paclease hybrid sacagawea vk-1222 display instructions / …€¦ · when disassembling aluminum...
Post on 28-Oct-2020
3 Views
Preview:
TRANSCRIPT
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
10’
10’ Plan View
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 1 - General Layout
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 2 - General Information
The Tool
Some sections of your display will beassembled with the supplied Hex Key Tool.
Typical Connection
Sections that require the Hex Key Tool for assembly are simple to join. Place the tool into the lockscrew and turn counter clockwise to loosen the lock. You will see the lock sections come together.Place the part into the adjoining extrusion groove where it should connect and turn the toolclockwise so the lock spreads apart while inside the groove. This completes a strong connection.
Typical Connection (cont’d)
Each extrusion contains a numbered label whichcorresponds with setup instructions. The label islocated within a groove of the extrusion (when possible).
Numbered Label
Horizontal sections will connect using thepre-installed camlock thumbscrew. Donot over tighten screw.
Vertical sections connect using verticalconnection bars with pre-installed twistknobs. Turn clockwise to tighten. Do notover tighten knobs.
Knob
Knob
Attach base place feet to vertical main supportsusing the bolt provided. The bolt is normallypre-installed into the bottom of the verticalsupport leg. Be careful not to strip the threads.
Using Your Setup Instructions
Cleaning and Packing Your Display
The Visionary Designs Setup Instructions are created specifically for yourconfiguration. They are laid out sequentially, including an exploded view ofthe entire display, and then a logical series of detailed steps to assemble themain structure and components. We encourage you to study the instructionsbefore attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling yourexhibit to prevent loss of the locks and setscrews (see below in RED).This is VERY IMPORTANT.
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.2) When cleaning laminate inserts or countertops, use mild cleansers and a soft material such as cotton.3) Keep all display components away from extreme heat and long exposure to sunlight to avoid warping and fading.4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of shipping damage.
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 3 - Backwall Assembly
Turn Knob Clockwiseto Tighten Lock
STAR indicates location of knobs on BACKSIDE of unit.
**Do not over tighten Knobs.**
Knob
Knob
GREEN STAR indicateslocation of connection
lock with knob.Set upper horizontal bars
[5a/5b] to be flush withindicated line before angled
top cap section
Horizontal Placement
3a
5a
Stopper
Item1232a3a
4a/4b5a/5b
DescriptionBase Plate42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached45”w Horizontal Extrusion45”w Horizontal Extrusion
Qty.21111
1/11/1
Steps:1) Attach vertical extrusions [2] to base plates [1].2) Attach upper vertical extrusions [3 and 3a] to lower extrusions [2 and 2a] using connection bar [b].3) Connect horizontal extrusions [4a to 4b and 5a to 5b] together using connection bars [a].4) Attach horizontal assemblies [4a/4b and 5a/5b] between vertical assemblies as shown.5) Apply graphic via velcro to back of assembled backwall. Pull tight until velcro isn’t visible from front.6) Attach light to top of assembled backwall.
2a
3a
1
4a
1
2
3
5a
4b
5b
ConnectionBar
Slide Connection Barbetween Extrusionsand tighten Knobs
to secure.
ConnectionBar
Graphic AttachmentApply graphic to back
of assembled backwall.
ConnectionBar
a
a
bConnectionBar
b
A10 clam
ps attached to vertical extrusions for Wing A
ttachment
Light ConnectionAttach Lights toBackwall where desired and tighten in place.
A10 clam
ps attached to vertical extrusions for Wing A
ttachment
Stopper
Rear graphics velcro into positionto pre-installed loop velcro strips.
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 4 - Header Assembly
Item789
Description9.2856”h Vertical extrusion9.2856”h Vertical extrusion43.66”w Curved Horizontal Extrusion
Qty.111
Steps:1) Connect curved horizontal extrusion [9] between vertical extrusions [7 and 8].2) Attach assembled header to top of assebled backwall as shown.
**NOTE: Header must stay assembled when shipping
8
9
Lock header frame totop of assembled backwallusing supplied hex tool
Extrusion LockExtrusion Lock
Graphic AttachmentVelcro graphic to BACK ofassembled header frameafter connecting to main unit.Pull graphic tight until velcrois not visible from front.
7
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 5 - Wings/Counter
*Note: Curved extrusion[10] and horizontal [11]must stay assembledwhen shipping.
Item1010a1111a
Description30.2” Curved ExtrusionLeg Support12.184”w Horizontal ExtrusionFlange Plate
Qty.1111
Steps:1) attach assembled counter support [10/11] to vertical where indicated.2) Attach support leg [10a] to counter support [10/11].3) Attach flange plate [11a] to top of curved extrusion [10] as shown.4) Attach counter atop support, see counter top attachment detail.5) Attach wings to clamps as shown.
Counter Top AttachmentInsert screws located on undersideof counter into holes on flange plateand secure with wing nuts.
Wing Nut
Screw
10
11
11a
*
Monitor Mount Attachment V
4 Connectors
Attach monitor mount back plateto connectors using screws provided.
*
10a
Wings connect insidepre-installed clips.Each clip has a thumbscrewthat you tighten on the wing.Do not over tighten.
YOUR DISPLAY CURRENTLYDOES NOT INCLUDE A
MONITOR MOUNT
The literature holder connects toits support arm and to the backwallvertical using the supplied hex tool.You can position these items at any
location you wish. Use all 3 or just 1 or 2.
Top wing should alignwith main back wallhorizontal
Leaving about 3/4”gap between thetwo wings is recommended
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 6 - Forward Counter Part 1
Part NumberABCD
Step 1: A) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.B) Insert Laminated infill into grooves of leg assemblies [A and B].C) Attach extrusion door between leg assemblies [A and B] and atop laminated infill.D) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B], and set flush with top of legs [A and B].
DescriptionLeft Leg AssemblyRight Leg AssemblyHorizontal ExtrusionHoriontal Extrusion w/ Door Stopper
BlackKnob
Turn Knob Clockwiseto Tighten Lock
DOOR
Laminated Infill
A (left)B (right)
C
D (w/ Door Stopper)Knobs face INSIDE
of workstation
Knobs face INSIDEof workstation
Knobs face FORWARD
Pins are located on INSIDEFRONT vertical
of LegAssemblies
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion back and forth while turning knob until lock fully opens.
Align with bottom of leg assemblies [A and B].
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 7 - Forward Counter Part 2
Part NumberEF
Step 2: A) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.B) Insert Laminated infill into grooves of vertical leg assemblies [A and B].C) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill. D) Place internal shelf into assembled pedestal atop pins..E) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top.
DescriptionHorizontal ExtrusionHorizontal Extrusion
E
LaminatedInfill
Knobs facing FORWARD
Place internal shelf into workstation then
place counter atopassembled workstation.
InternalShelf
F
Knobs face INSIDEof workstation
Bottom of counter has velcrostrip to fasten to main body fora more secure fit.
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 8 - Packing Part 1
Setup Hardware
Lights
Graphic
Case #1 Backwall Components
CounterTop
Base Plates
Backwall CounterSupport
Level 1 Level 2 Level 3
Wing PanelsA
ssem
bled
Hea
der a3
&3# snoi surt xE
a2&2# snoi surt x
E
Hor
izon
tal e
xtru
sion
s #4
a&4b
abd
5a&
5b
10a
Con
nect
ion
Bar
s A
Con
nect
ion
Bar
s B
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052
PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 9 - Packing Part 2
Level 1Level 2Level 3Level 4Level 5
Top View of each Level
Case #2 - Workstation Components
Counter
InternalShelf
Inserts
Door
Leg AssemblyB
Leg AssemblyA
Horiz. Extrusion E Horiz. Extrusion F
Hor
iz. E
xtru
sion
D
Hor
iz. E
xtru
sion
C
Con
nect
ion
Bar
for V
ertic
als
top related