its italia · autolubrificanti, boccole rilubrificabili, boccole in bronzo o ferro sinterizzate,...
Post on 23-Aug-2020
8 Views
Preview:
TRANSCRIPT
b y I T S I t a l i a
ITS ITALIA
Cuscinetti a strisciamento Sliding bearings
Catalogo teCniCo
teCHniCal Catalog
Indice | Index
Guida al calcolo dimensionale | Dimensional calculation guide ............................................2-3
Caratteristiche e applicazioni Djamond | Djamond features and applications .........................4-5
Boccole autolubrificanti PT..SL | Self lubricating bushings PT..SL ..........................................6-7
Tabelle dimensionali PT..SL | Table of dimensions PT..SL ....................................................8-11
Boccole rilubrificabili PT..RK | Relubricating bushings PT..RK ............................................12-13
Tabelle dimensionali PT..RK | Table of dimensions PT..RK .................................................14-15
Boccole in bronzo/ferro sinterizzato BZ../FE.. | Bronze/Iron sintered bushings BZ../FE.. ......16-17
Tabelle dimensionali BZ../FE.. | Table of dimensions BZ../FE.. ..........................................18-19
Elementi autolub. a secco BG../AG../CG.. | Self lubr. dry elements BG../AG../CG.. . ............20-21
Tabelle dimensionali BG../AG../CG.. | Table of dimensions BG../AG../CG.. .........................22-24
Boccole rullate in bronzo PB..AR/AC | Rulled bronze bushings PB..AR/AC ..........................26-27
Tabelle dimensionali BG../AG../CG.. | Table of dimensions BG../AG../CG.. .........................28-29
Boccole bimetalliche BJ.. | Bimetallic bushings BJ.. . .......................................................30-32
Guida al calcolo dimensionale
Lo scopo di questo manuale è di fornire informazioni tecniche dettagliate sulle caratteristiche delle boccole Djamond.Le informazioni fornite consentono al progettista di definire la dimensione corretta della boccola richiesta e di stimarne la durata e le prestazioni.I servizi ricerca e sviluppo di I.T.S. ITALIA sono disponibili per fornire ulteriore assistenza su problemi e progetti particolari.
Forme disponibiliParticolari standard normalmente disponibili a stock
Questi prodotti sono costruiti secondo normative nazionali e internazionali.Dimensioni metriche e in pollici• Boccole cilindriche• Boccole flangiate• Rondelle di spinta• Nastri
Prestazioni
Parametri di Progetto
I principali parametri quando si determina la dimensione o quando si calcola la durata di una boccola sono:• Limite di carico specifico• Fattore PV• Rugosità della superficie del contropezzo Ra• Materiale del contropezzo• Temperatura• Altri fattori ambientali, ad esempio tipo di alloggiamento, presenza di sporco, lubrificazione
CalcoloDue metodi di progetto sono previsti come segue:• Calcolo della durata basato sulle dimensioni della boccola consentite• Calcolo delle dimensioni della boccola necessarie basato su una durata richiesta
Carico specificoAllo scopo di valutare le prestazioni della boccola il carico specifico P è definito come il carico di lavoro diviso per l’ area proiettata del boccola ed è espresso in N/mm2.
Limite di carico specificoIl carico massimo che puó essere applicato ad una boccola a strisciamento può essere espresso in termini di limite di carico specifico, il quale dipende dal tipo di carico. Esso ha un valore massimo di carico statico.Condizioni di carico dinamico o di movimento oscillante provocano sollecitazioni a fatica nella boccola e quindi una riduzione del limite di carico specifico. Il carico specifico su una boccola non dovrebbe superare i limiti di carico specifico forniti nelle relative tabelle.I valori di limite di carico specifico indicati nelle tabelle presuppongono un buon allineamento tra la boccola e il contropezzo.
Fattore PVLa durata operativa utile di una boccola a strisciamento è regolata dal fattore PV, il prodotto del carico specifico P[N/mm2] e della velocità di strisciamento V [m/s].Per le rondelle di spinta e le superfici di spinta delle boccole flangiate viene utilizzata la velocità di strisciamento sul diametro medio.
Fattori di applicazione
I seguenti fattori influenzano le prestazioni della boccola e devono essere considerati calcolando le dimensioni o stimando la durata operativa della boccola per una applicazione particolare.
TemperaturaLa durata operativa di una boccola a strisciamento dipende dalla temperatura di funzionamento.Sotto condizioni di funzionamento a secco il calore generato dall’ attrito sulla superficie di scorrimento della boccola dipende dal fattore PV.Per un dato Fattore PV la temperatura di funzionamento della boccola dipende dalla temperatura dell’ambiente circostante e dalle proprietà di dissipazione del calore della sede. Il funzionamento intermittente favorisce la dissipazione del calore dall’insieme boccola - sede e riduce la temperatura media di funzionamento della boccola.
Modifiche sulle boccole a strisciamento
Taglio e lavorazioneLa modifica dei componenti Djamond non richiede procedimenti particolari. In generale è meglio eseguire le operazioni di lavorazione e foratura dal lato interno al fine di evitare bave. Quando il taglio è eseguito dal lato esterno, deve essere usata la pressione di taglio minima e fare attenzione di assicurare che tutte le particelle di acciaio o di bronzo e tutte le bave siano eliminate.
Esecuzione dei fori olioLe boccole devono essere supportate adeguatamente durante l’ operazione di foratura per assicurare che non ci sia deformazione causata dalla pressione di foratura.
Taglio dei nastriIl nastro può essere tagliato a misura con uno qualsiasi dei seguenti metodi.Si deve fare attenzione nel proteggere la superficie della boccola ed assicurare che non si verifichi una deformazione del nastro:• Utilizzando una fresa a spianare a tre tagli, o una sega circolare, con il nastro in piano e assicurato ad una fresatrice orizzontale.• Spuntatura• Ghigliottina (solo per larghezze inferiori a 90 mm)• Taglio a getto d’ acqua• Taglio laser (vedere avvertimenti sanitari)
2
Dimensional calculation guide
The purpose of this handbook is to provide comprehensive technical information regarding characteristics of Djamond bearings.The information given may assist designers to establish the correct size of required bearing as well as the expected life and performance.I.T.S. ITALIA Research and Development services are available to assist with any unusual design problems.
Basic Forms AvailableStandard Components available from stock.
These products are manufactured according to International and National standards.Metric and Imperial sizes• Cylindrical Bushes• Flanged Bushes• Thrust Washers• Flanged Washers• Strip Material
Performance
Design FactorsThe main parameters to determine the size or calculate the service life for a bearing are:• Specific Load Limit• PV Factor• Mating surface roughness Ra• Mating surface material• Temperature T• Other environmental factors e.g. Housing design, dirt, lubrication
CalculationTwo design procedures are provided as follows:• A bushing service life calculation based on the permitted bearing dimensions• A calculation of the bushing dimensions based on the required bushing service life
Specific LoadTo evaluate the bearing performance the specific load P is defined as the working load divided by the projected area of the bearing and is expressed in N/mm2.
Specific Load Limit
The maximum load which can be applied to a bearing can be expressed in terms of the Specific Load Limit, which depends on the type of the loading. It is highest under steady loads. Conditions of dynamic load or oscillating movement which produce fatigue stress in the bearing result in a reduction in the permissible Specific Load Limit.In general the specific load on a bearing should not exceed the Specific Load Limits given in the related tables.The values of Specific Load Limit specified in the tables assume good alignment between the bearing and mating surface.
PV FactorThe useful operating life of a bearing is regulated by the PV factor, which is the product of the specific load P[N/mm2] and the sliding speed V [m/s].For the thrust washers and the surface of flanged bushing is used the sliding speed on the mean diameter.
Application FactorsThe following factors influence the bushing’s performance and must be considered to calculate the required dimension or to estimate the bearing life for a particular application.
TemperatureThe lifetime of a bearing depends on the operating temperature.Under dry conditions the frictional heat generated on the sliding surface of the bearing depend on the PV factor.For a given PV factor the operating temperature of the bushing depends on the temperature of the surrounding environment and the heat dissipation properties of the housing. Intermittent operation helps the heat dissipation from the couple housing - bushing and reduce the operating temperature of the bushing.
Modification
Cutting and MachiningThe modification of Djamond bearing components requires no special procedures. In general it is more satisfactory to perform machining or drilling operations from the inside of the bushing to avoid burrs. When the cutting is made from outside, a minimum cutting pressure should be used to ensure that any steel or bronze particles projecting on the remaining bearing surface, and all burrs, are removed.
Drilling Oil HolesBushes should be adequately supported during the drilling operation to ensure that no distortion is caused by the drilling pressure.
Cutting Strip MaterialThe strip material may be cut to desired size by any of the following methods.Take care to protect the bearing surface from any damage and to avoid any deformation of the strip:• Using side and face cutter, or slitting saw, with the strip held flat and securely on a horizontal milling machine.• Cropping• Guillotine (For widths less than 90 mm only)• Water-jet cutting• Laser cutting (see Health Warning)
3
4
Djamond è il marchio di qualità che certifica i cuscinetti a strisciamento di produzione ITS Italia. La gamma di prodotti è composta da boccole autolubrificanti, boccole rilubrificabili, boccole in bronzo o ferro sinterizzate, elementi autolubrificanti a secco, boccole rullate in bronzo e boccole bimetalliche. Gli alti standard qualitativi garantiti dai prodotti Djamond sono sinonimo di prestazioni di prim’ordine e lunga durata nel tempo.
BJ
PB
BG
BZ
PT..SL/RK
Djamond is the quality brand for sliding bushings produced by ITS Italia. The range of producs is composed by self lubricating bushings, relubricating bushings, sintered bronze or iron bushings, dry lubricating elements, rolled bronze bushings and bimetallic bushings. The high quality standards of Djamonds products are synonymous of top class performance and long lasting in time.
ESEM
PI D
I APP
LIC
AZI
ON
I | A
PPLI
CAT
ION
EXA
MPL
ESDjamond
Caratteristiche e applicazioni
5
BRONZO SINTERIZZATO
SINTERED BRONZE
AUTOLUBRIFICANTI IN PTFE
SELF LUBRICATING PTFE
RILUBRIFICABILI IN POM/PEEK
RELUBRICATING POM/PEEK
BRONZO ALVEOLARIRULLED BRONZE
BRONZO GRAFITECAST BRONZE/
GRAPHITE
BIMETALLICHEBIMETAL
BZ.. PT..SL PT .. RK PB .. AR/AC BG .. A /B /C BJ..
AUTOLUBRIFICANTESELF-LUBRICATING
● ● ● ● ● ● ● - ● ● ● -
ESENTE DA MANUTENZIONEMAINTENANCE-FREE
● ● ● ● ● ● ● ● ● ● ● ●
CARICO ELEVATOHIGH LOAD
- ● ● ● ● ● ● ● ● ● ●
ALTA VELOCITA’HIGH SPEED
● ● ● ● ● ● ● ● ● ●
BASSO ATTRITO LOW FRICTION
● ● ● ● ● ● ● ● - ● ● -
ALTE TEMPERATUREHIGH TEMPERATURE
- ● ● ● ● ● ● ● ● ● ●
ADATTABILITA’ IN AMBIENTE SPORCODIRTY ENVIRONMENT
● - ● ● ● ● ● ● ● ● ●
RESISTENZA ALLA CORROSIONECORROSION RESISTANCE
● ● ● ● ● ● ● ●
TOLLERABILITA’ AL DISALLINEAMENTOMISALIGNMENT
● - ● ● ● ● ●
FUNZIONAMENTO A GIOCO RIDOTTOREDUCED CLEARANCE
● ● ● ● ● ● ● ● ● ● ●
SCARSA FINITURA DEL CONTROPEZZO LOW FINISHING OF MATING SURFACE
- - ● ● - ●
RISPOSTA A VIBRAZIONI E URTIVIBRATION AND SHOCK
● ● ● ● ● ● ● ● ● ●
LEGENDA ● ● ● OTTIMO ● ● BUONO ● ADATTO - NON IDONEOLEGEND ● ● ● VERY WELL ● ● GOOD ● SUITABLE - UNSUITABLE
RASSEGNA DELLE CARATTERISTICHECHARACTERISTICS
DjamondFeatures and applications
6
CARATTERISTICHE
Definite anche col termine di CUSCINETTI A SECCO grazie al loro strato di Ptfe, raggruppano in se vari vantaggi:
• Sono esenti da manutenzione• Hanno buone proprietà di attrito con bassa
usura ed elevata capacità di carico• Velocità di strisciamento elevata• Range di temperature di lavoro molto elevate• Effetto stick-slip trascurabile• Gioco di funzionamento contenuto• Buona resistenza chimica• Basso assorbimento d’acqua e rigonfiamento
MATERIALE
Sono costituite da un’armatura in acciaio a basso tenore di carbonio che conferisce resistenza meccanica e rivestite esternamente con 2µm di rame o altro trattamento di protezione. Internamente uno strato di bronzo poroso sinterizzato sulla parete garantisce una buona adesione dello strato di PTFE all’acciaio. Possono essere sottoposte a lavorazione meccanica, tranne che nella superficie di strisciamento se non per eventuali canaline per far scorrere l’olio lubrificante. E’ inoltre possibile avere pareti in bronzo (amagnetico) o acciaio inossidabile. Per maggiori dettagli fare riferimento a pag. 4.
LUBRIFICAZIONE
Nella fase iniziale di rodaggio una parte del Ptfe viene trasferito nella superficie di contatto creando un film lubrificante che consente un basso attrito senza lubrificazione. Discreta incorporabilità delle sostanze abrasive, ottimo il funzionamento con olio che oltre a lubrificare sottrae calore alla superficie di scorrimento allungando la vita della boccola. Sconsigliato invece l’uso di grasso che tende a far staccare il Ptfe se non manutenzionato con regolarità. Non usare additivi a base MoS2.
APPLICAZIONI
I Settori sono i più vari dagli elettrodomestici all’industria automobilistica al settore farmaceutico, alimentare. Indicate soprattutto dove ci sono alti carichi e velocità medio basse anche oscillanti.
MONTAGGIO
La boccola va montata per interferenza con la zona di giunzione opposta alla direzione del carico, utilizzando un mandrino scalinato e prevedendo degli smussi d’invito di 15°/20° sulla sede in tolleranza H7, mentre l’albero in tolleranza f7 (oltre d.75 = h7) è consigliato di durezza HB 300 ÷ 600 con una rugosità inferiore 0,4 µm (nel caso della ghisa 0,3 µm). Se necessario per il fissaggio è possibile l’utilizzo di collanti sintetici.
Serie PT..SL BOCCOLE AUTOLUBRIFICANTImultistrato con PTFE composito
Caratteristiche U.M. PT..SL PT..SLBCarico ammissibile (din./stat.) N/mm2 80/250 80/140
Resistenza a compressione N/mm2 350 300
Velocità di strisc. ammissibile m/s 2 2
Coeff. di attrito µ - 0,03 ÷ 0,08 0,03 ÷ 0,08
Campo di temperature °C -200 ÷ +250 -200 ÷ +250
PVmax N/mm2 x m/s 3,6 3,6
7
PT..SL seriesSELF LUBRICATING BUSHINGS multilayer with composite PTFE
FEATURES
Suitable for dry running with a low coefficient of friction, low wear rate, good sliding characteristics, the transfer film created will protect the mating metal surface.Suitable for turning and oscillating movement, high chemical resistance, lower absorption of water and reduce swelling. Also performs well with lubrication.
STRUCTURE
PTFE/Fiber mixture thickness 0.01~0.03mm, provides an excellent initial transfer film, which effectively coats the mating surfaces of the bushing assembly, forming an oxide type solid lubricant film. Sintered bronze powder thickness 0.20-0.35mm,provides Max. thermal conductivity away from the bushing surface,also serves as a reservoir for the PTFE-Fiber mixture. SL: Low-carbon steel,gives exceptionally high load carrying capacity, excellent heat dissipation.Copper/Tin plating thickness 0.002mm, provides good corrosion resistance. SLB: Bronze backing, provides exceptionally high load carrying capacity, excellent heat dissipation and very good corrosion resistance. SLSS (STANDARD AISI316): Stainless steel backing, provides very good corrosion resistance.
TYPICAL APPLICATIONS
SL: This material meets the demanding criteria for long life and trouble-free performance with or without lubrication.Automotive,business machines,hydraulics and valves, home appliances, materials handling, marine engine, packaging, textile equipment, tools...etc. SLB: This material meets the demanding criteria for long life and trouble-free performance with or without lubricant, of high safety factor even. The typical applications covered Steel metallurgy industry such as bushes for roller grooves of successive casting machines, cement grouting pumps and screw conveyors for cement and so on.
STRUTTURA La struttura dei cuscinetti radenti esenti da manutenzione “SL”, è in tre varianti che differiscono per il tipo di armatura:• SL con armatura in acciaio• SLB con armatura in bronzo• SLSS con armatura in acciaio inox
Versione “SL”
La versione “SL” è composta da tre strati:• armatura in acciaio• strato di bronzo poroso• strato di strisciamento
Sull’armatura in acciaio viene sinterizzato uno strato di bronzo poroso (bronzo allo stagno) con spessore da 0,2 mm a 0,35 mm. Durante la fase di laminazione viene inserito, nei pori dello strato di bronzo poroso, uno strato di strisciamento costituito da una miscela di politetrafluoroetilene (PTFE) spesso da 0,01 a 0,03 mm.
Versione “SLB”
Anche la versione “SLB” è costituita da tre strati. Al posto dell’armatura in acciaio, questa versione ha un’armatura in bronzo. Lo strato di bronzo poroso e lo strato di strisciamento sono uguali a quella della versione “SL”. L’armatura in bronzo conferisce al cuscinetto radente alta resistenza alla corrosione ed ottima conducibilità termica.
Versione “SLSS” (STANDARD AISI316)
Come le precedenti versioni anche questa consta di tre strati. L’armatura di questa versione è però in acciaio inox la quale conferisce al cuscinetto radente un ottima resistenza alla corrosione.
PTFE caricato
Bronzo poroso allo stagno
Armatura in acciaio
Protezione superficiale
8
d D
AlberoShaft
f7
SedeHousing
H7
PareteWall
min/max
f1 f2
SIGLADesignation
L 0 / -0.4
4 5 6 8 10 12 15 20 25 30 40 50
3 4,5 3 -0,006-0,016 4,5 +0,012
+0 0,730 0,750
0,5 0,3
PTC..SL0304
PTC..SL0305
PTC..SL0306
4 5,5 4 -0,010-0,022 5,5 +0,012
+0PTC..SL
0404PTC..SL
0406PTC..SL
0408
5 7 5 -0,010-0,022 7 +0,015
+0
0,980 1,005
PTC..SL0505
PTC..SL0508
6 8 6 -0,010-0,022 8 +0,015
+0PTC..SL
0606PTC..SL
0608PTC..SL
0610
8 10 8 -0,013-0,028 10 +0,015
+0PTC..SL
0806PTC..SL
0808PTC..SL
0810PTC..SL
0812PTC..SL
0815
10 12 10 -0,013-0,028 12 +0,018
+0PTC..SL
1006PTC..SL
1008PTC..SL
1010PTC..SL
1012PTC..SL
1015PTC..SL
1020
12 14 12 -0,016-0,034 14 +0,018
+0PTC..SL
1206PTC..SL
1208PTC..SL
1210PTC..SL
1212PTC..SL
1215PTC..SL
1220PTC..SL
1225
13 15 13 -0,016-0,034 15 +0,018
+0PTC..SL
1310PTC..SL
1320
14 16 14 -0,016-0,034 16 +0,018
+0PTC..SL
1410PTC..SL
1412PTC..SL
1415PTC..SL
1420PTC..SL
1425
15 17 15 -0,016-0,034 17 +0,018
+0PTC..SL
1510PTC..SL
1512PTC..SL
1515PTC..SL
1520PTC..SL
1525
16 18 16 -0,016-0,034 18 +0,018
+0PTC..SL
1610PTC..SL
1612PTC..SL
1615PTC..SL
1620PTC..SL
1625
17 19 17 -0,016-0,034 19 +0,021
+0PTC..SL
1710PTC..SL
1715PTC..SL
1720
18 20 18 -0,016-0,034 20 +0,021
+0PTC..SL
1810PTC..SL
1812PTC..SL
1815PTC..SL
1820PTC..SL
1825
20 23 20 -0,020-0,041 23 +0,021
+0
1,475 1,505 0,8 0,4
PTC..SL2010
PTC..SL2012
PTC..SL2015
PTC..SL2020
PTC..SL2025
PTC..SL2030
22 25 22 -0,020-0,041 25 +0,021
+0PTC..SL
2210PTC..SL
2212PTC..SL
2215PTC..SL
2220PTC..SL
2225PTC..SL
2230
24 27 24 -0,020-0,041 27 +0,021
+0PTC..SL
2415PTC..SL
2420PTC..SL
2425PTC..SL
2430
25 28 25 -0,020-0,041 28 +0,021
+0PTC..SL
2512PTC..SL
2515PTC..SL
2520PTC..SL
2525PTC..SL
2530PTC..SL
2540PTC..SL
2550
28 32 28 -0,020-0,041 32 +0,025
+0
1,970 2,005 1 0,6
PTC..SL2815
PTC..SL2820
PTC..SL2825
PTC..SL2830
PTC..SL2840
30 34 30 -0,020-0,041 34 +0,025
+0PTC..SL
3012PTC..SL
3015PTC..SL
3020PTC..SL
3025PTC..SL
3030PTC..SL
3040
32 36 32 -0,025-0,050 36 +0,025
+0PTC..SL
3220PTC..SL
3230PTC..SL
3240
35 39 35 -0,025-0,050 39 +0,025
+0PTC..SL
3512PTC..SL
3515PTC..SL
3520PTC..SL
3525PTC..SL
3530PTC..SL
3540PTC..SL
3550
38 42 38 -0,025-0,050 42 +0,025
+0PTC..SL
3815PTC..SL
3830PTC..SL
3840
40 44 40 -0,025-0,050 44 +0,025
+0PTC..SL
4012PTC..SL
4020PTC..SL
4025PTC..SL
4030PTC..SL
4040PTC..SL
4050
L
d DSplit f 2
f 1
min.o,3
45°± 5°
20°± 5°
DetailA DetailA
Unit: mm
PTC..SL cilindriche PTC..SL cylindric
Metrico Metric standard
9
d D AlberoShaft
f7
SedeHousing
H7
PareteWall
min/maxf1 f2
SIGLADesignation
L 0 / -0.4
20 25 30 40 50 60 70 80 100 115
45 50 45 -0,025-0,050 50 +0,025
+0
2,460 2,505 1,2 0,8
PTC..SL4520
PTC..SL4525
PTC..SL4530
PTC..SL4540
PTC..SL4550
50 55 50 -0,025-0,050 55 +0,030
+0PTC..SL
5020PTC..SL
5030PTC..SL
5040PTC..SL
5050PTC..SL
5060
55 60 55 -0,030-0,060 60 +0,030
+0PTC..SL
5530PTC..SL
5540PTC..SL
5550PTC..SL
5560
60 65 60 -0,030-0,060 65 +0,030
+0PTC..SL
6030PTC..SL
6040PTC..SL
6050PTC..SL
6060PTC..SL
6070
65 70 65 -0,030-0,060 70 +0,030
+0PTC..SL
6530PTC..SL
6540PTC..SL
6550PTC..SL
6560PTC..SL
6570
70 75 70 -0,030-0,060 75 +0,030
+0PTC..SL
7040PTC..SL
7050PTC..SL
7060PTC..SL
7070PTC..SL
7080
75 80 75 -0,030-0,060 80 +0,030
+0PTC..SL
7530PTC..SL
7540PTC..SL
7550PTC..SL
7560PTC..SL
7570PTC..SL
7580
80 85 80 0-0,030 85 +0,035
+0
2,440 2,490 1,4 0,8
PTC..SL8040
PTC..SL8050
PTC..SL8060
PTC..SL8070
PTC..SL8080
PTC..SL80100
85 90 85 0-0,035 90 +0,035
+0PTC..SL
8540PTC..SL
8560PTC..SL
8580PTC..SL85100
90 95 90 0-0,035 95 +0,035
+0PTC..SL
9040PTC..SL
9050PTC..SL
9060PTC..SL
9080PTC..SL90100
95 100 95 0-0,035 100 +0,035
+0PTC..SL
9550PTC..SL
9560PTC..SL
9580PTC..SL95100
100 105 100 0-0,035 105 +0,035
+0PTC..SL10050
PTC..SL10060
PTC..SL10080
PTC..SL100115
105 110 105 0-0,035 110 +0,035
+0PTC..SL10560
PTC..SL10580
PTC..SL105115
110 115 110 0-0,035 115 +0,035
+0PTC..SL11060
PTC..SL11080
PTC..SL110115
115 120 115 0-0,035 120 +0,035
+0
2,415 2,465 1,4 0,8
PTC..SL11560
PTC..SL11580
PTC..SL115115
120 125 120 0-0,035 125 +0,040
+0PTC..SL12060
PTC..SL12080
PTC..SL120100
125 130 125 0-0,040 130 +0,040
+0PTC..SL12560
PTC..SL125100
PTC..SL125115
130 135 130 0-0,040 135 +0,040
+0PTC..SL13060
PTC..SL13080
PTC..SL130100
140 145 140 0-0,040 145 +0,040
+0PTC..SL14060
PTC..SL14080
PTC..SL140100
150 155 150 0-0,040 155 +0,040
+0PTC..SL15060
PTC..SL15080
PTC..SL150100
160 165 160 0-0,040 165 +0,040
+0PTC..SL160100
180 185 180 0-0,040 185 +0,046
+0PTC..SL180100
190 195 190 0-0,046 195 +0,046
+0PTC..SL190100
200 205 200 0-0,046 205 +0,046
+0PTC..SL200100
220 225 220 0-0,046 225 +0,046
+0PTC..SL220100
250 255 250 0-0,046 255 +0,052
+0PTC..SL250100
260 265 260 0-0,052 265 +0,052
+0PTC..SL260100
280 285 280 0-0,052 285 +0,052
+0PTC..SL280100
300 305 300 0-0,052 305 +0,052
+0PTC..SL300100
PTC..SL cilindriche PTC..SL cylindric
Metrico Metric standard
Unit: mm
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTA O CON NASTRO AVVOLTO AL CONTRARIO CAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST OR WITH PTFE WRAPPED OUTSIDE
10
Split
L
d 3 d 1 d 2
R1 ± 0.51
35°± 5°f 2
f 1
min.o,3
20°± 5°
DetailA DetailA
Unit: mm
PTF..SL flangiate PTF..SL flanged
Metrico Metric standard
d1 d2 d3±0.5
AlberoShaft
f7
SedeHousing
H7
l10
-0,2f1 f2
SIGLADesignation
L ±0.25
4 5,5 7/7,5 8 9/9,5 11.5 12 16/16,5 17 21,5/22 26 31 41
6 8 12 6 -0,01-0,022 8 +0,015
+0
1 0,5 0,3
PTF..SL6040
PTF..SL6070
PTF..SL6080
8 10 15 8 -0,013-0,028 10 +0,015
+0PTF..SL
8055PTF..SL
8075PTF..SL
8095
10 12 18 10 -0,013-0,028 12 +0,018
+0PTF..SL10070
PTF..SL10090
PTF..SL10120
PTF..SL10170
12 14 20 12 -0,016-0,034 14 +0,018
+0PTF..SL12070
PTF..SL12090
PTF..SL12120
PTF..SL12170
14 16 22 14 -0,016-0,034 16 +0,018
+0PTF..SL14120
PTF..SL14170
15 17 23 15 -0,016-0,034 17 +0,018
+0PTF..SL15090
PTF..SL15120
PTF..SL15170
16 18 24 16 -0,016-0,034 18 +0,018
+0PTF..SL16120
PTF..SL16170
18 20 26 18 -0,016-0,034 20 +0,021
+0PTF..SL18120
PTF..SL18170
PTF..SL18220
20 23 30 20 -0,020-0,041 23 +0,021
+0
1,5 0,8 0,4
PTF..SL20115
PTF..SL20165
PTF..SL20215
22 25 32 22 -0,020-0,041 25 +0,021
+0PTF..SL22115
PTF..SL22165
PTF..SL22215
24 27 34 24 -0,020-0,041 27 +0,021
+0PTF..SL24165
PTF..SL24215
25 28 35 25 -0,020-0,041 28 +0,021
+0PTF..SL25115
PTF..SL25165
PTF..SL25215
28 32 40 28 -0,020-0,041 32 +0,025
+0
2 1 0,6
PTF..SL28220
30 34 42 30 -0,020-0,041 34 +0,025
+0PTF..SL30160
PTF..SL30260
32 36 44 32 -0,025-0,050 36 +0,025
+0PTF..SL32220
35 39 47 35 -0,025-0,050 39 +0,025
+0PTF..SL35160
PTF..SL35260
38 42 51 38 -0,025-0,050 42 +0,025
+0PTF..SL38310
40 44 53 40 -0,025-0,050 44 +0,025
0+PTF..SL40260
PTF..SL40310
PTF..SL40410
50 55 65 50 -0,025-0,050 55 +0,030
+02,5 1,2 0,8
PTF..SL50310
PTF..SL50410
60 65 75 60 -0,030-0,060 65 +0,030
+0PTF..SL60310
PTF..SL60410
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
11
PTW..SL ralle PTW..SL thrust washer
Metrico Metric standard
SIGLADesignation
Misure ralla / Washer size Installazione / Installation size
d0,25
D-0,25
T-0,05
M±0,125
h+0,4/+0,1
t±0,2
D10,12
PTW 10 SL 10 20
1,5
151,5
1
20PTW 12 SL 12 24 18 24PTW 14 SL 14 26 20
226
PTW 16 SL 16 30 23 30PTW 18 SL 18 32 25 32PTW 20 SL 20 36 28
3
36PTW 22 SL 22 38 30 38PTW 24 SL 24 42 33 42PTW 26 SL 26 44 35 44PTW 28 SL 28 48 38
4
48PTW 32 SL 32 54 43 54PTW 38 SL 38 62 50 62PTW 42 SL 42 66 54 66PTW 48 SL 48 74
2
61
1,5
74PTW 52 SL 52 78 65 78
PTW 62 SL 62 90 76 90
PTS..SL nastri PTS..SL strips
Unit: mm
Metrico Metric standard
SIGLA DIMENSIONI / Dimensions
Designation Spessore / Thickness Larghezza / Windth Largh. Utile / Usefull w. Lunghezza / Lenght
T B B1 L
PTS 1x140x1000 SL 1,0 0/-0,04 140 133 1000
PTS 1,5x140x1000 SL 1,5 0/-0,04 140 133 1000
PTS 2x170x1000 SL 2,0 0/-0,04 170 165 1000
PTS 2,5x170x1000 SL 2,5 0/-0,04 170 165 1000
PTS 3x170x500 SL 3,06 0/-0,04 170 165 500
12
CARATTERISTICHE
I cuscinetti a strisciamento in POM si possono considerare pre-lubrificati in quanto necessitano solo di una minima quantità di lubrificante per lavorare a lungo in modo soddisfacente.Presentano le medesime caratteristiche della versione SL ed ulteriormente:
• Possiedono un basso tasso di usura• Interessanti proprietà antifrizione• Notevole possibilità di PV• Sono idonei per carichi con urti
MATERIALE
Sono costituiti da un’armatura in acciaio a bas-so tenore di carbonio che conferisce resistenza meccanica e rivestiti esternamente con 2µm di rame o altro trattamento di protezione. Lo strato di bronzo poroso sinterizzato viene impregnato e rivestito di POM (o PEEK) sulla cui superficie ven-gono ricavati degli alveoli con lo scopo di conte-nere il grasso e raccogliere eventuali impurità che si dovessero interporre tra l’albero e la boccola.
Dove le lavorazioni meccaniche della sede e/o dell’albero non sono particolarmente precise si evidenzia la versione RKT. Questa, presentando del sovramateriale rispetto allo standard, può es-sere ripresa internamente mediante un’accurata lavorazione, permettendo così di evitare eventu-ali imperfezioni che potrebbero influire negativa-mente sulle proprietà tribologiche della boccola.Pertanto sono consigliati i seguenti processi di lavorazione, tornitura e foratura con:
• Taglio a secco• Velocità di taglio da 100 a 150 m/min• Avanzamento 0,05 mm/giro• Profondità di passata 0,1 mm• Utensile in metallo duro
LUBRIFICAZIONE
Il materiale utilizzato per questo tipo di boccola richiede scarsa manutenzione, dev’essere lubrificato inizialmente con grasso e non è necessario rilubrificare, tuttavia la presenza o l’alimentazione continua di un lubrificante ne prolunga notevolmente la durata. APPLICAZIONI
Questo tipo di cuscinetto radente è idoneo per applicazioni con scarsa manutenzione e condizioni di lavoro severe.Particolarmente adatto a movimenti di rotazione ed oscillanti, ha una limitata sensibilità al carico sugli spigoli ed è idrorepellente.Ha un buon comportamento smorzante che lo rende insensibile agli urti.Gli alveoli presenti sulla superficie lo rendono ideale per quelle applicazioni operanti in ambienti sporchi e dove non c’è la possibilità di lubrificare in modo continuativo o frequente (Es. macchine agricole, edili e movimentazioni in genere).
MONTAGGIO
Per il montaggio valgono le stesse condizioni indicate per le boccole autolubrificanti salvo il fatto che si possono utilizzare alberi con durezza che va da 150 a 600 HB con tolleranza h8 e rugosità fino a 0,8 µm.
Caratteristiche U.M. PT..RKCarico ammissibile (din./stat.) N/mm2 120/250
Resistenza a compressione N/mm2 380
Velocità di strisc. ammissibile m/s 2
Coeff. di attrito µ - 0,04 ÷ 0,12
Campo di temperature °C -40 ÷ +110
PVmax N/mm2 x m/s 2,8
BOCCOLE RILUBRIFICABILImultistrato con POM (o PEEK composito su richiesta)
Serie PT..RK
13
FEATURES
Suitable for rotating and oscillating movement, less maintenance requirements due to the long re-lubrication intervals, lower wear, lower susceptibility to edge loading, no absorption of water and therefore no swelling, good damping behaviours, good resistance to shock loads.
STRUCTURE
POM thickness 0.30~0.50 mm, it provides high wear resistance and low friction even with only little volume of lubricant are supplied, this bushing surface carries a pattern of circular indents which should be filled with grease on assembly of the bushing.Sintered bronze powder thickness 0.20-0.35mm, provides max. thermal conductivity away from the bushing surface, also serves as a reservoir for the resin mixture.
Low-carbon steel, provides exceptionally high load carrying capacity, excellent heat dissipation.Copper/Tin plating thickness 0.002mm, provides good corrosion resistance.
TYPICAL APPLICATIONS
Recommended for applications involving intermittent operation or boundary lubrication... Automotive: suspension joints, kingpin assemblies and stub axles of tucks, automobile driving joint hinges, steering and other linkages, articulation joints, rear chassis hinges, fair leader rollers..
STRUTTURA Il materiale di strisciamento “RK” richiedente poca manutenzione è disponibile in due varianti:
• pronto per il montaggio (RK)• con sovramateriale (RKT)
Versione “RK”
La versione “RK” consta di tre strati:
• armatura in acciaio• strato di bronzo poroso• strato di strisciamento
Sull’armatura in acciaio viene sinterizzato uno strato di bronzo poroso con spessore da 0,2 mm a 0,35 mm. Durante la fase di laminazione i pori dello strato di bronzo poroso vengono riempiti con una miscela di PEEK o resina acetalica (POM).Dopo tale trattamento sul bronzo sinterizzato rimane uno strato di scorrimento nel quale vengono realizzati gli alveoli per il lubrificante.
Versione “RKT”
La versione “RKT” ha la stessa struttura del versione precedente però lo strato di strisciamento è in media più spesso di 0,15 mm. Ciò rende possibile una successiva lavorazione della superficie per pareggiare disallineamenti o per giochi con tolleranze più ristrette.
Versioni “RK3 - RKT3”
La versione speciale “3” viene fornita su richiesta. Questa struttura si differenzia dalle precedenti in quanto lo strato di strisciamento è privo di alveoli per la lubrificazione.
POM o PEEK
Alveolo per lubrificazione
PT..RK seriesRELUBRICATING BUSHINGS multilayer with POM (or composite PEEK on demand)
Strato di bronzo
Armatura in acciaio Protezione superficiale
14
Unit: mm
PTC..RK cilindriche PTC..RK cylindric
Metrico Metric standard
d DAlberoShaft
f7
SedeHousing
H7
PareteWallmin/max
f1 f2
SIGLADesignation
L 0 / -0,410 12 15 20 25 30 40 50 60 70 80 100/115
10 12 10 -0,013-0,028 12 0,018
0
0,980,955 0,5 0,3
PTC..RK 1010
PTC..RK 1012
PTC..RK 1015
PTC..RK 1020
12 14 12 -0,016-0,034 14 0,018
0PTC..RK
1210PTC..RK
1212PTC..RK
1215PTC..RK
1220PTC..RK
1225
14 16 14 -0,016-0,034 16 0,018
0PTC..RK
1410PTC..RK
1412PTC..RK
1415PTC..RK
1420PTC..RK
1425
15 17 15 -0,016-0,034 17 0,018
0PTC..RK
1510PTC..RK
1512PTC..RK
1515PTC..RK
1520PTC..RK
1525
16 18 16 -0,016-0,034 18 0,018
0PTC..RK
1610PTC..RK
1612PTC..RK
1615PTC..RK
1620PTC..RK
1625
18 20 18 -0,016-0,034 20 0,021
0PTC..RK
1810PTC..RK
1812PTC..RK
1815PTC..RK
1820PTC..RK
1825
20 23 20 -0,02-0,041 23 0,021
0
1,4751,445 0,8 0,4
PTC..RK 2010
PTC..RK 2015
PTC..RK 2020
PTC..RK 2025
PTC..RK 2030
22 25 22 -0,02-0,041 25 0,021
0PTC..RK
2210PTC..RK
2215PTC..RK
2220PTC..RK
2225PTC..RK
2230
24 27 24 -0,02-0,041 27 0,021
0PTC..RK
2420PTC..RK
2430
25 28 25 -0,02-0,041 28 0,021
0PTC..RK
2515 PTC..RK
2520 PTC..RK
2525 PTC..RK
2530 PTC..RK
2540 PTC..RK
2550
28 32 28 -0,02-0,041 32 0,025
0
1,971,935 1 0,6
PTC..RK 2820
PTC..RK 2830
30 34 30 -0,02-0,041 34 0,025
0PTC..RK
3015PTC..RK
3020PTC..RK
3025PTC..RK
3030PTC..RK
3040PTC..RK
3050
35 39 35 -0,025-0,05 39 0,025
0PTC..RK
3515PTC..RK
3520PTC..RK
3525PTC..RK
3530PTC..RK
3540PTC..RK
3550
40 44 40 -0,025-0,05 44 0,025
0PTC..RK
4020PTC..RK
4025PTC..RK
4030PTC..RK
4040PTC..RK
4050
45 50 45 -0,025-0,05 50 0,025
0
2,462,415 1,2 0,8
PTC..RK 4520
PTC..RK 4530
PTC..RK 4540
PTC..RK 4550
50 55 50 -0,025-0,05 55 +0,030
0PTC..RK
5030 PTC..RK
5040PTC..RK
5050PTC..RK
5060
55 60 55 -0,03-0,06 60 +0,030
0PTC..RK
5530PTC..RK
5540PTC..RK
5550PTC..RK
5560
60 65 60 -0,03-0,06 65 +0,030
0PTC..RK
6030PTC..RK
6040PTC..RK
6050PTC..RK
6060PTC..RK
6070
65 70 65 -0,03-0,06 70 +0,030
0PTC..RK
6550PTC..RK
6570
70 75 70 -0,03-0,06 75 +0,030
0PTC..RK
7040PTC..RK
7050PTC..RK
7060PTC..RK
7080
75 80 75 -0,03-0,06 80 +0,030
0PTC..RK
7550PTC..RK
7560PTC..RK
7580
80 85 80 0-0,03 85 0,035
0
2,452,385 1,4 0,8
PTC..RK 8040
PTC..RK 8050
PTC..RK 8060
PTC..RK 80100
85 90 85 0-0,035 90 0,035
0PTC..RK
8540PTC..RK
8560PTC..RK
85100
90 95 90 0-0,035 95 0,035
0PTC..RK
9060PTC..RK
90100
100 105 100 0-0,035 105 0,035
0PTC..RK
10060PTC..RK 100115
105 110 105 0-0,035 110 0,035
0PTC..RK 105115
110 115 110 0-0,035 115 0,035
0PTC..RK 110115
115 120 115 0-0,054 120 0,035
0PTC..RK 115100
120 125 120 0-0,035 125 +0,040
0PTC..RK 120100
125 130 125 0-0,04 130 +0,040
0PTC..RK 125100
130 135 130 0-0,04 135 +0,040
0PTC..RK 130100
140 145 140 0-0,04 145 +0,040
0PTC..RK 140100
150 155 150 0-0,04 155 +0,040
0PTC..RK 150100
160 165 160 0-0,04 165 0,04
0PTC..RK 160100
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
15
PTW..RK ralle PTW..RK thrust washer
Metrico Metric standard
SIGLADesignation
Misure ralla / Washer size Installazione / Installation size
d0,25
D-0,25
T-0,05
M±0,125
h+0,4/+0,1
t±0,2
D10,12
PTW 10 RK 10 20
1,5
151,5
1
20PTW 12 RK 12 24 18 24PTW 14 RK 14 26 20
226
PTW 16 RK 16 30 23 30PTW 18 RK 18 32 25 32PTW 20 RK 20 36 28
3
36PTW 22 RK 22 38 30 38PTW 24 RK 24 42 33 42PTW 26 RK 26 44 35 44PTW 28 RK 28 48 38
4
48PTW 32 RK 32 54 43 54PTW 38 RK 38 62 50 62PTW 42 RK 42 66 54 66PTW 48 RK 48 74
2
61
1,5
74PTW 52 RK 52 78 65 78
PTW 62 RK 62 90 76 90
PTS..RK nastri PTS..RK strips
Unit: mm
Metrico Metric standard
SIGLA DIMENSIONI / Dimensions
Designation Spessore / Thickness Larghezza / Windth Largh. Utile / Usefull w. Lunghezza / Lenght
T B B1 L
PTS 1X140X1000 RK 1,0 0/-0,04 140 133 1000
PTS 1,5X140X1000 RK 1,5 0/-0,04 140 133 1000
PTS 2X170X1000 RK 2,0 0/-0,04 170 165 1000
PTS 2,5X170X1000 RK 2,5 0/-0,04 170 165 1000
PTS 3X170X500 RK 3,06 0/-0,04 170 165 500
16
CARATTERISTICHE
I cuscinetti autolubrificanti sinterizzati sono ottenuti con i più moderni e avanzati processi nel campo della metallurgia delle polveri, presentando elevate caratteristiche meccaniche e tecnologiche.Hanno una struttura porosa controllata e sono impregnati di olio che viene rilasciato gradualmente durante il regolare funzionamento formando un film autolubrificante.Si può sostituire in tutto o in parte l’olio lubrificante con grafite che conferisce al prodotto un aspetto leggermente più asciutto e di tonalità più scura.La porosità utile è del 25-30% del suo volume ed è riempita con olio prescelto ma può essere abbassata fino al 18% al fine di aumentarne la resistenza meccanica nel caso di carichi statici molto elevati.Le polveri accuratamente miscelate vengono pressate e stampate per poi essere sinterizzate in forno, ad una temperatura più bassa del punto di fusione, ad atmosfera e temperatura controllata. Successivamente dopo la fase di calibratura sui diametri interno ed esterno, tramite un procedimento sotto vuoto le porosità dei particolari vengono saturate con olio.Infine i prodotti sinterizzati possono essere protetti
con rivestimenti galvanici, bruniti o ossidati a vapore o sottoposti a trattamenti termici.
LAVORAZIONI MECCANICHE
Qualsiasi lavorazione meccanica è sconsigliabile perché ne modificherebbe la struttura superficiale impedendo la fuoriuscita dell’olio. Tuttavia se una lavorazione non può essere evitata, si consiglia l’uso di utensili di metallo duro della stessa qualità usata per la lavorazione della ghisa, perfettamente affilati con spoglia frontale e laterale di circa 7°, lavorando con piccole passate e a piccoli avanzamenti ad un velocità di 100m/min’.
VANTAGGI
Le boccole sinterizzate offrono numerosi vantaggi quali:
• sono autolubrificanti ed esenti da manutenzione e lubrificazione esterna
• buone proprietà di attrito con velocità di strisciamento molto elevata
• si possono ottenere particolari a disegno anche complessi pronti per il montaggio
• il basso costo di produzione rende il prodotto molto economico
• sono generalmente adatte dove ci sono molti giri e pochi carichi.
U.M. Bronzo FerroComposizione - 90% Cu + 10% Sn 99% Fe
Carico statico Kg/cm2 200 450
Durezza HB 20 40
Coefficiente d'attrito - 0,030 0,025
Velocità massima m/s 6 4
Resistenza a trazione Kg/cm2 9 ÷ 18 18 ÷ 25
Campo di temperature °C -20 ÷ +300 -20 ÷ +300
PVmax Kg/cm2 x m/s 15,8 12,5
BOCCOLE IN BRONZO / FERRO SINTERIZZATO bronzo/bronzo+grafite/bronzo+MoS2/bronzo-ferro/ferro
Serie BZ.. / FE..
17
DESCRIPTION
The base material for sintered parts such as sliding bushings or other formed parts are iron, bronze, iron with bronze and other metal in powder form.
This powder is formed under high pressure in dies into a temperature which is just below the melting point.
According to the work condition, the bushings can impregnate with different oil or solid lubricants for the self-lubricating. Sintered self lubricating bushings are the ideal and economical solution for applications where lubrication is difficult or lubrication could not be applied.
FEATURES
• Good wear resistance with lower friction • Lower the material cost for large production • Can be machined again after installation if
possible• Lower maintenance requirement • High speed with lower noise• Different structures could be available
against special
TOLLERANZE La bronzina sinterizzata possiede le seguenti tolleranze standard costruttive:• Ø esterno r7• Ø interno F7 (a montaggio avvenuto la
tolleranza risulterà G7)• lunghezza h js13
standard montaggio:
• sede H7 L’albero deve avere una durezza possibilmente compresa tra 200 e 300 HB, una rugosità compresa tra 0,2 e 0,8 µm ed una tolleranza tra f7 ed f8. CONSERVAZIONE A MAGAZZINO Le boccole autolubrificanti devono essere conservate in ambiente asciutto ed esente da polvere.Bisogna assolutamente evitare di porle a contatto con sostanze in grado di esercitare un’azione assorbente come: carta, cartone, legno, ecc..
BZ.. / FE.. seriesBRONZE / IRON SINTERED BUSHINGS bronze/bronze+graphite/bronze+MoS2/bronze-iron/iron
MONTAGGIO
Il montaggio deve essere effettuato per interferenza nella sede a mezzo di un mandrino con spallamento e superficie rettificata per evitare danni alla boccola.Per consentire infine l’estrazione del mandrino è necessario un estrattore antisfilamento. La tolleranza del mandrino deve essere mantenuta nel campo m5.
18
Metrico Metric standard
BZ.. / FE.. cilindriche BZ.. / FE.. cylindric
DIMENSIONI DELLE BOCCOLE CILINDRICHE CYLINDRICAL BUSHINGS DIMENSIONS
3x6x4 8x12x10 12x16x23 16x21x16 22x28x30 35x45x50 3x6x5 8x12x12 12x16x30 16x21x21 22x28x40 40x50x40 3x6x6 8x12x14 12x17x12 16x21x30 25x30x20 40x50x50 3x6x8 8x12x16 12x17x17 16x22x16 25x30x25 40x50x60 3x8x6 8x14x8 12x17x24 16x22x22 25x30x30 45x55x45 4x8x4 8x14x14 12x18x12 16x22x25 25x30x35 45x55x55 4x8x8 8x14x16 12x18x18 16x22x30 25x30x40 45x55x60
4x8x10 8x16x8 12x18x25 18x24x18 25x32x25 45x55x65 4x8x12 8x16x10 14x18x14 18x24x24 25x32x32 50x60x50 4x10x4 8x16x16 14x18x15 18x24x28 25x32x35 50x60x60 4x10x10 8x16x18 14x18x18 18x24x30 25x32x40 50x60x70 4x10x12 8x16x25 14x18x19 18x24x40 25x35x15 55x70x75
5x8x8 10x13x10 14x18x22 18x25x18 25x35x25 60x70x25 5x8x10 10x13x12 14x18x26 18x25x25 25x35x35 60x70x50 5x9x5 10x13x18 14x20x14 18x25x30 25x35x40 60x70x60 5x9x9 10x14x10 14x20x15 18x25x36 25x35x50 60x70x70 5x9x11 10x14x14 14x20x20 20x23x20 30x35x25 60x70x80 5x10x5 10x14x15 14x20x25 20x23x24 30x35x30 60x75x60
5x10x10 10x14x18 14x20x28 20x24x20 30x35x35 60x75x75 5x10x12 10x14x20 14x20x30 20x24x24 30x35x40 60x75x80 5x10x14 10x15x10 15x20x12 20x24x30 30x38x30 70x80x70 5x12x5 10x15x15 15x20x15 20x25x15 30x38x38 70x80x80
5x12x12 10x15x20 15x20x20 20x25x20 30x38x45 70x80x90 5x12x14 10x16x10 15x20x24 20x25x22 30x38x50 80x95x70
6x8x8 10x16x15 15x20x25 20x25x25 30x40x25 80x95x80 6x10x6 10x16x16 15x20x28 20x25x28 30x40x30 80x95x90
6x10x10 10x16x20 15x20x40 20x25x34 30x40x40 85x100x100 6x10x12 10x16x25 15x21x15 20x25x40 30x40x50 90x100x90 6x10x14 12x14x16 15x21x21 20x26x20 35x40x30 90x100x100 6x12x6 12x15x7,5 15x21x30 20x26x26 35x40x35 100x120,3x65 6x12x12 12x15x8 15x22x15 20x26x30 35x40x40 100x120x90 6x12x15 12x15x12,8 15x22x22 20x26x40 35x40x45 120x130x65 6x12x25 12x15x15 15x22x30 20x28x20 35x42x35 140x155x25 6x14x6 12x15x18 16x20x15 20x28x28 35x42x42 140x155x65
6x14x12 12x16x12 16x20x16 20x28x40 35x42x50 160x175x50 6x14x14 12x16x15 16x20x20 20x30x20 35x45x25 6x14x16 12x16x16 16x20x28 22x28x22 35x45x35 8x12x8 12x16x20 16x20x30 22x28x28 35x45x45
Struttura del codice: BZ/FE 3 6 4Code structure:
DescrizioneDescription
Ø InternoØ Internal
Ø EsternoØ External
LunghezzaLength
Unit: mm
POSSONO ESSERE PRODOTTE BOCCOLE IN BZ O FERRO CON QUALSIASI DIMENSIONE A RICHIESTA BRONZE AND IRON BUSHINGS CAN BE PRODUCED IN ANY DIMENSION ON REQUEST
19
BZ.. / FE.. flangiate BZ.. / FE.. flanged
Metrico Metric standard
Struttura del codice:Code structure:
DIMENSIONI DELLE BOCCOLE FLANGIATE FLANGED BUSHINGS DIMENSIONS
5x10x12x2x7 9x14x18x3x20 13x18x20x2,5x13 16x22x28x4x32 25x32x40x5x40 35x45x55x5x45 5x10x12x2x12 10x14x18x3x10 14x20x25x3x12 17x25x32x4x17 25x35x45x5x25 35x45x55x5x50 5x10x12x2x20 10x14x18x3x14 14x20x25x3x14 17x25x32x4x25 25x35x45x5x35 38x45x55x5x38 6x12x14x2x8 10x14x18x3x20 14x20x25x3x20 17x25x32x4x35 25x35x45x5x45 38x45x55x5x45
6x12x14x2x13 10x15x19x2x20 14x20x25x3x25 18x25x32x4x18 28x40x50x5x28 40x50x60x6x40 6x12x14x2x20 10x16x20x3x10 15x20x24x2,5x12 18x25x32x4x25 28x40x50x5x40 40x50x60x6x50 7x12x16x2,5x8 10x16x20x3x16 15x20x24x2,5x17,5 18x25x32x4x35 28x40x50x5x50 40x50x60x6x60
7x12x16x2,5x14 10x16x20x3x20 15x20x24x2,5x30 20x28x35x4x20 30x35x40x3x30 45x55x65x6x45 7x12x16x2,5x20 12x16x20x2x12 15x22x28x3x15 20x28x35x4x25 30x35x40x3x35 45x55x65x6x55
8x14x18x3x8 12x16x20x2x16 15x22x28x3x22 20x28x35x4x35 30x40x50x5x30 45x55x65x6x65 8x14x18x3x14 12x16x20x2x25 15x22x28x3x30 22x32x40x5x40 30x40x50x5x42 50x60x70x6x50 8x14x18x3x20 12x18x22x3x12 16x22x28x3,5x16 25x30x40x4x16 30x40x50x5x55 50x60x70x6x60 9x14x18x3x9 12x18x22x3x18 16x22x28x3,5x22 25x32x40x5x25 35x45x55x5x25 50x60x70x6x70
9x14x18x3x14 12x18x22x3x25 16x22x28x3,5x30 25x32x40x5x32 35x45x55x5x35 60x75x85x6x60
BZ/FE 5 10 12
DescrizioneDescription
Ø InternoØ Internal
Ø EsternoØ External
2
Ø FlangiaØ Flange
Spessore flangiaFlange thickness
7
LunghezzaLength
Unit: mm
POSSONO ESSERE PRODOTTE BOCCOLE IN BZ O FERRO CON QUALSIASI DIMENSIONE A RICHIESTA BRONZE AND IRON BUSHINGS CAN BE PRODUCED IN ANY DIMENSION ON REQUEST
Esempi | Examples
20
CARATTERISTICHE
Questi tipi di elementi di scorrimento non necessitano di alcuna lubrificazione e sono adatti all’impiego con carichi gravosi e basse velocità.Sono costituiti da un corpo solido ( in lega di rame, acciaio o ghisa) con inserti di lubrificante solido a base di Ptfe e/o grafite.La grafite, durante il funzionamento crea una sottile pellicola che ricopre entrambe le superfici ed evita, in questo modo, il contatto diretto tra i metalli.
VANTAGGI
I principali vantaggi che offrono questi prodotti, sono:• alta capacità di carico statico e dinamico• ottime prestazioni sotto carico elevato con
movimenti intermittenti• autolubrificante ed esente da manutenzione• tollera comunque bene qualsiasi lubrificante
onvenzionale • basso coefficiente di attrito senza effetto stick-
slip poco sensibile allo sporco, resiste ai prodotti chimici e alla corrosione
• alta stabilità dimensionale in presenza di acqua, particolarmente adatto all’utilizzo in ambiente marino
• buona resistenza allo stress da impatto
• limitata sensibilità al carico sugli spigoli, può essere usato nei disassamenti
• assorbe bene le vibrazioni• si presta per usi a temperature medio alte• conduttore di elettricità, non evidenzia
fenomeni elettrostatici• alta conducibilità termica
MONTAGGIO E TOLLERANZE
Nel caso della boccola, il montaggio deve essere effettuato per interferenza a mezzo di un mandrino con spallamento e superficie rettificata oppure in alternativa raffreddando il particolare a temperature molto basse.La boccola autolubrificante con inserti in grafite possiede le seguenti tolleranze costruttive:
• Ø esterno m6 (r6 flangiate)• Ø interno F7 (E7 flangiate)• lunghezza -0,1/-0,3• Ø flangia +0,2/-0,2• spessore flangia 0/-0,1
La sede deve avere una tolleranza H7, mentre l’albero può avere delle tolleranze del tipo:
• “d8” per utilizzo con carichi elevati• “e7” per utilizzo con carichi leggeri• “f7” per un accoppiamento di precisioneLa durezza dell’albero dev’essere compresa tra i 180 HB e 250 HB e comunque superiore a quella dell’elemento di scorrimento, mentre la rugosità dev’essere compresa tra 0,2 e 0,8 µm.
Serie BG../AG../CG..ELEMENTI AUTOLUBRIFICANTI A SECCOcon inserti di lubrificante solido
Ns codice Tipo di materiale Durezza HB
C. attrito µ
Temp. Limite a secco
°C
C max N/mm2
PV max N/mm2●m/s
Vel. max m/s
a secco / dry lubrificata /lubricated
BG..A CuZn25Al6FeMn3 210 -250 0,03 ~ 0,20 -40 / +300 100 3,4 0,25 0,5BG..B CuPb5Sn5Zn5 80 -120 0,03 ~ 0,18 -40 / +460 60 3,4 0,2 0,4BG..D CuSn12 >80 0,03 ~ 0,18 -40 /+400 70 3,4 0,2 0,4BG..E CuAl10Fe3 >150 0,03 ~ 0,20 -40 / +400 50 3,4 0,35 0,70BG..S CuZn25Al6FeMn3 >250 0,03 ~ 0,20 -40 / +300 150 3,4 0,20 0,40CG.. ASTM Classe40 – HT 250 >160 < 0,17 -40 / +400 70 1,7 0,15 0,25
Ns codice Tipo di materiale Durezza HRC
C. attrito µ
Temp. Limite a secco
°C
C max N/mm2
PV max N/mm2●m/s
Vel. max m/s
a secco / dry lubrificata /lubricated
AG.. GCr15 (100Cr6) HRC>60 <0,17 350 200 2,5 0,15 0,25
TABELLA DEI MATERIALI
21
BG../AG../CG.. seriesSELF LUBRICATING DRY ELEMENTS with solid lubricant insert
FEATURES
• Long-term use without maintenance;• Designed for high static load and dynamic load;• Has a low coefficient of friction and smooth, no “sticky” phenomenon;• Resistant to dust, corrosion resistance, impact resistance and resistance to edge load capacity;• Metal substrate has good shock absorption;• Be able in a wide temperature range;• Suitable for reciprocating, rotary and oscillating so frequent and difficult to form a film starts the occasion;• Has a very low wear rate, long service life.
STRUCTURE
BG material is made of strong cast bronze based metal with special solid lubricants embedded. The base metal withstands high load and the solid lubricants provide self-lubrication. The bushing shows excellent performance without pre-lubrication under conditions of extreme high/low temperature with low speed. This material provides a maintenance-free bushing solution, particularly for high load, intermittent of oscillating motion.
STRUTTURA
Versione “BG..”
Sono costituite da metallo basato su bronzo massiccio con inserito uno speciale lubrificante solido. La base di bronzo resiste a forti carichi e il lubrificante solido provvede alla auto-lubrificazione. La boccola mostra eccellenti caratteristiche anche senza la pre-lubrificazione, sotto condizioni di temperature estremamente alte/basse ma a basse velocità.Questo materiale si presta alle soluzioni delle boccole esenti da manutenzione, particolarmente per forti carichi, e movimento oscillante intermittente.
APPLICAZIONI
Versione “BG..A”
Prodotto base multiuso, adatto per molteplici circostanze inclusi alti e bassi carichi, alte e basse temperature, con lubrificazione ad olio o a secco, o eventualmente in acqua. Con la sua struttura fatta di ottone ad alta resistenza, una durezza doppia rispetto alle normali boccole ed un grado di resistenza all’usura ulteriormente ottimizzato, può essere utilizzato per l’industria metallurgica ed automatica. Inoltre si presta nelle macchine per iniezioni plastiche, negli interrutori automatici dell’alta tensione, pulegge, stampi, parti striscianti per il varo delle navi, ecc..
Versione “BG..B”
I prodotti della serie BG..B sono adottati principalmente per situazioni di basso carico e alte temperature, per esempio attrezzature e macchinari per l’industria leggera, o in prossimità di lavorazioni a fuoco.
Versione “CG..”
Questa serie si propone come alternativa nelle situazioni di carichi non gravosi e quindi la possibilità di utilizzare prodotti ad un costo
inferiore. Possono quindi rispondere alla richiesta di applicazioni quali: guide per stampi, nastri trasportatori e così di seguito.
Versione “AG..”
I prodotti di questa serie sono una speciale tipologia di boccole ad alta resistenza meccanica in acciao 100Cr6. Grazie alle loro eccellenti capacità complessive, sono specialmente adatte per le parti di supporto su macchine con carichi gravosi, per esempio: sostegni per gru, supporti per montacarichi ecc..Data la loro struttura di acciaio, non sono adatte per attività in condizioni d’acqua, acidi o alcalini.
Ns codice Composizione Caratteristiche Applicazioni Temp. max
X1 Grafite + addittivi Eccellente resistenza ai prodotti chimici e basso attrito usi generici 400 °CX2 PTFE+MoS2+CF Basso coefficiente d'attrito e ottimo per utilizzo in acqua turbine , navali, ecc. 300 °C
TABELLA DEI LUBRIFICANTI
22
Metrico Metric standard
BGC../AGC.. cilindriche BGC../AGC.. cylindric
Unit: mm
dF7
Dm6
AlberoShaft
SedeHousing
H7
PareteWall
min/max
SIGLADesignation
L -0.1 / -0.3
8 10 12 15 16 20 25 30 35 40 50 60 70 80
8 12 8 12
+0.018 +0.007
BGC/AGC81208
BGC/AGC81210
BGC/AGC81212
BGC/AGC81215
10 14 10 14 BGC/AGC101408
BGC/AGC101410
BGC/AGC101412
BGC/AGC101415
BGC/AGC101420
12 18 12 18 BGC/AGC121810
BGC/AGC121812
BGC/AGC121815
BGC/AGC121816
BGC/AGC121820
BGC/AGC121825
BGC/AGC121830
13 19 13 19
+0.021 +0.008
BGC/AGC131910
BGC/AGC131915
BGC/AGC131916
14 20 14 20 BGC/AGC142010
BGC/AGC142012
BGC/AGC142015
BGC/AGC142020
BGC/AGC142025
BGC/AGC142030
15 21 15 21 BGC/AGC152110
BGC/AGC152112
BGC/AGC152115
BGC/AGC152116
BGC/AGC152120
BGC/AGC152125
BGC/AGC152130
16 22 16 22 BGC/AGC162210
BGC/AGC162212
BGC/AGC162215
BGC/AGC162216
BGC/AGC162220
BGC/AGC162225
BGC/AGC162230
BGC/AGC162235
BGC/AGC162240
18 24 18 24 BGC/AGC182412
BGC/AGC182415
BGC/AGC182416
BGC/AGC182420
BGC/AGC182425
BGC/AGC182430
BGC/AGC182435
BGC/AGC182440
20 28 20 28 BGC/AGC202810
BGC/AGC202812
BGC/AGC202815
BGC/AGC202816
BGC/AGC202820
BGC/AGC202825
BGC/AGC202830
BGC/AGC202835
BGC/AGC202840
BGC/AGC202850
22 32 22 32
+0.025 +0.009
BGC/AGC223212
BGC/AGC223215
BGC/AGC223220
BGC/AGC223225
25 33 25 33 BGC/AGC253312
BGC/AGC253315
BGC/AGC253316
BGC/AGC253320
BGC/AGC253325
BGC/AGC253330
BGC/AGC253335
BGC/AGC253340
BGC/AGC253350
BGC/AGC253360
30 38 30 38 BGC/AGC303812
BGC/AGC303815
BGC/AGC303820
BGC/AGC303825
BGC/AGC303830
BGC/AGC303835
BGC/AGC303840
BGC/AGC303850
BGC/AGC303860
35 45 35 45 BGC/AGC354520
BGC/AGC354525
BGC/AGC354530
BGC/AGC354535
BGC/AGC354540
BGC/AGC354550
BGC/AGC354560
40 50 40 50 BGC/AGC405020
BGC/AGC405025
BGC/AGC405030
BGC/AGC405035
BGC/AGC405040
BGC/AGC405050
BGC/AGC405060
BGC/AGC405070
BGC/AGC405080
45 55 45 55+0.030 +0.011
BGC/AGC455530
BGC/AGC455535
BGC/AGC455540
BGC/AGC455550
BGC/AGC455560
50 60 50 60 BGC/AGC506030
BGC/AGC506035
BGC/AGC506040
BGC/AGC506050
BGC/AGC506060
BGC/AGC506070
BGC/AGC506080
BGC
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
23
Metrico Metric standard
Unit: mm
dF7
Dm6
AlberoShaft
SedeHousing
H7
PareteWall
min/max
SIGLADesignation
L -0.1 / -0.3
30 35 40 50 60 70 80 100 120 130 140 150
50 62 50 62
+0.030+0.011
BGC/AGC506230
BGC/AGC506235
BGC/AGC506240
BGC/AGC506250
BGC/AGC506260
BGC/AGC506270
50 65 50 65 BGC/AGC506530
BGC/AGC506540
BGC/AGC506550
BGC/AGC506560
BGC/AGC506570
BGC/AGC506580
BGC/AGC5065100
55 70 55 70 BGC/AGC557040
BGC/AGC557050
BGC/AGC557060
BGC/AGC557070
60 74 60 74 BGC/AGC607430
BGC/AGC607435
BGC/AGC607440
BGC/AGC607450
BGC/AGC607460
BGC/AGC607470
BGC/AGC607480
60 75 60 75 BGC/AGC607530
BGC/AGC607535
BGC/AGC607540
BGC/AGC607550
BGC/AGC607560
BGC/AGC607570
BGC/AGC607580
BGC/AGC6075100
63 75 63 75 BGC/AGC637560
BGC/AGC637570
BGC/AGC637580
65 80 65 80 BGC/AGC658050
BGC/AGC658060
BGC/AGC658070
BGC/AGC658080
70 85 70 85
+0.035 +0.013
BGC/AGC708535
BGC/AGC708540
BGC/AGC708550
BGC/AGC708560
BGC/AGC708570
BGC/AGC708580
BGC/AGC7085100
70 90 70 90 BGC/AGC709050
BGC/AGC709060
BGC/AGC709070
BGC/AGC709080
BGC/AGC7090100
BGC/AGC7090120
BGC/AGC7090130
BGC/AGC7090140
75 90 75 90 BGC/AGC759060
BGC/AGC759070
BGC/AGC759080
BGC/AGC7590100
75 95 75 95 BGC/AGC759560
BGC/AGC759570
BGC/AGC759580
BGC/AGC7595100
80 96 80 96 BGC/AGC809640
BGC/AGC809650
BGC/AGC809660
BGC/AGC809670
BGC/AGC809680
BGC/AGC8096100
BGC/AGC8096120
80 100 80 100 BGC/AGC8010040
BGC/AGC8010050
BGC/AGC8010060
BGC/AGC8010070
BGC/AGC8010080
BGC/AGC80100100
BGC/AGC80100120
BGC/AGC80100140
90 110 90 110 BGC/AGC9011030
BGC/AGC9011050
BGC/AGC9011060
BGC/AGC9011070
BGC/AGC9011080
BGC/AGC90110100
BGC/AGC90110120
100 120 100 120
+0.040+0.015
BGC/AGC10012060
BGC/AGC10012070
BGC/AGC10012080
BGC/AGC100120100
BGC/AGC100120120
BGC/AGC100120140
110 130 110 130 BGC/AGC11013080
BGC/AGC110130100
BGC/AGC110130120
120 140 120 140 BGC/AGC12014080
BGC/AGC120140100
BGC/AGC120140120
BGC/AGC120140140
125 145 125 145 BGC/AGC125145100
BGC/AGC125145120
130 150 130 150 BGC/AGC130150100
BGC/AGC130150130
140 160 140 160 BGC/AGC140160100
BGC/AGC140160140
150 170 150 170 BGC/AGC150170100
BGC/AGC150170150
160 180 160 180 BGC/AGC160180100
BGC/AGC160180150
BGC../AGC.. cilindriche BGC../AGC.. cylindric
AGC
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
24
Metrico Metric standard
BGF../AGF.. flangiate BGF../AGF.. flanged
dE7
Dr6
AlberoShaft
SedeHousing
H7
PareteWall
min/maxF L1
- 0.10
SIGLADesignation
L -0.1 / -0.3
15 20 25 30 35 40 50 60 80 100
10 14 10 14+0.034 +0.023
22 2 BGF/AGF101422215
BGF/AGF101422220
12 18 12 18 25
3
BGF/AGF121825315
BGF/AGF121825320
13 19 13 19
+0.041 +0.028
26 BGF/AGF131926315
BGF/AGF131926320
14 20 14 20 27 BGF/AGF142027315
BGF/AGF142027320
15 21 15 21 28 BGF/AGF152128315
BGF/AGF152128320
BGF/AGF152128325
BGF/AGF152128330
16 22 16 22 29 BGF/AGF162229315
BGF/AGF162229320
BGF/AGF162229325
BGF/AGF162229330
20 30 20 30 40
5
BGF/AGF203040515
BGF/AGF203040520
BGF/AGF203040525
BGF/AGF203040530
BGF/AGF203040540
25 35 25 35
+0.050 +0.034
45 BGF/AGF253545515
BGF/AGF253545520
BGF/AGF253545525
BGF/AGF253545530
BGF/AGF253545540
30 40 30 40 50 BGF/AGF304050520
BGF/AGF304050525
BGF/AGF304050530
BGF/AGF304050535
BGF/AGF304050540
BGF/AGF304050550
31.5 40 31.5 40 50 BGF/AGF31.54050520
BGF/AGF31.54050535
35 45 35 45 60 BGF/AGF354560520
BGF/AGF354560530
BGF/AGF354560540
BGF/AGF354560550
40 50 40 50 65 BGF/AGF405065520
BGF/AGF405065530
BGF/AGF405065540
BGF/AGF405065550
45 55 45 55
+0.060 +0.041
70 BGF/AGF455570530
BGF/AGF455570540
BGF/AGF455570550
BGF/AGF455570560
50 60 50 60 75 BGF/AGF506075530
BGF/AGF506075540
BGF/AGF506075550
BGF/AGF506075560
55 65 55 65 80 BGF/AGF556580540
BGF/AGF556580550
BGF/AGF556580560
60 75 60 75+0.062 +0.043
90
7.5
BGF/AGF6075907.540
BGF/AGF6075907.550
BGF/AGF6075907.580
63 75 63 75 85 BGF/AGF6375857.580
70 85 70 85
+0.073 +0.051
105 BGF/AGF70851057.550
BGF/AGF70851057.580
75 90 75 90 110 BGF/AGF75901107.560
80 100 80 100 120
10
BGF/AGF801001201060
BGF/AGF801001201080
BGF/AGF8010012010100
90 110 90 110+0.076 +0.054
130 BGF/AGF901101301060
BGF/AGF901101301080
100 120 100 120 150 BGF/AGF1001201501080
BGF/AGF10012015010100
120 140 120 140 +0.088 +0.063 170 BGF/AGF
1201401701080BGF/AGF
12014017010100
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
25
BGF../AGF.. a disegno BGF../AGF.. by design
Esempi | Examples
26
CaratteristicheFeatures U.M.
Carico ammissibileMax Load (din./stat.) N/mm2 40/170
Velocità di strisc. ammissibileMax sliding speed m/s 2,0
Coeff. di attrito µµ friction coefficient - 0,08 ÷ 0,15
Campo di temperatureTemperature field °C -40 ÷ +150
Resistenza a trazione Rm Tensile strenght Rm N/mm2 520
Limite di snervamento Yield Strenght N/mm2 400
Durezza BrinellHardness HB 90 ~ 150
Coeff. di conduzione termicaHeat Conducting Coefficient 58 W(m●K)-1
Coeff. dilatazione termicaHeat Expansion Coefficient 18.5●10-6 K-1
PVmax N/mm2 x m/s 2,8
CARATTERISTICHE
Le boccole di questo tipo sono completamente di bronzo e particolarmente indicate per le applicazioni che necessitano di una rilubrificazione in quanto operanti in ambienti sporchi. La superficie di strisciamento presenta alveoli che contribuiscono a migliorare la lubrificazione.Le boccole rullate si distinguono soprattutto per la loro parete sottile ed è grazie a questa caratteristica che a parità di diametro dell’albero e di sollecitazioni, l’ingombro è inferiore a quello di una boccola tornita o di un cuscinetto.Ne risultano i seguenti vantaggi:• ingombro minimo• risparmio di peso rispetto alle boccole tornite o
ai cuscinetti• impiego minimo di materiale• capacità massima di carico• dato che le boccole si ottengono da nastri è molto
semplice averle provviste di alveoli• si possono ottenere ragnature• manutenzione facile• la versione con colletto assorbe sia le spinte
assiali che radiali
Serie PB..AR/ARG/FP
BOCCOLE RULLATE IN BRONZO DIN 1494 e ISO 3547 Bronzo allo stagno
APPLICAZIONI
Sono ideali per macchinari che operano in
MATERIALE
E’ un bronzo allo stagno (CuSn8) con eccellenti caratteristiche di scorrimento. Questo materiale è particolarmente adatto quando occorre assicurare alta resistenza all’usura, alla grippatura, alle alte temperature, alla corrosione e un alto limite di fatica. La superficie di strisciamento è ottenuta per lavorazione meccanica e munita di rientranze romboidali (PBC..AR) o con fori passanti (PBC..FP) che permettono una maggior capacità di accumulare lubrificante o a rientranze romboidali riempite di lubrificante solido (PBC..ARG).
LUBRIFICAZIONE
Le boccole rullate in bronzo vanno sempre lubrificate, in tal modo non vengono solo migliorate le caratteristiche di scorrimento ma anche ottenuti i seguenti vantaggi:• lunga durata• protezione contro la corrosione dell’albero• tenuta contro polvere e corpi estraneiGià durante la progettazione bisogna prevedere la possibilità di lubrificazione e nel caso di grasso, và anche previsto il ripristino periodico. Se le sollecitazioni non sono estreme, è sufficiente prevedere delle boccole con alveoli romboidali, non sono indispensabili delle ragnature e si può utilizzare del grasso come lubrificante.Nel caso in cui si utilizzi dell’olio come lubrificante, si impiegano boccole con superficie liscia, con ragnatura o con alveoli a calotta.
Alveolo a losanga
Foro passante
Lozange indentations
Through hole
27
BOCCOLE RULLATE IN BRONZO DIN 1494 e ISO 3547 Bronzo allo stagno PB..AR/ARG/FP series
RULLED BRONZE BUSHINGS DIN 1494 e ISO 3547 Tin bronze
PB..AR
TYPICAL APPLICATIONS
This type of bushings is widely applied in hoisting machines and other construction machines, automobiles, tractors, trucks, machines tools and some mineral engines. It can be fabricated into bushes, half bushings, flanged bushes, trust washers, spherical bushing and so on.
PB..FP
STRUCTURE
These are similar to the PB..AR range, except there are solid lubricants embedded into the diamond shaped lubrication indents on the bushing surface, which provide good lubrication conditions at the start up stage, even with a lack of oil. It can be used in construction machinery, gear boxes, automotive clutch parts etc.
PB..ARG
presenza di impurità, di urti e/o di vibrazioni come per esempio: macchine agricole, impianti di sollevamento, macchine edili, ecc.
MONTAGGIO
La boccola va montata in una sede con tolleranza H7 o inferiore e con uno smusso di 15° (45° per boccole flangiate) per facilitare il montaggio.Una volta in sede la zona di giunzione deve essere opposta alla direzione del carico: il diametro interno della boccola assumerà la tolleranza H9. Gli alberi devono avere una durezza possibilmente superiore a 50 HRC, una rugosità compresa tra 0,4 e 0,8 µm ed una tolleranza tra e7 ed f7.
STRUCTURE
The bushings are wrapped from a cold formed homogeneous bronze (CuSn8) with exceptional material properties. The standard sizes incorporate holes, which are dispersed in a special way over the whole bushing surface. These holes serve as lubricant reservoirs to rapidly build up a lubrication film at the start of movement and thereafter reduce the running friction. The material is suitable for construction and agricultural machinery etc. where high load and slow movement occur.
FEATURES
• Easy for fitting and lubricating• High load capacity• Inner diameter machinable parts are available
against order• High level thermal conductivity• Minimum overall dimensions• Chemical resistance• Extended service life and lubrication intervals
than normal PBC..AR type bushings• Free selection of lubricants• Collection of dust and rub off particles in the
holesInitial pre-lubrication at assembly required
STRUCTURE
The bushings are wrapped from a cold formed homogeneous bronze (CuSn8) with exceptional material properties. The standard sizes are fitted with diamond shaped lubrication indents in the bushing surface. These indents serve as lubricant reservoirs to rapidly build up a lubrication film at the start of movement and thereafter reduce the running friction. The material is suitable for construction and agricultural machinery applications.
FEATURES
• Easy for fitting and lubricating• High load capacity• Inner diameter machinable parts are
available against order• High level thermal conductivity• Minimum overall dimensions• Chemical resistanceInitial pre-lubrication at assembly required
TYPICAL APPLICATIONS
This type of bushings is widely applied in hoisting machines and other construction machines, automobiles, tractors, trucks, machines tools and some mineral engines. It can be fabricated into bushes, half bushings, flanged bushes, trust washers, spherical bushing and so on.
28
Metrico Metric standard
PBC..AR/FP cilindriche PBC..AR/FP cylindric
d DAlberoShaft
f7
SedeHousing
H7
SIGLADesignation
L 0 / -0,410 15 20 25 30 40 50 60 70 80 100
10 12 10 -0,013-0,028 12 +0,018
0PBC..AR/FP
101210 PBC..AR/FP
101215
12 14 12 -0,016-0,034 14 +0,018
0PBC..AR/FP
121410PBC..AR/FP
121415PBC..AR/FP
121420
14 16 14 -0,016-0,034 16 +0,018
0PBC..AR/FP
141610PBC..AR/FP
141615PBC..AR/FP
141620PBC..AR/FP
141625
15 17 15 -0,016-0,034 17 +0,018
0PBC..AR/FP
151710PBC..AR/FP
151715PBC..AR/FP
151720PBC..AR/FP
151725
16 18 16 -0,016-0,034 18 +0,018
0PBC..AR/FP
161810PBC..AR/FP
161815PBC..AR/FP
161820PBC..AR/FP
161825
18 20 18 -0,016-0,034 20 +0,021
0PBC..AR/FP
182010PBC..AR/FP
182015PBC..AR/FP
182020PBC..AR/FP
182025
20 23 20 -0,02-0,041 23 +0,021
0PBC..AR/FP
202310PBC..AR/FP
202315PBC..AR/FP
202320PBC..AR/FP
202325PBC..AR/FP
202330
22 25 22 -0,02-0,041 25 +0,021
0PBC..AR/FP
222515PBC..AR/FP
222520PBC..AR/FP
222525PBC..AR/FP
222530PBC..AR/FP
222540
24 27 24 -0,02-0,041 27 +0,021
0PBC..AR/FP
242730
25 28 25 -0,02-0,041 28 +0,021
0PBC..AR/FP
252815 PBC..AR/FP
252820 PBC..AR/FP
252825 PBC..AR/FP
252830
28 32 28 -0,02-0,041 32 +0,025
0PBC..AR/FP
283215PBC..AR/FP
283220PBC..AR/FP
283225PBC..AR/FP
283230
30 34 30 -0,02-0,041 34 +0,025
0PBC..AR/FP
303415PBC..AR/FP
303420PBC..AR/FP
303425PBC..AR/FP
303430PBC..AR/FP
303440
35 39 35 -0,025-0,05 39 +0,025
0PBC..AR/FP
353915PBC..AR/FP
353920PBC..AR/FP
353925PBC..AR/FP
353930PBC..AR/FP
353940PBC..AR/FP
353950
40 44 40 -0,025-0,05 44 +0,025
0PBC..AR/FP
404420PBC..AR/FP
404425PBC..AR/FP
404430PBC..AR/FP
404440PBC..AR/FP
404450PBC..AR/FP
404460
45 50 45 -0,025-0,05 50 +0,025
0PBC..AR/FP
455020PBC..AR/FP
455025PBC..AR/FP
455030PBC..AR/FP
455040PBC..AR/FP
455050PBC..AR/FP
455060
50 55 50 -0,025-0,05 55 +0,030
0PBC..AR/FP
505530 PBC..AR/FP
505540PBC..AR/FP
505550PBC..AR/FP
505560
55 60 55 -0,03-0,06 60 +0,030
0PBC..AR/FP
553600PBC..AR/FP
556040PBC..AR/FP
556050PBC..AR/FP
556060
60 65 60 -0,03-0,06 65 +0,030
0PBC..AR/FP
606530PBC..AR/FP
606540PBC..AR/FP
606550PBC..AR/FP
606560PBC..AR/FP
606570
65 70 65 -0,03-0,06 70 +0,030
0PBC..AR/FP
657050PBC..AR/FP
657070
70 75 70 -0,03-0,06 75 +0,030
0PBC..AR/FP
707540PBC..AR/FP
707550PBC..AR/FP
707560PBC..AR/FP
707580
75 80 75 -0,03-0,06 80 +0,030
0PBC..AR/FP
758050PBC..AR/FP
758060PBC..AR/FP
758080
80 85 80 0-0,03 85 +0,035
0PBC..AR/FP
808540PBC..AR/FP
808550PBC..AR/FP
808560PBC..AR/FP 8085100
85 90 85 0-0,035 90 +0,035
0PBC..AR/FP
859040PBC..AR/FP
859060PBC..AR/FP 8590100
90 95 90 0-0,035 95 +0,035
0PBC..AR/FP
909560PBC..AR/FP 9095100
100 105 100 0-0,035 105 +0,035
0PBC..AR/FP 10010560
PBC..AR/FP 100105100
105 110 105 0-0,035 110 +0,035
0PBC..AR/FP 10511060
PBC..AR/FP 105110100
110 115 110 0-0,035 115 +0,035
0PBC..AR/FP 11011560
PBC..AR/FP 110115100
115 120 115 0-0,035 120 +0,035
0PBC..AR/FP 11512060
PBC..AR/FP 115120100
120 125 120 0-0,035 125 +0,040
0PBC..AR/FP 12012560
PBC..AR/FP 120125100
125 130 125 0-0,04 130 +0,040
0PBC..AR/FP 12513060
PBC..AR/FP 125130100
130 135 130 0-0,04 135 +0,040
0PBC..AR/FP 13013560
PBC..AR/FP 130135100
140 145 140 0-0,04 145 +0,040
0PBC..AR/FP 14014560
PBC..AR/FP 140145100
150 155 150 0-0,04 155 +0,040
0PBC..AR/FP 15015560
PBC..AR/FP 150155100
160 165 160 0-0,04 165 +0,040
0PBC..AR/FP 16016560
PBC..AR/FP 160165100
Unit: mm
L
d DSplit f 2
f 1
min.o,3
45°± 5°
20°± 5°
DetailA DetailA
continua ...
29
PBF.. AR/FP flangiate PBF.. AR/FP flanged
Metrico Metric standard
d DAlberoShaft
f7
SedeHousing
H7
SIGLADesignation
L 0 / -0,410 15 20 25 30 40 50 60 70 80 100
170 175 170 0-0,040 175 +0,040
+0PBC..AR/FP17017540
PBC..AR/FP17017570
PBC..AR/FP170175100
180 185 180 0-0,040 185 +0,046
+0PBC..AR/FP18018540
PBC..AR/FP18018570
PBC..AR/FP180185100
190 195 190 0-0,046 195 +0,046
+0PBC..AR/FP19019540
PBC..AR/FP19019570
PBC..AR/FP190195100
200 205 200 0-0,046 205 +0,046
+0PBC..AR/FP20020540
PBC..AR/FP20020570
PBC..AR/FP200205100
220 225 220 0-0,046 225 +0,046
+0PBC..AR/FP22022540
PBC..AR/FP220225100
PBC..AR/FP220225100
250 255 250 0-0,046 255 +0,052
+0PBC..AR/FP25025540
PBC..AR/FP25025570
PBC..AR/FP250255100
260 265 260 0-0,052 265 +0,052
+0PBC..AR/FP26026540
PBC..AR/FP26026570
PBC..AR/FP260265100
280 285 280 0-0,052 285 +0,052
+0PBC..AR/FP28028540
PBC..AR/FP28028570
PBC..AR/FP280285100
300 305 300 0-0,052 305 +0,052
+0PBC..AR/FP30030540
PBC..AR/FP30030570
PBC..AR/FP300305100
Unit: mm
Split
L
d 3 d 1 d 2
R0,5 ~ 21
45°± 5°f 2
f 1
min.o,3
20°± 5°DetailA DetailA
d d2 d3AlberoShaft
f7
SedeHousing
H7
SIGLADesignation
L 0 / -0,415 20 25 30 35 40 45 50 60 70 80 90
25 28 35 25 -0,020-0,041 28 +0,021
+0PBF..AR 25150
PBF..AR 25250
30 34 45 30 -0,020-0,041 34 +0,025
+0PBF..AR 30150
PBF..AR 30300
35 39 50 35 -0,025-0,050 39 +0,025
+0PBF..AR 35200
PBF..AR 35350
40 44 55 40 -0,025-0,050 44 +0,025
+0PBF..AR 40250
PBF..AR 40400
45 50 60 45 -0,025-0,050 50 +0,025
+0PBF..AR 45300
PBF..AR 45450
PBF..AR 45500
50 55 65 50 -0,025-0,050 55 +0,030
+0PBF..AR 50300
PBF..AR 50500
55 60 70 55 -0,030-0,060 60 +0,030
+0PBF..AR 55300
PBF..AR 55500
60 65 75 60 -0,030-0,060 65 +0,030
+0PBF..AR 60300
PBF..AR60350
PBF..AR60500
65 70 80 65 -0,030-0,060 70 +0,030
+0PBF..AR65300
PBF..AR65600
70 75 85 70 -0,030-0,060 75 +0,030
+0PBF..AR70400
PBF..AR70700
75 80 90 75 -0,030-0,060 80 +0,035
+0PBF..AR75400
PBF..AR70700
80 85 100 80 -0-0,030 85 +0,035
+0PBF..AR80400
PBF..AR80800
90 95 110 90 -0-0,035 95 +0,035
+0PBF..AR90500
PBF..AR90900
100 105 120 100 -0-0,035 105 +0,035
+0PBF..AR100500
PBF..AR100900
110 115 130 110 -0-0,035 115 +0,035
+0PBF..AR110500
PBF..AR110900
120 125 140 120 -0-0,035 125 +0,040
+0PBF..AR120500
PBF..AR120900
130 135 155 130 -0-0,040 135 +0,040
+0PBF..AR130600
PBF..AR130900
140 145 165 140 -0-0,040 145 +0,040
+0PBF..AR140600
PBF..AR140900
150 155 180 150 -0-0,040 155 +0,040
+0PBF..AR150600
PBF..AR150900
160 165 190 160 -0-0,040 165 +0,040
+0PBF..AR160600
PBF..AR160900
170 175 200 170 -0-0,040 175 +0,040
+0PBF..AR170600
PBF..AR160900
180 185 215 180 -0-0,040 185 +0,046
+0PBF..AR180600
PBF..AR180900
190 195 225 190 -0-0,046 195 +0,046
+0PBF..AR190600
PBF..AR190900
200 205 235 200 -0-0,046 205 +0,046
+0PBF..AR200600
PBF..AR200900
225 230 260 225 -0-0,046 230 +0,046
+0PBF..AR225600
PBF..AR225900
250 255 290 250 -0-0,046 255 +0,052
+0PBF..AR250600
PBF..AR250900
265 270 305 265 -0-0,052 270 +0,052
+0PBF..AR265600
PBF..AR265900
285 290 325 285 -0-0,052 290 +0,052
+0PBF..AR285600
PBF..AR285900
300 305 340 300 -0-0,052 305 +0,052
+0PBF..AR300600
PBF..AR300900
FORNIBILI ANCHE A DISEGNO CON QUALSIASI DIMENSIONE SU RICHIESTACAN BE PRODUCED AT DRAWING WITH ANY DIMENSION ON REQUEST
30
Serie BJ800..BOCCOLE BIMETALLICHE Lega acciaio/bronzo secondo ISO3547
CARATTERISTICHE
Le boccola BJ è costituita da una lega bimetallica di acciaio/bronzo al piombo, che ha la caratteristica di poter sopportare elevate velocità di scorrimento e grazie alla sua alta capacità di carico questo tipo di boccola viene usata specialmente nell’industria automobilistica, nella costruzione di motori, pompe, compressori, macchine agricole, ecc.Sono costruite secondo la norma ISO3547.
STRUTTURA
La boccola bimetallica BJ è composta da diversi strati:Polvere di bronzo sinterizzata: buona resistenza all’usura ed ottime capacità di carico.Armatura in acciaio : consente una elevata capacità di carico ed una eccellente dissipazione del caloreRamatura: 0,002 millimetri (su richiesta) garantiscono una buona resistenza alla corrosione
Tipo / type BJ-800 BJ-720 BJ-700 BJ-20
Carico statico MaxStatic load Limit N/mm2 150 130 120 100
Carico di rottura a trazioneTensile Strenght N/mm2 185 150 200 200
Velocità (olio)Speed limit (oil) m/s 5 10 15 25
Velocità (grasso)Speed limit (grease) m/s 2,5 2,5 2,5 -
Coefficiente di attrito (olio)Friction coefficient (oil) μ 0,06-0,14 0,06-0,16 0,08-0,16 0,08-0,17
Limite PVPV limit N/mm2 x m/s
Grasso / Grease 2,8 2,8 2,5 -
Olio / Oil 10 10 8 6
Spessore nominaleNominal thickness 1 1,5 2 2,5 3 3,5 4 5
Spessore dell’armatura in acciaioThickness of steel backing 0,6 1 1.4 1.9 2.3 2.8 3.2 4
Spessore del bronzoThickness of bronze layer 0,4 0,5 0,6 0,6 0,7 0,7 0,8 1,0
Tolleranze ammesse Manufacturable wall thickness 1
+0,251,5
+0,252
+0,252,5
+0,253
+0,253.5
+0,254
+0,255
+0,25
+0,15 +0,15 +0,15 +0,15 +0,15 +0,15 +0,15 +0,15
Tolleranze di produzione Manufacturing wall thickness 1
01,5
02
02,5
03
03.5
04
05
0
-0,025 -0,03 -0,035 -0,04 -0,045 -0,05 -0,055 -0,06
PROPRIETÀ FISICHEPHISICAL CHARACTERISTICS
TOLLERANZA SULLO SPESSORETHICKNESS OF BJ BUSHINGS
Serie BJ800
31
BJ800.. seriesBIMETALLIC BUSHINGS Steel shell/lead bronze according ISO3547
Serie BJ850 La serie BJ_850 è un tipo di boccola bimetallica costituita da uno strato interno in bronzo 6-6-3 (85% Cu, 6% Sn, 6% Zn, 3% Pb) e un armatura esterna in acciaio a basso tenore di carbonio ricavata da semilavorato. Tale boccola ha proprietà simili alle BJ_800. Tale boccola ha le stesse proprietà della boccola BJ_800. Può essere prodotta in forma cilindrica, flangiata e ralla.PRINCIPALI CARATTERISTICHE TECNICHEC0 max 120 N/mm2
C max 65 N/mm2
Durezza strato in bronzo 70-100 HBTemperatura massima 260 °C
STRUCTURE
Sinter bronze powder: good wear resistance and excellent load carrying capacity.Steel backing: provides exceptionally high load carrying capacity, excellent heat dissipation. Copper plating thickness 0.002 mm: provides good corrosion resistance.
FEATURES
The BJ bushing is produced with steel shell backed with a lead bronze lining bushing material for oil lubricated applications. This material has high load capacity and good fatigue properties. It is widely used in automotive applications such as compressors, steering gear, power steering, pedal bearings, king-pin bushes, tailgate pivots, mechanical handling and lifting equipment, hydraulic motors, agricultural machinery etc.
BJ850 Series BJ_850 is a steel-bronze bushing, with a internal layer of sintered bronze 663 and a C20 steel as backing. This structure performance are similar to 663 bronze bushing but can saving cost. So it can replace thick wall bronze bushing and improve product competence to use in oil box, construction machines and other high precision but low speed occasions.This bushing is available in cylindrical, flanged and washer version.TECHNICAL SPECIFICATIONS C0 max 120 N/mm2
C max 65 N/mm2
Hardness Alloy 70-100 HBTemperature max. 260 °C
SiglaMaterial type BJ-800 BJ-720 BJ-700 BJ-20
Lega bronzoSpecification of bronze CuPb10Sn10 CuPb24Sn4 CuPb30 AlSn20Cu
EquivalenzeEquivalent standard code
USA: SAE-797GERMANY: GLYCO 66
JAPAN: JIS-LBC3
USA: SAE-799GERMANY: GLYCO 68
JAPAN: JIS-LBC6
USA: SAE-48JAPAN: JIS-KJ3
USA: SAE-783GERMANY: GLYCO 74
JAPAN: JIS-AJL
MetallografiaMetallographies
DurezzaHardness HB 70~100 45~70 30~45 30~40
C max N/mm2 65 38 25 30
T. Max. °C 260 200 170 150Tipo più resistente, con vasto campo di applicazioni, più adatto a boccole e ralle con carichi vibranti. The strongest type, wide application field, most suitable for high impact vibrating load bushes and Washers.
Adatta a carichi medi con basso coefficiente di attrito.Relative high fatigue strength & load capacity, good sliding performance. poor oil corrosion resistance. Fit for middle load, middle speed
Adatta per bassi carichi con ottime caratteristiche di scorrimento. Good seizuring resistance good capacity to submerge foreign, overlayer plated normally applied in main bushings of high speed, low to moderate load
Ottime caratteristiche di scorrimento in presenza di alti carichi.Moderate fatique strength & load capacity good corrosion resistance, reIative good sliding performance.
COMPOSIZIONE CHIMICA E CARATTERISTICHE DI APPLICAZIONE DELLE BOCCOLE BJCHEMICAL COMPOSITIONS AND APPLICATION CHARACTERISTICS OF STEEL-LEAD BRONZE ALLOYS
32
Serie BJ800..BOCCOLE BIMETALLICHE Lega acciaio/bronzo secondo ISO3547
TIPI DI SCANALATURE DELLE BOCCOLE BJBJ BUSH’S GROOVES & INDENTATIONS
TIPO DI GIUNZIONE DELLE BOCCOLE BJLOCK TYPES OF BJ WRAPPED BUSHES
A = Giunzione diritta B = Giunzione a farfalla A = Straight joint B = Inter Locking Joint
ESEMPIO DI CODIFICA:CODING EXAMPLE:
BJ C 800 A 50 50 G
LE BOCCOLE DELLA SERIE BJ SONO FORNIBILI IN TUTTE LE MISURE DELLA SERIE PBTHE BJ BUSHES ARE AVAILABLE IN ALL SIZE OF PB SERIES
A B C D E F
G
C (cilindrica/cylindrical) F (flangiata /flanged)
Tipo di materiale Material Type (es. 800)
° Tipo di giunzione Lock Types
Diametro internoInside Diameter
LunghezzaLenght
Tipo di scanalaturaGrooves or indentations Type
Distributore / Distributor
ITS Italia Via Pio X, 7 35010 S. Giustina in Colle Padova Italy Tel. 049 9301111 Fax 049 9317906 VOIP 049 8592859 commerciale@itsitalia.org www.itsitalia.org
Cat
alog
o te
cnic
ocu
scin
etti
a st
risci
amen
to D
jam
ond
Rev
. 01
top related