huang thesis
Post on 14-Apr-2018
239 Views
Preview:
TRANSCRIPT
-
7/30/2019 Huang thesis
1/58
DESIGN AND ANALYSIS OF AN ACTIVE INTEGRATED
ANTENNA
By
Zhuoming Huang
Bachelor of Science
South China University of Technology, 2009
Submitted in Partial Fulfillment of the
Requirements for the Degree of Master of Science in
Electrical Engineering
College of Engineering and Computing
University of South Carolina
2011
Accepted by:
Yinchao Chen, Director of Thesis
Paul Huray, First Reader
Tim Mousseau, Dean of the Graduate School
-
7/30/2019 Huang thesis
2/58
UMI Number: 1492267
All rights reserved
INFORMATION TO ALL USERSThe quality of this reproduction is dependent upon the quality of the copy submitted.
In the unlikely event that the author did not send a complete manuscriptand there are missing pages, these will be noted. Also, if material had to be removed,
a note will indicate the deletion.
UMI 1492267Copyright 2011 by ProQuest LLC.
All rights reserved. This edition of the work is protected againstunauthorized copying under Title 17, United States Code.
ProQuest LLC789 East Eisenhower Parkway
P.O. Box 1346Ann Arbor, MI 48106-1346
-
7/30/2019 Huang thesis
3/58
ii
Copyright by Zhuoming Huang, 2011
All Rights Reserved
-
7/30/2019 Huang thesis
4/58
iii
ACKNOWLEDGEMENTSThis thesis is dedicated to my parents. I would like to express my gratitude to my advisor,
Dr. Yinchao Chen, who has offered me great help and taught me much knowledge in
electrical engineering through the past two years. His attentive assistance in writing this
thesis is heartily acknowledged as well.
Also, I would like to give my thanks to my lab mates, Kangrong Li, Tom McDonough, and
Inpyo Nam. In the past two years, they have given me a lot of helpful advice and study
suggestion in lab meetings and daily discussions.
In addition, all the support from other colleagues and professors and department
officers are as well acknowledged.
-
7/30/2019 Huang thesis
5/58
iv
ABSTRACT
In this thesis, an active integrated antenna (AIA) system is proposed for potential
applications in an RF receiver front end for mobile and wireless communication devices.
The AIA system consists of a microstrip patch antenna and a low noise amplifier (LNA),
which are integrated together with a matching circuit and printed on an FR4 PCB circuit
board. The system is designed, analyzed, and optimized by targeting to satisfy the
design specifications for both the microstrip antenna and the LNA in referencing the
published industrial parameters.
Firstly, the microstrip patch antenna is designed and simulated by the inset feeding
method using Agilent ADS software. The optimized dimensions of the square patch are
1000mil 670 mil with the two smaller feeding patches (400mil 450mil). The center
frequency of the system is 2.45GHz. The objective of this part is to design the antenna
to be suitable for wireless communications characterized with low cost, easy fabrication,
small size, and high efficiency.
Then, the LNA (low-noise amplifier), composed of NE68030 NPN silicon transistor, bias
circuit, and noise matching network, is also studied and designed. It is connected to the
microstrip patch antenna to amplify the signal without adding additional noise. The
target of this design is to ensure the LNA to be with high gain, low noise, high efficiency,
low cost, and to match well with the receiver antenna.
Finally, the microstrip patch antenna and the LNA are integrated together in both the
schematic circuit and layout circuits. The integrated AIA system is further tuned and
optimized for improving the system performance. The achieved results are encouraging
and satisfying and the proposed specifications are essentially met, although the AIA
system may be further improved with consideration of industrial design standards.
-
7/30/2019 Huang thesis
6/58
v
CONTENTSACKNOWLEDGEMENTS ................................................................................................................... iii
ABSTRACT ........................................................................................................................................ iv
Chapter 1 INTRODUCTION ............................................................................................................... 1
1.1 Introduction ........................................................................................................................... 1
1.2 Objective of the research ...................................................................................................... 2
1.3 Outline of the thesis .............................................................................................................. 3
Chapter 2 ANTENNA DESIGN ........................................................................................................... 4
2.1 Antenna theory introduction ................................................................................................ 4
2.2 Microstrip patch antenna fundamentals............................................................................... 5
Chapter 3 DESIGN AND ANALYSIS OF MICROSTRIP PATCH ANTENNA .......................................... 10
3.1 Microstrip Patch Antenna Specifications ............................................................................ 10
3.2 Design Procedure Microstrip Patch Antenna ...................................................................... 13
3.3 Result Analysis of Microstrip Patch Antenna ...................................................................... 23
Chapter 4 LNA DESIGN .................................................................................................................. 24
4.1 LNA Introduction ................................................................................................................. 24
4.1.1 Noise Figure and Noise Temperature ........................................................................... 25
4.1.2 Gain ............................................................................................................................... 26
4.1.3 Standing Wave Ratio .................................................................................................... 26
4.1.4 Return Loss ................................................................................................................... 27
4.1.5 Linearity ........................................................................................................................ 27
4.2 LNA Design Consideration ................................................................................................... 27
4.2.1 Impedance matching .................................................................................................... 27
4.2.2 DC Bias .......................................................................................................................... 28
Chapter 5 DESIGN AND ANALYSIS OF LNA .................................................................................... 30
5.1 Low-noise Amplifier Design Specifications .......................................................................... 30
5.2 Design Procedure of Low-noise Amplifier ........................................................................... 31
5.2.1 Choosing transistor ....................................................................................................... 31
-
7/30/2019 Huang thesis
7/58
vi
5.2.2 Simulation of SP mode Transistor ................................................................................ 31
5.2.3 DC bias circuit ............................................................................................................... 38
5.2.4 Linearity ........................................................................................................................ 42
5.3 Result Analysis of Low-noise Amplifier Design .................................................................... 43
Chapter 6 COMPLETE AIA DESIGN ANALYSIS ................................................................................ 44
Chapter 7 CONCLUSION ................................................................................................................ 47
BIBLIOGRAPHY ............................................................................................................................... 48
-
7/30/2019 Huang thesis
8/58
vii
LIST OF FIGURES
Figure 2.1: inset fed microstrip patch antenna ................................................................. 8
Figure 2.2: equivalent circuit of inset fed microstrip patch antenna ................................ 9
Figure 3.1: parameters setting of substrate layers ........................................................... 13
Figure 3.2: parameters setting of layout layers ................................................................ 14
Figure 3.3: layout design of microstrip patch antenna ..................................................... 15
Figure 3.4: S11 of microstrip patch antenna .................................................................... 16
Figure 3.5: gain, directivity and efficiency of microstrip patch antenna .......................... 17
Figure 3.6: 3D far field radiation pattern of E ................................................................... 18
Figure 3.7: schematic circuits for antenna impedance matching..................................... 19
Figure 3.8: LineCalc for microstrip line calculation ........................................................... 19
Figure 3.9: S11 of matched microstrip patch antenna ..................................................... 20
Figure 3.10: VSWR in 2.45GHz .......................................................................................... 21
Figure 3.11: impedance of matched antenna ................................................................... 22
Figure 4.1: block diagram of an active integrated antenna amplifier receiver front end
........................................................................................................................................... 25
Figure 4.2: current mirror examples [13] ......................................................................... 29
Figure 5.1: schematic circuit of sp-mode scan ................................................................. 32
Figure 5.2: S-parameters of sp-mode ............................................................................... 33
5.3: a single stub matching component is added to the schematic circuit ...................... 34
Figure 5.4: input matching circuit settings ....................................................................... 35
Figure 5.5: input matching network created by smart component ................................. 36
Figure 5.6: S-parameters when input matching network is added .................................. 36
Figure 5.7: schematic circuit when output matching network is added .......................... 37
Figure 5.8: S-parameters when output matching network is added ................................ 38
-
7/30/2019 Huang thesis
9/58
viii
Figure 5.9: bias circuit design schematic .......................................................................... 39
Figure 5.10: noise circles of LNA ....................................................................................... 40
Figure 5.11: S-parameters of LNA design ......................................................................... 41
Figure 5.12: other parameters of LNA design ................................................................... 41
Figure 5.13: Linearity parameters of LNA ......................................................................... 42
Figure 6.1: schematic circuit of the complete AIA design ................................................ 45
Figure 6.2: Layout design of the AIA ................................................................................. 46
Figure 6.3: simulation result of the complete AIA design ................................................ 46
-
7/30/2019 Huang thesis
10/58
1
Chapter 1
INTRODUCTION
1.1 Introduction
The high demands for wireless communications systems in compatibility and efficiency
have been greatly leading to rapid development and growth in the microwave and
monolithic microwave integrated circuit technologies. The active integrated antenna
(AIA), as an advanced solution to various existing problems in wireless communications,
such as noise matching, power saving and size reduction, has been a growing area of
research in recent years.
From a microwave engineers point of view, an AIA can be regarded as an active
microwave circuit, in which the output or input port is free space instead of a
conventional 50 transmission line. In this case, the antenna can provide certain circuit
functions such as resonating, filtering, and duplexing, in addition to its original role as a
radiating element. On the other hand, from an antenna designers point of view, the AIA
is an antenna that possesses built-in signal and wave processing capabilities such as
signal mixing and amplification. [1]
Microstrip patch antennas are extensively used in commercial and military
communication systems. Advantages of using microstrip patch antennas over
conventional antennas are their light weight, low profile and volume, and low cost of
fabrication [4]. However, in comparison to other types of microwave antennas, their
-
7/30/2019 Huang thesis
11/58
2
disadvantages include narrow bandwidth, relatively high loss, low gain, only radiate in
half space, and narrow design tolerance.
The low noise amplifier is an important building block in wireless receivers. It essentially
determines the receivers performance. The LNA design is full of tradeoffs between
optimum gain, optimum input matching, low power consumption, lowest noise figure
and high linearity [5]. Nowadays, wireless communications devices require smaller size,
less power consumption, further reach and wider range receiver front end. Thus, as a
vital part that determines the performance of the receiver front end, the design of LNA
is becoming more and more important.
Normally, there are matching networks between the antenna and the Low-noise
Amplifier in a receiver front end, which are used in microwave circuits to transform the
impedance for eliminating reflection and improving circuit performance such as the gain
or noise figure. The matching network could adjust the output impedance of antenna to
the conjugate of the input impedance of transistor in order to obtain the highest gain; it
could also optimize the LNA to produce the minimum noise figure.
As for the active integrated antenna, instead of the conjugate matching, a transistor is
tested to seek for a better noise figure and higher gain, and then the antenna is
designed to have such output impedance. By this approach, the matching network
between antenna and LNA is omitted.
1.2 Objective of the research
In this research work, the authors major aim is to design an amplifying AIA (active
integrated antenna) working at 2.45 GHz for wireless communications systems. The
proposed AIA include two major components: the microstrip patch antenna and the
low-noise amplifier.
-
7/30/2019 Huang thesis
12/58
3
Firstly, a microstrip patch antenna is analyzed and designed in order for it to take the
basic responsibilities of receiving electromagnetic waves, and transmitting them into
electrical signals. It requires small size, reduced loss, and wide band. Secondly, the LNA
(Low-noise Amplifier) is supposed, designed, and tuned to enhance the signal, reduce
power consumption as well as minimize the noise.
1.3 Outline of the thesis
A brief introduction to antenna theory, including microstrip patch antenna
fundamentals, is presented in chapter 2.
Chapter 3 shows the design details of a single layer microstrip patch antenna. The
antenna is designed to resonate at 2.45GHz, using inset feeding method.
Next, Chapter 4 gives a brief introduction to LNA (low-noise amplifier), especially about
the basic tradeoffs between different amplifying topologies, such as gain, NF (noise
figure), linearity and impedance matching.
Chapter 5 presents the design process of a LNA (low-noise amplifier). The design applied
a NEC product, NE68030 NPN silicon high frequency transistor by using current mirror
circuit as bias current source, as well as input and output matching networks to meet
the specification.
Chapter 6 performs the analysis of the complete design of the amplifying AIA (active
integrated antenna), which is the combination of the microstrip patch antenna and the
LNA (Low-noise Amplifier).
Chapter 7 draws a conclusion on the research work and discuss future possible
development of this area.
-
7/30/2019 Huang thesis
13/58
4
Chapter 2
ANTENNA DESIGN
2.1 Antenna theory introduction
Antenna is defined as a means for radiating or receiving radio waves. In other words,
the antenna is a transitional structure, which turns the electrical signals into
electromagnetic waves [3]. The transmission line is used to transport electromagnetic
energy from the transmitting source to the antenna or from the antenna to the receiver.
Maxwells equations are the core of electromagnetism, also are widely used in antenna
theory.
Table 2.1 Maxwells equations
Differential Form Integral Form Name
Faradays law
Amperes law
Gausss law for electric charge
Gausss law for magnetic charge
-
7/30/2019 Huang thesis
14/58
5
The integral form of Amperes law shows that, in electromagnetic field, the line integral
of the magnetic field intensity over the closed boundary equals to the electrical current
density through the closed circle. The differential form of Amperes law states that, for
any single point in electromagnetic fields, the curl of the magnetic field intensity equals
to the current density through the surface.
Maxwell-Faraday equation presents the relation between the electric field intensity and
the magnetic flux density. The curl of electric field intensity equals to the partial
derivative of magnetic flux density with respect to time.
Gausss law for electric charge explains that in electromagnetic fields, the surface
integral denoting the electric flux through a closed surface equals to the total charge
enclosed by the closed surface. While the Gausss law for magnetism says that the
magnetic field has divergence equal to zero.
Using Maxwells equations to analyze the radiation properties of an antenna, radiation
pattern is commonly applied to examine the directional dependence of the strength of
the radio waves from the antenna or other source. Typically, it is represented by a three
dimensional graph, or polar plots of the horizontal and vertical cross sections.
2.2 Fundamentals of microstrip patch antennas
In high-performance aircraft, spacecraft, satellite and missile applications, where size,
weight, cost, performance, ease of installation, and aerodynamic profile are highly
constrained by their applications, low profile antennas are frequently required. Also,
many government and commercial applications in mobile radio and wireless
communications, are requesting similar specifications for the communication devices.
Compared to other kinds of microwave antennas, microstrip antennas have many
advantages such as light weight, small size, low profile, low cost, easy fabrication and
installation, conformable and planar and nonplanar surfaces, little interference to other
-
7/30/2019 Huang thesis
15/58
6
parts. Thus they are widely used today in many areas, at the frequency from 100MHz to
50 GHz.
However, microstrip antennas also have some disadvantages, like relatively high loss,
low gain, low power, low efficiency, high Q, limited polarization purity, poor scan
performance, spurious feed radiation and very narrow frequency bandwidth.
There are three different types of microstrip patch antennas: microstrip patch antennas,
microstrip travelling wave antennas and microstrip slot antennas. A microstrip patch
antenna consists of a flat rectangular patch of metal, which in practice is usually
mounted over a larger sheet of metal called ground plane. A very thin metallic strip
(patch) is placed a small fraction of a wavelength above a ground plane. The microstrip
patch is designed so its pattern maximum is normal to the patch. The strip (patch) and
the ground plane are separated by a dielectric sheet (referred to as the substrate).
Normally, the dielectric constants of the substrates are chosen in the range of 2.2 to 12.
As designing the microstrip patch antennas, thick substrates and low dielectric constant
provide better efficiency, larger bandwidth, loosely bound fields for radiation into space,
but at the expense of larger element size. On the other hand, thin substrates with higher
dielectric constants are desirable for microwave circuitry because they lead to minimum
undesired radiation and coupling, and smaller element sizes. Since microstrip antennas
are often integrated with other microwave circuitry, a compromise has to be reached
between good antenna performance and circuit design [3].
There are many ways to feed microstrip patch antennas. The most popular ones are the
microstrip line, coaxial probe, aperture coupling and proximity coupling. The microstrip
feed line is also a conducting strip, usually of much smaller width compared to the patch.
Under microstrip line feeding, there are several feeding methods, including probe
feeding via hole, edge feeding and inset feeding.
The inset feeding technique is a direct-coupled feeding method where the input power
is fed to the radiating element directly by a microstrip line type feed line embedded into
-
7/30/2019 Huang thesis
16/58
7
it. In this feed geometry, the feed line directly contacts the patch along the radiating
edge [6]. For the maximum transfer of input power to the antenna, the feed line and
patch input impedances must be matched. Due to the high edge impedance of the
microstrip antenna, the feed line is inset into the patch by a certain distance to match
the antenna input impedance to the line impedance. Actually, the insetting of the feed
line produces lower input impedance than that of the edge of the antenna. The feed line
currents are co-polarized with the current of the resonating patch, which minimizes the
cross polarized radiation [7].
For low frequencies the effective dielectric constant is essentially constant, when the
frequency goes higher, the dielectric constant begins to monotonically increase and
eventually approach the value of the dielectric constant of the substrate. So the initial
values (at low frequencies) of the effective dielectric constant are referred to as the
static values, and they are given as follows [3]:
(2-1)
Since the electrical length of the microstrip antenna is larger than its physical dimension
due to the fringing effects, the extended length of the antenna is usually expressed asfollows [3]:
(2-2)
Thus the length of the patch equals to [3]
(2-3)
As shown in equation 2.4, the resonant frequency of the microstrip antenna is a
function of its length. Since this equation does not account for fringing, it must be
modified to include edge effects.
(2-4)
-
7/30/2019 Huang thesis
17/58
8
Based on the simplified formulation that has been described, we are now able to design
a simple rectangular microstrip patch antenna. We can use the specified information
such as the dielectric constant of the substrate, the resonant frequency, and the height
of the substrate to determine the width and length of the microstrip patch antenna.
Figure 2.1 shows the inset feeding microstrip patch antenna. The input impedance of
the inset feeding microstrip patch antenna mainly depends on the inset distance andto some extent on the inset width (spacing between feeding line and patch conductor).
Variation in the inset length does not produce any change in resonant frequency but a
variation in inset width changes the resonant frequency. Hence the spacing between the
patch conductor and feed line is kept constant, equal to the feed lines width and
variation in the input impedance at resonant frequency with respect to inset length is
studied for various parameters.
Figure 2.1: inset fed microstrip patch antenna
-
7/30/2019 Huang thesis
18/58
9
Assume that the patch is divided into four regions; it can be modeled as transmission
lines loaded by radiating slots of different length as shown in Figure 2.2. Parameters of
each transmission line and the slot are given in Table 2.2. The radiating slots A, B and C
can be modeled as discussed in [8].
Table 2.2 Parameters of elements in the model
Element Width Length
TL1 W SLOT A h W
TL2
SLOT B h
TL3
SLOT C h
Figure 2.2: equivalent circuit of inset fed microstrip patch antenna
-
7/30/2019 Huang thesis
19/58
10
Chapter 3
DESIGN AND ANALYSIS OF
MICROSTRIP PATCH ANTENNA
3.1 Microstrip Patch Antenna Specifications
Reference [2] has proposed some performance characteristics of microstrip patch
antenna in 2.45GHz. By referring its suggestions, the specification and target of the
proposed antenna design are summarized in Table 3.1.
Table 3.1 Required Specifications for microstrip patch antenna
Parameter Specification Unit
Frequency Range 2.44-2.46 GHz
VSWR 5 dB
Bandwidth >30 MHz
Efficiency >75 %
Impedance 50 Ohm
-
7/30/2019 Huang thesis
20/58
11
The center frequency of the antenna is 2.45GHz, which is one of the most commonly
used frequencies in wireless communication. This frequency band is reserved
internationally for the use of radio frequency energy for industrial, scientific and medical
purposes other than communications.
The selected antenna parameters are discussed as follows:
VSWR
In telecommunications, SWR (standing wave ratio) is the ratio of the amplitude of a
partial standing wave at a maximum value to the amplitude at an adjacent minimum
value, in an electrical transmission line.
VSWR (Voltage Standing Wave Ratio) is the parameter to measure the energy consumed
in conductor during electrical signal transmission. It can be expressed by:
For antennas, the lower the VSWR, the higher the power transmission efficiency. The
ratio smaller than 2:1 assure an acceptable efficiency.
Antenna Gain
Directivity is the ability of an antenna to focus energy in a particular direction when
transmitting, or to receive energy from a particular direction when receiving. If a
wireless link uses fixed locations for both ends, it is possible to use antenna directivity to
concentrate the radiation beam in the wanted direction.
The gain of an antenna is a measure that takes into account the efficiency of the
antenna as well as its directional capabilities. In fact, it is the product of its total
efficiency and its directivity in a certain direction. It is normally regarded as the ratio of
the power gain of the antenna in a given direction to the gain of a lossless isotropic
source as a reference antenna in the same direction. In the specifications, the gain of
the antenna is measured in the direction normal to the plain of the patch.
-
7/30/2019 Huang thesis
21/58
12
Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a continuous
set of frequencies. It is a central concept in signal processing as well as antenna system.
One of the disadvantages of microstrip patch antenna is its low bandwidth, thus the
design goal of the bandwidth is not supposed to be too wide. In some cases, a narrow
bandwidth has its own merit in high interference environment. As a good microstrip
patch antenna, the bandwidth of the antenna should be wider than 1%.
Efficiency
There are two major reasons for the energy loss of the antenna: one is the reflections
because of the mismatch between the transmission line and the antenna, the other is
the conduction and dielectric loss due to Ohms law. Considering these two losses, the
total antenna efficiency can be measured using the voltage reflection coefficient. The
reasonable efficiency of a microstrip patch antenna is at least 70%.
Impedance
The impedance of the antenna is usually designed to be 50Ohms, for its low VSWR and
high energy transmission efficiency.
Nevertheless, in order to improve the noise figure while maintaining a good gain,
conjugate matching is no longer used. Instead, transistor is tested to see which
impedance gives a better noise figure and a high enough gain. Then the antenna is
designed to have such output impedance, and it is connected directly to the transistor.
Compared to the normal method, the matching network used to adjust the antenna
impedance to 50 ohms is omitted.
-
7/30/2019 Huang thesis
22/58
13
3.2 Design Procedure Microstrip Patch Antenna
As shown in Figure 3.1 and 3.2, the microstrip patch antenna presented in this paper
consists of three layers: a 50 mil thick FR4 ( ) substrate, a 15 mil thickconductor, conductivity is 5.88+e07, and a ground plane, which is set to be a perfect
electric conductor (PEC). The RF design of the microstrip patch antenna was done using
the Agilents Advanced Design System (ADS) software.
Figure 3.1: parameters setting of substrate layers in the ADS environment
-
7/30/2019 Huang thesis
23/58
14
Figure 3.2: parameters setting of layout layers in the ADS environment
Applying the equations in chapter 2, we can calculate the size of the patch, and then
attach the two inset feeding parts at both sides of the antenna. Finally, as shown in
Figure 3.3, draw a quarter-wavelength long microstrip line to complete the whole
feeding part.
-
7/30/2019 Huang thesis
24/58
15
Figure 3.3: layout design of microstrip patch antenna
In practice, the most commonly quoted parameter in regards to antennas is S11. S11
represents how much power is reflected from the antenna.
After setting up the size of the antenna, the S parameters become our main concern. As
shown in Figure 3.4, the center frequency of the patch antenna is at 2.451GHz, S11 is -
18.85dB, which is a pretty good result.
However, as can be easily seen in the figure, the bandwidth of the antenna is extremely
narrow. Narrow bandwidth is one of the well-known disadvantages of microstrip patch
antenna; it could be fixed by adding a matching circuit at the output port of the antenna,
which will be mentioned in the next part of this chapter.
-
7/30/2019 Huang thesis
25/58
16
Figure 3.4: S11 of microstrip patch antenna
After some little adjustment is completed, the radiation pattern can be plotted to be
analyzed, as shown in Figure 3.5. The gain at 0 degree is 5.189dB, and the efficiency is
80.931%, both are higher than the specifications.
-
7/30/2019 Huang thesis
26/58
17
Figure 3.5: gain, directivity and efficiency of microstrip patch antenna
The approximate value of the bandwidth can be calculated using this equation:
In this equation, the unit of is GHz and the unit of ismillimeter. Thus the bandwidth of the antenna is approximately 38.42MHz.
The three-dimensional E-plane radiation pattern is shown in Figure 3.6.
For a linearly-polarized antenna, E-plane is the plane containing the electric field vector
and the direction of maximum radiation. The electric field determines the polarization
or orientation of the radio wave.
-
7/30/2019 Huang thesis
27/58
18
Figure 3.6: 3D far field radiation pattern of E
In order to improve the NF while maintaining a good gain, conjugate matching is no
longer used at the input port of the transistor. Instead, transistor is tested to see which
impedance gives a better NF and a high enough gain. Then the antenna is designed to
have such output impedance. And it is connected directly to the transistor. In this case,
the microstrip patch antenna combines the function of a regular antenna and a
matching network.
Normally the value of the resonant input resistance of the antenna is in the range of 100
to 300 ohms. However, the resonant input resistance can be changed by using inset
feeding method. Since there is no formula to calculate the exact output impedance from
the antenna parameters, we have to attach additional microstrip lines to and use the
schematic analysis to adjust the match of the antenna.
Figure 3.7 shows the schematic circuit for the impedance matching, nominal
optimization function is applied to determine the length of the microstrip lines.
-
7/30/2019 Huang thesis
28/58
19
Figure 3.7: schematic circuits for antenna impedance matching
As shown in Figure 3.8, the LineCalc tool is used to determine the width of the
microstrip lines, to make sure that the characteristic impedance is 50 ohms.
Figure 3.8: LineCalc for microstrip line calculation
-
7/30/2019 Huang thesis
29/58
20
And the lengths of TL1 and TL2 in Figure 3.7 are set to be the goal of optimization, and
the parameters of MSub are the same as the antenna.
As shown in Figures 3.9, 3.10 and 3.11, the simulation results have been dramatically
improved in S11, VSWR and impedance parameters, as well as the bandwidth, thus the
Layout design of the microstrip patch antenna was adjusted using the simulation result
of the optimization.
Figure 3.9: S11 of matched microstrip patch antenna
-
7/30/2019 Huang thesis
30/58
21
Figure 3.10: VSWR in 2.45GHz
-
7/30/2019 Huang thesis
31/58
22
Figure 3.11: impedance of matched antenna
-
7/30/2019 Huang thesis
32/58
23
3.3 Result Analysis of Microstrip Patch Antenna
This chapter gives a design procedure of a microstrip patch antenna; the design can be
applied in wireless telecommunications systems. ADS simulations were performed to
predict each parameter to check for compliance against the design specification. The
predictions of the various parameters have been summarized in Table 3.2.
The result indicates that most of the specifications are properly satisfied; especially the
bandwidth and the efficiency are over expectation. However, the impedance of the
antenna is a little higher than 50ohms, which means the signal transmission efficiency
and the power consumption rate may be affected. Thus, when designing the low noise
amplifier, some adjustment has to be made in the impedance part to avoid too much
discontinuity during signal transmission.
Table 3.2 Summary of simulated microstrip patch antenna performance
Parameter Specification The Design
Performance
Unit
Frequency range 2.44-2.46 2.44-2.46 GHz
VSWR 5 5.189 dB
Bandwidth >30 38.42 MHz
Efficiency >75 80.931 %
impedance 50 58 Ohm
-
7/30/2019 Huang thesis
33/58
24
Chapter 4
LNA DESIGN
4.1 LNA Introduction
LNA is an electronic amplifier used to amplify very weak signals. It is usually located very
close to the detection device to reduce losses in the feedline. This active antenna
arrangement is frequently used in microwave systems like GPS, satellite, and radar.
The growing wireless communication market has generated increasing interest in RF
technologies. New technologies are developed to increase higher data rates and
capacity, and to reduce the power dissipation for longer operation time. Low-voltage
and low-power RF circuit design becomes a necessary requirement [5]. A block diagramof a typical AIA receiver front-end is shown in Figure 4.1. The main function of the LNA is
to provide high enough signal gain to overcome the noise of the subsequent stages
while adding the minimum possible noise. Moreover, it should accommodate large
signals without distortion and with specified specific input impedance. A good input
impedance matching is more critical if a pre-select filter precedes the LNA since the
transfer characteristics of many filters are sensitive to the quality of the termination.
The additional requirement is the low power consumption, which is especially important
in portable communications systems [11]. The main characteristic parameters of LNA
are shown as follow:
-
7/30/2019 Huang thesis
34/58
25
Figure 4.1: block diagram of an active integrated antenna amplifier receiver front end
4.1.1 Noise Figure and Noise Temperature
The noise Figure of an amplifier can be defined as:
where, NF is the Noise Figure of the RF device;
are the powers of signal and noise of the input port; are the powers of signal and noise of the output port.Usually, Noise Figure is expressed in dB, which means
Noise temperature is a temperature assigned to a component such that the noise power
delivered by the noisy component to a noiseless matched resistor, which is given by
in watts. Here is the Boltzmann constant, is the noise temperature,and is the noise bandwidth.The noise emitted by the amplifier is expressed by its Noise Temperature. Therelationship between and NF is:
-
7/30/2019 Huang thesis
35/58
26
where is the standard Noise Temperature, and conventionally takes the value as290K.
If several devices are cascaded, the total Noise Figure can be found with Friis Formula:
Where is the noise figure for the n-th device and is the power gain of the n-thdevice. In a well designed receive chain, only the noise figure of the first amplifier
should be significant, thats why the LNA is important in minimizing the noise of the
receiver end of the system.
4.1.2 Gain
There are many different definitions of gain for an amplifier. Normally, for an LNA,
Power Gain refers to the gain measured when the source and load are 50 Ohms.
It is defined as follows:
Where and are the input and output powers respectively.4.1.3 Standing Wave Ratio
In telecommunications, standing wave ratio (SWR) is the ratio of the amplitude of a
partial standing wave at a maximum to the amplitude at an adjacent minimum, in an
electrical transmission line.
The SWR is usually defined as a voltage ratio called the VSWR, for voltage standing wave
ratio. The input matching network is normally designed to approach the minimum noise,
thus it is not the best power matching network, however, the output matching network
is usually designed to get the largest gain and lowest VSWR. That is to say, there exist
mismatch in the input port of the LNA.
-
7/30/2019 Huang thesis
36/58
27
4.1.4 Return Loss
In telecommunications, return loss or reflection loss is the loss of signal power from the
reflection caused at a discontinuity in a transmission line or optical fiber. This
discontinuity can be a mismatch with the terminating load or with a device inserted in
the line. It is also expressed as a ratio in dB.
For a single stage LNA, its noise figure is expressed as:
Where is the minimum noise figure of the transistor, , and is theoptimized return loss when is achieved, the noise impedance of the transistor, andthe input return loss of the transistor, respectively.
4.1.5 Linearity
1 dB compression point and third-order intercept point are two important measures for
weakly nonlinear systems and devices. In the design of LNA, the IP3 of the input LNA is
normally chose to be a little higher, at least 20 dB higher than the input signal, to avoid
much nonlinearity.
4.2 LNA Design Consideration
4.2.1 Impedance matching
Unlike the conventional design, where an antenna and amplifier are separated by astandard 50 Ohms transmission line and interconnects, in the AIA approach, an antenna
is directly attached to the input of amplifier circuit. One of the main challenges in
realizing AIA design is the effective impedance match of antenna element and amplifier
as their impedance mismatch significantly deteriorates the performance of integrated
-
7/30/2019 Huang thesis
37/58
28
devices. Because of the importance of both gain impedance matching, which provides
the maximum gain of AIA device, and noise figure minimum impedance matching, which
minimizes the NF value, an amplifier must be designed according to the impedance
characteristics of antenna element [12].
The condition of perfect gain impedance matching as applied to AIA device is expressed
by where is the normalized input impedanceof an antenna while amplifiers normalized input impedance is given by with being the reflection coefficient of an amplifier at its inputport. These equations simply imply that the input impedance of the LNA is supposed to
be the complex conjugate of the impedance of the antenna.
4.2.2 DC Bias
The bias network determines the amplifier performance over temperature as well as RF
drive. The DC bias condition of the RF transistor is usually established independently of
the RF design. Power efficiency, stability, noise, thermal runway, and ease to use are the
main concerns when selecting a bias configuration [13].
The use of Class-A and Class-AB amplifiers for linear power amplification relies on the
use of a standing bias current, applied to the base (in case of BJT) in order to bias the RF
device into partial or full conduction. This bias current must remain constant, despite
the varying envelope of the input signal to the amplifier, which will cause significant
variations in the collector current required by the devise.
The most common form of biasing in RF circuits is the current mirror. This basic stage is
used everywhere and it acts like a current source. It takes a current as an input and this
current is usually generated, along with all other references, by a circuit called a
bandgap reference generator.
-
7/30/2019 Huang thesis
38/58
29
Figure 4.2: current mirror examples [13]
In the current mirror shown in Figure 4.2, the bandgap reference generator produces
current and forces this current through Q1. Scaling the second transistor allows thecurrent to be multiplied up and used to bias working transistors.
One major drawback to this circuit is that it can inject a lot of noise at the output
due primarily to the gain of the transistor Q1 which acts like an amplifier for
noise.
A capacitor can be used to clean up the noise, and resistors degeneration can beput into the circuit to reduce the gain of the transistor.
With any of mirror topologies, a voltage at the collector of N*Q1 must be
maintained above a minimum level or else the transistor will go into saturation.
Saturation will lead to bad matching and nonlinearity.
-
7/30/2019 Huang thesis
39/58
30
Chapter 5
DESIGN AND ANALYSIS OF LNA
5.1 Low-noise Amplifier Design Specifications
The aim of the research is to design a Low-noise amplifier, which will be connected to
the microstrip patch antenna. Based on the information from Reference [10], the
specifications of the design are shown in Table 5.1.
In this LNA design, the transistor used is an NEC68030 NPN silicon transistor, with typical
noise figure 1.76, gain 10.70, when Vce=6V, Ic=5mA. The amplifier is biased for class A
operation, using current mirror method. The input and output of the transistor are
conjugated matched to the source and load impedance, using microstrip stubs matchingnetworks.
Compared to the specifications in Reference [10], some of the requirements, for
instance, noise figure and gain have been tune down a little. Because the design in this
thesis is only a one stage LNA, but the design in the reference is a two stage LNA with a
cascode stage, which is capable of higher gain while maintaining the same level of noise
figure.
-
7/30/2019 Huang thesis
40/58
31
Table 5.1 The Proposed Design specifications for LNA
Parameter Specification Unit
Frequency 2.4 to 2.5 GHz
Noise Figure 9 dB
Return Loss
-
7/30/2019 Huang thesis
41/58
32
Figure 5.1: schematic circuit of sp-mode scan
In this figure, the NE68030 transistor is sp mode, in which the bias voltage and current
are already set to certain values, which means we can isolate the influence of the DC
bias circuit and focus on the AC performance of the transistor with . The simulation frequency scans from 2.0GHz to 2.8GHz.The reflection coefficient is used in electrical engineering when wave propagation in a
medium containing discontinuities is considered. A reflection coefficient describes
either the amplitude or the intensity of a reflected wave relative to an incident wave.
As shown in Figure 5.2, the input reflection coefficient is close to 50 ohm, while the
output reflection coefficient is not satisfied. In this case, we need to put matching
network in the schematic circuit.
-
7/30/2019 Huang thesis
42/58
33
Figure 5.2: S-parameters of sp-mode
As shown in Figure 5.3, a single-stub matching smart component is set as the input
matching network. The parameters of the substrate are set to be the same as the
microstrip patch antenna in Chapter 3.
-
7/30/2019 Huang thesis
43/58
34
5.3: a single stub matching component is added applied at the input port
The setting of the input matching circuit is shown in Figure 5.4. The center frequency is
2.45GHz, Zin is 50ohms, and Zload is the same as the input impedance of the transistor
which is examined in the previous simulation.
-
7/30/2019 Huang thesis
44/58
35
Figure 5.4: Input matching circuit settings
When the settings are done, the matching network is created automatically, as shown in
Figure 5.5. The simulation result in Figure 5.6 shows that the input reflection coefficient
is even better, the gain and the noise figure and the stability factor are also improved,
but the output reflection coefficient is still not good. Thus an output matching network
is also needed.
-
7/30/2019 Huang thesis
45/58
36
Figure 5.5: Input matching network created by smart component
Figure 5.6: S-parameters when input matching network is added
-
7/30/2019 Huang thesis
46/58
37
Figure 5.7 shows the simulation circuit when the output matching network is added,
which is also a single-stub matching. The width of the microstrip lines are the same as
the lines in the input matching circuit. Nominal optimization tool and goals are set to
optimize the length of the output matching circuit. The goals of the optimization are S-
Parameters, stability factor, and noise figure. After several times of random
optimization, the result is shown in Figure 5.8, in which the output matching is
dramatically improved, the noise figure and stability factor are also improved.
Figure 5.7: schematic circuit when output matching network is added
-
7/30/2019 Huang thesis
47/58
38
Figure 5.8: S-parameters when output matching network is added
5.2.3 DC bias circuit
The bias circuit works by adjusting the gate voltage to maintain a particular value of
drain current. Figure 5.9 shows the ADS schematic simulation of the LNA design with
bias circuit. The sp mode transistor is replaced by a normal pack; an active current
mirror and a current source is setup for biasing the transistor. The bias resistor R1 is
used to isolate the current mirror from the RF input, and the capacitor C4 in the bias
circuit is used to clean up the noise, which is discussed in chapter 4.
-
7/30/2019 Huang thesis
48/58
39
Figure 5.9: bias circuit design schematic
Since the noise figure is not satisfied, and the performance of the S-parameters has
some space to be adjusted to fit the noise matching, a noise circle is applied to find a
better noise matching method.
Unlike the conventional design, where an antenna and amplifier are separated by a
standard 50ohm transmission line and interconnects, in the AIA approach, an antenna is
directly attached to the input of amplifier circuit.
One of the main challenges in realizing AIA design is the effective impedance matching
of antenna element and amplifier as their impedance mismatch significantly
deteriorated the performance of integrated devices.
Because of the importance of both gain impedance matching, which provides the
maximum gain of AIA device, and noise figure minimum impedance matching, which
minimizes the NF value, an amplifier must be designed according to the impedance
characteristics of antenna element.
-
7/30/2019 Huang thesis
49/58
40
Figure 5.10 shows the noise contour in smith chart, which indicates that the ideal noise
figure is around 2dB, which can be achieved by adjusting the impedance of the matching
network.
However, if the noise figure is set to 2 dB, the impedance of the LNA would be too high,
which will severely affect the efficiency and S-parameters. So choosing an impedance of
the LNA bigger than 50 ohms and setting the noise figure to 2.5dB would be a more
reasonable idea.
Figure 5.10: noise circles of LNA
After several times of random optimization, the parameters of the matching network
and DC bias are determined. The simulation results are a compromise between noise
figure, gain, stability, and S-Parameters, which is shown in Figure 5.11 and 5.12.
-
7/30/2019 Huang thesis
50/58
41
Figure 5.11: S-parameters of biased LNA design
Figure 5.12: other parameters of biased LNA design
-
7/30/2019 Huang thesis
51/58
42
5.2.4 Linearity
The 1dB compression point is calculated to examine the linearity of the LNA. If an
amplifier is driven hard enough the output power will begin to roll of resulting in a drop
of gain known as gain compression. The measurement of gain compression is given by
the 1dB gain compression point. This parameter in another measure of the linearity of a
device and is defined as the input power that causes a 1 dB drop in the linear gain due
to device saturation [10]. The compression measurement is shown in Figure 5.13.
As the figure shows, the 1dB compression point is about 1dbm, which is a satisfying
result, indicates that the linearity of this LNA design is acceptable.
Figure 5.13: Linearity parameters of LNA
-
7/30/2019 Huang thesis
52/58
43
5.3 Result Analysis of Low-noise Amplifier Design
This chapter gives a design procedure of a Low-noise Amplifier; which can be connected
with a microstrip patch antenna. ADS simulations have been given to predict the various
circuit parameters of gain, noise figure, power consumption and 1dB compression point,
all summarized in Table 5.2.
The simulation results are close to the specifications. The optimization tool and the
noise contour show that 2.5dB noise figure and 10 dB gain cannot be achieved
simultaneously, thus a compromise has to be made between these two parameters.
Otherwise, a cascode stage amplifier can be added to amplify the signal to get an even
better gain.
Table 5.2 Summary of simulated LNA performance
Parameter Specification Prediction Unit
Frequency 2.4-2.5 2.4-2.5 GHz
Noise Figure 9 9.6 dB
Power consumption
-
7/30/2019 Huang thesis
53/58
44
Chapter 6
COMPLETE AIA DESIGN ANALYSIS
In this chapter, the designs of microstrip patch antenna and low-noise amplifier are
combined together, tested and simulated using Agilent ADS. Figure 6.1 shows the
schematic circuit of the complete AIA circuit, and Figure 6.2 display the layout design of
the proposed AIA. Based on the simulation result shown in Figure 6.3, the bandwidth is
extended to more than 5%, S11 is improved to -36dB, VSWR is less than 1.5dB, and the
input impedance is close to 50Ohms. The overall size of the antenna including the
amplifier circuit is less than 50 , which is much smaller compared to 120, thesize of a normal circular microstrip antenna. Thus the size of the new antenna is less
than 50% of the circular microstrip antenna [16].
Matching of the microstrip patch antenna and the low-noise amplifier does not go quite
well at first. It is probably because the input impedance of the antenna is higher than 50
ohms, which affects the performance of the integration. After another optimization of
the first two stub matching circuits, both the VSWR and voltage reflection coefficient are
dramatically improved. The VSWR at 2.45 GHz drops to 1.16, and S11 at 2.451 GHz is
also decreased to -25 dB. Since the length of the first stub is decreased, the total size of
the AIA in layout design becomes smaller at the same time.
Some of the parameters are not applied in the simulation model, thus there are
differences between simulation result and the actual performance of the AIA. For
example, the inductors should have resistance and Q value, and some parasitic
-
7/30/2019 Huang thesis
54/58
45
capacitance and capacitors have also inductance and resistance, and so on. The values
of those parameters are sometimes told in the datasheets, but not always. When doing
some important and specific simulations, it is necessary to measure the parasitic
elements of the used components.
The simulated noise figure is not good enough, considering that the actual noise figure
will increase when Q value of the inductors is applied. Because of the resistor added in
the bias current circuit to isolate the RF signal, the power consumption is a little higher
than what I expected.
To improve this design, a cascode stage can be added to the LNA. The cascode is a
combination of a common-source amplifier with a common-gate load, which has the
effect of increasing the output impedance, and would also raise the gain as well as
lower the noise figure.
Figure 6.1: schematic circuit of the complete AIA design
-
7/30/2019 Huang thesis
55/58
46
Figure 6.2: Layout design of the AIA
Figure 6.3: simulation result of the complete AIA design
-
7/30/2019 Huang thesis
56/58
47
Chapter 7
CONCLUSION
In this thesis, a design and simulation result of an active integrated antenna is presented.
Compared to the conventional amplifying antenna, the new active integrated antenna
leads to significant advantages such as compactness of the configuration, high power
transmitting efficiency, and low noise. The antenna and the LNA performance match the
specifications properly. However, a better performance can be achieved if a cascode
stage is connected to the LNA. Compared to a single amplifier stage, the cascode stage
may have these characteristics: higher input-output isolation, higher input impedance,
high output impedance, higher gain or higher bandwidth.
It can be seen that the active integrated antenna will be versatile applications in the
growing area of wireless communications. The key requirements for components and
system to be used in wireless communications are compactness, light weight, low cost,
low DC power consumption, high DC and RF conversion efficiency, and high reliability.
The concept of active integrated antenna satisfies the first three requirements and, with
the improving performance of solid state devices, the last three requirements can also
be satisfied [1]. Thus it is possible that the development of active integrated antennas
will bring the wireless communication technology into a new era.
-
7/30/2019 Huang thesis
57/58
48
BIBLIOGRAPHY
[1] Jenshan Lin and Tatsuo Itoh, Active Integrated Antennas, IEEE Transactions on
Microwave Theory and Techniques, Vol.42, NO.12, Dec, 1994, 2186-2194.
[2] Zied haroumi, Lotfi osman, Ali gharsallah, Efficient 2.45 GHz proximity coupled
microstrip patch antenna design including harmonic rejection device formicrowave energy transfer, International Renewable Energy Congress,
November 5-7, 2010.
[3] Constantine A. Balanis,Antenna Theory Analysis and Design, 2nd
ed. John Wiley
& Sons, New York, 1997.
[4] R.R. Garg, P. Bhartia, Inder Bahl, and A. Ittipiboon, Microstrip Antenna Design
Handbook, Artech House, Nov. 2000, 317 -360.
[5] Wan-Rone Liou, Mei-Ling Yeh, Chun-An Tsai, Shun-Hsyung Chang, Design and
Implementation of a Low-voltage 2.4-GHz Cmos RF Receiver Front-end for
Wireless Communication,Journal of marine science and technology, 2005, 170-
175.
[6] Pozar D M and Voda S M, A rigorous analysis of a microstripline fed patch
antennas,IEEE Trans. AntennasPropag. A-35 (12) 13439, 1987.
[7] M I Ali and S Ohshima, Effect of inset feeding on antenna properties in ssuperconducting microstrip antenna, Supercond. Sci. Technol. 18(2005) 1342-
1347.
[8] Lorena I. Basilio, Michael A.Khayat, Jeffery Williams, Stuart A.Long, The
Dependence of the Input Impedance on Feed Position of Probe and Microstrip
-
7/30/2019 Huang thesis
58/58
Line Fed patch Antennas, IEEE Trans. Antennas Propagat, Vol.49, pp.45-47,
Jan. 2001.
[9] M. Ramesh and YIP KB, Design Formula for Inset Fed Microstrip Patch Antenna,
Journal of Microwaves and Optoelectronics, Vol.3, December 2003
[10] J P Silver, Mos Common-source LNA Design Tutorial,
http://www.odyseus.nildram.co.uk/
[11] D.K. Shaeffer, T.H. Lee,A 1.5 V, 1.5G Hz CMOS low noise amplifier,IEEE Journal
of Solid-State Circuits, 35 (2) (1999) 745759.
[12] Andrey S. Andrenko, Yukio Ikeda, Masatoshi Nakayama, Osami Ishida,
Impedance Matching in Active Integrated Antenna Receiver Front End Design,
IEEE Microwave and Guided Wave Letters, Vol. 10, NO. 1, JAN 2000.
[13] Iulian Rosu, Bias Circuits for RF Devices,http://www.qsl.net/va3iul/
[14] Michael Steer, Microwave and RF Design a System Approach, Scitech Publishing,
2010.
[15] http://www.datasheetcatalog.com/datasheets_pdf/N/E/6/8/NE68030-T1.shtml
[16] Rohith K. Raj, Sona O. Kundukulam, C.K.Aanandan, K.Vasudevan, P.Mohanan,
Praveen Kumar, Compact Amplifier Integrated Microstrip Antenna, Microwave
and Optical Technology Letters, Vol.40, No.4, Feb 2004
http://www.qsl.net/va3iul/http://www.qsl.net/va3iul/http://www.qsl.net/va3iul/http://www.datasheetcatalog.com/datasheets_pdf/N/E/6/8/NE68030-T1.shtmlhttp://www.datasheetcatalog.com/datasheets_pdf/N/E/6/8/NE68030-T1.shtmlhttp://www.datasheetcatalog.com/datasheets_pdf/N/E/6/8/NE68030-T1.shtmlhttp://www.qsl.net/va3iul/
top related