workshop - bpw transpec … · workshop. 2014 2 member of vbg group frequently asked questions ....

Post on 11-Aug-2020

3 Views

Category:

Documents

0 Downloads

Preview:

Click to see full reader

TRANSCRIPT

1 2014 Member of VBG GROUP

Workshop

2 2014 Member of VBG GROUP

Frequently asked questions

3 2014 Member of VBG GROUP

?????????????

Why does the coupling not close down when the

drawbar eye is being introduced?

The coupling is:

- Open

- Safety is in open position

- The coupling bolt is in upper end position.

Frequently asked questions

???

4 2014 Member of VBG GROUP

The wearing plate and/or the drawbar eye are worned out

excessively.

Frequently asked questions

worn out new

5 2014 Member of VBG GROUP

Frequently asked questions

???

6 2014 Member of VBG GROUP

What could be the reason for this?

The driver opens the coupling:

- The coupling bolt doesn‘t remain in the opened stand

but drops down powerlessly.

Frequently asked questions

???

7 2014 Member of VBG GROUP

Frequently asked questions

1st Answer

By coupling the trailer drawbar eye has hit the front of

the top cover cap of the coupling. Caused by this hit the

2 locking springs insite the mechanism has moved from

position.

8 2014 Member of VBG GROUP

Frequently asked questions

2nd Answer

By excessive utilisation the springs are compressed

and lost power.

9 2014 Member of VBG GROUP

Frequently asked questions

Solution action for 1st option

Tap softly and alternately with a hammer on the

spots marked with A and B.

• Springs will straighten out again.

A

B

10 2014 Member of VBG GROUP

Solution action for 2nd option

Remove the springs to slightly extend them

repeatedly.

Frequently asked questions

11 2014 Member of VBG GROUP

???

Why?

During opening you can move the handle only

until half-open position of the coupling.

Frequently asked questions

12 2014 Member of VBG GROUP

Frequently asked questions

Slight inclination, out of center, of the coupling funnel because:

It possibly has not been moved for a long time (rust)

The return spring is damaged

The wearing pad is worn out

(Burr formation). Blocks into the inner wearing ring.

13 2014 Member of VBG GROUP

Frequently asked questions

The guiding funnel is not either in the position

90° to the truck nor in the right or left end

position.

14 2014 Member of VBG GROUP

Frequently asked questions

The guiding funnel can not move freely – the

retaining function is blocked!

15 2014 Member of VBG GROUP

Our recommendation:

Grease with Spray-Oil

(for example Mek Olja,WD40)

Frequently asked questions

16 2014 Member of VBG GROUP

Frequently asked questions

The wearing pad is worn out

(Burr formation)

18 2014 Member of VBG GROUP

Solution Change return spring if worn out!

Frequently asked questions

!!!

19 2014 Member of VBG GROUP

Why?

Excessive wear of the wearing plate

Frequently asked questions

???

20 2014 Member of VBG GROUP

Frequently asked questions

The wear plate was greased so that during

operation dirt particles have penetrated that stick to

the grease which now acts like an abrasive paper

23 2014 Member of VBG GROUP

Why?

The coupling bolt is jamming during the opening

process.

Frequently asked questions

???

24 2014 Member of VBG GROUP

Frequently asked questions

When driving with a trailer the coupling was not completely closed (e.g.

caused by dust and impurities on bottom guide bush) and thereby the

coupling bolt has got slightly bended in the shaft.

25 2014 Member of VBG GROUP

Frequently asked questions

Possible Reason:

Rust in the automatic unit! – No service greasing done!

26 2014 Member of VBG GROUP

Frequently asked questions

Possible Reason:

Wrong or too much greased!

27 2014 Member of VBG GROUP

Our recommendation:

Grease with Spray-Oil (for exampl Mek Olja,WD40)

Häufig gestellte Fragen · Frequently asked questions

28 2014 Member of VBG GROUP

Why?

Häufig gestellte Fragen · Frequently asked questions

Permanent broken parts out of funnel body

???

29 2014 Member of VBG GROUP

Frequently asked questions

You don‘t drive / use a RINGFEDER coupling.

RINGFEDER couplings cannot only be locked in three

different positions but also have an extremely strong

coupling body.

30 2014 Member of VBG GROUP

Thanks

top related