pe & ptfe diaphragm pumps - tapflotapflo.com/en/.../manuals/tapflo...pumps_2016_rev1.pdf ·...
Post on 18-Aug-2018
217 Views
Preview:
TRANSCRIPT
PE & PTFE
Diaphragm Pumps
edition 2016 rev 2
Read this instruction manual carefully,
before you install and operate the pump.
Pump models:
TR/TXR9
TR/TXR20
T/TX50
T/TX100
T/TX200
T/TX400
T800
CONTENTS
IOM manual Tapflo PE & PTFE series 2
0. GENERAL ................................................................................................................................................................................ 6
0.1. Introduction .................................................................................................................................................................... 6
0.2. Warning symbols ......................................................................................................................................................... 6
0.3. Qualification and training of personnel .......................................................................................................... 6
1. INSTALLATION ................................................................................................................................................................... 7
1.1. Operation principle ..................................................................................................................................................... 7
1.2. Receiving inspection .................................................................................................................................................. 7
1.3. Storage .............................................................................................................................................................................. 8
1.4. Foundation ...................................................................................................................................................................... 8
1.5. Suction and discharge piping ................................................................................................................................ 8
1.5.1. Rotary connections ........................................................................................................................................... 8
1.5.2. Connection of suction pipe .......................................................................................................................... 8
1.5.3. Connection of discharge pipe ..................................................................................................................... 8
1.6. Health and safety ......................................................................................................................................................... 9
1.6.1. Protection .............................................................................................................................................................. 9
1.6.2. Explosion hazardous environments – ATEX......................................................................................... 9
1.6.3. Air pressure ........................................................................................................................................................... 9
1.6.4. Noise level ........................................................................................................................................................... 10
1.6.5. Temperature hazards ..................................................................................................................................... 10
1.7. Air connection ............................................................................................................................................................. 10
1.7.1. Air treatment system ..................................................................................................................................... 11
1.8. Example of installation ........................................................................................................................................... 11
1.9. Recommended installations ................................................................................................................................. 12
1.9.1. Flooded ................................................................................................................................................................. 12
1.9.2. Self-priming ....................................................................................................................................................... 12
1.9.3. Submerged .......................................................................................................................................................... 12
2. OPERATION ........................................................................................................................................................................ 13
2.1. Before starting the pump ...................................................................................................................................... 13
2.2. Starting and operation ........................................................................................................................................... 13
2.2.1. Dry running......................................................................................................................................................... 13
2.2.2. Optimization of the pump lifetime ........................................................................................................ 13
2.3. Pump stopping............................................................................................................................................................ 14
3. MAINTENANCE ................................................................................................................................................................ 15
3.1. When the pump is new or reassembled ........................................................................................................ 15
3.1.1. Performance test ............................................................................................................................................. 15
CONTENTS
IOM manual Tapflo PE & PTFE series 3
3.2. Routine inspection .................................................................................................................................................... 15
3.3. Complete inspection ................................................................................................................................................ 15
3.4. Location of faults ....................................................................................................................................................... 16
3.5. TR9 / TR20 – Disassembly of the pump ......................................................................................................... 17
3.5.1. Before the disassembly procedure ......................................................................................................... 17
3.5.2. Disassembly procedure ................................................................................................................................ 17
3.6. TR9 / TR20 – Assembly of the pump ............................................................................................................... 19
3.6.1. Test run ................................................................................................................................................................. 19
3.7. T50-T800 – Disassembly of the pump ............................................................................................................ 20
3.7.1. Before the disassembly procedure ......................................................................................................... 20
3.7.2. Disassembly procedure ................................................................................................................................ 20
3.8. T50-T800 – assembly of the pump ................................................................................................................... 24
3.8.1. Test run ................................................................................................................................................................. 24
4. OPTIONS .............................................................................................................................................................................. 25
4.1. Drum pump – TD… ................................................................................................................................................... 25
4.2. Twin connections – TT… ........................................................................................................................................ 25
4.3. Filter press pump – TF… ......................................................................................................................................... 26
4.4. Barrier pump – TB… ................................................................................................................................................. 26
4.5. Pump with built-on dampener – TK … ........................................................................................................... 27
4.6. Pump with integrated flanges – T… -3D/-3A ............................................................................................. 27
5. SPARE PARTS .................................................................................................................................................................... 29
5.1. TR9 and TR20 – Spare parts drawing .............................................................................................................. 29
5.2. TR9 and TR20 – Spare parts list.......................................................................................................................... 30
5.3. T50-T100 – Spare parts drawing ........................................................................................................................ 31
5.4. T50-T100 – Spare parts list ................................................................................................................................... 31
5.5. T50-T100 – Spare parts - Options ..................................................................................................................... 32
5.6. T200-T400 – Spare parts drawing ..................................................................................................................... 34
5.7. T200-T400 – Spare parts list ................................................................................................................................ 34
5.8. T200-T400 – Spare parts - Options ................................................................................................................... 35
5.9. T800 – Spare parts drawing .................................................................................................................................. 37
5.10. T800 – Spare parts list ........................................................................................................................................ 38
5.11. Stocking recommendation .............................................................................................................................. 39
5.12. How to order parts .............................................................................................................................................. 40
5.13. Pump code ............................................................................................................................................................... 40
6. DATA ..................................................................................................................................................................................... 41
6.1. Capacity curves ........................................................................................................................................................... 41
CONTENTS
IOM manual Tapflo PE & PTFE series 4
6.2. Capacity changes ....................................................................................................................................................... 42
6.3. Technical data .............................................................................................................................................................. 42
6.4. Dimensions .................................................................................................................................................................... 43
6.5. Tightening torques ................................................................................................................................................... 45
6.6. Permitted loads on manifolds ............................................................................................................................. 45
7. WARRANTY ........................................................................................................................................................................ 46
7.1. Warranty form ............................................................................................................................................................. 46
7.2. Returning parts ........................................................................................................................................................... 47
7.3. Warranty ......................................................................................................................................................................... 47
CE CERTIFICATE
IOM manual Tapflo PE & PTFE series 5
EC declaration of conformity Machinery directive 2006/42/EC
Pressure equipment directive 97/23/EC, Category I
Tapflo AB declares that:
Product name: Air operated diaphragm pumps
Models: T…
is in conformity with the essential health and safety requirements and technical
construction file requirements of the EC Machinery directive 2006/42/EC,
and is in conformity with the Pressure Equipment Directive (PED) 97/23/EC
Category I.
Manufactured by Tapflo Sp. z o. o., Poland for:
Tapflo AB
Filaregatan 4
S-442 34 Kungälv
Sweden
Tapflo AB, January 2nd 2013
Håkan Ekstrand
Managing director
0. GENERAL
IOM manual Tapflo PE & PTFE series 6
0. GENERAL
0.1. Introduction
The Tapflo Air Operated Diaphragm Pump range is a complete series of pumps for industrial
applications. The pumps are designed to be safe, simple and easy to use and maintain. The
construction is seal-less and without rotating parts. The pumps are suitable for almost all
different chemicals used by the industry today.
With proper attention to maintenance, Tapflo Pumps will give efficient and trouble free
operation. This instruction manual will familiarise operators with detailed information about
installing, operating and maintaining of the pump.
0.2. Warning symbols
The following warning symbols are present in this instruction manual. This is what they say:
This symbol stands next to all safety instructions in this instruction manual where
danger to life and limb may occur. Observe these instructions and proceed with
utmost caution in these situations. Inform also other users of all safety instructions.
In addition to the instructions in this instruction manual, the general safety and
accident prevention regulations must be observed.
This signal stands at points in this instruction manual of particular importance for
compliance with regulations and directives, for correct work flow and for the
prevention of damage to and destruction of the complete dampener or its
subassemblies.
0.3. Qualification and training of personnel
The personnel in charge of installation, operation and maintenance of the pumps we produce
must be qualified to carry out the operations described in this manual. Tapflo shall not be held
responsible for the training level of personnel and for the fact that they are not fully aware of
the contents of this manual.
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 7
1. INSTALLATION
1.1. Operation principle
The Tapflo diaphragm pump is driven by compressed air. The two diaphragms are connected
by a diaphragm shaft and pushed back and forth by alternately pressurising the air chambers
behind the diaphragms using an automatically cycling air valve system.
The Suction Cycle:
Suction
One diaphragm creates a suction action in one chamber (on the right) when being pulled
back from the housing.
Discharge
The other diaphragm simultaneously transmits the air pressure to the liquid in the second
chamber (on the left) of the housing, pushing it towards the discharge port.
During each cycle the air pressure on the back of the discharging diaphragm is equal to the
head pressure on the liquid side. Tapflo diaphragm pumps can therefore be operated against
a closed discharge valve with no negative effect to the life of the diaphragms.
1.2. Receiving inspection
Although precaution is taken by us when packing and shipping, we urge you to carefully check
the shipment on receipt. Make sure that all parts and accessories listed on the packing list are
accounted for. Immediately report any damage or shortage to the transport company and to
us.
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 8
!
1.3. Storage
If the equipment is to be stored prior to installation, place it in a clean location. The pump
should be stored in an ambient temperature of 15°C (59°F) to 25°C (77°F) and relative humidity
below 65%. It should not be exposed to any heat source e.g. radiator, sun as this could result
in a negative way on the tightness of the pump. Do not remove the protective covers from the
suction, discharge and air connections which have been fastened to keep pump internals free
of debris. Clean the pump thoroughly before installation.
1.4. Foundation
The pump is equipped with vibration absorbing rubber feet. The pump will operate properly
without being fixed to a foundation. If fixation is needed for installation purposes, make sure
the foundation is able to absorb vibrations. It is essential for the operation of the pump to
mount the pump with the feet in a downward direction (see sketch in chapter 1.8 “Example of
installation”).
1.5. Suction and discharge piping
Suction and discharge piping should be fully supported and anchored near to but independent
of the pump. The piping connected to the pump should be a hose, to prevent undue stress and
strain on the pump connections and the piping.
1.5.1. Rotary connections The suction and discharge connections can be rotated 180°. This simplifies the assembly
and installation of the pump. If you wish to rotate the connections, screw a threaded nipple
into the connection and rotate it. On the larger models T200, T400 and T800 it will be easier if
the housing nuts are slightly released while turning the connections.
1.5.2. Connection of suction pipe
Remember that the suction pipe/connection is the most critical point, especially if the pump is
priming. Just a small leakage will dramatically reduce the suction capability of the pump. When
connecting the suction pipe, the following is recommended:
1) For satisfactory operation, use a reinforced hose (the suction power may otherwise shrink
the hose) or other flexible piping. The internal diameter of the hose should be the same
as on the suction connection (at the bottom of the pump) to have best suction capability.
2) Make sure that the connection between the hose and the pump is completely tight,
otherwise the suction capability will be reduced.
3) Always use as short suction pipe as possible. Avoid air pockets which can emerge with
long piping.
1.5.3. Connection of discharge pipe
For this connection it is only recommended to have a simple and positive flow connection. Use
a hose or flexible piping (minimum one meter) between the discharge connection and any rigid
fixed piping. Coil the hose at least one turn. All components (hose, pipe, valves etc.) on the
discharge piping must be designed for minimum PN 10.
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 9
1.6. Health and safety
The pump must be installed according to local and national safety rules.
The pumps are constructed for particular applications. Do not use the pump on
applications different from that for which it was sold without consulting us to ascertain
its suitability.
1.6.1. Protection
In the interest of health and safety it is essential to wear protective clothing and safety goggles
when operating, and/or working in the vicinity of Tapflo pumps.
1.6.2. Explosion hazardous environments – ATEX
The standard PE & PTFE series pumps are not allowed to operate in environments where there
is danger of explosion. Static electricity may occur in the pump under operation, which may
cause explosion and injury. Special conductive TX pumps are available for such applications.
Follow below instructions and local/national rules for safe use.
ATEX (directive 94/9/EC) classification of Tapflo TX pumps:
ATEX II 2 GD IIB c T4
Equipment group: II – all other explosive areas than mines;
Category group: 2 – high level of protection (can be used in zone 1);
Atmosphere: G – gas;
D – dust;
Explosion group: IIB – such as ethylene;
Type of protection: c – constructional safety;
Temperature class: T4 – in the event of a malfunction, the maximum temperature of a
surface that may be exposed to gas T4 = 135 °C.
Earth connection of the pump and other equipment
Connect a suitable earth wire to the stainless steel earth connection that is placed on the inside
of one of the pump housings. Connect the other end of the earth wire to earth and also make
sure that other equipment like hoses/pipes/containers etc. are properly earthed/connected.
1.6.3. Air pressure
The maximum air pressure for Tapflo pumps is 8 bar. Higher air pressure than 8 bar can damage
the pump and may cause injury to personnel in vicinity of the pump. If you intend to apply a
higher air pressure than 8 bar, please consult us.
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 10
1.6.4. Noise level
At tests, the noise level from a Tapflo pump has not exceeded 80 dB(A). Under some
circumstances, for example if the pump is operating under high air pressure at low discharge
head, the noise can be inconvenient or hazardous for personnel staying for long periods in the
vicinity of the pump. This hazard can be prevented by:
using suitable ear protection;
lowering the air pressure and/or raising the discharge head;
leading out the outgoing air from the room by connecting a hose to the muffler
connection of the pump;
using elastomer valve balls (EPDM, NBR or polyurethane) instead of PTFE, ceramic or
stainless steel, provided that the elastomer is compatible with the pumped liquid.
1.6.5. Temperature hazards
Raised temperature can cause damage on the pump and/or piping and may also be
hazardous for personnel in the vicinity of the pump/piping. Avoid quick temperature
changes and do not exceed the maximum temperature specified when the pump was
ordered. See also general max temperatures based on water in chapter 6 “DATA”.
When the pump is exposed to ambient temperature variations or if there is big difference
between the temperature of the product and the surrounding, the tightening torques of
the housing nuts should be checked periodically as part of preventive maintenance.
If a hot product is pumped, the pump should not stand still when filled for a longer period
of time. This could cause leakage from the valves and contamination and/or damage of the
air valve.
Below 0°C (32°F) plastic materials become more fragile what can cause accelerated wear of
parts made of these materials. This is a hazard that has to be accepted when pumping such
cold products. Also in such case, when a pump is not operational it should be drained of all
liquid.
Bear in mind that the viscosity of the product changes with temperature. This has to be
taken into consideration when selecting the pump.
1.7. Air connection
Screw the air hose into the air intake on the centre block of the pump with for example a quick
release coupling. For best efficiency, use the same hose diameter as the internal diameter of
the connection on the air intake.
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 11
1.7.1. Air treatment system
The air valve is constructed for oil-free air. Lubrication of the air is not allowed. However, if the
air is very dry (laboratory air), the air may be lubricated with water. Maximum air pressure is 8
bar. As prevention purpose, a filtration of the air by means of a 5 micron filter or finer is
recommended. Recommended air quality according to PN-ISO8573-1:2010 is particles class 6,
water class 7 and oil class 4. Dirt in the air can under unfortunate circumstances be the cause
of a breakdown.
To facilitate the operation of the pump we recommend an air treatment system connected to
the air supply. These components should be included:
1) Regulator to adjust the air pressure;
2) Manometer to read the actual pressure;
3) Needle valve to adjust the air flow (especially when operating the pump in the lower range
of performance);
4) Filter.
These components are included in Tapflo’s Air treatment system which can be ordered from
us.
1.8. Example of installation
1) Gate valve compressed air
2) Filter and pressure regulator
3) Flexible hose
4) Needle valve
5) Flexible piping
6) Gate valve suction
7) Gate valve discharge
8) Coiled flexible piping
9) Flow gauge
1. INSTALLATION
IOM manual Tapflo PE & PTFE series 12
1.9. Recommended installations
The Tapflo pump is flexible in the way you are able to install it. The in- and outlet ports can be
rotated more than 180° to fit various piping systems.
1.9.1. Flooded
The piping system is designed with a positive
suction head. This is the best way of
installation where it is necessary to completely
empty all liquid from the container, or where
viscous (thick) products are transferred.
NOTE! Do not exceed 0,7 bar suction
pressure! Higher pressure may cause
premature diaphragm failure and irregular
pump operation.
1.9.2. Self-priming
The Tapflo pump is designed to pull a high
vacuum. It is able to evacuate an empty
suction pipe without any damage to the
pump. The suction lift is up to 5 meters (16.4
ft.) from an empty suction pipe and up to 8
meters (26.2 ft.) from a wetted pipe. The
suction capability depends on the pump size
(see chapter 5 “DATA”).
1.9.3. Submerged
All Tapflo pumps may be submerged into the
liquid. It is important to make sure that all
components which are in contact with the liquid
are chemically compatible. The air exhaust
must be led to the atmosphere by means of a
hose.
NOTE!
Even if all above safety instructions are met and complied with, there still exists a minor danger
in the event of a leakage or mechanical damage of the pump. In such case the pumped product
can emerge on sealing areas and connections.
2. OPERATION
IOM manual Tapflo PE & PTFE series 13
2. OPERATION
2.1. Before starting the pump
Make sure the pump is installed according to the installation instruction (chapter 1).
Filling of the pump with liquid before start is not necessary.
When installation is new or reinstalled, a test run of the pump with water should be
conducted to make sure that the pump operates normally and does not leak.
When installation is new or reinstalled, check the pump housing nuts tightening torque
(see chapter 5.5 “Tightening torques”). After approximately one week of operation, the
torque should be checked again. This is important to prevent possible leakage.
2.2. Starting and operation
Open the discharge valve.
Note! Considering the suction capacity when air is still in the suction pipe, it is
recommended to start with low air pressure/flow (slowly) at the beginning. This
is not necessary if the pump is filled with liquid before start.
When the pump has been filled with liquid, the air pressure/flow may be raised in order
to increase the suction capacity of the pump.
The performance of the pump can be adjusted through the air supply by using a needle
valve and a pressure regulator. The performance can also be adjusted by normal flow
control on the discharge side of the system.
2.2.1. Dry running
Although the pump is prepared for dry running it is important to have in mind that long
periods of dry run may cause damage to the air valve and circlips. Also an empty pump
should operate at low speeds – controlled by a needle-valve.
2.2.2. Optimization of the pump lifetime
Running at full frequency (maximum air pressure/flow) continuously will cause
premature wear of the components. When there is possibility of the pump running dry
or/and at full frequency it is recommended to use an air valve with a PET piston. As a
general rule, we recommend to run at half of the maximum capacity of the pump. For
instance, a T100 pump should run continuously at maximum 50 l/min.
As stated in chapter 0 Tapflo recommends to use an appropriate air treatment system
in order to extend the pump’s lifetime.
If the air humidity is high, use of a water separator or air dryer is recommended.
Otherwise on the air discharge side due to decompression, icing on the muffler can
appear causing it to shrink and eventually it can shoot out of its socket.
If the ambient air is humid, icing can occur outside of the muffler. In such case it is
recommended to use a longer exhaust of the compressed air (ca. 500 mm / 19,7’’).
2. OPERATION
IOM manual Tapflo PE & PTFE series 14
If there is possibility of freezing at the air exhaust, it is good to pre-heat the air before it
reaches the air intake in order to raise the dew point of the air.
NOTE! Make sure that the air temperature does not exceed 50°C (122°F).
If icing / freezing is still a problem with the standard muffler, we recommend using our
heavy duty metal muffler. Contact us for more information.
2.3. Pump stopping
The pump can be stopped in two ways:
1) By closing of the discharge valve. The pressure from the system will stop the pump
automatically. The pump restarts easily when the valve is opened again.
NOTE! When using this method keep in mind that air must be supplied to the pump.
This is essential to keep the diaphragms in balance what protects them from premature
failure.
2) By cutting off the air supply.
NOTE! When using this method make sure that the discharge valve is opened to relief
the pumps pressure.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 15
3. MAINTENANCE
3.1. When the pump is new or reassembled
If the pump is new or reassembled after maintenance it is important to retighten the
pump housing nuts (pos. 37) after a few days of operation.
Make sure to use the right torque – see chapter 5.5 “Tightening torques”.
3.1.1. Performance test
When installation is new, a test run of the pump should be conducted. Gauge the capacity
at specific air pressure/flow. This information is useful for checking performance in the
future as wear takes place. You will be able to set schedules for maintenance of the pump
and to select spare parts to be kept on stock.
3.2. Routine inspection
Frequent observation of the pump operation is recommended to detect problems. A change
in sound of the running pump can be an indication of wearing parts (see chapter 3.4
"Location of faults" below).
Leaking liquid from the pump and changes of performance may also be detected. Routine
inspections should be conducted frequently.
3.3. Complete inspection
The intervals for a complete inspection depend upon the operation conditions of the pump.
The characteristics of the liquid, temperature, materials used in the pump and running time
decide how often a complete inspection is necessary.
Nevertheless, Tapflo recommend to inspect the pump at least once a year. Parts from KIT
AIR and KIT LIQ should be changed during inspection. Tapflo recommend KIT VAL to be
changed once per 2 years as well. See paragraph 5.11 for detailed KIT content.
If a problem has occurred, or if the pump is in need of a complete inspection, refer to
chapters 3.4 "Location of faults" and 3.5, 3.7 "Dismantling of the pump". You are of course
warmly welcome to consult us for further help.
Parts that are subject to wear should be kept in stock, see our recommendations in chapter
4.7 “Stocking recommendation”.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 16
3.4. Location of faults
PROBLEM POSSIBLE FAULT POSSIBLE SOLUTION
The pump does not run
The air pressure is to low Increase air pressure via a filter-regulator
The air connection is blocked Check / clean air supply connection
Muffler is blocked Check / clean / replace muffler
Air valve is defective Clean / replace complete air valve
Dirt in the pump chamber Remove debris from the chambers
Diaphragm breakdown Replace diaphragm
The suction is bad
Suction connection is not tight Tighten the suction line
Suction connection is blocked Clean suction line
Muffler is blocked Check / clean / replace muffler
Valve balls are blocked or damaged Check dimensions and shape of valve balls
Valve seats are worn
Pump starts with high pressure
Air in suction / discharge line
Dry suction against discharge pressure
Check dimensions and shape of valve seats
Start the pump slowly (see chapter 2.2)
Vent suction / discharge line
Wet the pump / start without discharge pressure
The pump runs irregular
Valve balls are blocked Check dimensions and shape of valve balls
Sealing in centre block
Air valve is defective
Replace sealing
Clean / replace air valve
Diaphragm breakdown
Valve seats are worn
Icing on the muffler
Replace diaphragm
Check dimensions and shape of valve seats
Improve air quality (see chapters 1.7.1 and 2.2.2)
Bad flow/pressure
Pressure fall in air supply
Pressure losses on suction side
Air supply / air valve leaking
Increase air pressure via a filter-regulator
Check/change installation on suction side
Check / repair / replace air supply / air valve
Suction or air connection blocked Check / clean air supply / suction connection
Muffler is blocked Check / clean / replace muffler
Valve ball worn or broken
Valve seats are worn
Check dimensions and shape of valve balls
Check dimensions and shape of valve seats
Air in liquid Seal suction line; check / refill container
Diaphragm breakdown
Icing on the muffler
Check / replace diaphragms
Improve air quality (see chapters 1.7.1 and 2.2.2)
Liquid leaks from the pump
Screws on the housing not properly
tightened
O-rings on manifolds damaged
Damaged diaphragm
Tension / stress form the installation
Check tightening torques of the screws
Replace O-rings
Check / replace diaphragms
Adjust installation, eliminate stress, when using a
dampener provide separate support for it (see
dampener IOM manual).
Liquid comes out of the
muffler
Diaphragm breakdown Replace diaphragm
Diaphragm breakdown
Wrong selection of material
Too high pressure in the installation
Long periods of dry running
Too high pressure on suction side
Contact us for information on material selection
Use air treatment system for protection
When dry, run pump slowly (see chapter 2.2)
Make sure there is pressure balance between the
air and liquid side of the diaphragm
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 17
3.5. TR9 / TR20 – Disassembly of the pump
The numbers put in brackets, refer to the part numbers in the spare part drawings and spare
part lists in chapter 4 “SPARE PARTS”.
3.5.1. Before the disassembly procedure
Be sure to drain all liquid from the pump. Cleanse or neutralize the pump thoroughly.
Disconnect the air supply and then the suction and discharge connections.
3.5.2. Disassembly procedure
Fig. 3.5.1 PTFE only
Using a pair of pliers unscrew the plugs [571] and lift the
PE covers [1181].
Fig. 3.5.2
Unscrew the housing nuts [37] and carefully remove the
pin screws [14].
Fig. 3.5.3
Lay down the pump on one side and lift one of the
housings [11].
Fig. 3.5.4
Lift the loose manifolds [13] and centre block [12] from
the second housing [11].
Fig. 3.5.5
Screw a pin screw into the hole of the spacer sleeve [19].
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 18
Fig 3.5.6
Lift and pull out the spacer sleeve [19].
Fig 3.5.7
Take out the valve rods [20] and [21],
Fig 3.5.8
Unscrew the diaphragms [15] form the air valve [61].
Fig 3.5.9
Using pliers remove both circlips [27] from the centre
block [12].
Attention! While doing this, cover yourself with your
other hand, as the circlip easily flips away.
Fig 3.5.10
Press out the air valve [61] by means of a pressing
device. Be careful not to damage the brass edges of the
air valve.
The pump is now completely disassembled. Check all components for wear or damage and
replace if necessary.
When air valve is removed from the centre body check the external O-rings (6 x pos. 30)
condition and replace if necessary.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 19
3.6. TR9 / TR20 – Assembly of the pump
The assembly procedure is done in the reverse order to the disassembly.
Nevertheless there are a few things that you have to remember in order to assemble the
pump correctly.
Fig. 3.6.1
When putting the air valve [61] into the centre block
[12], apply some water or alcohol on the
O-rings to provide smooth insertion of the air valve. It
is recommended to use a pressing device for this
operation.
NOTE! When inserting the TR9 / TR20 size air valve,
replace the shaft with a screw and a nut to make sure
the air valve assembly remains properly fastened.
Fig. 3.6.2
When screwing in the diaphragms [15] on the shaft
[16], the holes in the diaphragms must align with the
holes in the centre block [12]. Sometimes it is
necessary to turn the diaphragm back a little bit in
order to align the holes.
Fig. 3.6.3
When putting in the pin screws [14] take extra care not
to damage the diaphragms [15] with the pin screw
thread.
Fig. 3.6.4
When fastening the domed nuts, remember to do it
according to the tightening procedure and with the
appropriate torque.
NOTE! After a few weeks of operation retighten the
domed nuts with the appropriate torque.
3.6.1. Test run
We recommend you to conduct a test run of the pump before installing it in the system, so
no liquid gets wasted if the pump leaks or perhaps does not start accordingly to wrong
assembly of the pump.
After a few weeks of operation retighten the nuts with appropriate torque.
3. MAINTENANCE
3.7. T50-T800 – Disassembly of the pump
The numbers put in brackets, refer to the part numbers in the spare part drawings and spare
part lists in chapter 4 “SPARE PARTS”.
3.7.1. Before the disassembly procedure
Be sure to drain all liquid from the pump. Cleanse or neutralize the pump thoroughly.
Disconnect the air supply and then the suction and discharge connections.
3.7.2. Disassembly procedure
Fig. 3.7.1 PTFE only
Using a pair of pliers unscrew the plugs [571] and lift the
PE covers [1181].
Fig. 3.7.2
Unscrew the housing nuts [37] and carefully remove the
pin screws [14].
Fig. 3.7.3
Lay down the pump on one side and lift one of the
housings [11].
Fig. 3.7.4
Lift the loose manifolds [13] and centre block [12] from
the second housing [11].
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 21
Fig. 3.7.5
To remove the spacer sleeve [19], use a plastic rod and
a hammer to knock it out.
NOTE! Be careful not to deform the spacer sleeve.
Fig. 3.7.6
Insert our special tool or pin screw [14] into the orifice
in the spacer sleeve [19], rotate it.
Fig. 3.7.7
Pull out the spacer sleeve [19].
Fig. 3.7.8
Pull out the lower sleeve [212], valve seat [222] and O-
ring [43].
Fig. 3.7.9
Pull out the upper sleeve [202] alongside with the valve
seat [222], O-ring [43] and the blocking pin [2021].
Fig. 3.7.10
Unscrew the diaphragm [15] from one side of the pump.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 22
Fig. 3.7.11
Take out the second diaphragm [15] along with the shaft
[16].
a) Circlip mounted air valve – T/TX50, T100 and T800
Fig. 3.7.12
Using pliers remove both circlips [27] from the centre
block [12].
Attention! While doing this, cover yourself with your
other hand, as the circlip easily flips away
Fig. 3.7.13
Press out the air valve [61] by means of a pressing
device. Be careful not to damage the brass edges of the
air valve.
b) Plate mounted air valve – T/TX100, T/TX200, T/TX400 from s/n 1106
Fig. 3.7.14
Unscrew plate screws [2711] from both sides of the
centre body [122] and take out the left and right plate
[271].
Fig. 3.7.15
Press out the air valve [61] by means of a pressing
device. Be careful not to damage the brass edges of the
air valve.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 23
c) Threaded air valve – T200 from s/n 0803-… until 1105-… and
T400 from s/n 0801-… until 1105-…
Fig. 3.7.16
Carefully unscrew both air valve end caps by means of a
mounting tool [282].
Fig. 3.7.17
Push out by hand the air valve shaft and piston.
Fig. 3.7.18
To push out the cylinder, use the other side of the
mounting tool. Use a pressing device to remove the air
valve cylinder from the centre body [123].
The pump is now completely disassembled. Check all components for wear or damage and
replace if necessary.
When air valve is removed from the centre body check the external O-rings (6 x pos. 30)
condition and replace if necessary.
3. MAINTENANCE
IOM manual Tapflo PE & PTFE series 24
3.8. T50-T800 – assembly of the pump
The assembly procedure is done in the reverse order to the disassembly.
Nevertheless there are a few things that you have to remember in order to assemble the
pump correctly.
Fig. 3.8.1
When putting the air valve [61] into the centre block
[12], apply some water or alcohol on the O-rings to
provide smooth insertion of the air valve.
It is recommended to use a pressing device for this
operation.
Fig. 3.8.2
When there is need to replace the diaphragm pin screw
[1652], while screwing it into the diaphragm [15] make
sure the pin screw goes all the way.
Fig. 3.8.3
When screwing in the diaphragms [15] on the shaft [16],
the holes in the diaphragms must align with the holes in
the centre block [12]. Sometimes it is necessary to turn
the diaphragm back a little bit in order to align the holes.
Fig. 3.8.4
When fastening the domed nuts, remember to do it
according to the tightening procedure and with the
appropriate torque.
NOTE! After a few weeks of operation retighten the
domed nuts with the appropriate torque.
3.8.1. Test run
We recommend you to conduct a test run of the pump before installing it in the system, so
no liquid gets wasted if the pump leaks or perhaps does not start accordingly to wrong
assembly of the pump.
After a few weeks of operation retighten the nuts with appropriate torque.
4. OPTIONS
IOM manual Tapflo PE & PTFE series 25
4. OPTIONS
4.1. Drum pump – TD…
This solution is ideal if we want the pump to be mobile. It is
equipped with a stainless steel carrying handle and a
suction tube which is screwed in directly in to the inlet
manifold. The standard tube length is 2 meters. You can
easily take the pump off a barrel or container and move it
to another one.
Available for pump sizes:
TDR20, TD50 and TD100
Additional / different parts:
Art. no Q-ty Description Material
6-xxx-63 1 Drum inlet PE, PTFE
6-xxx-64 1 Pump tube PP, PTFE
6-xxx-65 1 Handle AISI 316L
4.2. Twin connections – TT…
Tapflo pumps can be fitted with double inlet/outlet. This
allows to have “two pumps in one”. It is used for blending,
mixing or recirculation of liquids. Both pump chambers are
separated so, the liquid does not mix.
Available for pump sizes:
TRT9, TRT20, TT50, TT100, TT200 and TT400
Additional / different parts:
Art. no Q-ty Description Material
6-xxx-130 2 Twin inlet/outlet PE, PTFE
4. OPTIONS
IOM manual Tapflo PE & PTFE series 26
4.3. Filter press pump – TF…
The Tapflo filter press pump is a ready, compact product
that can be installed directly on the filter press. The pump is
equipped with a booster which amplifies the pressure in a
2:1 ratio. As a result we can achieve up to 16 bar on the
discharge of the pump (depending on pump size). As a
standard the booster is equipped with a pressure regulator
and two manometers. In comparison to a standard pump
the TF version is equipped with reinforcement plates and
special air valve with PET piston (6-xxx-61-318).
We also recommend to use aluminium centre body (-6A
option) instead of standard PP for better durability.
Available for pump sizes:
TF50, TF100, TF200 and TF400
Additional / different parts:
Art. no Q-ty Description Material
6-xxx-1171 1 Long reinforcement plate AISI 316L
6-xxx-1172 1 Short reinforcement plate AISI 316L
6-xxx-1175 1 Booster mounting plate AISI 316L
6-xxx-14 2 Pin screws AISI 316L
6-xxx-99 1 Booster complete set -
4.4. Barrier pump – TB…
With its special construction and control system the barrier
pump is perfect when diaphragm rupture has to be
immediately detected in order to avoid product leak to the
environment and the air distribution system. When rupture
is detected the pump is automatically stopped and an
alarm can be generated.
Available for pump sizes:
TRB20, TB50, TB100, TB200 and TB400
Additional / different parts:
Art. no Q-ty Description Material
6-xxx-129 2 Spacer PP, PE, AISI 316L, Aluminium
6-xxx-139 2 Long inlet/outlet PE, PTFE
6-xxx-149
4/6/8
* Pin screw
AISI 304
6-xxx-151 2 Diaphragm – air side EPDM, PTFE, NBR
6-xxx-152 2 Diaphragm – liquid side EPDM, PTFE, NBR
6-xxx-153 4/6** O-ring FKM, NBR, EPDM
6-xxx-159 2*** Diaphragm spacer PP, PE, AISI 316L, Aluminium
6-xxx-169 1 Diaphragm shaft AISI 316L
6-xxx-339 2 Spacer plug PE
*4 for TRB20, 6 for TB50 and TB100, 8 for TB200 and TB400
** 4 for TRB20 and TB50; 6 for TB100, TB200 and TB400
**Only TB200 and TB400
4. OPTIONS
IOM manual Tapflo PE & PTFE series 27
4.5. Pump with built-on dampener – TK …
If you are looking for an effective way to eliminate pressure
variations on the pump discharge and you have limited
space in your installation, the built-on dampener is an ideal
solution. It provides all the advantages of using a standard
Tapflo DT dampener but is a compact solution. The
dampener housing is also the pump manifold so you do not
have to worry about connecting the dampener to the pump.
This solution does not affect the pump flow nor the
dampening effect.
Available for pump sizes:
TRK20, TK50, TK100, TK200
Additional / different parts:
Art. no Q-ty Description Material
DTK-xxx 1 Built-on dampener assembly -
6-xx1-112 1 Dampener housing /
pump outlet PE, PTFE
6-xx1-12 1 Dampener centre body PP
6-xx0-15 1 Dampener diaphragm EPDM, PTFE, NBR, PTFE 1705b
6-xx0-1652 1 Dampener grub screw St45H
6-xx0-37 8/12/16**** Dampener nut AISI 316
6-xx0-38 8/12/16**** Dampener washer AISI 316
6-xx0-36 3/5* Dampener PE seal PE
6-xx0-47 3/5/10** Dampener O-ring NBR, EPDM, FKM
6-xx1-16 1 Dampener shaft AISI 316L
6-xx1-14 4/6/8*** Dampener pin screw AISI 316
6-xx1-25 1 Dampener muffler PPM-F
6-xx1-27 1 Dampener blocking ring PE
*3 for TRK20, 5 for TK50, TK100 and TK200
**3 for TRK20, 5 for TK50 and TK200, 10 for TK100
***4 for TRK20, 6 for TK50 and TK100, 8 for TK200
**** 8 for TRK20, 12 for TK50 and TK100, 16 for TK200
4.6. Pump with integrated flanges – T… -3D/-3A
Pumps with integrated flanges are a robust and solid
design. When there is a risk of transferring of vibration from
the installation to the pump, the solid manifolds provide
better stability and sealing for the pump. Using this solution
we can connect the pump to the installation by a flange
(DIN, ANSI) or through a BSP thread.
Available for pump sizes:
T50, T100, T200, T400
4. OPTIONS
IOM manual Tapflo PE & PTFE series 28
Additional / different parts:
Art. no Q-ty Description Material
6-xxx-725-2 2 DIN Integrated flange PE, PTFE
6-xxx-725-9 2 ANSI integrated flange PE, PTFE
6-xxx-131 8 Threaded insert PET
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 29
5. SPARE PARTS
5.1. TR9 and TR20 – Spare parts drawing
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 30
5.2. TR9 and TR20 – Spare parts list
Pos. Q-ty Description Material KIT LIQ KIT AIR
11 2 Housing PE or PTFE
12 1 Centre block PP
13 2 In/Outlet PE or PTFE
14 4 Pin screw A4-80
15 2 Diaphragm EPDM*, PTFE, NBR* or FKM x
16 1 Diaphragm shaft (part of air valve assembly)
AISI 316L
17 4 Rubber foot NBR
18 4 O-ring set (in/outlet) PTFE/EPDM, EPDM, FKM, NBR* or FEP/FKM*** x x
19 2 Spacer sleeve PE or PTFE
20 2 Lower rod PTFE x
21 2 Upper rod PTFE x
22 2 Pin PTFE x
25 1 Muffler PP x
27 2 Circlip Cr3 coated steel
30 6 O-ring NBR (standard), EPDM or FKM
33 2 Plug PE or PTFE
37 8 Nut A4-70
38 8 Washer A4-70
57 8 Nut cover PP
61 1 Air valve complete Body: brass (standard), AISI 316L or PET,
O-rings: NBR (standard), EPDM or FKM x
Stainless steel reinforcement (std. on ATEX
PTFE)
117 2 Reinforcement plate AISI 316L
147 4 Pin screw A4-80
Stainless steel / PE reinforcement**
1173 2 Reinforcement plate AISI 316L
1181 2 Cover PE
147 4 Pin screw A4-80
571 4 Plug PE
Twin connection
130 2 Twin in/outlet PE, PTFE
Drum pump*
63 1 Drum inlet PE, PTFE
64 1 Pump tube PP, PTFE
65 1 Handle AISI 316L
Valve ball version*
23 4 Valve ball EPDM, PTFE, NBR,
FKM, AISI 316L, PU
191 2 Spacer sleeve PE, PTFE
201 2 Upper sleeve PE, PTFE
211 2 Lower sleeve PE, PTFE
221 4 Valve ball stop PE, PTFE
43 4 OP-ring PTFE
Built-on dampener*
DTK
9/20 1
Dampener for TK pump
version PE, PTFE
Flange connections*
70 2 Flange pipe (thread) PE, PTFE
71 2 ANSI flange ring PP, PTFE, AISI316L
73 2 DIN flange ring PP, PTFE, AISI316L
712 2 JIS flange ring PP, PTFE, AISI316L
721 2 Integrated manifold with loose flange
PP, PTFE
External air supply
36 2 Centerblock sealing PE
47 2 O-ring NBR (std.),
EPDM, FKM
124 1 Centerblock PP
161 1 Shaft AISI 316L
Double diaphragm system*
129 1 Set of spacers (right + left) PP
139 2 In/outlet PE, PTFE
149 4
Pin screw for PE pump AISI 316L
1497 Pin screw for PTFE pump
151 2 Air side diaphragm EPDM*, PTFE,
NBR* or FKM
152 2 Liquid side diaphragm EPDM*, PTFE,
NBR* or FKM
153 4 Diaphragm O-ring EPDM, FKM,
NBR
169 1 Diaphragm shaft (part of air valve assembly)
AISI 316L
339 2 Spacer plug PP
619 1 Air valve complete See pos.61
* = TR20 only
** = Standard on PTFE pumps from serial number 1012 ....
*** = Standard in pumps with PTFE diaphragms from
serial No 1301 …. (TR20) and from 1405 …. (TR9)
FEP/FKM O-rings do not fit on older in/outlets
(pos. 13). Older pumps have PTFE/EPDM as standard.
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 31
5.3. T50-T100 – Spare parts drawing
5.4. T50-T100 – Spare parts list
Pos. Q-ty Description Material KIT
LIQ
KIT
AIR
KIT
VAL
11 2 Housing PE, PTFE
12 1 Centre block PP
13 2 In/Outlet PE, PTFE
14 6 Pin screw A4-80
15 2 Diaphragm EPDM, PTFE, NBR, FKM* x
16 1 Diaphragm shaft AISI 304L x
17 4 Rubber foot NBR
18 4 O-ring set (in/outlet) PTFE/EPDM, EPDM, FKM, NBR, FEP/FKM*** x x
19 2 Spacer sleeve PE, PTFE x
202 2 Upper sleeve PE, PTFE, AISI 316L x
2021 2 Blocking pin PTFE, PE** x
212 2 Lower sleeve PE, PTFE, AISI 316L x
22 4 Valve ball stop PE1000, PTFE, PU, AISI 316L x
222 4 Valve seat PE1000, PTFE, PU, AISI 316L x
23 4 Valve ball EPDM, PTFE, NBR, FKM, AISI 316L, PU or ceramic x
25 1 Muffler PP x
26 1 Air intake adapter Galvanized brass
27 2 Circlip Cr3 coated steel
30 6 O-ring NBR (standard), EPDM, FKM
33 2 Plug PE, PTFE
36 2 Centerblock seal PE x
37 12 Nut A4-70
38 12 Washer A4-70
43 4 O-ring (valve seat) EPDM, PTFE, NBR, FKM x
47 2*/4** O-ring (back up for 36) NBR (standard), EPDM, FKM x
57 12 Nut cover PP
61 1 Air valve complete Body: brass (standard), AISI 316L or PET,
O-rings: NBR (standard), EPDM or FKM x
* = T50 only
** = T100 only
*** = FEP/FKM standard on pumps with PTFE diaphragms from serial No 1106 .... FEP/FKM O-rings do not fit on older
in/outlets (pos. 13). Older pumps have PTFE/ EPDM in std.
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 32
5.5. T50-T100 – Spare parts - Options
Stainless steel reinforcement (std. on ATEX PTFE)
117 2 Reinforcement plate AISI 316L
147 6 Pin screw A4-80
Stainless steel / PE reinforcement
1173 2 Reinforcement plate AISI 316L
1181 2 Cover PE
147 6 Pin screw A4-80
571 4*/8** Plug PE
Drum pump
63 1 Drum pump inlet PE, PTFE
64 1 Pump tube PP, PTFE
65 1 Handle AISI 316L
Plate mounted air valve (std. in TX100 form 1106)
122 1 Centerblock PP
271 1 Set of 2 plates AISI 316L
2711 8 Screws A4-70
Flange connections
70 2 Flange pipe (thread) PE, PTFE
71 2 ANSI flange ring PP, PTFE,
AISI316L
73 2 DIN flange ring PP, PTFE,
AISI316L
712 2 JIS flange ring PP, PTFE,
AISI316L
721 2 Integrated manifold with loose flange
PP, PTFE
Built-on dampener
DTK 1 Dampener for TK
pump version PE, PTFE
High lift seats
203 2 Upper sleeve – high
lift PE, PTFE
213 2 Lower sleeve – high lift
PE, PTFE
External air supply
124 1 Centerblock PP
26 2 Air intake adapter Brass
Twin connection
130 2 Twin in/outlet PE, PTFE
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 33
Diaphragm stroke sensor
121 1 Centerblock for stroke sensor
PP
43 1 O-ring NBR, FKM,
EPDM
74 1 Inductive sensor CuZn
75 1 Sensor cap PP
76 1 Sensing plate AISI 316L
750 1 Cable gland PP
Double diaphragm system
129 1 Set of spacers (right +
left) PP
139 2 In/outlet PE, PTFE
149
4
Pin screw for PE pump
A4-80 1497
Pin screw for PTFE
pump
151 2 Air side diaphragm EPDM, PTFE,
NBR or FKM
152 2 Liquid side diaphragm EPDM, PTFE,
NBR or FKM
153 4*/6** Diaphragm O-ring EPDM, FKM,
NBR
159 2** Diaphragm spacer
169 1 Diaphragm shaft AISI 304L
339 2 Spacer plug PP
Integrated flange
725-2 2 DIN integrated flange PE, PTFE
725-9 2 ANSI integrated flange
PE, PTFE
113 8 Threaded inserts PET
Pump with pressure booster
99 1 Booster -
990 1 Booster mounting plate
AISI 304
996 4 Booster mounting screw
A4-70
997 4 Booster mounting washer
A4-80
1171 1/0*** Reinforcement plate AISI 304
1172 1/2*** Reinforcement plate AISI 304
37 6 Additional nuts AISI 304
38 6 Additional washers AISI 304
57 4 Additional nut covers PP
147 2 Additional pin screws A4-80
* = T50 only
** = T100 only
*** = For Festo booster 2 x 1172, for SMC and Metal Work 1 x 1171 and 1 x 1172
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 34
5.6. T200-T400 – Spare parts drawing
5.7. T200-T400 – Spare parts list
Pos. Q-ty Description Material KIT
LIQ
KIT
AIR
KIT
VAL
11 2 Housing PE, PTFE
122 1 Centre block PP
13 2 In/Outlet PE, PTFE
14 8 Pin screw AISI 316
15 2 Diaphragm EPDM, PTFE, NBR, PTFE 1705b x
16 1 Diaphragm shaft AISI 304L x
17 4 Rubber foot NBR
18 4 O-ring set (in/outlet) PTFE/EPDM, EPDM, FKM, NBR, FEP/FKM** x x
19 2 Spacer sleeve PE, PTFE x
202 2 Upper sleeve PE, PTFE, AISI 316 x
2021 2 Blocking pin PTFE, PE x
212 2 Lower sleeve PE, PTFE, AISI 316 x
22 4 Valve ball stop PE1000, PTFE x
222 4 Valve seat PE1000, PTFE, PU, AISI 316, PTFE 1635 x
23 4 Valve ball EPDM, PTFE, NBR, FKM, AISI 316, PU or ceramic x
25 1 Muffler PP x
26 1 Air intake adapter Galvanized brass
271 1 Set of 2 plates AISI 316
2711 8 Screw AISI 316
30 6 O-ring NBR (standard), EPDM, FKM
33 2 Plug PE, PTFE
36 2 Centerblock seal PE x
37 16 Nut AISI 304
38 16 Washer AISI 304
43 4 O-ring (valve seat) EPDM, PTFE, NBR, FKM x
47 2 O-ring (back up for 36) NBR (standard), EPDM, FKM x
57 16 Nut cover PP
61 1 Air valve complete Body: brass (standard), AISI 316 or PET,
O-rings: NBR (standard), EPDM or FKM x
* = T200 from s/n 0803… to 1105… and T400 from 0801…. to 1105….
** = FEP/FKM standard on pumps with PTFE diaphragms from serial No 1106 .... FEP/FKM O-rings do not fit on older in/outlets (pos. 13). Older
pumps have PTFE/ EPDM in std.
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 35
5.8. T200-T400 – Spare parts - Options
Stainless steel reinforcement (std. on ATEX PTFE)
117 2 Reinforcement plate AISI 316L
147 8 Pin screw A4-80
Stainless steel / PE reinforcement
1173 2 Reinforcement plate AISI 316L
1181 2 Cover PE
147 8 Pin screw A4-80
571 4 Plug PE
Twin connection
130 2 Twin in/outlet PE, PTFE
Diaphragm stroke sensor
1221 1 Centre block for stroke sensor
PP
43 1 O-ring NBR, FKM,
EPDM
74 1 Inductive sensor CuZn
75 1 Sensor cap PP
76 1 Sensing plate AISI 316L
750 1 Cable gland PP
Flange connections
70 2 Flange pipe (thread) PE, PTFE
71 2 ANSI flange ring PP, PTFE,
AISI316L
73 2 DIN flange ring PP, PTFE,
AISI316L
712 2 JIS flange ring PP, PTFE,
AISI316L
721 2 Integrated manifold with loose flange
PP, PTFE
High lift seats
203 2 Upper sleeve – high lift PE, PTFE
213 2 Lower sleeve – high lift PE, PTFE
External air supply
124 1 Centre block PP
26 2 Air intake adapter Brass
Integrated flange
725-2 2 DIN integrated flange PE, PTFE
725-9 2 ANSI integrated flange PE, PTFE
113 8 Threaded inserts PET
Built-on dampener (T200 only)
DTK 1 Dampener for TK
pump version PE, PTFE
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 36
Double diaphragm system
129 1 Set of spacers (right +
left) PP
139 2 In/outlet PE, PTFE
149
8
Pin screw for PE pump
A4-80 1497
Pin screw for PTFE
pump
151 2 Air side diaphragm EPDM, PTFE,
NBR or FKM
152 2 Liquid side diaphragm EPDM, PTFE,
NBR or FKM
153 6 Diaphragm O-ring EPDM, FKM,
NBR
159 2 Diaphragm spacer
169 1 Diaphragm shaft AISI 304L
339 2 Spacer plug PP
Pump with pressure booster
99 1 Booster -
990 1 Booster mounting plate
AISI 304
996 4 Booster mounting screw
A4-70
997 4 Booster mounting washer
A4-80
1171 1/0* Reinforcement plate AISI 304
1172 1/2* Reinforcement plate AISI 304
37 6 Additional nuts AISI 304
38 6 Additional washers AISI 304
57 4 Additional nut covers PP
147 2 Additional pin screws A4-80
* = For Festo booster 2 x 1172, for SMC and Metal Work 1 x 1171 and 1 x 1172
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 37
5.9. T800 – Spare parts drawing
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 38
5.10. T800 – Spare parts list
Pos. Q-ty Description Material KIT
LIQ
KIT
AIR
KIT
VAL
11 2 Housing PE
12 1 Centre block PP
137-2* 2 In/outlet integrated with DIN flange
PE
137-9 2 In/outlet integrated with ANSI flange
PE
137-12 2 In/outlet integrated with JIS flange
PE
14 8 Pin screw AISI 316
15 2 Diaphragm EPDM, PTFE, NBR x
16 1 Diaphragm shaft AISI 316L x
17 8 Rubber foot NBR
18 4 O-ring set (in/outlet) PTFE/EPDM, EPDM, FKM, NBR, x x
19 2 Spacer sleeve PE x
203 2 Upper sleeve PE, PTFE x
2021 2 Blocking pin PE, PTFE x
213 2 Lower sleeve PE, PTFE x
22 4 Valve ball stop PE1000 x
222 4 Valve seat PE1000 x
23 4 Valve ball EPDM, PTFE, NBR, PU x
25 1 Muffler PP x
26 1 Air intake adapter Galvanized brass
27 1 Circlip Cr3 coated steel
30 6 O-ring NBR (standard), EPDM, FKM
33 2 Plug PE, PTFE
36 2 Centre block seal PE x
37 16 Nut AISI 304
38 16 Washer AISI 304
43 4 O-ring (valve seat) EPDM, PTFE, FKM x
47 2 O-ring (back up for 36) NBR (standard), EPDM, FKM x
57 16 Nut cover PP
61 1 Air valve complete Body: PET*, brass; Piston: PET*, brass;
O-rings: NBR, FKM x
721-9 2 In/outlet integrated with ANSI flange
PE
Diaphragm stroke sensor
1221 1 Centre block for stroke sensor
PP
43 1 O-ring NBR, FKM,
EPDM
74 1 Inductive sensor CuZn
75 1 Sensor cap PP
76 1 Sensing plate AISI 316L
750 1 Cable gland PP
* = Standard
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 39
5.11. Stocking recommendation
Even at normal operation some details in the pump will be worn. In order to avoid
expensive breakdowns we recommend having a few spare parts in stock.
Depending on the severity of the operation and the importance of assuring continuous
work we offer three different spare part KITS – KIT LIQ and KIT VAL includes parts on
pump wetted side, KIT AIR includes parts on the pump air side and that are subject to
wear.
TR9 and TR20:
Pos. Description Q-ty
KIT LIQ
15 Diaphragm 2
18 O-ring set in/outlet 4
20 Lower rod 2
21 Upper rod 2
22 Pin 2
Pos. Description Q-ty
KIT AIR
18 O-ring set in/outlet 4
61 Air valve complete 1
25 Muffler 1
T50, T100, T200, T400 and T800:
Pos. Description Q-ty
KIT AIR
18 O-ring set in/outlet 4
61 Air valve complete 1
16 Diaphragm shaft 1
36 Centre block seal 2
47 O-ring(back up for 36) 2/4*
25 Muffler 1
Pos. Description Q-ty
KIT LIQ
15 Diaphragm 2
18 O-ring set in/outlet 4
23 Valve ball 4
43 O-ring (valve seat) 4
Pos. Description Q-ty
KIT VAL
19 Spacer sleeve 2
2021 Blocking pin 2
202 Upper sleeve 2
212 Lower sleeve 2
222 Valve seat 4
22 Valve ball stop 4
* For T100 pump
5. SPARE PARTS
IOM manual Tapflo PE & PTFE series 40
5.12. How to order parts
When ordering spare parts for Tapflo pumps, please let us know what is the model
number and serial number from the pump centre body or housing. Then just indicate
the part numbers from the spare parts list and quantity of each item.
5.13. Pump code
The model number on the pump and on the front page of this instruction manual tells the
pump size and materials of the pump.
I. Tapflo diaphragm pump IV. Material of wetted parts
II. Basic options V. Material of diaphragms
III. Max capacity [l/min] VI. Material of valve balls
VII. Special executions
T F 100 P T T -7PV
I. T = Tapflo diaphragm pump
II. Basic options:
B = Backup diaphragm pump
D = Drum pump
F = Filter-press pump
K = Pump with built-on dampener (TR20 – T100)
L = Draining system
Q = Special sealed pump
R = Rod valve pump (instead of balls)
T = Twin inlet/outlet pump
V = AISI316 valve seats / spacer
X = ATEX approved, group II, cat. 2
Y = High lift valve seats
Z = Semiconductor industry pump
IV. Material of wetted parts:
P = PE
T = PTFE
L = PP
V. Material of diaphragms:
E = EPDM
W = White (food grade) EPDM
N = NBR (nitrile rubber)
T = PTFE
Z = PTFE with white back (food grade)
B = PTFE TFM 1705b
V = FKM (TR9 – T50 only)
VI. Material of valve balls:
E = EPDM
N = NBR (nitrile rubber)
T = PTFE
S = AISI 316 stainless steel
U = PU (polyurethane)
K = Ceramic
V = FKM
B = PTFE TFM 1635
Material of rod valves (TR9 and TR20 only):
T = PTFE
VII.Special executions:
1 = Optional in/outlet material
2 = Valve seat insert
3 = Optional connection type
4 = Backup diaphragm system configuration
5 = Other special executions
6 = Optional material of centre body
7 = Optional material of air valve
8 = Optional material of pos. 18 seals
9 = Optional material of housing pin screws
11 = Housing reinforcement plates
13 = Twin in-/outlet options
14 = Optional pump feet
17 = Plates for pump/dampener assembly
6. DATA
IOM manual Tapflo PE & PTFE series 41
6. DATA
6.1. Capacity curves
The performance curves are based on water at 20°C.Other circumstances might change the
performance. See below how the capacity will change at different viscosities and suction lifts.
Example:
A flow of 30 litre/minute is desired. The discharge pressure is calculated to 25 mWC. We
choose a T50 pump. It requires an air pressure of 6 bar and will consume approximately 0.20
Nm3 of air per minute.
Recommended flow is half of the max flow, e.g. recommended flow for a T50 is 25 l/min.
6. DATA
IOM manual Tapflo PE & PTFE series 42
6.2. Capacity changes
Capacity changes at different suction lifts Capacity changes at different viscosities
6.3. Technical data
TECHNICAL DATA PUMP SIZE
TR9 TR20 T50 T100 T200 T400 T800
Max capacity* [l/min] / [US GPM] 11 / 2.9 24 / 6.3 60 / 15.8 125 / 33 330 / 87 570 / 150 820 / 216
Volume per stroke** [ml] / [cu in] 13 / 0.80 50 / 3.05 87.5 / 5.34 280 / 17.1 933 / 56.9 2300 / 140.3 5125 / 312.7
Max discharge pressure [bar] / [psi] 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116
Max air pressure [bar] / [psi] 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116 8 / 116
Max suction lift dry*** [m] / [Ft] 1.6 / 5.25 2.4 / 7.87 4 / 13 3.5 / 11 4 / 13 4 / 13 5 / 16
Max suction lift wet [m] / [Ft] 8 / 26 8 / 26 9 / 29.5 9 / 29.5 9 / 29.5 9 / 29.5 9 / 29.5
Max size of solids ø in [mm] / [in] 2 / 0.08 3 / 0.12 4 / 0.16 6 / 0.24 10 / 0.39 15 / 0.59 15 / 0.59
Max temp. pump in PE [°C] / [°F] 70 / 158 70 / 158 70 / 158 70 / 158 70 / 158 70 / 158 70 / 158
Max temp. pump in PTFE [°C] / [°F] 100 / 212 100 / 212 100 / 212 100 / 212 100 / 212 100 / 212 -
Weight of pump in PE [kg] / [lb] 0.75 / 1.65 1.6 / 3.53 4.3 / 9.48 10 / 22 25 / 55.12 47 / 103.62 147 / 342
Weight of pump in PTFE [kg] / [lb] 1.35 / 2.98 3.15 / 6.94 9 / 19.84 17 / 38 47 / 103.62 87 / 191,80 -
Weight of drum pump in PE [kg] / [lb] - 2.4 / 5.29 4.7 / 10.36 10.5 / 23.15 - - -
Weight of drum pump in PTFE
[kg]/[lb]
- 3.9 / 8,6 9.4 / 20.72 17.5 / 38.58 - - -
* = Recommended flow is half of the max flow, i.e. recommended flow for a T50 is 30 l/min (7.9 US GPM)
** = Based on pumps with EPDM diaphragms. Pumps with PTFE diaphragms have about 15% less volume.
*** = With stainless steel valve balls, other materials may reduce suction. Please consult us in this matter.
COMPONENT MATERIAL
Pump housing and all wetted
thermoplastic elements PE, PTFE (apart form T800)
Centre block (not wetted) PP, PP conductive
Diaphragms PTFE, PTFE with white back, EPDM, white EPDM, NBR, FKM*
Valve balls PTFE, EPDM, NBR, AISI 316**, PU, Ceramic**
Rod valves (TR9 and TR20) PE, PTFE
Air valve Body: brass (std.), stainless steel AISI 316L or PET
O-rings: NBR (std.), EPDM or FKM
O-rings (wetted) PTFE, EPDM, FKM, FEP/Silicone, FEP/FKM
Housing pin screws Stainless steel AISI 316L
Diaphragm shaft Stainless steel AISI 316L (TR9, TR20, T800) / 304L (T50 – T400)
Drum handle (TD pumps) Stainless steel AISI 316L
Reinforcement plates (TF pumps) Stainless steel AISI 316L
* = TR9, TR20 and T50 only
** = Not available for T800
6. DATA
IOM manual Tapflo PE & PTFE series 43
6.4. Dimensions
Dimensions in mm (where other is not indicated)
Dimensions in inch (where other is not indicated)
General dimensions only, ask us for detailed drawings. Changes reserved without notice.
Dim PUMP SIZE
TR9 TR20 T50 T100 T200 T400 T800
A 70 105 150 200 270 350 460
2.76 4.13 5.91 7.87 10.63 13.78 18.11
A2 - - 150 300 300 404 -
- - 5.91 11.81 11.81 15.91 -
B 94 112 169 214 310 380 589
3.70 4.41 6.30 8.43 12.20 14.96 23.19
B2 - - 168 221 320 390 -
- - 6.61 8.70 12.60 15.35 -
B3 - - 277 391 490 598 -
- - 10.91 15.39 19.29 23.54 -
B4 134 152 200 254 350 420 -
5.28 5.98 7.87 10.00 13.78 16.54 -
C 115 135 190 250 345 425 637
4.53 5.31 7.48 9.84 13.58 16.73 25.08
D 123 168 243 320 450 563 830
4.84 6.61 9.57 12.60 17.72 22.17 32.68
D2 - 175 250 325 - - -
- 6.89 9.84 12.80 - - -
D3 - - 385 550 700 770 -
- - 15.16 21.65 27.56 30.31 -
D4 - - 343 477 630 690 -
- - 13.50 18.78 24.80 27.17 -
E 92 132 190 252 345 440 650
3.62 5.20 7.48 9.92 13.58 17.32 25.59
E2 - 147 210 280 - - -
- 5.79 8.27 11.02 - - -
E3 - - 250 333 467 588 -
- - 9.84 13.11 18.39 23.15 -
F 8 8 15 15 30 30 30
0.31 0.31 0.59 0.59 1.18 1.18 1.18
F2 - 15 21 21 - - -
- 0.59 0.83 0.83 - - -
G 9 15 17 30 30 30 -
0.35 0.59 0.67 1.18 1.18 1.18 -
H 10 15 16 30 30 30 -
0.39 0.59 0.63 1.18 1.18 1.18 -
I 12 15 20 28 38 48 80
0.47 0.59 0.79 1.10 1.50 1.89 3.15
J ¼” 3/8” ½” 1” 1 ½” 2” 3”
¼ 3/8 ½ 1 1 ½ 2 3
K M4x20 M4x20 M8x25 M8x25 M8x25 M8x25 M8x25
M4 M4 M8 M8 M8 M8 M8
L 1/8” 1/8” ¼” ¼” ½” ½” ½”
1/8 1/8 ¼ ¼ ½ ½ 1/2
M 15 17 25 38 54 70 95
0.59 0.67 0.98 1.50 2.13 2.76 3.74
N 58 81 115 154 211 268 410
2.28 3.19 4.53 6.06 8.31 10.55 16.14
P 35 52 80 105 143 183 238
1.38 2.05 3.15 4.13 5.63 7.20 9.37
R 0° 0° 15° 15° 0° 0° 0°
0° 0° 15° 15° 0° 0° 0°
S 13 15 21 27 35 42 -
0.51 0.59 0.83 1.06 1.38 1.65 -
ØT - 20 33 33 - - -
- 0.79 1.30 1.30 - - -
U - 1270* 1270* 1270* - - -
- 50.00* 50.00* 50.00* - - -
V - 285 360 400 - - -
- 11.22 14.17 15.57 - - -
* = Any length up to 2000 mm (79”) upon
request
6. DATA
IOM manual Tapflo PE & PTFE series 44
Dim
PUMP SIZE
Integrated flanges Built-on dampener
T50 T100 T200 T400 TR20 T50 T100 T200
B 162 216 314 382 112,5 162 216 310
6.38 8.50 12.36 15.04 4.43 6.38 8.50 12.20
C 185 252 352 427 134 185 252 345
7.28 9.92 13.86 16.81 5.28 7.28 9.92 13.60
D 244 320 450 564 251 350 461 649
9.61 12.60 17.72 22.20 9.88 13.78 18.15 25.60
E 140 204 282 372 158 223 299,5 496
5.51 8.03 11.10 14.65 6.22 8.78 11.79 19.50
F 15 15 30 30 8 15 15 30
0.59 0.59 1.18 1.18 0.31 0.59 0.59 1.20
G 116 140 210 290 75 116 140 210
4.57 5.51 8.27 11.42 2.95 4.57 5.51 8.30
H 130 156 254 322 82,5 130 156 250
5.12 6.14 10.00 12.68 3.25 5.12 6.14 9.80
I 60 67 99,5 112 23 35 43 68
2.36 2.64 3.92 4.41 0.91 1.38 1.69 2.70
J ½” 1” 1½” 2” 3/8” ½” 1” 1 ½”
½ 1 1 ½ 2 3/8 ½ 1 1 ½
K 30 30 40 40 15 30 30 40
1.18 1.18 1.57 1.57 0.59 1.18 1.18 1.60
L ¼” ¼” ½” ½” 1/8” ¼” ¼” ½”
¼ ¼ ½ ½ 1/8 ¼ ¼ ½
M 100 135 150 175 17 25 38 54
3.94 5.31 5.91 6.89 0.67 0.98 1.50 2.10
M2 - - - - 53,5 77,5 101,5 135
- - - - 2.11 3.05 4.00 5.30
N 151 197 241 298 89 151 196,5 241
5.94 7.76 9.49 11.73 3.50 5.94 7.74 9.50
P 180 240 341 389 134 172 236 342
7.09 9.45 13.43 15.31 5.28 6.77 9.29 13.5
R 15° 15° 0° 0° 0° 15° 15° 0°
- - - - - - - -
S 65 85 110 125 - - - -
2,56 3,35 4,33 4,92 - - - -
T M12 M12 M16 M16 - - - -
M12 M12 M16 M16 - - - -
U 30 30 45 45 - - - -
1.18 1.18 1.77 1.77 - - - -
6. DATA
IOM manual Tapflo PE & PTFE series 45
6.5. Tightening torques
The following tightening torques are recommended.
PUMP SIZE MOUNTING TORQUE [Nm]
TR9 4
TR20 5,5
T50 8
T100 16
T200 20
T400 23
T800 30
6.6. Permitted loads on manifolds
We recommend not to exceed the following loads and forces reacting on the manifolds.
TR9
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 20 3,5
Y 20 3,5
Z 20 3,5
TR20
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 27 4,2
Y 27 4,2
Z 27 4,2
T50
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 31 5,3
Y 31 5,3
Z 31 5,3
T100
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 35 6,1
Y 35 6,1
Z 35 6,1
T200
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 43 7,4
Y 43 7,4
Z 43 7,4
T400
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 56 9,6
Y 56 9,6
Z 56 9,6
T800
Direction Load [N]
(inlet/outlet)
Moment of force
(inlet/outlet) [Nm]
X 83 11
Y 83 11
Z 83 11
7. WARRANTY
IOM manual Tapflo PE & PTFE series 46
7. WARRANTY
7.1. Warranty form
Company:
Telephone: Fax:
Address:
Country: Contact Name:
E-mail:
Delivery Date: Date of pump installation:
Pump type:
Serial No (see name plate or stamped on pump housing):
Description of the fault:
The installation:
Liquid:
Temperature [°C]: Viscosity [cPs]: Spec grav. [kg/m3]: pH-value:
Content of particles: %, of max size [mm]:
Flow [l/min]: Duty [h/day]: No of starts per day:
Discharge head [mWC]: Suction head / lift [m]:
Air pressure [bar]: Quality of the air (filter, micron, lubrication):
Other:
Place for sketch of installation:
7. WARRANTY
IOM manual Tapflo PE & PTFE series 47
7.2. Returning parts
When returning parts to Tapflo please follow this procedure:
Consult Tapflo for shipping instructions.
Cleanse or neutralize and rinse the part/pump. Make sure the part/pump is
completely empty from liquid.
Pack the return articles carefully to prevent any damage during transportation.
Goods will not be accepted unless the above procedure has been complied with.
7.3. Warranty
Tapflo warrants products under conditions as stated below for a period of not more than 5
years from installation and not more than 6 years from date of manufacturing.
1. The following terms and conditions apply to the sale of machinery, components and
related services and products, of Tapflo (hereinafter “the products”).
2. Tapflo (the manufacturer) warrants that:
a. its products are free of defects in material, design and workmanship at the time of
original purchase;
b. its products will function in accordance with Tapflo operative manuals; Tapflo does
not guarantee that the product will meet the precise needs of the Customer, except
for those purposes set out in any invitation to render documents or other documents
specifically made available to Tapflo before entering into this agreement;
c. high quality materials are used in the construction of the pumps and that machining
and assembly are carried out to the highest standards.
Except as expressly stated above, Tapflo makes no warranties, express or implied,
concerning the products, including all warranties of fitness for a particular purpose.
3. This warranty shall not be applicable in circumstances other than defects in material,
design, and workmanship. In particular warranty shall not cover the following:
a. Periodic checks, maintenance, repair and replacement of parts due to normal wear
and tear (seals, O-rings, rubber items, diaphragms, air valves etc..);
b. Damage to the product resulting from:
b.1. Tampering with, abuse or misuse, including but not limited to failure to use the
product for its normal purposes as stated at the time of purchase or in accordance
with Tapflo instructions for use and maintenance of the product, or the
installation or improper ventilation or use of the product in a manner inconsistent
with the technical or safety standard in force;
b.2. Repairs performed by non-skilled personnel or use of non-original Tapflo parts;
7. WARRANTY
IOM manual Tapflo PE & PTFE series 48
b.3. Accidents or any cause beyond the control of Tapflo, including but not limited
to lightning, water, fire, earthquake, and public disturbances, etc.;
4. The warrantee shall cover the replacement or repairing of any parts, which is documented
faulty due to construction or assembling, with new or repaired parts free of charges
delivered by Tapflo. Parts subjected to normal tear and wear shall not be covered by the
warranty. Tapflo shall decide as to whether the defective or faulty part shall be replaced
or repaired.
5. The warrantee of the products shall be valid for a period in accordance to the current law
from the date of delivery, under the condition that notice of the alleged defect to the
products or parts thereof be given to Tapflo in written within the mandatory term of 8
days from the discovery. Repair or replacement under the terms of this warranty shall not
give a right to an extension to, or a new commencement of, the period of warranty.
6. Repair or replacement under the terms of this warranty shall not give a right to an
extension to, or a new commencement of, the period of warranty. Repair or replacement
under the terms of this warranty may be fulfilled with functionally equivalent
reconditioned units. Tapflo qualified personnel shall be solely entitled to carry out repair
or replacement of faulty parts after careful examination of the pump. Replaced faulty parts
or components will become the property of Tapflo.
7. The products are built in accordance with standard CE normative and are tested (where
applicable) by Tapflo. Approval and tests by other control authority are for the customer’s
account. The products shall not be considered defective in materials, design or
workmanship if they need to be adapted, changed or adjusted to conform to national or
local technical or safety standards in force in any country other than that for which the
unit was originally designed and manufactured. This warranty shall not reimburse such
adaptations, changes or adjustments, or attempt to do so, whether properly performed
or not, nor any damage resulting from them, nor any adaptation, change or adjustments
to upgrade the products from their normal purpose as described in the products operative
manual without the prior written consent of Tapflo.
8. Installation, including electric and other connections to utility mains according to Tapflo
drawings, is for the cost and responsibility of the customer, unless otherwise agreed in
writing.
9. Tapflo will not be liable on any claim, whether in contact, tort, or otherwise, for any
indirect, special, incidental, or consequential damages, caused to the customer or to third
parties, including loss of profits, arising by any possible infringement of par. 3 above or
by the customer or third parties being in the impossibility of using the products.
Steady the above, Tapflo liability to the customer or third parties from any claim, whether in
contract, tort, or otherwise, shall be limited to the total amount paid by the customer for the
product that caused the damages.
TAPFLO AB
Sweden
Filaregatan 4 | S-442 34 Kungälv
Tel: +46 303 63390
Fax: +46 303 19916
E-mail addresses:
Commercial questions: sales@tapflo.com
Orders: order@tapflo.com
Tech support: support@tapflo.com
Tapflo products and services are available in 75 countries on 6 continents.
Tapflo is represented worldwide by own Tapflo Group Companies and carefully selected distributors assuring highest Tapflo service
quality for our customers’ convenience.
AUSTRALIA | AUSTRIA | AZERBAIJAN | BAHRAIN | BELARUS | BELGIUM | BOSNIA & HERZEGOVINA | BRAZIL | BULGARIA |
CANADA | CHILE | CHINA | COLOMBIA | CROATIA | CZECH REPUBLIC | DENMARK | ECUADOR | EGYPT | ESTONIA | FINLAND |
FRANCE | GREECE | GEORGIA | GERMANY | HONG-KONG | HUNGARY | ICELAND | INDIA | INDONESIA | IRAN | IRELAND | ISRAEL |
ITALY | JAPAN | JORDAN | KAZAKHSTAN | KUWAIT | LATVIA | LIBYA | LITHUANIA | MACEDONIA | MALAYSIA | MEXICO |
MONTENEGRO | MOROCCO | THE NETHERLANDS | NEW ZEALAND | NORWAY | POLAND | PORTUGAL | PHILIPPINES | QATAR |
ROMANIA | RUSSIA | SAUDI ARABIA | SERBIA | SINGAPORE | SLOVAKIA | SLOVENIA | SOUTH AFRICA | SOUTH KOREA | SPAIN |
SUDAN | SWEDEN | SWITZERLAND | SYRIA | TAIWAN | THAILAND | TURKEY | UKRAINE | UNITED ARAB EMIRATES |
UNITED KINGDOM | USA | UZBEKISTAN | VIETNAM
Tapflo Group Companies
Austria
Tapflo Austria
Tel: +43 732 27292910
sales@tapflo.at
Azerbaijan
Tapflo Azerbaijan LLC
Tel: +994 502660799
sales@tapflo.az
Baltic States
Tapflo Latvia
Tel: +371 67472205
sales@tapflo.lv
Belarus
Tapflo Belarus
Tel: +375 17 3934609
sales@tapflo.by
Bulgaria
Tapflo EOOD
Tel: +359 (2) 974 18 54
office@tapflo.org
Canada
Tapflo Canada
Tel: +1 514 813 5754
canada@tapflo.com
Croatia
Tapflo GmbH
Tel: +385 91 4884 666
sales@tapflo.hr
Czech Republic
Tapflo s.r.o.
Tel: +420 513033924
tapflo@tapflo.cz
China
Tapflo (Wuxi)
Tel: +86 510 8241 7602
sales@tapflo.cn
Denmark
Tapflo Danmark
Tel: +45 36 454600
info@tapflo.dk
France
Tapflo France
Tel: +33 1 34 78 82 40
info@tapflo.fr
Georgia
Tapflo Georgia
Tel: +995 577 463010
sales@tapflo.ge
India
Tapflo Fluid Handling India
Pvt Ltd
Tel: +91 20 65000215
ad@tapflo.in
Ireland
Tapflo Ireland Ltd
Tel: +353 1 2011911
info@tapflo.ie
Italy
Tapflo Italia
Tel: +39 0362307698
info@tapfloitalia.com
Japan
Tapflo Japan K.K.
Tel: +81-3-6240-3510
tapflojp@tapflo.co.jp
Kazakhstan
Tapflo Kazakstan
Tel: +7 727 3278347
sales@tapflo.kz
Poland
Tapflo Sp. z o.o.
Tel: +48 58 530 42 00
info@tapflo.pl
Romania
S.C. Tapflo Rom. S.r.l.
Tel: +40 21 3451255
sales@tapflo.ro
Russia
Tapflo Company
Tel: +7 495 232 18 28
sales@tapflo.com.ru
Serbia
Tapflo d.o.o.
Tel: +381 21 44 58 08
sales@tapflo.rs
Slovakia
Tapflo s.r.o.
Tel: +421 911 137 883
tapflo@tapflo.sk
Slovenia
Tapflo GmbH
Tel: +386 68 613 474
sales@tapflo.hr
Spain
Tapflo Iberica
Tel: +34 91 8093182
avives@tapfloiberica.es
South Africa
Tapflo (Pty) Ltd
Tel: +27 31 701 5255
sales@tapflo.co.za
Turkey
Tapflo Makina Ltd
Tel: +90 216 467 33 11
sales@tapflo.com.tr
Ukraine
TOB Tapflo
Tel: +380 44 222 68 44
sales@tapflo.com.ua
Uzbekistan
Tapflo Uzbekistan
Tel.: +998 712340940
sales@tapflo.uz
United Kingdom
Tapflo (UK) Ltd
Tel: +44 2380 252325
sales@tapflopumps.co.uk
top related