muto comfort self-closing xl 120 - dormaproducts.dorma.com/content/download/41883/473925/936013...
Post on 23-Mar-2018
225 Views
Preview:
TRANSCRIPT
Installation instructions -
Ceiling mount with DORMOTION and Self-Close (Glass door)
MUTO COMFORT SELF-CLOSING
XL 120
—
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
TABLE OF CONTENTS—
Closer overallOverview Intended use
Wall/ceiling requirements and fi ttings
Requirements for glass panel
Safety instructions
Symbols used - safety/ installation
Maintenance, care, repair
Disposal 3
Specifi cations
Technical data 3
Tempered laminate glass and adhesive specifi cations 4
Installation Instructions
Overall view 5
Securing track to mounting surface 6
Single door mount
Double door mount 7
Installing the roller carriers: on monolithic glass ONLY 8
Installing the roller carriers: on tempered laminate glass ONLY 9
ANTI-JUMP:
Disengaging the anti-jump 10
Engaging the anti-jump 12
DORMOTION Unit:
Installing DORMOTION: on monolithic glass ONLY 8
Installing DORMOTION: on tempered laminate glass ONLY 9
Installing DORMOTION start/stops 14
END STOPS:
Installing end stops 10
Adjustment end stop location: LEADING end stop
Adjustment end stop location: TRAILING end stop 13
FLOOR GUIDE:
Installing fl oor guide 11-12
Installing glass/rollers on track 11
Installing cover clips
Installing brush profi le
Installing cover
Installing end caps 18
SELF-CLOSE UNIT:
Install self-close hold open clamp
Install self-close hold open ball
Install self-close cable connector 15
Install self-close cable unit
Prepare self-close cable unit 16
ADJUSTMENTS:
Adjustment door height 12
Adjustment end stop location: LEADING end stop
Adjustment end stop location: TRAILING end stop 13
Adjust tension in self-close cable unit 17
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
3
Symbols used – Safety/Installation
Caution! Mounting components must meet the requirements of
substructure/wall and door weight. Please read the
technical information for fittings.
Risk of breaking glass When installing the door, support the door panel with
a block of wood or similar object.
Information note
Always use silicone- and oil-free cleaners
(e.g. acetone).
Closing edge
Maintenance, care, repair
- immediately replace damaged parts
- always use original DORMA parts
- use a damp cloth for occasional cleaning, especially the
track
Disposal
Dispose in accordance with local, state and national
regulations.
OverviewThese instructions are for installation of the MUTO COMFORT
sliding door system XL120 for the following mounting and
style versions:
1. Ceiling mounting
Intended use
- for sliding doors in dry indoor areas only
- for manual slow opening and closing only
Wall/Ceiling requirements and fittings
- The substructure/wall must be able to bear permanent loads,
be level and perpendicular (max. tolerance: 1/16" (2 mm) per
meter non-cumulative).
- Fixings must be sufficiently dimensioned for the substructure/
wall and weight of the door.
Requirements for glass panel
- Heat-soaked thermally tempered safety glass
- Clamping area must be level and uncoated
(no self-cleaning coating!)
Safety instructions
- Installation requires two people
- Always wear protective clothing
Single door Double door
XL120 XL120
CeilingMount
Max. door leaf width
inches [mm]
57"
[1448]
2x 57"
[2x 1448]
Min. door leaf width
inches [mm]
33-1/2"
[850]
2x 33-1/2"
[2x 850]
Max. door height
inches [mm]
118"
[3M]
118"
[3M]
Door leaf thickness inches
[mm]
5/16" - 1/2"
[8-13]
5/16" - 1/2"
[8-13]
Door leaf weight lbs [kg]≤ 264lbs
[≤ 120]
≤ 264lbs
[≤ 120]
Technical data
Specifications
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
4
Required parts for laminate glass with MUTO System (not included)
Color Part Number Quantity Usage recommendation
3M™ Scotch-Weld™ Urethane Adhesive,
DP 605 NS
off white 934.800 1 tube 1 tube per 4 roller
carriers
3M™ Scotch-Weld™ EPX™ Plus II
Applicator with 2:1 and 1:1 Plunger 2
934.801 1 applicator
3M™ Scotch-Weld™ EPX™ Plus II
Mixing Square Nozzle, 5.3mm 3gold 934.805 1 nozzle 4 nozzles per 1 tube of
adhesive
MUTO TLG gasket set 836.468 1 set
Handling time frame Function Time
Working life (time between application and clamping of carrier)
5 minutes @ 75°F
Handling strength 20 minutes @ 73°F or more
Full cure time (time until glass may be completely installed into door)
48 hours @ 73°F or more
NOTE: Door glass should not installed until the full cure time as been reached (see chart above).
2 Scotch-Weld™ EPX™ Plus II Applicator with 2:1 and 1:1 Plunger is a trademark of 3M.
3 Scotch-Weld™ EPX™ Plus II Mixing Square Nozzle is a trademark of 3M.
Important safety-related information for the mounting and use of DORMA glass hardware.
(Follow these instructions in addition to the mounting and operating instructions in order to avoid damage of product and damage to person or property.)
Important: This document is intended to inform users of safety-related information and the mounting and operation instructions.
General information
1. DORMA requires use of tempered laminated glass.
2. DORMA glass hardware is not suitable for application in
rooms where chemicals (e.g. chlorine) are used as indoor
swimming pools, saunas or salt-water pools.
3. Never move sliding panels faster than walking speed
and always stop the door manually before it reaches end
position.
4. Do not swing doors with excessive force. Install limiting
stop to prevent door from opening too far.
Mounting
1. Only properly qualified and specially trained staff is
authorized to mount DORMA glass hardware.
2. Never use glass with conchoidal fractures and/or
damaged edges.
3. Due to crushing hazards and possible injury caused
by breakage of glass during mounting, corresponding
protective clothing (especially gloves and protective
goggles) is required.
4. Clean clamping area with alcohol-based standard
commercial cleaning agent before mounting the glass
hardware.
5. Never clamp metal glass fitting hardware directly to glass
surface.
6. Never use clamping roller carriers on self-cleaning
coatings.
7. When adjusting glass elements, always stick to the
required clearance for the respective hardware. Adjust
clearance so glass does not come in contact with any
hard surfaces such as glass, metal or concrete.
8. Do not use excessive force when installing the glass
(avoid over tightening screws).
Maintenance Check glass hardware at regular intervals for proper
positioning and smooth operation and correct
adjustment. High traffic door systems require inspection
by properly qualified staff (specialized companies or
installation firms). Immediately replace damaged glass
elements (no glass flaking and/or conchoidal fractures)!
Only use suitable cleaning and care products to clean
the surfaces.
Tempered laminate glass and adhesive specifications
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
5
1
98
7432
410
67
Syst
em in
clud
es t
he f
ollo
win
g co
mpo
nent
s:
1.
Cove
r panel
2.
Bru
sh s
trip
3.
Tra
ck
4.
End c
ap
5.
End s
top
6.
Self
-clo
se h
old
open c
lam
p
Ove
rall
view
7.
Cove
r clips
8.
Sta
rt/s
top g
uid
e
9.
Roller
carr
ier
10
. Flo
or
guid
e
11
. D
orm
oti
on u
nit
12
. S
elf
-clo
se h
old
open b
all
11
13
. S
elf
-clo
se c
able
connecto
r
14
. S
elf
-clo
se c
able
unit
INSTALLATION INSTRUCTIONS
55
912
13
14
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
6
Securing track to mounting surface
NOTE: OVERHEAD REINFORCEMENT:The overhead reinforcement must be a minimum of ¼” (6mm) x 3” (76mm) steel angle, 16 gauge metal stud, or two pieces of 1 1/2” (38mm) thick wood blocking (double stacked), secured to studs or joists on a maximum 16” (406mm) centers for the length of the track. The overhead reinforcement may be flush on the overhead surface or on the interior of this surface.
Track mounting screws must fully penetrate the steel angle, metal stud, or at a minimum of 2” (51mm) into wood blocking, utilizing the predrilled holes in the MUTO track.
Consult with a structural engineer to determine if reinforcement is adequate for your specific application or to meet specific codes in your location.
1.1 Ensure the track is properly level and secure it to
the ceiling per the appropriate measurements on the
following page.
NOTE: SEE DIMENSION INSTRUCTIONS ON NEXT PAGE FOR REFERENCE.
1.2 Use appropriate fasteners according to the following
recommendations.
1
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
7
Single door mount
Double door mount
1-3/16"
[30mm]
Track length = 2 x DW
1-3/16"
[30mm]
clear opening
height (CH)
clear opening
width (CW)
Glass
door
DH Glass door height clear opening height + 7/8" [22mm]
TH Floor to top of track door height + 1-7/8" [47mm]
DW Glass door width clear opening width + 2-3/8" [60mm]
DH
TH
= D
H +
1-7
/8"
[47
]
3/8"[10mm]
Bottom of
glass to floor
Back of track
to center of
mounting
hole in track
7/8"
[23mm]
clear
opening
height
(CH)
clear opening
height (CH)
clear
opening
width
(CW)
1-3/16"
[30mm]
1-3/16"
[30mm]
1/4"
[6mm]
Overall track length = (D1TL + D2TL) + 1/4 " [6mm]
Door1 Track length (D1TL) =
2 x DW
Door2 Track length (D2TL) =
2 x DW
Glass
door
DH Glass door height clear opening height + 7/8" [22mm]
TH Floor to top of track door height + 1-7/8" [47mm]
DW Glass door width clear opening width + 2-3/8" [60mm]
DH
TH
= D
H +
1-7
/8"
[47
]
3/8"[10mm]
Bottom of
glass to floor
Back of track
to center of
mounting
hole in track
7/8"
[23mm]
clear
opening
height
(CH)
DW
DW DW
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
8
Installing the roller carriers: on monolithic glass ONLY
NOTE: FULLY CLEAN SURFACE OF GLASS WITH AN ALCOHOL-BASED MILD GLASS AND SURFACE CLEANER. INSURE NO DEBRIS IS ON THE GASKET.
Hex key size:
XL120 = 4mm
Glass
gasket
(Back of) Glass2
Roller location on glass with DORMOTION unit
XL120
Single door X 2-3/8" [60]
Single door Z 3-1/8" [80]
Double door X 2-3/8" [60]
Double door Z 3-1/8" [80]
Z
X
2.1 Slide LEADING roller carriers onto glass.
2.2 Slide glass gasket and metal shim between glass and
roller carrier.
NOTE: Orient gasket with rubber side facing the glass.
2.3 Secure LEADING roller carrier to glass using appropriate-
size hex key at 10ft lbs (14 Nm).
2.4 Secure TRAILING roller carrier to glass following steps
2.1 - 2.3 on this page.
Legend: leading edge
of glass
3.1 Slide DORMOTION dampener onto glass.
NOTE: Oriented with triggers facing outward.3.2 Dampener must be flush against leading roller carrier.
NOTE: Leading carrier is on side of glass closest to latch.
3.3 Secure dampener to glass using appropriate-size hex key
at 2.2 ft lbs (3Nm).
3.4 Insure DORMOTION triggers are engaged by pushing
them out towards the end of the DORMOTION unit.
3
Installing DORMOTION: on monolithic glass ONLY
XL120
Trigger
Hex key size:
XL120 = 4mm
Legend: leading edge
of glass
DETERMINE THE LEADING (X) VERSUS TRAILING (Z) EDGE OF THE GLASS. "LEADING IS SIDE CLOSEST TO LATCH (CLOSED)."
Roller
carrier
(Back of) Glass
Secure
DORMOTION
dampener
Roller
carrier
DORMOTION dampener flush against LEADING
roller carrier
Secure
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
9
NOTE: THE RECOMMENDED ADHESIVE'S SET-UP TIME IS 20 MINUTES FOR THE DUO-PAK CARTRIDGES.
NOTE: FULLY CLEAN SURFACE OF GLASS WITH AN ALCOHOL-BASED MILD GLASS AND SURFACE CLEANER. INSURE NO DEBRIS IS ON THE GASKET.
2.1 Slide LEADING carrier onto glass.
2.2 Slide laminated glass gasket and metal shim between
glass and roller carrier.
NOTE: Orient gasket with rubber side facing the glass.
2.3 Tighten vented set screws using a torque wrench with
4 ft-lbs (5Nm).
NOTE: Onto scrap material, first dispense approximately 12" of 3M™ Scotch-Weld™ Urethane Adhesive prior to application to prevent mixing errors and ensure optimal hardening.
2.4 Dispense adhesive into vented set screws on both sides
of carrier.
Stop application when adhesive can be seen past edge of roller carrier.
DO NOT WIPE any excess adhesive from glass surface. Allow adhesive to dry and scrape off glass surface with a beveled-edge chisel or putty knife.
Again, stop application when the adhesive begins to press out of ends of roller carrier.
2.5 Keep glass flat during curing process.
2.6 See chart in Specifications section for appropriate curing
time.
2.7 Secure TRAILING roller carrier to glass following steps
2.1 - 2.6 on this page.
Installing the roller carriers: on tempered laminate glass ONLY
Roller
carrier
Glass
gasket
Ventedset screws
3M™ Scotch-
Weld™ EPX™ Plus
II Applicator
Stop when adhesive can be seen past end
of roller carrier2
3.1 Slide DORMOTION dampener onto glass.
NOTE: Oriented with triggers facing outward.3.2 Dampener must be flush against leading roller carrier.
NOTE: Leading carrier is on side of glass closest to latch.
3.3 Secure dampener to glass using appropriate-size hex key
at 2.2 ft lbs (3Nm).
3.4 Ensure DORMOTION triggers are engaged by pushing
them out towards the end of the DORMOTION unit.
3
Installing DORMOTION: on tempered laminate glass ONLY
XL120
Trigger
Hex key size:
XL120 = 4mm
ZX
Roller location on glass with DORMOTION unit
XL120 XL120
Single door X 2-3/8" [60] Z 3-1/8" [80]
Double door X 2-3/8" [60] Z 3-1/8" [80]
DETERMINE THE LEADING (X) VERSUS TRAILING (Z) EDGE OF THE GLASS. "LEADING IS SIDE CLOSEST TO LATCH (CLOSED)."
Legend: leading edge
of glass
(Front of) Glass(Back of) Glass(Back of) Glass
DORMOTION
dampenerRoller
carrier
DORMOTION dampener flush against LEADING
roller carrier
Legend: leading edge
of glass
Hex key size:
XL120 = 4mm
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
10
4.1 Disengage the anti-jump on roller carrier. NOTE: Using an appropriate-size hex key, push anti-jump adjustment screw IN and turn COUNTER-CLOCKWISE to disengage anti-jump.
4
Anti-jump
adjustment
screw
Anti-
jump
Anti-
jump
Disengaging the anti-jump
NOTE: Anti-jump shipped engaged.
Hex key size:
XL20 = 4mm
Handing the [opening side] end stop:5.1 Determine closing edge of door.
Self-close end stop will be used on opening side of door.
5.2 Hand self-close end stop by inserting bumper on
appropriate side of end stop.
Install both end stops:5.3 Slide self-close end stop into opening side of track.
5.4 Slide appropriate standard end stop into closing side of
track.
NOTE: Loosen bottom section of end stop for easier install.NOTE: Be sure set screw is flush with back of bumper.NOTE: Exact location/adjustments will be determined in step 11.
5
Track
End stops
Set
screw
Installing the end stops
Hex key size:
XL120 = 3mm
Legend: closing/leading
edge of glassHanding self-close end stop
Standard end stop Standard end stopSelf-close end stop Self-close end stop
Slide open to the right: RIGHT hand
Slide open to the left: LEFT hand
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
11
INSURE ROLLERS AND TRACK ARE FREE OF DEBRIS.
6.1 Place glass on setting blocks on floor for stability. 6.2 Tip glass and rollers upward and rest rollers on track.
6
Setting block
locations
7.1 Align centerline of glass with centerline of floor guide.
7.2 Be sure the glass is plumb.
NOTE: Center of floor guide should be 13/16" [20mm] off edge of the wall.
7.3 Mark appropriate floor guide measurements and remove
glass and rollers from track.
7.4 Pre-drill into mounting surface using a 5/16" drill bit.
7.5 Secure floor guide anchor with included fasteners.
7
Glass
Install floor guide
Glass
X
Floor
guide
XL120
X13/16"
[20mm]
1-7/16"
[36 mm]
13/16"
[20 mm]
Floor
guide
anchor
Install glass/rollers in track
Rollers
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
12
9.1 Set height of glass door.
9.2 Using appropriate-size hex key, loosen height adjustment
locking screws of carrier.
9.3 Using appropriate-size hex key, turn height adjustment
screw CLOCKWISE or COUNTER-CLOCKWISE to raise or
lower glass.
NOTE: Be sure glass is level during this adjustment.
9
Height
adjustment
locking screwsXL120 torque
10 ft lbs
[14 Nm]
Height
adjustment
screw
10.1 Engage anti-jump on roller carrier. NOTE: Using appropriate-size hex key, push anti-jump adjustment screw IN and turn CLOCKWISE to engage anti-jump.
10
Anti-
jump
Anti-jump
adjustment
screw
Anti-
jump
Engaging the anti-jump
Door height adjustment tolerance
XL120
+3/16" [+5]
-3/16" [-5]
Glass
Floor
guide 3/8"
[10mm]
8.1 Set glass and rollers onto track.
8.2 Slide floor guide over floor guide anchor and tighten with
set screws.
8.3 Remove setting blocks.
NOTE: Be sure glass is centered in floor guide.
8
Floor
guide
Floor
guide
anchor
Glass
Install floor guide: continued
Set screws
Adjustment door height
= =
Hex key size:
XL120 = 1.5mm
Hex key size:
XL120 = 4mm
Hex key size:
XL120 = 4mm
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
13
Set end stop locations:11.1 Slide end stop to
desired location
on track. Bumper
should touch edge
of roller carrier.
11
Adjustment end stop location: LEADING end stop
Door opened
End
stop
Hex key size:
XL120 = 3mm
Door closed
LOCATION OF GLASS DOOR
TO FRAMEEDGE
END STOP LOCATION:LEADING EDGE
Handle to frame edge distance.*Verify with local jurisdiction.*
Glass
Handle
Frame
edge
Glass
edge
max. 1-3/16"
[30mm]
Glass overlap of door frame
min. 1"
[25mm]
Handle
Frame
edgeGlass
edge
min. 1"
[25mm]
NOTE: Pair of doors: Be sure there is a 1/4" [6mm] gap between the two doors.
Bumper
Secure
XL120torque
3 ft lbs
[4 Nm]
Adjustment end stop location: TRAILING end stop
END STOP LOCATION:TRAILING EDGE
LOCATION OF GLASS DOOR
TO FRAMEEDGE
Set end stop locations:11.2 Slide end stop to
desired location
on track. Bumper
should touch edge
of roller carrier.
Hex key size:
XL120 = 3mm
NOTE: Pair of doors: Be sure there is a 1/4" [6mm] gap between the two doors.
Handle to frame edge distance.*Verify with local jurisdiction.*
Glass
BumperEdge of roller
carrier
0mm
End
stop
0mm
Bumper Edge of roller
carrier
11
XL120torque
3 ft lbs
[4 Nm]
Bumper
Secure
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
14
12.1 Loosen screws on plates. NOTE: Plates should start out parallel to track.
12.2 Place start/stop into track channel.
12.3 (SEE STEPS 12.3 - 12.7 INSIDE IMAGE ABOVE.)
12
Install DORMOTION start/stops
Trigger
Legend: leading edge
of glass
Plates parallel Plates parallel
Rotate in
track
Set
screw(s)
Hex key size:
XL120= 4mm
End
stop
End
stop
Start/
stop
RollerDORMOTION
UNIT
Roller
End
stop
0mm
Bumper
Edge of roller
carrier
Slide trigger in toward middle of
Dormotion unit.
Start/stop
12.3 Slide door all the way OPEN.
12.4 Carrier should touch end stop.
12.5 Slide start/stop into
Dormotion unit.
12.6 Rotate plates inside track to
engage.
12.7 Tighten screws using
appropriate-size hex key.
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
15
Install self-close hold open clamp
Self-close unit
13.1 Secure self-close hold open clamp to the end stop
furthest from latch [closing side].
Use two screws and tighten to 2.5 ft lbs (3Nm).
13
Self-close
hold open
clamp
End stopHex key size:
XL120 = 4mm
Legend: leading edge
of glass
Install self-close hold open ball
14.1 Secure self-close hold open ball to carrier furthest from
latch [closing side].
Use two screws and tighten at 2.5 ft lbs [3Nm].
Install self-close cable connector
15.1 Secure self-close cable connector to opposite end of
carrier, furthest from latch [closing side].
Use two screws and tighten at 2.5 ft lbs (3Nm).
Hex key size:
XL120 = 4mm
Self-close
hold open
ball
Hex key size:
XL120 = 4mm
Self-close cable
connector
14
15
Legend: leading edge
of glass
Legend: leading
edge
of
glass
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
16
17.1 Pull "end of cable" over to connect with cable connector. 17.2 Continue to pull cable through connector to either
increase or decrease self-closing tension.
17
Prepare self-close cable unit
Self-close
cable unit
Self-close
cable
connector
End of
cable
Beginning
of cable
End of
cable
NOTE: CABLE UNIT COVER HIDDEN FOR BETTER VIEWING OF CABLE.
Install self-close cable unit
16.1 Secure self-close cable unit into first groove of MUTO
track.
16.2 Rotate plates inside track channel to engage.
Use three screws/plates and tighten at 3 ft lbs (4 Nm).
16
Self-close
cable unit
Cable unit
plates
4"
[100]
Self-close
cable unit
TrackEnd stop
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
17
v = max. 0,2 m/Sek
200...
...
18
Adjust tension in self-close cable unit
18.1 To adjust tension in cable unit cord if necessary, pull
'beginning knot of cable' through cable holder.
18.2 Secure another 'knot' and pull cable through holder as
show in image above.
18.3 Secure beginning 'knot' in holder clamp.
NOTE: Be sure there is a 7-7/8" [200mm] gap between each new 'knot' in the cord.
v = max. 0.2 m/sec
7-7/8" [200]
Beginning
knot of cable
Cable
holderSecond
'knot'
Holder clamp
DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 Website: www.dorma.com
936013 11/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice
MUTO COMFORT XL120 SC (SELF-CLOSE) - CE MOUNT—
18
22.1 Snap end caps onto track.
22
End
cap
End
cap
Install end caps
21.1 Secure cover to clips and snap into place.
21Cover
NOTE: Roll cover from the bottom upwards. Ensure the bottom of the cover is supported by the groove in the cover clip.
Cover
Cover
clip
Install cover
20.1 Measure and cut brush to appropriate length.
20
Install brush profile
20.2 Slide brush into cover.
19.1 Insert cover clips into track. (One clip per foot) 19.2 Insert perpendicular to track, and turn CLOCKWISE to
snap into place.
19
Cover clip
Brush
Cover
Install cover clips
93
6013
11
/2016
, S
ubje
ct
to c
hange w
ithout
notice
DORMA USA, INC.
DORMA DRIVE, DRAWER AC
REAMSTOWN, PA 17567
TOLL-FREE: 800-523-8483
FAX: 800-274-9724
WEBSITE: WWW.DORMA.COM
top related