installation over the range instructions microwave...

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Over the RangeInstructions Microwave Oven

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for local inspector’s use.

• IMPORTANT – Observe all governing codes and ordinances.

• Note to Installer – Be sure to leave theseinstructions with the Consumer.

BEFORE YOU BEGIN• Note to Consumer – Keep these

instructions for future reference.• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.• Proper installation is the responsibility of the installer. • Product failure due to improper installation is not

covered under the Warranty.

Need Help?For customers in the United States, call: 1-800-944-9044For Canadian customers, call: 1-866-294-9911

P/N 316137222

Recirculating ........................................ 19–22

Attach Mounting Plate to Wall ............19

Preparation of Top Cabinet ................19

Check Microwave Assembly ................20

Adapting Microwave Blower for Recirculation............................20–21

Mount the Microwave Oven..............................................21–22

Installing the Charcoal Filter ..............22

Before You Use Your Microwave .......................... 23

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Hood Exhaust ...................................................... 4–5

Damage – Shipment/Installation.............................. 6

Parts Included.......................................................... 6

Tools You Will Need ................................................ 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8–10

Removing the Mounting Plate ...................... 8

Finding the Wall Studs .................................. 8

Determining Wall Plate Location .................. 9

Aligning the Wall Plate................................ 10

Installation Types.............................................. 11–22

Outside Top Exhaust ............................ 12–14

Attach Mounting Plate to Wall ............12

Checking for Proper DamperOperation ............................................13

Mount the Microwave Oven ................13

Adjust the Exhaust Adaptor ................14

Connecting Ductwork..........................14

Outside Back Exhaust ............................ 15–18

Preparing Rear Wall for Outside Back Exhaust ..........................15

Removing Exhaust Adaptor ................15

Attach Mounting Plate to Wall ..............16

Adapting Microwave Blowerfor Outside Back Exhaust ................16–17

Mount the Microwave Oven ................18

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONSThis product requires a three-prong grounded outlet. The installer must perform a ground continuitycheck on the power outlet box before beginning theinstallation to insure that the outlet box is properlygrounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installationto avoid severe or fatal shock injury.

CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63-85 pound (28.6-38.6 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg) or a total weight of 113-135pounds (51.3-61.2 kg).

CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal safety, it is recommended that two people install this product.IMPORTANT—PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

You should have the wall receptacle and circuit checkedby a qualified electrician to make sure the receptacle isproperly grounded.

Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle,installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICALREQUIREMENTSProduct rating is 120 volts AC, 60 Hertz, 15 amps and1.58 kilowatts. This product must be connected to asupply circuit of the proper voltage and frequency.Wire size must conform to the requirements of theNational Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord andplug should be brought to a separate 15 to 20 amperebranch circuit single grounded outlet. The outlet boxshould be located in the cabinet above the microwaveoven. The outlet box and supply circuit should beinstalled by a qualified electrician and conform to theNational Electrical Code or the prevailing local code.

Insure properground existsbefore use

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Roof Cap 24 Ft. x (1) = 24 Ft.(7.32 m) (7.32 m)

12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft.(6″ Round) (3.66 m) (3.66 m)

Rectangular-to-Round 5 Ft. x (1) = 5 Ft.Transition Adaptor* (1.52 m) (1.52 m)

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

Total Length = 41 Ft. (12.50 m)

HOOD EXHAUST

The following chart describes an example of one possibleductwork installation.

NOTE: Read these next two pages only if you plan to vent your exhaust to theoutside. If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be preparedat the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

The following chart describes an example of one possibleductwork installation.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

DUCT PIECES LENGTH* x USED = LENGTH

Wall Cap 40 Ft. x (1) = 40 Ft.(12.19 m) (12.19 m)

3 Ft. Straight Duct 3 Ft. x (1) = 3 Ft.(31⁄4″ x 10″ Rectangular) (91.44 cm) (91.44 cm)

90° Elbow 10 Ft. x (2) = 20 Ft.(3.05 m) (6.10 m)

Total Length = 63 Ft. (19.20 m)

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5 Ft. x ( ) = Ft.Transition Adaptor* (1.52 m) (m)

Wall Cap 40 Ft. x ( ) = Ft.(12.19 m) (m)

90° Elbow 10 Ft. x ( ) = Ft.(3.05 m) (m)

45° Elbow 5 Ft. x ( ) = Ft.(1.52 m) (m)

90° Elbow 25 Ft. x ( ) = Ft.(7.62 m) (m)

45° Elbow 5 Ft. x ( ) = Ft.(1.52 m) (m)

Roof Cap 24 Ft. x ( ) = Ft.(7.32 m) (m)

Straight Duct 6″ Round or 1 Ft. x ( ) = Ft.31⁄4″ x 10″ Rectangular (30.48 cm) (cm)

Total Ductwork = Ft. (m)

* IMPORTANT: If a rectangular-to-round transitionadaptor is used, the bottom corners of the damperwill have to be cut to fit, using the tin snips, in orderto allow free movement of the damper.

NOTE: If you need to install ducts, note that the total ductlength of 31⁄4″ x 10″ rectangular or 6″ diameter round ductshould not exceed 140 equivalent feet (42.67 m). Outside ventilation requires a HOOD EXHAUST DUCT.Read the following carefully. NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps preventblockages. Also, make sure dampers swing freely andnothing is blocking the ducts.

Exhaust connection: The hood exhaust has been designed to mate with a standard 31⁄4″ x 10″ rectangular duct.If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6″ diameter duct.

Maximum duct length: For satisfactory air movement, the total duct length of 31⁄4″ x 10″ rectangular or 6″ diameter round duct shouldnot exceed 140 equivalent feet (42.67 m).

Elbows, transitions, wall and roof caps,etc., present additional resistance to airflow and areequivalent to a section of straight duct which is longerthan their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straightduct sections. The chart below shows you how to calculate total equivalent ductwork length using theapproximate feet of equivalent length of some typicalducts.

PART QUANTITY

Top Cabinet 1Template

Rear Wall 1Template

Installation 1Instructions

Separately 2Packed Grease Filters

PART QUANTITY

Wood Screws 2(1⁄4″ x 2″)

Toggle Bolts (and 4 wing nuts) (3⁄16″ x 3″)

Self-aligning Machine 3 Screws (1⁄4″-28 x 31⁄4″)

Nylon Grommet 2(for metal cabinets)

• If the unit is damaged in shipment, return theunit to the store in which it was bought for repairor replacement.

• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if otherthan the customer), repair or replacement mustbe made by arrangement between customer and installer.

DAMAGE – SHIPMENT/INSTALLATION

PARTS INCLUDED

You will find the installation hardware contained ina packet with the unit. Check to make sure you haveall these parts.NOTE: Some extra parts are included.

HARDWARE PACKET

ADDITIONAL PARTS

TOP CABINET TEMPLATE

REARWALL

TEMPLATE

TOOLS YOU WILL NEED

#1 and #2 Phillips screwdriver Pencil

Ruler or tape measure andstraight edge

Carpenter square(optional)

Tin snips (for cuttingdamper, if required)

Electric drill with 3⁄16″, 1⁄2″ and 5⁄8″drill bits

Hammer (optional)Stud finder or

Filler blocks or scrapwood pieces, if needed for top cabinet spacing(used on recessed bottomcabinet installations only)

Gloves

Saw (saber, hole or keyhole)

LevelDuct and masking tape

MOUNTING SPACE

NOTES:• The space between the cabinets must be 30″

(76.2 cm)wide and free of obstructions. • If the space between the cabinets is greater

than 30″ (76.2 cm), a Filler Panel Kit may beused to fill in the gap between the microwaveoven and the cabinets. Your Owner’s Manualcontains the kit number for your model.

• This microwave oven is for installation overranges up to 36″ (91.44 cm) wide.

• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section forexhaust duct preparation.

• When installing the microwave oven beneathsmooth, flat cabinets, be careful to follow theinstructions on the top cabinet template for power cord clearance.

Backsplash

66″ (167.64 cm)or more fromthe floor to thetop of themicrowave

30″ (76.2 cm)

2″ (5.08 cm)

30″ (76.2 cm) min.

161⁄2″ (41.91 cm)

Bottom edge ofcabinet needs tobe 30″ (76.2 cm)or more from thecooking surface

Scissors (to cut template, if necessary)

Safety goggles

Find the studs, using one of the following methods:A. Stud finder – a magnetic device which

locates nails.OR

B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.

After locating the stud(s), find the center by probing the wall with a small nail to find the edgesof the stud. Then place a mark halfway between theedges. The center of any adjacent studs should be16″ or 24″ (40.64 cm or 60.96 cm) from this mark.Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

Remove the installation instructions, filters, glasstray and the small hardware bag. Do not removethe Styrofoam protecting the front of the oven.

Fold back all 4 carton flaps fully against cartonsides. Then carefully roll the oven and carton overonto the top side. The oven should be resting inthe Styrofoam.

REMOVING THE MICROWAVEOVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE

FINDING THE WALL STUDSB.A.

PLACEMENT OF THE MOUNTING PLATE1

Wall Studs

Center

Carton

Pull the carton up and off the oven.

Remove the 2 screws from the mounting plate.This plate will be used as the rear wall templateand for mounting. You may discard these screws.

MountingPlateScrews

Styrofoam

Remove and properly discard plastic bags.4

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINETC.

Your cabinets may have decorative trim that interfereswith the microwave installation. Remove the decorativetrim to install the microwave properly and to make itlevel.

THE MICROWAVE MUST BE LEVEL.Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.

Measure the inside depth of the front overhang.

Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the insidedepth of the front overhang.For this type of installation with front overhang only,align the mounting tabs with this horizontal line, nottouching the cabinet bottom as described in Step D.

Plate position – beneath flat bottom cabinet

Plate position – beneath recessed bottomcabinet with front overhang

Mounting Plate Tabs Touching the Cabinet Bottom

Mounting Plate withTabs Below CabinetBottom the SameDistance as the FrontOverhang Depth

At least 30″ (76.2 cm), up to36″ (91.44 cm)

Plate position – beneath framed recessed cabinet bottom

30″ (76.2 cm) to Cooktop

Mounting Plate TabsTouching the BackFrame

30″ (76.2 cm) to Cooktop

ALIGNING THE WALL PLATE

Draw a vertical line on the wall at the center of the 30″(76.2 cm) wide space.Use the mounting plate as the template for the rearwall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinetswith front overhang. Line up the notch and center lineon the bottom of the mounting plate to the center lineon the wall.While holding the mounting plate with one hand, draw circles on the wall at holes A, B, C and D (see illustration above/actual plate marked with arrows).Four holes must be used for mounting.

NOTE: Holes C and D are inside area E. If neither C nor D is in a stud, find a stud somewhere in area Eand draw a fifth circle to line up with the stud. It isimportant to use at least one wood screw mounted firmly in a stud to support the weight of the microwave.Set the mounting plate aside.Drill holes on the circles. If there is a stud, drill a 3⁄16″hole for wood screws. For holes that don’t line up witha stud, drill a 5⁄8″ hole for toggle bolts.NOTE: DO NOT MOUNT THE PLATE AT THISTIME.

Draw a VerticalLine on Wallfrom Center ofTop Cabinet

Area E

Hole A

Hole B

Hole D

CAUTION: Wear glovesto avoid cutting fingers onsharp edges.

Hole CCenterlinenotches

INSTALLATION TYPES (Choose A, B or C)

This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct)B. Outside Back Exhaust (Horizontal Duct)C.Recirculating (Non-Vented Ductless)

NOTE: This microwave is shipped assembled for OutsideTop Exhaust (except for non-vented models). Select thetype of ventilation required for your installation and proceed to that section.

OUTSIDE TOP EXHAUST(VERTICAL DUCT)

OUTSIDE BACK EXHAUST(HORIZONTAL DUCT)

RECIRCULATING(NON-VENTED DUCTLESS)

See page 12 See page 15

See page 19

A Charcoal Filter AccessoryKit is required for the non-vented exhaust. (See your Owner’s Manual for the kit number.)

Adaptor in Place forOutside Top Exhaust

OUTSIDE TOP EXHAUST (Vertical Duct)

Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flush against the wall and that the plate is properlycentered under the cabinet.CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wallto help tighten the bolts.

ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through theholes designated to go into drywall and reattach thetoggle wings to 3⁄4″ (19.05 mm) onto each bolt.

INSTALLATION OVERVIEWA1. Attach Mounting Plate to WallA2. Prepare Top CabinetA3. Check Damper OperationA4. Mount Microwave OvenA5. Adjust Exhaust AdaptorA6. Connect Ductwork

MountingPlate

Spacing for TogglesMore Than WallThickness

Bolt End

Toggle Bolt

Toggle Wings

To use toggle bolts:

MOUNT THE MICROWAVEOVEN

CHECK FOR PROPERDAMPER OPERATION

USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes for the top support screws, ahole large enough for the power cord to fit through,and a cutout large enough for the exhaust adaptor.

FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handleduring installation.NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after thethreads have engaged. (It will be completelytightened later.) Be sure to keep power cordtight. Be careful not to pinch the cord, especiallywhen mounting flush to bottom of cabinet.

NOTE: When mountingthe microwave oven,thread power cordthrough hole in bottom oftop cabinet. Keep it tightthroughout Steps 1–3. Donot pinch cord or liftoven by pulling cord.

Lift microwave, tilt itforward, and hookslots at back bottomedge onto four lowertabs of mountingplate.

Exhaust Adaptor(absent on models shippedfor recirculation exhaust)Blower Plate

Damper

Back ofMicrowave

• Read the instructions on the TOP CABINET TEMPLATE.

• Tape it underneath the top cabinet.• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holesin the cabinet bottom.

• Place the microwave in its upright position, with thetop of the unit facing up.

• This microwave oven may be shipped assembled fortop exhaust (adaptor installed) or for recirculationexhaust (adaptor absent).

• Make sure tape securing damper is removed anddamper pivots easily before mounting microwave.

• You will need to make adjustments to assure properalignment with your house exhaust duct after themicrowave is installed.

2 Rotate front of ovenup against cabinet bottom.

4 Attach the microwave oven to the top cabinet.

Cabinet Front

Cabinet Bottom Shelf

Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.)

Filler Block

Microwave Oven Top

Equivalent toDepth of CabinetRecess

Insert 2 self-aligning screwsthrough outer top cabinetholes. Turn two full turns oneach screw.

Tighten center screw completely.

Install grease filters. See the Owner’s Manualpacked with the microwave.

ADJUST THE EXHAUSTADAPTOR

Open the top cabinet and adjust the exhaust adaptorto connect to the house duct.

Back of Microwave

For Front-to-Back or Side-to-SideAdjustment, Slide theExhaust Adaptor asNeeded

Blower Plate Damper

CONNECTING DUCTWORK

Extend the house duct down to connect tothe exhaust adaptor. Seal exhaust duct joints using duct tape.

House Duct

Self-Aligning Screw

This microwave oven is shipped assembled for topexhaust. You will need the exhaust adaptor forinstallation in the rear wall opening. To remove theexhaust adaptor from the microwave oven:

Remove tape securing damper.

OUTSIDE BACK EXHAUST (Horizontal Duct)

Lift off theblower plateand attachedadaptor fromthe microwave.

INSTALLATION OVERVIEWB1. Prepare Rear WallB2. Remove Exhaust AdaptorB3. Attach Mounting Plate to WallB4. Prepare Top CabinetB5. Adjust BlowerB6. Mount the Microwave Oven

Slide exhaust adaptor to one side and remove it.

Back ofMicrowave

Remove andsave screwthat holdsblower plateto microwave.

Damper

PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall foroutside exhaust.

• Read the instructions on the REAR WALLTEMPLATE.

• Tape it to the rear wall, lining up with the holespreviously drilled for holes A and B in the wallplate.

• Cut the opening, following the instructions of theREAR WALL TEMPLATE.

REMOVE EXHAUST ADAPTOR B2.

ATTACH THE MOUNTINGPLATE TO THE WALL

B3. USE TOP CABINET TEMPLATEFOR PREPARATION OF TOP CABINET

• Read the instructions on the TOP CABINETTEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

MountingPlate

Spacing for Toggles MoreThan Wall Thickness

Toggle Bolt

Toggle Wings

Bolt End

You need to drill holes for the top support screws anda hole large enough for the power cord to fit through.

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

Insert the bolts into the mounting plate throughthe holes designated to go into drywall and reattachthe toggle wings to 3⁄4″ (19.05 mm) onto each bolt.

NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet.CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.

BEFORE: Fan BladeOpenings Facing Up

1 Remove and save screw that holds blower motorto microwave.

ADAPTING MICROWAVEBLOWER FOR OUTSIDEBACK EXHAUST

Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust theblower unit.

Back ofMicrowave

Blower Motor

Blower MotorScrew

Attach the exhaust adaptor to the rear of theoven by sliding it into the guides at the topcenter of the back of the oven.

AFTER: Fan BladeOpenings Facing Back

6 Place the blower unit back into the opening.

8 Replace the blower plate in the same positionas before with the screw.

Roll the blower unit 90° so that fan bladeopenings are facing out the back of themicrowave.

ADAPTING MICROWAVEBLOWER FOR OUTSIDEBACK EXHAUST (cont.)

Rotate blower unit counterclockwise 180°.

Before Rotation After Rotation

Gently remove the wires from the grooves.Reroute the wires through grooves on other sideof the blower unit.

Before Rerouting After Rerouting

Wires Routed Through Right Side Wires Routed Through Left Side

Back ofMicrowave

Blower Plate

Blower MotorScrew

Secure the blower unit to the microwave withthe screw from Step 1.

Before Rolling After Rolling

Back ofMicrowave

CAUTION: Do not pull or stretch the blowerunit wiring. Make sure the wires are notpinched.NOTE: The blower unit exhaustopenings should match exhaustopenings on rear of microwave oven.

Push in securely until it is in the lower lockingtabs. Take care to assure that the damper hingeis installed so that it is at the top and that thedamper swings freely.

Adaptor

Locking Tabs

Back of Microwave

Attach the microwave oven to the top cabinet.

FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handleduring installation.NOTE: If your cabinet is metal, use the nylongrommet around the power cord hole to preventcutting of the cord.NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after thethreads have engaged. (It will be completelytightened later.) Be sure to keep power cord tight.Be careful not to pinch the cord, especially whenmounting flush to bottom of cabinet.

Cabinet Front

Filler Block

Microwave Oven Top

Equivalent to Depth of CabinetRecess

Self-Aligning Screw

USE TOP CABINET TEMPLATEFOR PREPARATION OF TOP CABINET

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEWC1. Attach Mounting Plate to WallC2. Prepare Top Cabinet C3. Check Microwave AssemblyC4. Adjust BlowerC5. Mount the Microwave OvenC6. Install Charcoal Filter

• Read the instructions on the TOP CABINETTEMPLATE.

CAUTION: Wear safety goggles when drilling holesin the cabinet bottom.

You need to drill holes for the top support screws anda hole large enough for the power cord to fit through.

NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet.CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.

3ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At leastone wood screw must be used to attach the plate to awall stud.

Insert the bolts into the mounting plate through the holes designated to go into drywall and reattachthe toggle wings to 3⁄4″ (19.05 mm) onto each bolt.

MountingPlate

Spacing for TogglesMore Than WallThickness

Bolt End

Toggle Bolt

Toggle Wings

AFTER: Fan BladeOpenings Facing Forward

ADAPTING MICROWAVEBLOWER FOR RECIRCULATION

NOTE: The exhaust adaptor with damper is notneeded for recirculating models. You may want tosave them for possible future use.

Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust theblower unit.

Roll the blower unit 90° so that fan blade openingsare facing toward the front of the microwave.

Slide exhaust adaptor to one side and remove it.

Remove and save the screw that holds the blowermotor to the microwave.

Blower Plate

Blower MotorScrew

Back ofMicrowave

Remove and savescrew thatholds blower plate tomicrowave.

Lift off theblower plateand attachedadaptor fromthe microwave.

NOTE: Make sure wires remain routed in thegrooves of the motor frame.

BEFORE: Fan BladeOpenings Facing Up

Damper

Back ofMicrowave

CHECK MICROWAVE ASSEMBLYC3.

Exhaust Adaptor (absent on models shipped forrecirculation exhaust)

Back ofMicrowave

• Place the microwave in its upright position, with thetop of the unit facing up.

• The microwave oven may be shipped assembled fortop exhaust (adaptor installed) or for recirculationexhaust (adaptor absent).

• If the microwave was shipped for recirculationexhaust, skip to C5. If shipped for top exhaust,proceed with C4.

ADAPTING MICROWAVEBLOWER FOR RECIRCULATION (continued)

Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unitwiring. Make sure the wires are not pinched.

Replace blower plate with the screw removed inStep 1.

Secure blower unit to microwave with the screwremoved in Step 4.

Attach the microwave oven to the top cabinet.

Cabinet Front

Filler Block

Microwave Oven Top

Equivalent to Depthof Cabinet Recess

Back ofMicrowave

FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handleduring installation.NOTE: If your cabinet is metal, use the nylongrommet around the power cord hole to preventcutting of the cord.NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,case damage may occur from over tighteningscrews.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after thethreads have engaged. (It will be completelytightened later.) Be sure to keep power cordtight. Be careful not to pinch the cord, especiallywhen mounting flush to bottom of cabinet.

Self-Aligning Screw

INSTALLING THE CHARCOAL FILTER

C6.MOUNT THE MICROWAVEOVEN (continued)

Install the charcoal filter. When properly installed,the wire mesh of the filter should be visible fromthe front.Replace the grille and the 2 screws.

Close the door.

CharcoalFilter

145 Series Model 168 Series Model

Insert mesh-side up

Remove 2 screws on front of grille using a #1Phillips screwdriver.Open the door.Remove the grille.

Insert mesh-side down

KEEP INSTALLATION INSTRUCTIONSFOR THE LOCAL INSPECTOR’S USE.

Plug power cord into a dedicated 15 to 20 amp electrical outlet.

Read the Owner’s Manual.6.

Replace house fuse or turn breaker back on. 4.

Remove all packing material from the microwave oven.2.

Make sure the microwave oven has beeninstalled according to instructions.1.

BEFORE YOU USE YOUR MICROWAVE

Insure properground existsbefore use

Install turntable and ring in cavity.3.

164D3370P20549-40243

11-01 JR Printed in Korea

installation over the range instructions microwave...

Documents

mdg (all) installation instructions · 2020-05-06 · mdg...

installation instructions, jaws & jawsii · typical...

monteringsanvisning · installation instructions...

rear bracket attachment step 5) step 1) step 9 ......

ice maker installation instructions instructions d...

installation instructions instructions d’installation

alpha light installation instructions · alpha light...

powerflex 750-series option modules installation...

washer installation instructions instructions d

installation tips installation instructions

operating instructions installation & servicing instructions

qasair installation instructions 2015 - winning...

proarmor installation instructions - owens corning ·...

fios installation instructions - verizon · fios...

operating instructions & installation instructions

mda - multiple device adapter installation · pdf filemda -...

installation instructions – ssled tcb kit – field...

es200 control, self-cleaning...

installation instructions...

montageanleitung installation instructions instructions de