primbon rf

FALSE attenuation 3.54

TRUE emergency HO

FALSE SI13 sent BCCH via PBCCH

TRUE

TRUE

TRUE

TRUE

TRUE

TRUE MR BA table list in SACCH channel in 5bis,and 5tier

TRUE

C

B two BSC under one MSC should be different LAC

C PESQ (Perceptual evaluation Speech Quality) end to end measurement like decoder, can give test result by degradation cause, such as codec distortion, error,packet loss,delay, jitter,etc.

A The TLLI can be classified into four groups: Local TLLI: for normal operation between SGSN and user equipment.

Foreign TLLI: primarily used when crossing a routing area boundary.

Random TLLI: used for initial access or if the user equipment does not possess any of the above.

Auxiliary TLLI: is selected by the SGSN, but is not used as of now.

A PDP in SGSN, and APN (address translation and mapping DNS ) in GGSN

C

C Channel Request on RACH

D in SACCH channel (report BCCH,BSIC, and 6 strongest signal neighbor), Pre process in BCCH (module number,cell number,CGI,adjacent cell relation table)

B

D One group include 3 sector/sites, 12 frequency distributed to 4 sites, each sites have 3 freq

A

All

A&B&C

A& B State of GPRS MM include idle,Ready,standby

idle = GMM context is not established, MS is not reachable

Ready = MS can implement data transmision

Standby = GMM context is established, MS can receive paging but cannot implement data transmision

A,B Determine by Received level and Receive Quality

A & B& D

B SDCCH In underlaid and Overlaid layer HO

A,C,D Cause Drop is RLT,SACCH multi frame, ho thres, ho time

B,C,D,E

all

PESQ (Perceptual evaluation Speech Quality) end to end measurement like decoder, can give test result by degradation cause, such as codec distortion, error,packet loss,delay, jitter,etc.

Local TLLI: for normal operation between SGSN and user equipment.

Foreign TLLI: primarily used when crossing a routing area boundary.

Random TLLI: used for initial access or if the user equipment does not possess any of the above.

Auxiliary TLLI: is selected by the SGSN, but is not used as of now.

in SACCH channel (report BCCH,BSIC, and 6 strongest signal neighbor), Pre process in BCCH (module number,cell number,CGI,adjacent cell relation table)

75

One group include 3 sector/sites, 12 frequency distributed to 4 sites, each sites have 3 freq

Standby = GMM context is established, MS can receive paging but cannot implement data transmision

FALSE For a 900/1800 MHz Co-BCCH cell, it is recommended that this parameter be set to Yes.

TRUE

TRUE But can not do CS and PS at the same time

TRUE T3212 must set as same in same Location area, to avoid high Location update in border or in different LAC area

FALSE handover complete will sent to BSC through FACCH

FALSE Just MCS 5-MCS 9 using 8 PSK, for CS1-MCS4 using GMSK

TRUE

FALSE MR in SACCH channel

TRUE

C

D Layer where a cell is located. The network designed by Huawei has four layers: Umbrella (layer 4), Macro (layer 3), Micro (layer 2), and Pico(layer 1). Each layer can be set with 16 priorities.

D

C

B

C

B

A

A CGI = MCC+MNC+LAC+CI

B

A&B

A & B MCS 5-MCS 9

A,B,D

all

A,B,D

B&C

B,C,D,E

b&d

A & C & D

C

For a 900/1800 MHz Co-BCCH cell, it is recommended that this parameter be set to Yes.

T3212 must set as same in same Location area, to avoid high Location update in border or in different LAC area

Layer where a cell is located. The network designed by Huawei has four layers: Umbrella (layer 4), Macro (layer 3), Micro (layer 2), and Pico(layer 1). Each layer can be set with 16 priorities.

A1 B1 C1 D1 A2 B2 C2 D2 A3

9

13 14 15 16 17 18 19 20 21

25 26 27 28 29 30 31 32 33

37 38 39 40 41 42 43 44 45

49 50 51 52 53 54 55 56 57

61 62 63 64 65 66 67 68 69

73 74 75 1 2 3 4 5 6

B3 C3 D3

10 11 12

22 23 24

34 35 36

46 47 48

58 59 60

70 71 72

7 8