im 154-8 pn/dp cpu interface module - siemens ag · pdf filepreface im 154-8 pn/dp cpu...
Post on 30-Mar-2018
227 Views
Preview:
TRANSCRIPT
IM 154-8 PN/DP CPU interface
module
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
______________________________
___________________
SIMATIC
ET 200pro IM 154-8 PN/DP CPU interface module
Operating Instructions
06/2010 A5E00860134-02
Preface
Description
1
Operating and display elements
2
Communication
3
PROFINET
4
Memory concept
5
Installing and connecting
6
Addressing
7
Commissioning
8
Maintenance and service
9
Debugging functions, diagnostics and troubleshooting
10
Technical specifications
11
Appendix
A
Legal information
Legal information Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products Note the following:
WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks All names identified by are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG Industry Sector Postfach 48 48 90026 NRNBERG GERMANY
A5E00860134-02 08/2010
Copyright Siemens AG 2010. Technical data subject to change
(A) .
IM 154-8 PN/DP CPU interface module Operating Instructions, 06/2010, A5E00860134-02 3
Preface
Purpose of the operating instructions These operating instructions are intended to supplement the ET 200pro Distributed I/O Device (http://support.automation.siemens.com/WW/view/en/21210852) operating instructions. It contains a description of all the functions performed by the IM 154-8 PN/DP CPU interface module. The operating instructions do not include functions that relate generally to ET 200pro. These can be found in the ET 200pro Distributed I/O System operating instructions.
The information contained in these operating instructions and the ET 200pro Distributed I/O Device operating instructions allows you to commission ET 200pro with the IM 154-8 PN/DP CPU interface module and to run it as a DP master or DP slave on the PROFIBUS DP or as an IO controller on the PROFINET.
Basic knowledge required To understand these operating instructions you should have general experience in the field of automation engineering.
Range of validity of these operating instructions These operating instructions apply to the IM 154-8 PN/DP CPU interface module with order number 6ES7154-8AB01-0AB0 and the CM IM PN DP M12, 7/8" terminal module with order number 6ES7194-4AN00-0AA0 and for the components of the ET 200pro distributed I/O device specified in the ET 200pro Distributed I/O Device (http://support.automation.siemens.com/WW/view/en/21210852) operating instructions.
These operating instructions contain a description of the components that was valid at the time of publication. We reserve the right to issue a Product Information which contains up-to-date information about new components and new versions of components.
Note The peculiarities of the failsafe interface module IM 154-8F PN/DP CPU (6ES7154-8FB01-0AB0) can be found as product information on the internet (http://support.automation.siemens.com/WW/view/en/11669702/133300).
http://support.automation.siemens.com/WW/view/en/21210852http://support.automation.siemens.com/WW/view/en/21210852http://support.automation.siemens.com/WW/view/en/11669702/133300
Preface
IM 154-8 PN/DP CPU interface module 4 Operating Instructions, 06/2010, A5E00860134-02
Changes since the previous version In relation to the previous version of this operating instructions ET 200pro Interface Module IM 154-8 CPU (http://support.automation.siemens.com/WW/view/en/24363739), December 2006 edition, the following changes apply.
Increase in performance due to shorter instruction processing times
of the number of blocks that can be monitored by the status block (from 1 to 2)
of the amount of status information that can be monitored with the status block as of STEP7 V5.5
of the number of breakpoints from 2 to 4
of the work memory size
of the local data stack (32 KB per execution level/2 KB per block)
Number of block-related messages (Alarm_S) is uniformly limited to 300
of the length of data to copy (SFC 81) at 512 bytes
Data set routing Encryption of blocks with SIMATIC Block Privacy Expansion of the block number ranges Consistent range of numbers for times and counters Uniform size of data blocks: max. 64 KB Greater BuB performance that can be configured BuB consistency of 240 bytes on the cycle control point Time-delay interrupts: uniform for OB21/OB22 Cyclic interrupts: uniform for OB32 - OB35 Uniform block nesting depth of 16 Number of displayed diagnostic buffer entries in CPU RUN mode is configurable. New function: Reading out service data CBA expansion Expansion of the SFC 12 by 2 new modes to trigger the OB 86 during activation/ deactivation of PROFIBUS slaves or PROFINET IO devices PROFINET Prioritized startup supported
Changing IO Devices in runtime is supported
Device replacement without removable medium
Support of iPar server functionality
Operation of IO devices with user data on slot 0
Support of Isochronous Real Time (IRT)
Support of isochronous real-time communication with "greater flexibility"
Support of isochronous real-time communication with "greater performance"
Support of isochronous mode work at PROFINET
Media redundancy
http://support.automation.siemens.com/WW/view/en/24363739
Preface
IM 154-8 PN/DP CPU interface module Operating Instructions, 06/2010, A5E00860134-02 5
Can be configured as an I device
Shared Device
IP parameters through DCP (Discovery and Configuration Protocol) or SFB 104 "IP_CONF" configurable
Configuration and operation of distributed I/O transfer areas during operation as an I device (direct access of an overlaid OP controller on the local distributed I/O of the IM 154 8 PN/DP CPU as an I device)
Prepared for PROFIenergy when used as an I device (SFB 73 / SFB 74)
Keep Alive Function supported
Additional Web server functionality: Topology display (actual topology and configurable set topology)
Module state
Link between device view in topology and module state
Link to Web servers of other configured devices
Status overview of all configured devices of the PROFINET IO system
Updating of the "Module state" and "Topology" Web pages during activation/deactivation of stations
Automatic page update for all dynamic pages on the Web server
Diagnostic buffer entries and messages can be downloaded as CSV file.
User configurable for login
Connections through http(s)
Displaying the communication connections during open communication (OUC)
Displaying the resources for communication
top related