q7rf thermostat user manual - helvetic.ie€¦ · compu therm q7 rf quick set up remove cover and...

COMPUTHERM Q7 RF

Quick Set Up

Remove cover and insert 2xAA size batteries

You do not need to set up communication between the

Set the Day and Time

1. Click open cover located on bottom of Wireless Controller

2. Press the SET key to go in to the main screen.

3. Press the DAY key. On the screen top either 1,2,3,4,5,6,7 will begin to flash.

4. Press the Large Grey buttons - + keys adjust the day

5. Press the DAY key again and the hour icon starts to flash.

6. Press the Large Grey buttons - + to keys adjust the Hour.

7. Press the DAY key again and the Minute icon

8. Press the Large Grey buttons - + keys to adjust the Minute.

9. Press the SET key to finish the programming and go back to the main screen.

Manual function (Over ride Program mode)

1. Press the set button to reset screen display.

2. Press the HOLD button once, KEY Symbol will appear on the screen.

3. To turn on the panel press the + button and to

Degrees. Once panel is on you will see flame appearing on screen.

4. To return to programme mode press the SET key.

PROGRAMMING function

1. Hold the SET Button and at the same time Press the PROG Button.

2. On the Screen top, the numbers 1,2,3,4,5,6,7 will flash. This representing Monday, Tuesday, Wednesday etc.

3. Press the Large Grey buttons - + keys to adjust

4. NOTE: by selecting all number from 1 to 7 at once you are setting the same programme for ever day of the week. By selecting a

you are programming that day of the week.

5. Press the PROG button to move to the next stage. You will now see the HOUR & MINUTE flashing.

6. NOTE: This is Programme 1 of 6 different programmes

7. Now Press the Large Grey buttons - + keys to adjust the Time you want the Programme to BEGIN.

8. Press the PROG button to move to the next stage. You will now see the TEMPERATURE Flashing.

9. Now Press the Large Grey buttons - + keys to adjust the Temperature you want

10. NOTE: you can set the Temperature from minimum

11. Press the PROG button to move to the next stage. You will now see the HOUR & MINUTE flashing again.

12. NOTE: You have now moved to (P2) Programme 2, there are a total of 6 you can a

13. Continue pressing PRO button, this will allow you to move th

Note:if you procrastinate during the Programming stage this will result in the screen resettin

TO TURN ON THE BACK LIGHT

1. Press LIGHT once. The back light will turn on for 10 seconds.

HOW TO SET UP THE COMMUNICATION BETWEEN THE TRAN

1. Press the M/A key for 10 seconds, green LED will fla

2. On the Wireless Controller press transmitters SET key and press DAY key.

3. NOTE: After 10 second’s the green LED stops flashing

www.helvetic.ie Phone: 0863853000

THERM Q7 RF THERMOSTAT USER MANUAL

You do not need to set up communication between the receiver and Controller as this is factory set

Click open cover located on bottom of Wireless Controller

Press the SET key to go in to the main screen.

On the screen top either 1,2,3,4,5,6,7 will begin to flash.

+ keys adjust the day of week,1 representing Monday, 2 representing Tuesday etc.

starts to flash.

keys adjust the Hour.

icon starts to flash.

adjust the Minute.

Press the SET key to finish the programming and go back to the main screen.

Symbol will appear on the screen. You can now determine your desired temperature by pressing the +

the panel press the + button and to turn off press the - button. Example to turn off turn down to 7 Degrees and to turn on increase to 20

. Once panel is on you will see flame appearing on screen.

press the SET key.

Hold the SET Button and at the same time Press the PROG Button.

the numbers 1,2,3,4,5,6,7 will flash. This representing Monday, Tuesday, Wednesday etc.

+ keys to adjust the day of week you wish to programme.

NOTE: by selecting all number from 1 to 7 at once you are setting the same programme for ever day of the week. By selecting a

Press the PROG button to move to the next stage. You will now see the HOUR & MINUTE flashing.

ogrammes.

+ keys to adjust the Time you want the Programme to BEGIN.

button to move to the next stage. You will now see the TEMPERATURE Flashing.

+ keys to adjust the Temperature you want.

minimum 7 Degrees to 35 Degrees maximum.

button to move to the next stage. You will now see the HOUR & MINUTE flashing again.

NOTE: You have now moved to (P2) Programme 2, there are a total of 6 you can adjust to your own specification, 3 on and 3 off per 24

Continue pressing PRO button, this will allow you to move through each cycle.

if you procrastinate during the Programming stage this will result in the screen resetting itself back to main screen &

turn on for 10 seconds.

HOW TO SET UP THE COMMUNICATION BETWEEN THE TRANSMITTER AND RECIEVER – PLEASE REMEMBER THE UNIT IS ALREADY SET UP IN FACTORY

Press the M/A key for 10 seconds, green LED will flash and will enter in to communication mode.

press transmitters SET key and press DAY key.

green LED stops flashing on the receiver paring has been successful.

hone: 0863853000

THERMOSTAT USER MANUAL

etc.

You can now determine your desired temperature by pressing the + - Button.

xample to turn off turn down to 7 Degrees and to turn on increase to 20

NOTE: by selecting all number from 1 to 7 at once you are setting the same programme for ever day of the week. By selecting an individual number

djust to your own specification, 3 on and 3 off per 24 hours

g itself back to main screen & you will have to start from step1 again

REMEMBER THE UNIT IS ALREADY SET UP IN FACTORY