Annexure IV

SPECIFICATIONS OF EQUIPMENTS FOR CCTV SYSTEM

I Fixed Day/Night IP Box type HD Camera (OUTDOOR Application)- Free issue from BPCL ( Specifications enclosed as Annexure- a)

Application Outdoor (The camera to be used for constant surveillance of critical plant areas, viz. security gate, pump houses, TLF Gantry etc. (Petroleum Oil depots / terminals) . Glare from street lights should not affect video quality at night.

II High Speed Dome type Day/Night IP PTZ Camera (OUTDOOR Application) FEATURES MINIMUM REQUIRED PARAMETERS CAMERA & VIDEO

1 Application Outdoor (The camera to be used for surveillance of plant (Petroleum Oil depots / terminals) area / perimeter). Glare from street lights should not affect video quality at night. Day & Night Operation (Automatic switchover from color mode to Monochrome Mode when the light falls below a certain threshold level)

2 Sensitivity (Minimum Illumination)

1.0 Lux Day Mode (Color)(SENS UP off ) & 0.1 Lux Night Mode (Monochrome) (SENS UP off ) ( Sensitivity shall be measured @ F1.4, IRE-30

3 Image Sensor 1/3” Progressive Scanning CCD/CMOS Color Sensor

4 Lens Varifocal 5 Lens Focal Length 4.7-94 mm

6 IR Cut Filter Automatic removable IR Cut filter 7 Electronic Shutter Digital (Auto / Manual selectable) with Speed of approx. 1 -

1/10,000 second to capture clear picture / video as per specifications

8 Iris Type Auto ( Video drive)

9 Lens Zoom (18X Optical & 10X Digital )

10 Presets 90 with +-0.1° accuracy

11 Programmable Patterns 8 (Eight) including Pan, Tilt & Zoom tour functions 12 Flip Function Auto endless

13 Pan movement 360° (endless) continuous pan rotation 14 Tilt Range 0° to more than 90° vertical

15 Pan Speed Variable between 80°/sec to 0.1°/sec (Adjustable through software, also possible manually)

16 Tilt Speed 0.1 deg. To 40°/sec (Manual operation)

17 Zoom Speed Adjustable

18 Wide Dynamic Range Yes (Min. 50 DB) 19 Television System PAL 20 Video Streaming/ Video

Compression Multiple (3), individually configurable streams in H.264 & Motion JPEG.

21 Auto image stabilizer On/Off (Selectable)

22 Uni -casting & Multicasting feature

Required

23 Aspect Ratio Compatible to HD (16:9) 24 Minimum Resolution (in

Pixels 1920 (V) X 1080 (H) (TRUE HD)

25 Frame Rate 25 fps @ PAL 26 S/N Ratio 50 Db or More 27 Automatic Gain Control

(AGC) On / Off (Selectable)

28 White balance Automatic with Manual Override (2,000° to 10,000°K) 29 Back Light Compensation

(BLC) On/Off (Selectable)

30 Image settings Compression, color, brightness, sharpness, contrast, white balance, exposure control, backlight compensation, exposure zone, automatic back focus, mirroring of images, WDR, dynamic contrast, text & image overlay, privacy mask.

31 Software Interface Web Browser 32 Image Enhancement feature Yes 33 Tilt & Zoom Display On Screen 34 Privacy Zone masking Yes (6 zones) 35 Frame Freezing Yes 36 Auto focus Yes 37 Alarm triggers Intelligent video, external inputs AUDIO

38 Audio streaming Minimum One-Way , uni-Directional transmission of voice.

39 Audio Compression AAC LC 8/16 kHz./G.711 PCM8kHz./G.726 ADPCM8kHz.Configurable bit rate

40 Audio Input/output Built-in microphone or port for connecting External microphone input. Signal Line in / Line out to support audio inputs & outputs. ( Ports required to pick up sound along with video are optional)

NETWORK / Built –in Analytics & SECURITY

41 Security Password Protected access, IP address filtering & user access log facility

42 Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, SNMP v2c/v3, QoS, HTTP, HTTPS, SSH, SSL, SMTP, FTPand 802.1x (EAP). Camera shall support open IP standards.

43 Service Port PAL output

GENERAL

44 Power Source 230 V AC supply shall be made available in the control room. Vendor shall arrange to make necessary cabling from the BPCL provided source to the camera

45 Dome Housing NEMA 4X certified IP-66 rated (Weather & Dust resistant) with an aesthetic appeal. Cast Aluminum (To be suitable for Coastal Environment) In-built sun-shade & heater as applicable for achieving desired performance ( 24/7) Easy cable routing Impact Resistant (IK10++ per EN62262 (50 J) Vandal / Tamper Resistant Make to be same as that of camera. Shock & Vibration Resistant

46 Mounting

Pendant type. As per site conditions. Adjustable head with 360 deg pan, 180 deg tilt. Make to be same as that of the Camera.

47 View Material (Dome Bubble)

Polycarbonate Plastic / Acrylic Plastic / Tempered Glass

48 Connectivity Ethernet (RJ-45 Connector) for 10/100 Mbps speed. 49 Internal Heat Sink Required 50 Mounting Pendant mount / as per site requirement. Make to be same as

that of the camera. 51 Mechanical Adjustment Pan (350°), Tilt (180°) ,Rotate (200°)

52 Operational Temp. 0° to 50° C

53 Operating Humidity 20% to 90% RH (non condensing)

54 Accessories The cost of Camera shall include all the required accessories, connectors etc to connect Camera with Cat-6 Cable & for mounting on the pole. Surge arrestor ( in-built ) or external for power & Ethernet circuits

Certifications & Approved makes

55 Certifications IEC standards viz.IEC 60068-2-6 or as applicable. FCC standards viz.FCC part 15 or as applicable, EN standards viz. EN 55022, 55024 or as applicable, UL or Vds standards viz. UL60950-1 or

as applicable. (Model specific) 56 Application Programming

Interface Camera shall be ONVIF certified with suitable SDK ‘s & API’s to be supplied with the camera

58 License Fees: No license fees shall be payable over & above the rates quoted by the bidder in this tender for operating & accessing cameras as well as for firmware up gradation throughout the contract period including comprehensive AMC period ( 2 + 3 years)

III Video Management Software (Viewing, Recording and Playback Software)

( Type-I locations :32 CAMERAS), Type-II locations : 64 CAMERAS)

1 Software Functional Requirement

The software should allow seamless integration of third party security infrastructure. The Software should be a highly scalable enterprise level solution. It must offer Video Management solution scalable from 1 camera to 16/32/64 cameras as per BOQ. (Minimum).

Shall support IP Cameras & Encoders (for analog camera interface)

The VMS shall be based on open architecture which facilitates integration with other IT systems , Owner supplied free-issue cameras with the help of API (distributed free of charge). Shall be ON/VIF compliant. The system shall allow operation with PC Keyboard, Mouse, CCTV Keyboard.

Shall be able to view single and multiple cameras simultaneously. The software should provide user licenses for at least 5 users per site and camera licenses as per the number of cameras to be installed at site as per bill of material & shall be scalable for 32/64 cameras in future as the case may be. Remote Administration, Monitoring & Management of Video at Plant level.

Facility for exporting the video. Alarm pop ups for the associated cameras. Shall be able to view single and multiple cameras simultaneously. The software should provide user licenses for at least 5 users per site and camera licenses as per the number of cameras to be installed at site as per bill of material & shall be scalable for 32/64 cameras in future.

Remote Administration, Monitoring & Management of Video at Plant level.

Facility for exporting the video / viewing through internet Alarm pop ups for the associated cameras.

2 Platform The software should be compatible with Windows Operation Systems (Windows Server 2003 / Windows Server 2007 / Windows Server 2008)

3 Compatibility The VMS should be built on open standard and shall be compatible with products from industry leading manufacturers.

4 Viewing Logical camera grouping Simultaneous viewing live and recording from various Cameras by multiple users (min. 8 cameras view simultaneously)

Drag and Drop Camera Viewing. Multi camera sequential tours The VMS should have viewing client to enable the feed display on the workstation / remote location. Extended camera viewing on multiple monitors Remote viewing of cameras through internet. Digital zooming feature User friendly PTZ Control functions of PTZ Camera. Support Multiple Video Resolutions (CIF, 2CIF, 4CIF & HD (up to 8 MP))

5 Recording & Retrieval

Should have feature of recording and retrieval of Video and Audio.

Continuous recording, by trigger (motion or alarm), by schedule.

Should support the recording of H.264, MPEG-4 & MJPEG compressions

Should have Configurable recording rate per camera

6 Storage

Multi level storage: should support multilevel storage (live recording on primary disk, archiving on secondary, and so on) should delete video after configurable duration. Distributed , fault tolerant database architecture

7 Video Search

Video smart search on the basis of date, time, event, camera , location & alarm Should have advanced / smart / quick search function

Sorting by camera name & IP Address. Should be able to export searched video to standard video codec (or with video player in case of proprietary format) Quick review of upto 60 minutes of data.

8 Event Management

Register event, associated video and alert operator on screen with audio. Motion detection, sound detection, camera tampering events should be alerted to the operator.

9 Camera Management

Show connection status of cameras, alert operator on screen with audio Manage firmware upgrades, setting IP address. Set camera settings such as brightness, contrast etc.

10 Security User management, password management, user access level management

11 Configurations Various layout configurations (2X2, 3X3 & 4X4)

12 General Features & Specifications

-user-friendly PTZ Controls -Graphic video footprints with real-time PTZ controls -Sensor management tools, Alarm management options and data editing. -Enhanced displays for video forensics and access to video archive systems

-Supports JPEG or BMP or GIF data input -Capable of managing an assigned area of interest -Capable of ingesting video and sensor inputs into an open architecture format, onto one screen -Provides a monitoring capability of the video/sensor Subsystem, to be relayed to the key operations centre. -Provides a multiple perspective geographic display of site locations with site specific surveillance information including sensor locations and alarm conditions. -Provides a remote ability to set and/or modify Operational characteristics of surveillance devices and Storage -On line control of Pan/Tilt/Zoom (PTZ) cameras, sensors -Ability to record and retrieve stored video -Integrated-alarm visualization rule and device control displays in either a single or double monitor format -Ability to slue PTZ cameras to alarm generated areas -Capability of Real time analysis of connected cameras to detect abnormal activity and security threats. -Capability to filter large amounts of video and support display of time line, customizable site Map, Live Video, Video playback, Integrated site map, Remote live view,Multi site capability, Event based recording all over local LAN -Ability to deploy the alarm components on PC Computer servers or on remote, ruggedized, externally mountable, stand alone platforms. -Camera obstructed should activate alarm if the field of view is obstructed. -Cord cut-will alarm if the video signal is lost. -Hardware alarm input – should be able to receive signals from external devices through alarm I/O and act accordingly -Software should be an open IP surveillance product, enabling simultaneous digital video recording from network,mega pixel and analog device, intelligent video analysis and remote access to live and recorded images from any networked computer. -Software should allow to add, edit, delete or disable and enable policies for video management. -Option of remote viewing over handheld moblie set (3G) to keep updated while in the field. -Software should be jointly and simultaneously able to manage video analytics and video management as one product. -Software should be able to store video to local harddisk, a RAID configuration or even a storage-area network (SAN). -Software should support display of time line, customizable site Map, Live Video, Video playback, Integrated site map, Remote live view, Multi site capability, Encryption, Event based recording.

-Option of on screen digital video tracking & digital zoom on tracked area. -Option of on screen object follow thru within tracked area -Management of recorded video with on screen time graph and multiple color coded event indicators for selective and simultaneous view of alarm and non alarm situations for quick viewing -User friendly and time graph based selection for playback and instant archival of video events on external media -On selection of specific area on video with specific date and time period, instant retrievals of all past events/activities at this selected area should be retrieved and viewed instantly as a single video/movie clip -Insertion and deletion of Cameras -Software forensics analyzer shall allow the user to quickly search for and detect security events that occurred in the past. Example includes –

- Scan days and weeks of pre recorded video within minutes - Locate and extract information about potential security breaches - Allow users to run regular quaries to detect patterns - Allow users to apply any rule to any amount of collected or stored

video data -Software shall provide the ability to set up security rules for surveillance cameras. -Software shall be able to create rules and responses based on digital or contact closure input events from external devices, such as critical infrastructure-related events, Network connection failures, Fatal errors, Hard Disk failures, Software service down, Video encoder failures, Security-related events, Digital input pin change, Video lost, On screen alarms, Maintenance related events, User event notification using SMTP (Mail) -Software shall be able to perform the following tasks simultaneously: a. Digitizing and compressing video b. Writing video to files on local hard disk and maintaining an accurate index of the stored video file c. Deleting older video files as needed, to free up space to record newer video files d. Selectively transferring recorded video to long term storage media -Software shall be capable of managing online storage that is, online video shall be available for immediate playback. Storage shall be intelligently managed so that the video that is most likely to be requested by users will be retained online. -Generating and managing system logs and audit reports, define the reporting level for system events generated by various services, Filtering log files and events, system availability -Updates as & when required during contract period shall be done with out additional cost. Original licensed copy of the software shall be supplied along with the system. - Uptime of CCTV System should be available in a module. The same to be available based on Query as daily, weekly, Monthly, Quarterly & yearly. Uptime of CCTV system is considered as 100 % when all the cameras (“n” no.s) & system functionality are operational. If one camera is down &

balance cameras (n-1) are available fully with all system functionalities, uptime shall be (((n-1)/n )*100 ) %.

13 Certifications Soft ware shall be ONVIF compliant

14 Approved Makes

Nice, Mirasys, Milestone, Vicon, Honeywell, Dvtel, Verint , Axis, Genetic, Mindtree . Vendor can offer any other reputed make software provided bidder shall submit Proven Track Record from the user at least one year from tender due date along with the bid and it is subject to BPCL approval.

IV Video Management / Video Analytics / Network Video recording Server - For type-1

locations having maximum 36 cameras FEATURES MINIMUM REQUIRED PARAMETERS

General requirement

Should be compatible for loading video analytic software( supporting ON-VIF protocol) from any third pary. Also shall support in-built analytics of any ON/VIF compliant camera, issued with this tender or to be installed at later date during Comprehensive AMC period

1 Processor Type Intel Quad Core 2.0 GHz- Xeon processor ( 3 GB Ram)

2 Hyper Threading Technology support Yes (2 threads / core)

3 Turbo boost Technology support Yes

4 Internal L3 Cache 12MB 5 BIOS Type Unified Extensible Firmware Interface (UEFI) 6 Standard Memory 8 GB expandable up to 16 GB 7 DIMM Slots 11 8 Memory Access Speed 1066MHz

9 Memory Mirroring Support Yes / 1 channel (2 slots per processor) active, 1 spare, 1 unused

10 Storage Technology Hot-swap SAS/SATA, simple-swap SATA 11 No of HDD Bays 8 ( hot-swap, with internal backup drive)

12 Hard Disk Capacity 16 TB ( Combination of min.2 TB (Internal) & min. 14 TB external ( with provision of adding additional 8 TB later & provision for taking back-ups)

13 Drive Capacity Supported 250GB, 500GB, 1TB, 2TB

14 RAID Supports RAID 5 configuration 15 No of Video Ports Dual 16 Video Memory 16 MB DDR3 SDRAM

17 Maximum video resolutions 1980x1080 at 50Hz (32 bits)

18 Gigabit Ethernet controller Intel 82575 19 No of Gigabit Ports 2

20 No of USB Ports 5

21 Integrated systems management controller

Yes (IMM)

22 Video Graphics Card

NVIDIA Quadro 600,CUDA Cores: 96,Total Frame Buffer: 1 GB DDR3,Memory Interface: 128 bit,Memory Bandwidth: 25.6GB/s

Display Port: 1,Maximum Display resolution: 2560 x 1600 Shader Model: 5.0,OpenGL: 4.0,Microsoft Direct X: 11 NVIDIA CUDA Architecture: Yes, Mosaic Technology: Yes Display Management Software: Yes, FSAA (Max): 64 x

23 Optional systems management adapter Virtual Media Key (optional)

24 Predictive Failure Analysis (PFA) support Memory, HDDs, and the onboard battery

25 No of Power Supplies 1 +1 ( redundant) 26 No of cooling fans 4 (As per the server design)

27 Operating System Windows Server 2003 / Windows Server 2007 / Windows Server 2008, should be compatible with the supplied video management software and analytics.

28 Anti Virus Norton (Latest) or approved equivalent with free upgrades till validity of contract including comprehensive AMC period

29 Approved makes IBM, HP, Dell

IV Video Management / Video Analytics / Network Video recording Server (Type-2 locations having maximum 72 cameras)

FEATURES MINIMUM REQUIRED PARAMETERS

General requirement

Should be compatible for loading video analytic software( supporting ON-VIF protocol) from any third pary. Also shall support in-built analytics of any ON/VIF compliant camera, issued with this tender or to be installed at later date during Comprehensive AMC period

1 Processor Type Intel Quad Core 2.4 GHz- Xeon processor ( 4 GB Ram)

2 Hyper Threading Technology support Yes (2 threads / core)

3 Turbo boost Technology support Yes

4 Internal L3 Cache 12MB 5 BIOS Type Unified Extensible Firmware Interface (UEFI) 6 Standard Memory 8 GB expandable up to 16 GB 7 DIMM Slots 11 8 Memory Access Speed 1066MHz 9 Memory Mirroring Support Yes / 1 channel (2 slots per processor) active, 1 spare, 1 unused

10 Storage Technology Hot-swap SAS/SATA, simple-swap SATA 11 No of HDD Bays 8 ( hot-swap, with internal backup drive)

12 Hard Disk Capacity 16 TB ( Combination of min.2 TB (Internal) & min. 14 TB external ( with provision of adding additional 16 TB later & provision for taking back-ups)

13 Drive Capacity Supported 250GB, 500GB, 1TB, 2TB 14 RAID Supports RAID 5 configuration 15 No of Video Ports Dual 16 Video Memory 16 MB DDR3 SDRAM 17 Maximum video resolutions 1980x1080 at 50Hz (32 bits) 18 Gigabit Ethernet controller Intel 82575 19 No of Gigabit Ports 2 20 No of USB Ports 5

21 Integrated systems management controller Yes (IMM)

22 Video Graphics Card

NVIDIA Quadro 600,CUDA Cores: 96,Total Frame Buffer: 1 GB DDR3,Memory Interface: 128 bit,Memory Bandwidth: 25.6GB/s

Display Port: 1,Maximum Display resolution: 2560 x 1600 Shader Model: 5.0,OpenGL: 4.0,Microsoft Direct X: 11 NVIDIA CUDA Architecture: Yes, Mosaic Technology: Yes Display Management Software: Yes, FSAA (Max): 64 x

23 Optional systems management adapter Virtual Media Key (optional)

24 Predictive Failure Analysis (PFA) support Memory, HDDs, and the onboard battery

25 No of Power Supplies 1 +1 ( redundant) 26 No of cooling fans 4 (As per the server design)

27 Operating System Windows Server 2007 / Windows Server 2008, should be compatible with the supplied video management software and analytics.

28 Anti Virus Norton (Latest) or approved equivalent with free upgrades till validity of contract including comprehensive AMC period

29 Approved makes IBM, HP, Dell

V Workstation: Workstation consists of a CPU and a Monitor, (A,B or C as per BOQ) A Specifications for Workstation CPU FEATURES MINIMUM REQUIRED PARAMETERS 1 Processor Intel Xeon W3550 Dual Core 2 Cache 4 MB 3 Storage Connector 5 X SATA Connector 4 Drive DVD

5 Memory DDR (2 GB) 6 Audio Support Yes

7 Video Graphics Card

NVIDIA Quadro 600 CUDA Cores: 96 Total Frame Buffer: 1 GB DDR3 Memory Interface: 128 bit Memory Bandwidth: 25.6GB/s Display Port: 1 Maximum Display resolution: 2560 x 1600 Shader Model: 5.0 OpenGL: 4.0 Microsoft Direct X: 11 NVIDIA CUDA Architecture: Yes Mosaic Technology: Yes Display Management Software: Yes FSAA (Max): 64 x

8 Ethernet 10/100/1000 Slot 9 HDD Bays 5 (Internal)

10 External Ports USB (8 ports) 11 Peripherals Multimedia Keyboard, Mouse & VGA Monitor slots 12 Storage 1 TB

13 Display (Monitor as per specifications given in item no 7.2 a and 7.2 b)

- 32” at Location In-Charge’s Cabin - 22” at Control Room and Security Cabin (Pl. refer detail Specifications provided separately in item no 7.2 a and 7.2 b)

14 Operating System Windows 2007 / Windows 2008 (Compatible with Client software)

15 Anti Virus Norton (Latest) or approved equivalent with free upgrades till validity of contract including comprehensive AMC period

16 Approved makes HP, Dell, IBM B Monitor-32” Flat Screen for workstation: (To be provided at Location In-Charge’s Cabin) Feature Parameter 1 Type LED 2 Resolution High Defination resolution of 1920 x 1080 pixels 3 Internal Speakers 2 4 Front Controls Power On/Off with LED

5 Scan System Automatic NTCS/PAL; 31.5 – 80 Hz (Horizontal); 56-75 Hz (Vertical)

6 Video connectors BNC (Composite Video)-2 Channels (looping);4-Pin Mini DIN(Y/C Video) DVI-I,15 pin D-Sub for VGA/SXGA Audio Inputs PC Audio (mini jack) Video Audio (2 Channel RCA –looping)

7 Input Composite Video / AV/VGA/HDMI/COMPONENT 8 Power Input AC Input- 100 to 240 V – 0.5 A,50/60 Hz 9 Power Output DC Output – 12VDC,0.5 A

10 Power Cord Detachable IEC 11 Display Mode DVI-I/SXGA/XGA/VGA 12 Display Colors 16.7 Millions 13 Luminance 400 cd/m2 14 Contrast Ratio 50000:1 (Dynamic), 1000:1 (Typical) 15 Viewing Angle 1400 Horizontal, 1600 Vertical 16 Operating Temperature 5OC to 40OC 17 Storage Temperature -25OC to 60OC 18 Operating Humidity 30% to 80% relative, non-condensing 19 Emmissions FCC: Part 15, Class B 20 Immunity CE: EN55022: 1998/A1:2000/A2:2003 21 Safety UL/Cul:6500,EN60950-1:2001 22 Make Samsung, Sony, Sharp, Toshiba, Philips, LG

C Monitor-22” Flat Screen for Workstation: (To be provided at Control Room and Security Cabin)

Feature Parameter 1 Type LED 2 Resolution High Definition resolution of 1280 x 1024 pixels 3 Internal Speakers 2 4 Front Controls Power On/Off with LED

5 Scan System Automatic NTCS/PAL; 31.5 – 80 Hz (Horizontal); 56-75 Hz (Vertical)

6 Video connectors BNC (Composite Video)-2 Channels (looping);4-Pin Mini DIN(Y/C Video) DVI-I,15 pin D-Sub for VGA/SXGA Audio Inputs PC Audio (mini jack) Video Audio (2 Channel RCA –looping)

7 Input Composite Video / AV/VGA/HDMI/COMPONENT 8 Power Input AC Input- 100 to 240 V – 0.5 A,50/60 Hz 9 Power Output DC Output – 12VDC,0.5 A

10 Power Cord Detachable IEC 11 Display Mode DVI-I/SXGA/XGA/VGA 12 Display Colors 16.7 Millions 13 Luminance 400 cd/m2 14 Contrast Ratio 500:01:00 15 Viewing Angle 1400 Horizontal, 1350 Vertical 16 Operating Temperature 5OC to 40OC 17 Storage Temperature -25OC to 60OC 18 Operating Humidity 30% to 80% relative, non-condensing

19 Emmissions FCC: Part 15, Class B 20 Immunity CE: EN55022: 1998/A1:2000/A2:2003 21 Safety UL/Cul:6500,EN60950-1:2001

22 Make Samsung, Sony, Sharp, Toshiba, Philips, LG

VI Industrial Grade Layer 2 managed Network Switch for outdoor applications

Features Minimum Requirements

1 Switch configuration

Layer 2 managed switch with eight Ports 10/100 Mbps N-way fast Ethernet switch with two no. 1000 Mbps fiber optic ports for distances up to 10km & above. Self-test/alarm output for reporting errors Dual redundant power inputs with MIL- STD-1275 surge and spike protection DIN rail or direct panel mounting (no extra kits required). shall be compatible for access control signals, if required

2 Ether net performance

A Operation Store and forward wire speed switching, non-blocking.

B Modes Full or half duplex operation with flow control supported on all ports

C MAC Addresses 8000 D Switching capacity >5 Gbps

Capacity in Millions of packets per second (mpps)(64-byte packets

>4 mpps

E Latency (typical) 5 micro sec for 1000 Mbps and 16 micro sec for 10 Mbps (plus frame time)

F Ethernet Isolation 1500 Vrms 1 minute

3 RJ45 Copper Ports

A RJ45 Ports Min. 8 Nos of RJ45 ports that are fully IEEE 802.3 compliant

B POE Support Min 2 Ports (max support class 3, 15.4W per port)

C RJ45 Speed & duplex Auto-detecting for speed(10/100)& duplex ( full or half)

D RJ45 MDI/MDIX Auto-mdi/mdix-crossover automatically. supports either straight or crossed cables

E RJ45 Polarity Auto-polarity for automatic correction of crossed TXD and RXD pairs

4 Fibre Optic Ports

A Fibre Optic ports Min. 2 no. of 1000 Mbps fibre optic ports for distances up to 10 km

B Port speed 1000BaseFX (1000 Mbps)

C Fibre duplex operation full duplex

D Transceivers SC or ST style

E Single Mode Links up to 10 km typical; 1310 nm; with 9-10/125 um fibre

F Safety IEC60825-1, Class 1; FDA 21 CFR 1040.10 and 1040.11

5 Networking Features

A Spanning tree protocol (STP) Standard 802.1d spanning tree support. Fast convergence using 802.1w(Rapid spanning Tree (RSTP), enabled by default Multiple spanning tree instances using 802.1s(MSTP)

B Port Grouping

Support for IEEE 802.3ad Link Aggregation Control Protocol ( LACP) Up to 8 groups Up to 8 ports per group with 16 candidate ports for each

(dynamic)803.3ad link aggregation

C VLAN

Support for up to 256 VLANs simultaneously, Port based and 802.1Q tag – based VLANs, MAC-based VLAN, Management VLAN, Private VLAN Edge (PVE), with multiple uplinks, Guest VLAN & Unauthenticated VLAN

D Voice VLAN Voice traffic to be automatically assigned to a voice specific VLAN and treated with appropriate levels of QoS

E Devices supported by all All IEEE 802.3 compliant devices are supported

F Protocols & features All IEEE 803.2, QoS/CoS/ToS/DS, port mirroring,broadcast storm protection, Modbus monitoring

G Industrial Protocols Supported

Modbus/TCP, Ethernet/IP, PROFInet, Foundation Field bus HSE and others

H

Ethernet Communications Standard IEEE 802.3 IEEE 802.3u IEEE 802.3ab IEEE 802.3z IEEE 802.3ad IEEE 802.3x IEEE 802.3ad IEEE 802.af IEEE 802.1d IEEE 802.1p IEEE 802.1Q

10Base-T Ethernet 100Base-TX/FX 1000Base-T Gigabit Fiber LACP Flow Control and Back Pressure Port trunk with LACP Power over Ethernet (Mode A) Spanning Tree/IEEE 802.1W Rapid Spanning Tree Class of Service VLAN Tag

IEEE 802.1x IEEE 802.1ab Port Connector

User Authentication (Radius) LLDP 10/100TX:RJ-45 x 8 SFP Combo: RJ-45 x 2, 100/1000 SFP x 2 Console port : RJ45 x 1

I

Performance

Wire-Speed forwarding rate 14,880pps for 10Mbps Ethernet 148,800pps for 100Mbps Ethernet 1,488,000pps for 1000Mbps Ethernet Mac Address : 8K Packet Buffer : 1Mbits Wire-Speed forwarding rate 14,880pps for 10Mbps Ethernet 148,800pps for 100Mbps Ethernet 1,488,000pps for 1000Mbps Ethernet DRAM 32Mbytes Flash ROM : 4Mbytes Switching Fabric : 5.6Gbps Throug hput 8.3Mbps@64bytes (Full Duplex)

J

Management Configuration VLAN Redundancy Security Traffic control Diagnostics

SNMP v1/v2c/v3, Web, Telnet, CLI IEEE 802.1Q, GVRP, Port-based VLAN Up to 4096 VLAN ID X-Ring, Dual Homing and Couple Ring, IEEE 802.1d STP and IEEE 802.1w RSTP IP Access security, port security, DHCP Server, IP Binding per Port, IEEE 802.1x Port Access Control IGMP Snooping/ Query for multicast Port trunking, Static IEEE 802.1p QoS/ CoS/ToS/DSCP priority queuing, IEEE 802.3 x flow control Port Mirroring, LLDP,Real time traffic statistic, MAC Address Table, SNTP, Syslog, E-mail Alert, SNMP Trap, RMON

K Mechanism

Enclosure IP30, Metal with aluminum shell

Installation DIN-rail/Wall Mount Design

L TFTP Firmware update, system configure restore and back-up

M SNMP v1/v2c/v3, Web, Telnet, CLI Management

N

• Provides standards-based IEEE 802.3af • Power over Ethernet upto 8 ports of class 3 powered devices at 15.4 watts • Ingress Packet Filter and Egress Rate Limit

N

LED Indicators

System: Power, Power 1, Power 2, Fault, Master 10/100TX : Link/Activity, FDX/COL Giga Copper: Link/Activity, Speed SFP: Link/Activity

6 Power and Alarm Output

a Power Input Dual redundant power inputs for redundant power supplies

b Input Voltage Range 10 to 50 VDC

c Power Typical with all ports linked and active

d Industrial surge & spike protection 15 kW peak, 5 kW (10 times for 10 us)

E MIL-STD-1275 surge and spike protection (All models)

Surge: 100V for 1 second ... Transient: 15,000 watts peak Spike: 250 volts (50 times for 100 uS)

F Self-test / Alarm Same voltage as power input; 0.5 Amps

g Output max. 7 Environmental a Operating temp. 0 to 60°C

b Storage Temperature 0 to 50°C

c Humidity 5 to 95% RH (non-condensing) d Vibration IEC6008-2-6 e Shock IEC6008-2-27 f Freefall IEC6008-2-32 8 Standards and Certifications

a Standard safety Relevant UL standard viz.UL60950 etc. or as applicable, Relevant EN standards viz. EN60950-1 etc or as applicable.,CE Marking

B Mechanical stability Shock—20g (operational), 30g (nonoperational)

C EMC interface immunity IEC 61000.Relevant IEC standards, viz. IEC 60950(CB) etc. or as applicable

d EMC (Standard & industrial) FCC part 15, ICES-003, EN55022, IEC60533

E Hazardous Locations UL1602, CSA22.2/213 (Class I, Div. 2, Groups A, B, C, D); Cenelec EN50021 (Zone 2), IEC 60079-15

g Traffic NEMA TS-2 rated for traffic control systems

H Marine and Off-shore DNV (Det Norske Veritas) No. 2.4.

I MTBF Mean Time Between Failure: >1,00,000 hours. J RoHS and WEEE RoHS (Pb free) and WEEE compliant.

k Certifications CE, FCC Class A & UL (UL/cUL60950-1), EN61000-6-4, EN61000-6-2, EN61000-4-2 (ESD), EN61000-4-3 (Radiated RFI), EN61000-4-4 (Burst), EN61000-4-5 (Surge), EN61000-4-6 (Induced RFI), EN61000-4-8 (Magnetic Field), IEC60068-2-27, IEC60068-2-32 & IEC60068-2-6.

9 Mechanical a Case Low Profile, Ideal for shallow enclosures and tight spaces

b Material Rust-proof Lexan and aluminum with clear protective coating

c Protection IP 30

d Mounting DIN rail or direct to panel (no optional kits or accessories required)

e Enclosure The layer 2 switch shall be enclosed in a IP 65 enclosure with cooling fan.

f Accessories/ connectors Cost of level-2 switch shall include cost of connecting OFC & CAT-6 cables from the cameras to the switch

g Make Cisco, Ruggedcom, Garretcom, Allied Telesis 10 Quality of service a Priority levels 4 hardware queues

b Scheduling Strict priority and weighted round robin (WRR)

c Class of service Port based ; 802.1P VLAN priority based ; IPv4 precedence/type of service(ToS)/DSCP based ; Differentiated services; classification and re-marking ACLs, trusted QoS.

d Rate limiting Ingress policer; egress shaping and rate control; per VLAN, per port & flow based

VII

Layer 3 managed Switch for indoor applications ( Layer-2 switch shall also be acceptable with configuration of ports as given below & specifications of layer-2 switch as given above). Purpose of this switch is to integrate the layer-2 switches provided in the field with NVR server/ VMS & for uploading the videos through internet.

FEATURES MINIMUM REQUIRED PARAMETERS 1 Ethernet Ports 24 X 10/100/1000 Base-T

2 Fiber ports 4 X 1000Base-XSFP Combo ( Single mode) To be expandable to accommodate additional 4 no.OFC connections for locations ( 64 cameras)

3 System Capacity

32MB SDRAM 16MB flash memory 200MHz PowerPC CPU 4096 VLANs 16000 MAC addresses 8 Megabytes file system Packet buffer memory 1Mbit

4 Performance

Wire speed switching on all Ethernet ports 14,880pps for 10Mbps Ethernet 148,800pps for 100Mbps Ethernet 1,488,000pps for 1000Mbps Ethernet Ethernet throughput 71.424Mpps Switch fabric 96Gbps

5 Interface Standards

IEEE 802.3 10T IEEE 802.3u 100TX IEEE 802.3z 1000SX IEEE 802.3ab 1000T

6 General Standards IEEE 802.1d Bridging IEEE 802.3ac VLAN tag frame extension IEEE 802.3x Back Pressure / flow control

7 Redundancy

Static and dynamic port trunking (with six trunk groups and up to 8 ports per trunk) IEEE 802.3ad 32 LACP link aggregation1 IEEE 802.1D Spanning-Tree Protocol IEEE 802.1w Rapid Spanning-Tree IEEE 802.1s Multiple Spanning-Tree BPDU guard1 Loop guard1 Router Redundancy Protocol (RRP) snooping Dual software images, dual configuration files

8 Traffic Management Quality of Service (QoS)

Layer 2, 3 and 4 criteria Flow groups, traffic classes and policies DSCP replacement IEEE 802.1Q priority replacement Type of Service replacement Type of Service to IEEE 802.1Q priority replacement IEEE 802.1q Priority to Type of Service replacement

Maximum bandwidth control Burst size control Ingress rate limiting Head of line blocking prevention Support for ingress and egress ports Eight egress queues per port IEEE 802.1p Class of Service with Strict and Weighted Round Robin Scheduling

9 Multicast

RFC 1112 IGMP snooping (v1) RFC 2236 IGMP snooping (v2) RFC 2710 Multicast Listener Discovery (MLD) snooping (v1) RFC 3810 Multicast Listener Discovery (MLD) snooping (v2) IGMP snooping querier1

10 Management & Monitoring

RFC 1157 SNMPv1 RFC 1901 SNMPv2 RFC 3411 SNMPv3 RFC 1213 MIB-II RFC 1215 TRAP MIB RFC 1493 Bridge MIB RFC 2863 Interfaces group MIB RFC 1643 Ethernet-like MIB RFC 1757 RMON 4 groups: Stats, History, Alarms and Events RFC 2674 IEEE 802.1Q MIB RFC 1866 HTML RFC 2068 HTTP RFC 2616 HTTPS RFC 854 Telnet server RFC 1350 TFTP client IP address allocation: RFC 951 / RFC1542 BOOTP client RFC 2131 DHCP client manual RFC 2030 SNTP, Simple Network Time Protocol BootP/DHCP relay Group link control1 Link flap protection1 Syslog client Two event logs:

4,000 event capacity in temporary memory 2,000 event capacity in permanent memory

11 Management Access Method

Single IP address for management Out of Band management (serial port)

In-band management (over the network) using Telnet, Web browser or SNMP Enhanced Stacking

12 Management Interfaces

Menus Allied Ware PlusTM CLI Multiple management sessions (up to three administrators) Command line Web browser SNMP v1/ v2/ v3

13 Security

RFC 1492 TACACS+ RFC 2865 RADIUS client RFC 2866 RADIUS accounting IEEE 802.1x Port-based network access control with multiple supplicants per port ingress and egress control of broadcast, multicast and unknown unicast traffic MAC address security/lockdown Layer 2/3/4/ Access Control Lists (ACLs) 64 ACL profiles 256 rules per ACL profile ACLs based on: • Ethernet frame type • MAC address/VLAN ID/IEEE 802.1p • Layer 2/3 protocol • IP subnet/address/TOS/DSCP • UDP/TCP port/flag SSHv2 for Telnet mgmt SSLv3 for Web mgmt DoS attack protection Smurf SYN flood Teardrop Land IP option

Ping of Death SNMP attack Microsoft NAP compliant Symantec NAC support

14 Fault Protection Bad cable detection Broadcast storm control

15 MTBF > 200000 hours 16 Operating Voltage 120V to 220 V AC 17 Operating Temperature 0° to +40° C 18 Certifications UL 19 Approved Makes Cisco, HP, Juniper, Allied Telesis, Nortel

VIII Media Converter

FEATURES MINIMUM REQUIRED PARAMETERS 1 Type Ethernet Data to Fiber & Vice-Versa 2 Ports 2 (Two). One Ethernet Port & One Fiber Port 3 Multiplexing Integrated Wavelength Division Multiplexing 4 Auto negotiation Yes (Between 10Mbps & 100 Mbps Data rates) 5 Range Selection 10 Mbps & 100 Mbps 6 Communication selection Full & Half Duplex 7 Link Down Detection Yes

8 Multimode & Single Mode Support Yes

9 Transmission Device Laser Diode 10 Outdoor Application Yes 11 Switching Method Store & Forward 12 Compliance IEEE 802.3, 802.u, 802.3x 13 Interface Auto MDI / MDI-X 14 LED Indicators Yes

15 Shock & Vibration Resistant Yes

16 Enclosure

- Media converter used for outdoor application at Camera and layer 2 switch end shall be housed in IP65 enclosure at the bottom of the pole.

- Media converter used for indoor application at layer 3 switch end shall be housed in proper enclosure.

17 Certifications CE, FCC & UL 18 Operating Temperature 0° to 70°C 19 Operating Voltage 12V DC / 24V AC

20 Approved Makes Reputed Make as approved by BPCL provided bidder shall submit Proven Track Record from the user at least one year from tender due date along with the bid.

IX Uninterrupted Power Supply FEATURES MINIMUM REQUIRED PARAMETERS 1 Topology Online (Double Conversion) 2 Input Power Factor >0.95 3 Nominal Input Voltage 220V/230V/240V (Single Phase) 4 Input Frequency 50/60 Hz (Accuracy of +-5 Hz) Auto Sensing 5 Input Connections 3 Wire 6 Input Voltage Range (Full Load) 160 – 280 V (Single Phase) 7 Input Voltage Range (Half Load) 100 – 280 V (Single Phase) 8 Output Power Capacity 3 KVA / 2100 Watts 9 Output Power Factor 0.7

10 Nominal Output Voltage 230V configurable for 220V, 230V and 240V 11 Efficiency (Full Load) 88% 12 Output Voltage Distortion > than 3% 13 Output Frequency (Sync to mains) 50/60 Hz (+/- 3 Hz) 14 Crest Factor 3:01 15 Waveform Pure Sine Wave 16 Output Connection 3 Wire

17 Backup Battery type Sealed Maintenance free Lead – Acid Battery with suspended Electrolyte

18 Bypass Built-in 19 Interface Port DB-9, RS-232,Smart Slot 20 Web SNMP Card Interface One

21 Compatible Web SNMP Card for Network Management & Environmental Monitoring

Browser Accessible, Customizable input contacts, Customizable output relays, Data Logging, Event Logging, Fault Notification, Flash Upgradeable, O.S shutdown, Password Security, Radius support, Read only access, Reboot equipment remotely, Run Command File, Server shutdown, Telenet Management, Temperature Monitoring

22 Control Panel LED status displays with Load & battery Bar graphs 23 Audible Alarms Battery ON, Battery LOW & Overloading 24 Emergency Power Off (EPO) Optional

25 Filtering Full Time multiple pole filtering, 0.3% IEEE surge let through and Zero clamping response time

26 Surge Energy Rating 420 Joules

27 Audible noise at 1 meter from unit surface < 55 Dba

28 Online Thermal Dissipation < 652 BTU/hr

29 Operating -Temperature, Humidity 0° to 40° C , 0-90%

30 Approved Makes APC, Emerson, Numeric, Su-kam, Microteck

X Mounting Pole: Feature 1 Type Self Support 2 Material Galvanized Steel 3 Height 3 or 6 mtrs as per site requirements 4 Wind Speed 180 Kmph 5 Stress Within acceptable limit

6 Foundation

The foundation of pole to be designed for three types of soil namely soft, medium, hard/rocky.

1. The foundations design to be as per the actual site conditions.

2. Guard against corrosion and soil erosion should be taken care of.

3. The back filling should be done by proper compaction of soil in layers and should be done before erection M20 concrete shall be used .Material mixing and quality control of concrete shall be as per IS 456:2000. High strength deformed steel bars of grade Fe 415 confirming to IS:456 shall be used. Bending of bars shall be as per IS 2502 (1963)

4. Welding shall be done as per IS:9595 (1996)

7 Painting

The paints used shall be in accordance with IS 2074/62, 2932 & 2933/75.Before applying coat of primer, the surface shall be given a coat of pickling agent so as to avoid flaking of painting. The pole shall be given two coats of paint in addition to primer coat after erection. The pole shall be painted as per the international standard and civil aviation guidelines.

8 Earthing

50x3 mm GI strip should be bonded to the base of the pole and connected to earth pit / grid (if available in the plant or If a new earth is to be provided same shall be provided by BPCL) at the other end (max value of the earth resistance shall be 0.5 ohms).

XI Armoured CAT-6 Cable FEATURES MINIMUM REQUIRED PARAMETERS

1 General Features

High ACR Values Low Bit Error Rates Electromagnetic Compatibility Minimum Radiations effect Maximum Noise Immunity 4 Twisted Pairs

Compliant with standards ISO/IEC 11801 2nd Ed., EN 50173-1: May 2007 (DIN EN 50173-1), DIN 44332-5, IEC 61156-5 2nd Ed., EN 50288 x-1, 10Gbase T in acc. With IEEE 802.3an: June 2006, tested and certified by independent laboratory.

Low-smoke in acc. With IEC 61034, flame-retardant in acc. With IEC 60332-1 and halogen-free in acc. With IEC 60754-2.

2 Outer Diameter 7.5 mm or lesser (Nominal) 3 Conductor Diameter 0.573 mm (AWG) 4 Conductor Type 23 AWG bare annealed Copper 5 Jacket Material PVC 6 Color Blue / Red / Grey 7 Overall Shield Tined Copper Braiding 8 Electrical Impedance 100 +- 6 Ohms@ 1300 MHz 9 DC Resistance 74 Ohms/km (Max)

10 Voltage Rating 70 V DC 11 Dielectric Strength 1500V/minute 12 Insulation Resistance 500 M Ohms / Km (min) @ 500VDC 13 Velocity of Propagation 69% 14 Certifications UL

15 Approved Makes 3 Com, ADC Krone, Molex, R&M, Digilink, Avaya, Panduit, Clipsal,Beldon

XII Power Cable FEATURES MINIMUM REQUIRED PARAMETERS 1 Cable Type Copper 2 Voltage Rating Up to 1000V 3 Size 3 Core 2.5 Sqmm

4 Construction

Annealed Bare Electrolytic Grade Copper Conductor as per IS: 8130/84 Solid Conductor up to 2.5 square mm Multi stranded conductor for 2.5 sq mm & above

5 Primary Insulation Extruded PVC Compound as per IS: 5831 Type A 0.9 mm nominal thickness

6 Inner Sheath Extruded PVC Compound Type ST1, Minimum thickness as per Table 4 of IS: 1554 Part-1

7 Outer Sheath Extruded PVC Compound Type ST1, Minimum thickness as per Table 7 of IS: 1554 Part-1

8 Armor Galvanized Steel Wire armored dimensions as per table-5 of IS:1554 Part-1

9 Application Outdoor (Direct Burial in trenches)

10 Core Identification Red, Yellow & Blue

11 Approved Makes Polycab, Finolex, Associated cables, Fort, CCI, Universal cables, Delton, Belden

XIII Power Cable

FEATURES MINIMUM REQUIRED PARAMETERS 1 Cable Type Copper 2 Voltage Rating Up to 1000V 3 Size 3 Core 1.5 Sqmm

4 Construction

Annealed Bare Electrolytic Grade Copper Conductor as per IS: 8130/84 Solid Conductor up to 1.5 square mm Multi stranded conductor for 2.5 sq mm & above

5 Primary Insulation Extruded PVC Compound as per IS: 5831 Type A 0.9 mm nominal thickness

6 Inner Sheath Extruded PVC Compound Type ST1, Minimum thickness as per Table 4 of IS: 1554 Part-1

7 Outer Sheath Extruded PVC Compound Type ST1, Minimum thickness as per Table 7 of IS: 1554 Part-1

8 Armor Galvanized Steel Wire armored dimensions as per table-5 of IS:1554 Part-1

9 Application Outdoor (Direct Burial in trenches) 10 Core Identification Red, Yellow & Blue

11 Approved Makes Polycab, Finolex, Associated cables, Fort, CCI, Universal cables, Delton, Belden

XIV Fiber Optic Cable

FEATURES MINIMUM REQUIRED PARAMETERS 1 Cable Type Armored Loose Tube Jelly Filled (Multi-Tube), rodent resistant. 2 Fiber Type Single Mode, 9 / 125, 250 micron primary coated buffers

3 Fiber Core As per Telecordia GR20, ITU-T G652D, IEC- 60793-2-50, TIA/EIA 492-CAAB

4 No of Cores 12 5 Armoring Corrugated Steel Tape Armor

6 Cable Construction Type BELLCORE GR 20 / IEC 794-1 - Loose tube Corrugated steel tape (0.155mm Min)CSTA provided with FRP Rod as strength members

7 Outer Jacket Construction High density polyethylene, anti - termite, anti - rodent suitable for direct burial application

8 @1310nm < = 0.35 dB/Km 9 @1500nm < = 0.20 dB/Km

10 Maximum Tensile Load >= 2670 N

11 Maximum Crush Strength >= 2670 N 12 Operating Temperature -20° to +70° C 13 Certifications UL

14 Approved Makes ADC Krone, Molex, R&M, Avaya, Panduit, clipsal, Olex, Digilink

XIV Optical Fiber Cable Accessories FEATURES MINIMUM REQUIRED PARAMETERS

1 LIU

LIU should be provided for terminating the optic fiber cables. It shall provide minimum bending radius and the splice trays shall function as a splice cover for pigtail splicing. It shall be made of aluminium with power coating in compliance with latest industry standards. Cable glands shall be provided at the cable entry point for tight sealing. The splice tray shall be made of ABS materials.24 Port. It shall be fitted with SC couplers and all accessories for termination. Make-Allied Telesys, Nortal, Cisco, D-Link.

2 Pigtails SC Type; 1 M; Insertion Loss< 0.5 db; Return Loss>40 db; Bend Radius>30 mm

3 Optical Fiber Connectors Optical Fiber connectors should be single mode SC/ST Type with push pull mechanism and fully in compliance with latest industry standard. Optic fiber connectors should be of standard make.

4 Optic Fiber Adapters

Optical Fiber adaptors should be suitable for single mode SC/ST Type fiber cable connectors and shall be fully in compliance with latest industry standard. It shall be with snap/latch mechanism. Optic fiber adapters should be of standard make

5 Optic Fiber Patch Cords

Optical Fiber patch cords should be suitable for single mode SC/ST Type fiber cable connectors and plastic moulded plug type connectors and shall be fully in compliance with latest industry standard. It shall be of should be of standard make.Min Return Loss >50 db

6 Rack 6U 19” Network Rack with cable Managers and 1 fan.

XV CABLE LAYING

1 CABLE LAYING SPECIFICATIONs:

The cable has to be laid along the walls or underground through HDPE pipe as per the site conditions at minimum 600 mm depth. Job excludes excavation , back filling & restoration in any kind of soil & backfilling . Job includes laying of cable, HDPE pipe, supervision of backfilling etc. to complete the job

The bidder shall quote for Supply & laying of all the cables [(Power-3C-2.5Sqmm (between Layer3 switch to Layer-2 Switch), 3C-1.5Sqmm (Between Layer 2 switch to MC, PTZ Camera),(Signal cable- Armoured Cat-6 and OFC)] on RM basis, excavation for cable laying shall be in BPCL scope: OFC supplying & laying rates shall include cost of BIS mark HDPE pipe of 50 MM diameter CAT-6 cable supplying & laying rates shall include cost of BIS mark , heavy duty, PVC pipe of 40 MM diameter . Power cables shall be laid separately in open trench along the HDPE pipes ( duly clamped) where ever laid above ground Laying of cable in HDPE pipe trenches/ in ISI mark PVC conduits on walls/GI pipes to be used for Road crossings. ( G.I. pipes, if required for raod crossings shall be provided by BPCL) Pulling of cable through HDPE pipe and GI Pipe and sealing ends including unused sleevs, including cleaning of pipes. All entries shall be sealed with sealing compound. Supplying and providing of MS Clamp of required sizes to hold the cable firmly to structure/tray. Such clamps also include wooden bushes if required to be placed around cable, sealing compound, etc. All entries shall be sealed with sealing compound.

Underground cable laying shall include termination at both ends, supply of HDPE pipe for underground cables, supply of ISI Mark PVC pipe for cables along the walls, supply of GI pipe for road crossings etc. Cable route markers @ 30 meter interval to be provided Bending radius of cables shall not be less than 12 times O.D. of cable All cores of cable shall be identified at both ends by means of PVC ferrule Cable leads shall be terminated at both ends by crimped type soldering

Necessary loops of 2-3 m to be provided at a distance in the multiples of 50 m. As far as possible there shall be no joints in the cables

All junction boxes, local cabinets, field mounted instruments shall be connected to the nearby existing earth bus bar / earth pit through minimum 1.5 mm2 copper conductor at no extra cost to Corporation. It is included in the scope of the individual items. Wherever required FLP junction boxes to be used at no extra cost to Corporation

All equipments and fittings used should be of ISI marked confirming to relevant IS codes The shield of the shielded cable shall be earthed with earth at one end only i.e., at control room end

Note :

1. All the accessories required for the successful commissioning of the system viz junction boxes, connectors, etc are to be included in costing of the associated item while quoting.

FACTORY INSPECTION: TPIA shall be arranged by vendor to witness performance tests on two randomly selected equipments. TPIA shall also review all the performance test certificates as per QAP

FAT: Integrated FAT shall be conducted at vendor/integrator’s works for demonstrating all the performance parameters using randomly selected equipments

SAT : Integrated SAT shall be conducted at BPCL site works for demonstrating all the performance parameters using randomly selected equipments

Annexure a.

1. IP Network Cameras:

Minimum Specifications 1 BRIEF:

The box type camera shall provide higher resolution (full HD), realtime video images, encapsulated in Internet Protocol (IP) packets and presented through a 10/100 BASE-T RJ45 Ethernet network connections.

2 RESOLUTION & IMAGER:

Latest Imager 1/3 Progressive Scan, CCD Or High Density CMOS

MegaPixels -1920 X 1080 resolution (1080P full HD)– Minimum Standard

The image resolution shall be not be less than 1920(H) x 1080(V) pixels at 30 frames/sec (NTSC 30 & PAL 25 PAL) .

3 FRAME RATE: The camera shall produce a frame rate of 30 frames(NTSC 30 & PAL 25 PAL) per second (fps) at minimum resolution of 1920(H) x 1080(V) , (1080p Full HD) with H.264 compression ratio.

4 STREAMING : Camera should support multiple steaming with minimum requirement of three (3) H.264 independent streams at default resolution of 1920 X 1080 (1080P full HD). For resolution, multiple options of resolution like 720P, VGA,QVGA, etc should be available for selection for any particular stream.

5 DAY & NIGHT CAMERA : The camera shall have IR cut filter which shall switch from color to monochrome automatically by sensing the illumination level. The camera should be capable of capturing both color and B &W (Black & White) video with minimum Color Illumination of 0.7 lux for Color and upto 0.08 Lux for B & W, for deliverance of video captured in very low luminous environment/conditions.-

6 ASPECT RATIO: Aspect ratio should be 16:9.

7 BACK LIGHT COMPENSATION :The camera shall have smart BLC to compensate the image without compromising the dynamic range.

8 WIDE DYNAMIC RANGE: For harsh lighting, the camera should have Wide Dynamic Range functionality to resolve details in the scene s brightest areas to get a clear picture.

9 AUTO IRIS : Camera should have Auto Iris to work seamlessly in all varying light conditions.

10 ONVIF (Open Network video Interface Forum)Camera model proposed for the tender should be conforming to ONVIF standards to ensure integration with third party management systems & video network devices.

11 NETWORK CONNECTIVITY:

10/100 Base-T, auto-sensing, half/full duplex,RJ45,

PoE IEEE 802.3af compliant.

Access to be password protected.

Should support IP filtering

Should provide integrated support to IPv4, IPv6, TCP, DHCP, HTTP, UPnP, DDNS, IGMP, HTTPS, SMTP, FTP and 802.1X.

12 CAMERA PROCESSOR:

The camera processor shall have at least 256MB of RAM and 128MB of flash memory.

Should efficiently handle minimum three (3) independent H.264 streams.

13

FAIL SAFE:

If the controlling Server equipped with the remote monitoring software fails, then the camera Encoder s built in web server should enable any PC on the network to monitor camera for mission critical application. No unique or proprietary client software shall be required for viewing or controlling the camera.

14 ALARMS:

Alarm Input/ Output 2/1. Event based alarm generation (http based) :

Tamperproof alarm which includes spray on camera, out of focus, blocking, camera shift, etc

15 CAMERA LENS:

Megapixel Varifocal lens- minimum 3 MM to 8 MM.

Camera should support hassle free replacement of existing lens with higher configuration varifocal lens in future.

16 Housing Outdoor to be confirming to (IP 66). Camera can also be with IP66 casing with standard mounting bracket.

17 CERTIFICATIONS:

EN or UL and FCC

18 OPERATING TEMPERATURE: -0°C to +50°C

19 HUMIDITY: 80% RH

20 IMAGE SETTING:

Adjustable image size, quality and bit rate .

Should support digital zooming.

Should support both Constant bit rate and Variable bit rate configuration for bandwidth optimization.

Time Stamp & text caption overlay

Configurable brightness, contrast, saturation, sharpness and white balance

AGC,AWB,AES

Automatic, manual or scheduled day/night mode

Support Privacy masks

21 LICENSE FEES:

There should not be any license fees for accessing camera including the firmware up gradation.

22 NTP:

Shall have Embedded real-time clock and shall have built in support for Network

Time Protocol (NTP)

2. CAMERA HOUSING:

1 Housing should be Aluminum di-cast. Powder coated, Mounting bracket with provision to accommodate cat6 cable internally, without hanging out.

2 The Camera Housing should be conforming to IP 66 rating. The supporting certificate to be attached.