leica distotm d1 - leica geosystems...technicaldata techncaldaa leicadisto™d1 3 general...
Post on 15-Aug-2020
5 Views
Preview:
TRANSCRIPT
Leica DISTOTM D1The original laser distance meter
Overview 2
Technical data 3
Instrument Set-up 5
Operations 11
Message Codes 14
Care 15
Warranty 16
Safety instructions 17
Leica DISTO™D1 1
OverviewOv e rv ie w
The Leica DISTO™ is a laser distancemeter oper-ating with a class2 laser. See chapter Technicaldata for scope of use.
1 Display
2 ON/Measure
3 Clear/ OFF
Leica DISTO™D1 2
Technical dataTe c h n ic a ld a ta
Leica DISTO™D1 3
General
Accuracywith favourable conditions * 2mm / 0.08 in ***
Accuracywith unfavourable conditions ** 3mm / 1/8" ***
Range with favourable conditions * 0.2 - 40m / 0.6 - 120 ft ***
Range with unfavourable conditions ** 0.2 - 30m / 0.6 - 100 ft ***
Smallest unit displayed 0.1mm / 1/32 in
Laser class 2
Laser type 635 nm, <1mW
ø laser point | at distances 6 /30 /60mm | 10/ 50/ 100m
Protection class IP54 (dust- and splash water protected)
Auto. laser switch off after 90 s
Auto. power switch off after 180 s
Bluetooth® Smart Bluetooth® v4.0
Range of Bluetooth® Smart <10m
Battery durability (2 xAAA) up to 10000measurements
Dimension (H xD xW) 115 x43.5 x23.5mm | 4.53 x1.71 x0.93 in
Weight (with batteries) 87 g/ 3.07 oz
Temperature range Storage | Operation -25 to 70°C/ -13 to 158°F | -0 to 40°C/ 32 to 104°F
* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination andmoderate temperatures.** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range.*** Tolerances apply from 0.05m to 5m with a confidence level of 95%.With favourable conditions the tolerancemay deteriorate by 0.10mm/m for distances above 5m.With unfavourable conditions the tolerancemay deteriorate by 0.15mm/m for distances above 5m.
Technical data
Functions
Distancemeasuring yes
Permanent measuring yes
Beep yes
Illuminated display yes
Bluetooth® Smart yes
Leica DISTO™D1 4
Instrument Set-upIn s tru me n tSe t-u p
Introduction
The safety instructions (see SafetyInstructions) and the user manualshould be read through carefullybefore the product is used for the firsttime.
The person responsible for theproduct must ensure that all usersunderstand these directionsandadhere to them.
The symbols used have the followingmeanings:
WARNING
Indicatesa potentially hazardous situ-ation or an unintended use which, ifnot avoided, will result in death or ser-ious injury.
CAUTION
Indicatesa potentially hazardous situ-ation or an unintended use which, ifnot avoided, may result in minor injuryand/or appreciablematerial, financialand environmental damage.
Important paragraphswhichmust be adhered to in practiceas theyenable the product to beused in a technically correct andefficient manner.
5Leica DISTO™D1
Instrument Set-up
Insert batteries
To ensure a reliable use, we recom-mend using high qualityAlkaline bat-teries. Change batterieswhenbattery symbol is flashing.
Leica DISTO™D1 6
Instrument Set-up
Switching ON/OFF
Device is turnedOFF.
Leica DISTO™D1 7
Instrument Set-up
Clear
Undo last action. Leave actual function, go to defaultoperationmode.
Leica DISTO™D1 8
Instrument Set-up
Message Codes
If themessage "i" appearswitha number, observe the instruc-tions inMessage Codes section.Example:
Leica DISTO™D1 9
Instrument Set-up
Settings
Pressboth keys simultaneousley. Switch between the following units:
0.000m0'00" 1/160.0000m0.000 in0.00 ft0 in 1/16
Leica DISTO™D1 10
OperationsOp e ra tio n s
Measuring single distance
Aim active laser at target.Target surfaces: Measuringerrors can occur whenmeas-uring to colourless liquids, glass,styrofoam or permeable sur-facesor when aiming at highgloss surfaces. Against dark
surfaces themeasuring timeincreases.
11Leica DISTO™D1
Operations
Permanent measuring
The last valuemeasured is displayedin themain line.
Stopspermanent measuring.
Leica DISTO™D1 12
Operations
Bluetooth® Smart
DISTO™sketch. Use App forBluetooth® data transfer.
Bluetooth® Smart is alwaysact-ive when the device is switchedon. Connect the device withyour smart-phone, tablet,laptop.. Measurement valueswill be transferred automaticallyright after ameasurement. Theefficient and innovativeBluetooth® Smart module (withthe new Bluetooth® standardV4.0) works together with allBluetooth® Smart Ready
devices. All other Bluetooth®devicesdo not support theenergy saving Bluetooth®Smart Module, which is integ-rated in the device.
We provide no warranty for freeDISTO™software and offer nosupport for it. We accept no liab-ilitywhatsoever arising from theuse of the free software and weare not obliged to provide cor-rectionsnor to develop
upgrades. Awide range of com-mercial software can be foundon our homepage. Apps forAndroid® or iOS can be found inspecial internet shops. For moredetails, see our homepage.
Leica DISTO™D1 13
Message CodesMe s s a g e Co d e s
Leica DISTO™D1 14
No. Cause Correction
204 Calculation error Performmeasurement again.
220 Hardware error Contact your dealer
240 Data transfer error Connect device and repeat procedure
252 Temperature too high Let device cool down.
253 Temperature too low Warm device up.
255 Received signal too weak, measuring time too long Change target surface (e.g. white paper).
256 Received signal too high Change target surface (e.g. white paper) .
257 Toomuch background light Shadow target area.
* If other message codes are displayed frequently even the instrument has been switched off and on, please contact your dealer.
CareCa re
l Clean the device with a damp, soft cloth.
l Never immerse the device in water.
l Never use aggressive cleaning agents orsolvents.
Leica DISTO™D1 15
WarrantyWa rra n ty
Warranty under PROTECT by LeicaGeosystems
Lifetime Manufacturer´s Warranty
Warranty coverage for the entire usage time ofthe product under PROTECT according to LeicaGeosystems International LimitedWarranty andPROTECT GeneralTerms&Conditions set outunder www.leica-geosystems.com. Free ofcharge repair or replacement of all products oranyparts under PROTECT that suffer defects asa result of faults in materials or workmanship.
3 Years No Cost
Additional services should the product underPROTECT become defective and require ser-vicing under normal conditionsof use, asdescribed in the user manual, at no additionalcharge.
To receive the "3 YearsNoCost" period, theproduct under PROTECT must be registered atmyworld.leica-geosystems.comwithin 8 weeksofthe purchase date. If the product underPROTECT is not registered, a "2 yearsNoCost"period applies.
Leica DISTO™D1 16
Safety instructionsSa fe ty in s tru c tio n s
The person responsible for the instrumentmust ensure that all users understand thesedirectionsand adhere to them.
Leica DISTO™D1 17
Safety instructions
Symbols used
The symbols used have the followingmeanings:
WARNING
Indicatesa potentially hazardous situation or anunintended use which, if not avoided, will result indeath or serious injury.
CAUTION
Indicatesa potentially hazardous situation or anunintended use which, if not avoided, may result inminor injury and/or appreciablematerial, financialand environmental damage.
Important paragraphswhichmust beadhered to in practice as theyenable theproduct to be used in a technically correctand efficient manner.
Leica DISTO™D1 18
Safety instructions
Permitted use
l Measuring distances
l Data transfer with Bluetooth®
Leica DISTO™D1 19
Safety instructions
Prohibited use
l Using the product without instruction
l Using outside the stated limits
l Deactivation of safety systemsandremoval of explanatory and hazard labels
l Opening of the equipment byusing tools(screwdrivers, etc.)
l Use of accessories from other man-ufacturerswithout expressapproval
l Carrying out modification or conversionof the product
l Deliberate dazzling of third parties; also inthe dark
l Inadequate safeguardsat the surveyingsite (e.g. whenmeasuring on roads, con-struction sites, etc.)
l Deliberate or irresponsible behaviour onscaffolding, when using ladders, whenmeasuring near machineswhich are run-ning or near parts of machinesor install-ationswhich are unprotected
l Aiming directly in the sun
Leica DISTO™D1 20
Safety instructions
Hazards in use
WARNING
Watch out for erroneousmeasurements if theinstrument is defective or if it hasbeen dropped orhasbeenmisused or modified. Carry out periodictest measurements. Particularly after the instru-ment hasbeen subject to abnormal use, andbefore, during and after important meas-urements.
CAUTION
Never attempt to repair the product yourself. Incase of damage, contact a local dealer.
WARNING
Changesor modificationsnot expressly approvedcould void the user´s authority to operate theequipment.
Leica DISTO™D1 21
Safety instructions
Limits of use
Refer to section Technical data. The deviceis designed for use in areaspermanently hab-itable byhumans. Do not use the product inexplosion hazardousareasor in aggressiveenvironments.
Leica DISTO™D1 22
Safety instructions
Areas of responsibility
Responsibilities of the manufacturer of the ori-ginal equipment:
Leica GeosystemsAGHeinrich-Wild-StrasseCH-9435 HeerbruggInternet: www.leica-geosystems.com
The companyabove is responsible for supplyingthe product, including the User Manual in a com-pletely safe condition.
The companyabove is not responsible for thirdparty accessories.
Responsibilities of the person in charge of theinstrument:
l To understand the safety instructionsonthe product and the instructions in theUser Manual.
l To be familiar with local safety regulationsrelating to accident prevention.
l Alwaysprevent access to the product byunauthorised personnel.
Leica DISTO™D1 23
Safety instructions
Disposal
CAUTION
Flat batteriesmust not be disposed of with house-hold waste. Care for the environment and takethem to the collection points provided in accord-ance with national or local regulations.
The product must not be disposed with householdwaste. Dispose of the product appropriately inaccordance with the national regulations in forcein your country. Adhere to the national and coun-try specific regulations.
Product specific treatment and wasteman-agement can be downloaded from ourhomepage.
Leica DISTO™D1 24
Safety instructions
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to themost stringent require-ments of the relevant standardsand regulations.However, the possibility of causing interference inother devices cannot be totally excluded.
Japanese Radio Law Compliance
This device is granted pursuant to the JapaneseRadio Law電波法 . This device should not bemodified otherwise the granted designation num-ber will become invalid.
Leica DISTO™D1 25
Safety instructions
FCC statement (applicable in U.S.)
This equipment hasbeen tested and found to com-plywith the limits for a ClassB digital instrument,pursuant to part 15 of the FCC rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residential install-ation. This equipment generates, usesand canradiate radio frequencyenergyand, if not installedand used in accordance with the instructions, maycause harmful interference to radio com-munications.
However, there is no guarantee that interferencewill not occur in a particular installation. If this equip-ment does cause harmful interference to radio ortelevision reception, which can be determined byturning the equipment off and on, the user isencouraged to try to correct the interference byone or more of the followingmeasures:
l Reorient or relocate the receivingantenna
l Increase the separation between theequipment and the receiver
l Connect the equipment into an outlet ona circuit different from that to which thereceiver is connected
l Consult the dealer or an experienced radi-o/TV technician for help
This device complieswith part 15 of the FCCrules. Operation is subjected to the following twoconditions:
l This devicemaynot cause harmful inter-ference, and
l this devicemust accept any interferencereceived, including interference that maycause undesired operation.
FCC Radiation Exposure Statement
The radiated rf output power of the instrument isbelow the FCC radio frequencyexposure limits forportable devicesaccording to KDB447498.
Leica DISTO™D1 26
Safety instructions
ISED Statement (applicable in
Canada)
This device complieswith IndustryCanada'slicense-exempt RSSs. Operation is subject to thefollowing two conditions:
l This devicemaynot cause harmful inter-ference, and
l this devicemust accept any interference,including interference that maycauseundesired operation of the device.
Radio Frequency (RF) Exposure ComplianceStatement
The radiated rf output power of the instrument isbelow the Health Canada'sSafetyCode 6 exclu-sion limit for portable devices (radiated elementseparation distance between the radiating ele-ment and user and/or bystander is below 20 cm).
Leica DISTO™D1 27
Safety instructions
Use of the product with Bluetooth®
WARNING
Electromagnetic radiation can cause disturbancesin other equipment, in installations (e.g. medicalones such aspacemakers or hearing aids) and inaircraft. It can also affect humansand animals.
Precautions:
Although this product conforms to themost strin-gent standardsand regulations, the possibility ofharm to people and animals cannot be totallyexcluded.
l Do not use the product near petrol sta-tions, chemical plants, in areaswith apotentially explosive atmosphere andwhere blasting takesplace.
l Do not use the product near medicalequipment.
l Do not use the product in airplanes.
l Do not use the product near your bodyfor extended periods.
Leica DISTO™D1 28
Safety instructions
Laser classification
The device produces visible laser beams, whichare emitted from the instrument: It is a Class2laser product in accordance with:
l IEC60825-1 : 2014 „Radiation safety oflaser products“
Laser Class 2 products:
Do not stare into the laser beam or direct ittowardsother people unnecessarily. Eye pro-tection is normally afforded byaversion responsesincluding the blink reflex.
WARNING
Looking directly into the beamwith optical aids(e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beammaybe hazardous tothe eyes.
Wavelength620 - 690 nmMaximum radiant output power for classification< 1mW
Pulse duration> 400 psPulse repetition frequency320MHzBeam divergence0.16 x0.6mrad
Leica DISTO™D1 29
Safety instructions
Labelling
Subject to change (drawings, descriptionsandtechnical data) without prior notice.
Leica DISTO™D1 30
top related