imperial college london · web viewone of the important features of doped ceria is its mixed...
Post on 21-Jan-2021
5 Views
Preview:
TRANSCRIPT
Numerical modeling of nickel-infiltrated gadolinium-doped ceria electrodes reconstructed with
focused ion beam tomography
1,2Masashi Kishimoto*, 1Marina Lomberg, 1Enrique Ruiz-Trejo, 1Nigel P Brandon
1. Department of Earth Science and Engineering, Imperial College London, London SW7 2AZ,
United Kingdom
2. Department of Aeronautics and Astronautics, Kyoto University, Kyoto 615-8026, Japan
E-mail: kishimoto.masashi.3m@kyoto-u.ac.jp
Tel.: +81-(0)753833652
Abstract
A one-dimensional numerical model of a nickel-infiltrated gadolinium-doped ceria (Ni-GDC)
electrode has been developed to investigate the effects of electrode microstructure on performance.
Electrode microstructural information was obtained with focused ion beam tomography and
microstructural parameters were quantified, such as tortuosity factor, surface area and particle/pore
sizes. These have been used to estimate the effective transport coefficients and the electrochemical
reaction rate in the electrodes. GDC was considered as a mixed ionic and electronic conductor and
hence the electrochemical reaction is assumed to occur on the GDC-pore contact surface, i.e. double-
phase boundaries (DPBs). Sensitivity analysis was conducted to investigate the effect of electrode
microstructure on both transport properties and electrochemical activity, including the effect of DPB
density, GDC tortuosity factor and pore size. The developed model offers a basis to understand the
microstructure-performance relationships and to further optimize the electrode microstructures.
Key words: solid oxide fuel cells; infiltration; microstructure; FIB-SEM; modeling
1. Introduction
Doped ceria has been receiving significant attention as an alternative material for solid oxide
fuel cells (SOFCs) due to its higher oxide ion conductivity than conventional zirconia-based
materials at lower temperatures, making it possible to reduce the operating temperature of SOFCs.
Lowering the operating temperature enables reduction of the total cost of SOFC systems by allowing
use of inexpensive materials and mitigating thermally induced degradation. One of the important
features of doped ceria is its mixed conductivity under the reducing atmospheres [1–4], allowing
both electrons and oxide ions to migrate through the material. This broadens the electrochemical
reaction site from the triple-phase boundary (TPB) to the ceria-pore double-phase boundary (DPB)
[5–8].
It is widely accepted that electrode microstructure plays an important role in determining the
performance and durability of SOFCs. Electrodes are required to contain as many reaction sites as
possible to promote the electrochemical reaction; at the same time, effective mass and charge
transport pathways need to be established to and from the reaction sites. Therefore, the
microstructure-performance relationships need to be understood to develop high performance
electrodes. Three-dimensional (3D) imaging techniques, such as focused ion beam scanning electron
microscopy (FIB-SEM) [9–15] and X-ray nano CT [16–21], are finding increasing application in the
study of complex electrode microstructures. Through the development and application of
quantification methodologies and numerical simulation models, new insights have been generated,
which offer the prospect of optimizing electrode microstructure to further improve performance and
durability. We recently succeeded in imaging the microstructure of nickel-infiltrated gadolinium-
doped ceria (GDC) electrodes using FIB-SEM [12], where the infiltrated nickel particles (~100 nm)
were precisely imaged. It was revealed that the infiltrated electrodes had one order of magnitude
larger TPB density compared with conventional electrodes made by powder mixing and sintering
process.
To further extend this approach, reliable electrode simulation models are required to
investigate the effect of microstructure on the performance. Kishimoto et al. developed 1D and 3D
numerical models based on the finite volume method (FVM) coupled with the sub-grid-scale (SGS)
model to analyze the overpotential characteristics and the distribution of chemical species within Ni-
YSZ electrodes [11, 22–25]. Shikazono et al. developed 3D models based on the Lattice Boltzmann
Method (LBM) and analyzed Ni-YSZ anodes and LSCF cathodes [26–28]. Carraro, Joos and
Häffelin et al. developed a 3D model based on the finite element method (FEM) for a MIEC cathode
and conducted sensitivity analysis to elucidate the effect of various operating conditions on the
electrode performance [29–32]. Shearing and Cai et al. developed a 3D model based on the volume
of fluid (VOF) method and discussed the effect of image voxel size and reconstructed volume size on
the simulation results [33–35]. Although electrode structures in their model were synthesized by the
Monte Carlo method, their findings are particularly important to determine the required volume size
for the reconstructed structure to be representative of the whole electrode microstructures. Results
from these numerical analyses offer valuable insights to understand the effects of electrode
microstructure on electrode performance, which are otherwise very difficult to observe in
experiments.
For ceria-based materials, Chueh et al. conducted a two-dimensional numerical simulation on
a samarium-doped ceria (SDC) electrode to analyze the reaction region in the material, and found
that the rate-determining process was electron conduction from the SDC surface to the current
collector [36, 37]. They also found that the TPB length is not as influential on electrode performance
as in the case of conventional zirconia-based electrodes because the entire SDC-pore contact surface
can potentially act as a reaction zone. However, the simulation domain employed in their work was
limited to the Ni-SDC-pore contact region; hence it was difficult to assess the effect of
microstructure, such as phase volume fraction, DPB density and particle/pore sizes, on performance.
In this study, the 3D microstructure of infiltrated Ni-GDC electrodes is obtained using FIB-
SEM, and microstructural parameters that characterize the porous structures are quantitatively
evaluated, such as DPB density, particle/pore sizes and surface area. A 1D numerical model is then
developed to analyze the distribution of the charge carriers and gas species within the electrodes as
well as the electrochemical reaction. Sensitivity analysis using the developed model is conducted to
investigate the effect of several microstructural parameters on electrode performance, and insights
for microstructural optimization are generated.
2. Experimental
In this study, the electrochemical performance of an infiltrated Ni-GDC electrode was
characterized using an electrolyte-supported button cell, whose performance was used to validate the
proposed simulation model. First, a GDC scaffold (Ce0.9Gd0.1O1.95) was fabricated on an 8YSZ
electrolyte disk (Fuel Cell Materials) by screen printing an ink and sintering at 1350 °C for 2 h.
Second, the cathode was screen printed on the other side of the electrolyte using an LSCF-GDC ink
((La0.60Sr0.40)0.995(Co0.20Fe0.80)O3-x:Ce0.9Gd0.1O1.95 = 50:50 wt.%, Fuel Cell Materials) and sintering at
1100 °C for 2 h. Finally, nickel oxide nanoparticles were infiltrated into the scaffold by introducing
Ni(NO3)2 solution from the top of the scaffold followed by decomposition in air at 500 °C for
30 min. This infiltration process was repeated ten times, followed by a reduction process under a
hydrogen-nitrogen gas mixture (760 °C, H2:N2 = 50:50, 1 h). More details can be found elsewhere
[38].
Electrochemical characterization of the electrodes was performed under a three-electrode
configuration. Measurement of current-voltage characteristics and electrochemical impedance
spectra was performed using an Autolab PGSTAT302 (Metrohm) over a range of temperatures (600-
700 °C) under a hydrogen-nitrogen gas mixture humidified with water at room temperature
(H2:H2O:N2 = 48.5:3.0:48.5). The efficacy of our three-electrode measurement was demonstrated by
Lomberg et al. [38]
3. 3D Imaging and Reconstruction
In our previous report, we successfully imaged nickel-infiltrated GDC electrodes with 5 nm
resolution and then reconstructed and quantified the electrode microstructures [12]. The process for
the SEM sample preparation and 3D imaging is briefly summarized below.
After the electrochemical measurements, the anode samples were impregnated with epoxy
resin (Specifix20, Struers) under vacuum conditions in order to minimize the undesirable damage on
the specimen and to avoid accumulation of gallium ions in the pores during FIB milling, as well as to
help distinguish the pores from the solid phases in SEM imaging. The cured samples were cut and
mechanically polished, mounted onto a specimen stub with silver paste, and sputtered with gold to
ensure sufficient electron conductivity. The 3D microstructure of the anodes was imaged with an
Auriga (Zeiss) FIB-SEM system equipped with a backscattered electron detector, which enables to
clearly distinguish the two solid phases in the SEM images. Regions were selected for
microstructural analysis and went through the following image processing using Avizo (FEI): (i)
alignment of the stack images using the least square method, (ii) noise reduction using the edge
preserving smoothing filter (a combination of the Canny filter and the Gaussian smoothing filter) and
(iii) segmentation using a 2D histogram segmentation algorithm based on the water shed algorithm,
followed by manual correction. Then, the 3D porous microstructure was virtually reconstructed,
from which various microstructural parameters, such as phase volume fractions, surface area,
particle/pore sizes, phase connectivity and tortuosity factor, were quantified. Volume fractions were
evaluated by counting the number of voxels corresponding to each phase, followed by division by
the total number of voxels in the reconstructed volume [11]. Surface area was measured by the
marching cube algorithm and then used to obtain the GDC-Pore double-phase boundary SDPBv as
follows:
SDPBv =
SGDC+SPore−S¿
2V(1)
where Si is the total surface area of phase i and V is the entire reconstructed volume. Particle/pore
sizes were measured using the 3D mean intercept method, the 2D version of which was originally
proposed by Simwonis et al. [39]. This 3D mean intercept method is also a simplified approach of
the ray-shooting method [40]. Tortuosity factors were measured by the diffusion-based method [23].
Connectivity was judged based on the 6-neighboring voxel connection using an in-house image
processing program.
4. Numerical Modeling
A 1D numerical simulation model was developed to predict the electrochemical performance
of the Ni-GDC electrodes. Conservation of electrons, ions and gas species were considered, and were
coupled by the electrochemical oxidation of hydrogen. Since GDC is a mixed ionic electronic
conductor (MIEC) in the fuel environment, the electrochemical reaction was assumed to occur at the
contact surface between GDC and pore, i.e. double-phase boundaries (DPBs). This assumption,
considered reasonable according to the experimental works in literature [5–8], is one of the
distinguishing features of Ni-GDC anodes. Microstructural parameters obtained from the real porous
microstructure were used to evaluate the effective transport rates and the electrochemical activity
within the electrodes.
Conservation of electrons and oxide ions was described as follows using the electrochemical
potential of the charge carriers ~μi:
∇⋅ ¿ (2)
∇⋅ ¿ (3)
where σ e¿ ¿ and σ O¿¿ are the effective electronic and ionic conductivities, and ict is the volumetric
density of the charge-transfer current.
The dusty-gas model [41,42] was used to solve multi-component gas diffusion in the porous
anodes.
∇⋅N i=z i ict
F(4)
N i
Di , Keff +∑
j≠ i
X j N i−X i N j
Dijeff =
−Pt
RT∇X i−
X i
RT (1+K P t
μD i ,Keff )∇Pt (5)
where z i is the stoichiometric coefficient (−1, +1 and 0 for hydrogen, steam and nitrogen,
respectively), X i, Pi and N i are the molar fraction, partial pressure and molar flux of gas species i,
respectively. Pt is the total pressure, while μ and K are the mixture viscosity and permeability, and
Di , Keff and Dij
eff are the effective Knudsen and molecular diffusion coefficients, respectively.
The effective conductivities and diffusivities in eq. 2, 3 and 5 were estimated by modifying
bulk properties with the quantified volume fractions V i and tortuosity factors τ i:
σe¿=
V ¿
τ¿σ
e ¿+V GDC
τ GDCσ e¿ ¿¿
¿σ
O¿=V GDC
τGDCσ O¿¿ ¿D
eff =V Pore
τ PoreD
(6)
Bulk conductivities and diffusivities were evaluated as follows [3,43–45].
σ e¿=3.27 ×106−1065.3T ¿ (7)
σe¿=3.456 ×1011
T exp(−2.388× 105
RT )PO 2
¿ −0.25¿ (8)
σO¿=1.09 × 107
T exp (−6.175× 104
RT )¿ (9)
Dij=
0.01013T 1.75( 1M i×103 +
1M j ×103 )
1 /2
Pt [( Σ v i× 106 )1 /3+(Σ v j× 106 )1 /3 ]2
(10)
Di , K=dpore
3 √ 8 RTπ M i
(11)
where M i and Σ v i are the molecular mass and the diffusion volume of gas species i, respectively.
The local oxygen partial pressure (or activity) in the solid GDC phase used in eq. 8 is
obtained by assuming the following local equilibrium [26], as there is no electrochemical reaction
taking place inside the solid phase:
~μO 2−¿−2~μe−¿=μO=1
2RT ln PO2
¿ ¿¿ (12)
The electrochemical oxidation of hydrogen was assumed to occur at the DPB [5–8], and
described by the Butler-Volmer equation, where the exchange current density is considered as a
function of the DPB density SDPBv .
ict=i0 , DPB SDPBv {exp ( F
RTηact)−exp(−F
RTηact)} (13)
The exchange current density per unit DPB surface area i0 , DPB, or the surface exchange
coefficient, was assumed to be a function of the local oxygen partial pressure [5, 8, 37].
i0 , DPB=5.9 ×107 PO2
−0.25 exp(−2.1 ×105
RT ) (14)
where the pre-exponent constant and the activation energy terms were determined so as to match the
numerically predicted overpotential characteristics to the experimental results. It should be noted that
the PO2
−0.25 dependence was originally obtained from a samarium-doped ceria (SDC) electrode; this is
a temporary treatment due to the lack of experimental data related to hydrogen oxidation kinetics on
GDC surfaces. The activation energy was similar to the value reported by Lai and Haile for SDC
(2.67 eV = 2.57 ×105 J mol-1 K-1) [5]. The oxygen partial pressure used in eq. (14) is estimated from
the gas-phase equilibrium and different from that obtained from eq. (12).
Local activation overpotential ηact and concentration overpotential ηcon were expressed as
follows:
ηact=−12 F
¿ (15)
ηcon=−RT
2 Fln( PH 2
PH 2
bulk
PH 2 Obulk
PH 2 O ) (16)
where ΔG0 is the standard Gibbs free energy associated with the hydrogen oxidation reaction, and
Pibulk is the gas partial pressure on the anode surface. The total anode overpotential can be expressed
as follows:
ηt=−12 F
¿ (17)
where CC denotes the current collector side, and I the anode-electrolyte interface side.
5. Results and Discussion
5.1 Microstructure
Fig. 1 shows one of the cross-sectional SEM images, its histogram and the segmented image.
By using lower acceleration voltage of the electron beam (1.5 keV), the particles were imaged with
12.5 nm3 voxel size. As can be seen from the histogram, the three phases were clearly distinguished
using the back-scattering electron detector. This clear contrast enabled precise image segmentation
using the 2D histogram segmentation algorithms. In the segmented images, the white, gray and black
regions correspond to GDC, Ni and pore phase, respectively. Fig. 2 shows the reconstructed
structures of the infiltrated Ni-GDC anode. The reconstructed size was 9.38 x 5.63 x 9.65 m3.
Table 1 shows the quantified microstructural parameters. In order for the reconstructed
volume to be representative of the whole anode structure, the structure needs to contain a certain
number of particles/pores in each direction. Given the largest characteristic length scale of the anode
structure is found in the GDC phase (1.23 μm), the reconstructed structure has 7.63, 4.58 and 7.85
particles in each direction, which is considered to be large enough based on the analysis by Cai et al
[34]. Also, for the precise quantification of the microstructural parameters, characteristic features of
the anode need to be represented by sufficient number of image elements (voxels). Given the
smallest characteristic length scale is found in the pore phase (0.341 μm), the particle and pores are
resolved by at least 27 voxels in each direction. This is also sufficient to accurately quantify the
microstructural parameters [34].
Fig. 1 FIB imaging of a Ni-GDC electrode and the image segmentation.
Fig. 2 Reconstructed 3D microstructure of the three phases.
Table 1 Microstructural parameters.
The nickel particle size found in the infiltrated electrode was much smaller than that in the
conventional electrodes [23], which is one of the advantages of the infiltration technique. However,
due to the lower volume fraction of the phase, there was limited percolation in the nickel phase. In
this case the nickel tortuosity factor becomes indefinite, and hence the effective electronic
conductivity (eq. 6) is determined by that of the GDC phase. Note that the electronic conductivity of
the GDC phase is still one or two orders of magnitude larger than the ionic conductivity of the phase.
Therefore the distribution of the electrochemical reaction is likely to be determined by the ionic
conduction [25], and the effect of the electronic conduction is limited. Although not all of the nickel
particles are percolated to form electronic conduction pathways, they still serve as a catalyst for the
dissociative adsorption of hydrogen molecules. In the anode used in this study, the nickel particles
are homogeneously distributed within the GDC scaffold. Therefore the supply of the adsorbed
hydrogen atoms to the reaction sites is considered to be sufficient, and less likely to be the rate-
determining process.
5.2 Simulation
Table 2 summarizes the default computational parameters. The microstructural parameters used in
eq. 6 and 13 are taken from Table 1. Fig. 3 shows the comparison of the anode overpotential between
the experiment and the simulation under three different temperature conditions with the anode fuel
composition of H2:H2O:N2 = 48.5:3.0:48.5. It was found that the numerical results have a reasonable
agreement with the experimental results at 700 °C and 650 °C, whereas the curvature in the
overpotential characteristics is not fully reproduced, especially at increasing current density at
600 °C. There are several reasons that can explain the discrepancies: (i) the electrochemical reaction
model described by the Butler-Volmer equation (eq. 13 and 14) oversimplifies the complex reaction
kinetics around the reaction sites. Similar discrepancies have also been found in the case of Ni-YSZ
electrode simulation [11]. (ii) The assumption that the entire DPB is active for the reaction may not
be always accurate; instead, the reaction may be localized around the TPB lines, i.e. an “extended
TPB area”. This may become significant at lower temperature due to the smaller electronic
conductivity in the GDC phase. However its width from the TPB line is currently not clear. (iii) The
contribution of the isolated nickel phase was not taken into account in the 1D model with the
homogenization approach. However such a phase might alter the migration pathways of the electrons
and affect the reaction distribution within the electrode.
Table 2 Default computational parameters.
Fig. 3 Comparison of the anode polarization overpotential between simulation and experiment.
In order to improve the accuracy of the model, the kinetics of adsorption and desorption of
gas species on nickel and GDC surfaces can be included; examples of such approach are found in
literature [46–48]. However, this will introduce a number of unknown parameters, such as the total
adsorption site density and equilibrium coverage, and may increase uncertainty of the model. The
model presented in this study is intended to simulate electrochemical behavior of Ni-GDC electrodes
with a minimum number of fitting parameters.
The electrode performance is significantly influenced by the electrode microstructure through
species transport and electrochemical reaction; therefore optimization of the microstructure is
required to improve electrode performance and durability. However, it is difficult to enhance both
the transport and electrochemical properties of the electrodes at the same time because these are
inherently coupled and sometimes in conflict with each other. For example, reducing the particle size
helps to increase the number of reaction sites, i.e., the DPB density, however it also reduces the pore
size, increasing the gas diffusion resistance. Therefore the sensitivity of the electrode performance to
the microstructural parameters needs to be understood in order to determine which parameter needs
to be prioritized for microstructural optimization. In this study the electrode area-specific resistance
(ASR) was chosen as a performance indicator and its sensitivity to the electrode microstructure, such
as DPB density, GDC tortuosity factor and mean pore size, was investigated to provide insights into
possible strategies to improve electrodes.
Fig. 4 shows the sensitivity of the area-specific resistance to the DPB density at different
current densities. The DPB density was varied from 10-2 to 102 μm2 μm-3, and the current density
from 10 to 300 mA cm-2 at 700 °C. The ASR values are shown in the log scale. Overall, the area-
specific resistance decreases as the DPB density increases. Also, the sensitivity to the DPB density is
significantly higher in the region where the DPB density is smaller than ca. 1 μm2 μm-3. The point at
which the area-specific resistance becomes almost stable is not significantly affected by the current
density. Increasing the current density decreases the area-specific resistance in the higher current
density region when the DPB density is lower than ca. 0.1 μm2 μm-3. This may be due to the
nonlinearity of the electrochemical reaction kinetics employed in this model. Considering the fact
that the DPB density quantified from the reconstructed anode is 2.13 μm2 μm-3, the electrode
performance can still be improved if the DPB density is increased; a 10% increase in the DPB
density would result in 10% decrease of the area-specific resistance.
Fig. 4 Effect of DPB density on the anode area-specific resistance at 700 °C.
Fig. 5 shows the sensitivity of the area-specific resistance to the GDC tortuosity factor at
different current densities. The GDC tortuosity factor was varied from 1 to 10, and current density
from 10 to 300 mA cm-2 at 700 °C. Regardless of the current density, the area-specific resistance of
the anode decreases as the tortuosity factor decreases, which is not surprising as the lower tortuosity
factor decreases the Ohmic resistance associated with both electron and ion conduction.
Fig. 5 Effect of GDC tortuosity factor on the anode area-specific resistance at 700 °C.
Gas diffusion in the porous material with submicron scale pores is influenced by the Knudsen
diffusion because the characteristic length scale of the pores is comparable to or smaller than the
mean free path length of the gas molecules. According to eq. 11, the Knudsen diffusivity linearly
depends on the mean pore size and becomes significantly smaller than the molecular diffusivity
(eq. 10) when the pore size is small. The sensitivity analysis on the DPB density indicated that the
smaller characteristic length scale of the porous electrode may help enhance the electrochemical
reaction rate by increasing the reaction site density. However, the smaller characteristic length scale
is likely to inhibit gas diffusion through the electrode.
Prior to analysis of the area-specific resistance, the dependency of the gas diffusivities on the
mean pore size is investigated. For this purpose “mean gas diffusivity” in a gas mixture is defined as
follows. First, the DGM model (eq. 5) is analytically transformed to an explicit form of the molar
flux as follows:
N i=−∑j=1
n hij−1
RT (∇P j+K P j
μ D j , Keff ∇Pt) (18)
where the matrix H (with components of hij) is defined as follows with gas diffusivities and molar
fractions:
hij=[ 1Di , K
eff + ∑k=1 ,k ≠ i
n X k
Dikeff ]δ ij+( δij−1 )
X i
Dijeff (19)
where δ ij is the Kronecker delta. The mean gas diffusivity D is then defined using the Frobenius
norm of the matrix H :
D= 1‖H‖F
= 1
√∑i
n
∑j
n
|hij|2 (20)
The dependency of the mean gas diffusivity on the mean pore size is shown in Fig. 6, as well
as that of the Knudsen diffusivities and the molecular diffusivities. Overall, there are two distinct
regions found in the graph. In the region where the pore size is larger, the mean gas diffusivity is
almost constant and comparable to the molecular diffusivities. This is because the molecular
diffusion is dominant in such a scale. On the other hand, it asymptotically approaches the Knudsen
diffusivities as the pore size becomes smaller, which indicates that Knudsen diffusion dominates
mass transfer in the region. The intermediate region appears around a mean pore size of 1 μm.
Fig. 7 shows the effect of the mean pore size on the anode area-specific resistance at the same
range of pore sizes. The area specific resistance of the electrode reflects the behavior of the mean gas
diffusivity. The current density was varied from 10 to 300 mA cm-2 at 700 °C. In the molecular-
diffusion-dominant region, the area-specific resistance is not considerably influenced by the mean
pore size. On the other hand in the Knudsen-diffusion-dominant region the value gradually increases
due to the decrease in the mean diffusivity. The effect of Knudsen diffusion begins to appear at the
mean pore size range of 1 μm when the current density is higher, but around 0.1 μm when the current
density is lower. This is because the higher current density requires faster fuel diffusion through the
porous electrode and hence the electrode performance is likely to be more sensitive to the difference
in gas diffusivity. Therefore it is recommended for SOFC anodes to have pores with the size of at
least 1 μm particularly when SOFC systems are operated at high fuel consumption rates; otherwise
gas transport in the pores are governed by the Knudsen diffusion and the electrode performance
significantly decreases.
Fig. 6 Effect of the mean pore size on the diffusion coefficients at 700 °C.
Fig. 7 Effect of the mean pore size on the anode area-specific resistance at 700 °C.
The variation in the area-specific resistance in the sensitivity analysis was largest when the
DPB density was varied, spanning two orders of magnitude, whereas values remained in the same
order of magnitude when the GDC tortuosity factor and the mean pore size were varied. This
indicates that the electrochemical reaction on the DPB is rate-limiting in these Ni-GDC anodes.
Similar trends were also observed experimentally by Nakamura et al [7]. Therefore, increasing the
DPB density in Ni-GDC electrodes is confirmed to be the most effective approach to improve
electrode performance, when compared to improving species transport through the electrode.
Decreasing the primary particle size of the GDC phase is one of the ways to achieve this. However,
smaller particle sizes inevitably decrease the pore size, which inhibits gas diffusion through the
electrodes. Therefore adding pore former, such as carbon black or other organic nano particles,
would be effective to keep the pore size no less than few hundred nanometers to avoid Knudsen
diffusion in the gas diffusion process. Note that the smaller GDC particle size does not increase the
tortuosity factor of the phase because theoretically the geometrically analogous structures have the
same tortuosity factors. Although adding pore former changes the geometry of the electrode and
hence may increase the GDC tortuosity factor, the amount of the increase needs to be limited to
avoid an increase in the Ohmic loss associated with the ion conduction. These insights and directions
obtained in this study are expected to be useful in the future attempt to further optimize the electrode
microstructures.
6. Conclusions
A one-dimensional numerical model of Ni-GDC electrodes has been developed to analyze the
effect of the electrode microstructure on performance. The electrode microstructure was obtained
with FIB-SEM tomography and the microstructural parameters were quantified and applied to a
numerical model to evaluate the transport and electrochemical properties. GDC was considered as a
mixed conductor and hence the electrochemical reaction was assumed to occur on the entire GDC-
pore contact area (DPB). The numerical model successfully reproduced the overpotential
characteristics measured at 700 °C and 650 °C, though the curvature of the graph was not as well
reproduced at 600 °C at high current density (>150 mA cm-2). The contribution of the nickel phase to
help local electron conduction may need to be taken into account to improve the accuracy of the
model. A sensitivity analysis was also conducted at 700 °C to investigate the effect of electrode
microstructure on electrode performance. This revealed that the electrochemical reaction on the DPB
is the rate-determining process within the electrodes; therefore increasing the DPB density is
recommended as the most effective route to improving performance of ceria-based electrodes, rather
than improving species transport rate. The model developed in this study offers a basis to understand
the microstructure-performance relationships in Ni-GDC electrodes, which is useful to further
optimize their porous microstructures.
Acknowledgments
The authors would like to acknowledge the financial support from Japan Society for the Promotion
of Science (JSPS), Alan Howard scholarship and Engineering and Physical Sciences Research
Council (EPSRC) grant number EP/I037016/1.
Nomenclature
d pore pore size (m)
Dij binary molecular diffusivity (m2 s-1)
DK Knudsen diffusivity (m2 s-1)
D mean diffusivity (m2 s-1)
F Faraday constant (C mol-1)
G Gibbs free energy (J mol-1)
i0 , DPB exchange current per unit DPB area (A m-2)
ict charge-transfer current (A m-3)
K permeability (m2)
L anode thickness (m)
M i molecular weight (kg mol-1)
N i molar flux (mol m-2 s-1)
Pi partial pressure (Pa)
Pt total pressure (Pa)
R gas constant (J mol-1 K-1)
Si surface area (m2)
T temperature (K)
V volume (m3)
V i volume fraction (-)
X i molar fraction (-)
z i stoichiometric coefficient (-)
Greek symbols
δ ij Kronecker delta
η overpotential (V)
μ viscosity (Pa s)
μi chemical potential (J mol-1)~μi electrochemical potential (J mol-1)
σ conductivity (m2 s-1)
Σ v i diffusion volume (m3)
τ i tortuosity factor
Subscripts
act activation
CC current collector
con concentration
ct charge-transfer
DPB double-phase boundary
I anode-electrolyte interface
t total
Superscripts
bluk value for bulk material
eff effective value for porous material
v volumetric
References
[1] H.L. Tuller, A.S. Nowick, Small polaron electron transport in reduced CeO2 single crystals, J.
Phys. Chem. Solids. 38 (1977) 859–867. doi:10.1016/0022-3697(77)90124-X.
[2] K. Eguchi, T. Setoguchi, T. Inoue, H. Arai, Electrical properties of ceria-based oxides and
their application to solid oxide fuel cells, Solid State Ionics. 52 (1992) 165–172.
doi:10.1016/0167-2738(92)90102-U.
[3] B.C.H. Steele, Appraisal of Ce1-yGdyO2-y/2 electrolytes for IT-SOFC operation at 500 C,
Solid State Ionics. 129 (2000) 95–110. doi:10.1016/S0167-2738(99)00319-7.
[4] E. Ruiz-Trejo, J. Maier, Electronic Transport in Single Crystals of Gd-Doped Ceria, J.
Electrochem. Soc. 154 (2007) B583. doi:10.1149/1.2722530.
[5] W. Lai, S.M. Haile, Impedance Spectroscopy as a Tool for Chemical and Electrochemical
Analysis of Mixed Conductors: A Case Study of Ceria, J. Am. Ceram. Soc. 88 (2005) 2979–
2997. doi:10.1111/j.1551-2916.2005.00740.x.
[6] T. Nakamura, T. Kobayashi, K. Yashiro, A. Kaimai, T. Otake, K. Sato, et al., Electrochemical
Behaviors of Mixed Conducting Oxide Anodes for Solid Oxide Fuel Cell, J. Electrochem.
Soc. 155 (2008) B563. doi:10.1149/1.2901047.
[7] T. Nakamura, K. Yashiro, A. Kaimai, T. Otake, K. Sato, T. Kawada, et al., Determination of
the Reaction Zone in Gadolinia-Doped Ceria Anode for Solid Oxide Fuel Cell, J.
Electrochem. Soc. 155 (2008) B1244. doi:10.1149/1.2975322.
[8] W.C. Chueh, W. Lai, S.M. Haile, Electrochemical behavior of ceria with selected metal
electrodes, Solid State Ionics. 179 (2008) 1036–1041. doi:10.1016/j.ssi.2007.12.087.
[9] J.R. Wilson, W. Kobsiriphat, R. Mendoza, H.-Y. Chen, J.M. Hiller, D.J. Miller, et al., Three-
dimensional reconstruction of a solid-oxide fuel-cell anode., Nat. Mater. 5 (2006) 541–544.
doi:10.1038/nmat1668.
[10] H. Iwai, N. Shikazono, T. Matsui, H. Teshima, M. Kishimoto, R. Kishida, et al.,
Quantification of SOFC anode microstructure based on dual beam FIB-SEM technique, J.
Power Sources. 195 (2010) 955–961. doi:10.1016/j.jpowsour.2009.09.005.
[11] M. Kishimoto, H. Iwai, M. Saito, H. Yoshida, Quantitative evaluation of solid oxide fuel cell
porous anode microstructure based on focused ion beam and scanning electron microscope
technique and prediction of anode overpotentials, J. Power Sources. 196 (2011) 4555–4563.
doi:10.1016/j.jpowsour.2010.12.100.
[12] M. Kishimoto, M. Lomberg, E. Ruiz-trejo, N.P. Brandon, Enhanced triple-phase boundary
density in infiltrated electrodes for solid oxide fuel cells demonstrated by high-resolution
tomography, J. Power Sources. 266 (2014) 291–295. doi:10.1016/j.jpowsour.2014.05.038.
[13] N. Vivet, S. Chupin, E. Estrade, T. Piquero, P.L. Pommier, D. Rochais, et al., 3D
Microstructural characterization of a solid oxide fuel cell anode reconstructed by focused ion
beam tomography, J. Power Sources. 196 (2011) 7541–7549.
doi:10.1016/j.jpowsour.2011.03.060.
[14] J. Joos, T. Carraro, A. Weber, E. Ivers-Tiffée, Reconstruction of porous electrodes by
FIB/SEM for detailed microstructure modeling, J. Power Sources. 196 (2011) 7302–7307.
doi:10.1016/j.jpowsour.2010.10.006.
[15] F. Tariq, M. Kishimoto, V. Yufit, G. Cui, M. Somalu, N.P. Brandon, 3D imaging and
quantification of interfaces in SOFC anodes, J. Eur. Ceram. Soc. 34 (2014) 3755–3761.
doi:10.1016/j.jeurceramsoc.2014.05.003.
[16] P.R. Shearing, J. Gelb, N.P. Brandon, X-ray nano computerised tomography of SOFC
electrodes using a focused ion beam sample-preparation technique, J. Eur. Ceram. Soc. 30
(2010) 1809–1814. doi:10.1016/j.jeurceramsoc.2010.02.004.
[17] P.R. Shearing, J. Gelb, J. Yi, W.-K. Lee, M. Drakopolous, N.P.P. Brandon, Analysis of triple
phase contact in Ni–YSZ microstructures using non-destructive X-ray tomography with
synchrotron radiation, Electrochem. Commun. 12 (2010) 1021–1024.
doi:10.1016/j.elecom.2010.05.014.
[18] P.R. Shearing, R.S. Bradley, J. Gelb, F. Tariq, P.J. Withers, N.P. Brandon, Exploring
microstructural changes associated with oxidation in Ni–YSZ SOFC electrodes using high
resolution X-ray computed tomography, Solid State Ionics. 216 (2012) 69–72.
doi:10.1016/j.ssi.2011.10.015.
[19] J. Laurencin, R. Quey, G. Delette, H. Suhonen, P. Cloetens, P. Bleuet, Characterisation of
Solid Oxide Fuel Cell Ni–8YSZ substrate by synchrotron X-ray nano-tomography: from 3D
reconstruction to microstructure quantification, J. Power Sources. 198 (2012) 182–189.
doi:10.1016/j.jpowsour.2011.09.105.
[20] G.J. Nelson, W.M. Harris, J.J. Lombardo, J.R. Izzo, W.K.S. Chiu, P. Tanasini, et al.,
Comparison of SOFC cathode microstructure quantified using X-ray nanotomography and
focused ion beam-scanning electron microscopy, Electrochem. Commun. 13 (2011) 586–589.
doi:10.1016/j.elecom.2011.03.016.
[21] V. Julie, L. Jérôme, C. Peter, B. Pierre, D. Gérard, S. Heikki, et al., 3D phase mapping of solid
oxide fuel cell YSZ/Ni cermet at the nanoscale by holographic X-ray nanotomography, J.
Power Sources. 243 (2013) 841–849. doi:10.1016/j.jpowsour.2013.06.069.
[22] M. Kishimoto, H. Iwai, M. Saito, H. Yoshida, Three-Dimensional Simulation of SOFC Anode
Polarization Characteristics Based on Sub-Grid Scale Modeling of Microstructure, J.
Electrochem. Soc. 159 (2012) B315–B323. doi:10.1149/2.086203jes.
[23] M. Kishimoto, H. Iwai, K. Miyawaki, M. Saito, H. Yoshida, Improvement of the sub-grid-
scale model designed for 3D numerical simulation of solid oxide fuel cell electrodes using an
adaptive power index, J. Power Sources. 223 (2013) 268–276.
doi:10.1016/j.jpowsour.2012.09.077.
[24] M. Kishimoto, K. Miyawaki, H. Iwai, M. Saito, H. Yoshida, Effect of Composition Ratio of
Ni-YSZ Anode on Distribution of Effective Three-Phase Boundary and Power Generation
Performance, Fuel Cells. 13 (2013) 476–486. doi:10.1002/fuce.201200174.
[25] K. Miyawaki, M. Kishimoto, H. Iwai, M. Saito, H. Yoshida, Comprehensive understanding of
the active thickness in solid oxide fuel cell anodes using experimental, numerical and semi-
analytical approach, J. Power Sources. 267 (2014) 503–514.
doi:10.1016/j.jpowsour.2014.05.112.
[26] N. Shikazono, D. Kanno, K. Matsuzaki, H. Teshima, S. Sumino, N. Kasagi, Numerical
Assessment of SOFC Anode Polarization Based on Three-Dimensional Model Microstructure
Reconstructed from FIB-SEM Images, J. Electrochem. Soc. 157 (2010) B665–B672.
doi:10.1149/1.3330568.
[27] K. Matsuzaki, N. Shikazono, N. Kasagi, Three-dimensional numerical analysis of mixed ionic
and electronic conducting cathode reconstructed by focused ion beam scanning electron
microscope, J. Power Sources. 196 (2011) 3073–3082. doi:10.1016/j.jpowsour.2010.11.142.
[28] D. Kanno, N. Shikazono, N. Takagi, K. Matsuzaki, N. Kasagi, Evaluation of SOFC anode
polarization simulation using three-dimensional microstructures reconstructed by FIB
tomography, Electrochim. Acta. 56 (2011) 4015–4021. doi:10.1016/j.electacta.2011.02.010.
[29] T. Carraro, J. Joos, B. Rüger, A. Weber, E. Ivers-Tiffée, 3D finite element model for
reconstructed mixed-conducting cathodes: I. Performance quantification, Electrochim. Acta.
77 (2012) 315–323. doi:10.1016/j.electacta.2012.04.109.
[30] T. Carraro, J. Joos, B. Rüger, A. Weber, E. Ivers-Tiffée, 3D finite element model for
reconstructed mixed-conducting cathodes: II. Parameter sensitivity analysis, Electrochim.
Acta. 77 (2012) 309–314. doi:10.1016/j.electacta.2012.04.163.
[31] J. Joos, M. Ender, T. Carraro, A. Weber, E. Ivers-Tiffée, Representative volume element size
for accurate solid oxide fuel cell cathode reconstructions from focused ion beam tomography
data, Electrochim. Acta. 82 (2012) 268–276. doi:10.1016/j.electacta.2012.04.133.
[32] A. Häffelin, J. Joos, M. Ender, A. Weber, E. Ivers-Tiffée, Time-Dependent 3D Impedance
Model of Mixed-Conducting Solid Oxide Fuel Cell Cathodes, J. Electrochem. Soc. 160 (2013)
F867–F876. doi:10.1149/2.093308jes.
[33] P.R. Shearing, Q. Cai, J.I. Golbert, V. Yufit, C.S. Adjiman, N.P. Brandon, Microstructural
analysis of a solid oxide fuel cell anode using focused ion beam techniques coupled with
electrochemical simulation, J. Power Sources. 195 (2010) 4804–4810.
doi:10.1016/j.jpowsour.2010.02.047.
[34] Q. Cai, C.S. Adjiman, N.P. Brandon, Modelling the 3D microstructure and performance of
solid oxide fuel cell electrodes: Computational parameters, Electrochim. Acta. 56 (2011)
5804–5814. doi:10.1016/j.electacta.2011.04.065.
[35] Q. Cai, C.S. Adjiman, N.P. Brandon, Investigation of the active thickness of solid oxide fuel
cell electrodes using a 3D microstructure model, Electrochim. Acta. 56 (2011) 10809–10819.
doi:10.1016/j.electacta.2011.06.105.
[36] W.C. Chueh, Y. Hao, W. Jung, S.M. Haile, High electrochemical activity of the oxide phase
in model ceria-Pt and ceria-Ni composite anodes., Nat. Mater. 11 (2012) 155–61.
doi:10.1038/nmat3184.
[37] F. Ciucci, W.C. Chueh, D.G. Goodwin, S.M. Haile, Surface reaction and transport in mixed
conductors with electrochemically-active surfaces: a 2-D numerical study of ceria., Phys.
Chem. Chem. Phys. 13 (2011) 2121–35. doi:10.1039/c0cp01219j.
[38] M. Lomberg, E. Ruiz-Trejo, G. Offer, N.P. Brandon, Characterization of Ni-Infiltrated GDC
Electrodes for Solid Oxide Cell Applications, J. Electrochem. Soc. 161 (2014) F899–F905.
doi:10.1149/2.0501409jes.
[39] D. Simwonis, F. Tietz, D. Stover, Nickel coarsening in annealed Ni / 8YSZ anode substrates
for solid oxide fuel cells, Solid State Ionics. 132 (2000) 241–251. doi:10.1016/S0167-
2738(00)00650-0.
[40] K.N. Grew, Y.S. Chu, J. Yi, A. a. Peracchio, J.R. Izzo, Y. Hwu, et al., Nondestructive
Nanoscale 3D Elemental Mapping and Analysis of a Solid Oxide Fuel Cell Anode, J.
Electrochem. Soc. 157 (2010) B783. doi:10.1149/1.3355957.
[41] E.A. Mason, Flow and Diffusion of Gases in Porous Media, J. Chem. Phys. 46 (1967) 3199.
doi:10.1063/1.1841191.
[42] D. Arnošt, P. Schneider, Dynamic transport of multicomponent mixtures of gases in porous
solids, Chem. Eng. J. 57 (1995) 91–99. doi:10.1016/0923-0467(94)02900-8.
[43] N.F. Bessette II, W.J. Wepfer, J. Winnick, A Mathematical Model of a Solid Oxide Fuel Cell,
J. Electrochem. Soc. 142 (1995) 3792–3800.
[44] E.N. Fuller, P.D. Schettler, J.C. Giddings, A New Method for Prediction of Binary Gas-Phase
Diffusion Coefficients, Ind. Eng. Chem. 58 (1966) 19–27. doi:10.1021/ie50677a007.
[45] W. Kast, C.-R. Hohenthanner, Mass transfer within the gas-phase of porous media, Int. J. Heat
Mass Transf. 43 (2000) 807–823. doi:10.1016/S0017-9310(99)00158-1.
[46] J. Deseure, Y. Bultel, L. Dessemond, E. Siebert, Theoretical optimisation of a SOFC
composite cathode, Electrochim. Acta. 50 (2005) 2037–2046.
doi:10.1016/j.electacta.2004.09.012.
[47] J. Deseure, Y. Bultel, L. Dessemond, E. Siebert, Modelling of dc and ac responses of a planar
mixed conducting oxygen electrode, Solid State Ionics. 176 (2005) 235–244.
doi:10.1016/j.ssi.2004.07.018.
[48] H. Zhu, R.J. Kee, V.M. Janardhanan, O. Deutschmann, D.G. Goodwin, Modeling Elementary
Heterogeneous Chemistry and Electrochemistry in Solid-Oxide Fuel Cells, J. Electrochem.
Soc. 152 (2005) A2427. doi:10.1149/1.2116607.
top related