samsung shark user guide
Post on 06-May-2017
217 Views
Preview:
TRANSCRIPT
Simplified operation instructions for Samsung Shs-2320 “Shark”
(this manual is unofficial and translated version only)
Registering Pin Number
Perform this operation during door unlocked status
1. Press [Register button] (located at the battery compartment, remove
cover)
2. Enter PIN number to be registered (4~12 digits)
3. Press Button
Registering Card/Key tag
1. Press [Register button]
2. Place the card/key tag to be registered on the sensor
3. Press [Register button] again
Opening The door using Pin number (outside)
1. Place palm slightly on the [number pad]
2. When the number pad lights up, enter your Pin on the number pad
3. Press .
*Double-Security mode
1. Place palm slightly on the [number pad]
2. When the number pad lights up, press the two random number that will
appear on the screen
3. Enter Pin on the number pad
4. Press button.
Opening the door (outside)Card/Keytag
1. Place palm slightly on the [number pad]
2. When the number pad lights up, place card/key tag on the sensor
Opening/closing the door from the inside
Automatic Lock Mode
1. On the main body inside press [열림/닫힘] (open/close) button
and the door will be lock or unlock
Manual Lock mode
1. On the main body inside, Turn the manual switch knob to open or
close, exposing green color indicates open status while red color
indicates closed status
Double/Normal Security mode setting
1.Press [register button] inside
2.Press [7] to set Double security Mode on the number pad or
3.Press [9] to set Normal lock mode on the number pad
4.Press button
Setting Authentication Sensor
1.Press [register button] inside
2.Press [1] to enable Authentication Sensor on the number pad or
3.Press [3] to disable Authentication Sensor on the number pad
4.Press button
Setting Double authentication mode
1.Press [register button] inside
2.Press [4] to enable Double Authentication mode on the number pad or
3.Press [6] to disable Double Authentication mode on the number pad
4.Press button
Setting Automatic Lock/Mabual lock Mode
1. On the main body inside switch automatic/manual lock mode
By switching switch
Adjusting Volume (Setting Sound)
1. On the main body inside, adjust sound by the following setting
[1] Mute [2] Normal [3] Loud
Cancelling Alarms
Invalid entry alarm – (in case of multiple wrong password/card/key tag
entry)
1. On the main body press [register] button or [open/close] button
2. Outside, press Pin followed by on the number pad, or place
card/key tag on the sensor
Intrusion alarm (outside)
1. On the main body press [register] button or remove one battery
2. Outside, press Pin followed by on the number pad, or place
card/key tag on the sensor
How to use Emergency Battery
1. Using a 9V battery, make a contact by placing the 9V battery in an
upward position connecting the polarity with the terminal node.
2. In this status you can now enter your Pin number, or place key tag/card
To initialize the unit (refer to the illustrations)
Battery replacement
*Average Battery Lifetime
1.5V alkaline AA x 4 (ave. 10 operations per day) 1 year
Please use alkaline battery only Replace Battery notification
The battery icon will be lighted red and an alarm will go off signaling the
need to replace battery.
Please change the battery at this time
*please observe correct polarity placement when changing battery
*please check battery for damage and leaks before changing
*replace battery all at once, do not replace with used or mix new with old
used ones. (Refer illustrations below)
On the main body press the Battery cover release button, lift the cover up
And replace the battery in this manner.
Trouble Shooting
No power
-check battery, if inserted correctly or check if in good condition Registration problem
(PIN)
-When registering please make sure to register pin within the 10 seconds
time frame, when registration failed, try registering again.
-check battery power if sufficient (CARD/KEYTAG)
When registering card/keytag please make sure to register pin within the
10 seconds time frame, when registration failed, try registering again Door not unlocking
Even after entering password and pressing [*] button
-Make sure the password is registered first before trying to use.
-Enter password when the number pad is lighted
(slightly touch number pad first ,when activated, enter pin number) Even after using Card/key tag to open door
-Make sure the Card/key tag is registered first before trying to use
-You should place the Card/key tag on the sensor correctly If double-lock feature is activated, you cannot open the door by
password or key tag or card only
When double-lock feature is enabled, you have to place palm slightly on
the number pad first to activate, wait for the (bee~ree~reep sound) and
then you can place card or key tag on the sensor to unlock the door.
for instance the unit is not responding despite standard procedure
is done, the unit may be defective and you should contact service
center.
Auto-relock function not working
- make sure you have set the unit to automatic lock mode
- when set to manual mode, after closing the door, touch slightly the
number pad, to initialize relock.
*this event can also happen if the unit is installed incorrectly,
for instances like these, please contact service center.
* If the battery is completely discharged, the automatic lock feature does
not work, please check power supply if sufficient.
Number Pad is not activating
-on the front body outside, beside the Power on/off button, press the
“reset” button with a pin.
*after standard procedure is done, but unit still not responding,
contact service center
Operation summary
Pin registration/modify
1. Register button + enter pin + button Card/Keytag registration
1. Register button + place card/keytag on the sensor + register
button again
Opening door from inside
1. (Automatic) in locked status, press +open door
2. (Manual) turn manual lock knob to unlock position + open door
Closing door from inside
1. (Automatic) press and the door will be locked
2. (Manual) turn manual lock knob to lock position and door will be locked
Opening the door from the outside
Double security mode
Card/key tag – touch number pad + place card/key tag on the sensor.
Pin - touch number pad + press the 2 random number that will appear +
enter Pin number + button
Closing the door from the outside
Automatic Lock – after closing the door, the automatic lock will activate
Manual Lock – touch number pad slightly, and the door will be locked
Setting double security mode
On Safe mode – register button + 7 +
On normal mode - register button + 9 +
How to enable/disable double authentication mode
Enable - register button + 4 +
Disable - register button + 6 +
Setting Automatic/Manual Lock mode
Automatic- [자동/수동잠김] switch to “automatic”
Manual - [자동/수동잠김] switch to “manual”
Setting Sound volume
Adjust volume setting from low, normal &
loud
Enable/disable Authentication Sensor
Enable - register button + 1 +
Disable - register button + 3 +
Setting anti-hack feature
Enable- after closing the door, press button
Disable-enter password, or place key tag/card on sensor.
Turn-off alarm(inside)
Press register button
Turn-off alarm(outside)
Enter Pin or place card/key tag on the
sensor
top related