renovation of hostel 'e' block of national … · steel work 9.200 19 providing and...
Post on 14-Aug-2018
215 Views
Preview:
TRANSCRIPT
Total Amount(
Rs.)
1 2 3 4 5= (3 x 4 ) 3 + 5
In figures In words In figures In words
1 CIVIL WORKS
As per DSR 2012/Market Rate
(a) EARTH WORK 1568.56
(b) CONCRETE &RCC Work 250373.68
(C) BRICK WORK 65779.94
(d) MARBLE AND GRANITE WORK 46723.64
(e) Joinery Work 1389573.80
(f) Steel Work 2618508.15
(g) Flooring Work 2167060.35
(h) Finishing Work 1163641.86
(i) Demolishing Work 204416.28
(j) Aluminium Work 419053.04
(k) Water proofing Work 1004985.44
(l) Market Rate Items(Flooring) 2156863.56
2 Electrical Work 5467804.84
3 SANITARY & PLUMBING WORKS 2535430.00
4 Fire Fighting Work 281864.0019773647.00 TENDER VALUE
TOTAL TENDER VALUE ( IN WORDS) : Rupees
Seal & Signature of Tenderer
Total
RENOVATION OF HOSTEL 'E' BLOCK OF NATIONAL INSTITUTE OF TECHNOLOGY, CAMPUS, RAIPUR
PRICE SCHEDULE
SI. No. DESCRIPTION
ESTIMATED
COST (Rs.)
TO BE QUOTED BY TENDERER
% ( - ) Below / At ParAmount ( - ) Below / At Par
Estimated Cost
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
EARTH WORK
1.1.1 1 Carriage of material by mechanical Transport
including loading ,unloading and stacking of Lime,
moorum, building rubbish up to 5 km Cum 5.60 122.46 686.12
2.800 2 Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or
10 sqm on plan) including dressing of sides and
ramming of bottoms, lift upto 1.5 m, including getting
out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m. cum 5.60 157.50 882.44
2.8.1 All kinds of soil
1568.56
CONCRETE WORK
4.170 3 Making plinth protection 50mm thick of cement
concrete 1:3:6 (1 cement :3 coarse sand : 6graded
stone aggregate 20mm nominal size) over 75mm bed
by dry brick ballast 40mm nominal size well rammed
and consolidated and grouted with fine sand
including finishing the top smooth sqm 157.50 419.30 66039.75
REINFORCED CEMENT CONCRETE
FORM WORK
5.900 4 Centering and shuttering including strutting, propping
etc. and removal of form for :
5.9.3 b Suspended floors, roofs, landings, balconies and
access platform. sqm 11.34 40.65 460.97
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
5.9.5 c Lintels, beams, plinth beams, girders, bressumers and
cantilevers. sqm 303.80 332.15 100907.17
STEEL REINFORCEMENT
5.220 5 Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position
and binding all complete. kg 642.92 68.10 43782.51
5.22.6 Thermo-Mechanically Treated bars.
DESIGN MIX CONCRETE
5.330 6 Providing and laying in position machine batched and
machine mixed design mix M-25 grade cement
concrete for reinforced cement concrete work, using
cement content as per approved design mix, including
pumping of concrete to site of laying but excluding
the cost of centering, shuttering, finishing and
reinforcement, including admixtures in recommended
proportions as per IS: 9103 to accelerate, retard
setting of concrete, improve workability without
impairing strength and durability as per direction of
Engineer-in-charge.
(Note :- Cement content considered in this item is @
330 kg/cum Excess/less cement used as per design
mix is payable/recoverable separately).5.33.2 a All works above plinth level upto floor V level cum 5.59 7014.55 39183.28
250373.68HALF BRICK MASONRY
6.130 7 Half brick masonry with F.P.S. bricks of class
designation 7.5 in superstructure above plinth level
up to floor V level.
6.13.2 Cement mortar 1:4 (1 cement : 4 coarse sand) sqm 89.46 665.80 59562.47
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
6.150 8 Extra for providing and placing in position 2 Nos.
6mm dia. M.S. bars at every third course of half brick
masonry (with F.P.S. bricks). sqm 89.46 69.50 6217.47
65779.94Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
MARBLE & GRANITE WORK
8.200 9 Providing and fixing 18 mm thick gang saw cut,
mirror polished, premoulded and prepolished,
machine cut for kitchen platforms, vanity counters,
window sills , facias and similar locations of required
size, approved shade, colour and texture laid over 20
mm thick base cement mortar 1:4 (1 cement : 4
coarse sand), joints treated with white cement, mixed
with matching pigment, epoxy touch ups, including
rubbing, curing, moulding and polishing to edges to
give high gloss finish etc. complete at all levels.8.2.2 Granite of any colour and shade
8.2.2.2 a Area of slab over 0.50 sqm sqm 11.34 3907.40 44309.92
8.600 10 Mirror polishing on marble work/Granite work/stone
work where ever required to give high gloss finish
complete. sqm 11.34 212.85 2413.72
46723.64ANODISED ALUMINIUM FITTINGS (ALL
FITTINGS SHALL BE ISI MARKED)9.830 11 Providing and fixing IS : 3564 marked Aluminium
die cast body tubular type universal hydraulic door
closer with necessary accessories and screws etc. Each 48.00 753.75 36180.00
9.960 12 Providing and fixing aluminium sliding door bolts ISI
marked anodised (anodic coating not less than grade
AC 10 as per IS : 1868) transparent or dyed to
required colour or shade with nuts and screws etc. Each 96.00 229.65 22046.00
9.96.1 300x16 mm
9.100 13 Providing and fixing aluminium handles ISI marked
anodised (anodic coating not less than grade AC 10
as per IS : 1868) transparent or dyed to required
colour or shade with necessary screws etc. complete :
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
9.100.1 a 125 mm each 120.00 69.80 8376.00
9.100.2 b 100 mm each 96.00 55.10 5289.60
9.101 14 Providing and fixing aluminium hanging floor door
stopper ISI marked anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or
dyed to required colour and shade with necessary
screws etc. complete.
9.101.2 Twin rubber stopper each 48.00 83.95 4029.60
9.103 15 Providing and fixing bright finished brass 100 mm
mortice latch and lock ISI marked with six levers and
a pair of anodised (anodic coating not less than grade
AC 10 as per IS : 1868) aluminium lever handles
with necessary screws etc. complete (Best make of
approved quality). each 48.00 815.45 39141.60
9.108 16 Providing and fixing PTMT Tower Bolts with 12 mm
one piece rod inside and necessary screws etc.,
complete.
9.108.1 a 152x42x18 mm weighing not less than 60 gms each 150.00 88.50 13275.00
9.108.2 b 202x42x18 mm weighing not less than 78 gms each 120.00 113.65 13638.00
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
9.119 17 Providing and fixing factory made P.V.C. door frame
of size 50x47 mm with a wall thickness of 5 mm,
made out of extruded 5mm rigid PVC
foam sheet, mitred at corners and joined with 2 Nos
of 150 mm long brackets of 15x15 mm M.S. square
tube, the vertical door frame profiles to be reinforced
with 19x19 mm M.S. square tube of 19 gauge, EPDM
rubber gasket weather seal to be provided through out
the frame. The door frame to be fixed to the wall
using M.S. screws of 65/100 mm size, complete as
per manufacturer’s specification and direction of
Engineerin-Charge. m 396.00 458.95 181744.20
9.124 18 Providing and fixing factory made 30 mm thick door
shutter made of solid PVC foam profile. The styles &
rails shall be of size 75 mm x 30 mm having wall
thickness 5 mm. The styles, top & bottom rails shall
have one side wall thickness of 15 mm integrally
extruded on the hinge side of the profile for better
screw holding power. The styles and rails shall be
reinforced with M.S. tubes of size 33 mm x 17 mmx
1 mm, painted with primer , all four corners of
reinforcement to be welded or sealed. Solid PVC
extruded bidding (push fit type) will be set inside the
styles and the rails with a cavity, to receive single
piece extruded 5 mm PVC sheet as panel. The styles
and rails will be mitred cut and joint with the help of
PVC solvent cement & self driven self tapping
screws. Single piece extruded solid PVC lock rail of
size 100 mm x 30 mm with wall thickness 5 mm &
15 mm integrally extruded in the middle of the lock
rail & fixed with styles with the help of PVC solvent
cement & self driven self tapping screws of size 100
mm x 8 mm complete as per manufacturer's
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
9.124.1 a Non decorative finish sqm 396.00 2691.55 1065853.80
#########STEEL WORK
9.200 19
Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) decorative type, core
of block board construction with frame of 1st class
hard wood and well matched teak 3 ply veneering
with vertical grains or cross bands and face veneers
on both faces of shutters.
9.20.135 mm thick including ISI marked Stainless Steel butt
hinges with necessary screws sqm 159.12 2,606.45 414738.32
9.480 20
Providing and fixing M.S. grills of required pattern in
frames of windows etc. with M.S. flats, square or
round bars etc. including priming coat with approved
steel primer all complete.
9.48.2Fixed to openings /wooden frames with rawl plugs
screws etc. kg 5562.42 116.90 650246.41
10.140 21 Providing and fixing pressed steel door frames
conforming to IS: 4351, manufactured from
commercial mild steel sheet of 1.60 mm thickness,
including hinges, jamb, lock jamb, bead and if
required angle threshold of mild steel angle of
section 50x25 mm, or base ties of 1.60 mm, pressed
mild steel welded or rigidly fixed together by
mechanical means, including M.S. pressed butt
hinges 2.5 mm thick with mortar guards, lock strike
plate and shock absorbers as specified and applying
a coat of approved steel primer after pre-treatment
of the surface as directed by Engineerin-charge:10.14.2 Profile C10.14.2.1 Fixing with carbon steel galvanised dash fastener of
required dia and size (to be paid for separately) m 2361.60 400.95 946883.52
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
10.110 22 Providing and fixing factory made ISI marked steel
glazed doors, windows and ventilators, side /top
/centre hung, with beading and all members such as
F7D, F4B, K11 B and K12 B etc. complete of
standard rolled steel sections, joints mitred and flash
butt welded and sash bars tenoned and riveted,
including providing and fixing of hinges, pivots,
including priming coat of approved steel primer, but
excluding the cost of other fittings, complete all as
per approved design, (sectional weight of only
steel members shall be measured for payment).
10.11.1 Fixing with 15x3 mm lugs 10 cm long embedded in
cement
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement
: 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size) kg 5314.41 114.15 606639.90
######### FLOORING
11.260 22 Kota stone slab flooring over 20 mm (average) thick
base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab,
including rubbing and polishing complete with base
of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26.1 25 mm thick sqm 1760.26 1141.40 2009159.62
11.310 23 Extra for pre finished nosing in treads of steps of
Kota stone/ sand stone slab. Rm 75.60 75.80 5730.48
11.320 24 Extra for Kota stone/ sand stone in treads of steps and
risers using single length up to 1.05 metre . sqm 35.05 16.90 592.28
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
8.02 11.2 Providing and fixing 10 mm thick acid and/or alkali
resistant tiles of approved make and colour using acid
and/or alkali resisting mortar bedding, and joints filled
with acid and/or alkali resisting cement as per
IS : 4457, complete as per the direction of Engineer-
in- Charge.11.21.2.1 Acid and alkali resistant tile R/o Sqm 1259.85
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
CERAMIC GLAZED TILES
11.360 25 Providing and fixing Ist quality ceramic glazed wall
tiles conforming to IS: 15622 (thickness to be
specified by the manufacturer), of approved make, in
all colours, shades except burgundy, bottle green,
black of any size as approved by Engineer-in-Charge,
in skirting, risers of steps and dados, over 12 mm
thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg
per sqm, including pointing in white cement mixed
with pigment of matching shade complete. sqm 67.62 836.65 56574.27
12.100 26 Providing corrugated G.S. sheet roofing including
vertical / curved surface fixed with polymer coated J
or L hooks, bolts and nuts 8mm diameter with
bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead, including a coat of
approved steel primer and two coats of approved
paint on overlapping of sheets complete (up to any
pitch in horizontal/ vertical or curved surfaces),
excluding the cost of purlins, rafters and trusses and
including cutting to size and shape wherever 12.1.3 0.63 mm thick with zinc coating not less than 275
gm/ m² sqm 84.55 743.45 62858.70
12.400 Providing ridges or hips of width 60 cm overall width
plain G.S. sheet fixed with polymer coated J. or L
hooks, bolts and nuts 8 mm dia G.I. limpet and
bitumen washers complete.
12.4.2 0.63 mm thick with zinc coating not less than 275
gm/m² M 30.00 502.75 15082.50
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
12.110 Extra for providing and fixing wind ties of 40x 6 mm
flat iron section. M 150.00 113.75 17062.50
#########FINISHING
CEMENT PLASTER (IN FINE SAND)
13.100 27 12 mm cement plaster of mix :
13.1.1 1:4 (1 cement : 4 fine sand) sqm 174.34 163.35 28478.77
13.200 28 15 mm cement plaster on the rough side of single or
half brick wall of mix :
13.2.2 1:6 (1 cement: 6 fine sand) sqm 174.34 172.80 30126.31
13.480 29
finishing with deluxe multi surface paint syestem for
imteriors and exterier using primer as manufacturur
specification;
13.48.2
painting wood work with deluxe multi surface paint
of required shade.two or more coat
applied@0.90ltr/10 sqm over an under coat of primer
applied@0.75/10 ltr sqm of approved brand and sqm 454.37 88.2 40074.99
13.520 30
Finishing with Epoxy paint (two or more coats) at all
locations prepared and applied as per manufacturer's
specifications including appropriate priming coat,
preparation of surface, etc. complete.
13.52.1 On steel work sqm 454.37 116.55 52956.24
INTERIOR FINISHING
13.410 31 Distempering with oil bound washable distemper of
approved brand and manufacture to give an even
shade :
13.41.1 New work two coats over and including priming coat
with cement primer. sqm 3749.87 89.70 336363.68
EXTERIOR FINISHING
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
13.800 32 Providing and applying white cement based putty of
average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete. sqm 5359.84 89.65 480509.50
13.470 33 Finishing walls with Premium Acrylic Smooth
exterior paint with Silicone additives of required sqm 1609.96 94.95 152866.12
13.47.1 New work (Two or more coats applied @ 1.43 ltr/ 10
sqm over and including priming coat of exterior
primer
13.620 34 Painting with synthetic enamel paint of approved
brand and
manufacture of required colour to give an even shade
13.62.1 Two or more coats on new work over an under coat
of
suitable shade with ordinary paint of approved brand
and sqm 397.80 106.25 42266.25
#########DEMOLISHED ITEM
15.700 35 Demolishing brick work manually/ by mechanical
means including stacking of serviceable material and
disposal of unserviceable material within 50 metres
lead as per direction of Engineer-in-charge.
15.7.4 In cement mortar Cum 5.60 754.10 4225.07
15.120 36 Dismantling doors, windows and clerestory windows
(steel or wood) shutter including chowkhats,
architrave, holdfasts etc. complete and stacking
within 50 metres lead :
15.12.1 a Of area 3 sq. metres and below each 107.54 141.25 15189.32
15.12.2 b Of area beyond 3 sq. metres each 15.30 193.85 2965.91
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
15.230 37 Dismantling tile work in floors and roofs laid in
cement mortar including stacking material within 50
metres lead.
15.23.1 For thickness of tiles 10 mm to 25 mm sqm Sq.m 567.79 28.20 16011.55
15.260 38 Demolishing brick tile covering in terracing including
stacking of serviceable material and disposal of
unserviceable material within50 metres lead. Sq.m 464.06 40.80 18933.62
15.270 39 Demolishing mud phaska in terracing and disposal of
material within 50 metres lead. Cu.m 46.41 334.60 15527.42
15.420 40 Dismantling C.I. or asbestos rain water pipe with
fittings and clamps including stacking the material
within 50 metres lead :
15.42.2 a 100 mm dia pipe RM 240.00 28.60 6864.00
15.560 41 Dismantling old plaster or skirting raking out joints
and cleaning the surface for plaster including disposal
of rubbish to the dumpingground within 50 metres Sq.m 1463.60 20.05 29345.26
14.430 42 Removing white or colour wash by scrapping and
sand papering and preparing the surface smooth
including necessary repairs to scratches etc. complete Sq.m 3408.98 7.60 25908.22
16.680 43 Providing and laying 60mm thick factory made
cement concrete interlocking paver block of M -30
grade made by block making machine with strong
vibratory compaction, of approved size, design &
shape, laid in required colour and pattern over and
including 50mm thick compacted bed of coarse sand,
filling the joints with fine sand etc. all complete as
per the direction of Engineer-in-charge. sqm 115.32 602.20 69445.91
204416.28Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
ALUMINIUM WORK
21.300 44 Providing and fixing glazing in door, window,
ventilator shutters and partitions etc. with EPDM
rubber / neoprene gasket etc. complete as per the
architectural drawings and the directions of engineer- sqm 307.85 1054.20 324530.20
21.3.2 With float glass panes of 5.50 mm thickness
21.100 45 Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded
built up standard tubular sections/ appropriate Z
sections and other sections of approved make
conforming to IS: 733 and IS : 1285, fixed with rawl
plugs and screws or with fixing clips, or with
expansion hold fasteners including necessary filling
up of gaps at junctions, at top, bottom and sides with
required EPDM rubber/neoprene gasket etc.
Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap
beading for glazing / paneling, C.P. brass / stainless
steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge. 21.1.1 a For fixed portion
21.1.1.3 Polyester powder coated aluminium (minimum
thickness of polyester powder coating 50 micron) kg 55.13 385.10 21228.64
21.1.2 b For Openable portion
21.1.2.3 Polyester powder coated aluminium (minimum
thickness of polyester powder coating 50 micron) kg 165.38 443.20 73294.20
419053.04WATER PROOFING
Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
22.500 45 Providing and laying water proofing treatment in
sunken portion of WCs, bathroom etc., by applying
cement slurry mixed with water proofing cement
compound consisting of applying : a) First layer of
slurry of cement @ 0.488 kg/sqm mixed with water
proofing cement compound @ 0.253 kg/sqm. This
layer will be allowed to air cure for 4 hours. b)
Second layer of slurry of cement @ 0.242 kg/sqm
mixed with water proofing cement compound @
0.126 kg/sqm. This layer will be allowed to air cure
for 4 hours followed with water curing for 48 hours.
The rate includes preparation of surface, treatment
and sealing of all joints, corners, junctions of pipes
and masonry with polymer mixed slurry. sqm 114.68 283.10 32465.91
MR 46 (a)Plastering and repairing the surface .After
removing the kota stone and bedding mortar the
surface is to be plastered with KEM PROOF/Sika
Top 77/POWERCRETE or equivalent (Acrylic
emulsion and water proof addictive with having a
density 1.03 kg/ltr at 27deg C and solid content 40%)
modified cement moratr.It will be applied with
aproportion of 1:4 by volume of additive to water.
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
(b)Waterproofing Treatment :
Surface preparation: Cleaning all loose particles like
cement, sand, and substrate making than even surface
free from dust, dirt, grease using the steel/nylon wire
brush for cleaning.
Surface to be treated should be sound, clean and free
from dirt oil and other loose material. Washing the
surface with adequate water ensuring complete
cleaning.
Treatment :
Providing and applying two coats of elastomeric,
single component Polyurethane based, liquid applied
waterproof coating membrane system with fiber glass
mesh after application of priming material as per
manufacturer’s specification on the prepared
substrate. There should be minimum interval of 4-6
Hrs after between priming the surface and
waterproof PU based membrane coating. Interval
between two coats of PU based coating membrane
should be minimum 12 Hrs.
Immediately after the 2nd and final coat on the
surface spray of fine washed sand to be done @6
CUDM/Sqm
Details of PU based coating :
Standard Compliance : ASTM D412, E96-05, ASTM
G154, ASTM836-05, ASTM 836-84M, BS 476: Part
III, ISO 1523,1983 /ASTM 836-89, / ASTM 836-84,
(c) After the above coating laying of average 50mm
thick PCC over the coating and finishing smooth and
mixing of rich polymer of 40% @1kg per bag of
cement (Polymer solid contents as per ASTM
C1059),ensuring that screed gently slopes towards the sqm 641.42 1250.00 801779.34
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
9.510 51 Providing and fixing fly proof galvanized M.S. wire
gauge to windows and clerestory windows using wire
gauge with average width of aperture 1.4 mm in both
directions with wire of dia 0.63 mm all complete.
9.51.2 With 12 mm mild steel U beading sqm 295.25 578.30 170740.18
32465.91 972519.53Total
DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount
(1) (2) (3) (4) (5) (6) (7) (8)
BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR
CIVIL WORKS
MARKET RATE ITEMS
M.R 52 Providing and laying light cinder filling under floors
of toilets and kitchen and other sunken roofs rammed
and compacted complete. cum 36.54 579.00 21156.66
M.R 53 Providing & laying, polished 18mm to 20mm thick
Granite flooring with water absoption,s less than
0.08% and conforming to IS : 15622 of approved
make in all colours and shade , laid on 20 mm thick
cement mortar 1:4 ( 1 cement : 4 coarse sand )
including grouting the joint with white cement and sqm 500.17 4270.00 2135706.90
#########TOTAL COST OF CIVIL
TOTAL
S.No SUB HEAD DISCRIPTIOND.S.R. ITEM N.S. ITEM
I POINT WIRING (Copper Wiring in Pvc
Conduits)
1117263.00 0.00
II ERECTION OF LIGHTING FIXTURES
AND FANS
116218.00 9690.00
III TELEPHONE, TELEVISION AND
DATA NETWORK16084.00 0.00
IV SUPPLY OF LIGHTING FIXTURES AND
FANS
0.00 1017357.91
V DISTRIBUTION BOARDS, MCB'S AND
POWER DISTRIBUTION SYSTEM
64972.00 955100.93
VI External Lighting 102336.00 644643.00VII CABLE AND ITS LAYING 233358.00 857650.00VIII EARTHING 151706.00 0.00IX LIGHTNING CONDUCTORS 81701.00 0.00X MISCELLANEOUS 266.00 99459.00
SUB TOTAL 1883904.00 3583900.84
TOTAL 5,467,804.84
PROJECT NAME : NIT Hostel AtRaipur
NAME OF WORK: Internal Wiring, Distribution Board/ MCB, Supply of Lighting SUMMARY OF COST
AMOUNT (Rs.)
S. No. CODE DESCRIPTION QTY. UNIT RATE
D.S.R. ITEM N.S. ITEM
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)1.1 1.10 Wiring for light point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable in surface / recessed
medium class pvc conduit, with modular switch, modular
plate, suitable GI box and earthing the point with 1.5 sq.mm.
FRLS PVC insulated copper conductor single core cable etc 1.1.a 1.10.3 Group C 287 Point 718.00 206066.00
1.2 1.10 Wiring for fan point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable in surface / recessed
medium class pvc conduit, with modular switch, modular
plate, suitable GI box and earthing the point with 1.5 sq.mm.
FRLS PVC insulated copper conductor single core cable etc 1.2.a 1.10.3 Group C 123 Point 718.00 88314.00
1.3 1.10 Wiring for exhaust fan point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface /
recessed medium class pvc conduit, with modular switch,
modular plate, suitable GI box and earthing the point with 1.5
sq.mm. FRLS PVC insulated copper conductor single core 1.3.a 1.10.3 Group C 25 Point 718.00 17950.00
1.4 1.10 Wiring for call bell point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface /
recessed medium class pvc conduit, with modular switch,
modular plate, suitable GI box and earthing the point with 1.5
sq.mm. FRLS PVC insulated copper conductor single core 1,4,a 1.10.3 Group C 0 Point 718.00 0.00
1.5 1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface /
recessed PVC conduit, 2 way modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm. FRLS
PVC insulated copper conductor single core cable etc as
24 Point 770.00 18480.00
1.6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with
the following sizes of FRLS PVC insulated copper conductor,
single core cable in surface/ recessed medium class PVC
conduit as required1.6.a 1.14.1 2X1.5 Sqmm+1X1.5 sqmm earth wire 200 Meter 106.00 21200
1.6.b 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2355 Metre 131.00 308505.00
1.6.c 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 240 Metre 162.00 38880.00
1.6.d 1.14.10 4 X 10 sq. mm + 2 X 10 sq. mm earth wire 250 Metre 597.00 149250.00
1.6.e 1.14.11 4 X 16 sq. mm + 2 X 16 sq. mm earth wire 240 Metre 883.00 211920.00
1.6.f 1.14.4 2X6 6Sqmm+1X6 Sqmm earth Wire 240 Meter 221.00 53040.00
ESTIMATE FOR NIT HOSTEL Raipur(C.G)
AMOUNT (RS.)
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)1.6.g NA Additional payment Usind Recommended Company FRLS ISI
Single Core Multi Stranded wire in place of ISI wire in
CPWD Point & Circuit Wiring Items
As Per Site Meter 10% of Related
Items Rate
TOTAL SUB HEAD (I) 1,113,605.00
SUB HEAD (II):- ERECTION OF LIGHTING
FIXTURES AND FANS2.1 1.41 Installation, testing and commissioning of pre-wired,
fluorescent fitting / compact fluorescent fitting of all types,
complete with all accessories and tube etc. directly on ceiling/
wall, including connection with 1.5 sq. mm FRLS PVC
insulated, copper conductor, single core cable and earthing
149 Each 91.00 13559.00
2.2 1.45 Installation, testing and commissioning of ceiling fan,
including wiring the down rods of standard length (upto 30
cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor,
single core cable, including providing and fixing phenolic
laminated sheet cover on the fan box etc. as required.
123 Each 122.00 15006.00
2.3 1.46 Installation, testing and commissioning of resistance type
ceiling fan regulator, in existing switch box including
connection with 1.5 sq. mm FRLS PVC insulated, copper
conductor, single core cable, earthing the regulator etc. as
123 Each 52.00 6396.00
2.4 The fixing and testing of lighting fixture shall include
connection with 3 x 1.5 sqmm flexible fire retardant copper
connecting wire of required length complete with all
accessories, control gears, transformer, including screws, nuts,
wooden cleats, making hole in wall or ceiling and making 2.4.a NA Down lighter luminaire of all types with all accessories
directly on recess
126 Each 75.00 9450
2.4.b NA Mirror type light fittings of all types with all accessories
directly on recess
12 Each 20.00 240
NA Wall Bracket CFL 0 Each 20.00 0
2.5 1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing
junction box/ wooden block including connection etc as
required.
123 Each 43.00 5289.00
2.6 1.50 Installation of exhaust fan in the existing opening, including
making good the damage, connection, testing, commissioning
etc. as required.2.6.a 1.50.1 Upto 450 mm sweep 25 Each 204.00 5100.00
2.7 1.51 Extra for fixing the louvers/ shutters complete with frame for
a exhaust fan of all sizes.
25 Each 90.00 2250.00
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)2.8 1.31 Supplying and fixing suitable size GI box with modular plate
and cover in front on surface or in recess, including providing
and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps
modular switch, connection etc. as required. (For light plugs
to be used in non residential buildings).
181 Each 303.00 54843.00
2.9 1.32 Supplying and fixing suitable size GI box with modular plate
and cover in front on surface or in recess, including providing
and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and
15/16 amps modular switch, connection etc. as required.
12 Each 395.00 4740.00
2.1 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type,
socket outlet, with 2 pole and earth, metal enclosed plug top
alongwith 20 amps "C" curve, SP, MCB, in sheet steel
enclosure, on surface or in recess, with chained metal cover
for the socket out let and complete with connections, testing
and commissioning etc. as required.
12 Each 954.00 11448.00
TOTAL SUB HEAD (II) 118631.00 9690.00
SUB HEAD (III):- TELEPHONE, TELEVISION AND
DATA NETWORK3.1 1.21 Supplying and fixing of following sizes of PVC conduit along
with the accessories in surface / recess including cutting the
wall and making good the same in case of recessed conduit as
required: (For Telephone / T.V. Cable/Data Network). 3.1.a 1.21.1 20mm 100 Meter 53 5300
3.1.b 1.21.2 25mm 100 Meter 65 6500
3.2 1.24 Supplying and fixing following modular switch/ socket on the
existing modular plate & switch box including connections
but excluding modular plate etc. as required.3.2.a 1.24.6 Telephone socket outlet 0 Each 95.00 0.00
3.2.b 1.24.7 TV antenna socket outlet 3 Each 94.00 282.00
3.3 1.27 Supplying and fixing following size/ modules, GI box
alongwith modular base & cover plate for modular switches in
recess etc as required.3.3.a 1.27.1 1 or 2 Module (75mmX75mm) 3 Each 166.00 498.00
3.4 1.18 Supplying & drawing telephone wire following pair, 0.5 sq
mm FRLS PVC insulated annealed copper conductor,
unarmoured telephone cable in the existing surface / recessed
PVC conduit as required.3.4.a 1.18.2 2 Pair 0 Meter 18 0.00
3.4.b N.A 10 Pair 0 Meter 68.00 0
3.5 1.19 Supplying & drawing co-axial TV cable RG-6 grade, 0.7 mm
solid copper conductor PE insulated, shielded with fine tinned
copper braid and protected with PVC sheath in the existing
surface / recessed conduit as required.
75 Meter 28 2100.00
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)3.6 Providing, fixing, connecting & testing of Krone box
(Telephone Tag Block) in a thermoplastic, IP 65 (weather
proof) enclosure, internally embedded gasket, anti corrosive,
insulated and shock proof with provision for cable through IP
65 glands complete in all respects. 3.6.a N.A 10 pairkrone 0 Each 844.00 0
3.7 N.A Supply & installation of Cat 6 information outlet complying
fully or exceeding with category 6 connecting hardware
specification for all pair combination upto 250 MHz. Outlets
shall use lead frame technology, non PCB pyramid type. (Blue
in colour for data).
0 Each 330.00 0.00
3.8 N.A Supply & Installation of single port face plates along with
clearly printed lables and holders.
0 Each 192.00 0.00
3.9 Providing, drawing, connecting and testing of enhanced
category 4 pair LAN (local area network) cable, UL and CUL
listed, in existing MS/PVC conduit or floor raceways
including connections etc as required complete in all respects. 3.9.a N.A CAT- 6 network cable 0 Meter 78.00 0.00
3.11 1.38 Supplying and fixing call bell/ buzzer suitable for single
phase,230 volts, complete as required.
0 Each 61.00 0.00
TOTAL SUB HEAD (III) 14,680.00 0.00
SUB HEAD (IV):- SUPPLY OF LIGHTING FIXTURES
AND FANS(The sample of all lighting fixtures & fans should be approved
by Engineer In charge or Architect before procurement)4.1 Supply of Recess mounted 600 X600 mm Module 2
X36 watt Compact CFL type Mirror optic Fitting with
required CFL lamps, control gear box etc. complete in all
respect as required as per the standard catalogue item.
Make: philps or equivalent4.1.a N.A. FBS 300 2XPL-L36 W P EBT 44 Nos 6954.00 305,976.00
4.2 Supply of Wall mounted Deco Battons T-5 type Fitting with
T-5 lamps, control gear box etc. complete in all respect as
required as per the standard catalogue item. Make: Phillips or
equivalent(TCS019 1xTL-D 36W EBT)4.2.a N.A. 1 x 36W T-5 surface mounted 105 Nos 749.00 78,645.00
4.3 Supply of recess mounted CFL type ceiling light fixtures
down lighter with required nos. lamps etc. complete in all
respect as required as per the standard catalogue item.4,3,b N.A. 18W 126 Nos 1605.00 202,230.00
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)N.A. Supply of 14 Watt Wall Bracket CFL 0 Nos 227.00
4.4 Supply of wall mounted Mirror type light fixtures with
required nos. lamps etc. complete in all respect as required as
per the standard catalogue item.4.4.a N.A. 2x13W 12 Nos 1109.66 13,315.91
4.5 Supply of AC 230/250 volts, 50Hz ceiling fan with standard
down rod, blades, 2 nos caps etc. complete. Make: Havells or
equivalent4.5.a N.A. 1200 mm sweep 123 Nos 2942.00 361,866.00
4.6 Supply of AC 230/250 volts, 50Hz exhaust fans including
providing nuts, bolts, mounting frame and other accessories
etc. complete (Havells make or equivalent)4,6,a N.A. 250 mm sweep 25 Nos 2213.00 55,325.00
TOTAL SUB HEAD (IV) 0.00 1,017,357.91
SUB HEAD (V):- DISTRIBUTION BOARDS, MCB'S
AND POWER DISTRIBUTION SYSTEM
5.1 N.A Design, manufacture, supply, installation, testing and
commissioning of main distribution board fabricated out of 14
SWG sheet steel, wall / floor mounting type, with seven tank
treatment process followed by powder coat painting having a
paint thickness of 60 microns., 415 V electrolitic Al. Bus bar
having short circuit current is 50kA and, removable gland
plates as per SLD . including connection with outgoing
feeders complete in all respect. panels will be provided with
suitable gasket to make it dust/vermin proof. IP 54 protectionThe above board shall be complete with 3 nos. phase
indicating lights, flush mounted Ammeter, Voltmeter, CT's,
PT's selector switches, protective fuses etc. at Incomer with all
inter connetions by min. 2.5 sq mm Copper wires.Main panel 1 SET 504791.90 504791.90
INCOMER:
400 Amp FP MCCB 36 KA
250 Amp FP MCCB 36 KA
BUS BAR: 600 AMP TPN AL.
Automatic Change Over : 600 A Manual Change Over
OUTGOINGS:
100A FP MCCB 36kA 4 nos
63A FP MCCB 36kA 1 nos
63A TP MCB 36kA 2 nos
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)40A TP MCB 36kA 4nos
5.3 N.A Supply, installation, testing and commissioning of weather
and vermin proof outdoor type External Lighting feeder pillar
(IP-65) fabricated from 14 SWG thick CRCA sheet steel
construction suitable for 3 phase, 4 wire, 415 volt, 50 Hz A.C.
distribution complete with Al. bus bars, switch fuse unit,
timer, contactor, fitting with fuse link, locking arrangement
complete as per specification required.INCOMER:-
1 No. 100 Amp. TPN MCCB with neutral link.
1 set of time switch contactor push button changeover switch
etc. complete as per drawing suitable for automatic operation
of external lighting.BUS BAR : 200AMP TPN Al.
OUTGOING :-
1 No. 63 Amp. TPN MCB with neutral link.
5 No. 32 Amp. TPN MCB with neutral link.
20 mm x 3mm GI earth busbar to be fixed inside the pillar and
for connection outside earth strip on both sides of pillar
1 Set 109080 109080
5.4 NA Supply Installation Testing & Commissioning of Out door
Type weather and insect proof pole mounted distribution
junction box Made out of 14 SWG CRCA Sheet steel
construction with approved Colour paintrd having following
incomer and out going
1 Nos Incomer MCB Isolator 32 Amp
1 Nos Outgoing Singal pole MCB 10 Amp
Internaly cnnected with 16 Sqmm Flexible PVC Insulatrd FR
Copper conductor.
30 SEt 8211 246340
5.4 2.5 Supplying and fixing of following ways surface/ recess
mounting, vertical type, 415 volts, TPN MCB distribution
board of sheet steel, dust protected, duly powder painted,
inclusive of 200 amps tinned copper bus bar, common neutral
link, earth bar, din bar for mounting MCB's (but without
MCB's and incomer ) as required . (Note : Vertical type MCB
TPDB is normally used where 3 phase outlets are required.)5,4,a 2.5.4 4 way (4 + 12), Double door 2 Each 4478 8956.00
2.5.5 8 Way(4+24) Double Door 1 5641 5641.00
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)5.5 2.4 Supplying and fixing following way, horizontal type three
pole and neutral, sheet steel, MCB distribution board, 415
volts, on surface/ recess, complete with tinned copper bus bar,
neutral busbar, earth bar, din bar, interconnections, powder
painted including earthing etc. as required. (But without
MCB/ RCCB/5,5,b 2.4.5 6 way (4 + 18), Double door 1 Each 2636 2636.00
5,5,c 2,4,4 4 way (4 + 12), Double door 2 Each 2175 4350.00
2.4.6 8 Way(4+24) Double Door 9 Each 3148 28332
5.6 N.A Supplying and fixing following rating, four pole, 415 volts,
MCCB in the existing MCB DB complete with connections,
testing and commissioning etc. as required.5,6,a N.A 100 amps FP MCCB 3 Each 11189.00 33567.00
5,6,c N.A 63 amp FP MCB 24 Each 2190.07 52561.77
5,6,d N.A 40 amp FP MCB 4 Each 2190.07 8760.30
5.7 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,
"C" curve, miniature circuit breaker suitable for inductive load
of following poles in the existing MCB DB complete with
connections, testing and commissioning etc. as required.5,7,a 2.10.1 Single pole 136 Each 169 22984.00
5.8 2.11 Supplying and fixing single pole blanking plate in the existing
MCB DB complete etc. as required.
25 Each 7 175.00
TOTAL SUB HEAD (V) 73074.00 955100.93
SUB HEAD (VI):- EXTERNAL LIGHTING
6.1 N.A Supply of pole mounted Street Light for external lighting
suitable for CDMT lamps complete with required nos. lamps
and control gear etc. complete as required as per the standard
catalogue item.6.1.a N.A BGWRL 150 SV FFG (MH T 150W) 7 Each 9528.00 66696
6.2 N.A Supply of pole mounted post top lantern for external lighting
suitable for CDMT lamps complete with required nos. lamps
and control gear etc. complete as required as per the standard
catalogue item.6,2,a N.A SPC101 1xSON70W E 19 Each 6161.00 117059
6.3 N.A Supply of bollard garden light suitable for CFL lamps
complete with required nos. lamps, control gear etc. complete
as required as per the standard catalogue item.6,3,a N.A HCS 360 1xPLC/2P18W GR 20 Each 7241.00 144820
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)6.4 N.A Installation, testing and commissioning of Street Light with
required lamps complete with control gear box, ballast,
capacitor etc. including connection with 3 x 1.5 sq.mm
flexible fire retardant copper connecting wire of required
7 Each 400 2800
6.5 N.A Installation, testing and commissioning of CDMT type post
top lantern with required lamps complete with control gear
box, ballast, capacitor etc. including connection with 3 x 1.5
sq.mm flexible fire retardant copper connecting wire of
required length complete as required.
19 Each 400 7600
6.6 N.A Installation, testing and commissioning of CFL type bollard
garden light fixtures with required lamps, control gear box,
including connection with 3 x 1.5 sq.mm flexible fire
retardant copper connecting wire of required length complete
20 Each 300 6000
6.7 N.A Supply and fixing of steel tubular pole 7.50 m long of
designation 410 SP-6 fixed in 1:3:6 cement concrete
foundation, including excavation, back filling etc. complete in
7 Each 6000.00 42000
6.8 NA Supply and fixing of GI Octagonal GI 11 Mtr hight Pole
Complete with all acessories like base plate foundation
acessories top canopy for high mast light mounting etc.fixed
in 1:3:6 cement concrete foundation, including excavation,
back filling etc. complete in all respects.
2 Each 21900.00 43800
6.9 N.A Supply and fixing of steel tubular pole 4.50 m long of
designation 410 SP-6 fixed in 1:3:6 cement concrete
foundation, including excavation, back filling etc. complete in
19 Each 5764.00 109516
7 11.4 Erection of steel tubular or rail pole strut in cement concrete
1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40
mm nominal size ) foundation including excavation and
refilling and secured with holding clamps, bolts, nuts, etc. as
26 Each 4318 112268.00
7.10 Supply of Façade Lighting Luminaries integral flood light(
Fitting+Controll gear+Bulb) single piece pressure die cast
aluminiam housing toughned glass cover (IP65 ) ingress
protection and rectangular reflacter for planer symetic optical
distribution.
8 Each 10544.00 84352
SWF33I IXSONT250W S
7.11 Installation and commissioning of Flood Light Luminaries
with all acessories in suitale high angle frame stand Complete
in All Respect etc.
8 Each 1000 8000
7.12 Supply And Fixing of angle frame stand made 25 X 5 mm
angle for flood Light
4 Each 3000 12000
TOTAL SUB HEAD (VI) 112268.00 644643.00
SUB HEAD (VII):- Cable and its Laying
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)7.1 N.A. Supply of ISI marked XLPE insulated cable as per IS 7098,
armoured, served, sheathed 1100 volts grade,Make:- (Havells
or Equivalent)7.1.a N.A. 3.5CX400 Sqmm Al XLPE insulated Armoured Cable 150 Metre 2577.00 386,550.00
7.1.c N.A. 3.5CX150 Sqmm Al XLPE insulated Armoured Cable 150 Metre 1075.00 161,250.00
7.1.d N.A. 3.5CX70 Sqmm Al XLPE insulated Armoured Cable 300 Metre 585.00 175,500.00
7.1.e N.A. 3.5CX35 Sqmm Al XLPE insulated Armoured Cable 50 Metre 323.00 16,150.00
7,1,h N.A. 4CX16 Sqmm AL XLPE insulated Armoured Cable 500 Metre 218.00 109,000.00
7,1,g N.A. 3CX16 Sqmm AL XLPE insulated Armoured Cable 50 Metre 184.00 9,200.00
7.2 7.1 Laying of one number PVC insulated and PVC sheathed /
XLPE power cable of 1.1 KV grade of following size direct in
ground including excavation, sand cushioning, protective
covering and refilling the trench etc as required.7.2.a 7.1.1 Upto 35 sq. mm 600 Metre 195.00 117000.00
7.2.b 7.1.2 Above 35 sq. mm and upto 95 sq. mm 300 Metre 202.00 60600.00
7.2.c 7.1.3 Above 95 sq. mm and upto 185 sq. mm 150 Metre 210.00 31500.00
7.2.d 7.1.4 Above 185 sq. mm and upto 400 sq. mm 150 Metre 233.00 34950.00
7.3 9.1 Supplying and making indoor end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.7.3.a 9.1.31 3½ X 400 sq. mm (82mm) 2 Each 1369.00 2738.00
7.3.c 9.1.26 3½ X 150 sq. mm (50mm) 2 Each 576.00 1152.00
7.3.d 9.1.23 3½ X 70 sq. mm (38mm) 4 Each 382.00 1528.00
7.3.e 9.1.21 3½ X 35 sq. mm (32mm) 2 Each 270.00 540.00
7,3,f 9.1.33 4 X 16 sq. mm (28mm) 8 Each 245.00 1960.00
TOTAL SUB HEAD (VII) 251,968.00 857,650.00
SUB HEAD (VIII):- EARTHING
8.1 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm
thick including accessories, and providing masonry enclosure
with cover plate having locking arrangement and watering
pipe of 2.7 metre long etc. with charcoal/ coke and salt as
2 Set 9292.00 18,584.00
8.2 5,4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm
thick including accessories, and providing masonry enclosure
with cover plate having locking arrangement and watering
pipe of 2.7 metre long etc. with charcoal/ coke and salt as
10 Set 4490.00 44,900.00
8.3 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm
dia G.I. pipe from earth electrode including connection with
brass nut, bolt, spring, washer excavation and re-filling etc. as
20 Metre 1082.00 21,640.00
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)8.4 5,11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia
G.I. pipe from earth electrode including connection with G.I.
nut, bolt, spring, washer excavation and re-filling etc. as
100 Metre 421.00 42,100.00
8.5 5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia
including
accessories, and providing masonry enclosure with cover plate
having locking arrangement and watering pipe etc. with
6 Nos 3926.00 23,556.00
8.6 5.12 Providing and laying earth connection from earth electrode
with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth
electrode
including connection with G.I. thimble excavation and
60 Meter 151.00 9,060.00
TOTAL SUB HEAD (VIII) 159,840.00 0.00
SUB HEAD (IX) : LIGHTNING CONDUCTORS
9.1 6.1 Providing and fixing of lightning conductor finial, made of 25
mm dia 300 mm long, copper tube, having single prong at top,
with 85 mm dia 3 mm thick copper base plate including holes
etc. complete as required.
1 Each 764.00 764.00
9.2 6.4 Jointing copper / G.I. tape (with another copper/ G I tape, base
of the finial or any other metallic object) by riveting / nut
bolting/ sweating and soldering etc as required.
10 Each 72.00 720.00
9.3 6.5 Providing and fixing copper tape 20 mm X 3 mm thick on
parapet or surface of wall for lightning conductor complete as
required.(For horizontal run)
150 Metre 376.00 56,400.00
9.4 6.6 Providing and fixing copper tape 20 mm X 3 mm thick on
parapet or surface of wall for lightning conductor complete as
required.(For vertical run)
70 Metre 406.00 28,420.00
TOTAL SUB HEAD (IX) 86,304.00 0.00
SUB HEAD (X):- MISCELLANEOUS
10.1 2.21 Providing and fixing M.V. danger notice plate of 200 mm X
150mm, made of mild steel, at least 2 mm thick, and vitreous
enameled white on both sides, and with inscription in single
red colour on front side as required.
2 Each 141 282
10.2 N.A Supply and fixing of shock treatment chart (prescribed under
I.E. rules) duly framed with glass and supported from back
with hard board with supply of all material labour T & P etc
for proper completion of work.
1 Each 1458.00 1458
10.3 N.A Supply, fixing, testing, commissioning of 1800mm x 900mm
x 20mm thick chequered rubber matting of tested quality to
with stand 11 KV dielectric strength complete in all respects.
1 Each 5787.00 5787
10.4 N.A Supply of 11 KV grade rubber hand gloves in pair as per IS 2 Each 1104.00 2208
SUB HEAD (I):- POINT WIRING (Copper Wiring in
PVC Conduits)10.5 N.A Supply and fixing of fan box with hexagonal side of approx.
80mm in length fabricated from 18 SWG MS sheet
incorporating with 10 mm dia MS round bar duly bent for
supportiong fan hanger painted with red oxide and screwing
arrangement with wiring conduit laid in the RCC roof before
concreting along with supply of all materials, labour, T&P etc.
123 Each 122.00 15006
10.6 NA Dismantling of Electrical Existing Lighting Equipment Like
Fitting, Conduit Pipe, Wire,SDB, Switch Board, Fan, Exhaust,
Panel etc And All material hand over to department in their
relative store
1 Job 75000.00 75000
Total Of Sub Head (X) 282 99459
11 NA Supplying of following KVA compact packaged silent type
D.G Set (With acoustic enclosure to reduce the noise level as
per requirements of central pollution control board) 415Volts,
3 phase, 50 Hz AC alternator coupled to diesel engine
complete with all accessories, standard specifications tool
kits, service manual, self starting device, fly wheel, coupling
with guard, V velt, radiator, instrument panel (starting switch
with key, Water Temperature indicator gauge, Lub OIl
Pressure gauge, Lube oil temperature gauge, Battery Charging
AmMetre, indicating lamp, hour counter etc.), residential type
silencer, common bed plate, anti vibration isolation pads,
grouting bolts, first charge of engine oil, gear oil, high speed
diesel oil, 24 volt / 12 volt chargeable battery set with Trickle
/ Boost Battery charger complete as required including
erecting, testing and commissioning of following type 415
Volts, 3 phase, 50 Hz. AC alternator coupled to Diesel Engine 125 KVA D.G. Set (with fuel tank for 6 hrs full load
operation outside the Canopy)
0 Nos 596000.00 0
TOTAL SUB HEAD (XI) 0 0
DSR 2014 NON-DSR
ISANITARY
INSTALLATIONS & C.P.
FITTINGS
185608.80 75800.00
IISOIL WASTE & VENT
PIPES AND FITTINGS554386.65 28800.00
IIIINTERNAL & EXTERNAL
WATER SUPPLY WORKS313065.20
IV SEWERAGE SYSTEM 98464.10
V EXTERNAL PLUMBING 1279305.00
TOTAL 2430829.75 104600.00
GRAND TOTAL
SAY
2535429.75
2535430.00
SCHEDULE OF QUANTITIES FOR PLUMBING WORKS
PROPOSED RENOVATION WORK OF HOSTEL BLOCK E
FOR N.I.T., RAIPUR (CHATTISGARH)
SUMMARY OF COST INTERNAL PLUMBING WORKS
S.NO NAME OF SUB-HEADAMOUNT
SL.
NO
DSR
2014DESCRIPTION UNIT QTY
RATE
(in Rs)
AMOUNT
(in Rs)
ISanitary Instatllations
1 17.1 Providing and fixing water closet squatting pan ( Indian type
W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low
level white P.V.C. flushing cistern with manually controlled
device (handle lever) conforming to IS:7231,
Parryware/Hindware/Seabird/Orient (Coral) with all fittings and
fixtures complete including cutting and making good the walls
and floors wherever required.17.1.
1
White Vitreous china Orissa pattern W.C. pan of size
580x440mm with integral type foot rests each 6.00 3392.80 20356.80
2 17.2 Providing and fixing white vitreous china pedestal type water
closet (European type W.C. pan) with seat and lid, 10 litre low
level white P.V.C. flushing cistern with manually controlled
device (handle lever), conforming to IS : 7231,
Parryware/Hindware/Seabrid /Orient (Coral) with all fittings
and fixtures complete including cutting and making good the
walls and floors wherever required : 17.2. W.C. pan with ISI marked black solid plastic seat and lid each 12.00 3293.05 39516.60
3 17.7.
4
Providing & fixing white vitreous china wash basin with C.I.
brackets painted white, 15 mm C.P. brass pillar taps, C.P.
brass chain with rubber plug, 32mm C.P. brass waste of
standerd pattern including cutting & making good the walls
wherever required. a)White Vitreous China Flat back wash Basin size 550x400 mm
with single 15 mm C.P. brass pillar tap. each 18.00 1807.10 32527.80
4 17.3 Providing and fixing P.V.C. waste pipe for sink or wash basin
including P.V.C. waste fittings complete.17.28
.1
Semi rigid pipe
17.28
.1.1
32 mm dia each 18.00 76.75 1381.50
17.28
.1.2
40 mm dia each 1.00 82.60 82.60
SCHEDULE OF QUANTITIES FOR PLUMBING WORKS PROPOSED RENOVATION WORK OF HOSTEL BLOCK E FOR N.I.T., RAIPUR (CHATTISGARH)
INTERNAL PLUMBING WORKS
SANITARY INSTALLATIONS & C.P FITTINGS
5 17.3 Providing and fixing 600x450mm bevelled edge mirror of
superior glass (of approved quality) complete with 6mm thick
hard board ground fixed to wooden cleats with C.P. brass
screws and washers complete. each 18.00 793.95 14291.10
6 17.10 Providing and fixing Stainless Steel AISI 304 (18/8) kitchen
sink as per I.S. 13983 with C.I. brackets and stainless steel
plug 40 mm including painting of fittings and brackets, cutting
and making good the walls wherever required :17.10
.1
Kitchen sink with drain board
17.10
.1.1
510x1040mm bowl depth 250mm each 1.00 7052.15 7052.15
CP Brass fittings7 18.2 Providing and fixing unplasticised PVC connection pipe with
brass unions18.21
.2
45 cm length
18.21
.2.1
15 mm nominal bore each 55.00 68.60 3773.00
8 18.5 Providing and fixing C.P. brass bib cock of approved quality
conforming to IS:893118.49
.1
a) 15 mm nominal boreeach 18.00 459.50 8271.00
9 18.5 Providing and fixing C.P. brass long body bib cock of approved
quality conforming to IS standards and weighing not less than
690 gms.18.51
.1
a) 15 mm nominal boreeach 39.00 610.65 23815.35
10 18.5 Providing and fixing C.P. brass angle valve for basin mixer and
gyser points of approved quality conforming to IS:893118.53
.1
a) 15 mm nominal boreeach 43.00 507.70 21831.10
11 18.2 Providing and fixing C.P. brass shower rose with 15 or 20mm 18.22
.2
150 mm diameter each 18.00 86.35 1554.30
12 Providing and fixing C.P. brass stop cock (concealed) of
standard design and of approved make conforming to IS:8931:18.52.115mm nominal bore each 18.00 619.75 11155.50
TOTAL [I] 185608.80
II
1 Providing & fixing soil, waste and vent pipes.17.35.1.2a) 100mm dia centrifugally cast iron S & S pipe. Rm. 100.00 917.75 91775.00
17.35.2.2b) 75mm dia centrifugally cast iron S & S pipe. Rm. 200.00 791.30 158260.00
2 Providing lead caulked joints to sand cast iron/centrifugally cast
(spun) iron pipes & fitting of diameters.17.58.1a) 100mm No. 71.00 243.75 17306.25
17.58.2b) 75mm No. 142.00 205.30 29152.60
3 Providing & fixing M.S. holder bat clamps of approved design to
sand cast iron/centrifugally cast (Spun) iron S & S pipe
embeded in & including cement concrete blocks 10x10x10cm.
of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate size). Including cost of cutting holes & making good the walls
etc.17.37.1a) for 100mm dia pipe. No. 28 152.90 4281.20
17.37.2b) for 75mm dia pipe. No. 56 150.60 8433.60
4 Providing & fixing cast iron trap of self cleansing design with or
without ventarm complete, including cost of cutting & making
good the walls & floors.17.60.2.1a) 100mm inlet & 75mm outlet. No. 50.00 1020.90 51045.00
5 Providing & fixing cast iron coller.17.57.1.2a) 100mm dia. No. 50.00 318.35 15917.50
17.57.2.2b) 75mm dia. No. 100.00 219.75 21975.00
6 Providing and fixing plain cast iron S & S sanitary bend.17.39.1.2a) 100mm Nos. 22.00 335.75 7386.50
17.39.2.2b) 75mm Nos. 9.00 248.80 2239.20
7 Providing and fixing bend of required degree with access door,
insertion rubber washer 3mm thick, bolts and nuts complete.17.38.1.2a) 100mm Each 0.00 385.70 0.0017.38.2.2b) 75mm Nos. 1.00 318.50 318.50
8 Providing and fixing centrifugaly cast iron single equal plain
junction of required degree. 17.44
.1.2
100x100x100mm Nos. 18 576.20 10371.60
SOIL WASTE & VENT PIPES AND FITTINGS
17.44
.2.2
75x75x75mm Nos. 24 405.60 9734.40
9 Providing and fixing cast iron terminal guard. 17.56
.1.2
100 mm Nos. 4 434.50 1738.00
17.56
.2.2
75 mm Nos. 8 370.75 2966.00
10 DSR
no.19
.2.1
Providing and laying cement concrete 1:5:10(1 cement : 5
coarse sand : 10 graded stone aggregate 20mm nominal size)
around P.V.C Soil and waste pipe including bed concrete as per
standard design(embedded in the flooring / ground)100 mm dia metre 50.00 592.60 29630.00
75 mm dia metre 100.00 340.00 34000.00
11 12.41 Providing and fixing on wall face unplasticised-Rigid PVC rain
water pipes conforming to IS: 13592 Type A including jointing
with seal ring conforming to IS: 5382 leaving 10mm gap for
thermal expansion. 12.41
.2
110 mm Metre150.00
231.6534747.50
12 12.42 Providing and fixing on wall face unplasticised PVC moulded
fittings/accessories for unplasticised Rigid PVC rain water pipes
conforming to IS:13592 Type A including jointing with seal
ring conforming to IS:5382 leaving 10mm gap for thermal 12.42
.5.2
Bend 87.5 degree
12.42
.5.2
110 mm Bend Each13.00
161.552100.15
12.42
.6
Shoe (Plain)
12.42
.6.2
110 mm Shoe Each13.00
295.103836.30
13 12.43 Providing and fixing unplasticised-PVC pipe clips of approved
design to unplasticised-PVC rain water pipes by means of
50x50x50 mm hard wood plugs, screwed with MS screws of
required length including cutting brick work and fixing in
cement mortar 1:4 (1 cement : 4 coarse sand) and making
good the wall etc. complete. 12.43
.2
110 mm Each78.00
189.0514745.90
14 12.22 Making khurras 45x45 cm with average minimum thickness of
5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate of 20 mm nominal size) over PVC
sheet 1m x 1 m x 400 micron, finished with 12 mm cement
plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat
cement,punning,rounding the edges and making and finishing Each 13.00 186.65 2426.45
TOTAL [II] 554386.65
III
1 Providing and fixing GI pipes complete with GI fittings
and clamps, including cutting and making good walls etc.
(internal work).Internal work-Exposed on wall
18.10.115mm dia nominal bore Metre 135 215.10 29038.50
18.10.220mm dia nominal bore Metre 40 249.30 9972.00
18.10.325mm dia nominal bore Metre 75 304.15 22811.25
18.10.432mm dia nominal bore Metre 50 343.20 17160.00
18.10.540mm dia nominal bore Metre 25 425.65 10641.25
18.10.650mm dia nominal bore Metre 60 527.20 31632.00
18.12.765mm dia nominal bore Metre 0 515.55 0.00
2 Painting GI pipes and fittings with SYNTHETIC enamel paint
over a ready mixed priming coat, both of approved quality for
new work.18.38.115mm dia nominal bore Metre 135 9.60 1296.00
18.38.220mm dia nominal bore Metre 40 11.35 454.00
18.38.325mm dia nominal bore Metre 75 14.95 1121.25
18.38.432mm dia nominal bore Metre 50 17.70 885.00
18.38.540mm dia nominal bore Metre 25 21.00 525.00
18.38.650mm dia nominal bore Metre 60 24.75 1485.00
18.40.765mm dia nominal bore Metre 0 15.60 0.00
3 Providing and fixing GI Union in GI pipes including cutting and
threading the pipe and making long screws etc. complete (new
work).18.46.115mm dia nominal bore Metre 45 165.25 7436.25
18.46.220mm dia nominal bore Metre 13 188.50 2450.50
18.46.325mm dia nominal bore Metre 25 200.00 5000.00
18.46.432mm dia nominal bore Metre 17 240.75 4092.75
18.46.540mm dia nominal bore Metre 8 316.25 2530.00
18.46.650mm dia nominal bore Metre 20 392.40 7848.00
18.46.765mm dia nominal bore Metre 0 623.25 0.00
INTERNAL & EXTERNAL WATER SUPPLY WORKS
418.17
Providing and fixing gun metal gate valve with wheel of
approved quality.18.17.1a) 25mm dia nominal bore Each 7.00 428.85 3001.9518.17.2b) 32mm dia nominal bore Each 6.00 501.50 3009.0017.17.3c) 40mm dia nominal bore Each 2.00 585.50 1171.0018.17.4d) 50mm dia nominal bore Each 6.00 750.75 4504.5018.17.5e) 65mm dia nominal bore Each 0.00 1286.25 0.00
5 18.48 Providing and placing on terrace (at all floor levels)polyethylene
water storage tank ISI : 12701 marked indicating the BIS
License No. with cover and suitable locking arrangement and
making necessary holes for inlet, outlet and over flow pipes but
without fitting and base support for tank.[Sintex, Electroplast,
Star, Lotus or equivalent having valid ISI license].Capcity in Liters Per Ltrs 20000.00 7.25 145000.00
6 18.16 Providing and fixing brass stop cock of approved quality.18.16.2a) 20 mm nominal bore Nos. 0.00 344.85 0.00
TOTAL[III] 313065.20
IV
1 2.10 Excavating trenches of required width for pipes, cables etc.
including excavation for sockets and dressing of sides,
ramming of bottoms, depth upto 1.5m including getting out the
excavated soil, and then returning the soil as required, in
layers not exceeding 20cm in depth including consolidating
each deposited layer by ramming, watering etc. and disposing
of surplus excavated soil as directed, within a lead of 50m.2.10.1 All kinds of soil2.10.1.2Pipes, cables etc. exceeding 80mm dia but not exceeding metre 50.00 208.30 10415.00
2 19.1 Providing, laying and jointing glazed stoneware pipes grade 'A'
with stiff mixture of cement mortar in the proportion of 1:1 (1
cement : 1 fine sand) including testing of joints etc. complete.19.1.1 100mm diameter metre 5.00 206.55 1032.75
19.1.2 150mm diameter metre 45.00 314.35 14145.75
3 19.2 Providing and laying cement concrete 1:5:10 (1 cement: 5
coarse sand : 10 graded stone aggregate 40mm nominal size)
all round S.W. pipes including bed concrete as per standard 19.2.1 100mm dia SW pipe metre 5.00 592.60 2963.00
19.2.2 150mm dia SW pipe metre 45.00 724.70 32611.50
SEWERAGE SYSTEM
4 19.4 Providing and fixing square-mouth S.W. gully trap grade‘A’
complete with C.I. grating, brick masonry chamber with water
tight C.I. cover with frame of 300 x300 mm size (inside) the
weight of cover to be not less than 4.50 kg and frame to be not
less than 2.70 kg as per standard design19.4. 150 x 100 mm size P type19.4.
2.2
With Sewer bricks conforming to IS : 4885each 1.00 1664.80 1664.80
7 19.7 Constructing brick masonry manhole in cement mortar 1:4 (1
cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement
:2 coarse sand :4 graded stone aggregate 20mm nominal
size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand
:8 graded stone aggregate 40mm nominal size) inside
plastering 12mm thick with cement mortar 1:3 (1 cement :3
coarse sand) finished with floating coat fo neat cement and
making channels in cement concrete 1:2:4 (1 cement :2 coarse
sand :4 graded stone aggregate 20mm nminal size) finished
8 19.7.1 Inside size 90x80cms and 45cms deep including CI cover with
frame (light duty) 455x610mm internal diamensions total
weight of cover and frame to be not less than 38 kg (weight of
cover 23 kg and weight of frame 15kg).19.7.1.1With FPS bricks of class designation 75
(i) For Sewer Line each 3.00 8507.00 25521.00
9 Extra for depth for manholes: 19.8.1.1Size 90x80cm with FPS bricks (class I ). metre 1.50 5638.20 8457.30
10 19.2 Providing M.S. foot rests including fixing in manholes with
20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3
coarse sand :6graded stone aggregate 20 mm nominal size) as
per standard design19.15.1With 20x20 mm square bar each 6.00 275.50 1653.00
TOTAL[IV] 98464.10
V
1 NSR Extra for providing & fixing 125 mm dia C.P. grating in place
of C.I. grating over floor traps. Each 50.00 80.00 4,000.00
NON SCHEDULED ITEMS
SANITARY INSTALLATIONS & C.P FITTINGS
2 NSR Providing & fixing 60x2cm. C.P. brass towelrail complete with
C.P. brass brackets fixed to wooden cleats with C.P. brass
screw.PARRYWARE C9948 Each 18.00 1200.00 21600.00
3 NSR Supplying & Fixing of CP soap tray fixed to the wall with PVC
rubber plug with CP brass screws Each 18.00 800.00 14400.00
4 NSR Providing and Fixing C.P. brass Ablution health faucet assembly
with 1.2 m long braided PVC hose with mounting bracket fixed
on wall complete.[FOR EWC] Each 12.00 500.00 6000.00
5 NSR Providing and fixing C.P. brass Two-way angle valve for EWC
points & for fixing Ablution Health Fauct of approved quality
conforming to IS:8931. 15 mm nominal bore Each 12.00 1400.00 16800.00
6 NSR Constructing brick masonary INSPECTION chamber 60x60x60
cm with bricks of class designation 50 in cement mortar 1:4 (1
cement : 4 coarse sand) including CI cover with frame LIGHT
WEIGHT complete as per design. With FPS bricksEach 2.00 6500.00 13000.00
TOTAL [V] 75800.00
VI
1 NSR Providing and fixing G.I Inlet fitting with 2 inlets 75 mm size
fabricated from 100 mm dia G.I pipes(approx. length=150mm
to 300mm) and welded G.I sockets, fixed to CI trap with lead
caulked joint and set in cement concrete as per standard
drawing including cost of Bitumastic paint complete. Each 24.00 1200.00 28800.00
TOTAL [VI] 28800.00
CI PIPES & FITTINGS
S.N. Description D.S.R. - Qty. Unit Rate (Rs.) Amount (Rs.)SEPTIC TANKSize :- Length = 7.50 M. Width = 2.65 M
Total Depth =2.50M
1 Earth work in excavation over areas including
disposal of excavated earth, lead upto 50m,
disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth 2.6.1 39.520 Cum 155.60 6149.31
In all kind of soil upto 1.5m to 3.0m. depth 2.6.1&2.26 29.290 Cum 201.85 5912.19
2 Providing and laying of cement concrete in base
excluding the cost of centring and shuttering by
1:2:4 (1 cement : 2 coarse sand : 4 gradded
stone aggregae 40mm nominal size)4.1.3 4.635 Cum 5466.30 25336.30
3 Brick work with brick of class designation 150 in
foundation and plinth in cement mortar (1
cement : 4 coarse sand) 6.1.1 24.897 Cum 4918.65 122459.63
4 Reinforced cement concrete work in slab with
1:2:4 (1 cement : 2 course sand : 4 graded
stone aggregate 20mm normal size). 5.3 4.242 Cum 6778.2 28753.12
5 Reinforcement for R.C.C. work including,
straightening, cutting bending binding and
placing in position complete. 5.22.1 320.000 Kg 64.95 20784.00
6 Centring and shuttering including struting ,
proping etc and removal of form for slab. 5.9.3 20.000 Sqm 401.65 8033.00
7 15mm cement plaster on rough side of mix 1:4
(1 cement : 4 coarse sand) 13.2.1 65.550 Sqm 189.40 12415.17
8 Providing M.S. foot rest including fixing with
20x20x10 cm. cement concrete block 1:3:6 (1
cement : 3 coarse sand : 6 gradded aggregate
of nominal size 20mm ) as per standard design
with 20x20mm sq bars.19.15.1 12.000 Nos. 275.50 3306.00
ESTIMATE FOR EXTERNAL PLUMBING WORKSPROPOSED RENOVATION WORK OF HOSTEL BLOCK E FOR N.I.T., RAIPUR (CHATTISGARH)
PART - A (SCHEDULED ITEMS AS PER D.S.R 2014)
9 Providing and fixing C.I. tee at the inlet and
outlet of septic tank. 7087 2.000 Nos. 600.00 1200.00
10 Providing & fixing 75mm dia vent pipes. 17.35.2.1 1.000 Rm. 709.10 709.10
11 Providing & fixing of 75mm dia cast iron terminal
guard. 17.56.2.1 1.000 No. 197.7 197.70
12 Providing and fixing in position precast RCC
manhole cover and frame of required shape and
approved quality.M.D. -10- Circular shape 500mm internal 19.19.2.2 2.000 No. 909.25 1818.50
M.D. -2.5- Circular shape 450mm internal 19.19.1.3 4.000 No. 902.80 3611.20
13 Making soak pit 2.5 m diameter 3.0 metre deep
with 45 x 45 cm dry brick honey comb shaft with
bricks of class designation 75 and S.W. drain
pipe 100 mm diameter, 1.8m long complete as
per standard design.With F.P.S. bricks 19.32.1 2.000 No. 18309.50 36619.00
TOTAL 277304.22
1 Excavating trenches in all kind of soil of required
width for pipes, cables etc. including excavation
for sockets and dressing of sides, ramming of
bottoms, depth upto 1.5 m. including getting
out the excavated soil & then returning the soil
as required,in layers not exceeding 20cm in depth including
consolidating each deposited layer by ramming,
watering, etc & disposig of surplus excavated soil
as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter. 2.10.1.2 125 RM 208.30 26037.50
2 Providing, laying and joining glazed stone ware
pipes grade 'A' with stiff mixture of cement
mortar in the proportion of 1:1 (1 cement : 1
fine sand) including testing of joints etc. a) 150mm diameter 19.1.2 125 M 314.35 39293.75
SCHEDULE OF QUANTITIES FOR EXTERNAL
3 Providing & laying cement concrete 1:5:10 (1
cement :5 coarse sand :10 graded stone
aggregate 40mm nominal size) alround S.W.
Pipes including bed concrete as per standard a) 150mm diameter S.W. Pipe 19.2.2 125 M 724.70 90587.50
4 Constructing brick masonry manhole in cement
mortar 1:4 (1 cement :4 coarse sand) RCC top
slab with 1:2:4 mix (1 cement :2 coarse sand :4
graded stone aggregate 20mm nominal size),
foundation concrete 1:4:8 mix (1 cement :4
coarse sand :8 graded stone aggregate 40mm
nominal size) inside plastering 12mm thick with
cement mortar 1:3 (1 cement :3 coarse sand)
finished with floating coat fo neat cement and
making channels in cement concrete 1:2:4 (1
cement :2 coarse sand :4 graded stone
aggregate 20mm nminal size) finished with a
19.7
Inside size 90x80cms and 45cms deep including
CI cover with frame (light duty) 455x610mm
internal diamensions total weight of cover and
frame to be not less than 38 kg (weight of cover
23 kg and weight of frame 15kg).With common burnt clay FPS (non modular)
bricks of class designation 75
19.7.1
(i) For Sewer Line 19.7.1 4.00 each 8507.00 34028.00
Inside size 90x120cms and 90cms deep
including CI cover with frame (MEDIUM duty)
455x610mm internal diamensions total weight of
cover and frame to be not less than 116 kg
(weight of cover 58 kg and weight of frame With common burnt clay FPS (non modular)
bricks of class designation 7519.7.2
(i) For Sewer Line 19.7.2.1 2.00 each 18304.45 36608.90
Extra for depth for manholes: Size 90x80cm with With common burnt clay FPS
(non modular) bricks of class designation 7.5 19.8.1.1 2.00 metre 5638.20 11276.40
Size 90x120cm with With common burnt clay
FPS (non modular) bricks of class designation 19.8.2.1 1.00 metre 6753.65 6753.65
5 Providing orange colour safety foot rests of
minimum 6 mm thick plastic encapsulated as per
IS:10910 on 12 mm dia steel bar conforming to
IS:1786 having minimum cross section as 23
mm x 25 mm and over all minimum length 263
mm and width as 165 mm with minimum 112
mm space between protruded legs having 2 mm
thread on top surface by ribbing or chequering
besides necessary and adequate anchoring
projections on tail length on 138 mm as per
standard drawing and suitable to with stand the
bend test and chemical resistance test as per
specifications and having manufacture's
permanent identification mark to be visible even
after fixing, including fixing in manholes with
30x20x15 cm cement concrete block 1:3:6 (1
cement : 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) complete as per
19.16 12.00 each 311.60 3739.20
TOTAL 248324.90
EXTERNAL WATER SUPPLY SYSTEM
1 Providing & fixing G.I. pipes complete with G.I.
fittings including trenching and refilling etc.
(external work)65mm nominal bore. 18.12.7 100 Rm. 524.25 52425.00
50mm nominal bore. 18.12.6 100 Rm. 399.50 39950.00
40mm nominal bore. 18.12.5 30 Rm. 334.15 10024.50
2 Supplying and fixing of specials for pressure 10% of item no.7 10239.95
3 Providing and fixing gate valve (with cap
complete with bolts, nuts, rubber insertion etc.65mm nominal bore. 18.17.5 1 Nos. 1287.75 1287.75
50mm nominal bore. 18.17.4 2 Nos. 750.75 1501.50
40mm nominal bore. 18.17.3 30 Nos. 585.50 17565.00
4 Constructing brick masonry chamber 600 x
600 x 750 mm inside with F.P.S. brick work
in cement mortar 1:4 (1 cement : 4 coarse
sand) for Sluice Valve / Air Valve, with C. I.
surface box 100 mm top diameter, 160 mm
bottom diameter and 180mm deep (inside) with
chained lid and RCC top slab with 1 : 2 : 4 mix
(1 cement : 2 coarse sand : 4 grade stone
aggregate 20 mm nominal size); necessary
excavation, foundation concrete 1:5:10 (1
cement : 5 fine sand: 10 graded stone
aggregate 40 mm nominal size) and inside
plastering with cement mortar 1 : 3 (1 cement
: 3 coarse sand ) 12 mm thick finished with a
floating coat of neat cement complete as per 18.33.1 2.00 Each 6754.30 13508.60
5 Constructing brick masonry chamber 900 x
900 x 1000 mm inside with F.P.S. brick work in
cement mortar 1:4 (1 cement: 4 coarse sand)
for Sluice Valve, with C.I.surface box 100 mm
top diameter, 160 mm bottom diameter and 180
mm deep (inside) with chained lid and RCC top
slab with 1:2:4 mix (1 cement: 2 coarse sand:4
grade stone aggregate 20mm nominal size);
necessary excavation, foundation concrete
1:5:10 (1 cement :5 fine sand: 10 graded stone
aggregate 40mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement:3
coarse sand ) 12 mm thick finished with a
floating coat of neat cement complete as per 18.34.1 1.00 Each 11673.35 11673.35
TOTAL 158175.65
DRAINAGE SYSTEM
1 Constructing brick masonry open surface drain
with bricks of class designation 75 in cement
mortar 1:4 (1 cement : 4 fine sand) including
earth excavation, 10cm thick bed concrete
1:5:10 (1 cement : 5 fine sand : 10 graded
stone aggregate 40mm nominal size) and 25mm
thick cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5mm
nominal size) for filling haunches including
12mm cement plaster 1:4 (1 cement : 4 coarse
sand ) with a floating coat of neat cement inside
the drain, its top and exposed side including
30cm drain 45cm average depth A.R. 150.00 Metre 1970.00 295500.00
45cm drain 60cm average depth A.R. 50.00 Metre 3000.00 150000.00
2 OVER HEAD WATER TANK AT PLINTH AREA
RATE OF 10KL 150000.00
TOTAL 595500.00
GRAND TOTAL 1279304.77
SAY 1279305.00
Sub Head Description As per NS
I Fire Suppression System Rs.281,864.00
Total C/F To Summary Rs.281,864.00
Total Rs.281,864.00
Name of Project : NIT RAIPUR HOSTEL BLOCK E
Name of Work : Estimate of Fire Fighting System
Project Summary
Sl.No. Description Unit Qty. Rate
Non DSR
Amount
Sub Head (I) - Fire Suppression
15 Supply and fixing CO2 type fire
extinguishers 4.5 kg. capacity(ISI Marked
IS: 2878 & TAC approved) complete with
initial charge and wall bracket, along with
supply of all materials and labour for
proper completion of work. Each 15 9874.00 148110.00
16Supply and fixing of fire extinguishers dry
chemical type 6 kg. capacity (ISI Marked
IS: 15683 & TAC approved) complete
with initial charge and wall bracket, along
with supply of all materials and labour for
proper completion of work. Each 15 8842.00 132630.00
17Supply and fixing of fire bucket, round
bottom made of G.I. sheet 9-11 litres
capacity duly painted as per fire brigade
design, supported on hanging bracket
chained and locked, initially filled with fine
river sand, water as per directions of
Engineer-in-Charge. Each 4 281.00 1124.00
Total Sub Head (I) 281864.00
NIT RAIPUR HOSTEL BLOCK E
Estimate of Fire Fighting System
top related