function generator

1

A PRESENTATION

ON OPERATIONAL AMPLIFIER

BASED FUNCTION GENERATOR

SUBMITTED TO: SUBMITTED BY:MR. SAURABH KUMAR RAJ SINGHMR. AZHAR SHADAB

2

CONTENTS

INTRODUCTIONSPECIFICATIONSWORKINGSQUARE WAVE GENERATORTRINGULAR WAVE GENERATORSIN WAVE GENERATOROUTPUTS

3

INTRODUCTION A function generator is usually a piece of electronic test

equipment or software used to generate different types of electrical waveforms over a wide range of frequencies.

Some of the most common waveforms produced by the function generator are the sine, square, triangular and saw tooth shapes. These waveforms can be either repetitive or single-shot.

4

SPECIFICATIONS

Produces sine, square, triangular, saw tooth (ramp), and pulse output.

It can generate a wide range of frequencies.

Frequency stability of 0.1 % per hour for analog generators.

AM or FM modulation may be supported.

Output amplitude up to 10V peak-to-peak.

5

WORKING Simple function generators usually generate triangular waveform whose

frequency can be controlled smoothly as well as in steps. 

This triangular wave is used as the basis for all of its other outputs. The triangular wave is generated by repeatedly charging and discharging a capacitor from a constant current source.

This produces a linearly ascending or descending voltage ramp. As the output voltage reaches upper and lower limits, the charging and discharging is reversed using a comparator, producing the linear triangle wave.

By varying the current and the size of the capacitor, different  frequencies may be obtained.

6

 Saw tooth waves can be produced by charging the capacitor slowly, using a current, but using a diode over the current source to discharge quickly - the polarity of the diode changes the polarity of the resulting saw tooth, i.e. slow rise and fast fall, or fast rise and slow fall.

A 50% duty cycle square wave is easily obtained by noting whether the capacitor is being charged or discharged, which is reflected in the current switching comparator output.

Other duty cycles (theoretically from 0% to 100%) can be obtained by using a comparator and the saw tooth or triangle signal.

Most function generators also contain a non-linear diode shaping circuit that can convert the triangle wave into a reasonably accurate sine wave by rounding off the corners of the triangle wave in a process similar to clipping in audio systems.

7

8

SQUARE WAVE GENERATOR

First the inverting terminal (2) is at zero potential and the input at the non-inverting terminal (3) has some potential V1. This occurs due to the power supply of the operational amplifier. The potential difference between the two input terminals is Vi= V1-0 = V1.

9

This ‘+ ve’ voltage drives the output of operational amplifier into ‘+ ve’ saturation voltage (+Vsat).

When the + Vsat is fed back to the inverting terminal (2) through the resistor R, the capacitor C gets charged and the potential of the right side plate of the capacitor gradually rises (or) the V2 value rises.

When V2 becomes slightly more than V1, the input becomes ‘–ve' and immediately this ‘–ve’ voltage drives the output of the operational amplifier in to ‘–ve’ saturation voltage (- Vsat).

Now the capacitor discharges gradually. When V2 becomes less than V1 and (V1 – V2) becomes ‘+ve’ and the output drives to +Vsat. The same process is repeated and the output of the operational amplifier swings between two saturation voltages i.e. between + Vsat and - Vsat. The output Eo of the operational amplifier is square wave.

10

TRIANGULAR WAVE GENERATOR

11

The integrator acts like a storage element that "produces a voltage output which is proportional to the integral of its input voltage with respect to time".

In other words the magnitude of the output signal is determined by the length of time a voltage is present at its input as the current through the feedback loop charges or discharges the capacitor as the required negative feedback occurs through the capacitor.

12

SINE WAVE GENERATOR

Generation of sine wave can be accomplished by employing a positive-feedback loop. It consists of an amplifier and RC or LC frequency selective network.

13

A positive feedback loop is formed by an amplifier with gain A and a frequency-selective network with gain β. In the figure an input signal of Xs is shown but in actual oscillator no signal input is present. The amplifier, however, needs a DC supply for proper operation. The loop gain of this circuit in figure is given by –A(s)β(s).

14

For a sustained stable oscillation, the loop gain should be one; i.e. 1=A(s)β(s) = A(jω0)β(jω0). At the frequency ω0 the phase of the loop gain should be zero and the magnitude of the loop gain should be unity. This is known as Barkhausen criterion. The frequency ω0 should be unique otherwise we wouldn’t have a pure sine wave.

To obtain a sustained oscillation at this frequency, one should set the magnitude of the loop-gain to unity. This can be achieved by selecting

15

OUTPUTS

SQUARE WAVEFORM

16

TRIANGULAR WAVEFORM

17

SINE WAVEFORM

18

THANK YOU