installation instructions for part 99-6510 · pdf filejeep commander 2006-2007 4 screws 4...
Post on 12-Mar-2018
214 Views
Preview:
TRANSCRIPT
INSTALLATION INSTRUCTIONS FOR PART 99-6510
Phillips Screwdriver • Socket Wrench •
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
• DIN Radio Provision with Pocket• ISO DIN Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Units Provision
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Pocket • F) Double DIN Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
BA
DE
CF
APPLICATIONS
Small Flat Blade Screwdriver orPanel Removal Tool
• Cutting Tool
Chrysler300 2005-2007 Aspen 2007
Commander 2006-2007Grand Cherokee 2005-2007
Jeep
Designed For Vehicles With Factory Navigation RadiosUsing this kit in vehicles without factory navigation requires the purchase of a factory navigation radio trim panel from your local Chrysler, Dodge or Jeep parts department
Ram 2006-2007
DodgeCharger 2005-2007 Durango 2005-2007 Magnum 2005-2007
99-6510
Dash Disassembly- Chrysler Aspen 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- Dodge Durango 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . 1- Dodge Charger 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . 2- Dodge Magnum 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . 2- Chrysler 300 2005-2007. . . . . . . . . . . . . . . . . . . . . . . . . . . 3- Dodge Ram 2007 (Without Center Console) . . . . . . . . . . . . 4- Dodge Ram 2007 (With Mini Center Console) . . . . . . . . . . . 5- Dodge Ram 2007 (With Full Center Console) . . . . . . . . . . . 6- Jeep Grand Cherokee 2005-2007 . . . . . . . . . . . . . . . . . . . . 7- Jeep Commander 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Kit Assembly- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 9- ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . 10- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . 11- Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . .12
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
TABLE OF CONTENTS
99-6510
1
99-6510 DASH DISASSEMBLY
DODGE DURANGO 2005-2007
CHRYSLER ASPEN 2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Remove (2) 7MM screws from the insideof the pocket facing upward. (Figure A)
1
2
Unclip and remove the entire trim panelsurrounding the radio and climate controls.(Figure B)
3
Remove (4) 7MM screws securing radioto dash and remove radio. (Figure C)
4
A
B
CContinue to kit assembly.5
2
99-6510 DASH DISASSEMBLY
DODGE MAGNUM 2005-2007 DODGE CHARGER 2005-2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Unclip and remove entire panel surroundingradio and climate controls, including a/cvents. (Figure A)
1
2
Remove (4) 7MM screws securing radioto dash and remove radio. (Figure B)
3
A
B
Continue to kit assembly.4
99-6510 DASH DISASSEMBLY
3
CHRYSLER 300 2005-2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Unclip and remove entire panel surround-ing radio and climate controls, includinga/c vents and clock. (Figure A)
1
2
Remove (4) 7MM screws securing radioto dash and remove radio. (Figure B)
3 B
A
Continue to kit assembly.4
99-6510 DASH DISASSEMBLY
4
DODGE RAM 2006-2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Open cup holder and remove (2) Phillipsscrews facing up on front edge ofradio/climate control panel. (Figure A)
1
2
Unclip and remove entire panel sur-rounding radio and climate controls,including a/c vents. (Figure B)
3
Remove (4) 7MM screws securing radioto dash and remove radio.
4
A
B
WITHOUT CENTER CONSOLE
Continue to kit assembly.5
99-6510 DASH DISASSEMBLY
5
DODGE RAM 2006-2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Remove center console inserts, if present.(Figure A)
1
3
Unclip and remove entire panel sur-rounding radio and climate controls,including a/c vents. (Figure E)
8
Remove (4) 7MM screws securing radioto dash and remove radio.
9
A
B
If vehicle has floor shifter, remove shifterknob.
2
C
WITH MINI CENTER CONSOLE
D E
Remove screws securing the rear centerconsole to the floor panel. Lift up on therear center console to clear the gear shiftlever, if present. (Figure B)
4
Remove screws securing the front centerconsole to the floor panel. Unclip andremove the front center console.(Figure C)
5
Loosen two 8 mm screws at bottom ofdash. Unsnap lower panel.
6
Remove (2) Phillips screws facing up onfront edge of radio/climate control panel.(Figure D)
7
Continue to kit assembly.5
99-6510 DASH DISASSEMBLY
6
Disconnect the negative battery terminalto prevent an accidental short circuit.
Unsnap and remove console front topcover (closest to the dash). (Figure A)
1
3
Unclip and remove entire panel surroundingradio and climate controls, including a/cvents. (Figure E)
7
Remove (4) 7MM screws securing radioto dash and remove radio.
8
A
B
If vehicle has floor shifter, remove shifterknob.
2
D
E
Remove two 8 mm screws from underconsole cover (previously removed).Remove front section of console.(Figure B)
4
5 Loosen two 8 mm screws at bottom ofdash. Unsnap lower panel.
Remove (2) Phillips screws facing up onfront edge of radio/climate control panel.(Figure D)
6
Continue to kit assembly.9
DODGE RAM 2006-2007
WITH FULL CENTER CONSOLE
7
99-6510 DASH DISASSEMBLY
JEEP GRAND CHEROKEE 2005-2007
Disconnect the negative battery terminalto prevent an accidental short circuit.
Unsnap and remove panel from aroundradio including the vent on each side.(Figure A)
1
2
Remove (4) 7MM screws securing radioto dash and remove radio. (Figure B)
3
A
B
Continue to kit assembly.4
8
99-6510 DASH DISASSEMBLY
JEEP COMMANDER 2006-2007
4 screws 4 screws 4 screws 4 screws
A
B
Disconnect the negative battery terminalto prevent an accidental short circuit.
Remove the (16) screws securing theradio trim panel. (Figure A)
1
2
Unclip and remove the entire radio trimpanel. (Figure B)
3
Remove (4) 7MM screws securing radio to dash and remove radio.4
Continue to kit assembly.5
9
99-6510 KIT ASSEMBLY
Slide the DIN cage into the radiohousing and secure by bending themetal locking tabs down. (Figure A)
1
Slide the aftermarket radio into thecage until secure. (Figure B)
2
Snap the pocket into the radiohousing. (Figure C)
3
DIN RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly. 4
10
99-6510 KIT ASSEMBLY
Mount the ISO Brackets to the radiowith the screws supplied with theunit. (Figure A)
1
Slide the radio into the radio openinguntil the side clips engage. (Figure B)
2
Snap the ISO Trim Plate into theradio housing. (Figure C)
3
Snap the pocket into the radio housing.(Figure C)
4
ISO RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly. 5
11
99-6510 KIT ASSEMBLY
Snap the DDIN brackets to the insideedge of the radio housing. (Figure B)
2
Snap the DDIN trim-plate onto thehousing/radio assembly. (Figure D)
4
Cut and remove center divider inradio housing. (Figure A)
1
Slide the DDIN radio unit into theDDIN bracket/radio housing assem-bly and secure the radio unit to thekit using the screws supplied withthe radio unit. (Figure C)
3
DOUBLE DIN RADIO PROVISION
A
B
C
Continue to final assembly. 5
D
12
99-6510 KIT ASSEMBLY
Cut and remove center divider inradio housing. (Figure A)
1
Snap the DDIN brackets to the insideedge of the radio housing. (Figure B)
2
Slide the stacked ISO DIN radio unitsinto the DDIN bracket/radio housingassembly and secure the unit to thekit using the screws supplied withthe units. (Figure C)
3
STACKED ISO UNITS PROVISION
A
B
C D
Snap the DDIN trim-plate onto thehousing/radio assembly. (Figure D)
4
Continue to final assembly. 5
13
99-6510 FINAL ASSEMBLY
FINAL ASSEMBLY
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-6510 INSTRUCTIONS
1-800-221-0932 www.metraonline.comREV. 06/14/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-6510
top related