model f50 downflow
Post on 15-Nov-2021
15 Views
Preview:
TRANSCRIPT
MODEL F50 DownflowService Manual
IMPORTANT: Fill in pertinent information on page 2 for future reference.
MODEL F50
Page 2
* JOB NO.
Job Specification Sheet
* MODEL NO.
* WATER TEST
* CAPACITY PER UNIT MAX. PER REGENERATION
* MINERAL TANK SIZE DIA. HEIGHT
* BRINE TANK SIZE & SALT SETTING PER REGENERATION:
* F50 CONTROL VALVE SPECIFICATIONS
1 Type of Timer (see pages 16-19)
2 Timer Program Settings (see page 15)
A) Backwash min.
B) Brine & Slow Rinse min.
C) Rapid Rinse min.
D) Brine Tank Refill min.
3 Drain Line Flow Controller gpm
4 Brine Line Flow Controller gpm
5 lnjector Size #
6 A) Hard Water By-Pass
B) No Hard Water By-Pass
A) 7 day or 12 day
B) * 1,250 to 21,250 gallon meter or
* 6,250 to 106,250 gallon meter
* Other
C) Meter Wiring Package
1) System #4 - 1 tank; 1 meter; immediate or delayed regeneration
2) System #5 - 2 tanks; 2 meters; interlock
3) System #6 - 2 tanks; 1 meter; series regeneration
4) System #7 - 2 tanks; 1 meter; alternator
MODEL F50
Page 2
* JOB NO.
1. Place the softener tank where you want to install the unit making sure the unit is level and on a firm base.
(Maximum 4 feet apart for twin units.)
2. All plumbing should be done in accordance with Iocal plumbing codes. The pipe size for the drain Iine
should be the same size as the drain Iine flow control female connection. Water meters are to be installed
on soft water outlets. Twin units with (1) one meter shall be installed on common soft water outlet of units.
3. Solder joints near the drain must be done prior to connecting the Drain Line Flow Control fitting. Leave at
Ieast 6“ between the DLFC and solder joints when soldering when the pipes are connected on the DLFC.
Failure to do this could cause interior damage to the DLFC.
4. Teflon tape is the only sealant to be used on the drain fitting. The drain from twin units may be run
through a common Iine.
5. Make sure that the floor is clean beneath the salt storage tank and that it is Ievel.
6. Place approximately 1”of water above the grid plate (if used) in your salt tank. Salt may be pIaced in the
unit at this time.
7. On units with a by-pass, place in by-pass position. Turn on the main water supply. Open a cold soft water
tap nearby and Iet run a few minutes or until the system is free from foreign material (usually solder) that
may have resulted from the installation.
8. Place the by-pass in service position.
9. Manually index the softener control into “service” position and Iet water flow into the mineral tank. When
water flow stops, open a cold water tap nearby and Iet run until air pressure is reIieved.
10.Electrical: AII electrical connections must be connected according to codes. Use electrical conduit if
applicable.
11. Plug into power supply.
Job Specification Sheet
* MODEL NO.
* WATER TEST
* CAPACITY PER UNIT MAX. PER REGENERATION
* MINERAL TANK SIZE DIA. HEIGHT
* BRINE TANK SIZE & SALT SETTING PER REGENERATION:
* F50 CONTROL VALVE SPECIFICATIONS
1 Type of Timer (see pages 18-21)
2 Timer Program Settings (see page 17)
A) Backwash min.
B) Brine & Slow Rinse min.
C) Rapid Rinse min.
D) Brine Tank Refill min.
3 Drain Line Flow Controller gpm
4 Brine Line Flow Controller gpm
5 lnjector Size #
6 A) Hard Water By-Pass
B) No Hard Water By-Pass
A) 7 day or 12 day
B) * 1,250 to 21,250 gallon meter or
* 6,250 to 106,250 gallon meter
* Other
C) Meter Wiring Package
1) System #4 - 1 tank; 1 meter; immediate or delayed regeneration
2) System #5 - 2 tanks; 2 meters; interlock
3) System #6 - 2 tanks; 1 meter; series regeneration
4) System #7 - 2 tanks; 1 meter; alternator
MODEL F50General Commercial Pre-Installation Check List
Installation Instructions
Page 3
MODEL F50Upper Control Drive Assembly (For 50 Mechanical)
Page 4
1 8
56
7
4-2
20
9
10
11
1213
1415
16171819
32
4-1
12
20
FOR SM
MODEL F50Lower Control Drive Assembly (For 50 Mechanical)
Page 6
12
3 45
6
78
9 10
11
12
13
14
15
1617
18
19
2021
2223
2425
MODEL F50Lower Control Drive Assembly (For 50 Mechanical)
Page 7
Item No. Quantity Part No. Description
1 1 051-00292-00 Conduit, Inter drive
2 2 051-00293-00 Conduit Connector
3 1 052-00117-00 Back Plate, Lower
4 1 052-00118-00 Bracket, Motor
5 4 066-00015-00 Screw
6 1 052-00124-00 Spacer, Indicator
7 1 099-01815-00 Drive Cam Assembly
8 1 052-00129-00 Pin, Spring
9 1 066-00015-00 Screw, Indicator
10 1 052-00120-00 Indicator, Off Line / Service / On Line
11 2 066-00047-00 Screw
12 1 043-00009-00 Micro Switch
13 1 052-00049-00 Insulator Switch
14 1 068-00018-00 Pin, Cam
15 2 066-00030-00 Screw, Motor Bracket
16 1 066-00015-00 Screw, Spacer
17 1 053-00025-00 Motor1 Assembly 220V
18 1 047-00016-00 Wire Assembly
19 2 066-00041-00 Screw, Window
20 1 051-00321-00 Window
21 1 060-00055-00 Seal, Window
22 1 060-00054-00 Seal, Cover
23 1 051-00321-00 Cover, Lower, Black
24 2 060-00037-00 O-Ring - Screw , Cover
25 2 052-00087-00 Screw, Cover
Bold faced items are recommended spare parts.
MODEL F50Assembly Drawings and Part NumbersMedium Brining System Assembly
Page 8
16
a.Brine Tube(NR WB)b.Brine Tube(R WB)
Fittings for medium (1" to 1/2")brining system
27
1
34
56
78 9
1314
1512
10 11
2
18
19
17
20
21
24
25
22
23
26
Fittings for 1/2" BV
BLOC K-C
BLOC K-A
BLOC K-B
MODEL F50Assembly Drawings and Part NumbersMedium Brining System Assembly Parts List
Page 9
Item No. Quantity Part No. Description
1 1 052-00000-00 End Plug-Brine System Assembly
2 1 060-00046-00 O-Ring- AS020
3 1 060-00050-00 RFC Washer-5.0 gpm
4 1 051-00121-01 Flow Control Retainer
5 1 052-00131-00 Piston- Brine System Assembly
6 1 052-00130-00 Piston Rod- Brine System Assembly
7 2 060-00069-00 O-Ring- AS210
8 1 051-00322-00 Spacer- Brine System Assembly
9 1 052-00054-00 Brine Valve Body
10 1 052-00045-00 Insert sleeve
11 1 051-00082-00 Retainer
12 1 052-00012-00 Nut
13 1 060-00013-00 Quad Ring- ASQ009
14 1 058-00008-00 Spring- Brine Valve
15 1 068-00019-00 Retaining Ring d3
16 1 052-00002-01 Stem Guide
17 1 066-00021-00 Screw,ch,M5x70mm,A2-70
18 1 052-00044-00 Injector Cover
19 1 060-00039-00 Injector Cover Gasket
201 051-00289-00 5# Injector Nozzle
1 051-00102-00 6# Injector Nozzle
21 1 075-00003-00 Injector Screen
22 1 051-00101-00 Injector Body
231 051-00290-00 5# Injector Throat
1 051-00107-00 6# Injector Throat
24 1 051-00093-00 Water Disperser
25 1 060-00040-00 Injector Body Gasket
26 1 052-00058-00 Elbow Fitting
27 1 051-00119-00 Air Check
Bold faced items are recommended spare parts.
MODEL F50Assembly Drawings and Part NumbersF50 Control Valve Assembly
Page 10
31
32
33
21
20
19
30
2
29
3
32
25
1012 10
11
171615
1314
2835
26
27
34
23
22
18
INLETOUTLET
2
3
1
24
11
FILTER PARTS
UPPER PI S TON ASS E MBLY
LOWER PI S TON ASS E MBLY
23
4 5 4 5 4 6
7 8 9
Block-A Block-B
MODEL F50Assembly Drawings and Part NumbersF50 Control Valve Assembly
Page 11
Item No. Quantity Part No. Description1 2 066-00054-00 Screw – Filter Valve2 1 052-00044-00 Injector Cover3 1 060-00040-00 Injector Body Gasket4 6 060-00065-00 Piston Seal5 5 051-00288-00 Spacer6 1 051-00285-00 End Spacer 7 1 051-00406-00 End Plug Assembly8 1 052-00112-00 Piston Rod9 1 052-00111-00 Upper Piston10 2 051-00165-00 Spacer11 4 060-00084-00 Piston Seal12 1 051-00320-00 Spacer13 1 051-00319-00 Black End Plug Assembly(NRWB)14 1 060-00021-00 O-Ring – End Plug15 1 052-00122-00 Lower Piston Rod16 1 051-00171-00 Snap Ring – Piston Rod17 1 052-00125-00 Lower Piston18 1 075-00003-00 Injector Screen19 1 051-00102-00 6# Injector Nozzle20 1 051-00101-00 Injector Body21 1 051-00107-00 6# Injector Throat22 1 052-00128-00 1” NPT Pipe Cap 23 2 066-00030-00 Screw – Valve Mounting24 1 060-00047-00 BWFC Washer, 25gpm
251 052-00001-00 1" Flow Control Housing (NPT)1 052-00151-00 1" Flow Control Housing (BSP)
26 1 060-00061-00 Inner O-Ring - Regeneration Port To Upper Valve27 1 060-00006-00 Outer O-Ring - Regeneration Port To Upper Valve28 1 060-00041-00 Riser O-Ring29 2 066-00021-00 Screw – Injector Body30 1 060-00039-00 Injector Cover Gasket
311 052-00108-00 Upper Valve Body (NPT)1 052-00274-00 Upper Valve Body (BSP)
32 2 060-00068-00 Coupling O-Ring33 2 052-00127-00 Upper To Lower Valve Coupling
341 052-00319-00 Lower 2” Lower Valve (NPT)1 052-00126-00 Lower 2” Lower Valve (BSP)
35 1 060-00033-00 Valve-Tank O-Ring
Bold faced items are recommended spare parts.
MODEL F50Assembly Drawings and Part Numbers 2" Flow Meter Assembly & Parts List
Page 12
1
2
3
4
5
6
78
910
11
14
13
12
ME C HANICAL ME TE R COVE R ASS 'Y E LE CTR ONIC ME TE R COVE R ASS 'Y
Item No. Quantity Part No. Description
1 1 052-00086-00 Impeller Shaft Retainer 2 1 051-00195-00 Impeller 3 1 052-00085-00 Impeller Shaft 4 1 060-00026-00 O-Ring 5 1 099-00734-00 Meter Cover Assembly (Mechanical) 6 4 066-00020-00 Screw-Hex Hd,M5*12
71 052-00320-00 2” Meter Body (NPT)1 052-00070-00 2” Meter Body (BSP)
8 1 060-00030-00 O-Ring-227
91 052-00321-00 Nipple Quick Connect (NPT)1 052-00071-00 Nipple Quick Connect (BSP)
10 1 051-00181-00 Flow Straightener 11 1 052-00072-00 Nut Quick Connect12 1 061-00003-00 Meter Cable Assembly (17.5”)
131 047-00013-00 Meter Cable Assembly (99.5”)1 047-00038-00 Meter Cable Assembly (300”)
14 1 099-01754-00 Meter Cover Assembly (Electronic)
Bold faced items are recommended spare parts.
Page 13
Commercial Demand Regeneration Control Timer Settings MODEL F50 ECONOMINDERTM
Typical Programming ProcedureCalculate the gallon capacity of the system, subtractthe necessary reserve requirement and set the gallonsrequired by Iifting the gallon dial and rotating it so thatthe number of gallons required is aligned with thewhite dot on program wheel gear. Release and checkfor firm engagement with gear.Note, drawing shows 8,750 gallon setting. The capac-ity (gallons) arrow denotes remaining gallons exclusiveof fixed reserve.
To set Meter capacity at initial start-up either 1. Rotate manual regeneration knob one full revolution. —or— 2. Rotate program wheel manually clockwise or counter clockwise and align white dot with capacity arrow. This procedure must be followed any time the program wheel setting is changed.
Note:
These timers do not have a 24 hour gear. Setting thegallons on the program wheel and manual regenera-tion procedure are the same as previous instructions.
lmmediate Regeneration Timers:
5. In any event, conditioned water may be drawn after rinse water stops flowing from the water conditioner drain Iine.
How To Set The Time Of Day: 1. Press and hold the red button in to is engage the 24 hour gear. 2. Turn the 24 hour gear until the actual time of day is at the time of day pointer 3. Release the red button to again engage the 24 hour gear.
How To Manually Regenerate Your Water Condi-tioner At Any Time: 1. Turn the manual regeneration knob cIockwise one “click.” 2. This slight movement of the manual regeneration knob engages the program wheel and starts the generation program. 3. The black center knob will make one revolution in the folIowing approximately three hours and stop in the position shown in the drawing. 4. Even though it takes three hours for this center knob to complete one revoIution, the regenera tion cycle of your unit might be set for only one half of this time.
TO MANUALLY
TO SET TIME OF DAY-PRESS RED BUTTON ANDTURN LARGE AIAL UNTILTIME IS AT ARROW.
START CYCLE-TURN KNOBCLOCKWISE.
CAPACITECAPACITYKAPAZITATCAPACITACAPACIDAD
M3
CAUTIONALWAYS REMOVE CABLE
FROM METER BEFORE
SWINGING TIMER OPEN.
Program Wheel
Manual Regeneration Knob
Red TimeSet Button
White Dot(M3 Capacity)
M3 Label
ServicePositionIndicator
Capacity(M3 Remaining)
24 HR. Gear
Page 14
Timer Setting ProcedureMODEL 3200 TIMER
How To Set Days On Which Water Conditioner Is ToRegenerate:
How To Set The Time Of Day:
How To Manually Regenerate Your WaterConditioner At Any Time:
How to Adjust Regeneration Time:1. Disconnect the power source.2. Locate the three screws behind the manual regeneration knob by pushing the red button in and rotating the 24 hour dial until each screw appears in the cut out portion of the manual regeneration knob.3. Loosen each screw slightly to release the pressure on the time plate from the 24 hour gear.4. Locate the regeneration time pointer on the inside of the 24 hour dial in the cut out.5. Turn the time plate so the desired regeneration time aligns next to the raised arrow.6. Push the red button in and rotate the 24 hour dial. Tighten each of the three screws.7. Push the red button and Iocate the pointer one more time to ensure the desired regeneration time is correct.8. Reset the time of day and restore power to the unit.
Rotate the skipper wheel until the number “1” is at the redpointer. Set the days that regeneration is to occur by slidingtabs on the skipper wheel outward to expose trip fingers.Each tab is one day. Finger at red pointer is tonight. Movingclockwise from the red pointer, extend or retract fingers toobtain the desired regeneration schedule.
Press and hold the red button in to disengage the drive gear.Turn the Iarge gear until the actual time of day is at the timeof day pointer.Release the red button to again engage the drive gear.
Turn the manual regeneration knob clockwise.This slight movement of the manual regeneration knobengages the program wheel and starts the regenerationprogram.The black center knob will make one revolutionin the following approximatelythree hours and stop in the position shown in the drawing.Even thought it takes three hours for this center knob tocomplete one revolution, the regeneration cycle of yourunit might be set only one half of this time.ln any event,conditioned water may be drawn after rinsewater stopsflowing from the water conditioner drain Iine.
TIME
OF DAY
ManualRegenerationKnob
24 HR. GearServicePositionIndicator
Red TimeSet Button
TO MANUALLY
TO SET TIME OF DAY-PRESS RED BUTTON AND
TURN LARGE DIAL UNTILTIME IS AT ARROW.
START CYCLETURN KNOBCLOCKWISE.
Skipper Wheel,12 Day(Shows Every OtherDay Regeneration)
Red Pointer
MODEL F50Timer Assembly (For Mechanical Clock)
Page 16
11
1615
13
12
1718
1920
21
6
22
23
2425
26
27
28
29
30
31
1
34
56
7
2
891032 6
14
24
27
27
MODEL F50Timer Assembly (For Mechanical Clock)
Page 17
Item No. Quantity Part No. Description
1 1 051-00078-00 Timer Housing
2 1 069-00180-00 Decal- Instructions
3 1 051-00074-00 Cycle Actuator Arm
4 1 099-00177-00 24 Hour Gear Assembly
5 1 051-00089-00 Knob
6 4 066-00002-00 Screw,tchw,NO.6-20x1/2,b,black,Zn,1022
7 1 069-00179-00 Button Decal
8 1 099-00176-00 Skipper Wheel Assembly
9 2 078-00008-00 Ball
10 2 058-00003-00 Spring –Detent- Skipper Wheel
11 1 069-00181-00 Decal- Time of Day
12 1 052-00013-00 Spring Clip
13 1 058-00002-00 Spring- Denent- Main Gear
14 1 051-00081-00 Plastic Ball-0.25inch Dia.
15 1 057-00023-00 Main Drive Gear
16 1 099-00178-00 Program Wheel(ST) Assembly
17 1 057-00016-00 Idler Pinion
18 1 058-00001-00 Spring- Idler
19 1 057-00014-00 Idler Gear
20 1 057-00013-00 Driver Gear
21 1 052-00046-00 Motor Mounting Plate
22 1 053-00022-00 Motor2 Assembly (220V/50HZ)
23 3 066-00010-00 Screw,ccch,NO.6-32x1/8,Zn,1022
24 2 066-00011-00 Screw,ccch,NO.6-32UNCx1/4,Zn,1022
25 1 052-00041-00 Hinge Bracket
26 2 066-00012-00 Screw,tchw,NO.8-18x3/8,Zn,1022
27 3 052-00048-00 Insulator- Drive Assembly
28 1 043-00003-00 Switch3
29 1 043-00002-00 Switch2
30 2 066-00055-00 Screw, tcp, NO. M3-24x1.125,b,Zn,1022
31 1 051-00070-00 Skipper Wheel Ring
32 1 051-00071-00 Regeneration Pointer
Bold faced items are recommended spare parts.
MODEL F50Timer Assembly (For Mechanical Meter)
Page 18
13
45
6
2
15
16
1718
1920
2122
23
5
24
25
26
27
28
29
3031
32
33
34
35
36
30
33
33
1314
6
9
7
810 11 12
MODEL F50Timer Assembly (For Mechanical Meter)
Page 19
Item No. Quantity Part No. Description
1 1 051-00078-00 Timer Housing
2 1 069-00188-00 Decal- Instructions2
3 1 057-00011-00 Cycle Actuator Gear- SM
4 1 051-00089-00 Knob
5 4 066-00002-00 Screw,tchw,NO.6-20x1/2,b,black,Zn,1022
6 2 069-00179-00 Button Decal
7 1 069-00186-00 Gallons Label
8 2 066-00008-00 Screw-PSWA
9 1 057-00012-00 Progran Skipper Wheel
10 1 051-00049-00 Dial
11
1 069-00043-00 Quantity Label-40ton
1 069-00184-00 Quantity Label-200ton
1 069-00185-00 Quantity Label-375ton
1 069-01125-00 Quantity Label-1200ton
12 1 051-00050-00 Retainer-PSWA
13 1 051-00068-00 Program Wheel Retainer
14 1 066-00026-00 Screw,tcc,NO.6-20x1/2,JIS SUS304
15 1 069-00181-00 Decal- Time of Day
16 1 052-00013-00 Spring Clip
17 1 057-00024-00 Main Drive Gear(SM)
18 1 099-00192-00 Program Wheel(SM) Assembly
19 1 057-00016-00 Idler Pinion
20 1 058-00007-00 Spring- Idler
21 1 057-00014-00 Idler Gear
22 1 057-00013-00 Driver Gear
23 1 052-00046-00 Motor Mounting Plate
24 1 053-00022-00 Motor2 Assembly(220V/50HZ(
25 3 066-00010-00 Screw,ccch,NO.6-32x1/8,Zn,1022
26 1 057-00021-00 Drive Pinion- Program Wheel
27 1 051-00085-00 Clutch Drive Pinion
28 1 058-00004-00 Spring
29 1 051-00069-00 Spring Retainer
30 2 066-00011-00 Screw,ccch,NO.6-32UNCx1/4,Zn,1022
31 1 052-00041-00 Hinge Bracket
32 2 066-00012-00 Screw,tchw,NO.8-18x3/8,Zn,1022
33 3 052-00048-00 Insulator- Drive Assembly
34 1 043-00004-00 Switch4
35 1 043-00002-00 Switch2
36 2 066-00055-00 Screw,tcp,NO.M3-24x1.125,b,Zn,1022
Bold faced items are recommended spare parts.
1. Softener fails to regenerate. A. Electrical service to unit has been interrupted.
B. Timer is defective.
C. Power failure.
A. By-pass valve is open.
B. No salt in brine tank.
C. Injector screen plugged.
D. Insufficient water flowing into brine tank.
E. Hot water tank hardness.
F. Leak at distributor tube.
G. Intemal valve Ieak.
H. Service adapter did not return to service.
A. Improper salt setting.
B. Excessive water in brine tank.
A. Iron buildup in Iine to water conditioner.
B. lron buildup in water conditioner.
C. Inlet of control plugged due to foreign material broken Ioose from pipes by recent work done on plumbing system.
A. Air in water system.
B. Improperly sized drain line flow control.
A. Fouled mineral bed.
A. Plugged drain Iine flow control.
B. Plugged injector system.
C. Timer not cycling.
D. Foreign material in brine valve.
E. Foreign material in brine iine flow control.
A. Assure permanent electrical service (check fuse, plug, pull chain or switch).
B. Replace timer.
B. Add salt to brine tank and maintain salt Ievel above water Ievel.
C. Reset time of day.
C. Clean injector screen.
D. Check brine tank fill time and clean brine line flow control if plugged.
E. Repeated flushings of the hot water tank is required.
F. Make sure distributor tube is not cracked. Check O-ring and tube pilot.
G. Replace seals and spacers and/or piston.
A. Check salt usage and salt setting.
B. See problem no. 7
A. Clean Iine to water conditioner.
A. Clean flow control.
B. Clean injector and screen.
C. Replace timer.
D. Replace brine vaIve seat and cIean valve.
E. Clean brine Iine flow control.
C. Remove piston and clean control.
B. Check for proper drain rate.
A. Check backwash, brine draw and brine tank fill. Increase frequency of regeneration. lncrease backwash time.
B. Clean control and add mineral cIeaner to mineral bed. lncrease frequency of regeneration.
A. Assure that well system has proper air eliminator control. Check for dry well condition.
H. Check drive motor and switch.
A. Close by-pass valve.2. Hard water.
3. Unit used too much salt.
4. Loss of water pressure.
5. Loss of mineral through drain Iine.
6. Iron in conditioned water.
7. Excessive water in brine tank.
Page 20
Service InstructionsMODEL F50
PROBLEM CAUSE CORRECTION
Problem: Softener Delivers Hard Water.
Cause couId be that . . . Reserve Capacity Has Been Exceeded.
Correction: Check salt dosage requirements and reset program wheel to provide additional reserve.
Cause could be that . . . Program Wheel Is Not Rotating With Meter Output.
Correction: Pull cable out of meter cover and rotate manually. Program wheel must move without binding and
clutch must give positive “clicks” when program wheel strikes regeneration stop. lf it does not, repIace timer.
Cause could be that . . . Meter Is Not Measuring Flow.
Correction: Check meter with meter checker.
General Service Hints For Meter Control
Page 21
Service Instructions (Cont’d.)MODEL F50
Clean drain Iine flow control.
Clean injector.
Clean screen.
lncrease Iine pressure to 20 P.S.I.
Change seals, spacers and piston assembly.
Check drive motor and switches.
Determine if switch or timer is faulty andreplace it, or replace complete power head.
Check timer program and positioning ofcontrol. Replace power head assembly if notpositioning properly.
Remove power head assembly and inspect bore.Remove foreign material and check control invarious regeneration positions.
Replace seals and piston assembly.
Drain Iine fIow controI is pIugged.
Injector is plugged.
Injector screen plugged.
Line pressure is too low.
InternaI control Ieak.
Service adapter did not cycle.
Missadjusted, broken or shorted switch.
Valve is not programing correctiy.
Foreign material in control.
InternaI control Ieak.
A.
B.
B.
C.
C.
D.
E.
F.
A.
A.
8. Softener fails to draw brine.
PROBL EM CAUSE CORRECTION
9. Control cycles continuously.
10. Drain flows continuously.
A.
B.
B.
C.
C.
D.
E.
F.
A.
A.
MODEL F50Dimensional Drawing
1) F50 Valve
Page 22
84.3mm
(3.32")
171.4mm
(6.75")
329.3mm
(12.96")
52.9mm
(2.08")
TAN
K
100mm
(3.94")
316.1mm (12.45")
173.5mm (6.83")
55.8mm (2.20")
222.4mm
(8.76")
75.5mm
(2.97")
91.3mm
(3.60")
31.9mm
(1.26")
25.4mm (1" )
12.7mm (1/2")101.6m
m (4"-8 U
N)
172mm (6.78")
MODEL F50Timer Assembly (For Mechanical Meter)
Page 23
Piston Kits100-00015-00 Piston Kits-NRWB
Adapters100-00003-00 Fittings for medium (1” to 1/2”)
brining system
100-00027-00 Fittings for 1/2” BV
Seals & Spacers100-00045-00 F50 Spacers & Seals
Injector100-00021-00 #5 Injector Assembly
100-00026-00 #6 Injector Assembly
Meter (2" Electronic Flow Meter)
100-00038-00 99.5" Cable
100-00069-00 300" Cable
Meter(2" Extended Mechanical Flow Meter)
100-00042-00
Medium ½” Brine Valve
100-00031-00 Brine Valve Assembly RFC060-00100-00 5.0G
BWFC060-00072-00 0G
060-00047-00 25G
BWFC Housing Assembly100-00013-00 1” NPT 25G
100-00142-00 1” BSP 25G
AAHK076-00017-00V1.0
top related