0.219 0.250 0.279 0.307 0.344 0.365 0.438
.27.70 5L 5LX 5LS 78.55 5L 5LX 5LS 3Q.42 5L 5LX 5LS 33.04 5L 5LX 5LS 35.64 38.30 5L 5LX 5LS 43.39 5L 5LX 5LS 48.40 5L 5LX 5LS 50.95 53.40 5L 5LX 5LS 60.71 5L 5LX 5LS 67.76 72.42 5L 74.69
1.7.65 5L 5LX 5LS 21..21 5L 5LX 5LS 22.87 5 LX 5 LS 24.1>3 5L 5LX SLS 28.04 SL SLX SLS 31.20 5L 5LXSLS 34.24 5L 5LX 5LS 38.23 5L 5LX 5LS 40.48 5L 5LX 5LS 48.24 5L 5LX 5LS
0.500 ", 54.74 5L 5LX 5LS 0.562 61.15 5L5LX5LS 0.594 0.625 0.719 0.812 0.844 1.000 1.125
0.172 0.188 0.203 0.219 0.250 0.281 0.312 0.330 0.344 0.375 0.406 0.438 0.600 0.562 0.625
64-.43 67.58 5L 5LX 5LS 77.03 5L SLX 5LS 86.18 5L 5LS 89.29
104.13 115.64
23.11 5L 5LX 5LS 25.22 5L 5LX 5LS 27.20 5LX 5LS 29.31 5L 5LX 5LS 33.38 5L 5LX 5LS 37.42 5L 5LX 5LS
_41.4S SL SLX 5LS 43.77 SL SLX SLS 45.58 SL SLX 5LS 49.S6 5L SLX 5LS 53.S2 5LX 5LS S7.59 5L SLX SLS 65.42 5L 5LX SLS 73.15 5L5LXSLS 80.93 5L SLX SLS
51 Units Identification
Standard (STD) Outside Wall X~strong (X) Schedule Diameter Thickness
XX·strong (XXS) No. mm mm
STD
XS
XXS
STD
XS
XXS
STD
XS
1076
40
60
80'
100
120 140
160
20
30
40
60
80
100
120 140 160
20
30
40
60
219.1 219.1 219.1 219.1 219.1 219.1 219 .. 1 219.1 219.1 219 .. 1 219.1 219.1 219.1 219.1
273.1 273.1 273.1 273.1 273,1 2}3.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1
323.9 3.23.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9
7,92 8.18 8;74 9.53
10.31 11.13
'·12.70 14.27 15.09 15.88 18.26 20.62 22.23 23.01
3.96 4.78 S.16 5.56 6.35 7.09 7.80 8.74 9.27
11.13 12.70 14.27 15.09 15.88 18.26 20.62 21.44 25.40 28.58
4.37 4.78 5.16 5.56 6.35 7.14 7.92 8.38 8.74 9.S3
10.31 11.13 12.70 14.27 lS.88
Plain End Previous
Mass ,Status kgim
41.24 42.55 45.34 49.25 53.08 57.08 64.64 72.08 75.92 79.58 90.44
100.92 107.92 111.27
26.28 31.63 34.09 36.68 41.77 46.51 51.03 56.98 60.31 71.90 81.55 91.08 96.01
100.73 114.75 128.38 133.06 155.15 .172.33
34.43 37.62 40.56 43.65 49.73 5S.77 61.71 65.20 67.93 73.88 79.73 85.84 97.46
108.96 120.62
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI B36.1 0-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/ft
12 12 12
12.750 12.750 12.750
0.G88 0.750 0.812
88.63 5L 5LX 5LS 96.12 5L 5LX·5LS
103.53 5L 5LX 5LS
SI Units (Identification
Standard (STDI Outside Wall X-strong (X) Schedule Diameter Thickness
XX·strong (XXSI No. mm mm
80 323.9 323.9 323.9
17,48 19.05 20.62
Plain End Previous Mass Status kg/m
132.08 143.21 154.21
12 12 12
12.750 12.750 12.750
0.844 0.875 1.000
107.32 100 323.9 323.9 323.9
21.44 22.23 25,40
159.91 165.37 186.97
12 12
12.750 12.750
1.125 1.312
14 14.000 0.188 14 14.000 0.203 14 14.000 0.210 14 14.000 0.219 14 14.000 0.250 14 14.000 0.281 14 14.000 0.312 14 14.000 0.344 14 14.000 0.375 14 14.000 0,406 14 14.000 0.438 14 14.000 0,469 14 14.000 0.500 14 14.000 0.562
--'1_'_4_~__'1_'_4:;:.0.:;0=_0 _-:;0.594 14 14.000 0.625 14 14.000 0.688 14 14.000 0.750 14 14.000 0.812 14 14.000 0.875 14 14.000 0.938 14 14.000 1.094 14 14.000 1.250 14 14.000 1.406 14 14.000 2.000 14 14.000 2.125 14 14.000 2.200 14 14.000 2.500
16 16 16 16 16 16 16 16 16 16 16 16
16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000
0.188 0.203 0.219 0.250 0.281 0.312 0.344 0.375 0,406 0.438 0.469 0.500
110.97 5L5LX5LS 125,49 139.67 160.27
27.73 5L5LX5LS 29.91 5L 5LS 30.93 5 LX 5 LS 32.23 5LX 5LS 36.71 5L 5LX 5LS 41.17 5L5LX5LS 45.61 5L 5LX 5LS 50.17 5L5LX5LS 54.57 5L 5LX 5LS 58.94 5 LX 5 LS 63,44 5L 5LX 5LS 67.78 5LX 5LS 72.09 5L 5LX 5LS 80.66 5L 5LX 5LS 85.05 89.28 5L 5LX 5LS 97.81 5L5LX5LS
106.13 5L 5LX 5LS 114.37 5L5LX5LS 122.65 5L 5LX 5LS 130.85 5L 5LX 5LS 150.79 170.21 189.11 256.32 269.50 277.25 307.05
31.75 5L 5LX 5LS 34.25 5L 5LX 5LS 36.91 5L 5LX 5LS 42.05 5L 5LX 5LX 47.17 5L 5LX 5LS 52.27 5L 5LX 5LS 57.52 5L5LX5LS 62.58 5L 5LX 5LS 67.62 5LX 5LS 72.80 5L5LX5LS 77.79 5LX 5LS 82.77 5L 5LX 5LS
XXS
STD
XS
STD
XS
'1077
120 140 160
10
20
30
40
60
80
100 120 140 160
10
20
30
40
323.9 323.9
355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6
28.58 33.32
4.78 5.16 5.33 5.56 6.35 7.14 7.92 8.74 9.53
10.31 11.13 11.91 12.70 14.27 15.09 15.88 17,48 19.05 20.62 22.23 23.83 27.79 31.75 35.71 50.80 53.98 55.88 63.50
208.14 238.76
41.35 44.59 46.04 47.99 54.69 61.35 67.90----
74.76 81.33 87.79 94.55
100.94 107.39 120.11 126.71 133.03 145.75 158.10 170.33 182.75 194.96 224.65 253.56 281. 70 381.83
'401.50 413.01 457.40
406.4 4.78 47.34 406.4 ~16 51~6
406.4 5.56 54.96 . 406.4 6.35 62.64
406.4 7.14 70.30 406.4 '7.92 77.83 406.4 8.74 85.71 406.4 9.53 93.27
406.~.4 ___ 1~0~.3~1~_~1~0~0~.7~0~ __ __ 406.4 11.13 108.49 406.4 11.91 115.86 406.4 12.70 123.30
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/ft
16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16
18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18
20 20 20 20 20
16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000
18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000
20.000 20.000 20.000 20.000 20.000
0.562 0.625 0.656 0.688 0.750 0.812 0.844 0.875 0.938 1.000 1.031 1.062 1.125 1.219 1.438 1.594
0.188 0.219 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0,459 0.500 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.156 1.188 1.250 1.375 1.562 1.781
0.219 0.250 0.281 0.312 0.344
92.66 5L 5LX 5LS 102.63 5L 5LX 5LS 107.50 112.51 5L5LX5LS 122.15 5L 5LX 5LS 131.71 5L 5LX 5LS 136.61 141.34 5L 5LX 5LS 150.89 5L 5LX 5LS 160.20 5L 5LX 5LS 164.82 169.43 5L 5LX 5LS 178.72 5L 5LX 5LS 192.43 223.64 245.25
35.76 5L 5LX 5LS 41.59 5L5LX5LS 47.39 5L 5LX 5LS 53.18 5L5LX5LS 58.94 5L 5LX 5LS 64.87 5L 5LX 5LS 70.59 5L 5LX 5LS 76.29 5LX 5LS .82.15 5L5LX5LS 87.81 5LX 5LS 93.45 5L 5LX 5LS
104.67 5L 5LX 5LS 115.98 5L5LX5LS 127.21 5L 5LX 5LS 138.17 5L 5LX 5LS 149.06 5L 5LX 5LS 160.03 5L 5LX 5LS 170.92 5L 5LX 5LS 181.56 5L 5LX 5LS 192.11 5L 5LX 5LS 202.75 5L 5LX 5LS 207.96 213.31 5L 5LX 5LS 223.61 5L 5LX 5LS 244.14 274.22 308.50
46.27 5L 5LX 5LS 52.73 5L 5LX 5LS 59.18 5L 5LX 5LS 65.60 5L 5LX 5LS 72.21 5L 5LX 5LS
81 Units Identification
Plain Standard ISTD) Outside Wall End Previous
X-strong (XI Schedule Diameter Thickness Mass Status XX-strong IXXS) No. mm mm kg/m
STD
60
80
100
120 140 160
10
20
30
406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4
457 457 457 457 457 457 457 457 457 457
14.27 15.88 16.66 17.48 19.05 20.62 21.44 22.23 23.83 25.40 26.19 26.97 28.58 30.96 36.53 40.49
137.99 152.93 160.12 167.65 181.97 196.16 203.53 210.60 224.82 238.64 245.56 252.35 266.28 286.64 333.19 365.35
4.78 53.31 5.56 61.90 6.35 70.57 7.14 79.21 7.92 87.71 8.74 96.61 9.53 105.16
10.31 113.57 11.13 122.38 11.91 130.72
XS 457 12.70 139.15
1078
'lU 457 __ --'-'4"'.=.27'c---__ '''''5'''5'''.8'''0'---__ _ 457 15.88 172.74 457 17.48 189.46
60 457 19.05 205.74 457 20.62 221.89 457 22.23 238.34
80 457 23.83 254.55 457 25.40 270.34 457 26.97 286.00 457 28.58 301.94
100 457 29.36 309.62 457 30.18 317.66 457 31.75 332.95
120 457 34.93 363.56 140 457 39.67 408.26 160
10
457
508 508 508 508 508
45.24 459.37
5.56 6.35 7.14 7.92 8.74
68.89 78.55 88.19 97.67
107.60
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI B36.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units 51 Units
Plain Identification
Plain I nch Outside Wall End Standard (STD) OutSide Wall End Previous
Nominal Diameter Thickness Weight API Specs
X-strong (X) Schedule Diameter Thickness Mass Status Size in. . in. Ib/ft XX·strong (XXS) No. mm mm kg/m
20 20.000 0.375 78.60 SL SLX 5 LS STD 20 508 9.53 '117.15 20 20.000 0.406 84.96 SLX SLS S08 10.31 126.S3 20 20.000 0.438 91.S1 SLSLX SLS S08 11.13 136.37 20 20.000 0.469 97.83 S LX S LS S08 11.91 145.70 20 20.000 0.500 104'.13 SL SLX SLS XS 30 508 12.70 155.12
__ ~2~0 __ ~2~0.~0~0~0 __ ~0.~S~627-~1~1~6~.6~7_~S~L~S~L~X~S=LS~ ________ ~ __ ~S.08 ___ ~1~4.~2~7--~1~73~.~74~ __ _ 20 20.000 0.S94 123.11 40 508 15.09 183.42 20 20.000 0.625 129.33 SL SLX SLS 508 lS.88 192.71 20 20.000 0.688 141.90 SL SLX SLS 508 17.48 211.44 20 20.000 0.750 154.19 SL SLX SLS 508 19.05 229.70 20 20.000 0.812166.40 SLSLXSLS 60' 508 20.62 247.83 20 20.000 0.875 178.72 SL SLX SLS 508 22.23 266.29 20 20.000 0.938 190.96 SL SLX SLS 508 23.83 284.52 20 20.000 1.000 202.92 SL SLX SLS 508 25.40 302.28 20 20.000 1.031208.87 80 508 26.19 311.17 20 20.000 1.062 214.80 SL SLX SLS 508 26.97 319.92 20 20.000 1.12S 226.78 SL SLX SLS 508 28.58 337.89 20 20.000 1.188 238.68 SL SLX SLS 508 30.18 355.61 20 20.000 1.250 250.31 SL SLX SLS 508 31.75 372.88 20 20.000 1.281 256.10 100 508 32.54 381.53 20 20.000 1.312 261.86 SL SLX SLS 508 33.32 390.03
--"-20:--....::.20"'."'0~0·0:---1;.:.~37="5:---,:2:;:.73;.51 5L SLX 5 LS:------------.,:S:-=0"'8--~3"'4"'.::'.93"----=40"'7::.;.;:;49:-----
20 20.000 1.500 296.37 120 508 38.10 441.d9 20 20.000 1.750 341.09 140 508 44.45 508.11
--;:.20:c----;020"'.~00;;:0:c---::-1.96;o9--..;3:;:7;;9c:.l;::7:------~---~~-------:1 60-'--508 50,01 564.81
22 22.000 . 0.219 50.94 5L 5LX 5LS. 559 5:56 75.88" 22 22.000 0.250 58.07 SL SLX 5LS 10 559 6.35 86.54 22 22.000 0.281 65.18 SLSLX5LS 559 7.14 97.17 22 22.000 0.312 72.27 SL SLX SLS SS9 7.92 107.63 22 22.000 0.344 79.56 SL SLX SLS 559 8.74 118.60 22 22.000 0.375 86.61 SL SLX SLS STD 20 559 9.53 129.13
-2"'2:----:2"'2--:.0"'O-O:O---,OAo6 93.63 SLX SLS 559 10.31 139.50 c
22 22.000 0.438 100.86 SL SLX SLS 559 ":13 150.37 22 22.000 0.469 107.85 SLX SLS 559 11.91 160.68
-2~2:---722~.-O:OO~0:--~0~.S~0~0:-~17147.~8~1- SL5=LX~S~L~S---~X~S~----~3~0---=SS"'9:--~1~2.~7~0-----1--:7~1--:.0:-;;9~----
22 22.000 0.562 128.67 SL SLX SLS 559 14.27 191.69 22 22.000 0.62S 142.68 SL SLX SLS 559 15.88 212.69 22 22.000 0.688 156.60 SL SLX SLS S59 17.48 233.43 22 22.000 0.7S0 170.21 SL SLX SLS S59 19.05 2S3.65 22 22:000 0.812 183.7S SL SLX 5LS . SS9 20.62 273.76 22 22.000 0.87S 197.41 SL 5LX 5LS 60 SS9 22.23 294.25 22 22.000 0.938 211.00 SL5LX SLS 559 23.83 314.49 22 22.000 1.000 224.28 SL SLX SLS 559 25.40 334.23 22 22.000 1.062 237.48 SL 5LX SLS SS9 26.97 353.84 22 22.000 1.12S 250.81 5L SLX SLS 80 559 28.58 373.83 22 22.000 1.188 264.06 5L SLX 5LS SS9 30.18 393.S7 22 22.000 1.2S0 277,01 SLSLX SLS 559 31.75 412.81 22 22.000 1.312 289.88 SL SLX SLS SS9 33.32 431.94 22 22.000 1.37S 302.88 SL SLX S LS 100 5S9 34.93 4S1.42
1079
AMERICAN NATIONAL STANDARD WELDED. AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 DimensiQns and Weights Qf Welded and S~amless Wrought Steel Pipe (Continued)
IflCh Units SI Units
Plain Identification
Plain Inch Outside Wall End Standard (STDI Outside Wall End Previous
Nominal Diameter Ttlickness Weight API X·strong (Xl Schedule Diameter Thickness Mass Status Size in. in. Ib/ft Specs XX·strong (XXSI No. mm mm kg/m
22 22.000 1,438 31S.79 SL SLX SLS SS9 36.S3 470.66 22 22.000 1.S00 328.'-1 SL SLX SLS SS9 38.10 489,41 22 22.000 1.62S 3S3.61 120 559 41.28 527.02 22 22.000 1.87S 403.00 140 559 47.63 600.63 22 22.000 2.125 4S1.06 160 559 S3.98 672.26
'24 24.000 0.2S0 63.41 SL SLX SLS 10 610 ii.35 94.53 24 24.000 0.281 71.18 SL SLX SLS 610 7.14 106.15 C
24 24.000 0.312 78.93 SL SLX 5LS 610 7.92 117.59 24 24.000 0.344 86.91 SL SLX SLS 610 8.74 129.59 24 24.000 0.37S 94.62 SL SLX 5LS STD 20 610 9.S3 141.12 24 24.000 0,406 102.31 SLX SLS 610 10.31 1S2.47 24 24.000 0,438 110.22 5L SLX SLS 610 11.13 164.37 24 24.000 0.4S9 117.86 SLX SLS 610 11.91 175.66 24 24.000 O.SOO 12S.49 SL SLX SLS XS 610 12.70 187.06 24 24.000 0.S62 14Q.68 SL SLX 5LS 30 610 14.27 209.64 24 24.000 0.625 156.03 5L 5LX 5LS 610 15.88 232.66 24 24.000 0.688 171.29 5L 5LX SLS 40 610 17.48 255.41 24 24.000 0.750 186.23 5L 5LX 5LS 610 19.05 277.61 24 24.000 0.812 201.09 5L 5LX 5LS 610 20.62 299.69 24 24.000 0.875 216.10 SL 5LX 5LS 610 22.23 322.21 24 24.000 0.938 23'1.03 5L 5LX 5LS 610 23.83 344.46 24 24.000 0.969 238.35 60 610 24.61 35S.26 24 24.000 1.000 24S.64 SL SLX SLS 610 2S,40 366.17 24 24.000 1.062 260.17 5L 5LX SLS 610 26.97 ,'387.76 24 24.000 1.12S 274.84 SL SLX SLS 610 28.58 409.77 24 24.000 1.188 289,44 SL 5LX SLS 610 30.18 431.S2 24 24.000 1.219 296.S8 80 610 30.96 442.08 24 24.000 1.2S0 303.71 SL SLX SLS 610 31.7S 4S2.74 24 24.000 1.312 317.91 SL SLX SLS 610 33.32 473.84 24 24.000 1.37S 332.25 SL SLX SLS 610 34.93 49S.35 24 2,4.000 1.438 346.S0 SL SLX 5LS 61 0 36.53 S16.80 24 24.000 1.500 360.4S SL 5LX SLS 610 38.10 S37.33 24 24.000 1,S31 367.39 100 610 38.89 547.71 24 24.000 l.S62 374.31 5L 5LX 5LS 610 39.67 SS7,43 24 24.000 1.812 429.39 120 610 46.02 640.03 24 24.000 2.062 483.12 140 610 52.37 720.15 24 24.000 2.344 542.13 160 610 S9.S4 808.22
26 26.000 0.250 68.7S 5L 5LX SLS 660 6.3S 102.36 26 26.000 0.281 77.18 SL 5LX SLS 660 7.14 114.9S
'26 26.000 0.312 8S.60 SL 5LX SLS 10 660 7.92 127.36 26 26.000 0.344 94.26 SL SLX SLS 660 8.74 140.37 26 26.000 0.375 102.63 SL SLX SLS STD 660 9.53 152.87 26 26.000 0,406 110.98 SLX SLS 660 10.31 16S.18 26 26.000 0.438 119.57 SL SLX SLS 660 11.13 178.09 26 26000 0.469 127.88 SLX SLS 660 11.91 190.34 26 26.000 O.SOO 136.17 5L SLX SLS XS 20 660 12.70 202.72 26 26.000 0.S62 1S2.68 SL 5LX 5LS 660 14.27 227.23 26 26.000 0.62S 169.38 SL 5LX 5LS 660 1S.88 2S2.24
1080
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. l!l/ft
26 26 26 26 26 26
28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
26.000 26.000 26.000 26.000 26.000 26.000
28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000
0.688 0.750 0.812 0.875 0.938 1.000
0.250 0.281 0.312 0.344 0.375 00406 00438 00469 0.500 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000
185.99 5L 5LX 5LS 202.25 5L 5LX 5LS 218.43 5L 5LX 5LS 234.79 5L 5LX 5LS 251.07 5L 5LX 5LS 267.00 5L5LX5LS
74.09 5L 5LX 5LS 83.19 5L5LX5LS 92.26 5L 5LX 5LS
101.61 5LX 5LS 110.64 5L5LX5LS 119.65 5LX 5LS 128.93 5L 5LX 5LS 137.90 5LX 5LS 146.85 5L 5LX 5LS 164.69 5L5LX5LS 182.73 5L 5LX 5LS 200.68 5L 5LX 5LS 218.27 5L5LX5LS 235.78 5L5LX5LS 253048 5L 5LX 5LS 271.10 5L5LX5LS 288.36 5L 5LX 5LS
SI Units Identification
Standard (STOI Outside Wall X-strong (X) Schedule Diameter Thickness
XX·strong (XXSI No. mm mm
10
STO
XS 20
30
660 660 660 660 660 660
711 ·711 711 711 711 711 711 711 711 711 711 711 711 711 711 711 711
17.48 19.05 20.62 22.23 23.83 25.40
6.35 7.14 7.92 8.74 9.53
10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40
Plain End Previous Mass Status kg/m
276.96 301.1 0 325.12 349.62 373.84 397.49
110.34 123.93 137.32 151.36 164.85 178.15 192.09 205.32 218.69 245.18 271.21 298.95 325.06 351.05 377.58 403.81 429.44
30 30.000 0.250 79043 5L 5LX 5LS 762 6.35 118.33 30 30.000 0.281 89.19 5L5LX 5LS 762 7.14 132.91 30 30.000 0.312 98.93 5L 5LX 5LS 10 762 7.92 147.28 30 30.000 0.344 108.95 5LX 5LS 762 8.74 162.35 30 30.000 0.375 118.65 5L 5LX 5LS STO 762 9.53 176.84 30 30.000 00406 128.32 5 LX 5 LS 762 10.31 191.1 1 30 30.000 00438 138.29 5L 5LX 5LS 762 11.13 206.09 30 30.000 00469 147.92 5LX 5LS 762 11.91 220.30 30 30.000 0.500 157.53 5L 5LX 5LS XS 20 762 12.70 234.67 30 30.000 0.562 176.69 5L 5LX 5LS . 762 14.27 263.12 30 30.000 0.625 196.08 5L 5LX 5LS 30 762 15.88 292.18 30 30.000 0.688 215.38 5L 5LX 5LS 762 17048 320.93 30 30.000 0.750 234.29 5L 5LX 5LS 762 19.05 349.02 30 30.000 0.812 253.12 5L 5LX 5LS 762 20.62 376.98
_-=3~0 __ ..;3:;0::.:.0:;0~0 __ ::0.~8",75~---:2:::7~2",. 1:-;7_.-o57'-L-::5"'L.,-;x..,5,.,L'''S------------ 762 22.23 405.54 30 30.000 0.938 291.14 5L 5LX 5LS 762---23.83·--4:;:3"'3;:.7"'8':-----30 30.000 1.000 309.72 5L 5LX 5LS 762 25040' 461.38
_~30~-__::3~0"'.0~0~0--1~.~06~2~__::3~2~8."'2~2-_;5L~5~L~X~5~LS~-----------~7~6~2--~2~6~.9~7--~478::8.~8~5-~N~-30 30.000 1.125 346.93 5L 5LX 5LS 762 28.58 516.90 N 30 30.000 1.188 365.56 5L 5LX 5LS 762 30.18 544.65 N 30 30.000 1.250 383.81 5L 5LX 5LS ~62 31.75 571.75 N
32 32 32
32.000 32.000 32.000
0.250 0.281 0.312
84.77 5L 5LX 5LS 95.19 5L 5LX 5LS
105.59 5L5LX5LS 10.
1081
813 813 813
6.35 7.14 7.92
126.31 141.89 157.24
AMERICAN NATIONAL STANDARD . .'
WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI B36.10-1~79
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/tt
32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
34 34 34 34 34 34 24 34 34 34 34 34 34 34 34 34 34 34 34 34 34
36 36 36 36 36 36 36 36 36
32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.600 32.000 32.000
34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34'.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000
36.000 36.000 36.000 36.000 3Q.000 36.000 36.000 36.000 36.000
0.344 0.375 00406 0.438 00469 0,500 0.562 0.62S 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.12S 1.188 1.2S0
116.30 5LX5LS 126.66 5L 5LX 5LS 136.99 5LX 5LS 147.64 5L 5LX 5LS 157.94 5LX 5LS 168.21 5L 5LX 5LS 188.70 5L SLX 5LS 209043 5L 5LX 5LS 230.08 SL SLX 5LS 250.31 5L 5LX 5LS 270.47 5L SLX SLS 290.86 SL 5LX 5LS 311.17 SL5LX5LS 331.08 SL 5LX 5LS 350.90 5L 5LX SLS 370.96 SL SLX SLS 390.94 5L 5LX 5LS 410.S1 SL SLX SLS
0.250 90.11 5L SLX SLS 0.281 101.19 SL SLX SLS 0.312 112.2S SLSLXSLS 0.344' 123.6S SLX SLS 0.37S 134.67 SL 5LX SLS 0.406 0.438 0.469 O.SOO 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250
0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.469 O.SOO
14S.67 SLX SLS 157.00 5L SLX 5LS 167.9S SLX 5LS 178.89 5L 5LX 5LS 200.70 SL 5LX 5LS 222.78 5L 5LX SLS 244.77 5L 5LX SLS 266.33 5L 5LX SLS 287.81 5L SLX SLS 309.55 SL 5LX SLS 331.21 5L 5LX SLS 352.44 5L 5LX SLS 373.59 SL 5LX SLS 394.99 5L 5LX SLS 416.31 5L5LXSLS 437.21 5L SLX SLS
9S.45 SL 5LX 5LS 107.20 SL 5LX SLS 118.92 5LSLXSLS 131.00 5LX 5LS 142.68 5L 5LX 5LS 154.34 5LX SLS 166.3S 5L SLX SLS 177.97 SLX SLS 189.S7 SL SLX SLS
81 Units Identification
Plain Standard (STD) Outside Wall End Previous
X-strong (Xl Schedule Diameter Thickness Mass Status XX-strong (XXS) No. mm mm kg/m
STD
XS
STD
XS
STD
XS
1082
20
30 40
10
20
30 40
10
20
813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813
864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864
914 914 914 914 914 914 914 914 914
8.74 9.53
10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.S8 30.18 31.75
6.35 7.14 7.92 8.74 9.53
10.31 11.13 11.91 12.70 14.27 lS.88 17.48 19.0S 20.62 22.23 23.83 2S.40 26.97 28.S8 30.18 31.75
173.34 188.82 204.08 220.08 235.28 250.64 281.07 312.15 342.91 372.98 402.92 433.49 463.7S 493.32 S22.77 SS2.8S S82.61 611.68
134.30 lS0.87 167.20 184.33 200.31 217.0S 234.08 2S0.26 266.61 299.02 332.12 364.90 396.93 428.8S 461.4S 493.72 S2S.27 556.69 588.79 620.56 651.61
6.35 142.13 7.14 159.67
N N N
N N N N
7.92;.-_-71,::76='."'96;-__ _ 8.74 19S.11 9.S3 212.S6
10.31 229.76 11.13 247.31 11.91 264.94 12.70 282.27
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain I nch Outside Wall End
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/ft
36 36 36 36 36 36 36 36 36 36 36 36
38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38
40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000
38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000
.38.000 38.000 38.000
40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000
0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250
212.70 5L 5LX 5LS 236.13 5L5LX5LS 259.47 5L 5LX 5LS 282.35 5L 5LX 5LS 305.16 5L 5LX 5LS 328.24 5L 5LX 5LS 351.25 5L 5LX 5LS 373.80 5L 5LX 5LS 396.27 5L 5LX 5LS 419.02 5L 5LX 5LS 441.69 5L5LX5LS 463.91 5L 5LX 5LS
0.312 125.58 5L5LX5LS 0.344 138.35 5L 5LX 5LS 0.375 150.69 5L5LX5LS 0.406 163.01 5 L 5 LX 5 LS 0.438 175.71 5L 5LX 5LS 0.469, 187.99 5L 5LX 5LS 0.500 200.25 5L 5LX 5LS 0.562 224.71 5L 5LX 5LS 0.625 249.48 5L 5LX 5LS 0.688 274.16 5L5LX5LS 0.750 298.37 5L 5LX 5LS 0.812 322.50 5L 5LX 5LS 0.875 346.93 5L 5LX 5LS 0.938 371.28 5L 5LX 5LS 1.000 .395.16 5L5LX5LS 1.062 418.96 5L 5LX 5LS 1.125 '443.05 5L5LX5LS 1.188 467.06 5L 5LX 5LS 1.250 490.61 5 L 5 LX 5 LS
0.312 0.344 0.375 0.406 0.438 0.469 0.500 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125
132.25 5L 5LX 5LS 145.69 5L 5LX 5LS 158.70 5L 5LX 5LS 171.68 5L 5LX 5LS 185.06 5L 5LX 5LS 198.D1 5L 5LX 5LS 210.93 5L 5LX 5LS 236.71 5L 5LX 5LS 262.83 5L 5LX 5LS 288.86 5L 5LX 5LS 314.39 5L 5LX 5LS 339.84 5L 5LX 5LS 365.62 5L 5LX 5LS 391.32 5L 5LX 5LS 416.52 5L 5LX 5LS 441.64 5L5LX5LS 467.08 5L 5LX 5LS
SI Units Identification
St;ndard (STO) Outside Wall X·strong (X) Schedule Diameter Thickness
XX·strong (XXS) No. mm mm
30
40
STO
XS
STO
XS
1083
914 914 914 914 914 914 914 914 914 914 914 914
965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965
1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016
. 1016
1016 1016
14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
• 7.92 8.74 9.53
10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
7.92 8.74 9.53
10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58
Plain End Previous
Mass Status kg/m
316.11 351.70 386.45 420.42 454.27 488.86 523.11 556.59 589.95 624.03 657.77 690.76
186.92 206.10 224.54 242.72 261.80 279.92 298.24 334.56 371.68 408.43 444.38 480.21 516.82 553.08 588.53 623.87 659:97 695.73 730.69
196.89 217.09 236.53 255.69 275.80 294.90 314.22 352.51 391.65 430.42 468.34 506.14 544.78 583.05 620.48 657.78 695.92
N N N N
N N N N
N N
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and:,V'ieights ,o~ Welded and Seamless Wrought :iteel Pipe (Continuec;l)
Inch U,nits
Plain Inch Outside Wall ,End
Nominal Diameter Thickness Weight, API Specs Size in. in. Ib/ft
40 40
42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42
44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44
46 46 46 46 46 46 46 46 46
40.000 40.000
42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42·000
A4.000 44.090 44.000 44.000 44.000 44.000 44.000 44.000 44.000 4.4.000 44.000 44.000 44.000 44.000 44.000 44.000 44.000 44.000
46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000
1.188 1.2S0
0.344 0.37S 0.406 0.438 0.469 O.SOO 0.562 0.62S
.0.688 0.7S0 0.812
.0.87S 0.938 1.000 1.062 1.12S 1.188 1.2S0
0.344 0.375 0.406 0.438 0,4S9 O.SOO 0.S62 0.62S 0.688 0,7S0 0.812 0.87S 0.938 1.000 1.062 1.125
·,.188 1.2S0
0.344 0.37S 0.406 0,438 0,4S9 O.SOO 0.562 0.625 0.688
492.44 SL SLX SLS S17,31 SL SLX SLS
153.04 SL SLX SLS 166.71 5L 5LX SLS 180.35 5L 5LX 5LS 194.42 SL 5LX SLS 208,03 SL 5LX SLS 221.61 5L 5LX 5LS 248.72 SL SLX SLS 276.18 303.5S 330.41 3S7.19 384.31 411.3S 437.88 4,64.32 491.11 S17.82 S44.01
SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SLSLXSLS SLSLX SLS SL SLX SLS SL SLX SLS
160.39 SL SLX SLS 174.72 SL SLX 5LS 189.03 SL 5LX 5LS 203.78 SL SLX SLS 218.04 232.29 260.72 289.S3 318.2S 346.43 374.S3 403.00 ~31.39 4S9.24 487.01
SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS
S15.14 SL SLX SLS 543.19 SL SLX SLS S70.71 SL SLX SLS
167.74 182.73 197.70 213.13
. 228.06 242.97 272.73 302.88 332.95
SL SLX SLS SL SLX 5LS SL SLX SLS 5L 5LX SLS SL SLX SLS SL SLX SLS 5L 5LX SLS SL eLX 5LS SL SLX SLS
81 Units I~entifi,?ation
Standard (STD) Outside - Wall X-strong (Xi) Schedule Diameter Thickness
XX·strong (X1(S) No. mm rnm
STD
XS
STD
XS
STD
XS
1084
1016. 1016
1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 10E!7
1118 ·1118 1118 1118 1118 1118 1118 1118 1118 1118 1118 11.18 1118 1118 1118. 1118 1118 1118
1168 1168 1168 1168 1168 1168 1168 1168 1168
30.18 31.75
8.74 9.53
10.31 11.13 11.91 12.70 14.27 1S.88 17.48 19.0S 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
8.74 9.53
10.31 11-13 11.91 12.70 14.27 1S.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
8.74 9.S3
10.31 11.13 11.91 12.70 .14.27 1S.88 17,48
Plain End Previous
Mass Staw~, kg/m
733.68 770.62
228.09 248.52 268.66 289.80 309.88 330.19 370.4S 411.62 452.40 492.30 S32.07 S72. 73 613.02 652.42 691.70 731,86 771.64 810.55
239.08 260,50 281.62 303,80 ,324.80 G46.16 388.40 431.S9 474.37 S16.26 SS8.00 600.69 642.99 684.37 725.62 767.80 809.60 850.48
249.85 272.25 294.34 317.52 339.S4 3S1,82 406.00 451.17 49S.94
N N
N N N N
N N N
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall end
Nominal Diameter Thickness Weight API Specs Size in. in. Ib/ft
46 46 46 46 46 46 46 46 46
48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48
46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000
48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000
0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250
0.344 0.375 0.406 0.438 0.469 0.500 0.562 0.625 0.688 0.7S0 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250
362.45 5L 5LX 5LS 391.88 5L 5LS 5LS 421.69 5L 5LX 5LS 451.42 5L 5LX 5LS 480.60 5L 5LX 5LS 509.69 5L 5LX 5LS 539.17 SL SLX 5LS 568.S7 5L 5LX 5LS 597.41 5L 5LX 5LS
175.08 5L 5LX 5LS 190.74 5L 5LX 5LS 206.37 5L 5LX 5LS 222.49 5L 5LX 5LS 238.08 SL 5LX 5LS 253.65 5L 5LX 5LS 284.73 5L 5LX 5LS 316.23 SL SLX SLS 374.64 SL 5LX SLS 378.47 5LSLXSLS 409.22 SL 5LX 5LS 440.38 SL SLX SLS 471.46 SL 5LX 5LS 501.96 5L SLX SLS S32.38 5L 5LX 5LS 563.20 5L 5LX 5LS 593.94 5L 5LX 5LS 624.11 5L5LX5LS
81 Units Identification
Standard (STD) Outside Wall. X·strong (X) Schedule Diameter Thickness
XX·strong (XXS) No. mm mm
STD
XS
1168 1168 1168 1168 1168 1168 1168 1168 1168
1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219
19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
8.74 9.53
10.31 11.13 11.91 12.70 14.27 lS.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
Plain End Previous
Mass Status k~im
539.76 583.43 628.10 672.37 715.68 758.88 803.04 846.81 889.63
260.85 284.24 307.30 331.S2 354.52 377.79 423.94 471.14 517.92 563.70 609.36 656.06 702.34 747.63 _
N N N N
792.80 N 838.99 N 884.77 N 929.56 N
52 52.000 0.375 206.76 5L 5LX 5LS 132" 9.53 308.21 N S2 52.000 0.406 223.72 5L 5LX 5LS 1321 10.31 333.24 iii
_:::S2~ __ 5:::2~.0~0~0;_--;:0.438c---;2;;:4",1~.2~0--;5:-;:L:.;5~L~X:-:5",L::;Sc-___________ _:_1 ~32~1;_-__:_1_:_1 :.;.1:;3 __ .-;3o;5;::9::.;.5",1:-__:_N,:-_ 52 52,000 0.469 258.115L5LX5LS 1321 11.91 384.48 N 52 52.000 0.500 275.01 SL 5LX 5LS 1321 12.70 409.64 N S2 52.000 0.562 308.74 SL 5LX 5LS 1321 14.27 459.84 N 52 52.000 0.625 342.93 5L 5LX 5LS 1,32" 15.88 511.09 N S2 52.000 0.688 377.03 SL 5LX 5LS 1321 17.48 S61.89 N S2 S2.000 0.7S0 410.S1 SLSLXSLS 1321 19.05 611.62 N 52 52.000 0.812 443.91 5L 5LX 5LS 1321 20.62 661.23 N 52 52,000 0.875 477.76 5L 5LX 5LS 1321 22.23 711.98 N 52 52.000 0.938 511.53 5L 5LX 5LS 1321 23.83 762.28 N 52 52.000 1.000 544.68 ,SL 5LX 5LS 1321 25.40 811.52 N <;2 52.000 1.062 577.75 5L 5LX SLS 1321 26.97 860.63 N 52 52.000 1.125 611.26 5L5LX 5LS 1321 28.58 910.88 N 52 52.000 1.188 644.69 5L 5LX SLS 1321 30.18 g60.68 N 52 52.000 1.250 677.51 5L SLX 5LS 1321' 31.7S 1009.42 N
56 56 56
56.000 56.000 56.000
0.375 0.406 0.438
222.78 5L 5LX 5LS 241.06 5L 5LX 5LS 259.91 5L 5LX 5LS
1085
1422 1422 1422
9.53 10.31 11.13
331.94 r. . 358.91 N 387.24 N
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10.-1979
Table.2 Dimensions and Weights of Welded and Seamless-Wrought Steel Pipe (Continued)
Inch Units 81 Units
Plain Identi.fication
Plain
Inch Outside Wall End Standard (STD) OutsWe Wall End Previous
Nominal Diameter Thickness Weight API. Specs
X-strong (X) Schedule Diameter Thickness Mass Status Size in. In. Ib/ft XX·strong (XXS) No. mm mm kg/m
56 56.000 0.459 278.15 5L 5LX 5LS 56 56.000 0.500 296.37 5L 5LX 5LS
_~56:;-_-;5=-;6~.0=-;0",0 __ ",0.",56:::;2:;---,;.;332.75 5L 5LX 5LS 56 56.000 0.625 369.63 5 L 5 LX 5 LS 56 56.000 0.688 406.42 5L 5LX 5LS 56 56,000 0.750 442.55 5L 5LX 5LS
1422 1422 1422 1422 1422 1422
11.91 414.14 N 12.70 441.37 ·N
14 .. 27.---:4:::9~5'"=3,,.8-~N_ 15.88 550.54 N 17.48 605.43 N 19.05 659.07 N
56 56.000 0.812 478.60 5L 5LX 5LS 1422 20.62 712.59 N 56 56.000 0.875 515.14 5L 5LX 5LS 1422 22.23 767.34 N 56 56'.000 0.938 551.60 5L 5LX 5LS 1422 __ .23.,~~ __ !3.1.:!'3 ___ N_ 56 56.000 1.000 587.40 5L5LX5LS 1422 25.40 875.78 N 56 56.000 1.062 623.12 5L 5LX 5LS 1422 26.97 927.81 N 56 56.000 1.125 659.32 5L 5LX 5LS 1422 28,58 982.06 N
-~56~-~5~6.~0~0~0--71.~1~88~--;6~9"'5~.4~5--;5~L~5L~X~57L~S------------~1422~-~30~.718~-~1~0~35~.~85~-7.N---56 56.000 1.250 730.91 5L 5LX 5LS 1422 31.75 1088.50 N
60 60.000 0.375 238.80 5L 5LX 5LS 1524 60 60.000 0.406 258.40 5L 5LX 5LS 1524 60 60.000 0.438 278.62 5 L 5 LX 5 LS 1524 60 60.000 0.469 298.19 5L 5LX 5LS 1524 6'0 60.000 0.500 317.73 5L 5LX 5LS 1524 60 .60.000 0.562356.76 5L5LX5LS 1524 60 6.0.000 0.625 396.33 5 L 5 LX 5 LS 1524 60 60.000 0.688 435.81 5L 5LX 5Ls 1524 60 60.000 0,750 474.59 5L 5LX 5LS 1524
-~60~~~6~Q.~0~00~---0~;"'8~12~~5~1~3~.2~9-~5~L~5~L~X~5~LS-----------~1~52~4~· 60 60.000 0.875 552.52 5 L 5 LX 5 LS 1524 60 60.000 0.938 591.67 5L 5LX 5LS 1524 60 60.000 1.000 630.12 5L 5LX 5LS 1524 60 60.000 1.062 668.48 5L 5LX 5LS 1524 60 60.000:-__ -'1."'.1'=2~5--_c7:,.:07 .38 5 L 5 LX 5 LS 1524 60 60.000 1.188 746.20 5L 5LX 5LS 1524 60 60.000 1.250 784.31 5L 5LX 5LS 1524
64 64.000 0.375 254.82 5L 5LX 5LS 64 64.000 0.406 275.75 5L 5LX 5LS 64 64.000 . 0.438 297.33 5 L 5 LX 5 LS 64 64.000 0.469 318.22 5L 5LX 5LS 64 64,000 0.500 339.09 5L 5LX 5LS
1626 1626 1626 1626 1626
9.53 355.92 N 10.31 384,85 N 11.13 415.23 N 11.91 444.10 N 12.70 473.31 N 14.27 531.27 N 15·.88 590.58 N 17.48 6.49.40 N
.19.0;;.5~--=7~067'.98 N 20.62 764.45 N 22.23 823.26 N 23.83 881.57 __ N_ 25.40 938.67 N 26.97 995.64 N 28.58 1053 .. 95 N 30.18 1111.76 N 31.75 1168.36 N
9.53 10.31 11.13 11.91 12.70
379.89 410.78 443.23
N N N
_~647--~6~~."=0~00~--0~.~5~62~~3~8~0~.7~6~~5~L~5~LX~57L~S ___________ ~16~§---~~7-64 64.000 0.625 423 .. 03 5L 5LX 5LS 1626 lS.88
474.06 505.26 567.16 630.52
N N N N
64 64;000 0.688 46S.21 5L SLX SLS 1626 17.48 693.36 N
_~647--~6"'~"=;0~0"'0--0~."'7::_50~___c5;_'0~6::;.6~3:_-~5~L~5~LX~57L~S-----------__::16.?§------1~OS- .254 .90 ____ N __ 64 64.000 0.812 547.98 5L 5LX 5LS 1626 20.62 .816.32 N 64 64.000 0'.875 589.90 5L 5LX 5LS 1626 22.23 879.17 N 64 64.000 0.938 631174 5L 5LX 5LS 1626 23.83:-__ ,..,90-:4::,:1-',:. 51 ____ N __ _ 64 64.000 1.000 672.84 5L 5LX 5LS 1626 25.40 1002.56 N 64 64.000. 1.062 713.85 5L5LX 5LS 1626 26.97 1063.48 N 64 64.000 1.125 755M 5L 5LX 5LS 1...6.26 ___ ~~.&IL_..!.1-"'12"'5"'.8"'3'____:..N'___ 64 64.000 1.188 796.95 5L 5LX 5 LS 1626 30.18 1187.67 N 64 64.000 1.250 837.71 5L 5LX 5LS 1626 31.75 1248.23 N
1086
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10-1979
Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued)
Inch Units
Plain Inch Outside Wall End
Nominal Diameter Thickness Weight API Specs Siz8 in. in. Ib/ft
68 68 68 68 68 68 68 68 68 68 68 68 68 68
72 72 72 72 72 72 72 72 72 72 72 72 72
76 76 76 76 76 76 76 76 76 76 76 76 76
80 80 80 80 80 80 80
68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000 68.000
72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000 72.000
76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000 76.000
80.000 80.000 80.000 80.000 80.000 80.000 80.000
0.469 338.26 SL SLX SLS O.SOO 360.4S SL SLX 5LS 0.S62 404.77 SL SLX SLS 0.625 449.73 SL SLX 5LS 0.688 494.60 5 L S LX 5 LS 0.750 S38.67 SL SLX SLS 0.812 582.66 SL SLX SLS 0.87S 627.28 SL SLX 5LS 0.938 671.82 SL SLX 5LS 1.000 71S.S6 SLSLXSLS 1.062 7S9.22 SL SLX 5LS 1.12S 803:S0 SLSLXSLS 1.188 847.70 SL SLX SLS 1.2S0 891.11 SL 5LX 5LS
0.500 381.81 SL SLX SLS 0.562 428.78 0.62S. 476.43
SL SLX SLS SL SLX 5LS
0.688 523.99 SL SLX SLS , SL SLX SLS SL SLX SLS
0.7S0 S70.71 0.812 617.3S 0.87S 664.66 SL SLX SLS
5LSLXSLS 5L SLX SLS
0.938 711.89 1.000 7S8.28 1.062 1.12S 1.188 1.2S0
O.SOO 0.S62 0.62S 0.688 0.7S0 0.812 0.87S 0.938 1.000 1.062 1.12S 1.188 1.2S0
0.S62 0.62S 0.688 0.750 0.812 0.87S 0.938
804.S9 SL SLX 5LS 8S1.S6 SL SLX 5LS 898.4S SL SLX 5LS 944.51 5L SLX 5LS
403.17 SL SLX SLS 4S2.79 SL SLX SLS S03.13 SLSLXSLS SS3.38 SL SLX SLS 602.7S SL SLX SLS 6S2.04 SL SLX SLS 702.04 5L 5LX SLS 7S1.96 SL SLX 5LS 801.00 SL SLX 5LS 849.96 SL SLX 5LS 899.62 SL SLX SLS 949.20 5L 5LX 5LS 997.91 SL SLX SLS
476.80 SL SLX SLS S29.83 SL SLX 5LS S82.77 SL SLX SLS 634.79 SL SLX SLS 686.73 SL SLX 5LS 739.42 SL SLX 5LS 792.03 SL SLX SLS
SI Units Identification
Standard (SrO) Outside Wall X·strong IX) Schedule Diameter Thickness
XX-strong (XXS) No. mm mm
1087
1727 1727 1'727 1727 1727 1727 1727 1727 1727 1727 1727 1727 1727 1727
1829 1829 1829 1829 1829 1829 1829 1829 1829 1829 1829 1829 1829
1930 1930 1930 1930 1930 1930 1930 1930 1930 1930 1930 1930 1930
2032 2032 2032 2032 2032 2032 2032
11.91 12.70 14.27 lS.88 17.48 19.0S' 20.62 22.23 23.83 25.40 26.97
. 28.S8 30.18 31.7S
12.70 14.27 lS.88 17.48 19.0S 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75
12.70 14.27 15.88 17.48 19.0S 20.62 22.23 23.83 2S.40 26.97 28.58 30.18 31.7S
14.27 1S.88 17.48 19.0S 20.62 22.23 23.83
Plain End Previous Mass Status kg/m
S03.72 S36.89 602.71 670.08 736.90 802.35 867.68 934.S4
1000.86 106S.82 1130.66 1197.02 1262.84 1327.30
N N N N N
N N N N N N N N N
S68.83 N 638.60 N 710.02 N 780.87 N 8S0.29 N 919.S4 N 990.46 N
1060.80 N 1129.7~1_--:-;N_ 1198.49 N 1268.91 N 1338.7S N 1407.17 N
600.46 674.14 749.S7 824.40 897.71 970.90
104S.82 1120.16 1192.97 126S.67 1340.09 1413.92 1486.24
710.04 789.51 868.37 94S.63
1022.76 1101.74 1180.10
N N N N N N N N
N N N N N
N N N
N N N N
AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE ANSI 836.10·1979
Table 2 Dimensions and Weights of Welded and S~amless Wrought Steel ~ipe (Continued)
Inch Units SI Units
Plain Identification
Plain Inch Outside Wall End ·Standard (STDI Outside Wall End Previous
Nominal Diameter Thickness Weight API X-strong (XI Schedule Diameter Thickness Mass Status Size in. in. Ib/lt Specs XX-strong (XXSI No. mm mm kg/m
80 80.000 1.000 843.72 5L 5LX 5LS 2032 25.40 1256.86 N 80 80.000 1.062 895.33 5L 5LX 5LS 2032 26.97 1333.50 N 80 80.000 1.125 947.68 5L 5LX 5LS 2032 28.58 1411.97 N 80 80.000 1.188 999.95 5L 5LX 5LS 2032 30.18 1489.83 N 80 80.000 1.250 1051.31 5L 5LX 5LS 2032 31.75 1566.11 N
1088