warning - cover-pools mechanism—underside™ track or track channel ... • tracks locked in place...
Post on 06-May-2018
220 Views
Preview:
TRANSCRIPT
This is a general guide on factors to consider for the installation of a Save-T 3 automatic cover system or Autosave spa cover.
Detailed installation instructions are available.
General Informationfor Installing an Automatic Pool Cover (Save-T® 3 or Autosave™ Spa Cover)
Cover-Pools Incorporated66 East 3335 SouthSalt Lake City, UT 84115
800.447.2838801.484.2724www.coverpools.com
©2015 Cover-Pools Incorporated800024 Rel-0024
Cover-Pools Incorporated is a wholly owned subsidiary of Zodiac Pool Systems, Inc. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.
All other trademarks used herein are the property of their respective owners.
®
WARNING 11pt
WARNING 12pt
WARNING 14 pt
WARNING 24pt
WARNING 21pt
WARNING 27pt
WARNING 37
10PT
FOR YOUR SAFETY—This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exists. In the event no such state or local requirement exists, the installer or maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or loss of life. Improper installation and/or operation will void the warranty.
All diagrams are for general information. Consult installation instructions for details.
3
Table of ContentsTRACK OPTIONS ...................................................................................................................... 4
EXCAVATION AND PLUMBING .................................................................................................. 6Recessed Mechanism—Underside™ Track or Track Channel ......................................... 6Recessed Mechanism—Universal, SnapTop™, or Flush Track ........................................ 7
ELECTRICAL ............................................................................................................................ 8Keyed Motor Control (Standard Equipment) .................................................................... 8Hydraulic Power System ................................................................................................... 8Auto-Shutoff with Amp Limiter and Accessory Board ..................................................... 9Auto-Shutoff with Amp Limiter/Accessory Board/Wireless ........................................... 9
MECHANISM HOUSING ........................................................................................................... 10Recessed Concrete, Wood, or UPB Box—Underside™ Track ........................................ 10Recessed Concrete, Wood, or UPB Box—Autosave OPTION 1: Conduit comes from back of box....................................................................11Recessed Concrete, Wood, or UPB Box—Autosave OPTION 2: Conduit comes from side of box. .................................................................. 12Recessed Concrete, Wood, or UPB Box—Universal or SnapTop™ Track ....................... 13Recessed Wood Box Construction .................................................................................. 13Deck-Mounted Bench Construction ............................................................................... 13
COPING AND DECK ................................................................................................................ 14Gunite Layout—Underside™ track .................................................................................. 14Coping or Deck Requirements—Underside track .......................................................... 14Coping or Deck Requirements—Underside track (cont.) ............................................... 15Tile Beam—Underside track .......................................................................................... 15
RECESSED BOX COVER .......................................................................................................... 16Brackets .......................................................................................................................... 16Vanishing Lid™ System .................................................................................................... 16Bezel™ lids ....................................................................................................................... 16
SPECIFICATIONS .................................................................................................................... 17
COVER SIZING AND PRICING .................................................................................................. 18Cost Considerations ........................................................................................................ 19
All diagrams are for general information. Consult installation instructions for details.
1
TRACK OPTIONS
Underside™ Track• Mounted under deck coping• Anodized aluminum• Easier installation and
replacement of rope
Vinyl-Liner Pool Track Channel• Track channel allows for
custom cantilever profiles• Foam or wood forms can
be incorporated for deck profiles
• Can be used with Cover-Pools Reusable
Coping Form
Vinyl-Liner Pool CopingUndertrack System• For vinyl-liner pools• 90°, 45°, 6" and 24"
corners available• Tracks locked in place
by shims• Standard or bullnose
coping options
Track Channel• For concrete and
fiberglass pools• Raised-wall applications• Track channel allows for
custom cantilever profiles• Foam or wood forms can
be incorporated for deck profiles
actual size
Based on the pool design, choose the appropriate track style and any options.
Reusable Coping Form• For concrete, fiberglass
and vinyl-liner pools• Eliminates the need for
foam or wood forms• Extruded aluminum
Track ChannelInverted Mount• For any deck surface, such
as flagstone, slate or tile, that does not meet basic undertrack mounting conditions (surfaces less than 2" thick or softer materials)
Deck Straps• For porous coping, brick,
flagstone, and materials less than 2" thick
• Mounted every 2' of track• For deck-on-deck pools
Form A
2¾"
4"
Form B
3½"
4"
Deck Material
The Track Channel can be set in a recessed notch below stone or coping level. A light mortar or grout layer can be applied under the stone surface and used to fill in behind channel if necessary.
RECESSED MOUNTING FOR STONE OR COPING
15/8"
11/4"
Form D
4½"
2"
41/4"
2-1/2"
1-1/4"
1
Standard Bullnose
All diagrams are for general information. Consult installation instructions for details.
2
All exposed aluminum extrusions can be painted to match deck color.
SnapTop™ Track• For existing decks• Low profile• Installed on the deck surface• Anodized aluminum• Uses gliders or wheels• Screws are concealed• Standard Universal track
also available• Smaller Slim™ track
available for Step-Saver™ systems
Flush Track - NEW• For new or existing pools• Installed flush with deck• Vinyl-liner, fiberglass or
concrete pools• Anodized aluminum
Universal Deck-Mounted Track• For existing decks• Low profile• Installed on surface of
the deck• Anodized aluminum
Deck-on-Deck PoolsCreate a rectangular frame around the free-form pool for an undertrack installation with track channel.
track channel or deck straps
Extreme CantileverCreate a freeform pool by ex-tending the cantilever up to 24" beyond the channel or track.
track channel or deck straps
2-13/16"
11/16"
Vanishing-Edge Pools
Perimeter Overflow
Create a 45° or 90° vanishing edge
Create a pool for which water height appears even with the deck. A narrow channel collects the overflow water and allows for the glider arms.
600198 ILLUS VAN EDGE 45 DEG COVER OPENING DETAIL - DWG1
Universal track for spas and Step-Saver
45° 90°
Recommended for Indoor use only
2-13/16"
11/16"
1-1/2"
3-1/2" – 4"
Special Construction Applications
All diagrams are for general information. Consult installation instructions for details.
3
A B
no radius cornersat pool wall or coping
C D
excavation from waterline
motor side
lowered pool wall
shaded area=excavation
opposite side
16"36"
18"
excavation from waterline
motor side
Recessed Mechanism—Underside™ Track or Track Channel
1. The tracks (and rectangular pools) must be a true rectangle. The tracks must be perpendicular to the unit mechanism and recessed housing (90°).
2. Over-dig the recessed cover box end of the pool 18" beyond the forms. Do not install plumbing within 14" of the deck in the housing area.
3. The motor can be on either end of the cover box.
4. Do not locate skimmers in the lowered pool wall.
5. All corners must be square (no radius) on the finished tile line or the coping.
6. Place 3" drain in floor or wall of recessed housing.
Pool must be square:AB=CDAD=CB
EXCAVATION AND PLUMBINGConsider any special requirements for excavation and plumbing.
E
F G
Track squared to box or mechanism GE = 6'GF = 8'FE = 10'
2
All diagrams are for general information. Consult installation instructions for details.
4
Recessed Mechanism—Universal, SnapTop™, or Flush Track
The requirements of a recessed mechanism with a deck-mounted track are the same as the undertrack on the previous page. Universal track may be mounted at the pool edge. Flush track must be set back 6" from the pool edge.
C D
A B
Do not locate track on top of a skimmer lid.
16" 36"
motor sidenon-motor side18"
shaded area=excavation
TRACK DIAGONALS: AD=BC
TRA
CK
LEN
GTH
: AC
=BD
TRACK SPACE: AB=CD
1' minimum setback
2' beyond pool
Tracks must be square:AB=CDAD=CB
E
GF
Track squared to box or mechanism GE = 6'GF = 8'FE = 10'
All diagrams are for general information. Consult installation instructions for details.
5
Electric Motor w/ Keyswitch (Standard Equipment)¾ hp Motor with Slip Clutch
Hydraulic Power System(Optional)
3" poly or PVC pipe from housing to power unit.NO SHARP BENDS!
ELECTRICALChoose electric or hydraulic power and controlling devices.
All switches must be mounted in full view of the cover operation.
hydraulic motor 050275 or 050276Hydraulic Pump Unit
electric motor
3WARNING! These are minimum recommendations only. All local and federal codes of standard safe practices must be followed. Refer to the prewiring instructions for detailed instructions and additional mounting options.
Dedicated GFCI
Key Switch 120V
(Hot, Neutral, Ground)
(Neutral, Dir 1, Dir 2, Ground)
Pool
Cover HousingNPT watertight connector 14 AWG Min. Wire extended 8" past conduit end.
Conduit with three different colored wires and one ground.
Conduit to 120 VAC 15 AMP dedicated G.F.C.I.
WARNING! These are minimum recommendations only. All local and federal codes of standard safe practices must be followed.
36" of waterproof flex conduit with 1/2"
14 AWG under 50ft12 AWG over 50ft
14 AWG under 50ft12 AWG over 50ft
MOTOR
POOL
COVER HOUSING
HYDRAULIC MOTOR END
HYD PUMP UNIT
CONDUIT FOR HYDRAULIC HOSEWITH SWEEPING BENDS
LARGE SWEEPING BENDS
Conduit to HYD pump J-box with 2 identified wires and 1 ground
Conduit With (3) 12 AWG (min)Identified Wires plus one ground
Conduit with (4) 18 AWG (min)Identified Wires for CoverLinkWired Control
Option 1:Key Switch KOSA
GreenLED
RedLED Option 2:
CoverLink Wired Control
OR
two 1/2" hosesover 80'
3" conduit
Dedicated GFCI
14 AWG under 50ft12 AWG over 50ft
All switches/control pads must be mounted in full view of the cover operation.
Hydraulic motors must be mounted above ground level.
All diagrams are for general information. Consult installation instructions for details.
6
Auto-Shutoff with Optional Accessory Board/AquaLink®
¾ hp Motor or Hydraulic Motor
Auto-Shutoff with Accessory Board/ AquaLink® and Wireless(Optional) -- ¾ hp Motor or Hydraulic Motor
All control pads must be mounted in full view of the cover operation. Install the accessory board in or by the equipment room or equipment pad, away from the cover housing.
050275 or 050276Hydraulic Pump Unit
All switches/control pads must be mounted in full view of the cover operation.
electric 3/4 hp motor
electric 3/4 hp motor
Hydraulic 1-1/2 hp motor
POOL
COVER HOUSING
Conduit with (3) 18 AWG IdentifiedWires for Low Voltage Key Switch
Option 1:Key Switch 5v
Conduit for Main Power with (3) 14 AWG Identified Wires (Hot, Neutral, Ground)
Conduit with (4) 14 AWG Wires For Power and (3) 18 Awg for Sensors
Conduit with (4) 18 AWG Wires
J-box
#8 Bonding Wire Both Ends
Conduit with (4) 18 AWG (min)Identified Wires for CoverLinkWired Control
GreenLED
RedLED Option 2:
CoverLink Wired Control
OR
Install auto-shutoff away from cover housingin or by equipment room or equipment pad
AS
ACC
Dedicated GFCI
14 AWG under 50ft12 AWG over 50ft
Optional Accessory Board or AquaLink
36" of Waterproof Flex Conduit with 1/2" NPT Water Tight Connector, Extend (4) 14 AWG Wires 8" Past Conduit End
MOTOR
Hydraulic motors must be mounted
above ground level.
Option 1: Auto-shutoff mounted outside housing.
POOL
COVER HOUSING
36" of Waterproof Flex Conduit with 1/2" NPT Watertight Connector for 14 Awg Wire Extended 8" Past Conduit End
Conduit for Main Power with (3) 14 AWGIdentified Wires (Hot, Neutral, Ground)
Auto-shutoff#8 Bonding Wire (Both Sides)
GreenLED
RedLED
CoverLink Wireless Control Pad
Install acc board away from cover housingin or by equipment room or equipment pad
Dedicated GFCI
AS
ACC
14 AWG under 50ft12 AWG over 50ft
Conduit with (4) 18 AWG WiresOptional Accessory Board or AquaLink
Receiver
Antenna
CLE
AR L
INE
OF
REC
EPTI
ON
050275 or 050276Hydraulic Pump Unit
Hydraulic motors must be mounted
above ground level.
All diagrams are for general information. Consult installation instructions for details.
7
Recessed Concrete, Wood, or UPB Box—Underside™ Track
Box Side View—Underside Track
B T [
W
DO
M
conduit 6" maxfrom top of box
conduit should not protrude more than 4" into box
POOLconduit must be on themotor end
3" drain - floor or wallcan be on either end wall cut away for clarity
bond wire
pool beam wall
drain centerline 4" max from end wall
bond wire
Optional coping or condrete build up.
lid
minimum 2" clearance for tracks
MECHANISM HOUSINGChoose a recessed mechanism (concrete or wood box) or deck-mounted mechanism. Systems include a lid assembly, bench frame assembly or fiberglass ends.
Underside Track Box Dimensions for Save-T® 3
MOTORM
OPPOSITEO
BEAMB
THROATT
DEPTHD
WIDTHW
Pools under 55 ft. long x 24 ft. wide
32" 10" 8-12" 2" min tofinished beam
12-1/2" min
12-1/2" min
UPB BOX Pools up to 55 ft. long
32" 10" 8-12" 2" min tofinished beam
13" 13"
Pools over55 ft. long x 24 ft. wide
32" 10" 8-12" 2" min tofinished beam
14½" 14½"
Pools over 65 ft. long or 25 ft. wide and vanishing-edge pools — Call Cover-Pools 1-800-447-2838
4
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
All diagrams are for general information. Consult installation instructions for details.
8
Recessed Concrete, Wood, or UPB Box—Autosave OPTION 1: Conduit comes from back of box.
Underside Track Box Dimensions For Autosave™Up to 13' or 200 square feet
MotorM
OppositeO
BeamB
ThroatT
DepthD
WidthW
Motor Behind 9" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" min
w/ Auto-Shutoff 14-1/2" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" minMotor Below 12-1/2" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" min w/ Auto-Shutoff 12-1/2" min 9" min 10" min 1" to Finished Beam 9"min 14-1/2" min
Note: To avoid interference, run the conduit from the center of the box using flex conduit with 1/2" water tight connector.
POOL
recessed box wall cut away for clarity
M
3" drain - floor or wallcan be on either end
D
B T
W
pool beam wall
Odrain centerline 4" max from end wall
bond wire to bonding grid (route so that cover will not rub or catch or interfere with mechanism)
Conduit comes from center of the housing
MTR
12"
8-1/2"
Conduit
12"
8-1/2"
Conduit
MTR
MTR
12"
8-1/2"
Conduit
12"
8-1/2"
Conduit
MTR
Motor Behind Motor Below
Side View
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
All diagrams are for general information. Consult installation instructions for details.
9
Recessed Concrete, Wood, or UPB Box—Autosave OPTION 2: Conduit comes from side of box.
conduit should not protrude more than 4" into box
conduit must be as close torear wall as possible formechanism clearance.
POOL
3" drain can be on either end
recessed box wall cut away for clarity
pool beam wall
drain centerline 4" max from end wall
MT
OD
B
W
bond wire to bonding grid (route so that cover will not rub or catch or interfere with mechanism)
Underside Track Box Dimensions For Autosave™Up to 13' or 200 square feet
MotorM
OppositeO
BeamB
ThroatT
DepthD
WidthW
Motor Behind 9" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" min
w/ Auto-Shutoff 14-1/2" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" minMotor Below 12-1/2" min 9" min 10" min 1" to Finished Beam 9"min 12-1/2" min w/ Auto-Shutoff 12-1/2" min 9" min 10" min 1" to Finished Beam 9"min 14-1/2" min
MTR
12"
8-1/2"
12"
8-1/2"
Conduit
ConduitMTR
MTR
12"
8-1/2"
12"
8-1/2"
Conduit
ConduitMTR
Motor Behind Motor Below
Side View
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
All diagrams are for general information. Consult installation instructions for details.
10
Deck-Mounted Bench Construction
Deck-Mounted Fiberglass Ends
Three-piece adjustable steel brackets provide a maximum height of 20" by 24" wide. Surface material is not included.
Fiberglass ends are an economical and practical solution to cover the deck-mounted mechanism. Available in white.
roller tube
Recessed Wood Box Construction
Requirements:The material used to construct the box should be:2" x 12" pressure-treated lumber or redwood
Upper trim:2" x 4" pressure-treated lumber or redwood
sideview
sideview
topview
topview
side view
14½"
12½"
14½"
36" 12"24"
12" to
braces
12½"
Also available withstainless-steel base.
16¼"to
17½"
20"
Everlast™ Bench Kit Bench FrameModular bench kit uses adjustable-height brackets and polymer panels to create a low-maintenance bench system.
Available in 4 colors
Recessed Concrete, Wood, or UPB Box—Universal or SnapTop™ Track
B
W
DO
M
POOL
conduit 6" maxfrom top of box
conduit should not protrude more than 4" into box
conduit must be on themotor end
3" drain - floor or wallcan be on either end wall cut away for clarity
bond wire
pool beam wall
drain centerline 4" max from end wall
bond wire
Deck Mount Track Box Dimensions for Save-T® 3
MOTORM
OPPOSITEO
BEAMB
THROATT
DEPTHD
WIDTHW
Pools under 55 ft. long x 24 ft. wide 32" 10" 8-12" 2" min to finished beam 12½" min 12½" min
UPB BOX Pools up to 55 ft. long 32" 10" 8-12" 2" min to finished beam 13" 13"
Pools over 55 ft. long x 24 ft. wide 32" 10" 8-12" 2" min to finished beam 14½" 14½"
Pools over 65 ft. long or 25 ft. wide and vanishing-edge pools — Call Cover-Pools 1-800-447-2838
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
All diagrams are for general information. Consult installation instructions for details.
11
Coping or Deck Requirements—Underside track
• All corners of the coping must be square• Minimum 2" cantilever from tile
on side walls• Minimum 3" cantilever from tile
on end wall opposite the mechanism
Gunite Layout—Underside™ track
At the recessed box end, the pool wall (bond beam) must be shot 2½" (2" finished with tile) lower than the side walls.
The top inside pool corners (above the waterline) must be square, not radius.
Any interior wall, such as for spas, also must be gunited 2½" (2" finished with tile) lower than the side walls.
form
2½" lower
side wall
coverbox
bondbeam
top of side wall
2½" lower than side wall
COPING AND DECKConsider the requirements for coping and deck installation.
side wall
interior wall
form
form
brace
2" offsetin steel
16 d nails
no radius corners
2" cantilever sidewalls
lowered pool wall
motor
3" cantilever
5
All diagrams are for general information. Consult installation instructions for details.
12
Tile Beam—Underside track
1/4" round edge if exposed
1/4" round edge
POOL
DECK
2" min.
2" min.
The lowered pool wall is finished with a tile surface.
For the lowered wall edge, use a rounded tile on the front and back edges to minimize scraping on the cover.
NOTE: The track must be mounted on the flat bottom of the coping. The coping measurement is NOT the track space. Coping must not extend more than ½" past the edge of the track.
Track Space
2" cantilever box minimum12 ½" wide x 12 ½" deep Pool wall
2" min.
bull nose
Bull nose
2" minimumfrom tile
decking
Decking
DECKING
POOL WALL
2" min
2" minfrom tile
TRACK SPACE
Coping or Deck Requirements—Underside track (cont.)
Opening 2" finished with tile or other material
Opening for the track must be 2½" at box (2" finished with tile), sloping to 3" inside pool
1/4" round edge
All diagrams are for general information. Consult installation instructions for details.
13
Vanishing Lid Adjustable 12"Stainless-Steel Bracket• For any tray less
than 18"• Extensions 14½" & 17½"
available
Note: The deck thickness must be increased for extended trays if the leading edge is going to fit under the tray. Contact Cover-Pools for more information.
The maximum width of any tray is 24".The maximum length of tray is 24".
Walk-On Vanishing LidThis design offers an adjustable tray support system for any type of deck material. Stainless-steel or aluminum trays and stainless-steel brackets provide the support base for a strong walk-on lid that can blend with the surrounding deck.
Vanishing Lid Adjustable 18"Stainless-Steel Bracket• Maximum bracket
spacing is two feet• For trays 18-24" wide• Extensions 20½" & 23½"
available
Standard Aluminum Lid Tilted Bracket for Universal, Snaptop™, and Flush Track• Stepped or tilted anodized
aluminum lid available with 4" or 6" hinge
Flush Mount Lid for vinyl liner pools with UPB Box
NOTE:Walk-on Vanishing Lid systems require a concrete housing, or, if using a wood housing, a concrete wall must be poured behind the box for anchoring brackets.
Brackets
Vanishing Lid™ System
Bezel™ lids
Flat Bezel Lid Tilted Bezel Lid Stepped Bezel Lid
RECESSED BOX COVERChoose lid and brackets to cover recessed box.
Standard Aluminum Lid Flat Bracket for Underside™ Track• Standard anodized
aluminum lid available with 4" or 6" hinge
18" max. 24" max.tray or stone tray or stone
3/8" 1½
600104 ILLUS VANISHING LID CORNER BRACKET - DWG1.ai 600104 ILLUS VANISHING LID CORNER BRACKET - DWG1.ai
6" Min
1½
6
Available in 16" or 18" widthAvailable in 16" width with 16" or 18" ends
All diagrams are for general information. Consult installation instructions for details.
14
SPECIFICATIONSReview system details for Save-T® covers.7
Quad-core™ Fabric• Material: PVC vinyl, laminated over a reinforced
polyester mesh for strength and tear resistance• Rigorously Tested: The exclusive formula is the
product of 50 years of testing and experience• Designed for the Pool Environment: UV, mildew,
and pool-chemical resistant with superior dimensional stability
• Weight: 18 oz. per square yard• Thickness: 28 mil laminated vinyl• Strength: Exceeds the ASTM F1346-91 minimum
standard of 485 lbs. per 4' radius• Construction: Fabric is attached to webbing and
low-stretch rope (70,000+ cyclic loading fatigue life) with double-sewn Dabond® bonded polyester thread for durability
• 11 standard colors: dusky blue, royal blue, light blue, aqua, forest green, beige, tan, brown, gray, slate gray, and black
• Additional special-order colors available• 7- year limited prorated standard warranty• Sewn webbing in 9 optional colors• Optional Ultimate™ heat sealed webbing in 6 colors• Optional Ultimate™ rope (100,000+ cyclic loading
fatigue life) or Stainless steel cable
Track Styles• 7-year limited warranty on all aluminum extrusions• All aluminum extrusions are 100% anodized• Underside™, SnapTop™, Universal, Slim™, or Flush
track• Safety-Lock track channel• Top-mounted track channel for concrete and
fiberglass pools• Inverted track channel for concrete or
deck-on-deck applications• Track channel system for vinyl pools• Coping channel for vinyl pools• V-Pak™ kit for vinyl pools (includes system, fabric,
channel, box, and lid)• Reusable coping forms (3 Profiles)• 45-degree vanishing-edge pools• 90-degree vanishing-edge pools• NEW Corr-Resist™ non-metallic Track Channel
Mechanism• Exclusive Corr-Resist end hubs with stainless steel,
designed for salt water systems• Marine-grade anodized aluminum frame and bracket• Limited lifetime warranty• Exclusive positive-shift system• Exclusive Corr-Resist rope reel with stainless steel side
plates designed for quiet operation• Standard electric system comes with either the slip
clutch or auto-shutoff
Mechanism Housing• Standard 12" aluminum lid with either 4" or 6" hinge• Bezel™ lids, 16" and 18" wide• Vanishing Lid™ trays, 12"–24" wide with stainless-steel
trays and stainless-steel adjustable brackets• Fiberglass deck-mounted mechanism end housings• Ultimate™ Polymer recessed box • Everlast™ modular bench kit (available in 4 colors)• Bench frame assembly
Power and Controls• 3-year limited warranty on all electrical• 3/4 hp waterproof electric motor
Optional Ultimate™ High-Torque Motor• 1 ½ hp/2000 PSI hydraulic system• Safety lockout key control • CoverLink™ touchpad control (wired or wireless)• Low-voltage auto-shutoff with key switch• Water-feature shutoff• Jandy iAquaLink™ Interface
Safety• Exceeds ASTM F1346-91 requirements• Full UL listing• Bonding included with all automatic systems• Automatic water-removal cover pump included
• NOTE:Some cover manufacturers treat cover pumps and bonding as options for their systems. A solid safety cover without a pump is NOT approved to ASTM F1346-91 safety standards. The installation of an automatic cover system without bonding is not a UL-listed product.
Other Options• Painting—all extrusions can be painted to match most
deck surfaces or fabric colors
All diagrams are for general information. Consult installation instructions for details.
15
Track Space Track Space
Pool Length
Mechanism 1'
2'
Pool Length
Track Space
Mechanism
1'
Pricing based on motor mechanism being installed one foot from pool edge, motor position on left or right.
TRACK SPACE x POOL LENGTH=COVER SQUARE-FOOT PRICING
Track widths over 25' or lengths over 65' require factory approval (maximum track space is 36').
Undertrack Deck-Mounted Track
COVER SIZING AND PRICINGDetermine pricing according to the cover specifications.8
All diagrams are for general information. Consult installation instructions for details.
16
Cost Considerations
Excavation/Plumbing q Housing excavation q 3" drain for housing drain— drain to air or drain to pit
q 3" conduit for hydraulic-unit housing
Electrical q 1/2" Conduit for mechanism power q Electric run to key switch q 15-amp GFCI dedicated circuit for mechanism at panel (20 AMP for hydraulic)
q Electric runs over 50' require heavy-gauge wire q Electrical run for accessory board q 1/2" Conduit (for low voltage wires) required with Auto-shutoff/CoverLink wired controls
Concrete q Concrete, gunite or shotcrete box, minimum 6" thick, 3500 PSI, (no rebound)
q Additional deck around housing/mechanism q Tile on lower beam, beam cover or other
Cover/Mechanism q Unit price based on track space x pool length including steps, plus options
q Track space 25' 6" or more may require a larger main mechanism tube and larger leading edge for fabric
TrackUnderside™ track or Universal track standard
q Track channel for concrete or fiberglass pools (2 or 3 sided)
q Flush track q SnapTop™ track q Vinyl-liner pool coping 90°, 45°, 6" radius or 24" radius
q Track channel for vinyl-liner pools q Vanishing edge 45° or 90° q Painted track extrusions
HousingAluminum lid, bench frame or fiberglass ends standard
q Painted lid extrusions q Aluminum Lids: Standard, Bezel™ lids, or Flush Mount q Walk-on Vanishing Lid™ trays q Bench for deck-mounted mechanism
Power/Controls110 V motor and hard-wired 3-wire key standard
q Auto-shutoff control with amp limit q Wireless CoverLink™ digital touchpad control q Wired CoverLink digital touchpad control q Water-feature shutoff/accessory board q Hydraulic pump with hydraulic hoses q Jandy iAquaLink™ interface & control
SAVE-T® 3 “B
IG R
ED”
SLIP C
LUTC
H·
stainless-steel and aluminum
construction
· long-w
earing industrial-grade friction m
aterial (not plastic)·
waterproof and tem
perature-proof operation
· no replacem
ent parts needed·
lifetime w
arranty
AquaLink
® interface Board
·
cover status controls pool features
· view
if cover is open/closed·
reduce the filter pump tim
e·
adjust AquaP
ure output·
turn off water features, lights,
and booster pump
cleaners when the
pool is covered. ·
connect to an iPhone
with the iA
uquaLink™
EXC
LUSIVE!
HYB
RID
EN
D H
UB
with
CO
RR
-RE
SIST™ com
ponents·
stainless steel and C
orr-Resist™
components
· designed for m
ineral sanitizing system
s ·
minim
izes salt corrosion·
can be retrofitted to previous m
odels
EXC
LUSIVE!
MA
RIN
E-GR
AD
E A
NO
DIZE
D R
OLLE
R D
RU
M·
strong 17 gauge thick alum
inum tube
· 6" &
8" diameters available
· anodized alum
inum
protects against corrosion and oxidation
PO
SITIVE SHIF
T SYSTEM
· all stainless-steel shaft and shifting-dog com
ponents·
no shear pins or bolts·
3/8" solid stainless-steel drive dow
el
NE
W G
LIDE
R STO
P·
prevents glider from
running past the track·
ensures cover stops in correct position
· attaches to track
RO
LLER
TUB
E BR
AK
E·
stainless-steel brake adjuster
· easy to adjust
· keeps cover taught
3/4 hp WATER
PR
OO
F MO
TOR
· 3/4 hp, 41 rpm
, 1600 in-lbs of torque
· capacitor-start, capacitor-run
· O
-ring sealed and potted w
ire-entry points·
stainless-steel gears with
sealed permanent grease
· U
L Listed·
Optional U
ltimate™
High-
Torque Motor 3/4 hp, 27 rpm
, 1375 in-lbs of torque
CO
VER
LINK
™ C
ON
TRO
L·
10-number w
ireless or w
ired touch pad·
wireless system
s use secure FM
-radio technology w
ith signal lock
· fits in a single gang box
· uses A
A batteries
WEB
BIN
G STO
P B
LOC
K·
simple installation to set
cover travel length·
clamp design allow
s easy adjustm
ent
KE
Y SW
ITCH
· 3-wire key sw
itch for sim
ple wiring
· m
ounts in standard sw
itch box·
NE
W brushed stainless
steel faceplate (high-voltage only)
QU
AD
-CO
RE™
18oz FA
BR
IC CO
LOR
S·
dusky blue·
royal blue·
light blue·
aqua·
forest green·
beige·
tan·
brown
· gray
· slate gray
· black
· O
ptional colored webbing
or Heat S
ealed Webbing
EXC
LUSIVE!
HYB
RID
RO
PE R
EE
L w
ith CO
RR
-RE
SIST™
components
· Exclusive EZ-Lock rope reel
system for sim
ple cover alignment
· choose betw
een ratcheting or locked rope reels
· easy adjustm
ent on out-of-square pools
· sim
ple adjustment of cover alignm
ent·
simple change-over to locked
or unlocked reels·
can be retrofitted to previous models
AU
TO-SH
UTO
FF W
ITH A
MP
LIMITE
R·
compact potted w
aterproof design·
adjustable amp lim
iter overload safety circuit
· LED
indicator and diagnostic lights·
optional water-feature control
board (can control 12- and 24-volt m
otorized valves or pum
p motors up to 30
amps)
LOW
-STRETC
H R
OP
E·
70,000 cycle loading fatigue life·
attached with double-sew
n, D
abond® bonded polyester
thread.
ULTIM
ATE™ R
OPE
· 100,000 cycle loading fatigue life
STAIN
LESS STEEL CA
BLE
· superior durability in a pool environm
ent·
does not stretch or shrink, reducing realignm
ent service calls
top related