ed iskenderian racing cams - isky cams · this created a new challenge. as the new camshafts were...
Post on 19-Jun-2019
281 Views
Preview:
TRANSCRIPT
ED ISKENDERIAN RACING CAMS
DO IT RIGHT...
...RACE WITHTHE LEGEND
New RADTM Tool Room Part No’s: See Page 40
NEW RED-ZONETM Roller Lifter Part No’s: See Page 16
New Expanded Cam Profile Listings:See Pages 172-179
New EZ-ROLLTM Keyway Roller Lifters: See Page 26
New EZ-ROLLTM Bearing Option: See Page 20
U.S. Patents #8,464,678 and #8,851,038.
"Home of the worlds best roller lifters"
INTRODUCTIONThe name Ed Iskenderian is a legend
among racers worldwide. Ed’s life historyparallels the proverbial success story. He was born in 1921 in the grapevine country of Tulare County, California.His future as a winemaker never
materialized,however, because severalheavy frosts destroyed the vineyards. These conditions forced the Iskenderianfamily to move to Los Angeles.While attending Polytechnic High School
in Los Angeles, Ed’s pet project was buildinga Model T Ford roadster. Ed learned thefundamentals of mechanics by working withthe Model T Fords and later adapted theoverhead conversion by Frontenac (morecommonly known as Fronty), as well as the George Riley head known to the racersin those days as the “multi-flat head.”Experiencing repeated crankshaft failure,
Ed began searching for an engine with astronger lower end. He examined the FordModel A and B and found them to be onlyslightly stronger than the Model T. Turninghis attention toward the later Ford V-8 flathead engine, he found the crank to bemuch more rugged with larger bearings anda counter balanced crankshaft. He installedspecial Maxi “F” type cylinder heads (withoverhead exhaust valves) and slingshot intake manifold.Ed had the combustion chambers in
the heads cast iron filled and he then re-contoured the combustion chambers as advised by his good friend Ed Winfield.The actual compression ratio turned out to be a whopping 13:1, an extremely highratio for the early days of hot rodding.
This was Ed Iskenderian’s first hot rod and it still occupies a corner of his plant today.After graduating, Ed obtained mechanical experience working as an apprentice tool and die maker. This is where Ed
developed the skill and experience of always striving for quality and perfection. His career was interrupted by WWII. Becauseof his interest in speed, Ed decided to try his hand with an even faster vehicle and enlisted in the Army Air Corps. He servedwith the Air Transport Command, repeatedly flying supplies to the islands of the Pacific.After his war time absence, Ed lost no time in getting back to his hot rod and getting it ready for California’s dry lake bed
meets. When rebuilding his V-8, he wanted to obtain a special camshaft. However, the boom had hit hot rodding and therewas a great deal of business for the few racing camshaft manufacturers on the west coast. Their production schedules weretaxed, which resulted in slow delivery. During the five month waiting period for his special camshaft, Ed decided to enter thecam grinding business. He bought a used conventional cylindrical grinder. Drawing on his tool making and mechanical experience, Ed converted it to a universal cam grinding machine. This machine produced camshafts with a noticeable improvement in performance over the conventional racing Ford camshafts. Ed’s cams were the first to produce 1 H.P. per Cu. In. on gasoline in postwar OHV V-8 Dodge Hemi’s and 1.3 H.P. per Cu. In. on gasoline in postwar OHV 283 Chevy V-8’s.Ed saw that racers could benefit from the advancement of higher-technology in racing so he created the first HardFace
Overlay camshafts in the industry and became the first to employ computers in camshaft design. With the computer, Ed created the most advanced cam-profiles of the late 1950s and early 60s like the famous 5-Cycle and Polydyne Profile 505 Magnum’s along with the very first Hydraulic racing camshafts in the industry. Not stopping here, Ed knew that these new camshafts needed equally technologically advanced components -- So, he developed the first High-DensityChilled-Iron lifters for the ever growing Fuel Burning Supercharged Dragster class (now known as Top Fuel Dragsters), the first drop-in self locking roller tappets and the first Anti-Pump-Up hydraulic lifters enabling Hydraulic camshafts to produce higher R.P.M.
ED ISKENDERIAN
This created a new challenge. As the new camshafts were delivering greater lifts and durations for higher R.P.M., the resulting higher lift rates required advanced valve spring designs. Recognizing this, Ed then introduced to the racing industrythe first Vasco Jet 1000 Valve Springs after having pioneered the first valve spring assemblies for racing a decade before.New Cams and Components were not the only thing Ed brought to the young Drag Racing programs. Under a gentlemensagreement, Ed Iskenderian and a young racer from Florida named Don Garlits entered into the first corporate sponsorship ofa race operation. During this time Ed was given the nickname of Isky the “Camfather”.In addition to the numerous racing advancements, Ed also turned his interest to helping the stock/street enthusiasts. He
offered among many other things, the first coordinated cam and assembly kit to take the guess work out of ordering. To helpfine tune racers engines he offered the first “Ultra Rev-Kits” for small block Chevy V-8 roller cams and the first anti-cam walkkit for the Chevy V-8s, along with the first offset cam keys and bushings for adjusting cam timing.In 1963, Ed in collaboration with a few other industry pioneers, created the “Speed Equipment Manufacturers Association”,
now known as the “Speciality Equipment Market Association” or “SEMA”. Ed presided as its first president in 1963 and 1964and led the group through its first crucial years.With the advent of the new small cars and the consumers trend towards economy, Ed turned his efforts to enlarging his
line of economy camshafts and components, creating a camshaft that would deliver economy without robbing performance.This led to the newest and strongest line of street/performance camshafts. The SuperCams for economy/performance and the MegaCams, the maximum in street/performance hydraulic camshafts.Ed, although still overseeing the entire operation, has recently turned the reins over to his sons Ron and Richard who
have continued their father’s traditions. In the last three years, Ron has developed over 100 new cam profiles using a newcomputer design program which he developed to cut the design time by more than 3/4.In collaboration with his brother Richard, they have designed over a dozen new valve spring combinations for oval
track and drag racing (blown alcohol and top fuel classes). Richard is personally present at many major and local tracks, conventions, and seminars to talk with the racers, engine builders and owners in order to keep an eye on the everchangingneeds of a growing industry. In addition, Isky who created the first manufacturers’ cash contingency awards for drag racing inthe 1950s, is involved with major and minor sponsorships as well as a growing support of local tracks to give many racers achance to race in their home towns.One of Eds proudest achievements came in 1985 when he was inducted as a member of Chevrolet’s “Legends of
Performance”, an honorary group of “Men whose visions, skill and perseverance have reshaped the automobile into something more than just transportation. Men who have elevated motorsports and high performance to the levels of prominence they enjoy today,” quoting Chevrolet. Also in the same year, Ed was inducted into the SEMA hall of Fame, theonly Cam Manufacturer to be honored by both organizations.Isky’s present location in Gardena, California consists of a four-building complex of over 75,000 square feet on property a
full city block long. Isky employs over 100 specialists, including engineers and technical advisers to assist the thousands ofIsky dealers throughout the world and the hundreds of thousands of Isky customers. To answer the many questions that comein daily from enthusiasts of circle track, off road, drag racing, Bonneville, truck and tractor pullers, monster trucks, street, andstock cars and boats, Ed has written many helpful pamphlets for technical advice on cam installations including installing, valve timing, cam degreeing, dyno tuning, preventing roller cam walk and top tuning tips. Most of these are included in this catalog.As the world’s largest racing, performance, and economy cam manufacturer, Isky maintains a dynamometer testing
program for constant improvement of camshaft and valve train design. These tests are conducted daily in Isky’s new enlargeddyno facility. To propertly evaluate and prove the efficiency of Isky racing cams and valve train components, Isky maintains acontinuous engine testing program. Still another dynamometer is used exclusively for the purpose of testing the endurance ofracing valve gear components in today’s OHV engines. The final phase of testing is accomplished when the newly dynotested cams and components are coordinated with the best stock and performance equipment into racing cars and boats aswell as performance and stock street machines. The testing is completed under actual racing and street conditions that our customers may encounter. This assures the consumer of accuracy and quality control unparalleled in the industry. The results ofthese tests are available to all hot rodders, racers, and engine builders in the form ofhorsepower charts, plus information on carburetion, jetting, ignition, timing, and exhausts. These are just a few of the many ways Isky’s research is shared with the racing enthusiasts.At Isky Racing Cams you can always count
on helpful, courteous service, the highest quality materials in all our products, the newest advancements and the finest workmanship available.
ED ISKENDERIAN’S T ROADSTER
4
VALVE TRAIN WEAPONS (continued)Valve Spring Locaters . . . . . . . . . . . . . . . . . . . . . . . . . . .52Valve Stem Oil Seals . . . . . . . . . . . . . . . . . . . . . . . . . . .52Valve Timing Booklet . . . . . . . . . . . . . . . . . . . . . . . . . . .63
CAMS & KITSMega-Cams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70-71Super-Cams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68-69Cam & Lifter Kits (Hydraulic) . . . . . . . . . . . . . . . . . . . . . .67
AMERICAN MOTORSV8 1966-Up 290-401 Cu. In. . . . . . . . . . . . . . . . . . . . . . .726 Cyl. 1964-Up 199-258 Cu. In. . . . . . . . . . . . . . . . . . . .74
BUICKV8 215” Alum. & 300-340 Iron . . . . . . . . . . . . . . . . . . . . .74V8 1968-Up 350 Cu. In. . . . . . . . . . . . . . . . . . . . . . . . . .76V6 1962-71 198-225 Cu. In. . . . . . . . . . . . . . . . . . . . . . .76V6 1975-77 231 Odd-Fire . . . . . . . . . . . . . . . . . . . . . . . .78V6 1978-Up 196-231-252 Even Fire . . . . . . . . . . . . . . . .78V8 1967-Up 400-455 Cu. In. . . . . . . . . . . . . . . . . . . . . . .80
CHEVROLETCorvair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .804 Cyl. Chevy II 153 Cu. In. . . . . . . . . . . . . . . . . . . . . . . .82409 Cu. In. V-8 (1958-65) . . . . . . . . . . . . . . . . . . . . . . . .826 Cyl. Chevy II 194-230-250 Cu. In. . . . . . . . . . . . . . . . .846 Cyl. 1963-Up 292” Truck . . . . . . . . . . . . . . . . . . . . . . .86V6 90O & 60O Engines . . . . . . . . . . . . . . . . . . . . . . . .86-89V8 265-400 Cu. In. Engines (Vacuum Rule) . . . . . . . . . .66V8 265-400 Cu. In. Engines . . . . . . . . . . . . . . . . . . . . . .90V8 396-454 Cu. In. Engines . . . . . . . . . . . . . . . . . . . . .110
CHRYSLERV8 “A” 1964-Up 273-360 Cu. In. . . . . . . . . . . . . . . . . . .120V8 “B” 1958-Up 350-383-440 Cu. In. . . . . . . . . . . . . . .124V8 426 St. Hemi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128V8 1957-58 392 Cu. In. Hemi . . . . . . . . . . . . . . . . . . . .128
FORD4 Cyl. 2000cc Pinto-Capri . . . . . . . . . . . . . . . . . . . . . . .1304 Cyl. 2300cc Mustang-Pinto 1974-87 . . . . . . . . . . . . .130V6 2600 & 2800cc Engines . . . . . . . . . . . . . . . . . . . . . .1326 Cyl. 144-200 Cu. In. Engines . . . . . . . . . . . . . . . . . . .132V6 3.8L 232 Cu. In. 1982-Up . . . . . . . . . . . . . . . . . . . .134V8 272-312 Cu. In. Engines (Y-Block) . . . . . . . . . . . . .1346 Cyl. 1965-Up 240-300 Cu. In. . . . . . . . . . . . . . . . . . .1366 Cyl. 250 Cu. In. Engines . . . . . . . . . . . . . . . . . . . . . .136Clarification of Ford - V8 Engines . . . . . . . . . . . . . . . . .138
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Sales Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Isky Engineering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
VALVE TRAIN WEAPONSAnti-Cam-Walk Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57CC Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62Cam Degreeing Booklet . . . . . . . . . . . . . . . . . . . . . . . . .63Cam Sprocket Lock Plate . . . . . . . . . . . . . . . . . . . . . . . .55Cam Timing Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58-59Chevy Chain Drive Sprockets . . . . . . . . . . . . . . . . . . . . .56Degree Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62Distributor Gears (Aluminum Bronze) . . . . . . . . . . . . . . .56Groove-O-Matic (O-Ring Tool) . . . . . . . . . . . . . . . . . . . .61Guide Plates (Adjustable) . . . . . . . . . . . . . . . . . . . . . . . .55Height Mike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Hole Saws (Counter-Boring) . . . . . . . . . . . . . . . . . . . . . .60Lash Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Lifter Bore Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Lifters, Solid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Lifters, Hydraulic “Anti Pump-Up” . . . . . . . . . . . . . . . . . .10Lifters, Hydraulic Rollers . . . . . . . . . . . . . . . . . . . . . .11-14Lifters, Mech Rollers . . . . . . . . . . . . . . . . . . . . . . . . .15-25Micro Shim Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Offset Cam Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . .56Piston Notching Cutters . . . . . . . . . . . . . . . . . . . . . . . . .60Poly Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Pushrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44-48Pushrods (Adjustable Check Type) . . . . . . . . . . . . . . . .58Ratio Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63Retainers (Steel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42Retainers (Titanium) . . . . . . . . . . . . . . . . . . . . . . . . . . . .43Rev-Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54Rev-Lube/Oil Supplement . . . . . . . . . . . . . . . . . . . . .64-65Rocker Arms (Aluminum) . . . . . . . . . . . . . . . . . . . . . . . .49Rocker Arms (Stamped Steel “Long Slot”) . . . . . . . . . . .51Rocker Arm Pivot Balls . . . . . . . . . . . . . . . . . . . . . . . . . .50Rocker Studs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Shims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Soft Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59Three Bolt Coversion Kit (Chrysler) . . . . . . . . . . . . . . . .56Timing Chain/Gear Sets . . . . . . . . . . . . . . . . . . . . . . .56-57Thrust Bearings (Roller) . . . . . . . . . . . . . . . . . . . . . . . . .55Valve Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53Valve Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-41Valve Spring Cups . . . . . . . . . . . . . . . . . . . . . . . . . . .51-52Valve Spring Kits (Chevy LS-1 V8) . . . . . . . . . . . . . . . . .27Valve Spring Kits (Honda 4 Cyl) “Fast Zone” . . . . . . .33-36
TABLE OF CONTENTS
5
MARINE APPLICATIONS . . . . . . . . . . . . . . . . . . .168-171
OLDSMOBILEV8 F-85 1961-63 215 Alum. Engines . . . . . . . . . . . . . .158V8 1964-Up 330-455 Cu. In. . . . . . . . . . . . . . . . . . . . . .160
PONTIACV8 1955-Up 265-455 Cu. In. . . . . . . . . . . . . . . . . . . . . .1624 Cyl. 151” Iron Duke . . . . . . . . . . . . . . . . . . . . . . . . . .166
ISKY APPAREL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
IMPORT CAR SECTION(Condensed Version) . . . . . . . . . . . . . . . . . . . . . .181-185
CAM RECOMMENDATION QUESTIONNAIRE . . . . . .180
FORD (continued)V8 1932-53 Flathead . . . . . . . . . . . . . . . . . . . . . . . . . . .138V8 351 Cleveland & 351 “M” . . . . . . . . . . . . . . . . . . . . .140V8 Boss 302 Cu. In. . . . . . . . . . . . . . . . . . . . . . . . . . . .144V8 221-260-289-302 . . . . . . . . . . . . . . . . . . . . . . . . . . .146V8 351 Windsor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150V8 302 H.O. 1985-Up Hyd. Roller Cams . . . . . . . . . . .150V8 352-360-361-390-406-427-428 . . . . . . . . . . . . . . . .152V8 1968-Up 370-429-460 Cu. In. . . . . . . . . . . . . . . . . .154
INTERNATIONALV8 304-345-392 Cu. In. . . . . . . . . . . . . . . . . . . . . . . . . .158
LOBE SPECIFICATION CHART . . . . . . . . . . . . .172-179
For the most up to date information on new products, visit us at our website: www.iskycams.com
ED ISKENDERIAN RACING CAMS16020 S. BROADWAY GARDENA, CALIFORNIA 90247-9990
(310) 217-9232 FAX (310) 515-5730
Reproduction in whole or in part of any content of this catalog is forbidden without written permission from ED ISKENDERIAN RACING CAMS. Entire contents copyright 2016 by Ed Iskenderian Racing Cams.
All rights reserved. Printed in U.S.A.
The camshafts listed in this catalog are not legal for sale or use on pollution controlled motor vehicles, operated on highways or roads.
TABLE OF CONTENTS (CONTINUED)
THE FOLLOWING TECHNICAL DATA IS NOW AVAILABLE ONLINE @ iskycams.comCam Degreeing is Simple • How to Install A Camshaft • How To Prevent Roller Cam Walk
Valve Open Values (VOTC) • Tech Tips 2000TM • And Our Complete Import Car Section
6
ISKENDERIAN SALES POLICYRETAIL SALES:Whenever possible, merchandisemust be purchased through an authorized IskenderianDealer. The factory will only sell directly to you if there is no authorized dealer in your area. If you do notknow the name and address of your nearest Iskenderian Dealer, write or call the factory for this information.
HOW TO ORDER:When ordering from IskenderianRacing Cams, be sure to clarify your order - state partnumber and description of merchandise. Print your fullname, street address, city, state and zip code. Alsospecify shipping instructions.
SHIPPING: Most orders are processed and shippedwithin 24 hours after receipt of order by most economical method of transportation unless otherwisespecified - i.e., United Parcel, Air Parcel Post, AirFreight or truck. A 50% deposit in the form of a PostalMoney Order, cashier's check or certified check is required with all C.O.D. shipments; however, you cansave the C.O.D. charges by prepaying the full amount.If for any reason a shipment is refused, customer willbe billed for freight charges both ways.
BACK ORDERS: If for any reason there is a delay infilling your order, either a postcard notice will be sent toyou or item(s) will be indicated as back ordered (B.O.)on your invoice.
CUSTOM MADE PARTS:Whenever possible, Ed Iskenderian Racing Cams will manufacture specialparts such as a special length pushrod or related itemsnot shown in this catalog. Payment in full, in advance is required on all such orders before we can proceedwith manufacture. No refunds will be made in the eventof cancellation.
RETURN OF MERCHANDISE: No merchandise may be returned for any reason unless prior written permission has been obtained from Ed IskenderianRacing Cams. All shipments approved for return must be shipped prepaid and insured, and must be accompanied by the original invoice or date of invoice.A 15% service charge will be deducted on all returnedmerchandise, except in case of factory error.
FOREIGN SHIPMENTS: All foreign shipments, including all freight charges, must be paid in full, in advance, in American money. Prices shown do not include any import duty, insurance or port fees. Iskenderian will provide a complete proforma invoice, including all charges, so that payment can be arranged.
RIGHTS RESERVED: Ed Iskenderian Racing Cams reserves the right to make changes in design, materials and specifications, or to make productchanges without incurring Iiability or obligation with respect to similar products previously manufactured.
PRINTING ERRORS: Although every effort has been made to proofread all copy prior to printing, we do not accept responsibility for any typographical errors either in prices or content.
TWO YEAR LIMITED WARRANTY
HYDRAULIC SERIES (SUPERCAM, H.L. AND MEGACAM)HI-REV SERIES (STREET & STRIP SOLID LIFTERS)
All Hydraulic Series and Hi Rev Series Camshafts are warranted by Ed Iskenderian Racing Cams against excessive lobe wear for TWO YEARSfrom date of purchase. This warranty is valid ONLY if a complete Iskenderian Assembly Kit has been installed with -- and at the same time of the camshaft installation, and if the installation instructions arefollowed according to those supplied with Cam & Kit.
Ed Iskenderian Racing Cams neither assumes nor authorizes any person to assume for it any other obligation or liability in connection with the sale of ourproducts. Should excessive lobe wear require replacement, return the camshaftand lifters freight prepaid and insured directly to the lskenderian factory. Therewill be a minimum charge of $95.00 for replacement of Hydraulic or SolidCamshaft and lifters. The replacement camshaft is covered for time remainingunder original warranty.
Customer agrees that Ed lskenderian Racing Cams is not reponsible for anylabor, installation charges, damaged and/or replaced parts. Camshaft and/orAssembly Kit parts will be returned to you freight collect. This Warranty is nottransferable and its benefits apply only to the original purchaser.
ONE YEAR LIMITED WARRANTY
ROLLER SERIES
ALL ROLLER SERIES camshafts are Warranted by Ed Iskenderian RacingCams against excessive lobe wear for ONE YEAR from date of purchase. This Warranty is valid ONLY if a complete Iskenderian Assembly Kit hasbeen installed with --and at the same time of the camshaft installation andif installation instructions are followed according to those supplied withCam and Kit.
Ed Iskenderian Racing Cams neither assumes nor authorizes any person to assume for it any other obligation or liability in connection with the sale of ourproducts. Should excessive lobe wear require replacement, return the camshaftfreight prepaid and insured directly to the Iskenderian factory. Also return all the tappets for inspection and/or repair.
There will be a minimum charge of $150.00 for Roller Cams.
All replacement camshafts are covered for time remaining under Original Warranty.
Customer agrees that Ed Iskenderian Racing Cams is not responsible for anylabor, installation charges, damaged and/or replaced parts. Camshaft and/orAssembly Kit parts will be returned to you freight collect. This Warranty is nottransferable and its benefits apply only to the original purchaser.
7
If you’re an engine builder who’s not
satisfied with whatever cam-grinder’s
product you may be using, please give us
a call regarding your cam profile needs or
any other questions you may have on the
subject. We’d enjoy hearing from you and
hopefully we can help with your concerns.
Real cam help from real cam experts!!
We are pleased to announce the recent expansion
of our facilities for the rapid-prototyping of new cam
profile design and manufacturing. Now on line and
running is our new state-of-the-art ProCamTM
cam-design program (incorporating “neural-
optimization” technology) and our specially
equipped (1 micron) precision CNC master cam
generator. We are also currently in the process of
upgrading and servicing every one of our precision
Norton, Cincinnati and Landis cam grinding
machines in preparation for the implementation
of our new Accu-CamTM precision profile
measurement and accuracy standards.
Moderate Tooling & Design Costs May Apply. (Available upon request)�
Cam-Profile Headquarters, U.S.A.TM!Attention: Engine Builders/Valve-Train Designers
Custom MasterCam-Profile ServiceNEW!
�
ISKY ENGINEERING
8
The strategically aggressive nature of new cam lobe profiles now under development at Isky
utilizing our exclusive Profile Expansion TechnologyTM, has led to the implementation of new
higher standards for cam profile accuracy and
measurement - Accu-CamTM standards will
ensure that these new state-of-the-art cam
profiles will perform as designed - expanded to
maximize area under the lift curve! This means
that for a given cam lobe lift and duration at
.050”, these new profiles will be longer in
duration or “fatter” at the higher lift check
points (.200”, .300”, etc.) to maximize engine
breathing potential like never before!
Accu-CamTM: Precision Profile Measurement
and Accuracy Standards
The next generation of cam profile designs!
Many new cam lobe profiles utilizing OUR
exclusive Profile Expansion TechnologyTM
are currently available with more on the
way! See lobe specification chart pages
173, 174, 177 & 179. These lobe designs are
the most aggressive cam profiles ever cre-
ated and generated by ISKY. Significant
increases in cam-profile envelope (the area
under the valve lift curve) and engine
breathing mean that without sacrificing low
& mid range torque, as engine RPM
increases there will be more horsepower
available for you! Watch for new profile release dates by visiting our website at
www.iskycams.com.
Specially Equipped1 Micron Precision CNC Master -
Cam Generator
ISKY ENGINEERING
RESEARCH & DEVELOPMENT...SPINTRON ENDURANCE TESTINGRESEARCH & DEVELOPMENT...SPINTRON ENDURANCE TESTING
The demands of Endurance Racing today are such that every manufacturer of critical engine components,(not their customers), should be testing them on a regular basis to guard against the possibility, however remote, of catastrophic failure. This point was brought home recently when a well-known east coast valvemanufacturer initiated a massive recall of defective heavy-duty stainless steel valves, after their stemsbegan "snapping off" at the keeper groove. The manufacturer's reputation, already suffering from prior embarassments concerning connecting rod failures,was eroded even further over this unfortunate incident.The lesson to be learned here is that this could have all been avoided had this manufacturer of engine components considered testing to be as important a priority as their advertising campaigns.
We at Isky Racing Cams do recognize the absolute neccesity to regularly test critical engine componentssuch as our Endurance Valve Springs and Roller Lifters. That's why we created the most rigorous realworld endurance test ever established, the grueling Spintron® 1,000 Racing Mile Endurance Test Standard™. The first and only one of its kind in the industry, it's a test with a "Zero" Failure Tolerance, because its either pass or fail for our Racing Valve Springs & Roller Lifters-there is no gray area in between! If they don't measure up,we won't sell them-period! We have to,because we know you're depending on the lskenderian family name to deliver the absolute maximum endurance possible in all of our valve train components. Your peace of mind and continued customer loyalty are of primary importanceto us and you may rest assured we will never "cut corners" in our efforts to bring you the World's Finest Endurance Racing Valve Springs and Roller Lifters. Our reputation rides with every set!
10
Quiet Power HydraulicsIsky has available premium-quality stock replacement hydraulic valve lifters. They are ideal for installation with our famous SUPERCAM series of economy-performance camshafts as well as with any other application where a drop-in stock replacement hydraulic lifter is required.
Anti-Pump-Up HydraulicsAlthough the Isky patented SUPERLIFTER outwardly appears similar to a standard hydraulictappet, there is a world of difference in the function of the internal mechanism and design.SUPERLIFTERS allow you to use a more radical camshaft without loss of compression andhorsepower from valves being held off their seats, and because SUPERLIFTERS do notbleed down completely, they are far more durable than any others on the market.Set of 16 SUPERLIFTERS
Part No. Description202-HY For all Chevrolet and Pontiac V-8 Engines Plus 1968 & later Olds V-8 (.842” dia.)
Special Oiling Solid LiftersAs cam profiles become more aggressive to meet the demands of today’s sophisticated Solid LifterOval Track Applications, increasing oil delivery to the cam lobe-face is critical; especially whenhigher valve spring pressures are employed. Isky now has special oiling solid lifters available,based around our popular 202-H Chevy and 382-H Ford designs. A .024” oil hole is EDM’d throughthe cam-face of the lifter, into the pressurized main oil passage of the body. The result is increasedoil delivery at all times to the cam lobe-face area with extended cam lobe/lifter life.
Part No. ApplicationSO 202H Small & Big Block Chevy V-8SO 382H Small Block Ford V-8
RACING LIFTERS
Hardenable Iron SolidsIsky Hardenable Iron Solid Lifters are the ultimate in dependability and performance when used in conjunction with Isky Hi-Rev Series solid lifter cams. Engineered with the stress of Hi-Speed competition in mind, they are also excellent as Hi-Performance replacement for stock lifters when overhauliing an engine or replacing the camshaft. Stronger by design yet lighter in weight than the stock components they replace, Isky hardenable iron solid lifters are an absolute necessity for today’s sophisticated racing engines. (Set of 16)
Part No. Description202-H For all Chevrolet and Pontiac V-8 Engines3102-H All Chrysler Products382-H For all Ford V-8 Engines
Part No. Description222-HY All Chevrolet, V-8 Engines *Chevy V-6 and 230-250 in-line 6 cyl.392-HY Ford V-8 332-352-360-361-390-391-427-428 cu. in. Lincoln V-8 430-462 cu. in. Ford 6 Cyl. 144-170-200-250 cu. in.432-HY Ford V-8 221-260-289-302 cu. in. Ford V-8 351-400 Windsor & Cleveland Ford V-8 370-429-460 *Ford 6 Cyl. 240-300 cu. in.3912-HY Chrysler “B” engine 383-440 cu. in. V-83912-A-HY Chrysler “A” engine 273-318-340-360 cu. in. V-8692-HY Olds. V-8, 1968 & later .842” dia. Pontiac V-8
11
theHPx TM SERIES (Hydraulic Performance Xtreme)Featuring “Best on the Planet” Super-Precision Johnson/SEC® Quality!
NEW!
ABSOLUTE
100%MADE IN THE
U.S.A.GUARANTEE
HPxTM NEEDLE BEARING HPxTM EZ-ROLLTM NEEDLE FREE!
The World’s Finest
Hydraulic Roller Lifters!
SILVER GOLDPERFORMANCE LEVEL
Features:
� �� �� �� �
����
PDQ Hi-Flow ValvingTM
Ultra Super Precision Mfg.
Hear No “Tick”TM / Johnson® Quality
Anti-Flex DefenseTM
Anti-Lock EZ-RollTM Bearings
The Big Foot EffectTM
Triple Rolling ImmunityTM
Patented Vortex-WaveTM
{
Sta
nd
ard
HP
xT
MP
acka
ge
{EZ-Roll
TM
Up
grad
e
12
HPx TM SERIES HYDRAULIC ROLLER LIFTERS FEATURE:
Up
gra
de
feat
ure
s ex
clu
sive
to H
Px
TM
EZ
-RO
LL
TM
GO
LD
Lev
el P
erfo
rman
ce
PATENTED VORTEx-WAVETM
High-efficiency, exterior port, hydro-dynamic oil delivery to roller bearings out performs any othersystem! U.S. Patents #8,464678 and #8,851,038.
THE BIG FOOT EFFECTTM
Expands your Load-DistributionFootprintTM by over 350% comparedto needles! Yes, 350%!
ANTI-LOCK EZ-ROLLTM
BEARINGS
Proprietary Epsilon-ZxTM Solid BearingRaceways incorporate the latest advances in molecular science research and keep you rolling longer - up to 5 times longer than needles!
TRIPLE ROLLING IMMUNITYTM
Roll up to 5 times longer than needles with worldclass protection that shields against: 1. Progressiveneedle bearing friction due to needle-erosion. 2.Catastrophic failure due to needle-bearing overload.3. Bearing seizure due to oil restriction - and no worries about “Brinneling” needles and bearingraces due to valve float!
ANTI-FLEX DEFENSETM
No slip fit axles retained by ring-clips orfalling pins here! Instead, our compressionfitted axles unify the body, legs and axle for a giant leap forward in structural integrity - far superior to any other design!
HEAR NO TICKTM QUIET RUNNING
HPxTM Lifters are simply better because virtual “Zero Taper” manufacturing means no“fake-sizing” issues, where loosely fitting “noisy”lifters leak down too quickly or stick at bottom of travel range causing engine valves to seat at high velocity!
JOHNSON® LIFTERS is a REAL ISO-9001 certifiedhydraulic roller lifter manufacturing facility, consistentlyproducing lifters of unparalleled quality and precision!
P.D.Q. “HI-FLOW” VALVINGTM
PDQ valves seal better and feature quickerresponse time for higher RPM capabilityeven with more “aggressive” (radical) cam-profiles and higher valve spring loading!
ULTRA SUPER-PRECISE
Bodies and pistons are electronically sized,matched and fitted to clearances less than onemicron (plus or minus 30 millionths) of an inchfor consistently quiet, dependable operation!
All
HP
xT
MS
erie
s R
olle
r-L
ifte
rs F
eatu
re:
(Bo
th S
ILV
ER
& G
OL
D L
evel
s)
*EZ-ROLLTM Lifters are protected by U.S. Patents #8,464,678 and #8,851,038.
13
ISKY has partnered with Johnson® Lifters of Taylor, Michigan (the premier Hydraulic-Roller Lifter manufacturer in the country) to offer the “Best on the Planet” HPxTM Series. The absolute Highest Quality, Hi-Performance Hydraulic Rollers
available today for the following engine applications.
PART NO. APPLICATION PUSHROD MAX SPRING/LOADS RPMSEAT/OPEN LIMIT
2076-HYRT LS-1 Chevy V8 203-HG-180” 185/535# 7500 RPM
2077-HYRT Small Block 203-HG-.460” 185/535# 7500 RPMChevy V8
3977-HYRT Big Block 203-96-.500” 185/535# 7500 RPMChevy V8
2477-HYRT 409 Chevy V8 8.350” int / 8.700” ex 185/535# 7500 RPM
3177-HYRT Big Block 429-460 203-HG Plus .300” 185/535# 7500 RPMFord V8
3877-HYRT Small Block 289-302 203-HG Minus .100” 185/535# 7500 RPM351 ford V8
SUPER PRECISION GROUND
(BODIES AND PISTONS)• Ultra Super Precision ground and electronicallysized bodies and pistons are match-fitted towithin millionths of an inch!
• Manufactured in the country’s premier hydraulic Roller Lifter manufacturing facility(ISO-9001 certified)
• Strictly controlled leak down rates for dependably quiet operation!
ZERO TAPER MANUFACTURING!• No “fake” sizing issues where lifters leak down and stick at bottom of travel range likeother brands when put to the test.
QUICK ACTING/FAST RETURN P.D.Q. HI-FLOW VALVINGTM
• PDQ Hi-FlowTM piston valves respond quickerand simply perform better when modern, accelerated ramp cam profiles are pushed tohigher RPM levels!
HPx TM
SILVER SERIESNeedle-Bearing Hydraulic Rollers!
ABSOLUTE
100%MADE IN THE
U.S.A.
GUARANTEE
GREAT FOR:
•Higher RPM
•Aggressive
Cams
•Stiffer Sprin
gs
14
PART NO. APPLICATION PUSHROD MAX SPRING/LOADS RPMSEAT/OPEN LIMIT
2075-HYRT Small Block Chevy V8 203-HG -.460” (7.320) 185/535# 7500 RPM
2078-HYRT LS-1 Chevy V8 203-HG -.180” (7.600) 185/535# 7500 RPM
3975-HYRT Big Block Chevy V8 203-96 Minus .500” 185/535# 7500 RPM
3175-HYRT Big Block 429/460 203-HG Plus .300” 185/535# 7500 RPMFord V8 (8.100)
3875-HYRT Small Block 289/302 203-HG Minus .100” 185/535” 7500 RPM351 Ford V8 (7.700)
HPx TM
ISKY has partnered with Johnson® Lifters of Taylor, Michigan (the premier Hydraulic-Roller Lifter manufacturer in the country) to offer the “Best on the Planet” HPxTM Series. The absolute Highest Quality, Hi-Performance Hydraulic Rollers available today for the following engine applications.
STOMP-OUT NEEDLE OVERLOADWITH
THE BIGFOOT EFFECTTM
EZ-ROLL HYDROTM AND EZ-RIDERSTM
expand your load distribution footprint by over 350%!
PART NO. APPLICATION DESCRIPTION SPRING PRESSURES
100EZR Evolution Standard Leak Down Body up to 160# seat
200EZR Evolution Slow Leak Down Body over 160# seat
300EZR Twin Cam Slow Leak Down Body over 160# seat
GOLD SERIES UPGRADENeedle-Free Hydraulic Rollers!
EZ-RIDERSTM Hydraulic Rollers for Harley Motorcycles!
ABSOLUTE 100% MADE IN THE U.S.A. GUARANTEE!
HPx TM EZ-ROLL HYDROTM / The World’ Best Hyd. Rollers!
15
Endurance PlusTM ROLLER LIFTERS from ISKY!
The DurathonTM Series was developed utilizing the latest advances in precision CNCMachine Cell Technology, focusing on the most popular (Highest Volume) applications. DurathonTM Lifters feature a High Quality, toughalloy body and roller bearing assembly and come standard with “Captive” (Permanently Attached) Guide Bars. All Lifters are precision ground “True-Round” .842” Diameter. DurathonTM Roller Lifters are absolutely 100% Made In The U.S.A. and are competitivelypriced to go head to head with those lower cost foreign made lifters.
DurathonTM Roller Lifters are compatible with All Isky Tool RoomTM Valve Springs and recommended for applications where up to 700 lbs. Maximum Valve Open Spring force is employed.
Get Serious with New DurathonTM Roller Lifters from ISKY!(The ABSOLUTE BEST VALUE IN RACING TODAY)
APPLICATION PART NO. PUSHROD SEAT LOCATION
Small Block Chevy V-8 362-RHM Centerline (Fits both Standard & Raised Lifter Bosses)
Big Block Chevy V-8 366-RHM Centerline (Fits both Standard & Raised Lifter Bosses)
Ford 289-302 & 351-W V-8 3862-RH Centerline
We are now offering a “Captive” (permanently linked) tie-bar for the most Severe Roller Lifter applications. This option isnow available for both Endurance Plus & Red Zone lifters. It is a standard feature on all .904 dia. Chrysler and Chevy .937dia. Red Zone lifters. As with all Isky tie bars, they are specially heat treated to avoid wear and insure against failures.Applications now available
*Small & Big Block Chevy V-8 - *Chrysler V-8; “B” & Hemi*Ford Small Block (289-302); 351 Windsor and Cleveland V-8*Ford 429/460 V-8
Note: There is an additional premum of $25.00 for this option. Add “CPT” to the part number when ordering.
Replacement Guide Bar Sets:Application Part No. Description **Length (see below)Chevy 90 Deg. V-6 GB-100 Set of (6) pcs. (2) 1.355” (4) 1.240”Chevy Small Block V-8 GB-200 Set of (8) pcs. 1.240”Chevy Big Block V-8 GB-454 Set of (8) pcs. 1.500” Std BlockChevy Big Block V-8 GB-502 Set of (8) pcs. 1.500” Bow Tie BlockChrysler V-8 (All) GB-1600 Set of (8) pcs. 1.465”Ford 302-351 c.i. V-8 GB-380 Set of (8) pcs 1.410”Ford 429-460 V-8 GB-310 Set of (8) pcs. 1.750”Pontiac 4-Cyl. 151 c.i. GB-951 Set of (4) pcs. 1.580”Pontiac V-8 GB-900 Set of (8) pcs. 1.465”
* - 180” OFFSET TAPPET INFORMATION
EXCENTERLINE
INTRIGHT
OFFSET
INTLEFT
OFFSET
**Guide BarLength dimension:
A A B C C C
Small Block V-8 (Aluminum Top)Offset Tappet Information
TOP .150VIEW RIGHT OFFSET
PART NO.1271-LORS150
.150 TOPLEFT VIEWOFFSET
WHEN ORDERING INDIVIDUAL PIECES USE PART # 1271-LOLS150
“Captive” Tie Bar option for ISKY Mechanical Roller Lifters
B C NEW!
RED ZONETM Roller Lifters feature the new MarathonTM Roller Bearing—the bearing that keeps on rolling longer! MarathonTM Bearings utilize a larger diameter pin and a shock absorbing thicker outer race for higher fracture toughness! The resulting increased cross sectional area helps prevent prematurebearing failures even under the sustained RPM red line abuse of professional endurance raising. In drag racing, MarathonTM Bearings withstand higher (up to1/2 ton) spring loads, delivering over twice the number of runs between rebuilds!
Exclusive Full Spectrum 3 Point Oiling Systemfeatures continuous dual action pressurized lubricationat all times to the roller bearings and an extra shot of oilover the nose of the cam where loads are greatest (U.S.
Patent in process). Helps preventpremature needle-roller wear
Test Proven RED ZONETM Safe!MarathonTM Bearings routinely log back to back 1,000 racing mileendurance runs via the most rigorous real world test standard ever created, Spintron Test II. It’s a no holds barred run as high as 9000RPM, where race ending competitive abuse is continuously revisited!
Smootherfinishalloy steelbody repelsscuffing.Fullyrebuildable!
ED ISKENDERIAN RACING CAMS • 16020 S. Broadway, Gardena, California 90247-9990(310) 217-9232 FAX (310) 515-5730 www.iskycams.com
17
Red ZoneTM MAXIMUM ENDURANCE ROLLER LIFTERS
BODY BEARINGAPPLICATION PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 272-RH .842” .750” STEEL “B” 203-HG 7.781” 210-LRKSMALL BLOCK (Centerline) (std. length) 310-LRKCHEVY V-8 272-RH/874 .874” .750” STEEL “B” 203-HG 7.781” 210-LRK (Centerline) (std. length) 310-LRK 272-RHM-904 .903” .810” STEEL “A” 203-HG N/A (Centerline) Series Lightweight Version 272-LO-180 .842” .750” STEEL “A” 203-HG 7.781” N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 272-LO-180/874 .874” .750” STEEL “A” 203-HG 7.781” N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 272-180-904 .903” .810” STEEL “A” 203-HG N/A (8-Centerline) Series (4 ea. .180” Left & Right Offset) 372-RH .842” .750” STEEL “B” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) 372-RHM .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) Lightweight Version 372-RHM-904 .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372-RHM-937 .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372-LO-180 .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) (std. length) blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372-LO-180/874 .874” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372-180-904 .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372-180-937 .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 1271-LSH .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271-LSH/874 .874” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271-LO .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (8-Centerline) 300-LRK (4 ea. .100” Left & Right Offset) 1271-LO-150 .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset) 1271-LO-185 .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .185” Left & Right Offset) 1271-LO-150/874 .874” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset) 1371-LSH .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1300-LRK (extra tall version to fit into late bow-tie “C” (Centerline) blocks with raised lifter bosses) 1371-LO-150 .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1350-LRK (extra tall version to fit into late bow-tie “C” (8-Centerline) blocks with raised lifter bosses) (4 ea. .150” Left & Right Offset) 372-LO-SPL .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses) 372-LO-SPL/904 .903” .810” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses)
SMALL BLOCKCHEVY V-8 WITHSPLAYED VALVEOR SB-2 HEAD
All sets include one set of (8) pcs GB-200 guide bars
BODY BEARINGAPPLICATION PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KITCHEVY V-8 377-RHM-842 .842” .750” STEEL “A” -- N/ASB-2.2 BLOCK (Centerline) (std. length)WITH SB-2.2 HEADS (Lightweight Version) 377-RHM-874 .874” .750” STEEL “A” -- N/A
(Centerline) (std. length) (Lightweight Version) 377-RHM-904 .903” .810” STEEL “A” -- N/A (Centerline) (std. length)
(Lightweight Version) 377-180-842 .842” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377-180-874 .874” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377-180-904 .903” .810” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset)
CHEVY LS-1 V-8 1377LSH .842” .750” ALUMINUM TOP -- -- N/A “C” (Centerline) 375RHM .842” .750” STEEL “A” N/A
(Centerline) -- -- (Lightweight Version) 375LOSPL .842” .750” STEEL “A” -- -- N/A (8 ea. .180” Left & Right Offset) 375RHM904 .903” .810” STEEL “A” N/A
(Centerline) -- -- (Lightweight Version) 375LOSPL904 .903” .810” STEEL “A” -- -- N/A (8 ea. .180” Left & Right Offset) BIG BLOCK 272-96-RH .842” .750” STEEL “B” 203-96 8.281” Int N/ACHEVY V-8 (Centerline) (std. length) 9.250” Ex 276-RHM-904 .903” .810” STEEL “A” 203-96 N/A (Centerline) Series Lightweight Version 272-96-LO-180 .842” .750” STEEL “A” 203-96 8.281” Int N/A (8-Centerline) (std. length) 9.250” Ex (4 ea. .180” Left & Right Offset) 276-180-904 .903” .810” STEEL “A” 203-96 N/A (8-Centerline) Series (4 ea. .180” Left & Right Offset) 372-96-RH .842” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 372-96-RH/874 .874” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 372-96-RHM .842” .750” STEEL “A” 203-96 N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376-RHM-904 .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376-RHM-937 .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372-96-LO-180 .842” .750” STEEL “A” 203-96 8.281” Int N/A (extra tall version to fit late bow-tie (8-Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 376-180-904 .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 376-180-937 .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset)CHRYSLER “R” BLOCK 3272-RH .903” .810” STEEL “A” -- -.250” N/A318-360 CU IN WITH (for blocks & cyl. heads that require pushrod (Centerline)48 DEG. LIFTER BANK ANGLE oiling; pushrod seat location moved up .250”) Lightweight Version
All sets include one set of (8) pcs GB-380 guide bars
All sets include one set of (8) pcs GB-454 guide bars
All sets include one set of (8) pcs GB-502 guide bars
18
Red ZoneTM MAXIMUM ENDURANCE ROLLER LIFTERS
19
Red ZoneTM MAXIMUM ENDURANCE ROLLER LIFTERS BODY BEARINGAPPLICATION PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KITCHRYSLER “B” 3472-RH .903” .810” STEEL “A” -- (std. length) N/A383-440 CU IN. V-8 (Centerline) Lightweight Version 3772-LO-180 .903” .810” STEEL “A” -- -.250” N/A (For use with NEW Indy cyl. heads with (8-Centerline) relocated intake valve position) (4 ea. .180” Left & Right Offset) (Pushrod seat location moved up .250”) 3672-RH .903” .810” STEEL “A” -- -.125” N/A (Pushrod seat location moved up .125”) (Centerline) Lightweight Version 3372-RH .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight VersionCHRYSLER HEMI V-8 3472-RHM .903” .810” STEEL “A” -- (std. length) N/A1956-58 354-392 CU IN (Centerline) Lightweight VersionDONOVAN 417 CU IN 3672-RHM .903” .810” STEEL “A” -- -.125” N/A1964-UP 426 CU IN (Pushrod seat location moved up .125”) (Centerline) Supplied with special tie-bar to work with both- Lightweight Version Standard and 2.000” bore spacing blocks 3372-RH .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight VersionFORD V-8 351 Cleveland Only 3572-RH .874” .750” STEEL “A” -- -- N/A (Centerline)
FORD V-8, 351 SVO, 3972-RH .874” .750” STEEL “A” -- Std. Length N/A289/302, BOSS 302 (Centerline) Lightweight Version 3972-RH/904 .903” 810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972-RH/937 .936” 850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972-YATES180 .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972-Y180/904 .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972-Y180/937 .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset)FORD V-8 429-460 cu. in. 3172-RH .874” .750” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172-RH/904 .903” .810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172-RH/937 .936” .850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172-YATES180 .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172-Y180/904 .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172-Y180/937 .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset)PONTIAC 4-cylinder 151” 1271-XL .842 .750” Aluminum Top **203-HG 7.781” 1243-L(8)Iron Duke (Centerline)
PONTIAC V-8 (1955 & Up) 9672-RH .842 .750” STEEL “A” -- -- N/A (Centerline)
All sets include one set of (8) pcs GB-380 guide bars
All sets include one set of (8) pcs GB-310 guide bars
All sets include one set of (8) pcs GB-380 guide bars
All sets include one set of (8) pcs GB-951 guide bars
All sets include one set of (8) pcs GB-900 guide bars
20
*Patented Technology For Racing in the
ROLL “EZ”........RED-ZONETM Safe!
HARDCORERACERS:
The revolutionary new EZ-ROLLTM bearingoption is exclusive for ISKY RED-ZONETM
Roller Lifters! EZ-ROLLTM “needle-free” rollerbearings solve the age old dilemma of needlebearing overload. Although needle rollerbearings perform well in light to moderately heavy load applications, theoften extreme loading demands of “all out” drag, pro-street, continuous operationendurance and offshore marine applicationshave long required a better performing
alternative. Solution: ISKY’S proprietary solidbearing raceway EZ-ROLLTM Bearing! Spintron® and field test proven over the past 8 years, EZ-ROLLTM bearings carry fargreater loads. Their advanced needle-freedesign and greater surface area to load distribution footprint deliver a solid 350%higher load rating! EZ-ROLLTM, ... becauseneedles really are old news!
OVER 9,000 SETS SOLD SINCE 2007!!!
THE WORLD’S BEST ROLLER LIFTERS
Traditional Needle-Roller Bearings where only 3 to 4 needles carry the burden.
*EZ-ROLLTM Lifters ARE “NEEDLE FREE”!
For your environment, needles are old news! At ISKY, we’ve proven thatthe future of roller lifter development is completely NEEDLE FREE!
The new EZ-ROLLTM bearing option is available in your choice of 3 endurance grades to suit your exact requirements:
The only oil-restrictor friendly lifters in the industry!
HIGHER!EZ-ROLLXTM
Upgraded Epsilon-ZXTM Solid BearingRaceway Material; a super low friction, high-tech alternative to needles. Ideal for offshore marine and other normally aspirated environments where up to 900lbs. valve open spring force is employed.Available in all popular lifter diameters. Forthis grade, add “EZX” to the end of theRed-ZoneTM Roller Lifter part numberwhen ordering. Includes captive guide bar feature.
Additional premium over needles:Chevy & Chrysler V8 . . $275.00 NetFord V8. . . . . . . . . . . . . $350.00 Net
ENTRYLEVEL!EZ-ROLL JRTM
JUST ROLL with our newest member of the EZ-ROLLTM (PATENTED) solid-raceway roller bearing lifter family, theentry level EZ-ROLL JRTM. Designed forNormally Aspirated Small and Big BlockChevy V8, this full body design acceptsboth 5/16” and 3/8” diameter pushrods andis targeted for use with up to 700 lbs. open valve spring pressure for street,drag, marine, oval track, etc... and they’re oil-restrictor friendly too! Includes captive guide bar feature.
HIGHEST!!EZ-ROLLMAXTM
Upgraded Epsilon-ZMAXTM Solid BearingRaceway Material; an “ultra” low friction,high-tech alternative to needles. Ideal forthe most extreme loading environments:• High boost turbo, high HP nitrous &blown gas/alcohol• Offshore marine & all-out, normally aspirated applications
EZ-MAX TM is recommended for ANY .842,.904 or 937 dia lifter installed with over 400lbs. seat and 950-1,300 lbs. valve openspring force.For this grade, add “EZ-MAX” to the endof the Red Zone roller lifter part numberwhen ordering. Includes captive guide bar feature.
Additional premium over needles:Chevy & Chrysler V8 . . $350.00 NetFord V8. . . . . . . . . . . . . $425.00 Net
*Unprecedented in the history of roller lifter development,*EZ-RollTM lifters are protected by US patents #8,464,678 and #8,851,038.
21
Extreme ZoneTM EZ-RollXTM ROLLER LIFTERS
BODY BEARINGAPPLICATION EZ-X PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 372EZJR .842” .750” STEEL “B” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) 372RHEZX .842” .750” STEEL “B” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) 372RHMEZX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) Lightweight Version 372RHM904EZX .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372RHM937EZX .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372LO180EZX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) (std. length) blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372LO180/874EZX .874” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372180904EZX .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372180937EZX .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 1271LSHEZX .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271LSH/874EZX .874” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271LOEZX .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (8-Centerline) 300-LRK (4 ea. .100” Left & Right Offset) 1271LO150EZX .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset) 1271LO185EZX .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .185” Left & Right Offset) 1271LO150/874EZX .874” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset)
1371LSHEZX .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1300-LRK (extra tall version to fit into late bow-tie “C” (Centerline) blocks with raised lifter bosses) 1371LO150EZX .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1350-LRK (extra tall version to fit into late bow-tie “C” (8-Centerline) blocks with raised lifter bosses) (4 ea. .150” Left & Right Offset)
SMALL BLOCKCHEVY V-8
A A B C C C
22
Extreme ZoneTM EZ-RollXTM ROLLER LIFTERS
BODY BEARINGAPPLICATION EZ-X PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 372LOSPLEZX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses) 372LOSPL/904EZX .903” .810” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses) 377RHM842EZX .842” .750” STEEL “A” -- N/A (Centerline) (std. length) (Lightweight Version) 377RHM874EZX .874” .750” STEEL “A” -- N/A
(Centerline) (std. length) (Lightweight Version) 377RHM904EZX .903” .810” STEEL “A” -- N/A (Centerline) (std. length)
(Lightweight Version) 377180842EZX .842” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377180874EZX .874” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377180904EZX .903” .810” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 376EZJR .842” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 37296RHEZX .842” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 37296RH/874EZX .874” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 37296RHMEZX .842” .750” STEEL “A” 203-96 N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376RHM904EZX .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376RHM937EZX .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 37296LO180EZX .842” .750” STEEL “A” 203-96 8.281” Int N/A (extra tall version to fit late bow-tie (8-Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 376180904EZX .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 376180937EZX .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 3272RHEZX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version
3472RHEZX .903” .810” STEEL “A” -- (std. length) N/A (Centerline) Lightweight Version 3772LO180EZX .903” .810” STEEL “A” -- -.250” N/A (For use with NEW Indy cyl. heads with (8-Centerline) relocated intake valve position) (4 ea. .180” Left & Right Offset) (Pushrod seat location moved up .250”) 3672RHEZX .903” .810” STEEL “A” -- -.125” N/A (Pushrod seat location moved up .125”) (Centerline) Lightweight Version 3372RHEZX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version 3472RHMEZX .903” .810” STEEL “A” -- (std. length) N/A (Centerline) Lightweight Version
SMALL BLOCKCHEVY V-8 WITHSPLAYED VALVEOR SB-2 HEAD
CHEVY V-8SB-2.2 BLOCKWITH SB-2.2 HEADS
BIG BLOCKCHEVY V-8
CHRYSLER “R” BLOCK 318-360 CU IN WITH 48 DEG.LIFTER BANK ANGLE
CHRYSLER “B”383-440 CU IN V-8
CHRYSLER HEMI V-81956-58 354-392 CU IN
23
Extreme ZoneTM EZ-RollXTM ROLLER LIFTERS
Extreme ZoneTM EZ-RollMAXTM ROLLER LIFTERS
BODY BEARINGAPPLICATION EZ-X PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 3672RHMEZX .903” .810” STEEL “A” -- -.125” N/A (Pushrod seat location moved up .125”) (Centerline) Supplied with special tie-bar to work with both- Lightweight Version Standard and 2.000” bore spacing blocks 3372RHEZX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version 3972RHEZX .874” .750” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972RH/904EZX .903” 810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972RH/937EZX .936” 850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972YATES180EZX .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972Y180/904EZX .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972Y180/937EZX .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172RHEZX .874” .750” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172RH/904EZX .903” .810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172RH/937EZX .936” .850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172YATES180EZX .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172Y180/904EZX .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172Y180/937EZX .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset)
CHRYSLER HEMI V81956-58, 354-392 CU IN
DONOVAN 417 CU IN1964-UP 426 CU IN
FORD V-8, 351 SVO,289/302, BOSS 302
FORD V-8 429-460 CU IN
372RHEZMAX .842” .750” STEEL “B” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) 372RHMEZMAX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) blocks with raised lifter bosses) Lightweight Version 372RHM904EZMAX .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372RHM937EZMAX .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 372LO180EZMAX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) (std. length) blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372LO180/874EZMAX .874” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 372180904EZMAX .903” .810” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset)
SMALL BLOCKCHEVY V-8
24
Extreme ZoneTM EZ-RollMAXTM ROLLER LIFTERS
BODY BEARINGAPPLICATION EZ-MAX PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 372180937EZMAX .936” .850” STEEL “A” 203-HG N/A (extra tall version to fit into late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 1271LSHEZMAX .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271LSH/874EZMAX .874” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (Centerline) 300-LRK 1271LOEZMAX .842” .750” ALUMINUM TOP 1235-L 6.500” 200-LRK “C” (8-Centerline) 300-LRK (4 ea. .100” Left & Right Offset) 1271LO150EZMAX .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset) 1271LO185EZMAX .842” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .185” Left & Right Offset) 1271LO150/874EZMAX .874” .750” ALUMINUM TOP 1235-L 6.500” 150-LRK “C” (8-Centerline) (4 ea. .150” Left & Right Offset) 1371LSHEZMAX .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1300-LRK (extra tall version to fit into late bow-tie “C” (Centerline) blocks with raised lifter bosses) 1371LO150EZMAX .842” .750” ALUMINUM TOP 1235-L-.350” 6.150” 1350-LRK (extra tall version to fit into late bow-tie “C” (8-Centerline) blocks with raised lifter bosses) (4 ea. .150” Left & Right Offset) 372LOSPLEZMAX .842” .750” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses) 372LOSPL/904EZMAX .903” .810” STEEL “A” 203-HG 7.781” N/A (extra tall version to fit into late bow-tie (8 ea. .180” Left & Right Offset) Series blocks with raised lifter bosses) 377RHM842EZMAX .842” .750” STEEL “A” -- N/A (Centerline) (std. length) (Lightweight Version) 377RHM874EZMAX .874” .750” STEEL “A” -- N/A
(Centerline) (std. length) (Lightweight Version) 377RHM904EZMAX .903” .810” STEEL “A” -- N/A (Centerline) (std. length)
(Lightweight Version) 377180842EZMAX .842” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377180874EZMAX .874” .750” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 377180904EZMAX .903” .810” STEEL “A” -- N/A (8-Centerline) (std. length) (4 ea. .180” Left & Right Offset) 37296RHEZMAX .842” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 37296RH/874EZMAX .874” .750” STEEL “B” 203-96 8.281” Int N/A (extra tall version to fit into late bow-tie (Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) 37296RHMEZMAX .842” .750” STEEL “A” 203-96 N/A (extra tall version to fit into late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376RHM904EZMAX .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 376RHM937EZMAX .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (Centerline) Series blocks with raised lifter bosses) Lightweight Version 37296LO180EZMAX .842” .750” STEEL “A” 203-96 8.281” Int N/A (extra tall version to fit late bow-tie (8-Centerline) (std. length) 9.250” Ex blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset)
SMALL BLOCKCHEVY V-8
SMALL BLOCKCHEVY V-8 WITHSPLAYED VALVEOR SB-2 HEAD
CHEVY V-8SB-2.2 BLOCKWITH SB-2.2 HEADS
BIG BLOCKCHEVY V-8
25
Extreme ZoneTM EZ-RollMAXTM ROLLER LIFTERS
BODY BEARINGAPPLICATION EZ-MAX PART NO. DIA. DIA. BODY TYPE ISKY PUSHROD LENGTH REV-KIT 376180904EZMAX .903” .810” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 376180937EZMAX .936” .850” STEEL “A” 203-96 N/A (extra tall version to fit late bow-tie (8-Centerline) Series blocks with raised lifter bosses) (4 ea. .180” Left & Right Offset) 3272RHEZMAX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version
3472RHEZMAX .903” .810” STEEL “A” -- (std. length) N/A (Centerline) Lightweight Version 3772LO180EZMAX .903” .810” STEEL “A” -- -.250” N/A (For use with NEW Indy cyl. heads with (8-Centerline) relocated intake valve position) (4 ea. .180” Left & Right Offset) (Pushrod seat location moved up .250”) 3672RHEZMAX .903” .810” STEEL “A” -- -.125” N/A (Pushrod seat location moved up .125”) (Centerline) Lightweight Version 3372RHEZMAX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version 3472RHMEZMAX .903” .810” STEEL “A” -- (std. length) N/A (Centerline) Lightweight Version 3672RHMEZMAX .903” .810” STEEL “A” -- -.125” N/A (Pushrod seat location moved up .125”) (Centerline) Supplied with special tie-bar to work with both- Lightweight Version Standard and 2.000” bore spacing blocks 3372RHEZMAX .903” .810” STEEL “A” -- -.250” N/A (for blocks & cyl. heads that require pushrod (Centerline) oiling; pushrod seat location moved up .250”) Lightweight Version 3972RHEZMAX .874” .750” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972RH/904EZMAX .903” 810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972RH/937EZMAX .936” 850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3972YATES180EZMAX .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972Y180/904EZMAX .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3972Y180/937EZMAX .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172RHEZMAX .874” .750” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172RH/904EZMAX .903” .810” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172RH/937EZMAX .936” .850” STEEL “A” -- Std. Length N/A (Centerline) Lightweight Version 3172YATES180EZMAX .874” .750” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172Y180/904EZMAX .903” .810” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset) 3172Y180/937EZMAX .936” .850” STEEL “A” -- Std. Length N/A (8-Centerline) (8 ea. .180” Left Offset)
BIG BLOCKCHEVY V-8
CHRYSLER “R” BLOCK 318-360 CU IN WITH 48 DEG.LIFTER BANK ANGLE
CHRYSLER “B”383-440 CU IN V-8
CHRYSLER HEMI V-81956-58 354-392 CU IN
DONOVAN 417 CU IN1964-UP 426 CU IN
FORD V-8, 351 SVO,289/302, BOSS 302
FORD V-8 429-460 CU IN
26
LIFTER BORE BUSHINGS
Isky Lifter Bore Bushings are precision made from a special bronze alloy that lasts 2-4 times longer than most others. They also prevent excessive “Scuffing” of Roller Lifter Bodies.Requires machining of lifter bores prior to installation.
UNIVERSAL STYLE (NON-KEYED): FOR USE WITH CONVENTIONAL “TIE-BAR” ROLLER LIFTERS.
Part No. Bushing O.D. Bushing I.D. Overall LengthLB-842 1.002” .842” 1.700”LB-874 1.002” .874” 1.750”LB-904 1.002” .904” 1.750”LB-937 1.062” .937” 1.750”
KEYED STYLE (FOR USE WITH KEYWAY ROLLER LIFTERS)
Part No. Bushing O.D. Bushing I.D. Overall Length ApplicationKLB-936 1.062” .936” 1.990” Small & Big Block Chevy V-8 For use with 936 & 937 Prefix Isky Keyway Roller LiftersKLB-937 1.062” .936” 2.070” Ford V-8 For use with 937 Prefix Isky Keyway Roller LiftersKLB-1062 1.188” 1.058” 2.090” Big Block Chevy V8 For use with 1062 Prefix Isky Keyway Roller Lifters
Hi-tech EZ-ROLLTM Keyway-Lifters.937 & 1.062 dia Keyway style REDZONETM Roller Lifters equipped standard with our exclusive NEEDLE-FREE EZ-ROLLTM Bearings!
The proliferation of modern valve-trains (i.e. aggressive camprofiles, higher rocker arm ratios and 1,200 lb. PLUS open pressure valve springs) have often seen even the oversized/overpriced specialty roller lifters quickly succumb to premature
needle bearing over-load failure! The phenomenal success ofour “needle free” EZ-ROLLTM Bearing option for conventionalIsky RED-ZONETM “tie-bar” style Roller Lifters has spawned theirextension to the next platform:
EZ-ROLLTM Pushrod Overall Key Keyway Lifter Body Bearing Pushrod Seat Body Weight Seat Height Length Height Part No. Diameter Diameter Location Style (Grams) (Fig A) (Fig B) (Fig C) •936KEZX .936” .850” (16) Centered Open Body 119 g 1.290” 2.130” 2.030 •936K050EZX .936” .850” (16) .050” Offset Open Body 119 g 1.290” 2.130” 2.030 •936K150EZX .936” .850” (16) .150” Offset Open Body 119 g 1.290” 2.130” 2.030 •937KEZX .936” .850” (16) Centered Open Body 123 g 1.290” 2.280” *2.180 •937K050EZX .936” .850” (16) .050” Offset Open Body 123 g 1.290” 2.280” *2.180 •937K150EZX .936” .850” (16) .150” Offset Open Body 123 g 1.290” 2.280” *2.180 -SL1062KEZMAX 1.061” .920” (16) Centered Shrouded Body 144 g 1.440” 2.150” 2.060
*Key Height is raised .150”•EZX TM bearing standard: add $50.00 premium for EZ-MAXTM
-EZMAXTM bearing standard:
“Traditional Needle-Roller Bearing and it’s small load distribution footprint.”
EZ
R
O L L B E A RI N
G
precision ground polished body
936KSL-1062
By popular demand of major engine builders and racers across the country, weproudly announce this revolutionary patent-pending design technology is nowavailable for Keyway Style Roller Lifters! After months of development at the Isky Spintron® research facility and in the field, the fail-safe peace of mind alternative to needle-roller bearings will soon change the way professional racers view their roller lifter needs forever! EZ-ROLLTM Keyway Roller Lifters aresuitable for hi-end circle track, offshore marine and drag race applications employing modified lifter bore spaced blocks (where it’s difficult or impossible to install tie-bar style rollers). See page 28 for the EZXTM & EZMAXTM EZ-ROLLTMlifter bearing descriptions.
ISKY’s Revolutionary New Wide FootPrint Low Friction EZ-Roll Bearing!
27
LS-1 CHEVY V8 350 CU. IN. (1997-UP)
“B-HIVE ” Form Valve Springs:
We are now offering two high performance “B-HIVETM” Valve Springs that are “drop-in” replacements for the Stock LS-1 “B-HIVETM” spring. Both Springs are compatible with stockretainers and locks... but we highly recommend for increased performance, the use of our 135-ST steel retainer and VL-500 Machined Bead Locks (see below).
TM
“TOP” “BOTTOM” RATE RETAINER PART RETAINER LOCATER MAT’L SEAT OPEN PER COIL MAX & LOCK NO. END END PRESS PRESS INCH BIND LIFT COMBO OD/ID OD/ID PART NO. 1.055” 1.290” Super clean 130 Lbs. 320 Lbs. 135-ST 165-A .660” .885” Chrome Silicon @1.800” @1.200” 310 1.140” .600” VL-500 OVATE Wire 1.015” 1.290” “Tool Room” 120 Lbs. 360 Lbs. 135-ST 195-A .630” .905” Mat’l/Specially @1.800” @1.175” 380 1.100” .625” VL-500 Processed Round wire
Machined Steel Retainers:
(For use with 165-A and 195-A “B-HIVETM” Valve Springs)
Our P/N 135-ST Steel Retainer weighs the same as the Stock LS-1 “Stamped” Retainer but is superior in strength. It is machined from 4130 Chromemoly Steel & Heat Treated for Maximum “Pull-Thru” Strength. The combination of the 135-ST steel retainer and our “Machined” VL-500 Bead Locks yields a more precise,consistent installed height and gives added insurance in your LS-1 Engine with more aggressive hydraulic roller cam profiles at higher RPM. This combination can be used with stock LS-1 “B-HIVETM” springs as well.
LS-1 Dual Valve Springs:
When looking for the increased reliability of a “Drop-In” Dual Valve Spring(No Machining Required) our High Quality 4905 is manufactured from Hi-Tensile, Chrome Silicon Alloy and will accommodate Hydraulic RollerCams up to .650” Valve Lift comfortably. When converting from the stockBeehive to the 4905 Dual Springs, it is also required to use our matching185-ST Steel Retainers, 185-VSL Spring Locaters and IVS-400 Oil Seals.
P A R T N U M B E R VALVE STEEL SPRING VALVE OUTER INNER SEAT OPEN RATE COIL MAX SPRINGS RETAINERS LOCATERS SEALS OD/ID OD/ID PRESS PRESS PER INCH BIND NET LIFT
4905 185-ST 185-VSL IVS-400 1.290” .940” 125 lbs. 360 lbs. 360 1.065” .650” .940” .690” @1.800” @1.150”
With the increased popularity of the Late Model LS-1 Chevy V8 Platform, we are pleased to introduce the following new Valve Train Components.
28
SMALL BLOCK CHEVY V8 283-327-350-400 CU. IN. (1955-91)
“TOP” “BOTTOM” RATE PART RETAINER LOCATER MAT’L SEAT OPEN PER COIL MAX RETAINER NO. END END PRESS PRESS INCH BIND LIFT PART NO. OD/ID OD/ID 1.055” 1.290” Super clean 130 Lbs. 320 Lbs. 165-A .660” .885” Chrome Silicon @1.800” @1.200” 310 1.140” .600” 165 ST OVATE Wire 1.015” 1.290” “Tool Room” 120 Lbs. 360 Lbs. 195-A .630” .905” Mat’l/Specially @1.800” @1.175” 380 1.100” .625” 165 ST Processed Round wire
We’ve been receiving many requests to adapt the LS-1 Style “B-HIVETM” Valve Springs to the earlier Small Block Chevy V-8’s (1955-91) for Moderate Performance Hydraulic, Hydraulic Roller and Solid Lifter Cam Applications. Using either the 165-A or 195-A in these applications will require the use of our 165-ST Steel Retainer which is compatable with both stock and our VL-32 (11/32) Valve locks.
Big Block Chevy V-8
For the Big Block Chevy V-8 1967-95 and Gen-6 Engines, we have recently introduced our newpart no. 175-A “B-HIVETM” Valve Springs, designed for use in Moderate Performance Hydraulic &Hydraulic Roller Applications. When using the 175-A valve spring, it is required to use our 169-STmatching steel retainer which is compatable with either stock or Isky VL-3/8, (3/8”) valve locks.
“TOP” “BOTTOM” RATE PART RETAINER LOCATER MAT’L SEAT OPEN PER COIL MAX RETAINER NO. END END PRESS PRESS INCH BIND LIFT PART NO. OD/ID OD/ID 1.095” 1.445” Super clean 155 Lbs. 375 Lbs. 175-A .650” 1.000” Chrome Silicon @1.880” @1.280” 370 1.210” .600” 169-ST OVATE Wire
Street, Oval & Drag (Hydraulic & Solid Applications)8205, 8305, 8005-A, 6005 DUAL WITH DAMPER
Our most popular Chrome Silicon Valve Springs, covering a wide variety of applications and installed heights.
8205 1.530” O.D. Installed Height @ 1.900”: Solid Lifter Camshafts Only
8305 1.510” O.D. Installed Height @ 1.875”: Solid Lifter Camshafts Only
8005-A 1.530” O.D. Installed Height @ 1.875”: Hydraulic & Solid Lifter Camshafts
6005 1.430” O.D. Installed Height @ 1.750”: Hydraulic Camshafts Only
205-D, 805-DO, 3105-D, 3605-D
Compatible with stock retainers & valve seals for usewith both hyd. & Solid lifter cams.Also, ideally suited for N.H.R.A. stock eliminatorclasses where a stock O.D. valve spring is required.
*235-D Small Block Chevy V-8
Ideal for Oval Track Classes. Will handle up to .550”Net Valve Lift. Requires Isky Part No. 707-STA SteelRetainer to obtain 1.750” installed height.
See page 39 for information on our new P/N 295-D Tool Room single with damper.
*205-D Small Block Chevy V-8 & V-6, Buick V-6 (late model)
*805-D Big Block Chevy V-8
*3105-D 340-360 Mopar V-8 302 & 351 Ford Windsor V-8
*3605-D Big Block Chevy V-8 383-440 Chrysler V-8 429-460 Ford V-8 360-390 Ford V-8 302-351 Boss Ford V-8 360-390-401 AMC V-8
O.E.M. Factory Replacement
29
ISKY VALVE SPRINGS
INDIVIDUAL SPRING PART NUMBERS (IN) INNER RATE MAXPART COLOR (M) MIDDLE SEAT OPEN PER COIL NETNO. TYPE/MAT’L CODE (O) OUTER O.D. I.D. PRESSURE PRESSURE INCH BIND LIFT
9901-A MULTI-COIL NATURAL (IN) --- .885 .640 340 lbs 1000 lbs 740 1.140 .850” NATURAL (M) --- 1.200 .885 @2.100” @1.200” .900” NATURAL (O) --- 1.660 1.200
9801-A MULTI-COIL NATURAL (IN) --- .885 .640 330 lbs 925 lbs 740 1.140 .800” NATURAL (M) --- 1.200 .885 @2.025” @1.225” .850” NATURAL (O) --- 1.660 1.200
9701 MULTI-COIL NATURAL (IN) --- .885 .640 285 lbs 790 lbs 680 1.140 .750” NATURAL (M) --- 1.200 .885 @2.000” @1.250” .800” NATURAL (O) --- 1.650 1.200
4905 DUAL NATURAL (IN) --- .940 .690 125 lbs 360 lbs 360 1.065 .650” (CHROME SILICON) NATURAL (O) --- 1.290 .940 @1.800” @1.150”
3005 DUAL NATURAL (IN) --- .950 .715 80 lbs 230 lbs 300 .770 .500” (CHROME SILICON) NATURAL (O) --- 1.255 .950 @1.400” @.900”
4205 DUAL WHITE (IN) 1006-W .915 .660 130 lbs 290 lbs 320 1.020 .500” (CHROME SILICON) GREY (O) 205-G 1.240 .925 @1.687” @1.187”
4005 DUAL GREY (IN) 206-G .925 .690 115 lbs 240 lbs 250 .960 .500” (CHROME SILICON) GREY (O) 205-G 1.240 .925 @1.687” 1.187”
625/626 DUAL NATURAL (IN) --- .900 .675 75 lbs 240 lbs 300 .940 .550” (CHROME SILICON) NATURAL (O) --- 1.235 .905 @1.687” @1.137”
9705 DUAL W/DAMPER NATURAL (IN) --- 1.079 .767 250 lbs 675 lbs 570 1.150 .750” (H-11 TOOL STEEL) BLUE (O) --- 1.625 1.189 @1.950” @1.200”
9685 DUAL W/DAMPER YELLOW (IN) --- 1.065 .770 240 lbs 685 lbs 550 1.150 .750” (ISKYLOY ENDURANCE) YELLOW (O) --- 1.625 1.175 @2.000” @1.250”
9425 DUAL W/DAMPER NATURAL (IN) --- 1.040 .740 250 lbs 620 lbs 520 1.190 .700” (Tool Room Outer/Silicon Inner) NATURAL (O) --- 1.560 1.145 @1.950” @1.250”
9385 DUAL W/DAMPER NATURAL (IN) --- 1.040 .740 245 lbs 600 lbs 500 1.180 .720”PLUS (Tool Room Outer/Silicon Inner) SILVER/RED (O) --- 1.560 1.145 @2.000” @1.280”
9385 DUAL W/DAMPER NATURAL (IN) --- 1.040 .740 240 lbs 600 lbs 500 1.180 .720” (ISKYLOY ENDURANCE) SILVER (O) --- 1.560 1.145 @2.000” @1.280”
9375/85 DUAL W/DAMPER NATURAL (IN) --- 1.040 .740 250 lbs 580 lbs 470 1.190 .680”PLUS (Tool Room Outer/Silicon Inner) SILVER/ORANGE (O) --- 1.560 1.145 @1.970” @1.290”
9375 DUAL W/DAMPER ORANGE (IN) --- 1.040 .740 230 lbs 560 lbs 480 1.190 .680”PLUS (Tool Room Outer/Silicon Inner) SILVER/ORANGE (O) 1.560 1.145 @1.970” @1.290”
We make Valve Springs to cover all applications, from street toall-out competition in single, dual and multi-coil designs.
30
ISKY VALVE SPRINGS (CONTINUED)
INDIVIDUAL SPRING PART NUMBERS RATE MAXPART COLOR (IN) INNER SEAT OPEN PER COIL NETNO. TYPE/MAT’L CODE (O) OUTER O.D. I.D. PRESSURE PRESSURE INCH BIND LIFT
9365 DUAL W/DAMPER BLUE (IN) --- 1.040 .740 235 lbs 560 lbs 470 1.170 .680”PLUS (Tool Room Outer/Silicon Inner) SILVER/ORG (O) --- 1.560 1.145 @1.950” @1.270”
9365 DUAL W/DAMPER GREEN (IN) 875-G 1.025 .740 215 lbs 550 lbs 460 1.170 .680” (CHROME SILICON) GREEN (O) 975-G 1.550 1.135 @1.950” @1.270”
9315 DUAL W/DAMPER RED (IN) --- 1.025 .740 210 lbs 520 lbs 480 1.130 .660” (CHROME SILICON) RED (O) --- 1.550 1.135 @1.900” @1.240”
9005 DUAL W/DAMPER NATURAL (IN) 806-S 1.005 .725 185 lbs 465 lbs 430 1.160 .650” (CHROME SILICON) ORANGE (O) 805-DO 1.530 1.110 @1.875” @1.225”
9265 DUAL W/DAMPER NATURAL (IN) 806-S 1.005 .725 175 lbs 510 lbs 490 1.130 .675” (CHROME SILICON) YELLOW (O) 3605-D 1.540 1.115 @1.875” @1.200”
6205 DUAL W/DAMPER NATURAL (IN) 806-S 1.025 .725 175 lbs 350 lbs 320 1.160 .550” (CHROME SILICON) ORG/YELL (O) 305-DHS 1.430 1.070 @1.812” @1.260”
9205 DUAL W/DAMPER PURPLE (IN) 826-P 1.040 .755 170 lbs 475 lbs 435 1.175 .675” (CHROME SILICON) PURPLE (O) 825-DP 1.550 1.130 @1.950” @1.250”
8305 DUAL W/DAMPER --- (IN) --- 1.005 .730 160 lbs 380 lbs 370 1.175 .600” (CHROME SILICON) --- (O) --- 1.510 1.110 @1.875” @1.275”
5105 DUAL W/DAMPER RED (IN) 906-RH 1.000 .730 150 lbs 345 lbs 370 .940 .530” (CHROME SILICON) GREEN (O) 905-D 1.430 1.075 @1.531” @1.000”
8205 DUAL W/DAMPER ORG/YELL (IN) 926-OY 1.005 .730 140 lbs 430 lbs 440 1.170 .650” (CHROME SILICON) BROWN (O) 815-DB 1.530 1.110 @1.900” @1.250”
8005-A DUAL W/DAMPER BLUE (IN) 906-AM 1.005 .730 135 lbs 395 lbs 400 1.160 .650” (CHROME SILICON) ORANGE (O) 805-DO 1.530 1.110 @1.875” @1.225”
6105 DUAL W/DAMPER RED (IN) 906-RH 1.000 .730 135 lbs 315 lbs 330 1.120 .550” (CHROME SILICON) ORG/YELL (O) 305-DHS 1.430 1.070 @1.812” @1.260”
6005 DUAL W/DAMPER BLUE (IN) 906-AM 1.005 .730 135 lbs 285 lbs 275 1.120 .550” (CHROME SILICON) ORG/YELL (O) 305-DHS 1.430 1.070 @1.750” @1.200”
5005 DUAL W/DAMPER BLUE (IN) 906-AM 1.005 .730 125 lbs 285 lbs 320 .980 .500” (CHROME SILICON) GREEN (O) 905-D 1.430 1.075 @1.531” @1.031”
935-DR OUTER W/DAMPER RED --- --- 1.550 1.120 160 lbs 340 lbs 380 1.200 .550” (CHROME SILICON) @1.850” @1.370”
*3105-D OUTER W/DAMPER NATURAL --- --- 1.490 1.076 130 lbs 320 lbs 370 1.100 .500” (CHROME SILICON) @1.700” @1.200”
*805-DO OUTER W/DAMPER ORANGE --- --- 1.530 1.110 120 lbs 290 lbs 330 1.120 .525” (CHROME SILICON) @1.875” @1.350”
235-D OUTER W/DAMPER BLUE --- --- 1.260 .886 130 lbs 320 lbs 350 1.150 .550” (CHROME SILICON) @1.750” @1.200”
*205-D OUTER W/DAMPER YELLOW --- --- 1.260 .886 115 lbs 268 lbs 310 1.160 .490” (CHROME SILICON) @1.700” @1.210”
*3605-D OUTER W/DAMPER YELLOW --- --- 1.540 1.115 110 lbs 300 lbs 360 1.130 .525” (CHROME SILICON) @1.875” @1.350”
305-DHS OUTER W/DAMPER ORG/YELL --- --- 1.430 1.070 95 lbs 185 lbs 200 1.120 .450” (CHROME SILICON) @1.812” @1.362”
905-D OUTER W/DAMPER GREEN --- --- 1.430 1.075 85 lbs 200 lbs 250 .960 .450” (CHROME SILICON) @1.531” @1.081”
205-G OUTER GREY --- --- 1.240 .925 85 lbs 165 lbs 170 .930 .475” (CHROME SILICON) @1.687” @1.210”
*OEM Factory Replacement
31
Chevrolet 265-350
Chevrolet 396-454
Chevy II 4 & 6 Cyl.292 Truck
GMC 6 Cyl. (Not V-6)Corvair 1960-69Chevy V-6 90O
Chry-Ply 277-301-318Chry-Dodge-Ply 273-318-340Chrysler “B”383-440
Chrysler Hemi 51-58
Chrysler 426 Hemi
Ford 221-302 (Fairlane)Ford 351 ClevelandFord Boss 302-351Ford V8 272-292-312Ford 332-352-361 390-406-427-428
Ford 429 Wedge
Ford 6 Cyl(All Exc. Falcon)Ford Falcon 144-170-200-250Oldsmobile V-8 ‘49-64Oldsmobile 1965 & up330-455Olds. f-85 215 cu. in.Pontiac V8 1955-Up
Pontiac 4-Cyl 151” Iron Duke
American Mtrs. 290-401Buick V-6 198-225Buick Spec. 215 Alum., 340 IronBuick V8 53-56 & 57-66Buick V8 ‘68 & up 350Buick V8 400-455, ‘67 & upBuick V-6 Even Fire 231”Valiant 6 Cyl.
235-D @ 1.7506005 @ 1.750205-D @ 1.7004205 @ 1.6876105 @ 1.8128005-A @ 1.8758305 @ 1.8753605-D @ 1.875805-DO @ 1.875
205-D @ 1.7006005 @ 1.750
1006W @ 1.6874005 @ 1.687205-D @ 1.7006005 @ 1.6876005 @ 1.687/1.7208005-A @ 1.8753605-D @ 1.875
6005 @ 1.8128005-A @ 1.830
6005 @ 1.7506005 @ 1.7508005-A @ 1.8756005 @ 1.7508005-A @ 1.8756205 @ 1.8758005-A @ 1.830
305-D @ 1.7506005 @ 1.7501005W-206G @ 1.6256005 @ 1.7505005 @ 1.5316005 @ 1.750625-626 @ 1.6875005 @ 1.531
8005-A @ 1.875
8005-A @ 1.830625-626 @ 1.687625-626 @ 1.6871006W @ 1.530625-626 @ 1.6877005 @ 1.687625/626 @ 1.687305D @ 1.625
707-STA507-ST707-ST707-AL507-STA347-ST347-ST347-ST347-ST
707-ST507-ST
267-AL707-AL707-ST347-STSee Catalog3607-ST3607-ST
3607-ST4107-ST4107-ST
See CatalogSee Catalog507-STA507-ST3607-ST3607-ST507-STA
507-ST507-ST327-ST507-ST927-ST507-ST707-AL927-ST
507-STA
3607-ST627-ST707-AL1007-AL627-ST1007-AL707-AL247-AL
NONE568 11/32NONE208 11/32568 11/32NONENONENONENONE
NONE1258 11/32
NONE208 (80 H.P. Eng. Only)NONENONE1258 See Catalog1258 3/8NONE
1258 3/81258 5/161258 5/16
1258 See Catalog1258 11/32NONE208 11/32NONENONE1258 11/32
NONE208 11/32208 5/16NONENONENONE208 11/32NONE
3608 11/32
1258 3/8NONENONENONENONENONENONENONE
9315 @ 1.9009265 @ 1.8759365 @ 1.9509425 @ 1.9509385 @ 2.0009265 @ 1.8759705 @ 1.9509315 @ 1.9009425 @ 1.9509685 @ 2.0009365 @ 1.9509385 @ 2.0004205 @ 1.6876205 @ 1.750
9205 @ 1.9006005 @ 1.6876005 @ 1.687/1.7209265 @ 1.8759425 @ 1.930
9315 @ 1.9209265 @ 1.8509425 @ 1.9509705 @ 1.9509265 @ 1.8759425 @ 1.9509425 @ 1.9506005 @ 1.750
6205 @ 1.8759705 @ 1.9509425 @ 1.9509701 @ 2.0006205 @ 1.750
4205 @ 1.6876005 @ 1.7506005 @ 1.687
4205 @ 1.6875105 @ 1.5319265 @ 1.8759205 @ 1.9009425 @ 1.9506205 @ 1.750
4205 @ 1.6871005W-1006W @ 1.5304205 @ 1.6876105 @ 1.6879365 @ 1.9504205 @ 1.625
275-ST507-STA91-TI/275-ST91-TI/275-ST91-TI/275-ST347-ST975-TI275-ST91-TI/275-ST975-TI91-TI/275-ST91-TI/275-ST707-AL507-ST
91-TI/275-ST347-STSee Catalog3607-ST91-TI/275-ST
91-TI/275-ST4107-ST91-TI/275-ST975-TI507-STA91-TI/275-ST91-TI/275-ST507-ST
3607-ST975-TI91-TI980-TI/10507-ST
327-ST507-ST507-ST
707-AL927-ST507-STA91-TI/275-ST91-TI/275-ST3607-ST
707-AL1007-AL627-ST1007-AL91-TI/275-ST247-AL
3608 11/323608 11/323608 11/323608 11/323608 11/32NONE3708 3/8NONENONE3708 3/8NONENONE208 11/321258 11/32
3608 11/32NONE1258 See Catalog1258 3/81258 3/8
3608 3/81258 5/163608 5/163708 5/163608 11/32
208 11/32
NONE3708 11/32NONE3708 11/32208 11/32
208 5/16508 11/32NONE
208 11/32NONE3608 11/323608 11/323608 11/321258 3/8
NONENONENONENONENONE208 3/8
StockOuter
StockHeight& 906 AM @ NONE 9265 @ 1.812 3607-ST 1258 3/8Stock
StockOuter & 1006W @ 1.812 NONEChevy 6 37-53 & 54-62 267-AL
ENGINE
HYDRAULICHI-REV SOLID
SPRING INSTALLEDHEIGHT
HOLE SAWREQUIRED ROLLER
HOLE SAWREQUIRED
SPRING INSTALLEDHEIGHT
SAW PILOT SAW PILOT
ISKYSPRINGRETAINER
ISKYRETAINERAL-AlumTI-TitaniumST-Steel
32
OUTER INNER VALVE MAX SPRING SPRING SPRING SPRING INSTALLED SEAT COIL BIND RATE LBS O.D. O.D.ENGINE MAKE YR/MODEL PART NO. HEIGHT PRESSURE RETAINER HEIGHT PER INCH I.D. I.D.
A/Healey 4 cyl. BMC “C” Type 906AM 1.687 105 lbs Stock 1.060 --- --- 1.005 Stock Outer .730A/Healey 6 cyl. BMC “C” Type 906AM 1.594 94 lbs Stock 1.060 --- --- 1.005 Stock Outer .730Alpha Romeo Early 4 Cyl. DOHC JA-005 1.312 105 lbs Stock .860 200 1.145 .855 JA-006 .875 .635Alpha Romeo Late 4 Cyl. DOHC 455-D 1.350 112 lbs Stock .850 225 1.210 .855 JA-006 .925 .635Anglia (Street & Comp.) VWE-005 1.250 80 lbs AN-007 .720 260 1.095 .820 SP-006 .815 .625Anglia (Super Comp.) VWE-005 1.250 100 lbs AN-007 .720 320 1.095 .815 SP-116 .815 .605Anglia GT Cross Flow Hd 66 & Up VWE--005 1.200 90 lbs AN-007 .720 260 1.095 .820 Cortina-Pinto SP-006 .815 .625Anglia Cosworth VWE-005 1.250 80 lbs Stock .720 260 1.095 .820 SP-006 .815 .625BMW S.O.H.C. 2002-1600 625 1.550 120 lbs Stock .970 300 1.235 .905 626 .900 .675Datsun S.O.H.C. L-16, L-24 1005-W 1.650 115 lbs 1624-ST .940 250 1.320 .935 206-G .985 .690Datsun 1200 (A-12) 455-D 1.500 80 lbs Stock .850 225 1.210 .855 JA-006 .855 .635Datsun S.O.H.C. L-16, L-18, L-24 7005 1.700 130 lbs 1624-ST .970 280 1.340 1.000 1.000 .748Ford Pinto 2000 455 1.400 85 lbs 457-AL .850 270 1.210 .925 456 .925 .685Renault Gordini/ 456-INNER 1.420 92 lbs Stock .910 270 --- .925Lotus Europa Stock Outer .685Ford Pinto/Capri 2300 cc 905-D 1.480 95 lbs 347-ST .960 240 1.430 --- 1.075Ford V-6 2600 cc 905-D 1.450 100 lbs 4107-AL .960 240 1.430 --- 1.075Ford V-6 2800 cc 905-D 1.450 100 lbs 4107-ST .960 240 1.430 --- 1.075Fiat D.O.H.C. 124/125 455 1.417 114 lbs Stock .900 230 1.210 .905 626 .925 .675Jaguar 6 Cyl. DOHC JA-005 1.312 110 lbs Stock .860 200 1.145 .855 JA-006 .875 .635MGA-MGB 56 & Up MG-05 1.560 115 lbs 3607-ST 1.060 320 1.430 1.005 MG-06 1.075 .730Porsche 53-71 625-626 1.560 110 lbs PO-07 PO-17 .970 300 1.235 .905 .900 .675Sprite (Street & Comp.) BMC “A” Type VWE-005 1.187 100 lbs SP-007 .720 260 1.095 .820 SP-006 .815 .625Sprite (Super Comp.) BMC “A” Type VWE-005 1.187 115 lbs SP-007 .720 320 1.095 .815 SP-116 .815 .605Sunbeam-Hillman OHV 625 1.710 (Remove 70 lbs Stock .970 300 1.235 .905 626 Bot. Ret. & Shims) .900 .675Toyota Corolla Hemi 71 & Up 455 1.480 105 lbs (See Pg. 97) .940 230 1.210 .905 626 .925 .675Toyota 18RC SOHC Stock Outer Stock Ht. 80 lbs Stock .970 --- --- .905 626 Inner .675Toyota 20RC SOHC Stock Outer 1.594 93 lbs Stock --- --- --- .905 626 Inner .675Toyota 1200 455 1.510 100 lbs STMR .930 230 1.210 .905 626 .925 .675Triumph (Street & Comp.) Spitfire VWE-005 1.187 100 lbs Stock .720 260 1.095 .820 SP-006 .815 .625Triumph (Super Comp.) Spitfire VWE-005 1.187 115 lbs Stock .720 320 1.095 .815 SP-116 .815 .605Triumph TR-2-3-4 TR-2-3-4 TR-05 1.625 100 lbs 927-ST 1.060 320 1.430 1.005 TR-06 1.075 .730Volkswagen 61 & Up 40 HP 205-G 1.530 100 lbs V-007 .970 170 1.240 --- .925Volkswagen 61 & Up 40 HP V-005D 1.530 135 lbs V-007 .970 240 1.250 --- .925Volks-Porsche 411-914 205-G 1.530 100 lbs Stock .970 170 1.240 --- .925Volks-Porsche 411-914 V-005D 1.530 135 lbs 327-ST .970 240 1.250 --- .925Volvo B-16 B-18 625 1.625 98 lbs (See Pg. 98) .970 300 1.235 .905 626 .900 .675
VALVE SPRING KITSVALVE SPRING KITS
LATE MODEL HONDA/ACURA MOTORSLATE MODEL HONDA/ACURA MOTORSWe are pleased to offer our new Fast-ZoneTM, High Performance Harmoincally Dampened Valve Spring Kits for the popular late model Honda 4-CYL SOHC and DOHC Platforms.
Isky Valve Spring Kits are engineered for street or race applications.All kits are drop-in installations. In some cases with ihger lift cams,the only modification required is machining the valve guide to allowfor additional retainer to seal clearance.
Isky Valve Springs are wound from the finest quality, super cleanchrome-silicon wire and processed for maximum durability and sustained performance.
HONDA CIVIC D16A6 1.6L SOHCHONDA CIVIC D16A6 1.6L SOHCThe Civic kit consists of Single Valve Springs, Titanium Retainers and ExhaustValve Spring Locaters. No machining required for installation.
KIT COMPONENTSKit (16) (16) (8) ExhaustPart Valve O.D. Seat Open Titanium Spring Coil MaxNo. Springs I.D. Press. Press. Retainers Locaters Bind Lift
12300 306-S .934” 65 lbs 155 lbs 116-TI 116-VSL 1.080” .475” .650” @1.670” @1.220”Note: Isky 306-S single valve springs are compatible with stock steel retainers. However, stock retainers weigh 11.4 grams and our 116-TI is only 6 grams (a considerable weight advantage for the high revving enthusiast)! Retain stock intake locaters but discard stock exhaust locatersand replace with Isky 116-VSL for a uniform intake/exhaust installed valve spriing height. Use stock valve locks.
VALVE SPRING KITSVALVE SPRING KITS
HONDA/ACURA DOHC VTECB Series (B-16A, B-17A, B-18C)H-22 Series
HONDA/ACURA DOHC VTEC
The DOHC VTEC kit consists of Dual Harmonically DampenedValve Springs, Hard-Seat Spring Locaters and Titanium Retainers. No machining is required for installation.
Although compatible with stock retainers, for sustained highrpm we highly recommend Isky 119-TI Titanium Retainers asthey offer a tremendous weight savings. See chart below.
KIT COMPONENTSKit (16) (16) (16)Part Valve Outer Inner Seat Open Titanium Spring Coil MaxNo. Springs OD/ID OD/ID Press. Press. Retainers Locaters Bind Lift
12700 3405 1.169” .885” 80 lbs 190 lbs 119-TI 119-VSL .760” .470” “B” Series .885” .675” @1.320” @.850”12800 3505 1.169” .885” 78 lbs 195 lbs 119-TI 119-VSL .880” .470” “H-22” Series .885” .659” @1.400” @.930”Note: retain stock valve locks.
Weight Comparison (grams) Stock Retainers 13.5 Isky 119-TI (titanium) 9.0
VALVE SPRING KITSVALVE SPRING KITS
ACURA B-18A/B 1.8L DOHC(NON-VTEC)ACURA B-18A/B 1.8L DOHC(NON-VTEC)
Several options are available for the B-Series Acura. The 406-SSingle Outer is a great Harmonically Dampened “Stock Replacement” Valve Spring for pure Stock Cams and iscompatible with Stock Retainers, Locaters and Valve Locks.
When converting to Dual Springs for high performanceapplications on the “B” Series Cylinder Head, you must alsoinstall our special Hand-Seat Locaters and Titanium Retainersas the Stock units are not machined to accept the inner spring. Use Stock Valve Locks with both 12500 and 12600 kits.
KIT COMPONENTSKit (16) (16) (16)Part Valve Outer Inner Seat Open Titanium Spring Coil *MaxNo. Springs OD/ID OD/ID Press. Press. Retainers Locaters Bind Lift
406-S 1.105” --- 50 lbs 125 lbs --- --- .750” .400” (Single) .815” @1.400” @1.000”12500 3205 1.105” .815” 54 lbs 160 lbs 118-TI 118-VSL .720” *.480” *(Dual) street .815” .630” @1.400” @.950”12600 3305 1.105” .815” 70 lbs 204 lbs 118-TI 118-VSL .720” *.500” *(Dual) race .815” .610” @1.400” @.950”*Warning: any valve lift over .440” will require machining down the valvve guide to prevent retainer to valve seal interference.
Weight Comparison (grams) Stock Retainers 14.3 Isky 118-TI (titanium) 7.0
VALVE SPRING KITSVALVE SPRING KITS
D16Z & Y SOHC VTECD16Z & Y SOHC VTEC
The “D” Series VTEC kit consists of Single Harmonic DampeningValve Springs and Titanium Retainers. In most cases, the stocksteel retainer is adequate, as it only weighs 6.4 grams. However,for those who want maximum weight reduction, Isky 117-TI Titanium Retainers weigh only 4.2 grams. The 506-S Single Valve Spring is great for all around performance.
No machining required for installation.
KIT COMPONENTSKit (16) (16) Part Valve O.D. Seat Open Titanium Coil MaxNo. Springs I.D. Press. Press. Retainers Bind Lift
12400 506-S .889” 60 lbs 165 lbs 117-TI 1.395” .450” .605” @1.950” @1.500”
Note: retain stock intake and exhaust locaters and valve locks.
37
Outer Inner Seat Open Rate Coil Max. Type ofPart No. Style OD/ID OD/ID Pressure Pressure Per Inch Bind Net Lift Cam
6105-SP Dual w/ 1.440” .985” 145 lbs 365 lbs 360 1.060” .625” Hyd. Roller Damper 1.083” .730” @1.800” @1.175” Solid8005-SP Dual w/ 1.530” 1.005” 150 lbs 435 lbs 415 1.160” .650” Solid Damper 1.110” .730” @1.875” @1.225”
8205-SP Dual w/ 1.530" 1.005" 150 Lbs 440 Lbs 440 1.150" .650" Solid Damper 1.110" .730" @1.900" @1.300"
9365-SP Dual w/ 1.550" 1.025" 225 Lbs 550 Lbs 460 1.170" .680" Roller Damper 1.135" .740" @1.950" @1.270"
SPECIAL PROCESSING “SP” SERIES HIGH ENDURANCE Valve Springs
Endurance PlusTM SERIES EXTREME HIGH ENDURANCE Valve Springs
The “SP” series utilizes “Hi-Tensile” Chrome Silicon outer spring material.For applications with radical cams and/or moderately high rpm, where traditional chromesilicon springs prove inadequate, the “SP” series is the next highest level of endurance.All “SP” series springs are Spintron Test-Proven up to 8000 rpm for 700 racing miles.
Every Part No. Test-Proven
700Racing Miles (every batch)
High Endurance™ “SP” Springs
are wound from “Super Clean”
Hi-Tensile Chrome Silicone Wire!
SPSeries
Every Part No. Test-Proven
850Racing Miles (every batch)
Endurance Plus™ Springs feature a
Higher Alloy Outer Spring “Plus” sp
ecial
processing for increased durability
!
“PLUS”Series Outer Inner Seat Open Rate Coil Max. Type of
Part No. Style OD/ID OD/ID Pressure Pressure Per Inch Bind Net Lift Cam
8005 PLUS Dual w/ 1.530" 1.005" 140 Lbs 400 Lbs 420 1.160" .650" Solid Damper 1.110" .730" @1.875" @1.275"
8205 PLUS Dual w/ 1.530" 1.005" 150 Lbs 420 Lbs 440 1.120" .650" Solid Damper 1.110" .730" @1.900" @1.300"
9005 PLUS Dual w/ 1.530" 1.005" 170 Lbs 455 Lbs 455 1.160" .650" Solid Damper 1.110" .725" @1.900" @1.300"
9315 PLUS Dual w/ 1.550” 1.025” 220 Lbs 530 Lbs 480 1.130 .660” Roller Damper 1.135” .740” @1.900” @1.240”
9365 PLUS Dual w/ 1.560" 1.040" 235 Lbs 560 Lbs 470 1.170" .680" Roller Damper 1.145" .740" @1.950" @1.270"
9375 PLUS Dual w/ 1.560" 1.040" 230 Lbs 560 Lbs 480 1.190" .680" Roller Damper 1.145" .740" @1.970" @1.290"
9375/85 Dual w/ 1.560" 1.040" 250 Lbs 580 Lbs 470 1.190" .680" Roller PLUS Damper 1.145" .740" @1.970" @1.290"
9385 PLUS Dual w/ 1.560" 1.040" 245 Lbs 600 Lbs 500 1.180" .720" Roller Damper 1.145" .740" @2.000" @1.280"
The Endurance Plus™ series of valve springs utilizes a specially processed Tool RoomMaterial outer spring for increased endurance/reliability beyond the “SP” series. EndurancePlus™ springs are designed for late models, modifieds, etc., and are Spintron Test-Provenup to 8400 rpm for 850 racing miles.
Full-Spectrum Harmonic Vibration ControlTMtechnologically advanced designs suppress surge and avoid harmonic convergence.
100% “Hands-On” Precision Manufactured...by master valve spring craftsmen. Our standards are the highest in the performance industry!
Absolute Maximum EnduranceTMExclusive trade-secret endurance processing delivers “near zero” pressure drop after 1,000 racing test miles!
The 1,000 Racing Mile Endurance Test StandardTMEach set is guaranteed “race ready” because we test-prove every part number, every batch!
Gold Stripe Test CertificationTool Room springsTM earn their “Gold Stripes” and written certification only after two full sets go the distance!
Exclusive Performance GuaranteeIf you are not completely satisfied that our 9900 Series Tool RoomTM springs are the most durable, fatigue re-sistant valve springs you have ever tried, return them to Isky for a full refund!
Only precision Tool RoomTM valve springs with the exclusive “Gold Stripe” deliverthis level of full throttle, indefatigable performance!
��
��
��
��
��
��
Isky TOOL ROOM™ Valve Springs are the ultimate for Winston Cup, Busch, Super Truck,WoO, Hav-a-Tampa series, and other 9:1 or all-out high compression oval track engines.
R U N“ONE OF THETHOUSAND”
For your nexthigh
performanceracing engine,
insist on the NEW“Gold Standard”.
ISKY TOOL ROOM™
quality Oval Track Racing Valve
Springs!
1,000 racing miles proven.
EveryPart Number! Every Batch!
Outer Inner Seat Open Rate Coil Max. Type ofPart No. Style OD/ID OD/ID Pressure Pressure Per Inch Bind Net Lift Cam
295-D Single w/ 1.260” — 135 Lbs 350 Lbs 360 1.100” .600” Solid Damper .886” @1.775” @1.175” 9905 Dual w/ 1.534" 1.010" 165 Lbs 450 Lbs 475 1.160" .600" Solid Damper 1.120" .740" @1.900" @1.300" 9915 Dual w/ 1.560" 1.040" 195 Lbs 540 Lbs 500 1.175" .700" Roller Damper 1.145" .740" @1.975" @1.275" 9925 Dual w/ 1.534" 1.010" 170 Lbs 450 Lbs 470 1.160" .600" Solid Damper 1.120" .740" @1.950" @1.350" 9935 Dual 1.560" 1.153" 245 Lbs. 590 Lbs. 490 1.150" .700" Roller Damperless 1.155" .820" @1.950" @1.250" 9945 Dual w/ 1.625" 1.065" 250 Lbs. 675 Lbs. 550 1.180" .750" Roller Damper 1.175" .770" @2.020" @1.270" 9955 Dual w/ 1.625" 1.065" 265 Lbs. 700 Lbs. 545 1.240" .800" Roller Damper 1.175" .770" @2.120" @1.320" 9965 Dual w/ 1.560" 1.040" 245 Lbs. 585 Lbs. 470 1.170" .680" Roller Damper 1.145" .740" @1.950" @1.270" 9975 Dual w/ 1.560" 1.040" 245 Lbs. 585 Lbs. 480 1.190" .680" Roller Damper 1.145" .740" @1.970" @1.290" 9985 Dual w/ 1.560" 1.040" 245 Lbs. 600 Lbs. 500 1.200" .700" Roller Damper 1.145" .740" @2.000" @1.300" 9995 Dual w/ 1.570" 1.035" 250 Lbs. 625 Lbs. 510 1.200" .730" Roller Damper 1.145" .740" @2.030" @1.300"
ISKY’S 1,000 RACING MILE ENDURANCE TEST STANDARDISKY’S 1,000 RACING MILE ENDURANCE TEST STANDARD
Tool Room™ Racing Valve Springs Specifications
Theoretically, it’s possible for almost anyone to make a good valve spring once. Even with rather “loose” manufacturing and quality control standards, they can simply be lucky. They may even do it again some day.But, there is only one way to do it right every time. You must of course begin with the finest valve spring wire obtainable, wind it precisely on modern equipment and employ the special processing techniques necessary for maximum load retention. Even this however, is not enough, because valve springs that are routinely manufactured this way can and do experience failures (Just Ask Our Competition). The only way to be absolutely certain every batch of endurance racing valve springs is “worthy” is to test them. Not just any test mindyou. (One company we know of feels that five or ten minutes of “prototype” testing at RPM is adequate)! This is an endurance test? Of course not and those who pretend to be endurance testing while performing such “phantom” tests are guilty of deceiving the racing community.
Rather than meaningless tests such as these, a real measure of stamina would be an endurance test of longduration under actual engine/race track operating conditions. Our 1,000 Racing Mile Endurance Test Standardis such a test, the first and only one of its kind in the industry. A test where only the best earn their stripes. GOLDSTRIPES. The Precision 9900 Series “Gold Stripe” Tool Room™ Racing Valve Springs by Isky. They’re the world’sonly endurance test-certified racing valve springs, guaranteed “One of the Thousand,” alumni of the grueling 1,000 mile Spintron® endurance test, where two complete sets are run with a zero failure tolerance. Nobreakage and no excessive load loss are permitted, because it’s pass or fail for Tool Room™ Springs - there isno gray area in between. If they don’t measure up, we don’t sell them—period! We test every batch of every partnumber we produce. We have to because you’re depending on us to deliver the absolute maximum endurancepossible in a racing valve spring. And we do. In a word, Tool Room™ valve springs are indefatigable! That’s whywe refer to them as The World’s Finest Racing Valve Springs™—because without any doubt whatsoever, theymost certainly are!
(How Tool Room™ Springs earn their “Gold” Stripes)(How Tool Room™ Springs earn their “Gold” Stripes)
Tool Room™ Valve Springs; the Crown Jewels of Isky’s Endurance 9000™ family of racing valve springs.Tool Room™ Valve Springs; the Crown Jewels of Isky’s Endurance 9000™ family of racing valve springs.
Tool Room™ Racing Valve Springs Specifications
� � � � �� � � � �
R U N“ONE OF THETHOUSAND”
40
You're almost there. The end of a tough race isfast approaching, but to win, you'll need to pushyour engine to the limit. The tach will read closeto 9000 RPM. Such sustained red-line abuseis like sudden death overtime for your valvetrain. Ordinary rollerva lve spr ings w i l l quickly succumb to resonant vibration, putting you out of therace. Only one valvespring can go there andcome back alive, everytime!
Introducing Isky's newRAD-9000™ processoption for Tool Room™
valve springs. Undertrade secret Radial-Densification™ (RAD), thephysical properties ofTool Room™ springs areoptimized for evengreater surface to coreuniformity. To insurethey'll withstand the tortures of sustained
high rpm operation, we subject each batch to the most rigorous real world test standard ever created,
SPINTRON-TEST II. It'sa no holds barred run as high as 9000 RPMwhere for over 1,000miles, race ending competitive abuse iscontinuously revisited.This pass or fail benchmark is the onlytest of its kind in the performance industryand every set of Tool Room™ springs conforms to its highstandard.
So why take a chance on anythingelse? Run the only racing valve springs w i t h s u s t a i n e d red-line protection.RAD-9000 ™ process Too l Room ™ va lvesprings from Isky. Absolutely the world'sfinest, and the newstandard of excellence inendurance racing today!
9945 RAD Dual w/ 1.625" 1.065" 250 Lbs. 675 Lbs. 550 1.180" .750" Damper 1.175" .770" @2.020" @1.270"
9955 RAD Dual w/ 1.625" 1.065" 265 Lbs. 700 Lbs. 545 1.240" .800" Damper 1.175" .770" @2.120" @1.320"
9965 RAD Dual w/ 1.560" 1.040" 245 Lbs. 590 Lbs. 475 1.170" .680" Damper 1.145" .740" @1.950" @1.270"
9968 RAD Dual w/ 1.570" 1.040" 250 Lbs. 665 Lbs. 560 1.100" .750" Damper 1.145" .745" @1.950" @1.200"
9975 RAD Dual w/ 1.560" 1.040" 245 Lbs. 590 Lbs. 485 1.190" .680" Damper 1.145" .740" @1.970" @1.290"
9985 RAD Dual w/ 1.560" 1.040" 245 Lbs. 600 Lbs. 500 1.200" .700" Damper 1.145" .740" @2.000" @1.300"
9988 RAD Dual w/ 1.570" 1.040" 250 Lbs. 660 Lbs. 550 1.150" .750" Damper 1.145" .745" @2.000" @1.250"
9989 RAD Dual w/ 1.570" 1.040" 270 Lbs. 710 Lbs. 570 1.130" .800" Damper 1.145" .745" @2.000" @1.200"
9995 RAD Dual w/ 1.570" 1.035" 250 Lbs. 625 Lbs. 510 1.200" .730" Damper 1.145" .740" @2.030" @1.300"
9998 RAD Dual w/ 1.600" 1.040" 250 Lbs. 735 Lbs. 600 1.160" .800" Damper 1.150" .745" @2.050" @1.250"
9999 RAD Dual w/ 1.600" 1.040" 250 Lbs. 770 Lbs. 650 1.150" .800" Damper 1.150" .745" @2.000" @1.200"
RAD-9000™ technology is available for the following TOOL ROOM™ valve springs.
RAD-9000™ TOOL ROOM™ valve springs are a higher performance optionand feature premium pricing.
Test Proven: Every Part No.,Every Batch, Every Time!
Outer Inner Seat Open Coil MaxPart No. Style OD/ID OD/ID Press. Press. Rate Bind Lift
Endurance Process ingRAD-9000™
NEW! �
Higher Frequency: Finely Tuned For Higher RPM, Valve Lifts & Rocker Ratios.�
41
VALVE SPRING HIGHLIGHTS
We are proud to announce that Isky has recently been appointed a Distributor forPSI Sportsman Drag Race Valve Springs.You can trust PSI (Performance Springs Inc.) Valve Springs to out-perform all others because they are exclusively 100% American Made using the finest materials, the best CNC Equipment and state of the art trade secret processing.Don’t settle for those foreign made springs of lesser quality. Insist on Genuine PSIDrag Race Valve Springs and get into the winners circle!Isky Stocks the following PSI Part numbers.Note: 1200 Series Springs utilize special Heat Treating and additional “Special Processing” for minimal load loss.
Rate Max Coil Part # Type O.D. Outer Middle Inner Seat Pressure Open Pressure Per Net Bind Inch Lift
1224 Dual 1.625” 1.175” N/A .855” 275 LBS. @ 2.000” 750 LBS @ 1.200” 594 .800” 1.130”
1246 Triple 1.645” 1.195” .870” .630” 300 LBS. @ 2.000” 890 LBS. @ 1.200” 738 .800” 1.100”
1247 Triple 1.660” 1.195” .870” .630” 340 LBS. @ 2.070” 940 LBS. @ 1.270” 750 .800” 1.130”
1248 Triple 1.660” 1.195” .870” .630” 375 LBS. @ 2.100” 1045 LBS. @ 1.200” 744 .900” 1.130”
1249 Triple 1.660” 1.195” .870” .630” 385 LBS. @ 2.200” 1110 LBS. @ 1.200” 725 1.000” 1.130”
1250 Triple 1.660” 1.195” .870 .630” 395 LBS. @ 2.250 1178 LBS. @ 1.200” 746 1.050” 1.130”
Valve Springs Specifications
(Tolerance = +/- .005) Load Tolerance = +/- 3%
I.D.
Introducing the NEW ML “MAX-LIFE” Super EnduranceRoller Valve Spring Series
Designed for use in the most grueling, sustained Hi-RPM oval track environments, the “MAX-LIFE”super endurance series are manufactured from a revolutionary new alloy steel. They employ precisionnitride heat treating and a multi-stage, micro-polished “MAX-LIFE” surface finish to enhance theirlongevity in the most aggressive endurance racing applications.
Outer Inner Seat Open Rate Coil Max.Part No. Style OD/ID OD/ID Pressure Pressure Per Inch Bind Net Lift
1577DML Dual w/ 1.550” .985” 295 lbs 860 lbs 706 1.150” .800” Damper 1.100 .706” @2.000” @1.200”9996RADML Dual w/ 1.600” 1.040” 275 lbs 810 lbs 625 1.150” .850” Damper 1.150” .745” @2.050” @1.200”
42
CHROME MOLY STEEL RETAINERSIsky 4130 Chrome Moly Light-Weight Steel Valve Sping Retainers are ideal for streetand highly-stressed competition applications.They are specially heat treated and black oxide finished to protect against corrosion.Set of 16-4130 Chromemoly steel retainers.Consult Page 32 for Installed Height Info.
LIGHTWEIGHT STEEL RETAINERSMachined from E-4340 Aircraft Quality Steel, ISKY Lightweight Steel Retainers are designed to withstand the “chafing” normally associated with Damper Valve Springs. They are typically 4-5 grams heavier than Titanium Retainers. Sold in sets of (16).
VALVE ISKY STD. SUPER-7RETAINER STEM ISKY SPRING INNER STEP DIA (I) 7O VALVE 7O VALVEPART NO. SIZE APPLICATION OUTER STEP DIA (O) LOCK NO. LOCK NO.327-ST 5/16 455/456, VW Rabbit SOHC .665 (I) N/A N/A V-005-D, 411 VW/Porsche 914 .920 (O) 625/626, Volvo B-16 & B-20 4 Cyl.4107-ST 5/16 5005, 6005, 6105, 6205, .725 (I) VL-5/16 N/A 8005-A, 8305, 9005, 9105, 9265 1.060 (O)507-ST 11/32 5005, 6005, 6105, 6205 .735 (I) VL-32 N/A 8005-A, 8305, 9005, 9105, 9265 1.080 (O)507-STA 11/32 5005, 6005, 6105, 6205 .735 (I) VL-32 N/A.060 HIGHER INST. HGT. THAN 507-ST 8005-A, 8205, 8305, 9005, 9105, 9265 1.080 (O)527-STA 11/32 9205, 9315, 9365 .730 (I) VL-32 N/A 1.120 (O)607-STA 11/32 6005, 8005-A (351 CLEVELAND .730 (I) N/A N/A V-8 WITH ROTATING VALVES) 1.060 (O)707-ST 11/32 4005, 4205, 205-D .886 (O) VL-32 N/A707-STA 11/32 235-D, 295-D .886 (O) VL-32 N/A927-ST 11/32 5005 -- PONTIAC V-8 ONLY .710 (I) VL-32 N/A 1.065 (O)347-ST 3/8 5005, 6005, 6105, 6205 .735 (I) VL-3/8 N/A 8005-A, 8305, 9005, 9105, 9265 1.080 (O)627-ST 3/8 625/626 .670 (I) N/A N/A (EARLY BUICK V-6 & V-8 ONLY) .895 (O)3607-ST 3/8 5005, 6005, 6105, 6205 .730 (I) VL-3/8 N/A.060 HIGHER INST. HGT. THAN 347-ST 8005-A, 8205, 8305, 9005, 9105, 9265 1.065 (O)175-ST ALL 8005-A, 8205, 8305 .725 (I) N/A VL-600, VL-700, VL-800 9005, 9265 1.105 (O) 5/16 11/32 3/8275-ST ALL 9205, 9275, 9315, 9365, 9365-SP .730 (I) N/A VL-600, VL-700, VL-800 9375/85 PLUS, 9385, 9425, 9905 1.120 (O) 5/16 11/32 3/8 9915, 9925, 9965, 9975, 9985, 9995375-ST ALL 9685, 9705, 9945 .765 (I) N/A VL-600, VL-700, VL-800 1.165 (O) 5/16 11/32 3/8*200-ST/10 DEG ALL 8005-A,8205,8305,9005,9205,9265,9275 .725 (I) N/A *VL-10-5/16,*VL-10-11/32,*VL-10-3/8 9315,9365,9365-SP,9375/85 PLUS,9385 1.115 (O) 5/16 11/32 3/8 9425,9905,9915,9925,9965,9975,9985,9995*300-ST/10 DEG ALL 9685, 9705, 9945 .765 (I) N/A *VL-10-5/16,*VL-10-11/32,*VL-10-3/8 1.165 (O) 5/16 11/32 3/8
* 10 DEGREE VALVE LOCKS
Isky First
VALVE SUPER 7-DEG. 10 DEG. RETAINER STEM GRAM INNER STEP DIA (I) VALVE LOCK VALVE LOCK PART NO. SIZE WEIGHT OUTER STEP DIA (0) PART NO. PART NO.
90-ST/10 DEG ALL 22.4 .725” N/A VL-10-5/16 VL-10-11/32 VL-10-3/8 1.110” 5/16 11/32 3/8
92-ST ALL 23.7 .745” VL-600 VL-700 VL-800 N/A 1.140” 5/16 11/32 3/8
92-ST/10 DEG ALL 23.7 .745” N/A VL-10-5/16 VL-10-11/32 VL-10-3/8 1.140” 5/16 11/32 3/8
975-ST ALL 26.3 .765” VL-600 VL-700 VL-800 N/A 1.165” 5/16 11/32 3/8
97-ST/10 DEG ALL 27.3 .765” N/A VL-10-5/16 VL-10-11/32 VL-10-3/8 1.165” 5/16 11/32 3/8
43
TITANIUM RETAINERS
VALVE ISKY STD. SUPER-7RETAINER STEM ISKY SPRING INNER STEP DIA (I) 7O VALVE 7O VALVEPART NO. SIZE APPLICATION OUTER STEP DIA (O) LOCK NO. LOCK NO.
50-Ti 5/16 5005, 5105 .725 (I) VL-5/16 N/A 6005, 6105, 6205 1.060 (O)
57-Ti 5/16 235-D, 295-D .886 (O) VL-500 (Bead lock on late model LS-1 Small Block Chevy V8)
60-Ti 11/32 5005, 5105 .735 (I) VL-32 N/A 6005, 6105, 6205 1.080 (O)
70-Ti 3/8 5005, 5105 .730 (I) VL-3/8 N/A 6005, 6105, 6205 1.065 (O)
91-Ti ALL 8005-A, 8205, 8305, 9005, 9205, 9265, .720 (I) N/A VL-600, VL-700, VL-800 9275, 9315, 9365, 9365-SP 1.110 (O) 5/16 11/32 3/8 9375/85 PLUS, 9385, 9425, 9905, 9925
92-Ti ALL 9915, 9965, 9975, 9985, 9995 .740 (I) N/A VL-600, VL-700, VL-800 + All RAD & 1600 Series versions of above 1.140 (O) 5/16 11/32 3/8
94-Ti ALL 9935 .820 (I) N/A VL-600, VL-700, VL-800 1.145 (O) 5/16 11/32 3/8
975-Ti ALL 9685, 9705, 9945, 9955 .765 (I) N/A VL-600, VL-700, VL-800 9945 RAD, 9955 RAD 1.165 (O) 5/16 11/32 3/8
*90-Ti/10 DEG ALL 8005-A,8205,8305,9005,9205,9265,9275 .725 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 9315,9365,9365-SP,9375/85 PLUS,9385 1.115 (O) 5/16 11/32 3/8 9425,9905,9915,9925
*92-Ti/10 DEG ALL 9915, 9965, 9975, 9985, 9995 .740 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 + All RAD & 1600 Series versions of above 1.140 (O) 5/16 11/32 3/8
*94-Ti/10 DEG ALL 9935 .820 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 1.145 (O) 5/16 11/32 3/8
*95-Ti/10 DEG ALL 1224 PSI .850 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 1.170 (O) 5/16 11/32 3/8
*97-Ti/10 DEG ALL 9685, 9705, 9945, 9955 .765 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 9945 RAD, 9955 RAD 1.165 (O) 5/16 11/32 3/8
*980-Ti/10 DEG ALL 9701, 9801-A, 9901-A .640 (I) N/A *VL-10-5/16, *VL-10-11/32, *VL-10-3/8 1246, 1247, 1248, 1249, 1250 PSI .880 (M) 5/16 11/32 3/8 1.195 (O)
ISKY TITANIUM RETAINERS ARE 20-40% STRONGER than all other retainers. They are made from specially heattreated 100% aircraft quality bar stock material.
* 10 DEGREE VALVE LOCKS
44
ONE PIECE 5/16 DIAMETER PUSHRODS
All Isky One-Piece 5/16” Diameter Pushrods are manufactured from the finest available grade of Seamless .095” Wall, Chrome Moly Tubing; specially Heat Treated. All ends are Precision Formed in a Turning Center (Not Swedged) to assure you the most reliable andstrongest 5/16” Diameter Pushrods in the Automotive Racing Industry!
Part No. Application Overall Length Part No. Application Overall Length
1235-L Minus .400 Small Block Chevy V-8 6.100” 393-B-HG Ford Boss 302 V-8 7.562”1235-L Minus .350 Small Block Chevy V-8 6.150” 203-HG Minus .180 Pontiac 4-Cyl 7.600”1235-L Minus .300 Small Block Chevy V-8 6.200” 203-HG Minus .150 Small Block Chevy V-8 7.631”1235-L Minus .250 Small Block Chevy V-8 6.250” 203-HG Minus .100 Small Block Chevy V-8 7.681”203-RM-HG Small Block Chevy V-8 6.281” 203-HG Minus .050 Small Block Chevy V-8 7.731”1235-L Minus .200 Small Block Chevy V-8 6.300” 203-HG Small Block Chevy V-8 7.781”1235-L Minus .150 Small Block Chevy V-8 6.350” 203-HG + .050 Small Block Chevy V-8 7.831”1235-L Minus .100 Small Block Chevy V-8 6.400” 203-HG + .100 Small Block Chevy V-8 7.881”1235-L Minus .050 Small Block Chevy V-8 6.450” 203-HG + .160 Small Block Chevy V-8 7.941”1235-L Small Block Chevy V-8 6.500” 203-HG + .200 Small Block Chevy V-8 7.981”1235-L + .050 Small Block Chevy V-8 6.550” 203-HG + .250 Small Block Chevy V-8 8.031”1235-L + .100 Small Block Chevy V-8 6.600” 203-HG + .300 Small Block Chevy V-8 8.081”1235-L + .160 Small Block Chevy V-8 6.660” 683-A-HG Ford 351 Windsor V-8 8.125”1235-L + .200 Small Block Chevy V-8 6.700” 203-HG + .350 Small Block Chevy V-8 8.131”1235-L + .250 Small Block Chevy V-8 6.750” 203-HG + .400 Small Block Chevy V-8 8.181”393-SLHG Ford 289-302 V-8 6.812” 203-HG + .450 Small Block Chevy V-8 8.231”393-HG Ford 289-302 V-8 6.875” 393-A-HG Ford 351 Windsor V-8 8.250”1235-L + .400 Small Block Chevy V-8 6.900” 203-HG + .500 Small Block Chevy V-8 8.281”1235-L + .450 Small Block Chevy V-8 6.950” 203-HG + .550 Small Block Chevy V-8 8.331”1235-L + .500 Small Block Chevy V-8 7.000” 203-HG + .600 Small Block Chevy V-8 8.381”1235-L + .550 Small Block Chevy V-8 7.050” 203-HG + .650 Small Block Chevy V-8 8.431”1235-L + .600 Small Block Chevy V-8 7.100” 393-C-HG Ford Boss 351 V-8 8.470”1235-L + .650 Small Block Chevy V-8 7.150” 383-C-HG Ford 429-460 V-8 8.671”203-HG Minus .580 Small Block Chevy V-8 7.200” 923-HG Pontiac V-8 9.125”203-HG Minus .460 Small Block Chevy V-8 7.320” 233-HG + .125 Chevy II 4 & 6 Cyl 9.812”203-HG Minus .380 LS-1 Chevy V-8 7.400”
All the above listed pushrods are compatible with Pushrod Guide Plates.
SPECIAL NOTE:We now have available a limited supply of each of the following special length one-piece .095” wall pushrods for a slightly higher pricethan our normal production length one-piece pushrods.7.425”, 7.450”, 7.500”, 8.560”, 8.610” and 9.250”Contact Factory for current pricing.
45
Tube Oil Isky Length Non Hyd. Solid Roller Cup & Ball & Part No. Description Size Hole Int. Ext. Adj. Adj. Lifter Lifter Lifter Ball Ball
5/16
5/16
3/8
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
3/8
7/16
3/8
3/8
7/16
3/8
5/16
5/165/16
3/8
3/8
3/85/16
3/8
3/85/16
5/16
5/16
5/16
5/16
5/16
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
NoYes
No
No
NoYes
No
NoYes
Yes
Yes
Yes
Yes
Yes
7.781
7.781
7.781
7.881
7.941
7.981
8.031
7.681
7.320
7.200
6.281
8.281
8.281
8.687
7.650
8.687
8.796
9.687
11.25011.377
8.187
7.312
8.31210.109
9.343
9.2188.671
6.875
6.875
8.250
8.250
7.562
7.781
7.781
7.781
7.881
7.941
7.981
8.031
7.681
7.320
7.200
6.281
9.250
9.250
9.656
8.600
9.656
9.125
9.687
11.25011.377
8.187
7.312
8.31210.109
9.343
9.2188.671
6.875
6.875
8.250
8.250
7.562
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
ISKY CHROME MOLY TUBULAR PUSHRODS
Iskenderian Method of Measuring PushrodsThe proper method of measuring the length of pushrods is to include the theoretical overall length, however, this is difficult for the average individual since special equipment is required. In the interest of accuracy and to avoid confusion, we have adopted the above methodof measurement. This eliminates the difficulties that arise when makingmeasurements in the field, or when instaling special length pushrods(custom made) on special order for our customers.)
*All Pushrod part numbers with an asterik (*) are not usually carried in inventory and should be considered special order items.
203
203-HG
203-HG3/8
203-HG+ 100”
203-HG+ .160”203-HG+ .200”203-HG+ .250”203-HG- .100”
203-HG-.460
203-HG-.580
203RMHG
203-963/8
203-967/16
203-96TB3/8
203-96-.650
203-96TB7/16
223
233
273B293
303
303A
303B333
383
*383-B383C-HG
393
393-HG
393-A
393-A-HG
393-BHG
Chevrolet 55 and up, 265’ TO 400” Stock Adj. Rocker, Stock orIsky LifterChevrolet 55 and up, 265” to 400”, Stock or Isky Solid Lifter,Heat Treated for Guide Plate HeadsChevrolet 55 and up, 265” to 400” Stock Adj. Rocker, Stock orIsky Lifter Heat Treated for 3/8 Guide PlatesChevrolet 55 and up, 265” to 400” Stock or Isky Solid/Hyd.LifterHeat Treated for Guide Plate HeadsChevrolet 55 and up, 265” to 400”, Stock or Isky Solid/Hyd.Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock or Isky Solid/Hyd.Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock or Isky Solid/Hyd.Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock or Isky Solid/Hyd.Lifter, Heat Treated for Guide Plates, Jessel RockerChevrolet 55 and up, 265” to 400”. Stock Adj. Rocker, 2020-HYRT Retrofit Hyd. Roller Lifter. Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”. Stock Adj. Rocker, 2070-HYRT Isky Retrofit “Anti Pump Up” Hyd. Roller Lifter. HeatTreated for Guide Plates.Chevrolet 55 and up, 265” to 400” .160 Short, Isky #252 RollerHeat Treated for Guide Plate HeadsChevrolet 65 and up, 396” to 454” H.T., Guide Plates, StockAdj. Rocker, Stock or Isky LifterChevrolet 65 and up, 396” to 454”Stock Adj. Rocker, Stock or Isky Lifter Heat Treated for GuidePlatesChevrolet 65 and up, 366 Truck BlockStock Adj. Rocker, Stock or Isky Lifter Heat Treated for GuidePlatesChevrolet 65 and up, 396” to 454”. Stock Adj. Rocker, 3970-HYRT Isky Retrofit “Anti Pump Up” Hyd. Roller Lifter. HeatTreated for Guide PlatesChevrolet 65 and up, 366 Truck BlockStock Adj. Rocker, Stock or Isky Lifter Heat Treated for GuidePlatesChevrolet 61 to 65, 409” to 427”Stock Adj. Rocker, Stock or Isky LifterChevrolet II 4 & 6 Cyl. 63 & up, 153” to 250”Stock Adj. Rocker, Stock or Isky LifterChevrolet 6 Cyl. 37 to 62, 216” to 261”. Stock Adj. RockerChevrolet 292” Truck, 63 and upStock Adj. Rocker, Stock or Isky LifterFord/Merc. 54 to 62, 239” to 312”Stock Adj. Rocker, Stock or Isky LifterFord 68 and up, 170” and 200”Stock Non Adj. Rocker, Isky Hyd LifterFord 69 and up, 250”. Stock Non Adj. Rocker, Isky Hyd. LifterFord 6 Cyl. 65 and up, 240” to 300”Stock Adj. Rocker, Stock or Isky LifterFord 58 to 72, 332” to 428” Stock Adj. Rocker,Isky #384 Adj. Rocker, Isky LifterFord 58 to 72, 332” to 428”. Gotha Adj. Rocker, Isky LifterFord 68 and up, 429 WedgeStock Adj. Rocker, Stock or Isky Lifter, Heat TreatedFairlane 62 and up, 221” to 302”, Stock Adj. rocker,Isky LifterFairlane 62 and up, 221” to 302”, Stock Adj. Rocker, Isky LifterHeat Treated for Guide PlatesFairlane 351 Windsor, 68 to 72, Isky LifterStock Adj. rocker. This also fits Olds 350-68 and upFairlane 351 Windsor, 68 to 72, Isky Lifter, Stock Adj.Rocker. This also fits Olds 350-68 and up, Heat Treated forGuide PlatesFord Boss 302, 69 and up, Isky Lifter Stock Adj. Rocker,Heat Treated for Guide Plate Heads
46
Tube Oil Isky Length Non Hyd. Solid Roller Cup & Ball & Part No. Description Size Hole Int. Ext. Adj. Adj. Lifter Lifter Lifter Ball Ball
393-CHG
393DA393-SL
393-SLHG
403-A
453
*503-A
*523*533*543-A*553
*603-A*613623-F
*633-A643
*653653-A663-A663-B
*673683-A
683-A-HG
683-B
683-C
693-A
693-B
*703-A*803-L
903913
923-HG
*1003*1013*10231033
1033-A
*10431053
*1053-A*1063*1073*10931103
*1113*11231133
*11631193-A
1193-B
Ford 351 Cleveland, Heat Treated for Guide Plate heads,Stock Adj. rocker, Stock or Isky LifterFord 351 Cleveland, Stock Rocker, Isky Hyd LifterFord 62 and up, 221 to 302WStock Adj. Rocker, Stock Solid LifterFord 62 and up, 221 to 302W, Stock Adj. Rocker, StockSolid Lifter, Heat Treated for Guide PlatesFord Cleveland 400 & 351M EnginesStock Rocker, Stock or Isky LifterPinto 1600cc and Cortina 1600cc, Cross Flow HeadDesign, Stock Adj. Rocker, Stock or Isky LifterOlds 49 to 56, 303-324”Stock Non Adj. rocker, Isky solid LifterOlds 49-51, 303”, Stock Non Adj. Rocker, Isky Hyd. LifterOlds 52-55, 324”, Stock Non Adj. rocker, Isky Hyd. LifterOlds 49-56, 303”-324” Stock Non Adj. Rocker, Isky RollerOlds 56-58, 324”-370”Stock Non Adj. Rocker, Isky Hyd. LifterOlds 57-58, 370” Stock Non Adj. Rocker, Isky Solid LifterOlds 59-64, 394” Stock Non Adj. Rocker, Isky Hyd. LifterOlds F85 215 Aluminum, 61-63Stock Non Adj. rocker, Isky Solid LifterOlds 57-58, 370”, Stock Non Adj. Rocker, Isky LifterOlds F85-215” Aluminum, 61-63Stock Non Adj. rocker, Isky Hyd. LifterOlds 59 to 64, 394”, gotha Adj. Rocker, Isky LifterOlds 59/64, 394” Stock Non Adj. Rocker, Isky LifterOlds 64 & up, 330”-350”, Stock Non Adj. Rocker, isky LifterOlds 65 and up, 400” to 455”Stock Non Adj. Rocker, Isky LifterOlds 59 to 64, 394”, Gotha Adj. Rocker, Isky LifterOlds 64 to 67, 330” Stock Non Adj. Rocker, Isky LifterFord 351 Windsor, Stock or Isky Solid Lifter,Stock Adj. Rocker, Heat Treated for Guide PlatesOlds 65 and up, 400” to 455”Stock Non Adj. Rocker, Isky LifterOlds 66/67, 400” .921 Tappet SizeStock Non Adj. Rocker, Isky LifterOlds 64 and up, 330”-350”Stock Non Adj. Rocker, Isky LifterOlds 65 and up, 400”-455”Stock Non Adj. Rocker, Isky LifterCadillac 49 to 62, Stock Non Adj. Rocker, isky LifterPackard 55/56, Chry 300 LifterStock Non Adj. Rocker, Isky Solid LifterPontiac 55-60, Stock Adj. Rocker, Stock or Isky LifterPontiac 61-66, Stock Adj. Rocker, Stock or Isky LifterPontiac (Nascar 61-63) 67 and up 400” to 455”Heat Treated for Guide PlatesBuick 53-56, 322”, Stock Non Adj. Rocker, Isky LifterBuick 53-56, 322”, Stock Non Adj. Rocker, Isky Hyd. LifterBuick 53-56, 322”, Stock Non Adj. Rocker, Isky LifterBuick 61 to 64, 215”, AluminumStock Non Adj. Rocker, Isky Hyd. LifterBuick 64-66, 300”, Stock Non Adj. Rocker, Isky Hyd. LifterBuick 53-56, 322”, Stock Non Adj. Rocker, Isky RollerBuick 61 to 64, 215” AluminumStock Non Adj. Rocker, Isky Hyd. LifterBuick 64 to 66, 300”, Stock Non Adj. Rocker, isky LifterBuick 53 to 56, 322”, Stock Adj. Rocker, Isky RollerBuick 53 to 56, 322”, Gotha Adj. Rocker, Isky LifterBuick 53-56, 322” Stock Non Adj. Rocker, Isky Hyd. LifterBuick 57-66, 364 and 401-425Stock Non Adj. Rocker, Isky LifterBuick 57-61, 364”, Stock Non Adj. Rocker, Isky Hyd. LifterBuick 57-61, 364”, Stock Adj. Rocker, Isky LifterBuick 59 to 66, 401-425. Also Buick V6Stock Non Adj. Rocker, Isky LifterBuick 59-66, 401”-425”, Stock Adj. Rocker, Isky LifterBuick 67 to 69, 400”-430”, 340”-350”Stock Non Adj. Rocker, Isky LifterBuick 67 to 69, 400”-430”, 340”-350”Stock Non Adj. Rocker, Isky Lifter
5/16
3/85/16
5/16
3/8
5/16
5/16
5/165/165/165/16
5/165/165/16
5/165/16
5/165/165/165/16
5/165/165/16
5/16
5/16
5/16
5/16
5/163/8
5/165/165/16
5/165/165/165/16
5/165/165/16
5/165/165/165/165/16
5/165/165/16
5/165/16
5/16
Yes
YesYes
Yes
Yes
No
No
NoNoNoNo
NoNoNo
NoNo
NoNoYesYes
NoYesYes
Yes
Yes
Yes
Yes
NoNo
YesYesYes
NoNoNoNo
NoNoNo
NoNoNoNoNo
NoNoNo
NoNo
No
8.470
7.5626.812
6.812
8.562
7.750
8.500
9.0629.0936.6259.046
8.5629.2507.500
6.8128.234
9.3598.8127.3598.640
7.5318.1258.125
9.578
9.406
7.437
8.796
9.0629.718
9.1408.6719.125
7.5008.2348.0468.031
8.6256.0937.312
7.6566.7348.0937.3127.593
8.4848.2967.843
8.5319.359
8.625
8.470
7.5626.812
6.812
8.562
7.750
8.500
9.0629.0936.6259.046
8.5629.2507.500
6.8128.234
9.3598.8127.3598.640
7.5318.1258.125
9.578
9.406
7.437
8.796
9.0629.718
9.1408.6719.125
7.5008.2348.0468.031
8.6256.0937.312
7.6566.7348.0937.3127.593
8.4848.2967.843
8.5319.359
8.625
X
X
X
X
X
X
X
XXX
X
X
XX
X
XX
X
XX
X
X
X
X
X
X
XX
X
X
X
X
XXX
X
X
XXX
XXX
X
XX
XX
XX
X
X
XX
X
X
X
XX
X
X
X
XXX
XX
X
X
XX
X
X
X
X
X
X
X
X
X
XX
X
X
X
XX
XXX
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
XXXX
XXX
XX
XXX
XX
X
X
X
X
XX
XXX
XXXX
XXX
XX
XX
XXX
XX
X
47
Tube Oil Isky Length Non Hyd. Solid Roller Cup & Ball & Part No. Description Size Hole Int. Ext. Adj. Adj. Lifter Lifter Lifter Ball Ball
*1203
1235-L
1235-L- .100”1235-L+ .100”1235-L+ .160”1235-L+ .250”1235-L3/8*1283
*1303
*1313
1343-A1353
*1403-L*14131503
1523-L
1533-L
1603-L
1613
*1613-A
*1613-B
1623
*1623-A
*1623-B
1633-A
1633-B
1643-A
1643-L
1683
1693
*1703-L
*1713
*1803-L
*1813
*2103-L
*2113
*2303-L
*2313
*2403-L
*2413
*3003-L
*3013
*3023
*3033-L
Lincoln 52-57, 368”, Ford “6” 52 to 64Stock Adj. Rocker, isky LifterChevrolet 55 and up, 265” to 400”, Stock Adj. Rocker, IskyRoller Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Jessel. Rocker, Isky RollerLifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock Adj. Rocker, IskyRoller Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock Adj. Rocker, IskyRoller Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock Adj. Rocker, IskyRoller Lifter, Heat Treated for Guide PlatesChevrolet 55 and up, 265” to 400”, Stock Adj. Rocker, IskyRoller Lifter, Heat Treated for 3/8 Guide PlatesLincoln 58 to 67, 383-430-462, Stock FordAdj. Rocker, Isky #384 Adj. Rocker, Isky LifterRambler 57 to 66, 287”-327”, Stock Non Adj. Rocker,Isky 3102H LifterRambler 57 to 66, 287”-327”, Stock Non Adj. Rocker,Isky LifterAmerican Motors 304-Jeep V8American Motors 66 to 72, 290”-401”Stock Adj. Rocker, Isky Solid Lifter OnlyPlymouth 55 to 56, 270” Stock Non Adj. Rocker, Isky LifterPlymouth 55 to 56, 270” Stock Non Adj. Rocker, Isky LifterPlymouth 55-66, 277” to 318”Stock Adj. Rocker, Stock Solid or Isky LifterValiant 6 Cyl. 60 to 72, 170”Stock Adj. Rocker, Stock Solid or Isky LifterValiant 6 Cyl. 60 to 72, 225”Stock Adj. Rocker, Stock Solid or Isky LifterChrysler “B” 58 to 72, 350” to 383”,Stock Non Adj. Rocker, Isky Lifter, 3102HChrysler “B” 58 to 72, 350” to 383”,Stock Adj. Rocker, Isky Adj. Rocker, Isky Hyd. LifterChrysler “B” 58 to 67, 350” to 383”,Stock Non Adj. Rocker, Isky Hyd. LifterChrysler “B” 58 to 67, 350” to 383”,Stock Adj. Rocker, Isky Adj. Rocker, Stock Hyd. LifterChrysler “B” 59 to 72, 413-426-440,Stock Adj. Rocker, Isky Adj. Rocker, Isky Hyd. LifterChrysler “B” 59 to 67, 413-426,Stock Non Adj. Rocker, Stock Hyd. LifterChrysler “B” 58 to 67, 413-426,Stock Adj. Rocker, Isky Adj. Rocker, Stock Hyd. LifterChrysler “B” 58 to 72, 350” to 383”,Stock Adj. Rocker, Isky Adj. Rocker, Isky LifterChrysler “B” 59 to 72, 413”-440”, Stock Adj. Rocker, Isky Adj. Rocker, Stock Solid or Isky LifterDodge 62 to 67, 426”, Heat Treated, Stock Adj. Rocker,Isky Adj. Rocker, Stock Solid or Isky LifterChrysler “B” 59 to 72, 413” to 440”,Stock Non Adj. Rocker, Stock Solid or Isky LifterChrysler “B” 58 to 72, 350” to 383”,Stock Non Adj. Rocker, Isky Hyd. LifterChrysler “B” 58 to 72, 413”-440”,Stock Non Adj. Rocker, Stock Hyd. LifterDodge 56 to 58, 315” to 325”, Stock Non Adj. Rocker,Stock Solid Lifter or Isky LifterDodge 56 to 58, 315” to 325”Stock Non Adj. Rocker, Isky Hyd. LifterDodge Hemi 53-55, 241” to 270”,Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterDodge Hemi 53-55, 241” to 270”,Stock Non Adj. Rocker, Isky Hyd. LifterDodge Hemi 57 D500, 325”Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterDodge Hemi 57 D500, 325”Stock Non Adj. Rocker, Isky Hyd. LifterDeSoto Hemi 52 to 55, 341”,Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterDeSoto Hemi 52 to 55Stock Non Adj. Rocker, Isky Hyd. LifterDeSoto Hemi 56 to 57, 341”,Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterDeSoto Hemi 56 to 57, 341”,Stock Non Adj. Rocker, Isky Hyd. LifterChrysler Hemi 51 to 56, 301” to 354”Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 51 to 56, 301” to 354”Stock Non Adj. Rocker, Isky Hyd. LifterChrysler Hemi 51 to 56, 301” to 354” Stock 300Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 51 to 56, 301” to 354” Heat TreatedStock Non Adj. Rocker, Stock Solid Lifter or Isky Lifter
3/8
5/16
5/16
5/16
5/16
5/16
3/8
3/8
5/16
5/16
5/165/16
5/165/163/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
5/16
5/16
3/8
3/8
5/16
5/16
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
YesYes
NoNoNo
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
9.671
6.500
6.400
6.600
6.660
6.750
6.500
9.734
8.078
7.828
6.8128.015
7.4067.1568.578
8.296
9.953
7.890
8.250
8.593
8.375
8.984
9.328
9.125
8.578
9.265
9.375
8.625
7.593
8.421
8.375
8.171
7.640
7.468
8.750
8.515
8.062
7.796
8.812
8.531
8.906
8.640
9.750
8.906
9.671
6.500
6.400
6.600
6.660
6.750
6.500
9.734
8.078
7.828
6.8128.015
7.4067.1568.578
8.296
9.953
7.890
8.250
8.593
8.375
8.984
9.328
9.125
8.578
9.265
9.375
8.625
7.593
8.421
8.375
8.171
9.187
8.750
10.031
9.796
9.328
9.062
10.078
9.796
10.375
10.109
11.250
10.375
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
48
Tube Oil Isky Length Non Hyd. Solid Roller Cup & Ball & Part No. Description Size Hole Int. Ext. Adj. Adj. Lifter Lifter Lifter Ball Ball
3603-L
3613
3623
3633-L
3903
3913
3923
41033/841037/164613
AN-003
AN-013
AH-003
AH-013
D-003
D-013
M-003
MG-003
MG-013
RN-003
SP-003
SP-013
SB-003
TR-003
TR-013
VL-003
VL-013
VL-123
V-003
V-003B
V-003C
V-003minus .075V-003A
minus .075V-003B
minus .075V-003C
minus .075
Chrysler Hemi 57 to 58, 392”Stock Non Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 57 to 58, 392”Stock Non Adj. Rocker, Isky Hyd. LifterChrysler Hemi 57 to 58, 392”Stock 300 Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 57 to 58, 392” Heat TreatedStock Non Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler 64 to 72, 273” to 360” “A” Engine, Stockor Isky 3904 Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler 64 to 72, 273” to 360” “A” Engine, Stockor Isky 3904 Adj. Rocker, Isky Hyd. LifterChrysler 64 to 72, 273” to 360” “A” Engine,Stock Non Adj. Rocker, Isky Hyd. LifterChrysler Hemi 64 to 71, 426”, Heat Treated,Stock Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 64 to 71, 426”, Heat Treated,Stock Adj. Rocker, Stock Solid Lifter or Isky LifterChrysler Hemi 64 to 71, 426”, Heat Treated, Stock Adj. Rocker, Isky Hyd. LifterAnglia, 105E and 109e, Stock Adj.Rocker, Stock Lifter or Isky LifterAnglia, 116E & Cortina, Stock Adj.Rocker, Stock Lifter or Isky LifterAustin Healy, 6 Cyl., 3000Stock Adj. Rocker, Stock Solid LifterAustin Healy, 4 Cyl. Stock Adj. Rocker, Stock Solid LifterDatsun, 4 Cyl., 1300ccStock Adj. Rocker, Stock LifterDatsun, 4 Cyl., 1500cc to 1600ccStock Adj. Rocker, Stock LifterMG, TF-TD-TC, 4 Cyl.Stock Adj. Rocker, Stock LifterMGA-MGB, 4 Cyl. 56 to 72Stock Adj. Rocker, Stock LifterMGA-MGB, 4 Cyl. 56 to 72Stock Adj. Rocker,Sprite or Morris Minor LifterRenault, R8-R10 Engines, 4 Cyl.Stock Adj. Rocker, Stock Lifter or Isky LifterSprite-Morris Minor-Mini-Cooper -- Midget948 to 1048cc, Stock Adj. Rocker, Stock LifterSprite-Morris Minor-Mini-Cooper -- Midget1275cc, Stock Adj. Rocker, Stock LifterSunbeam Alpine, 4 Cyl. & Hillman MinStock Adj. Rocker, Stock LifterTriumph, 4 Cyl. TR-2-3-4Stock Adj. Rocker, Stock LifterTriumph Spitfire & Herald, 4 Cyl.Stock Adj. Rocker, Stock LifterVolvo, B16, 4 Cyl.Stock Adj. Rocker, Stock LifterVolvo, B18-B20, 4 Cyl.Stock Adj. Rocker, Stock LifterVolvo, B18-B20, 4 Cyl.Stock Adj. Rocker, Isky 202-H LifterVolkswagen, 1200ccStock Adj. Rocker, Isky Hyd. LifterVolkswagen, 1200ccStock Adj. Rocker, Stock Lifter or Isky LifterVolkswagen, 1300cc to 1600ccStock Adj. Rocker, Stock Lifter or Isky LifterVolkswagen, 1200ccStock Adj. Rocker, Isky Hyd. LifterVolkswagen, 1300cc to 1600ccStock Adj. Rocker, Isky Hyd. LifterVolkswagen, 1200ccStock Adj. Rocker, Stock Lifter or Isky LifterVolkswagen, 1300cc to 1600ccStock Adj. Rocker, Stock Lifter or Isky Lifter
3/8
3/8
3/8
3/8
5/16
5/16
5/16
3/8
7/16
3/8
5/16
5/16
5/16
3/8
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
3/8
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
9.390
9.093
10.234
9.390
7.531
7.265
6.625
10.828
10.828
10.546
6.656
7.328
8.218
10.062
7.140
7.687
8.546
8.703
10.656
6.812
8.437
8.703
10.312
10.062
7.812
8.328
8.015
8.737
10.187
10.671
11.078
10.112
10.675
10.596
11.000
10.859
10.562
11.734
10.859
7.531
7.265
6.625
11.765
11.765
11.484
6.656
7.328
8.218
10.062
7.140
7.687
8.546
8.703
10.656
6.812
8.437
8.703
10.312
10.062
7.812
8.328
8.015
8.737
10.187
10.671
11.078
10.112
10.675
10.596
11.000
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
49
ORIGINAL STRONGER ROLLER ROCKER ARMS
Since 1967...Using our Special Extruded Aluminum Alloy and high arch rib design, Isky Roller Rockers stillsurpass all others in Durability and Performance.Our Roller Rocker Arms have been proven by thousands of satisfied customers in Oval Track,Drag Boats, Road and Drag Racing, etc. ... across the nation and the world for over 40 years!So why take chances? Buy the BEST.
APPLICATION PART NO. COLOR RATIO STUD SIZE SMALL BLOCK CHEVY V-8 204 Black 1.5 3/8 204-716 Black 1.5 7/16 � 204-6 Red 1.6 3/8 � 204-6-716 Red 1.6 7/16 � 204-65-716 Brown 1.65 7/16 BIG BLOCK CHEVY V-8 � 204-96 Blue 1.75 7/16 � 204-96-8 Purple 1.8 7/16 BOSS 302-351 FORD V-8 204-96 Blue 1.75 7/16 � 204-96-8 Purple 1.8 7/16 429-460 WEDGE FORD V-8 204-96 Blue 1.75 7/16(WHEN USING CHEVY STYLE ROCKER STUDS) � 204-96-8 Purple 1.8 7/16
� Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
HI-STRENGTH ROCKER STUDS
1/8” Longer Threaded Top!A genuine aero-space quality product! Isky Chrome Moly Rocker Arm Studs are forged for higher strength and optimum metallurgical properties - not machined from screw stock like the competition. They also feature rolled threads and are 1/8” longer than stock Chevy studs for better Rocker-Nut Grip!
Part No. Application Set of 16
209-A* Chevy 283-350 V8 (3/8-24 top thread) + 1/8” longer than the OEM Chevy stud: provides for 3 more threads in contact with rocker arm adj. nuts219-A* Chevy 283-350 V8 (7/16-20 top thread) Heavy duty conversion Chevy 396-454 V8 (7/16-20 top thread) High performance stock replacement1309 AMC-V8 Engines (3/8-24 top thread)#210* Tool Kit (Holesaw Pilot and Bottoming Tap)
Another ISKY first, introduced to the industry in 1958. ISKY Hi-strength Screw-In Rocker Arm Studs replace stock pressed-in studs which are prone to pull-out with higher valve spring loads and valve lift during the stress of high-speed competition. Manufactured from aircraft quality 4130chrome moly steel, they featured rolled threads for better structural grain flow and fatigue resistance. Three types are available to the high-performance enthusiast.
*For Small Block Chevy V8 cyl. heads $140Deposit. $60 refundable when returned.
POLY LOCKS • Rocker Arm Adj. NutsIsky Poly Locks replace OEM crimped rocker arm adjusting nuts and eliminate the bothersome re-adjustment procedures associated with thestock components, which are prone to come loose during competition.The allen set screw threads into the large hex-nut and securely shouldersagainst the top of the rocker stud to provide steadfast valve lash adjustment. Don’t settle for an imitation. Insist on genuine Isky Poly Locks.
Part No. Application Set of 16 (includes set screws & allen wrench)PL-7/16 Chevrolet 396-454 and Pontiac NASCAR 61-63PL-3/8 Chevrolet Small Block and Ford 221-260-289-302 V8 & Pontiac 55 and 61 and upPL-5/16 Pontiac V-8 1956-60 & Ford 351 Windsor
The following are for Isky ALUMINUM rocker arms.204-PL Chevy 265-350, 3/8 Stud (204 & 204-6 Part No.’s)204-716-PL Chevy 265-350, 7/16 Stud (204-716, 204-6-716 & 204-65-716 Part No.’s)204-96-PL Chevy 396-454 (204-96 & 204-96-8 Part No.’s) Isky First
50
ISKY VALVE TRAIN WEAPONS • ROCKER ARMS
PRECISION EQUIPMENT
Long Slot Rocker ArmsStamped Steel Rocker for Small & Big Block Chevy V-8’s. Isky “Long Slot” rocker arms areideal for high perf. street, bracket racing and oval track (hydraulic and solid lifter cam) applications where a high performance, stock appearing rocker arm is either desired or required. These precision rockers have the added insurance of a longer slot to prevent rockerto stud interference, common with stock-type rocker arms when valve lifts exceed .450-.500”.
These rockers are heat treated for added reliability and are also supplied with our new“grooved” rocker arm pivot balls to insure adequate lubrication. Also supplied is a one ouncecontainer of Isky Rev-Lube with XP-2000 for trouble free break-in!
Part No. Application Ratio Stud2015-LSR Small Block Chevy V-8 1.5 3/82016-LSR Small Block Chevy V-8 1.6 3/82017-LSR Small Block Chevy V-8 1.5 7/162018-LSR Small Block Chevy V-8 1.6 7/163960-LSR Big Block Chevy V-8 1.72 7/16
NOTE: NOT recommended for use with hydraulic and mechanical roller camshafts.
Roller Tip Rocker ArmsIsky Roller Tip Rocker Arms are stamped from high strength alloy steel and specially heattreated to resist rocker arm flex. They are engineered with the longer slot for use withhigher lift hydraulic and solid lifter cams over .500”
Each kit comes complete with our popular “Poly-Lock” adjusting nuts and grooved rockerpivot balls for added lubrication. Isky roller tip rocker arms are ideal for high perf. street,bracket racing and oval track where a roller tip rocker is allowed, yet an otherwise stockappearing rocker arm is required. Also supplied is a one ounce container of Isky Rev-Lubewith XP-2000 for trouble free break-in!
Part No. Application Ratio Stud
2025-RTR Small Block Chevy V-8 1.5 3/8
2026-RTR Small Block Chevy V-8 1.6 3/8
2027-RTR Small Block Chevy V-8 1.5 7/16
2028-RTR Small Block Chevy V-8 1.6 7/16
NOTE: NOT recommended for use with hydraulic and mechanical roller camshafts.
* Improved Heat Treat* Long Slot Design
* Increase Horsepower* Reduce Tip-Rocker Friction* Long Slot Design* H-11 Tool Steel Roller & Pin Ass’y
Roller Arm Pivot BallsIsky Rocker Arm Pivot Balls are specially “grooved” on the lower radius to allowadded lubrication with stock style, stamped steel rocker arms when employinghigher spring pressures in high performance applications.
Available for both Small & Big Block Chevy V-8.
Part No. Application200-RAPB Small Block Chevy V-8 ~ 3/8 Stud300-RAPB Small Block Chevy V-8 ~ “TUFFTRIDE Coat” Heat Treated
wear resisting finish for high load applications 7/16 Stud only400-RAPB Big Block Chevy V-8 ~ 7/16 Stud
51
PERFORMANCE EQUIPMENT
Lash Caps
Now Available for 5/16,11/32, & 3/8" Valve Stems. Designed for use with recessed 10 Deg. Valve Locks. Top of Caps are .080" thick and the legs are.130" deep. Overall depth is .210". Machined from Premium Nickel ChromeMoly Steel, Heat Treated & Black Oxided to resist corrosion.
Part No. DescriptionLC-1000 5/16 Lash Caps (Set of 16)LC-2000 11/32 Lash Caps (Set of 16)LC-3000 3/8 Lash Caps (Set of 16)
Rotator Cups: Big Block Chevy V-8
Eliminates the need for stacking several shims underneath Dual Valve Springs when removing theexhaust rotators on Big Block Chevy V-8 cylinder heads. Cups are .300” thick.
Part No. Description
390-RC Set of 8 cups
Precision Valve Spring ShimsValve Spring Shims are a facet of overall camshaft performance. Part of this performance is fitting the valve spring to its correct height so that it exerts theproper recommended pressure. Shims are .030” thick. Specify spring diameter,single or dual springs.
Part No. OD / ID Thickness Total Shims in Set 1 1.500 x 1.000 .060” 16 2 1.425 x .700 .030” 32 3 1.250 x .650 .030” 32 4 1.250 x .875 .030” 16 5 1.540 x .625 .030 32
Micro Shim KitsThis is a precision shim kit for the mechanic who desires perfection in installing racing valve springs to a precise height. Each shim is made from tempered steel for maximum strength.
Part No. OD / ID Shims per Kit Individual Breakdown Valve Spring Applications
6 1.250 x .625 118 (20) .010” (30) .015” 205-G, 4005, 4205 (34) .020” (34) .030” 7 1.425 x .700 118 (20) .010” (30) .015” 5005, 5105, 6005, (34) .020” (34) .030” 6105, 6205 8 1.560 x .625 96 (24) .010” (24) .015” 8005-A, 8205, 8305, 9005, 9205, 9265, 9275 (24) .020” (24) .030” 9315, 9365, 9365-SP, 9375/85 PLUS, 9385 9425, 9905, 9915, 9925, 9965, 9975, 9985, 9995 9 1.625 x .625 96 (32) .015” (32) .020” 9685, 9701, 9705 (32) .030” 9801-A, 9901-A, 9945, 9955 11 1.220 x .505 32 (16) .015” (16) .030” 165-A, 195-A & 4905 (LS-1) Small Block Chevy V8
52
VALVE SPRING CUPS
VALVE SPRING LOCATORS
Valve Spring Cups locate the outside diameter of the valve spring in relation to the Valve Guide, preventing spring movement which leads to“Galling” on aluminum heads. Isky Valve Spring Cups are manufactured from Chrome Moly Steel, then heat treated for maximum durability.They are designed to fit over .625” O.D. Valve Guides.*NOTE: Spring seat area must be enlarged when installing Spring Cups.
Spring Seat Cup Dim. Dim. Dim. Dim. *Installation Corresponding Part No. A B C D Cutter Isky Spring Part No. 900-SC 1.660” 1.540” .630” .060” N/A 8005-A, 8205, 8305, 9005, 9105 940-SC 1.660” 1.560” .630” .050” N/A 9205, 9265, 9315, 9365, 9385, 9425, 9905, 9925, 9935, 9965, 9975, 9985, 9995 970-SC 1.730” 1.630” .630” .050” N/A 9685, 9705, 9945, 9955 990-SC 1.750” 1.670” .630” .060” N/A 9701, 9801-A, 9901-A
Valve Spring Locaters are designed for applications where excessive diameter machining on the cyl. head is prohibitive. They locate the inside of the inner spring in relation to the valve guide, preventing spring movement on aluminum heads. Spring locaters are manufacturedfrom Chrome Moly Steel, heat treated and are designed to fit over both .565” and .625” O.D. Valve Guides.
Spring Locater Dim. Dim. Dim. Dim. *Installation CorrespondingPart No. A B C D Cutter Isky Spring Part No.165-VSL 1.280” .880” .575” .045” – 165-A & 195-A on LT-1 & Early SB Chevy V8175-VSL 1.280” .880” .505” .045” – 165-A & 195-A on LS-1 Chevy V8185-VSL 1.280” .665” .505” .045” – 4905 on LS-1 Chevy V8255-VSL 1.250” .765” .575” .075” – 235-D on LT-1 SB Chevy V8700-VSL 1.520” .720” .570” .045” – 8005-A, 8205, 8305, 9005, 9105, 9265800-VSL 1.540” .740” .570” .045” – 9205, 9315, 9365, 9365-SP, 9375/85 PLUS, 9385
9425, 9905, 9915, 9925, 9965, 9975, 9985, 9995900-VSL 1.520” .720” .630” .045” – 8005-A, 8205, 8305, 9005, 9105, 9265940-VSL 1.540” .740” .630” .045” – 9205, 9315, 9365, 9365-SP, 9375/85 PLUS, 9385
9425, 9905, 9915, 9925, 9965, 9975, 9985, 9995950-VSL 1.500” .810” .570” .060” – 9935960-VSL 1.500” .810” .630” .060” – 9935965-VSL 1.615” .765” .570” .045” – 9685, 9705, 9945, 9955970-VSL 1.615” .765” .630” .045” – 9685, 9705, 9945, 9955
Isky 4140 Chrome Moly Split Valve Locks are too tough to stamp. Our tooling marks will prove to you that they are turned on a lathe. Beware of those cheaper split locks on the market, that are merely stock cold stamped parts (some may be case hardened for a hard surface -- but they lack core strength)!
Isky Heat Treated Locks with the proper taper angle grip your valve retainers with greater locking force and will out tensile anything on the market today. They are an absolute must for today’s Hi-RPM racing engines. Don’t take chances with blackened or plated stock type locks masquerading as genuine heat treated Isky. The safety of your racing engine demands only the best...ISKY CHROME MOLYVALVE LOCKS.
7O Locks 10O LocksPart No. Part No. Description Application
VL-5/16 VL10-5/16 For 5/16” Valve Stems Chrysler 426 hemi and Small Block Chevy V-8 Set of 32 with Special 5/16 Valves, etc.
VL-11/32 VL10-11/32 For 11/32” Valve Stems Chevy Small Block V-8, Ford 289-302 V-8 and Set of 32 Pontiac V-8 Engines, etc.
VL-3/8 VL10-3/8 For 3/8” Valve Stems Chevy 396-454 V-8, *Chrysler “B” 383 & 440, Set of 32 some Chrysler “A” Engines and Ford 332-428 V-8
*Isky Chrome Moly Valve Locks are for single groove valves only and will not fit 3 and 4 Groove Type Valve Stems.
53
VALVE LOCKS • MACHINED FROM 4140 CHROME MOLY BAR STOCK
Super 7O Valve LocksDesigned for maximum endurance in roller cammed Oval Track, RoadRacing and Drag Racing applications where maximum locking force with the valve stem is required. These heavy-duty valve locks are also machined from 4140 Chrome Moly Bar-Stock and heat treated like ourstandard 7 deg. valve locks shown above.
Super 7 Valve Locks incorporate a ground finish on the O.D. which allowsa more consistent installed height for each retainer on its valve. Super 7deg. valve locks are used in conjunction with the following Isky retainers only:
Type Isky Retainer
Chrome Moly Steel 175-ST, 275-ST, 375-ST
Titanium 91-TI, 92-TI, 94-TI, 975-TI
Part No. Application (for use with standard groove valves) Set of 32
VL-600 5/16” Valve Stem Applications
VL-650 5/16 Valve Stem Applications: +.050” higher installed height
VL-700 11/32” Valve Stem Applications
VL-750 11/32 Valve Stem Applications: +.050” higher installed height
VL-800 3/8” Valve Stem Applications
VL-850 3/8 Valve Stem Applications: +.050” higher installed height
Bead Valve Locks for use with Bead Groove Valves
Part No.
VL-1600
VL-1650
VL-1700
VL-1750
New!
The World’s Strongest
54
“ULTRA REV KITS” • ROLLER TAPPET (PATENTED) Isky Invention
Invented by Isky in 1958, the original "ULTRA-REV KIT" has nowbeen copied by most other cam grinders. A tribute to Isky's Engineering Designs.
The "ULTRA REV-KIT" is engineered to increase engine RPM andprolong roller tappet bearing life by pre-loading the roller tappets tothe cam lobe (eliminating stop-start "Skidding".)
Pre-load springs are held in place by lightweight aluminum retainingbars which install beneath the cylinder head (a drop-in installation).
Ultra Rev-Kits are included free with most roller cam & kit assembliesin this catalog, however they may be purchased separately.
REV PLATE INFORMATION CAST MACHINED HARD-COAT ALUM. ALUM. PLATE ANODIZED
200-LRK Small Block Chevy V-8 X 1271-LSH, 1271-LO
210-LRK Small Block Chevy V-8 X 272-RH
220-LRK Small Block Chevy V-8 X 272-874-RH
300-LRK Small Block Chevy V-8 X X 1271-LSH, 1271-LO
310-LRK Small Block Chevy V-8 X X 272-RH
320-LRK Small Block Chevy V-8 X X 272-874-RH
150-LRK Small Block Chevy V-8 X X 1271LO-150, 1271-LO-185, 1271-LO150-874
1300-LRK X X 1371-LSH, 1371-LO
1350-LRK X X 1371-LO-150
Small Block Chevy V-8“Bow-Tie blocks with Raised Lifter Bosses
Small Block Chevy V-8“Bow-Tie blocks with Raised Lifter Bosses
APPLICATIONPART NO. ISKY ROLLER LIFTER APPLICATION
Special Note:Included with every set of 1241-series Roller Lifters is a package of P/N 200-RTW Roller Tappet Washers, designed to protect your Roller Lifters from Rev-Spring “chaffing”. They are also available for sale in replacement form as well. P/N 200-RTW...set of sixteen (16) pieces.
NOTE:When ordering replacement Rev-Springs, use the following part numbers.
Part No. Application
1243-L Chevy 90° V-6 and Small Block V-8 (Supplied in 150, 200, 210, 300, & 310-LRK Rev Kits)
1343-L Small Block Chevy V-8 “Bow-Tie” blocks with Raised Lifter Bosses. (Supplied in 1300 & 1350-LRK Rev-Kits)
55
ISKY ADJUSTABLE GUIDE PLATES Patent No. 5,044,329
PERFORMANCE EQUIPMENT
Small Block Chevy V-8 & 90 Degree V-6* Made simple to minimize modifications assoicated with high performance factory aftermarket aluminum or cast ironcylinder heads where intake ports have been relocated from their original factory position.* Fully adjustable guide plates come with two pieces. One male and one female.* Grind centers for a closer setting.* Can easily be adjusted inward or outwards.* For more stability, guide plates can be welded once final adjustments are made.
Part No. Description
200-AGP 5/16 Diameter Pushrods
300-AGP 3/8 Diameter Pushrods
Adjustable guide plates: Set of (8) pair.
Chevy Roller Thrust BearingThis bearing nests between the camshaft sprocket and the front timing case cover. Its function is to eliminate axial float (fore and aftmovement) of the cam in the block. Unit consists of a precision needle bearing assembly contained in a steel housing which may bedisassembled for inspection. Anti-thrust bearing included FREE withChevy Roller Cam Kits.
Part No. Description
200-TB Small Block Chevy 1955-77 V8
210-TB Small Block Chevy 1978-up with shallow front cover
200-96-TB Chevy 396-454
4600-TB 426 Chrysler HemiIsky Invention
Cam Sprocket Lock Plate
This special heat treated lock plate is for all Chevy V-8s. It comes complete with three high tensilebolts for positive locking of cam sprocket to camshaft.
Part No. Application
200-LP Small & Big Block Chevy V8
56
HIGH PERFORMANCE GEAR
Heavy Duty Performance Timing Set (Small Block Chevy V-8)An economical yet durable timing set consisting of Cast Iron Cam Gear, Roller Timing Chain Assembly and a 3-Keyway "Multi-Indexed” Steel Crank Sprocket. Ideal for Supercam and Megacam Hydraulic CamInstallations. These sets are included in ourNEW "CLT" Small Block Kits. See Page 59for more information.
� PART NO. 300-TS
3 Bolt Conversion KitAll 1970 and later 440 six-pack engines usethe new 3-bolt cam sprocket and roller timingchain which is far superior to the single-boltsprocket-Now you can convert your early "B" engine to the latest 3-bolt timing gear assembly.
Part No. 1650-3BK (Cam & crank sprockets,roller chain and cam sprocket bolts)
ALUMINUM BRONZEDISTRIBUTOR GEARSIsky aluminum bronze distributor gears replacefactory cast-iron gears and will withstand muchhigher loading. The aluminum-bronze gear isideal for use with steel billet roller cams
Part No. Application Shaft Dia.
200-DGS Small & Big Block .490” Chevy V-8 (Standard Rotation)
200-DGR Small & Big Block .490” Chevy V-8 (Reverse Rotation when using Isky 200-GDS Gear Drive)
250-DG Chevy II 4 & 6-Cyl .490” 230 & 250 CID
310-DG Ford 429-460 V-8 .530”
380-DG Ford 260-289-302 V-8 .467”
430-DG Ford 351 Cleveland V-8 .530”
900-DG Pontiac V-8 .490”
1600-DG Chrysler 383-440 V-8 .488”
Machined Matched Timing Gear SetThis matched timing gear set is shown in cutaway to reveal machining for Tru-Arc snap ring.Timing gear can never come off accidentally! Set includes specially heat treated aluminum timing gear with Tru-Arc snap ring and steel crankshaft gear. Set is recommended for all Chevy II 4- and 6-cylinder engines.
Note: Camshaft gear is free with all Chevy II 4- and 6-cylinder Cam Kits. Also sold separately.
Camshaft gear #250-TGMCrankshaft gear #250-CGMatched Set #250-MGS
Offset Cam BushingsBefore there were only a few expensive ways to vary your cam position relative to the crankshaft. "CAM TUNING" was the private sanctuary of the old top pros. Now anyone cando it! ISKY Offset Bushings are offered in 0, 2, 4, 6 and 8 Crankshaft degrees and are colorcoded for easy identification.
Part # Description
OFB-O-2-4-6-8 Set of 5 Offset Bushings (includes complete installation instruction) Fits all Chevrolet V-8 engines, Chrysler 383-440, 426 Hemi and Slant 6 cyl. 170-225 engines.OFB-16 6° at the crank for Olds 1949 & up V-8 engines.
Isky Invention
� Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
57
TIMING CHAIN / GEAR SETS • PRECISION-MATCHED
Isky’s timing chain and gear sets are perfectly matched and precisely machined for accurate cam to crank phasing and valve timing. ALL cam sprockets are machined from high quality “Ductile Iron” and heat treated for maximum durability.Isky sprockets and chains are the widest available for greater load-carrying and minimum chain stretch.
Part No. Application300-TS Chevrolet 283-400 Small Block V-8390-TS Chevrolet 396-454 Big Block V-8310-TS Ford 429-460 V8 (1968 and up)350-TS Ford 352-390-428 V8 (1963 and up)380-TS Ford 255-302-351 Windsor V8 (1974 and later only)430-TS Ford 351c-351m/400m V81600-TS Chrysler “B” 383-440 (Single Bolt)1650-3BK Chrysler “B” & 426 Hemi (3 Bolt Roller Chain)3900-TS Chrysler “A” 273-318-340-360620-TS Buick V8 215 Aluminum & 300-340-350 Iron1150-TS Buick 400-430-455 V8 (1967-78)1160-TS Buick V6 198-225-231 (1962-77) (Odd-Fire)1190-TS Buick V6 Even Fire 196-231-252 1977 and up (with integral dist. gear)690-TS Oldsmobile V8 330-350-400-403-425-455 cu. in.900-TS Pontiac V8 389-421-455 cu. in.1350-TS American Motors 290-401 V8 1966 and up
Often when expensive racing engines don'tperform up to par, the culprit is “Cam Walk”(the fore and aft movement of the camshaftin the Block) - more thoroughly explained in“How To Prevent Roller Cam Walk”.
To cure this perplexing problem, the “AntiCam-Walk Kit” consists of the following:
(1) Our famous Needle Bearing ThrustBumper to prevent “Forward Cam Walk.”
(2) Isky’s cam sprocket lock plate to securely fasten the “thrust bumper” andcam sprocket to the camshaft.
(3) A special precision needle thrust bearingassembly for installation between thecam sprocket and engine block, to prevent “Backward Cam Walk.”
(4) Our specially modified cam bearing insert to locate the needle thrust bearing assembly.
The only engine modification required to install the Anti Cam-Walk kit is the machiningof the engine block cam-thrust surface (to compensate for the thickness of the needle thrust bearing assembly). End your cam-walk problems forever with Isky’s “Anti-Cam-Walk Kit”.
Anti Cam-Walk Kit (with complete installation instructions)
Part No. Application
200-ACW 283-400 CHEVROLET Small Block V8200-96-ACW 396-454 CHEVROLET Big Block V8
58
ISKY TOOLS
HEIGHT MIKE:
The most accurate way to measure Valve Spring Installed Height is with the Height Mike! This tool sets in between the retainer and cylinder head spring seat. Easy to read dial (justlike a micrometer) for accurate measurements every time.
Part No. Installed Height Range
100-HM 1.400 - 1.800”
200-HM 1.600 - 2.100”
CAM DEGREEING TOOLS:
Here's a unique tool which checks the lift of the Camshaft directly from the Camshaft in the Block.Installs right inside thelifter bore, is accurate and is very simple to use. Both a flat androunded probe are included for checking Roller and Hyd/FlatTappet Cams.
Part No. Application
200-CDT All GM (.842”) and FORD (.875” Lifter BoreApplications
300-CDT All CHRYSLER & AMC (.904”) Lifter BoreApplications
ADJUSTABLE CHECKING PUSHRODS:These units are designed for checking the proper pushrod length in applicationswhere valve train geometry has been affected by modifications such as angle milled heads, decked blocks, small base circle cams, etc....Each pushrod has anadjustment range of approximately .700".
Once the proper pushrod length has been established, refer to our pushrod section. If you don't see the length you need, call our factory and we will makethem up on special order. Each package contains one pushrod, 5/16" diameter.
NOTE: NOT DESIGNED TO BE RUN IN ENGINE
Part No. Adjustment Range Application
PRC-1 6.400” - 7.100” Small Block Chevy V-8 (1241 Series Roller Lifter) 289-302 Ford V-8
PRC-2 7.650” - 8.350” 290-401 AMC V-8 283-400 Small Block Chevy V-8
PRC-3 8.000” - 8.700” 396-454 Chevy Big Block V8-Int.383 Mopar “B” V-8351-Ford Windsor V-8
PRC-4 8.350” - 9.050” 427-454 Chevy Big Block V-8 Truck Block Intake351 Ford Cleveland/Boss V-8429-460 Ford V-8
PRC-5 9.000” - 9.700” 396-454 Chevy Big Block V-8 Exhaust440-Mopar “B” V-8Pontiac V-8, 1967 & later
PRC-6 9.400” - 10.100” 427-454 Chevy Big Block V-8 Truck Block Exhaust400-M Ford V-8
59
ISKY TOOLS CAM CHECKING EQUIPMENT
“Soft Springs” “Light Tension” Spring Kit
Soft springs are the simple and practical way tocheck V/P (valve to piston clearance).
Introduced by Isky over 20 years ago, they are supplied free with every cam and kit purchase.
They may also be purchased separately and eachkit includes simple step-by-step instructions.
Part No. 100-LSK (One pair light tension springs)Part No. 116-LSK (Set of 16 light tension springs)
Isky First
Professional Cam Timing Kit
A must for today’s professional engine builder. This kit allows you to perform an ultra-precise check of cam timing in the engine. Kit includes a cast aluminum fixture which locates on the block, two extended length flat lifters, two light springs to preload the tappets, a degree wheel and full instructions.
Positive dial indicator location assures absolute parallel movement of the indicator’s stem with that of the lifters. May also be used withroller tappets. Fixture accepts standard 3/8” dia. x 2” indicator shank.(Kit does not include dial indicator shown.)
Fits 265-350 cu. in. small block Chevy V8 engines only.
Part No. 200-PCKPart No. 200-DI - 2” Travel Dial Indicator for abovePart No. 100-DI - 1” Travel Dial Indicator for Magnetic BasePart No. 100-MB - Magnetic Base and Holder for Dial Indicator
Isky First
60
ISKY TOOLS
Counter-Boring Hole Saws
Occasionally when Iskenderian designs a valve spring for a specific engine, a spring diameter may no longer match the mounting surface of the cylinder head, in which case we offer the use of these hole saws. Upon return of hole saws in good used condition, all of the original deposit, less $40.00 for rental fee, is refunded.
HOLE SAWS ARE AVAILABLE FOR ALL POPULAR SPRING DIAMETERS AS SHOWN BELOW:
Part No. O.D. ID. Deposit Required
210 1.000 .450 $120.00
208 1.250 .640 105.00
568 1.450 (stepped) .700 110.00
1448 1.450 (fiat) .700 105.00
1258 1.500 .700 105.00
3608 1.560 .700 105.00
NOTE: One Pilot is included with every hole saw. Specify Size.
HOLE SAW PILOT SIZES:
Part No. Pilot Diameter
HP-5/16 5/16
HP-11/32 11/32
HP-3/8 3/8
Piston Notching Tool
Many racers purchase custom forged pistons made to their engine specifications then find (and usually too late) that they have V/P interference (valve to piston interference) usually caused by mislocated valve pockets in the piston's domes. Only ISKY markets this tool where your own cylinder head is used to obtain perfect geometry with the valve that cuts its own proper relief in the piston dome. Available in 1 5/8, 1 3/4, 1 7/8, 2, 2 1/16, 2 1/8, 2 1/4 and 2 3/8 inch diameters for nearly any engine requirement. Proper procedure, is to choose the next larger cutting size than your valve diameter, for proper valve pocket side clearance. Pilot sizes are 5/16, 11/32 and 3/8 diameters. Perfect for the Racing mechanic or speed shop, the tool may also be rented at a nominal fee.
Cutter only (specify size) (hand driven with tap handle wrench) . . . . . . . . . . . . . . . . . . .NET $185.00Pilot (specify stem dia.) (hand driven with tap handle wrench) . . . . . . . . . . . . . . . . . . . . .NET $60.00(Rental charge) refund due customer when returned (for 1 pilot and cutter) . . . . . . . . . . . . . . .$75.00
*Above Prices are net, no further discount.P.N.T. Cutters P.N.T. PilotsPart No. Diameter Part No. Pilot Diameter
PNT-158 1 5/8” NP-516 5/16”
PNT-134 1 3/4” NP-1132 11/32”
PNT-178 1 7/8” NP-38 3/8”
PNT-200 2”
PNT-216 2 1/16”
PNT-218 2 1/8”
PNT-214 2 1/4”
PNT-238 2 3/8”
NOTE: This Tool is effective for cutting eyebrow only (up to a 50% valve face area cut). Beyond this point efficiency is significantly reduced.
Isky Invention
*Call Isky factory for availability.
61
ISKY TOOLS THE “GROOV-O-MATIC” Isky Invention
Cylinder Block O-Ringing ToolYou will discover this tool to be both an exceptional time-saver and money-maker. The amazing versatility of the "ISKY" Groov-O-Matic permitsBlock 0-Ring grooving to be done anywhere, in the shop or in the field, in only a matter of minutes.
The tool pilots in the cylinder bore & is easily adjustable for bore diameter. Also adjustable for both diameter and depth of cut for the copper 0-ring groove. This tool will undoubtedly become standard equipment for everyefficiently run speed shop. (Copper wire and complete instructions furnished with tool).
• Groov-0-Matic is the fast and profitable way to "0-Ring" the cylinder block face.• Groov-0-Matic alieviates blown head gaskets on supercharged, turbocharged or hi-compression engines.
Part No. Type & Bore Range
100-GRM “Sport Compact” Mini Groov-O-Matic (with copper wire and3 1/8 - 3 3/4 Cylinder Bores complete instructions)
200-GRM Full-Size "V8" Groov-O-Matic (with copper wire and3 3/4 - 4 3/8 Cylinder Bores complete instructions)
Rental Charge $80.00 (Tool must be purchased at your normal discount and upon return of the tool in good working order, the purchaseprice is refunded less the $80.00 rental fee.)
Groov-O-Matic Replacement Parts:
Cobalt Cutting Blades Net ea. $25.00
Aluminum Guide Bars (Standard Bores) up to 4-3/8" Net ea. $8.00 (200-GRM only)
Set of 4 Special Extension Guide Bars to fit bores up to 4.650” Net $32.00 (200-GRM only)
Copper Wire (1 lb. spool/approx. 300 ft.) Net $40.00
62
ISKY TOOLS
Valve Stem Oil SealsISKY valve stem oil seals positively control unwanted oil flow through the valveguides. They are particularly effective in racing engines by eliminating oil pollution of the combustion chamber, a horsepower robbing factor. Heavy duty steel andteflon construction.Installation requires the machining of the valve guide tops with our cutter. Isky valvestem oil seals are available in sets of 8, 12 & 16 for 4, 6 & 8 cyl. applications.
Installation cutter for seals:
Valve Stem Seal Cutter Diameter Part No. Part No.
5/16” IVS-5/16 VST-5/16
11/32” IVS-11/32 VST-11/32
3/8” IVS-3/8 VST-3/8
5/16” IVS-400 N/A LSI - Chevy V8 (late)
CC KitWhy be mystified by cubic centimeters? ISKY takes out the mystery with this handykit. The kit consists of a 100 cc graduated beaker, clear plastic combustion chamberplate, and our compression ratio wheel (circular slide rule). You can easily equalizethe volume of your combustion chambers and actually figure your true compressionratio using the graduated beaker to measure the actual combustion chamber volumewith the cylinder head attached and the piston at T.D.C. After determining the combustion chamber volume simply set the bore at the stroke on the compressionratio wheel and read your compression ratio opposite the combustion chamber volume. Simple? You bet.
Part No.202-CCK
Degree WheelA must for every engine builder, ISKYdegree wheels feature permanent anodized calibrations in one degreeincrements. Made from heavy gauge aluminum they willbecome a permanent addition to your tool box. As anadded bonus easy to follow instructions for finding T.D.C. are permanently etched on the face of the wheel. The wheel is 7" in diameter and has a 7/16" dia.center hole.
Part No.7-DW
Isky First
Isky First
63
ISKY ACCESSORIES
Cam Degreeing Made SimpleAn easy to read step by step illustrated guide to degreeing your cam. Contains complete instructionsfor the first timer as well as valuable information forthe seasoned veteran.
Decals Part No. Description Size ID-5 Racing Cams - Standard 7 1/2” x 2 1/4”* ID-6 Racing Cams - Contingency 10 3/4” x 3” ID-7 Racing Cams - Mini 2 1/4” x 3/4” ID-8 Roller Lifters 10 3/4” x 3” ID-9 Valve Springs 10 3/4” x 3” ID-12 Assortment Pack - 4 of each decal listed above
Fender CoversMade of durably strong material with soft non-slip backing that won’t scratch yourcar’s finish.
Isky Ratio ComputerHere is a necessary tool for all racing enthusiasts and engine builders. It simpy convertsMPH to RPM, or RPM to MPH. On the reverse side is a Displacement Guide which accurately figures displacement in cubic inches (or centimeters). Just dial in the strokeand number of cylinders and read the displacement opposite the bore size.
Valve Timing BookletWritten by the legendary camfather, Ed Iskenderian,“Valve Timing for Maximum Output” is the basicknowledge for today’s cam grinders. Fully illustratedwith many photos, charts and drawings, “valve timing” has for many years been required reading for many auto shop classes around the country.
*NOTE: Attention Racers . . . ID-6 is the contingencydecal needed on yourcar or boat where thereis an Isky Racing Cams contingencysponsorship in effect.
64
TECHNICAL LITERATURE / OIL
“BRAD-PENN”: King of Performance Motor Oils!Truly the worlds finest performance motor oil, BRAD-PENN is refined from 100% PurePennsylvania Grade (Paraffin Base) Crude - the best on planet earth! The original KendallRefinery in Bradford, PA is the oldest continuously operated facility in the USA, producingthe “Green Oil” Racers have come to love and trust! Endorsed by Isky as the premier oilfor protection of your flat tappet mechanical or hydraulic lifter camshaft, BRAD-PENN hasthe optimum “Zinc/Phosphate” additive package you need.
Part No.- 30 wt “Break-in” Oil BP-30- 10 w/30 Racing Oil BP-10- 20 w//50 Racing Oil BP-20
Call ISKY Factory
for current pricing.
SPECIAL NOTE: Because Pennsylvania’s finest “brad-penn” motor oils are so precisely formulated and their “zinc/phosphate” additive package has been refined to perfection, no additive is either necessary or recommended. Specificallyin fact, the company warns that the use of any normally recognized oil additive may in fact actually disrupt or dilute theiroptimized formulation. Too much of a good thing can work to your disadvantage!
CAM SHIELDTM: Restores Optimum Zinc/Phosphate Levels to motor oils!What is CAM SHIELDTM?CAM SHIELDTM is an oil supplement that contains very high concentrations of the well-known additive ZDDP (Zinc Dialkyl-Dithio-Phosphate), which has been the primary EP (Extreme Pressure) ingredient in all quality motor oils for over 70 years.
Why do I need CAM SHIELD?The EPA has placed stricter emission requirements on new cars, which have influenced manufacturers to remove ZDDP from motor oils. If you have an older car that was specified to use SF or earlier motor oil, its design requires ZDDP. Your engine could be damaged withthe use of modern SM oils. If you have a race car that runs a flat tappet mechanical or hydraulic lifter cam, your engineis at serious risk.
Can I use CAM SHIELDTM with regular and synthetic oils?CAM SHIELDTM should be compatible with all conventional (on road) and synthetic oils intended for automotive use. Virtually all of these oils have contained higher amounts of ZDDP for years and only recently have the levels been decreased.
When should CAM SHIELDTM be added?CAM SHIELDTM can be added any time, but the best time is whenever the oil is changed. A single 4 oz. bottle of CAMSHIELDTM provides the proper concentration for a 4- to 5-quart oil change.
Part No. Pkg
Cam Shield 4 oz. Bottle
ISKY ROLLER BEARING LUBE:ISKY roller bearing lube is formulated to work with any roller lifter but works ideal with ISKY Red-Zone NEEDLE roller lifters as you cansquirt the formula through the oil port on each leg. ISKY Roller Bearing Lube will insure maximum lubrication on initial “start up” duringbreak-in for needle bearings after following our instructions to thoroughly wash out the assembly grease in the bearing.
It is not necessary to use ISKY Roller Bearing Lube with our EZ-ROLLtm Plane Bearing Lifters during initial start up as these lifters are already assembled with this lube at the ISKY factory.
ISKY Roller Bearing Lube can also be periodically applied after lifter inspection for both needle and EZ-Roll Lifters (prior to being re-assembled in your motor).
Part No. Pkg
100-RBL 1 oz. Bottle
65
ABSOLUTE MAXIMUM PROTECTIONNew Formula Isky RevLubeTM with XP-2000 Prevents “Dry Start-Up” and virtuallyeliminates engine main/rod bearing, camshaft and gear wear by treating thesesurfaces with a proprietary, heat-activated, extreme pressure chemical barrier. RevLubeTM offers absolute maximum protection during engine “break-in” (the criticalmating-in period of virgin metal surfaces), because its microscopic smoothing action effectively redistributes loading over a wider surface area.
Laboratory tests confirm that RevLubeTM with XP-2000 more than doubles the actualload bearing surface area (the equivalent of reducing applied load forces in half!) Used as directed, RevLubeTM delivers unequaled protection for cam lobes, bearings,lifters, distributor drive gears, tiing chains/gears, wrist-pins, rocker arms, valvestems/guides and pushrod ends. Furthermore, you assemble with confidence because RevLubeTM will not run off -- stored engines remain protected even aftermonths of exposure to extreme temperature conditions.
Part No. Description Color
XPL-208 8 oz. Container RevLubeTM with XP-2000 RedXPL-216 16 oz. Container RevLubeTM with XP-2000 Red(Ideal for bearings, gears, wrist pins,rocker arms, valve stems/guides and pushrod ends)
RL-1 4 oz. Container of RevLubeTM BlackRL-12 (12 pack display) of 4 oz. RevLubeTM BlackRL-24 (24 pack display) of 4 oz. RevLubeTM BlackRL-48 (48 pack display) of 4 oz. RevLubeTM BlackRL-100 16 oz. Container of RevLubeTM Black(Ideal for cam and lifter assembly protection on “Flat Tappet” hydraulic & solid cams)
EliminateDry
Start-Up!
FightPrematureWear
66
ISKY APPAREL
Shop Aprons
A very useful three pocket Shop Apron. Rugged anddurable, one size fits all. Black with Isky logo onchest.
Part No. SA-100
Corduroy Hats
Available in Red, Blue and Black. Adjustable.
Part No. HAT-200 (specify color when ordering)
Jackets
Flight Jackets with our Isky Racing Cams logo embroidered emblem on front and back. This is avery popular “Racers Jacket” for all around weather use.
Available in Small, Medium, Large, X-Large and XX-Large sizes. Available in Black only.
Part No. 50-JKT
T-Shirts
“Do It Right” Isky Racing Cams logo on front. #1 for50 Years logo on back. 100% cotton.
Available in Small, Medium, Large, X-Large and XX-Large sizes. Available in White only.
Part No. SHIRT-200
67
CAM & LIFTER (CL) KITS
CAM, LIFTER & HEAVY DUTY TIMING SET (CLT) KITS
Available for Popular V8 Applications (Chevy, Chrysler, Ford, Oldsmobile and Pontiac). Our Cam & Lifter Kits (Hydraulic Assemblies) each consist of the Hydraulic Camshaft of your choice, a set of Isky “Quiet Power” HydraulicLifters, can of rev-lube and installation instructions.
To order one of these kits, just add a “CL” to the part number of the camshaft of your choice (i.e., a Small BlockChevy 262-HL/HYD cam & lifter kit would be CL-201262).
Now available for Small Block Chevy V8 only is our new (CLT) Hydraulic Cam, Lifter & Heavy Duty PerformanceTiming Set Kits. Each kit contains the Hydraulic cam of your choice, a set of Isky “Quiet Power” Hydraulic Lifters andour NEW PART NO. 300-TS Heavy Duty Performance Timing Set, consisting of Cast-Iron Cam Gear, Roller TimingChain Assembly and 3-Keyway “Multi-Index” Steel Crank Sprocket. Purchasing this as a complete kit will save youmoney and at the same time assure you of a precision timed cam installation!
To order one of these kits, just add a “CLT” to the part number of the camshaft of your choice (i.e., a 270-MEGA Hyd cam, lifter & timing set assembly would be CLT-201271). You can also add a 300-TS to one of our complete assembly kits. Doing so will save you money off the normal purchase of the timing set by itself.
Small Block Chevy V8
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
68
ISKY PERFORMANCE-ECONOMY SUPERCAMSTM
After many years of testing, Iskenderian has developed the 256 & 262 Hyd. Supercams to provide fuel economy with low end and mid range RPM performance. They are computer-designed with low valve overlap to maintain smooth idling, with specially profiled valve events to maximizevolumetric efficiency, enabling them to work with both O.E.M. and aftermarket carburetors and intake manifolds. Recommended compression ratio is between 8-10:1. Supercams will also work in conjunction with computer controls with no modifications required.
So, if you're looking to increase power and still maintain good economy, see your Isky dealer and purchase a Supercam. You'll join the thousands of satisfied customers across the nation who have proven the Supercam is the No. 1 Performance/Economy Camshaft! • 256 Hyd. Supercam is designed for normal operation of cars, vans, pick-ups, 4-WD's, etc..using high gear ratios; also light to moderate towing. • 262 Hyd. Supercam is for vehicles that demand moderately higher RPM power with lower gear ratios.
ADVERTISED LOBE HYD. LIFTER TIMING CHAIN APPLICATION PART NO. GRIND LIFT DURATION CENTER PART NO. & GEAR SET CHEVY V6, 90° 101256 256 Supercam .425 256° 112° 222-HY N/A 200-229 cu.in. 101262 262 Supercam .435 262° 108° CHEVROLET V6, 60° 111256 256 Supercam .425 256° 112° 222-HY N/A 173 cu. in. 111262 262 Supercam .435 262° 108° CHEVY V8 SMALL BLOCK 201256 256 Supercam .425 256° 112° 222-HY 300-TS *305 V-8 only *201258 256 Super cam .425 256° 108° 283-327-350-400 201262 262 Supercam .435 262° 108° CHEVY V8 BIG BLOCK 396256 256 Supercam .492 256° 112° 222-HY 390-TS 396-402-427-454 396262 262 Supercam .488 262° 108° CHEVY II 6 CYL 231256 256 Supercam .492 256° 112° 222-HY 250MGS 194-230-250 231262 262 Supercam .488 262° 109° Set of 12 CHEVY II 4 CYL 251256 256 Supercam .492 256° 112° 222-HY 250MGS 153 cu. in. engines 251262 262 Supercam .488 262° 109° Set of 8 FORD V8 311256 256 Supercam .492 256° 112° 432-HY 310-TS 429-460 311262 262 Supercam .488 262° 108° FORD V8 351256 256 Supercam .492 256° 112° 392-HY 350-TS 330-360-390-427-428 351262 262 Supercam .488 262° 108° FORD V8 381256 256 Supercam .450 256° 112° 432-HY 380-TS 221-260-289-302 381262 262 Supercam .445 262° 108° (1974-up) FORD V8 388256 256 Supercam .450 256° 112° 432-HY 380-TS 351 Windsor 388262 262 Supercam .445 262° 108° (1974-up) FORD V8 CLEVELAND 431256 256 Supercam .492 256° 112° 432-HY 430-TS 351-351-M-400-400-M 431262 262 Supercam .488 262° 108° BUICK V8 215- 621256 256 Supercam .450 256° 112° 202-HY 620-TS ALUM. 300-340-IRON 621262 262 Supercam .445 262° 110° BUICK V8 1968 & UP 671256 256 Supercam .450 256° 112° 202-HY 620-TS 350 cu. in. 671262 262 Supercam .445 262° 110° OLDS V8 1968 & UP 691256 256 Supercam .450 256° 112° 692-HY 690-TS 350-400-403-425-455 691262 262 Supercam .445 262° 108° BUICK V8 1968 & UP 115125 256 Supercam .450 256° 112° 202-HY 1150-TS 400-430-455 115126 262 Supercam .445 262° 108° BUICK V6 (1962-71) 116125 256 Supercam .450 256° 112° 202-HY 1160-TS 198-225 cu. in. engines 116126 262 Supercam .465 262° 109° Set of 12 BUICK V6 1978 & Up 119125 256 Supercam .450 256° 112° 202-HY 1190-TS (Even Fire) 196-231-252 119126 262 Supercam .465 262° 109° Set of 12 PONTIAC V8 901256 256 Supercam .425 256° 112° 692-HY 900-TS 350-389-421-428-455 901262 262 Supercam .435 262° 108° AMERICAN MTRS 6 CYL 133125 256 Supercam .450 256° 111° 3052-HY N/A 199-233-258 133126 262 Supercam .445 262° 110° Set of 12 AMERICAN MTRS V8 135125 256 Supercam .450 256° 112° 3052-HY 1300-TS 304-360-390-401 135126 262 Supercam .465 262° 108° CHRYS/PLYM. DODGE V8 160125 256 Supercam .425 256° 112° 3912-HY 1600-TS 383-413-426-440 160126 262 Supercam .435 262° 108° CHRYSLER V8 390125 256 Supercam .425 256° 112° 3912-A-HY 3900-TS 340-360 390126 262 Supercam .435 262° 108°
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: To insure maximum reliability and performance, you should also purchase a set of our premium quality“Quiet Power” Hydraulic Lifters and one of our wide-body all metal Timing Chain/Gear Sets.
69
DUAL PATTERN SUPERCAMSTM
After Extensive Testing, Iskenderian has just released the New Dual Pattern Supercams for Popular V-6 and V-8 Engines.
Like our traditional single pattern Supercams, Dual Pattern Supercams provide fuel economy with low end and mid range RPM performance. They are computer-designed with low valve overlap to maintain smooth idling and will work with both O.E.M. and aftermarket carburetors and intakemanifolds. They work best with compression ratios between 8-10:1. Dual Pattern Supercams will also work in conjunction with computer controlswith no modifications required.
Dual Pattern Supercams have shown a substantial increase in pulling power and torque in heavy towing applications with rear axle ratio's from 3:23 to 4:11! They also work well with restricted exhaust ports in stock cylinder heads. The longer exhaust duration allows better breathing and produces more overall power and torque in these applications.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
PART ADVERTISED LOBE HYD. LIFTER TIMING CHAIN APPLICATION NUMBER GRIND LIFT DURATION CENTER PART NO. & GEAR SET CHEVY V-6, 90° 101256/262 256/262 .425 256° 110° 222-HY N/A 200-229 cu. in. HYD .435 262°
CHEVROLET V-6, 60° 111256/262 256/262 .425 256° 110° 222-HY N/A 173 cu. in. HYD .435 262°
CHEVY V-8 SMALL BLOCK 201256/262 256/262 .425 256° 110° 222-HY 300-TS 283-327-350-400 HYD .435 262°
CHEVY V8 BIG BLOCK 396256/262 256/262 .492 256° 110° 222-HY 390-TS 396-402-427-454 HYD .488 262°
FORD V-8 311256/262 256/262 .492 256° 110° 432-HY 310-TS 429-460 HYD .488 262°
FORD V-8 351256/262 256/262 .492 256° 110° 392-HY 350-TS 330-360-390-427-428 HYD .488 262°
FORD V-8 381256/262 256/262 .450 256° 110° 432-HY 380-TS 221-260-289-302 HYD .445 262° (1974-up)
FORD V-8 388256/262 256/262 .450 256° 110° 432-HY 380-TS 351 Windsor HYD .445 262° (1974-up)
FORD V-8 CLEVELAND 431256/262 256/262 .492 256° 110° 432-HY 430-TS 351-351-M-400-400-M HYD .488 262°
OLDS V-8 1968 & UP 691256/262 256/262 .450 256° 110° 692-HY 690-TS 350-400-403-425-455 HYD .445 262°
BUICK V-6 1975-77 (Odd Fire) 117125/26 256/262 .450 256° 110° 202-HY 1160-TS 231 cu. in. engines HYD .465 262° Set of 12
BUICK V-6 1978 & Up 119125/26 256/262 .450 256° 110° 202-HY 1190-TS (Even Fire) 196-231-252 HYD .465 262° Set of 12
PONTIAC V-8 901256/262 256/262 .425 256° 110° 692-HY 900-TS 350-389-421-428-455 HYD .435 262°
AMERICAN MOTORS 6 CYL 133125/26 256/262 .450 256° 110° 3052-HY N/A 199-233-258 HYD .445 262° Set of 12
CHRYS./PLYM./DODGE V8 160125/26 256/262 .425 256° 110° 3912-HY 1600-TS 383-413-426-440 HYD .435 262°
CHRYSLER/PLYMOUTH V8 165125/26 256/262 .425 256° 110° 3912-HY 1650-3BK (3-Bolt Cam) 383-413-426-440 HYD .435 262°
INTERNATIONAL V8 190125/26 256/262 .450 256° 110° N/A N/A 304-345-392 cu. in. HYD .465 262°
CHRYSLER V8 390125/26 256/262 .425 256° 110° 3912-A-HY 3900-TS 340-360 HYD .435 262°
70
ISKY MEGA-CAMSTM • THE LATEST & MOST POWERFUL HYDRAULIC CAMS
CHEVROLET • V8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
Utilizing the latest advances in computer technology combined with forty-five years of experience, no wonder over 100,000satisfied customers worldwide have proven Isky Mega-CamsTM to be the most powerful hydraulic cams available.
The Mega-Cam line was designed to produce more power over a broader RPM range. By having this wider range, gearratio and weight can easily be compromised, minimizing the sacrifice of low-end performance to gain top end horsepowerand creating a truly versatile line of performance cams.
Recommended For... High Performance Use: Bracket Racing, Oval Track Racing, Marine, 4-WD and Off Road Use.
CAM TUNING FOR MAXIMUM OUTPUT
RECOMMENDED RPM CARB GRIND DESCRIPTION IDLE RANGE AXLE CFM TRANS RATIO RATING
264 Mega Hyd. Compression Ratio: 9-10.5:1 Good 2000-5800 Any 3.23/3.70 up to 625 Tremendous Torque and good Mid-Range Power CFM
270 Mega Hyd. Compression Ratio: 9-10.5:1 Fair 2000-6200 Manual or Auto 3.70/4.11 550-650 Excellent Mid-Range Performance w/Stock Converter
280 Mega Hyd. Compression Ratio: 9.5-10.5:1 Lopey 2500-6800 Manual or Auto 3.90/4.11 625-780 Combination High Performance Use/Bracket with 2500 RPM Racing Converter
292 Mega Hyd. Compression Ratio: 10-11:1 Rough 3000-7000 Manual or Auto 4.11/4.56 650-780 Combination Hi-Performance Use/Bracket with 2800 RPM Racing Converter
304 Mega Hyd. Compression Ratio: 11:1 & Up Rough 3200-7500 Manual or Auto 4.33/4.88 700-850 Ultimate Hi-Performance Use/Bracket with 3000 RPM Racing Converter
NOTE: Dual pattern mega-cams also available. Contact your local speed shop or Isky Factory Direct for purchasing information.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Part No. Grind No./Type Application RPM-Range Lift Lash Hot Duration Duration Lobe Cam Only INT. EX. INT. EX. INT. EX. INT. EX. Center 201SL1/14 SL-1 Classes where stock lift rules apply; 2400-6600 .390 .000 268º 228º 114º HYDRAULIC 16” Vacuum @ 1,000 RPM .410 .000 272º 232º 201SL3 SL-3 Classes where stock lift rules apply; 2000-5700 .390 .000 252º 208º 114º HYDRAULIC 18” Vacuum @ 750 RPM .410 .000 260º 216º 201LR1/14 LR-1 .420” lift rule class; 2200-6400 .415 .000 264º 224º 114º HYDRAULIC 16” Vacuum @ 1000 RPM .415 .000 264º 224º 201268/14 268-MEGA .450” lift rule class; 2200-6400 .450 .000 268º 224º 114º HYDRAULIC 16” Vacuum @ 1000 RPM .450 .000 268º 224º 201264/14 264-MEGA .450” lift rule class; 2200-6000 .450 .000 264º 214º 114º HYDRAULIC 16” Vacuum @ 800 RPM .450 .000 264º 214º 201271/14 270-MEGA Hobby stock & street stock classes: 2200-6400 .465 .000 270º 221º 114º HYDRAULIC 16” vacuum @ 1000 RPM .465 .000 270º 221º
Vacuum Rule / Oval Track:With the increased enforcement of vacuum rule camshafts at many oval tracks across the country, Isky has introduced several newMega Hydraulic grinds to meet this demand. The most popular applications are listed below. More grinds will be added in the near future.
71
ISKY MEGA-CAMSTM • AVAILABLE FOR THESE POPULAR V-8 ENGINES
CAM ONLY CAM & KIT ADVERTISED .050” LOBE APPLICATION PART NO. PART NO. GRIND TYPE LIFT DURATION DURATION CENTER
Small BlockChevy V8 201264 200264 264-Mega-cam Hyd. .450” 264° 214° 108° 201271 200271 270-Mega-cam Hyd. .465” 270° 221° 108° 201281 200281 280-Mega-cam Hyd. .485” 280° 232° 108° 201292 200292 292-Mega-cam Hyd. .505” 292° 244° 108° 201304 200304 304-Mega-cam Hyd. .525” 304° 256° 108° Big Block Chevy V8 396264 390264 264-Mega-cam Hyd. .525” 264° 214° 108° 396271 390271 270-Mega-cam Hyd. .542” 270° 221° 108° 396281 390281 280-Mega-cam Hyd. .565” 280° 232° 108° 396282 390282 280-Mega-cam Hyd. .565” 280° 232° 110° 396292 390292 292-Mega-cam Hyd. .590” 292° 244° 108° 396304 390304 304-Mega-cam Hyd. .612” 304° 256° 108° Ford 429/460 V8 311264 310264 264-Mega-cam Hyd. .525” 264° 214° 108° 311271 310271 270-Mega-cam Hyd. .542” 270° 221° 108° 311281 310281 280-Mega-cam Hyd. .565” 280° 232° 108° Ford 360/390/428 V8 351264 350264 264-Mega-cam Hyd. .525” 264° 214° 108° 351271 350271 270-Mega-cam Hyd. .542” 270° 221° 108° 351281 350281 280-Mega-cam Hyd. .565” 280° 232° 108° Ford 289/302 V8 381264 380264 264-Mega-cam Hyd. .480” 264° 214° 108° 381271 380271 270-Mega-cam Hyd. .496” 270° 221° 108° 381281 380281 280-Mega-cam Hyd. .517” 280° 232° 108° 381292 380292 292-Mega-cam Hyd. .538” 292° 244° 108° 381304 380304 304-Mega cam Hyd. .560” 304° 256° 108° Ford 351/400 431264 430264 264-Mega-cam Hyd. .525” 264° 214° 108° Cleveland V8 431271 430271 270-Mega-cam Hyd. .542” 270° 221° 108° 431281 430281 280-Mega-cam Hyd. .565” 280° 232° 108° 431292 430292 292-Mega-cam Hyd. .590” 292° 244° 108° Olds 350-455 late V8 691264 690264 264-Mega-cam Hyd. .480” 264° 214° 108° 691271 690271 270-Mega-cam Hyd. .496” 270° 221° 108° 691281 690281 280-Mega-cam Hyd. .517” 280° 232° 108° 691291 690291 292-Mega-cam Hyd. .538” 292° 244° 108° 691304 690304 304-Mega-cam Hyd. .560” 304° 256° 108° Pontiac V8 901264 900264 264-Mega-cam Hyd. .450” 264° 214° 108° 901271 900271 270-Mega-cam Hyd. .465” 270° 221° 108° 901281 900281 280-Mega-cam Hyd. .485” 280° 232° 108° 901292 900292 292-Mega-cam Hyd. .505” 292° 244° 108° 901304 900304 304-Mega cam Hyd. .525” 304° 256° 108° Chrysler “B” 383-440 V8 160164 160064 264-Mega-cam Hyd. .450” 264° 214° 108° Single Bolt 160171 160071 270-Mega-cam Hyd. .465” 270° 221° 108° 160181 160081 280-Mega-cam Hyd. .485” 280° 232° 108° 160129 160029 292-Mega-cam Hyd. .505” 292° 244° 108° 160134 160034 304-Mega cam Hyd. .525” 304° 256° 108° Chrysler “B” 383-440 V8 165164 165064 264-Mega-cam Hyd. .450” 264° 214° 108° “3-Bolt” 165171 165071 270-Mega-cam Hyd. .465” 270° 221° 108° 165181 165081 280-Mega-cam Hyd. .485” 280° 232° 108° 165129 165029 292-Mega-cam Hyd. .505” 292° 244° 108° 165134 165034 304-Mega cam Hyd. .525” 304° 256° 108° Chrysler “A” 273-340 390164 390064 264-Mega-cam Hyd. .450” 264° 214° 108° 360 V8 390171 390071 270-Mega-cam Hyd. .465” 270° 221° 108° 390181 390081 280-Mega-cam Hyd. .485” 280° 232° 108° 390129 390029 292-Mega-cam Hyd. .505” 292° 244° 108° 390134 390034 304-Mega cam Hyd. .525” 304° 256° 108°
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
72
AMERICAN MOTORS • V-8 1966-and up 304 Jeep and 360 cu. in. engines only
AMERICAN MOTORS • V-8 1966-and up 290-343-390-401 cu. in. engines
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
135125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
135125/26 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .465 .000 262° 208°
135126 262-SUPERCAM 2000-5500 .465 .000 262° 208° 108° HYDRAULIC .465 .000 262° 208°
135127 270-HL 2000-6000 .470 .000 270° 216° 108° HYDRAULIC .470 .000 270° 216°
135128 280-HL 2500-6500 .490 .000 280° 224° 108° HYDRAULIC .490 .000 280° 224°
Cast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
135125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
135125/26 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .465 .000 262° 208°
135126 262-SUPERCAM 2000-5500 .465 .000 262° 208° 108° HYDRAULIC .465 .000 262° 208°
135127 270-HL 2000-6000 .470 .000 270° 216° 108° HYDRAULIC .470 .000 270° 216°
135128 280-HL 2500-6500 .490 .000 280° 224° 108° HYDRAULIC .490 .000 280° 224°
Cast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4.10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up to 650 CFM Carb.9.5:1 Compr.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4.10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up to 650 CFM Carb.9.5:1 Compr.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
73
AMERICAN MOTORS • V-8 1966-and up 304 Jeep and 360 cu. in. engines only
AMERICAN MOTORS • V-8 1966-and up 290-343-390-401 cu. in. engines
RACING CAMS
These items included in Cam & complete kit Optional accessories
CAM & CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
134025 — 3052-HY 1343-AJ 8005-AB # 2 3607-ST N/A 1350-TS VL-3/8 VS-3/8Q
134025/26 — 3052-HY 1343-AJ 8005-AB # 2 3607-ST N/A 1350-TS VL-3/8 VS-3/8Q
134026 — 3052-HY 1343-AJ 8005-AB # 2 3607-ST N/A 1350-TS VL-3/8 VS-3/8Q
134027 — 3052-HY 1343-AJ 8005-AB # 2 3607-ST N/A 1350-TS VL-3/8 VS-3/8Q
134028 — 3052-HY 1343-AJ 8005-AB # 2 3607-ST N/A 1350-TS VL-3/8 VS-3/8Q
Recommended Valve Train Components
B Requires cylinder heads be machined with Isky #1258 Hole Saw J Adjustable Pushrods
K 1309 Studs are Mandatory when using PL-3/8 Poly Locks. Q Requires cylinder heads be machined with VST-3/8 Cutter
RACING CAMS
These items included in Cam & complete kit Optional accessories
CAM & CAM & SCREW-IN VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTER LIFTERS ROCKER STUDS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 49 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
135025 — 3052-HY 1309K 8005-AB # 2 3607-ST PL-3/8K 1350-TS VL-3/8 VS-3/8Q
135025/26 — 3052-HY 1309K 8005-AB # 2 3607-ST PL-3/8K 1350-TS VL-3/8 VS-3/8Q
135026 — 3052-HY 1309K 8005-AB # 2 3607-ST PL-3/8K 1350-TS VL-3/8 VS-3/8Q
135027 — 3052-HY 1309K 8005-AB # 2 3607-ST PL-3/8K 1350-TS VL-3/8 VS-3/8Q
135028 — 3052-HY 1309K 8005-AB # 2 3607-ST PL-3/8K 1350-TS VL-3/8 VS-3/8Q
Recommended Valve Train Components
74
AMERICAN MOTORS • 6-CYLINDER 199-232-258 cu. in. engines
BUICK SPECIAL • V-8 1961-67
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
621256 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
621262 262-SUPERCAM 2000-5500 .445 .000 262° 208° 110° HYDRAULIC .445 .000 262° 208°
621270 270-HL 2000-6000 .470 .000 270° 216° 109° HYDRAULIC .470 .000 270° 216°
621282 282 ` 2500-6500 .467 .000 282° 224° 109° HYDRAULIC .467 .000 282° 224°
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
1331-M Mile-A-Mor 1000-3800 .425 .000 248° 194° 108° HYDRAULIC .425 .000 248° 194°
133125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 111° HYDRAULIC .450 .000 256° 202°
133125/26 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .445 .000 262° 208°
133126 262-SUPERCAM 2000-5500 .445 .000 262° 208° 109° HYDRAULIC .445 .000 262° 208°
133127 270-HL 2000-6000 .475 .000 270° 216° 109° HYDRAULIC .475 .000 270° 216°
133128 282 2500-6500 .467 .000 282° 224° 109° HYDRAULIC .467 .000 282° 224°
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
Best torque & economy in 327-400 c.l. Passenger cars &trucks. Max. compr. 9.5:1. Smooth idle. Std axle ratio, good vacuum, computer compatible. Std to 600 CFM Carb.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Mileage & Maximum Lower RPM Torque for Late Model,Low Compression (8-9.5:1 Max) Engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4.10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
300-340 cu.in. Cast Iron Engines215 cu. in Aluminum Engines
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
75
AMERICAN MOTORS • 6-CYLINDER 199-232-258 cu. in. engines
BUICK SPECIAL • V-8 1961-67
RACING CAMSRecommended Valve Train Components
RACING CAMSRecommended Valve Train Components
300-340 cu.in. Cast Iron Engines215 cu. in Aluminum Engines
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
1331-MK 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
133025 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
133025/26 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
133026 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
133027 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
133028 3052-HY 693-BJ 6005B # 2 3607-ST — N/A VL-3/8 VS-3/8Q
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs) (12 pcs) (24 pcs) (12 pcs)
CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
1033 (215 CI) 625256 202-HY 1033-A (300 CI) 625/626 # 3 627-ST N/A 620-TSL N/A VS-11/32F 1193-A (340 CI)
1033 (215 CI) 625262 202-HY 1033-A (300 CI) 625/626 # 3 627-ST N/A 620-TSL N/A VS-11/32F 1193-A (340 CI)
1033 (215 CI) 625270 202-HY 1033-A (300 CI) 625/626 # 3 627-ST N/A 620-TSL N/A VS-11/32F 1193-A (340 CI)
1033 (215 CI) 625282 202-HY 1033-A (300 CI) 625/626 # 3 627-ST N/A 620-TSL N/A VS-11/32F 1193-A (340 CI)
These items included in Cam & complete kit Optional accessories
F Requires cylinder heads be machined with VST -11/32 Cutter J Adjustable Pushrods L 300 & 340 C.I. Engines only
Q Requires cylinder heads be machined with VST-3/8 Cutter B Requires cylinder heads be machined with Isky #1258 hole Saw
76
BUICK • V-8 1968-and up 350 cu. in. engines (1977-and up � BUICK 350 SEE NOTE BELOW)
BUICK • V-6 1962-71 198-225 cu. in. engines (Also AMC Jeep V-6 1965-71)
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
671-M Mile-A-Mor 1000-3800 .425 .000 248° 194° 108° HYDRAULIC .425 .000 248° 194°
671256 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
671262 262-SUPERCAM 2000-5500 .445 .000 262° 208° 110° HYDRAULIC .445 .000 262° 208°
671282 282 2500-6500 .467 .000 282° 224° 109° HYDRAULIC .467 .000 282° 224°
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
Mileage & Maximum Lower RPM Torque for Late Model,Low Compression (8-9.5:1 Max) Engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
116125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
116126 262-SUPERCAM 2000-5500 .465 .000 262° 208° 109° HYDRAULIC .465 .000 262° 208°
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
� General Motors has distributed engines from one division to another in recent years. Specifically1977-81 Buicks may come equipped with eitherBuick, Chevy or Oldsmobile built 350 cu. in. V8 engines. Be sure of which G.M. Division built your engine before ordering.
77
BUICK • V-8 1968-and up 350 cu. in. engines
BUICK • V-6 1962-71 198-225 cu. in. engines (Also AMC Jeep V-6 1965-71)
RACING CAMSRecommended Valve Train Components
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
670-MK 202-HY 1193-A(1968-69)
625/626 # 3 627-ST N/A 620-TS N/A VS-3/8Q 233 (1970& UP)
670256 202-HY 1193-A(1968-69)
625/626 # 3 627-ST N/A 620-TS N/A VS-3/8Q 233 (1970& UP)
670262 202-HY 1193-A(1968-69)
625/626 # 3 627-ST N/A 620-TS N/A VS-3/8Q 233 (1970& UP)
670282 202-HY 1193-A(1968-69)
625/626 # 3 627-ST N/A 620-TS N/A VS-3/8Q 233 (1970& UP)
CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
116025 202-HY 1053J,L
625/626 # 3 627-ST N/A N/A N/A N/A 1103
J,L
116026 202-HY 1053J,L
625/626 # 3 627-ST N/A N/A N/A N/A 1103
J,L
J Adjustable Pushrods L For 1962, 198 cu. c.i. Engines only Q Requires cylinder heads be machined with VST-3/8 Cutter
These items included in Cam & complete kit Optional accessories
(12 pcs) (12 pcs)
(12 pcs) (12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
78
BUICK • V-6 1975-77 231 cu. in. “ODD FIRE” Engines Only
BUICK • V-6 1978 and UP 196-231-252 cu. in. “EVEN FIRING” Engines
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
RACING CAMSCast Iron Billet
HYDRAULIC1.6:1 Rocker Ratio
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
1171-M Mile-A-Mor 1000-3800 .425 .000 248° 194° 108° HYDRAULIC .425 .000 248° 194°
117125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
117126 262 SUPERCAM 2000-5500 .465 .000 262° 208° 109° HYDRAULIC .465 .000 262° 208°
117127 270-HL 2000-6000 .470 .000 270° 216° 109° HYDRAULIC .470 .000 270° 216°
1171-TA TURBOCYCLE-A 1000-5000 .445 .000 262° 208° 114° HYDRAULIC .415 .000 250° 194°
Maximum economy/torque. Turbocharged. Up to 7PSI Boost. Smooth idle. Stock converter. Std. axleratio. Up to 650 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
Mileage & Maximum Lower RPM Torque for Late Model,Low Compression (8-9.5:1 Max) Engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
1191-M Mile-A-Mor 1000-3800 .425 .000 248° 194° 108° HYDRAULIC .425 .000 248° 194°
119125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
119126 262-SUPERCAM 2000-5500 .465 .000 262° 208° 109° HYDRAULIC .465 .000 262° 208°
119127 270-HL ` 2000-6000 .470 .000 270° 216° 109° HYDRAULIC .470 .000 270° 216°
1191-TA TURBOCYCLE-A 1000-5000 .445 .000 262° 208° 114° HYDRAULIC .415 .000 250° 194°
Mileage & Maximum Lower RPM Torque for Late Model,Low Compression (8-9.5:1 Max) Engines.
Maximum economy/torque. Turbocharged. Up to 7PSI Boost. Smooth idle. Stock converter. Std. axleratio. Up to 650 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
79
BUICK • V-6 1975-77 231 cu. in. “ODD FIRE” Engines Only
BUICK • V-6 1978 and UP 196-231-252 cu. in. “EVEN FIRING” Engines
RACING CAMSRecommended Valve Train Components
RACING CAMSRecommended Valve Train Components
J Adjustable Pushrods N Aluminum retainers
CAM & VALVE SPRING STEEL VALVE TIMING COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 53 P. 56-57
1191-MK 202-HY 1173-CAJ 625/626 # 3 707-ALN — 1190-TS
119025 202-HY 1173-CAJ 625/626 # 3 707-ALN — 1190-TS
119026 202-HY 1173-CAJ 625/626 # 3 707-ALN — 1190-TS
119027 202-HY 1173-CAJ 625/626 # 3 707-ALN — 1190-TS
1190-TKA 202-HY 1173-CAJ 625/626 # 3 707-ALN — 1190-TS
These items included in Cam & complete kit Optional accessories
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)(12 pcs)(12 pcs)(12 pcs)
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL VALVE TIMING COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 53 P. 56-57
1171-MK 202-HY 1173-CAJ 625/626 # 3 627-ST — 1160-TS
117025 202-HY 1173-CAJ 625/626 # 3 627-ST — 1160-TS
117026 202-HY 1173-CAJ 625/626 # 3 627-ST — 1160-TS
117027 202-HY 1173-CAJ 625/626 # 3 627-ST — 1160-TS
1170-TKA 202-HY 1173-CAJ 625/626 # 3 627-ST — 1160-TS
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
80
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
1151-M Mile-A-Mor 1000-3800 .425 .000 248° 194° 108° HYDRAULIC .425 .000 248° 194°
115125 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
115126 262-SUPERCAM 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
115128 280 2500-6500 .467 .000 280° 224° 108° HYDRAULIC .467 .000 280° 224°
BUICK • V-8 1967-and up 400-430-455 cu. in. Engines
CORVAIR
RACING CAMS1.6:1 Rocker Ratio
RACING CAMSCast Iron Billet
HYDRAULIC1.5:1 Rocker Ratio
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
Mileage & Maximum Lower RPM Torque for Late Model,Low Compression (8-9.5:1 Max) Engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
221260 260 2000-5500 .417 .000 260° 208° 108° HYDRAULIC .417 .000 260° 208°
221270 270-HL 2000-6000 .440 .000 270° 216° 108° HYDRAULIC .440 .000 270° 216°
221280 280 2500-6500 .440 .000 280° 224° 108° HYDRAULIC .440 .000 280° 224°
221300 300 3000-6800 .440 .000 300° 234° 108° HYDRAULIC .440 .000 300° 234°
High Perf. Street/strip. Lopey idle. 2800 Stall.4.11-4.88 axle ratio. Up to 750 CFM Carb.10.5:1 compr.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
High Perf. Use. Lopey idle. 2500 Stall. 3.70-4.11 axleratio. Up to 750 CFM Carb. 9.5:1 compr.
Cast Iron Billet
HYDRAULIC
81
BUICK • V-8 1967-and up 400-430-455 cu. in. engines
CORVAIR
RACING CAMSRecommended Valve Train Components
RACING CAMSRecommended Valve Train Components
F Requires cylinder heads be machined with VST-11/32 Cutter J Adjustable Pushrods (1970-77 engines) with oil hole Q Requires cylinder heads be machined with VST-3/8 Cutter
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS ALUMINUM LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 RETAINERS P. 49 P. 56-57 P. 53 P. 52
1151-MK 202-HY 1193-A
7005 # 3 1007-AL N/A 1150-TS N/A VS-3/8Q 663-BJ (1970-77)
115025 202-HY 1193-A
7005 # 3 1007-AL N/A 1150-TS N/A VS-3/8Q 663-BJ (1970-77)
115026 202-HY 1193-A
7005 # 3 1007-AL N/A 1150-TS N/A VS-3/8Q 663-BJ (1970-77)
115028 202-HY 1193-A
7005 # 3 1007-AL N/A 1150-TS N/A VS-3/8Q
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS ALUMINUM LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 RETAINERS P. 49 P. 56-57 P. 53 P. 52
220260 222-HY N/A 4005 # 3 707-AL PL-3/8 N/A VL-32 VS-11/32F
220270 222-HY N/A 4005 # 3 707-AL PL-3/8 N/A VL-32 VS-11/32F
220280 222-HY N/A 4005 # 3 707-AL PL-3/8 N/A VL-32 VS-11/32F
220300 222-HY N/A 4005 # 3 707-AL PL-3/8 N/A VL-32 VS-11/32F
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(24 pcs)
(24 pcs)
(24 pcs)
(24 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
82
CHEVY II • 1962-71 4 Cylinder 153 cu. in. Engines
CHEVROLET • 409 cu. in. V-8 (1958-65)
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
RACING CAMS
RACING CAMS
HYDRAULIC
SOLID 1.75:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
251256 256-SUPERCAM 1500-4800 .493 .000 256° 202° 112° HYDRAULIC .493 .000 256° 202°
251262 262-SUPERCAM 2000-5500 .488 .000 262° 208° 109° HYDRAULIC .488 .000 262° 208°
251270 270-HL 2000-6000 .510 .000 270° 216° 109° HYDRAULIC .510 .000 270° 216°
251525 525-A 2000-6000 .525 .025 268° 228° 109° SOLID .525 .025 268° 228°
251526 525-B 2500-6500 .525 .025 278° 238° 109° SOLID .525 .025 278° 238°
251565 565 3500-7000 .565 .025 290° 242° 109° SOLID .565 .025 290° 242°
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
Strong low-end and mid-range power on 1/4-3/8 mile ovaltracks with little or no bank. Limited carburetion.
Great mid-range power on 1/4-3/8 mile oval tracks(banked). Works best with 2-BBL. Carburetion
Broad power-band on banked 3/8-1/2 mile fast oval tracks.2-BBL Carburetion.
HYDRAULIC
SOLID
ROLLER
1.7:1 Rocker Ratio
New cam cores are now available. We can custom grind hydraulic, hydraulic roller, solid and mech roller camshafts to suitcustomers’ applications. Kit components such as lifters (hydraulic, hydraulic roller, solid and mech roller), valve springs,steel retainers, valve locks and pushrods are also available. Call the Isky factory for more information.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
241256 256-SUPERCAM 1500-4800 .478 .000 256° 202° 112° HYDRAULIC .478 .000 256° 202°
241262 262-SUPERCAM 2000-5500 .474 .000 262° 208° 110° HYDRAULIC .474 .000 262° 208°
241270 270-HL 2000-6000 .495 .000 270° 216° 110° HYDRAULIC .495 .000 270° 216°
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stockConverter. 3:70-4:11 Axle Ratio. Up tp 650 CFM Carb.9.5:1 Compr.
83
CHEVY II • 1962-71 4 cylinder 153 cu. in. Engines
RACING CAMSRecommended Valve Train Components
� When installing 204-96 Rocker Arms, you must also convert to #219-A studs and 233-HG+125 Pushrods. B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter P Nose of cam has been grooved for snap ring to prevent gear movement. Gear is supplied FREE with cam. ISKY 250-TGM cam gear must be used with Cloyes #2501 or ISKY 250CG crank gear.
These items included in Cam & complete kit Optional accessories
CAM & MODIFIED BRONZE PUSH VALVE SPRING STEEL POLY ROCKER VALVE VALVE COMPLETE TIMING LIFTERS DIST. RODS SPRINGS SHIMS RETAINERS LOCKS ARMS LOCKS SEALS KIT P/N GEAR P. 56 P. 10-25 GEAR P.56 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 49 P. 53 P. 52
250256 250-TGMP 202-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
250262 250-TGMP 202-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
250270 250-TGMP 202-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
250525 250-TGMP 202-H 250-DG — 4205 # 3 707-ST PL-3/8 204-96 VL-32 VS-11/32F
250526 250-TGMP 202-H 250-DG — 4205 # 3 707-ST PL-3/8 204-96 VL-32 VS-11/32F
250565 250-TGMP 202-H 250-DG — 6005 B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs) (8 pcs) (8 pcs) (8 pcs) (16 pcs) (8 pcs)
(8 pcs)
(8 pcs)
(8 pcs)
�
�
�
84
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
231-M Mile-A-Mor 1000-3800 .450 .000 248° 194° 109° HYDRAULIC .450 .000 248° 194°
231256 256-SUPERCAM 1500-4800 .492 .000 256° 202° 112° HYDRAULIC .492 .000 256° 202°
231262 262-SUPERCAM 2000-5500 .488 .000 262° 208° 109° HYDRAULIC .488 .000 262° 208°
231270 270-HL 2000-6000 .510 .000 270° 216° 109° HYDRAULIC .510 .000 270° 216°
231-TA TURBOCYCLE-A 1000-5000 .485 .000 264° 208° 114° HYDRAULIC .455 .000 252° 194°
231525 525-A 2000-6000 .525 .025 268° 228° 109° SOLID .525 .025 268° 228°
231526 525-B 2500-6500 .525 .025 278° 238° 109° SOLID .525 .025 278° 238°
231527 525-C 2700-7000 .525 .016 278° 248° 105° SOLID .525 .018 278° 248°
231565 565 3500-7000 .572 .025 290° 242° 109° SOLID .572 .025 290° 242°
231595 595-A 4000-7500 .591 .028 298° 254° 106° SOLID .591 .028 298° 254°
CHEVY II • 6 Cylinder 194-230-250 cu. in. Engines
RACING CAMS
HYDRAULIC
SOLID 1.75:1 Rocker Ratio
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Mileage & maximum lower RPM torque for late model, low compression (8-9.5:1 max) engines.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to625 CFM Carb.
Good all-around performance. Fair idle. Stockconverter. 3.70-4.11 axle ratio. Up to 650 CFM Carb.9.5:1 compr.
Maximum economy/torque. Turbocharged. Up to 7 PSIBoost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
Strong low-end and mid-range power on 1/4-3/8 mileoval tracks with little or no bank. Limited carburetion.
Good mid-range power on 1/4-3/8 mile oval tracks(banked). Works best with 2-BBL carburetion.
Broad power-band on banked 3/8-1/2 mile fast ovaltracks. 2-BBL carburetion.
Best overall cam for high-banked, fast oval (1/2-5/8 miletracks) or road racing. Good power band for drag raceuse as well.
Great mid-range power on banked 1/4-3/8 miletracks & 2-BBL carburetion.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
85
CAM & MODIFIED BRONZE PUSH VALVE SPRING STEEL POLY ROCKER VALVE VALVE COMPLETE TIMING LIFTERS DIST. RODS SPRINGS SHIMS RETAINERS LOCKS ARMS LOCKS SEALS KIT P/N GEAR P. 56 P. 10-25 GEAR P.56 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 49 P. 53 P. 52
231-MK 250-TGMP 222-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
230256 250-TGMP 222-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
230262 250-TGMP 222-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
230270 250-TGMP 202-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
230-TKA 250-TGMP 222-HY — — 205-D # 4 707-ST PL-3/8 — VL-32 VS-11/32F
230525 250-TGMP 202-H — — 6005B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
230526 250-TGMP 202-H — — 6005B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
230527 250-TGMP 202-H — — 6005B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
230565 250-TGMP 202-H — — 6005B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
230595 250-TGMP 202-H — — 6005B # 2 507-ST PL-3/8 204-96 VL-32 VS-11/32F
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs) (12 pcs) (12 pcs)(12 pcs) (24 pcs) (12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
�
�
�
�
�
CHEVY II • 6 Cylinder 194-230-250 cu. in. Engines
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
� When installing 204-96 Rocker Arms, you must also convert to #219-A studs and 233-HG+125 Pushrods. B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter P Nose of cam has been grooved for snap ring to prevent gear movement. Gear is supplied FREE with cam. ISKY 250-TGM cam gear must be used with Cloyes #2501 or ISKY 250CG crank gear.
86
CHEVROLET • 6-Cylinder 1963 and up 292 Truck Engines � SEE FOOT NOTE BELOW, 1971 & UP
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
291462 E-462 1500-4800 .410 .015 264° 109° SOLID .410 .015 264°
291162 X-162 2000-5500 .428 .018 286° 220° 109° SOLID .428 .018 286° 220°
291262 X-262 2500-6000 .428 .018 296° 228° 109° SOLID .428 .018 296° 228°
291505 505-A-62 3000-6500 .525 .025 300° 228° 109° SOLID .525 .025 300° 228°
291506 505-B-62 3500-7000 .525 .025 310° 250° 109° SOLID .525 .025 310° 250°
291507 505-C-62 4000-7500 .558 .025 320° 252° 109° SOLID .558 .025 320° 252°
RACING CAMS
RACING CAMS
1.75:1 Rocker Ratio
Good mid-range performance. 3.23-3.70 axle ratio.Re-jetted stock carburetor. Fair idle.
Good low-speed power & torque for stock engines. Std.rear-axle ratio. Std. carburetion. Smooth idle.
High performance use. 3.70-4:10 axle ratio. 2-BBLcarburetor recommended. Lopey idle.
Best overall performance on banked 1/4-3/8 mile ovaltracks. 2-BBL carb.
Best overall performance on banked 1/2 mile oval tracks. 2-BBL carb. Good results in drag race as well.
Drag race use. Fully modified engine with highercompression and multiple carburetion.
* Hydraulic grinds (for approx. 1971 & later engines originally equipped with hydraulic lifters) available on special order.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
111256 256-SUPERCAM 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
111256/262 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
111262 262-SUPERCAM 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
CHEVROLET • 60° — V6 1980-UP • 173 cu. in. engines (2.8L) & (3.IL)
Cast Iron Billet
HYDRAULIC1.5:1 Rocker Ratio
Best overall cam for towing. Trucks, Vans, R.V., etc. Broadtorque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1compr. Computer compatible. Smooth idle.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
SOLID
87
CHEVROLET • 6-Cylinder 1963 and up 292 Truck Engines
RACING CAMS
CHEVROLET • 60° — V6 1980-UP • 173 cu. in. engines (2.8L) & (3.IL)
RACING CAMS
Recommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & MODIFIED VALVE SPRING STEEL POLY VALVE VALVE COMPLETE LIFTERS TIMING SPRINGS SHIMS RETAINERS LOCKS PUSHRODS LOCKS SEALS KIT P/N P. 10-25 GEAR P. 56 P. 27-41 P. 51 P. 42 P. 49 P. 44-48 P. 53 P. 52
290462 202-H 255-TGMQ 205-D # 4 707-ST PL-3/8 293 VL-32 VS-11/32F
290162 202-H 255-TGMQ 205-D # 4 707-ST PL-3/8 293 VL-32 VS-11/32F
290262 202-H 255-TGMQ 205-D # 4 707-ST PL-3/8 293 VL-32 VS-11/32F
290505 202-H 255-TGMQ 6005B # 2 507-ST PL-3/8 293 VL-32 VS-11/32F
290506 202-H 255-TGMQ 6005B # 2 507-ST PL-3/8 293 VL-32 VS-11/32F
290507 202-H 255-TGMQ 6005B # 2 507-ST PL-3/8 293 VL-32 VS-11/32F
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
(12pcs) (12pcs) (12pcs) (12pcs) (12pcs) (24pcs) (12pcs)
Recommended Valve Train Components
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter Q Nose of cam has been grooved for snap ring to prevent gear movement. Gear is supplied FREE with cam.
These items included in Cam & complete kit
CAM & VALVE SPRING STEELCOMPLETE LIFTERS SPRINGS SHIMS RETAINERS KIT P/N P. 10-25 P. 27-41 P. 51 P. 42
110256 222-HY 205-D # 4 707-ST
110256/262 222-HY 205-D # 4 707-ST
110262 222-HY 205-D # 4 707-ST
(12pcs)
(12pcs)
(12pcs)
(12pcs)
(12pcs)
(12pcs)
(12pcs)
(12pcs)
(12pcs)
88
HYDRAULIC ROLLER CAMSHAFTS – STEEL BILLETCHEVROLET 90° V-6—4.3 LITRE — 262 CU. IN. (1987-91)
NOTE: 1987 & LATER 4.3L HYDRAULIC ROLLER CAMS ANDLIFTERS CAN NOT BE INSTALLED IN EARLIER 4.3L ENGINES
CHEVROLET • 90° — V-6 1978 and Up • 200-229 cu. in. (3.8L) Odd-Fire
RACING CAMS1.5:1 Rocker RatioHYDRAULIC
ROLLER
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
101256 256-SUPERCAM 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
101256/262 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
101262 262-SUPERCAM 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
101642 RR-640/60-64 4400-7800 .640 .028 294° 260° 106° ROLLER .640 .028 298° 264°
101648 RR-640/72-76 4800-8200 .640 .028 306° 272° 106° ROLLER .640 .028 310° 276°
Best overall cam for towing. Trucks, Vans, R.V., etc. Broadtorque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1compr. Computer compatible. Smooth idle.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625CFM Carb.
Banked 3/8-1/2 mile asphalt tracks; 9:1 compr.; 390+Carb.For use with 90/150 modified odd-firewith common crank-throws.
Good overall perf. in ASA & ARCA sanctions on 5/8 mileand longer tracks. 9:1 compr.; 390+Carb. for use with90/150 modified odd-fire with common crank-throws.
RACING CAMS
CHEVROLET • 90° — V6 1985-86 • 4.3L (262 cu. in.)
1.5:1 Rocker Ratio
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
121256 256-SUPERCAM 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
121256/262 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
121262 262-SUPERCAM 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
131252
RR-252 1200-4800 .450 .000 252° 204° 112° HYDRAULIC .450 .000 252° 204° ROLLER
131252/257 RR-252/257 1400-5000 .450 .000 252° 204° 112°
HYDRAULIC .465 .000 257° 209° ROLLER
Best overall cam for towing. Trucks, Vans, R.V., etc. Broadtorque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1compr. Computer compatible. Smooth idle.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625CFM Carb.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broadtorque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1compr. Computer compatible. Smooth idle.
Cast Iron Billet
HYDRAULIC
89
HYDRAULIC ROLLER CAMSHAFTS – STEEL BILLETCHEVROLET 90° V-6—4.3 LITRE — 262 CU. IN. (1987-91)
NOTE: 1987 & LATER 4.3L HYDRAULIC ROLLER CAMS ANDLIFTERS CAN NOT BE INSTALLED IN EARLIER 4.3L ENGINES
CAM & VALVE SPRING STEEL POLY VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 53 P. 52
120256 222-HY — 205-D # 4 707-ST PL-3/8 VL-32 VS-11/32F
120256/262 222-HY — 205-D # 4 707-ST PL-3/8 VL-32 VS-11/32F
120262 222-HY — 205-D # 4 707-ST PL-3/8 VL-32 VS-11/32F
130252 � See � See 205-D # 4 707-ST PL-3/8 VL-32 VS-11/32F Below Below
130252/257 � See � See 205-D # 4 707-ST PL-3/8 VL-32 VS-11/32F Below Below
CHEVROLET • 90° — V-6 1978 and Up • 200-229 cu. in. (3.8L) Odd-Fire
CHEVROLET • 90° — V6 1985-86 • 4.3L (262 cu. in.)
RACING CAMSRecommended Valve Train Components
CAM & VALVE SPRING POLY VALVE ALUM. BRONZE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS REV LOCKS LOCKS DIST. GEAR KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 KIT P. 49 P. 53 P. 56
100256 222-HY — 205-D # 4 707-ST — PL-3/8 — —
100256/262 222-HY — 205-D # 4 707-ST — PL-3/8 — —
100262 222-HY — 205-D # 4 707-ST — PL-3/8 — —
100642 1241-LOV6 1235-LG 9205B # 2 91-Ti 100-LRK — VL-700 200-DGS
100648 1241-LOV6 1235-LG 9205B # 2 91-Ti 100-LRK — VL-700 200-DGS
These items included in Cam & complete kit
ST=STEELTI=TITANIUMRETAINERSP. 42-43
(24 pcs)
(12 pcs)
(12 pcs)
(12 pcs)(12 pcs)(12 pcs)(12 pcs)
(12 pcs)(12 pcs)
(12 pcs)(12 pcs)
(12 pcs)(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(24 pcs)
RACING CAMSRecommended Valve Train Components
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads.
� USE LATE MODEL (1987 AND UP) FACTORY HYDRAULIC ROLLER LIFTERS & PUSHRODS WITH ABOVE CAM & ASSEMBLY KITS.
These items included in Cam & complete kit Optional accessories
(24 pcs)(12 pcs) (12 pcs)(12 pcs)(12 pcs) (12 pcs)
(24 pcs)(12 pcs) (12 pcs)(12 pcs)(12 pcs) (12 pcs)
(24 pcs)(12 pcs) (12 pcs)(12 pcs)(12 pcs) (12 pcs)
(24 pcs)(12 pcs) (12 pcs)(12 pcs) (12 pcs)
(24 pcs)(12 pcs) (12 pcs)(12 pcs) (12 pcs)
90
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201256 256-SUPERCAM 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
201258 256-SUPERCAM 1500-4800 .425 .000 256° 202° 108° HYDRAULIC .425 .000 256° 202°
201256/262 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
201262 262-SUPERCAM 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
201262/270-12 262/270 HL 2000-5700 .435 .000 262° 208° 112° HYDRAULIC .445 .000 270° 216°
201264 264-MEGA 2000-5800 .450 .000 264° 214° 108° HYDRAULIC .450 .000 264° 214°
201264/271-12 264/270 MEGA 2000-6000 .450 .000 264° 214° 112° HYDRAULIC .465 .000 270° 221°
201270 270-HL HYD 2000-6000 .445 .000 270° 216° 108° HYDRAULIC .445 .000 270° 216°
201271 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
201271/281-12 270/280 MEGA 2200-6500 .465 .000 270° 221° 112° HYDRAULIC .485 .000 280° 232°
201281 280-MEGA 2500-6800 .485 .000 280° 232° 108° HYDRAULIC .485 .000 280° 232°
201292 292-MEGA 2800-7000 .505 .000 292° 244° 108° HYDRAULIC .505 .000 292° 244°
201304 304-MEGA 3200-7500 .525 .000 304° 256° 108° HYDRAULIC .525 .000 304° 256°
201-TKA TURBOCYCLE-A 1000-5000 .435 .000 262° 208° 114° HYDRAULIC .400 .000 250° 194°
Good all-around performance. Fair idle, Stockconverter, 3.70-4.11 axle ratio. up to 650 CFM Carb.9.5:1 compression.
Best torque & economy in 327-400 C.I. passenger cars &trucks. Max. compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best torque & economy in 305 C.I. 9:1 compr.,passenger cars & trucks. Std. axle ratio, std. to 600CFM Carb. smooth idle.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Excellent performance cam with good vacuum, goodidle. 3.08-3.73 axle ratio, 9.5:1 compr. Up to 650CFM Carb. Computer compatible. Stock converter.
Tremendous torque & good mid-range power.9-10.5:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Excellent mid-range performance. Fair idle. Stockconverter. 9-10.5:1 compr., 3.70-4.11 axle ratio.Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum.3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
High performance use/bracket racing. Lopey idle. 2500Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780CFM Carb.
High performance use/bracket racing. Rough idle. 2800Stall. 10-11:1 compr. 4.11-4.56 axle ratio.Up to 780 CFM Carb.
Ultimate high-performance use/bracket racing. Rough idle.3000 Stall. 11:1 & up compr. 4.33-4.88 axle ratio. Up to850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-CY 4/7, then grind no. and Lobe Center when ordering.
Cast Iron Billet
HYDRAULIC
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
91
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS SET PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 44-48 P. 53 P. 52
200256 CL-201256 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200258 CL-201258 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200256/262 CL-201256/262 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200262 CL-201262 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200262/270-12 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200264 CL-201264 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200264/271-12 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200270 CL-201270 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200271 CL-201271 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200271/281-12 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200281 CL-201281 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200292 CL-201292 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200304 CL-201304 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200-TKA N/A 222-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
A Cam & lifter kits are supplied with 222-HY lifters B Requires cylinder heads be machined with Isky # 568 hole saw F Requires cylinder heads be machined with Isky VST-11/32 cutter
G Compatible with guide plate cylinder heads� Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads
CL201262/270-12
CL201264/271-12
CL201271/281-12
92
CHEVROLET • V-8 265-283-302-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMS1.5:1 Rocker RatioHI-REV SERIES
SOLID LIFTER
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201020 Z-20 2000-6000 .448 .018 268° 228° 112° SOLID .448 .018 268° 228°
201025 Z-25 2500-6500 .480 .018 278° 244° 108° SOLID .480 .018 278° 244°
201027 Z-27 2800-6800 .507 .018 282° 247° 108° SOLID .507 .018 282° 247°
201030 Z-30 3000-7000 .480 .030 290° 250° 108° SOLID .480 .030 290° 250°
201035 Z-35 3000-7500 .525 .016 288° 254° 108° SOLID .525 .016 288° 254°
201506 505-T 3000-7000 .505 .030 290° 254° 108° SOLID .505 .030 290° 254°
201050 Z-50 3500-7500 .507 .028 300° 254° 108° SOLID .507 .028 300° 254°
201060 Z-60 3500-7500 .548 .016 292° 259° 108° SOLID .548 .016 292° 259°
201065 Z-65 4000-8000 .560 .028 314° 272° 108° SOLID .560 .028 314° 272°
201070 Z-70 3500-7500 .548 .028 304° 264° 108° SOLID .548 .028 304° 264°
201075 Z-75 4000-8000 .570 .028 320° 274° 108° SOLID .570 .028 320° 274°
201079 Z-79 4200-8200 .570 .028 320° 274° 108° SOLID .585 .030 330° 284°
201085 Z-85 4500-8500 .585 .030 330° 284° 108° SOLID .585 .030 330° 284°
Mid-range performance. Good idle. Stock converter. 3:70-4:11 axle ratio. Up to 650 CFM Carb. 9:1 compr.
Strong mid-range performance. Lopey idle. 2500 RPM Stall. 3;70-4;11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High performance use/bracket racing. Lopey idle. 3000 Stall. 10.5:1 compr. 3:90-4:11 axle ratio Up to 800 CFM Carb.
High performance. Street/strip. Lopey idle. 2800 Stall. 4:11-4:88 axle ratio. Up to 750 CFM Carb. 10.5:1 Compr.
Bracket racing. Rough idle. 2800 Stall. 4:11-4:56 axle ratio.650-750 CFM Carb. 10:1 compr.
Bracket racing. Rough idle. 3000 Stall. 4:11-4:56 axle ratio.Up to 850 CFM Carb. 10.5:1 compr.
High performance. Street/strip. Lopey idle. 3200 Stall. 4:56-4:88 axle ratio. Up to 800 CFM Carb. 10.5-11:1 compr.
All out competition/drags. 5000 Stall. 5:13-5:57 axle ratio.850+ CFM Carb. 12:1 compr.
Bracket racing. Lopey idle. 4000 Stall. 4:88-5:38 axle ratio.Up to 850 CFM Carb. 11:1 compr.
All out competition/drags. 5000 Stall. 5:13-5:57 axle ratio.850+ CFM Carb. 12:1 compr.
All out competition/drags. 5000 Stall. 5:13-5:57 axle ratio.850+ CFM Carb. 12:1 compr.
All out competition/drags. 5000+ Stall. 5:38-5:86 axle ratio.850+ CFM Carb. 12.5:1 compr.
Great mid-range performance. Lopey idle. 2500 RPM Stall. 3;70-4;11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-C 4/7, then grind no. and Lobe Center when ordering.
93
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & VALVE SPRING STEEL POLY ROCKER VALVE VALVECOMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS ARMS PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 49 P. 44-48 P. 53 P. 52
200020 — 202-H 205-D # 4 707-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200025 — 202-H 205-D # 4 707-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200027 — 202-H 205-D # 4 707-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200030 — 202-H 205-D # 4 707-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200035 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200506 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200050 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200060 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200065 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200070 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200075 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200079 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200085 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
B Requires cylinder heads be machined with Isky #568 hole saw F Requires cylinder heads be machined with VST-11/32 cutter G Compatible with guide plate cylinder heads
94
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 265-283-302-307-327-350-400 cu. in. engines (1957-87) small block
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201252/257
RR-252/257 1200-5000 .450 .000 252° 204° 112° HYDRAULIC .465 .000 257° 209° ROLLER
201257/265
RR-257/265 1400-5600 .465 .000 257° 209° 112° HYDRAULIC .485 .000 265° 217° ROLLER
201265/272
RR-265/272 2000-6000 .485 .000 265° 217° 112° HYDRAULIC .505 .000 272° 225° ROLLER
201272/282
RR-272/282 2500-6400 .505 .000 272° 225° 112° HYDRAULIC .530 .000 282° 234° ROLLER
201282/294
RR-282/294 3000-7000 .530 .000 282° 234° 110° HYDRAULIC .550 .000 294° 246° ROLLER
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650CFM Carb. Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum. 3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio.Up to 780 CFM Carb.
HYDRAULIC
ROLLER
NOTE: 1988-Up 305 & 350 cu. in. engines use a different type of cam core than the 1957-87 engines and therefore cannot be interchanged
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 305-350 cu. in. engines (1988-UP) small block
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
211252/257
RR-252/257 1200-5000 .450 .000 252° 204° 112° HYDRAULIC .465 .000 257° 209° ROLLER
211257/265
RR-257/265 1400-5600 .465 .000 257° 209° 112° HYDRAULIC .485 .000 265° 217° ROLLER
211265/272
RR-265/272 2000-6000 .485 .000 265° 217° 112° HYDRAULIC .505 .000 272° 225° ROLLER
211272/282
RR-272/282 2500-6400 .505 .000 272° 225° 112° HYDRAULIC .530 .000 282° 234° ROLLER
211282/294
RR-282/294 3000-7000 .530 .000 282° 234° 110° HYDRAULIC .550 .000 294° 246° ROLLER
HYDRAULIC
ROLLER
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: 1988-Up 305 & 350 cu. in. engines use a different type of cam core thanthe 1957-87 engines and therefore cannot be interchanged.1992-96 LT-1 & LT-4 engines require a modified “Front End” type cam core.See page 96 for LT-1 listings.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650CFM Carb. Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum. 3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio.Up to 780 CFM Carb.
NOTE: All Isky Hydraulic Roller Cams are compatable with stock cast iron dist. gears.
95
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 265-283-302-307-327-350-400 cu. in. engines (1957-87) small block
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & HYDRAULIC VALVE SPRING STEEL CAM SPROCK. TIMING VALVE COMPLETE ROLLER PUSHRODS SPRINGS SHIMS RETAINERS LOCK PLATE SET LOCKS KIT P/N LIFTERS P. 44-48 P. 27-41 P. 51 P. 42 THRUST BUMP P. 56-57 P. 53 P. 11-14 P.55
200-LP 200252/257 2077HYRT 203HGG 205-D # 4 707-ST 200-TBH 200-TS VL-32 MINUS .460 210-TBI
200-LP 200257/265 2077HYRT 203HGG 205-D # 4 707-ST 200-TBH 200-TS VL-32 MINUS .460 210-TBI
200-LP 200265/272 2077HYRT 203HGG 6105 B #2 507-STA 200-TBH 200-TS VL-32 MINUS .460 210-TBI
200-LP 200272/282 2077HYRT 203HGG 6105 B # 2 507-STA 200-TBH 200-TS VL-32 MINUS .460 210-TBI
200-LP 200282/294 2077HYRT 203HGG 6105 B # 2 507-STA 200-TBH 200-TS VL-32 MINUS .460 210-TBI
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 305-350 cu. in. engines (1988-up) small block
RACING CAMSRecommended Valve Train Components
B Requires cylinder heads be machined with Isky #568 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads.
These items included in Cam & complete kit Optional accessories
CAM & HYDRAULIC VALVE SPRING STEEL BRONZE VALVE VALVECOMPLETE ROLLER PUSHRODS SPRINGS SHIMS RETAINERS DISTR. LOCKS SEALS KIT P/N LIFTERS P. 44-48 P. 27-41 P. 51 P. 42 GEAR P. 53 P. 52 P. 56
210252/257 2030HYRT 203HG 205-D # 4 707-ST 200-DGS VL-32 VS-11/32F
MINUS .580
210257/265 2030HYRT 203HG 205-D # 4 707-ST 200-DGS VL-32 VS-11/32F
MINUS .580
210265/272 2030HYRT 203HG 6105B # 2 507-STA 200-DGS VL-32 VS-11/32F
MINUS .580
210272/282 2030HYRT 203HG 6105B # 2 507-STA 200-DGS VL-32 VS-11/32F
MINUS .580
210282/294 2030HYRT 203HG 6105B # 2 507-STA 200-DGS VL-32 VS-11/32F
MINUS .580
H 1957-77 Motors only I 1978-87 Motors only
96
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 305-350 cu. in. engines LT-1 small block (1992-96)
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
261252/257
RR-252/257 1200-5000 .450 .000 252° 204° 112° HYDRAULIC .465 .000 257° 209° ROLLER
261257/265
RR-257/265 1400-5600 .465 .000 257° 209° 112° HYDRAULIC .485 .000 265° 217° ROLLER
261265/272
RR-265/272 2000-6000 .485 .000 265° 217° 112° HYDRAULIC .505 .000 272° 225° ROLLER
261272/282
RR-272/282 2500-6400 .505 .000 272° 225° 112° HYDRAULIC .530 .000 282° 234° ROLLER
261282/294
RR-282/294 3000-7000 .530 .000 282° 234° 110° HYDRAULIC .550 .000 294° 246° ROLLER
HYDRAULIC
ROLLER
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650CFM Carb. Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum.3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio.Up to 780 CFM Carb.
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 350 cu. in. LS-1 engines (1997 up) small block(Also Vortec 1999-Up 4800-5300, 6000 Series)
RACING CAMS1.7:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
271252/257
RR-252/257 1200-5000 .495 .000 252° 206° 113° HYDRAULIC .510 .000 257° 212° ROLLER
271257/265
RR-257/265 1400-5600 .510 .000 257° 212° 113° HYDRAULIC .530 .000 265° 220° ROLLER
271265/275
RR-265/275 2000-6000 .530 .000 265° 220° 113° HYDRAULIC .550 .000 275° 230° ROLLER
271280/290
RR-280/290 2500-6800 .530 .000 280° 232° 113° HYDRAULIC .540 .000 290° 242° ROLLER
HYDRAULIC
ROLLERNOTE: all cams listed are 3-Bolt mounting style. Single Bolt Mounting style is available on Special Order. Contact Isky factory for single bolt ordering information.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650CFM Carb. Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Excellent mid-range performance. Fair idle. 2500 stall. 3.70-4.00 axle ratio. Up to 10.5:1 compr. Up to 750 CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: All Isky Hydraulic Roller Cams are compatable with stock cast iron dist. gears.
97
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 LT-1 305-350 cu. in. engines (1992--96) small block
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & HYDRAULIC VALVE SPRING STEEL SPRING. VALVECOMPLETE ROLLER PUSHRODS SPRINGS SHIMS RETAINERS LOCATORS LOCKS KIT P/N LIFTERS P. 44-48 P. 27-41 P. 51 P. 42 P. 52 P. 53 260252/257 2030HYRT 203-HGG 235-D # 3 707-STA 255-VSL VL-32 MINUS .580
260257/265 2030HYRT 203-HGG 235-D # 3 707-STA 255-VSL VL-32 MINUS .580 260265/272 2030HYRT 203-HGG 235-D #3 707-STA 255-VSL VL-32 MINUS .580 260272/282 2030HYRT 203-HGG 235-D # 3 707-STA 255-VSL VL-32 MINUS .580
260282/294 2030HYRT 203-HGG 235-D # 3 707-STA 255-VSL VL-32 MINUS .580
CHEVROLET • HYDRAULIC ROLLER CAMSHAFTS–DEEP HARDENED STEEL BILLETV-8 350 cu. in. LS-1 engines (1997 up) small block(Also Vortec 1999-Up 4800-5300, 6000 Series)
RACING CAMSRecommended Valve Train Components
G Compatible with guide plate cylinder heads.
These items included in Cam & complete kit
CAM & HYDRAULIC SPRING VALVE SPRING STEEL VALVECOMPLETE ROLLER PUSHRODS LOCATORS SPRINGS SHIMS RETAINERS LOCKS KIT P/N LIFTERS P. 44-48 P. 52 P. 27-41 P. 51 P. 42 P. 53 270252/257 2030HYRT 203-HGG 175-VSL 165-A # 11 135-ST VL-500 MINUS .380
270257/265 2030HYRT 203-HGG 175-VSL 165-A # 11 135-ST VL-500 MINUS .380
270265/275 2030HYRT 203-HGG 175-VSL 165-A # 11 135-ST VL-500 MINUS .380
270280/290 2030HYRT 203-HGG 175-VSL 165-A # 11 135-ST VL-500 MINUS .380
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve. Use Part # 201-CY 4/7, then grind no. and Lobe Center when ordering.98
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201SL1 SL-1 2000-6500 .390 .000 268° 228° 108° HYDRAULIC .410 .000 272° 232°
201SL2 SL-2 2400-6800 .390 .000 276° 236° 106° HYDRAULIC .410 .000 280° 240°
201LR1 LR-1 2000-6200 .415 .000 264° 224° 107° HYDRAULIC .415 .000 264° 224°
201LR2 LR-2 2400-6600 .415 .000 272° 232° 106° HYDRAULIC .415 .000 272° 232°
201LR3 LR-3 2500-6800 .415 .000 280° 240° 106° HYDRAULIC .415 .000 280° 240°
201LR4 LR-4 3000-7200 .420 .000 296° 248° 105° HYDRAULIC .420 .000 296° 248°
201268 268-MEGA 2000-6400 .450 .000 268° 224° 107° HYDRAULIC .450 .000 268° 224°
201278 278-MEGA 2500-6800 .450 .000 278° 234° 106° HYDRAULIC .450 .000 278° 234°
201288 288-MEGA 2800-7000 .450 .000 288° 244° 106° HYDRAULIC .450 .000 288° 244°
201271 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
201274 274-MEGA 2200-6500 .490 .000 274° 226° 108° HYDRAULIC .490 .000 274° 226°
201281/6 280-MEGA 2500-6800 .485 .000 280° 232° 106° HYDRAULIC .485 .000 280° 232°
201284/6 284 MEGA 2600-6900 .510 .000 284° 236° 106° HYDRAULIC .510 .000 284° 236°
201284/292-6 284/292 MEGA 2700-7000 .510 .000 284° 236° 106° HYDRAULIC .505 .000 292° 244°
201286/6 286 MEGA 2700-7000 .500 .000 286° 240° 106° HYDRAULIC .500 .000 286° 240°
201292/6 292 MEGA 2800-7000 .505 .000 292° 244° 106° HYDRAULIC .505 .000 292° 244°
201292/296-6 292/296 MEGA 2900-7100 .505 .000 292° 244° 106° HYDRAULIC .530 .000 296° 248°
201296/6 296-MEGA 3000-7200 .530 .000 296° 248° 106° HYDRAULIC .530 .000 296° 248°
201296/304-6 296/304-MEGA 3200-7400 .530 .000 296° 248° 106° HYDRAULIC .525 .000 304° 256°
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
Sportsman classes; 3/8-1/2 mile banked tracks.Any carburetor.
Sportsman classes; 3/8-1/2 mile banked tracks whenusing stock exhaust manifolds. Any carburetor.
Sportsman classes;1/2 mile high banked track.Any carburetor.
Sportsman classes;1/2 mile high banked track whenusing stock exhaust manifolds. Any carburetor.
Cast Iron Billet
HYDRAULIC
OVAL TRACK
Classes where stock lift rules apply; 1/4-3/8 miletracks with slight bank.
Classes where stock lift rules apply; banked3/8-1/2 mile tracks.
.420” lift rule class; 1/4-3/8 mile tracks with slight bank.
.420” lift rule class; banked1/4-3/8 mile tracks.
.420” lift rule class; banked 3/8-1/2 mile tracks.
.420” lift rule class; high banked1/2 mile tracks.
.450” lift rule class; 1/4-3/8 mile tracks with slight bank.
.450” lift rule class; banked 1/4-3/8 mile tracks.
.450” lift rule class; high banked 3/8-1/2 mile tracks.
Hobby stock & street stock classes; 1/4-3/8 mile trackswith slight bank. 2BBL carburetor.
Hobby stock & street stock classes; 1/4-3/8 mile trackswith slight bank. 2BBL carburetor.
Hobby stock & street stock classes; banked1/4-3/8 miletracks. Any carburetor.
Street stock & sportsman classes; banked 3/8-1/2 miletracks. Any carburetor.
Sportsman classes; 3/8-1/2 mile banked tracks whenusing stock exhaust manifolds. Any carburetor.
.500” lift rule class; banked 3/8-1/2 mile tracks.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
99
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS SET PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 44-48 P. 53 P. 52
200SL1 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200SL2 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200LR1 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200LR2 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200LR3 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200LR4 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200268 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200278 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200288 — 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200271 CL-201271 202-HY 205-D # 4 707-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200274 CL-201274 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200281/6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200284/6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200284/292-6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200286/6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200292/6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200292/296-6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200296/6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
200296/304-6 — 202-HY 6005B # 2 507-ST PL-3/8 300-TS � 203-HGG VL-32 VS-11/32F
A Cam & lifter kits are supplied with 222-HY LIFTERS B Requires cylinder heads be machined with Isky #568 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter
G Compatible with guide plate cylinder heads.� Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads
100
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201524 524 2400-6600 .524 .016 278° 244° 106° SOLID .534 .018 282° 248°
201525 525-A 2600-6800 .507 .016 282° 247° 106° SOLID .525 .018 288° 254°
201534 534-A 2600-6800 .534 .016 282° 248° 106° SOLID .525 .018 288° 254°
201526 525-B 3000-7000 .525 .016 288° 254° 106° SOLID .548 .018 292° 259°
201547 547-A 3000-7000 .547 .016 288° 254° 106° SOLID .548 .018 292° 259°
201527 525-C 3200-7200 .525 .016 288° 254° 106° SOLID .555 .016 296° 263°
201549 547-B 3000-7200 .547 .016 288° 258° 106° SOLID .555 .016 296° 263°
201548 548 3400-7400 .548 .016 292° 259° 106° SOLID .555 .016 296° 263°
201555 555 3600-7600 .555 .016 296° 263° 106° SOLID .560 .016 302° 268°
201561 561 3800-8000 .560 .016 302° 268° 106° SOLID .570 .016 306° 272°
201CC1 CC1 3000-6800 .525 .016 290° 254° 106° MECHANICAL .520 .018 296° 260°
201CC2 CC2 3200-7000 .525 .016 290° 254° 106° MECHANICAL .545 .026 304° 264°
201506 505-T 3000-7000 .505 .030 290° 254° 108° SOLID .505 .030 290° 254°
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSHI-REV SERIES
SOLID LIFTER1.5:1 Rocker Ratio
OVAL TRACK
1/4-3/8 mile tracks with little or no bank. 2-BBL Carb.
1/4-3/8 mile tracks with little or no bank. 4-BBL Carb.
1/4-3/8 mile tracks with little or no bank. 2-BBL Carb.
Banked 1/4-3/8 mile tracks. 4-BBL Carb.
Banked 1/4-3/8 mile tracks. Any carburetor.
Banked 1/2 mile track. 4-BBL Carb.
Banked 3/8-1/2 mile tracks. Very broad power range.Any carburetor.
High bank 1/2 mile track; 4-BBL Carb.
High bank 1/2 mile track; 4-BBL Carb.
Road racing. 4-BBL Carb.
Ideal for IMCA & Wissota modified classes. Broad powerband on banked 1/4-3/8 mile tracks. 2-BBL Carb.
Ideal for IMCA & Wissota modified classes. Best onfaster tracks (Banked 3/8-1/2 mile). Any carburetor.
Ideal for IMCA & Wissota modified classes. 2-BBL Carb. Banked 1/4-3/8 mile tracks.
SPECIAL NOTE: Extra Hard “ Proferral 55” (R/c 55) Cam Cores for maximum cam life, are available on a special order basis.To order, specify - 201-CP55 along with Grind Number & Lobe Center.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-C 4/7, then grind no. and Lobe Center when ordering.
101
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY ROCKER VALVE VALVE COMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS ARMS PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 49 P. 44-48 P. 53 P. 52
200524 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200525 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200534 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200526 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200547 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200527 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200549 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200548 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200555 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200561 — 202-H 6105B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
200CC1 — 202-H 235-D # 4 707-STA PL-3/8 204 203-HGG VL-32 VS-11/32F
200CC2 — 202-H 235-D # 4 707-STA PL-3/8 204 203-HGG VL-32 VS-11/32F
200506 — 202-H 6005B # 2 507-ST PL-3/8 204 203-HGG VL-32 VS-11/32F
B Requires cylinder heads be machined with Isky #568 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads.
102
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMS1.5:1 Rocker Ratio - OVAL TRACK
NEW MAGNUM-XL SOLID AND ACCELERATOR INTAKE ROLLER PROFILES (P/N 201652 & 201653)
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201530 530/242 MECH 2300-6500 .530 .014 270° 242° 108° SOLID .530 .016 270° 242°
201535 535/246 MECH 2400-6600 .535 .014 274° 246° 108° SOLID .535 .016 274° 246°
201544 545/250 MECH 2500-6700 .545 .014 278° 250° 108° SOLID .545 .016 278° 250°
201554 555/254 MECH 2600-6800 .555 .014 282° 254° 108° SOLID .555 .016 282° 254°
201532 530-A MECH 2300-6600 .530 .014 270° 242° 106° SOLID .535 .016 274° 246°
201536 535-A MECH 2400-6800 .535 .014 274° 246° 106° SOLID .545 .016 278° 250°
201546 545-A MECH 2600-7000 .545 .014 278° 250° 106° SOLID .555 .016 282° 254°
201556 555-A MECH 2800-7200 .555 .014 282° 254° 106° SOLID .565 .016 286° 258°
201571 570-A MECH 3000-7600 .570 .014 286° 258° 106° SOLID .580 .016 290° 262°
201581 580-A MECH 3200-7800 .580 .014 290° 262° 106° SOLID .585 .016 294° 266°
201615 RR-615 3500-7500 .615 .028 294° 260° 106° ROLLER .617 .028 302° 268°
*201652 RR-652 3800-7400 .650 .024 286° 256° 106° ROLLER .645 .028 298° 264°
*201653 RR-653 4000-7600 .650 .024 290° 260° 106° ROLLER .645 .028 302° 268°
Single pattern/overlap reduced for restricted intakeclasses (Late model stock) 1/4 mile track/long rodapplications.
Single pattern/overlap reduced for restricted intakeclasses (Late model stock) 3/8 mile track/long rodapplications.
Single pattern/overlap reduced for restricted intakeclasses (Late model stock) 1/2-5/8 mile track/longrod applications.
Banked 1/4-3/8 mile tracks/5.7-5.85” rod length.
Banked 3/8-1/2 mile tracks/5.7-5.85” rod length.
High Banked 3/8-1/2 mile oval, 5.7-5.85" rod length
High Banked 1/2 mile oval, 5.7-5.85" rod length
High Banked 1/2-5/8 mile oval, 5.7-5.85" rod length
Good overall perf. on 3/8-1/2 mile banked tracks.Compression motors. 4-BBL Carb., easy on valve train.
Ultimate performance on 1/4-3/8 mile tracks; Plenty oftorque off corners with excellent power down thestraights. Compression motors. Any carb.
Ultimate performance on 3/8-1/2 mile tracks; Plenty oftorque off corners with excellent power down thestraights. Compression motors. Any carb.
Single pattern/overlap reduced for restricted intakeclasses (Late model stock) 1/4 mile track/long rodapplications.
1/4-3/8 mile tracks with little or no bank,5.7-5.85” rod length.
SPECIAL NOTE: Extra Hard “Proferral 55” (R/c 55) Solid Cam Cores for maximum cam life, are available on a special order basis.To order, specify - 201-CP55 along with Grind Number & Lobe Center.
*Also available for 360 cu. in. Sprint Application with rear accessory drive. Simply add “RAD” to end of part number: i.e. - 201652RAD or 201653RAD.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
SOLID
ROLLER
103
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit
CAM & CAM & A VALVE SPRING STEEL REV THRUST CAM SPROCKET ALUM BRONZE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS KIT BUMPER LOCKS PLATE DIST GEAR KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 54 P. 55 P. 55 P. 56
200530 202H — 6105B # 2 507-ST — — — —
200535 202H — 6105B # 2 507-ST — — — —
200544 202H — 6105B # 2 507-ST — — — —
200554 202H — 6105B # 2 507-ST — — — —
200532 202H — 6105B # 2 507-ST — — — —
200536 202H — 6105B # 2 507-ST — — — —
200546 202H — 6105B # 2 507-ST — — — —
200556 202H — 6105B # 2 507-ST — — — —
200571 202H — 6105B # 2 507-ST — — — —
200581 202H — 6105B # 2 507-ST — — — —
200615 272RH 203HGG 9365R # 2 527-STA 210LRK 200-TB H 200-LP 200-DGS
210-TBI
200652 272RH 203HGG 9365R # 2 527-STA 210LRK 200-TB H 200-LP 200-DGS
210-TBI
200653 272RH 203HGG 9365R # 2 527-STA 210LRK 200-TB H 200-LP 200-DGS
210-TB I
B Requires cylinder heads be machined with Isky #568 Hole Saw G Compatible with guide plate cylinder heads. H 1955-77 Motors only
I 1978 & up motors with shallow timing cover R Requires cylinder heads be machind with Isky #3608 Hole Saw.
CHEVROLET CYLINDER HEADS � 1970-73 Z-28, LT-1 AND ANGLE PLUG � CYLINDER HEAD WARNING1970-73 Chevy cylinder heads of the Z-28 — 302, 327 and 350 cubic inch series came through from the factory three pounds lighter than previous cylinder heads. Unfortunately, a lot ofmetal has been removed from the spring seat area and anyone hollow-milling or hole-sawing for larger springs is almost certain to cut through into the water jacket and ruin the heads. Theexhaust valve spring seats at each end of the head are the most prone to break through.We recommend that you do NOT use these cylinder heads with a spring diameter larger than 11/2-inches. Use instead our standard 1.435 O.D. 6105 OR 6205 springs. To safely enlarge thespring-seats for either of the above spring combinations, use our special stepped hole saw #568 and instructions to prevent cutting into Z-28 water jacket when opening up spring seats.
104
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMS
Valve Valve ADV. .050 �Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201640 RR-640/56-60 3800-7200 .640 .028 290° 256° 106° ROLLER .640 .028 294° 260°
201641 RR-640/56-64 4000-7200 .640 .028 290° 256° 106° ROLLER .640 .028 298° 264°
201642 RR-640/60-64 4100-7300 .640 .028 294° 260° 106° ROLLER .640 .028 298° 264°
201654 RR-645/60-64 3800-7200 .645 .028 294° 260° 104° ROLLER .645 .028 298° 264°
201643 RR-640/60-68 4200-7400 .640 .028 294° 260° 106° ROLLER .640 .028 302° 268°
201643RAD RR-645/60-68 4200-7400 .645 .028 294° 260° 106° ROLLER .645 .028 302° 268°
201644 RR-640/64-68 4300-7400 .640 .028 298° 264° 106° ROLLER .640 .028 302° 268°
201645 RR-640/64-72 4400-7500 .640 .028 298° 264° 106° ROLLER .640 .028 306° 272°
201646 RR-640/68-72 4500-7500 .640 .028 302° 268° 106° ROLLER .640 .028 306° 272°
201647 RR-640/68-76 4500-7600 .640 .028 302° 268° 106° ROLLER .640 .028 310° 276°
201648 RR-640/72-76 4500-7600 .640 .028 306° 272° 106° ROLLER .640 .028 310° 276°
201649 RR-640/72-80 4500-7700 .640 .028 306° 272° 106° ROLLER .640 .028 314° 280°
201655 RR-640/76-80 4500-7700 .640 .028 310° 276° 106° ROLLER .640 .028 314° 280°
201656 RR-640/76-82 4600-7800 .640 .028 310° 276° 106° ROLLER .640 .028 318° 282°
ROLLERSERIES
Steel Billet
1.5:1 Rocker Ratio
OVAL TRACK
Flat 1/4-3/8 mile asphalt tracks; 9-1 compr.; 390+Carb.
1/4-3/8 mile dirt tracks with little banking; Compressionmotors. 390+Carburetion.
Banked 3/8-1/2 mile asphalt tracks; 9-1 compr; 390+Carb.
Banked 1/4-3/8 mile asphalt tracks; 9-1 compr; 390+Carb.
Banked 3/8-1/2 mile dirt or asphalt tracks; Compressionmotors; 390+Carb.
Best overall perf. in 360 C.I. Sprint motors. Very broadpower band. Rear of cam is drilled & tapped to acceptsander rear accessory drive.
High banked 3/8-1/2 mile asphalt tracks (All pro. circuit).Excellent mid to upper end power. 9-1 compr. 390+Carb.
Banked 1/2-5/8 mile dirt or asphalt tracks. Compressionmotors; 390+Carb. Also good perf. in 400 cu. in. sprintapplications as well. (Use P/N 201645 RAD)
Banked 5/8 mile dirt or asphalt tracks. Compression motors; 650+Carb. Good overall perf. in champ. dirt cars.
Banked 5/8 mile dirt or asphalt tracks. Compression motors; 650+Carb. Good overall perf. in champ. dirt cars.
Road race applications. Broad power band.Under 350 C.I.
Road race applications. Broad power band. 350 C.I.and above.
High RPM road racing. 350+C.I.
High RPM road racing. 350+C.I.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-RR 4/7, then grind no. and Lobe Center when ordering. Specify bearing size also.
105
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit
�CAM & ROLLER VALVE SPRING STEEL REV THRUST CAM SPROCKET ALUM BRONZE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS KIT BUMPER LOCKS PLATE DIST GEAR KIT P/N P. 15-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 54 P. 55 P. 55 P. 56
200640 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200641 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200642 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200654 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200643 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200643RAD 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200644 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200645 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200646 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200647 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200648 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200649 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200655 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200656 272RH 203HGG 9315R # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
G Compatible with guide plate cylinder heads. H 1955-77 Motors only
I 1978 & up motors with shallow timing cover R Requires cylinder heads be machind with Isky #3608 Hole Saw.
106
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSROLLERSERIES
Steel Billet
1.5:1 Rocker Ratio
OVAL TRACK
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-RR 4/7, then grind no. and Lobe Center when ordering. Specify bearing size also.
Valve Valve ADV. .050 �Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201490 RR-490 2200-6000 .485 .024 278° 234° 108° ROLLER .495 .028 284° 242°
201520 RR-520 2400-6200 .525 .020 280° 240° 108° ROLLER .525 .020 280° 240°
201575 RR-575 2600-6500 .576 .028 284° 244° 108° ROLLER .576 .028 284° 244°
201570 RR-570-T 3000-7000 .570 .028 290° 250° 108° ROLLER .570 .028 290° 250°
201602 RR-602 3500-7500 .602 .028 300° 260° 108° ROLLER .602 .028 300° 260°
201675 RR-675 4000-8000 .675 .024 308° 264° 108° ROLLER .630 .028 314° 272°
201600 RR-600 4500-8500 .588 .028 320° 280° 108° ROLLER .588 .028 320° 280°
201630 RR-630 4000-8000 .630 .028 314° 272° 108° ROLLER .630 .028 314° 272°
201631 RR-630-A 4200-8300 .630 .028 314° 272° 108° ROLLER .630 .028 322° 280°
201670 RR-641-A 4400-8000 .641 .028 306° 272° 104° ROLLER .641 .028 306° 272°
201671 RR-641-B 4600-8000 .641 .028 310° 276° 106° ROLLER .641 .028 310° 276°
201672 RR-641-C 4600-8000 .641 .028 310° 276° 104° ROLLER .641 .028 314° 280°
Strong low-end perf. Fair idle. 2500 stall. 3.55-3.90axle ratio. 10-11:1 compr. Up to 680 CFM Carb.
Strong low-end perf. Fair idle. 2500 stall. 3.55-3.90axle ratio. 10-11:1 compr. Up to 680 CFM Carb.
Good mid-range perf. Rough idle. 2500 stall. 3.90-4.10axle ratio. 10-11:1 compr. Up to 750 CFM Carb.
Good mid-range perf. Lopey idle. 2800 stall. 4.10-4.56axle ratio. 10-11:1 compr. Up to 780 CFM Carb.
Good cam for 3500LB bracket racing “drags”. 3000 stall.4.56-4.88 axle ratio. 11-12:1 compr. Up to 800 CFM Carb.
Good mid-range perf. for heavy bracket racing “drags”.3500-4000 stall. 4.56-5.13 axle ratio. 11-12:1 compr. Up to 850 CFM Carb.
Moderate lift, top end power cam. Great for nostalgiadrags. 4500-5000 stall. 5.38-5.57 axle ratio. High compression. 850 CFM Carb.
Good all around perf. for bracket racing. 4000-4500 stall.4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Good all around perf. for bracket racing. 4000-4500 stall.4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Super stock automatic: 265 cu. in. 4500-5000 stall.5.13-5.57 axle ratio. High compr.
Super stock, 4 speed: 265 cu. in. 5.38 axle ratio.High compr.
Super stock, automatic: 283 cu. in. 4500-5000 stall.5.38-5.57 axle ratio. High compr.
107
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit
�CAM & ROLLER VALVE SPRING STEEL REV THRUST CAM SPROCKET ALUM BRONZE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS KIT BUMPER LOCKS PLATE DIST GEAR KIT P/N P. 15-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 54 P. 55 P. 55 P. 56
200490 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200520 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200575 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200570 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200602 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200675 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200600 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200630 272RH 203HGG 9315BB # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200631 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200670 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200671 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200672 272RH 203HGG 9315B # 2 527-STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
B Requires cylinder heads be machined with Isky #568 Hole Saw G Compatible with guide plate cylinder heads. H 1955-77 Motors only
I 1978 & up motors with shallow timing cover R Requires cylinder heads be machind with Isky #3608 Hole Saw.
WARNINGLate model cylinder heads 1970 & Up with pushrod guide plates, require the use of special hardened pushrods, to prevent pushrod wear.
USE THE FOLLOWINGFor Flat Tappet Cams ..... #203-HG • For Roller Cams (#272-RH Tappet) ..... #203-HG
NOTE: Do not attempt to use our standard 203 pushrods as they will be ruined by rubbing against the hardened guide plates.
108
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMS1.5:1 Rocker RatioSTEELBILLETROLLER
Valve Valve ADV. .050 �Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
201673 RR-641-D 4800-8200 .641 .028 314° 280° 104° ROLLER .641 .028 320° 286°
201674 RR-641-E 4800-8200 .641 .028 318° 282° 104° ROLLER .641 .028 320° 286°
201660 RR-660 4500-8500 .660 .028 324° 282° 108° ROLLER .660 .028 324° 282°
201662 RR-662 5000-9000 .662 .028 332° 286° 108° ROLLER .662 .028 332° 286°
201665 RR-665 4800-8800 .660 .028 324° 282° 108° ROLLER .662 .028 332° 286°
201718 RR-718 4500-8500 .718 .024 318° 274° 108° ROLLER .660 .028 324° 282°
201735 RR-735 4500-8800 .735 .026 322° 278° 108° ROLLER .685 .028 332° 286°
201663 RR-664-A 5000-8500 .664 .028 314° 282° 106° ROLLER .664 .028 318° 286°
201664 RR-664-B 5000-8700 .664 .028 314° 282° 106° ROLLER .630 .028 322° 290°
201685 RR-685 5000-9000 .685 .028 332° 286° 108° ROLLER .685 .030 336° 292°
201686 RR-685-A 5000-9000 .685 .028 332° 286° 108° ROLLER .654 .030 336° 292°
Super stock, 4-speed: 283 cu. in. 5.86 axle ratio. High compr.
Super stock, automatic: 327,350 cu. in. 5000+stall. 5.38 axle ratio. High compr.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM.
Good all-around perf. in super-gas & super comp. 5000+ stall. 5.57-5.86 axle ratio. High compr. 850+CFM.
Good all-around perf. in super-gas & super comp. 5000+ stall. 5.57-5.86 axle ratio. High compr. 850+CFM.
Good all-around perf. for super-comp. 4500+stall. 5.38-5.86 axle ratio. High compr. Tunnel Ram manifoldwith 2 carburetors.
Good all-around perf. for super-comp. 4500+stall. 5.38-5.86 axle ratio. High compr. Tunnel Ram manifoldwith 2 carburetors.
Super stock, 4-speed: 327 C.I. 5.86 axle ratio. High compr.
Super stock, 4-speed: 350 C.I. 5.86 axle ratio. High compr.
Comp. eliminator, super-comp drags. 5000+stall. 5.86-6.14 axle ratio. High compr. Tunnel ram manifoldwith 2 carburetors.
Comp. eliminator, super-comp drags. 5000+stall. 5.86-6.14 axle ratio. High compr. Tunnel ram manifoldwith 2 carburetors.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 201-RR 4/7, then grind no. and Lobe Center when ordering. Specify bearing size also.
109
CHEVROLET • V-8 265-283-302-305-307-327-350-400 cu. in. engines (SMALL BLOCK) (1957-87)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit
�CAM & ROLLER VALVE SPRING STEEL REV THRUST CAM SPROCKET ALUM BRONZE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS KIT BUMPER LOCKS PLATE DIST GEAR KIT P/N P. 15-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 54 P. 55 P. 55 P. 56
200673 272RH 203HGG 9315R # 2 527STA 210-LRK 200-TBH 200-LP 200- DGS
210-TB I
200674 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200660 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200662 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200665 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200718 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200735 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200663 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200664 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200685 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
200686 272RH 203HGG 9315R # 2 527STA 210LRK 200-TBH 200-LP 200- DGS
210-TB I
G Compatible with guide plate cylinder heads. H 1955-77 Motors only
I 1978 & up motors with shallow timing cover R Requires cylinder heads be machind with Isky #3608 Hole Saw.
1974 AND UP CHEVROLET CYLINDER HEADS1974 PART NO. 340292 • 1975 PART NO. 3965784 & STANDARD ANGLE PLUG
Part No. 304292 and 3965784 heads are competition only “Off-Road” racing cylinder heads, introduced by Chevrolet.
Both these and the standard 1974 angle plug heads come from the factory with large 1.450" dia. spring seats and therefore require no additional hole-sawing toinstall our 6005, 6105 and 6205 springs. The 9005, 9265, 9315 and 9365 springs require machining with our #3608 holesaw.
110
CHEVROLET • V-8 396-402-427-454 cu. in. engines (BIG BLOCK) (1967-95)
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
396256 256-SUPERCAM 1500-4800 .490 .000 256° 202° 112° HYDRAULIC .490 .000 256° 202°
396256/262 256/262 1800-5000 .490 .000 256° 202° 110° HYDRAULIC .488 .000 262° 208°
396262 262-SUPERCAM 2000-5500 .488 .000 262° 208° 108° HYDRAULIC .488 .000 262° 208°
396264 264-MEGA 2000-5800 .525 .000 264° 214° 108° HYDRAULIC .525 .000 264° 214°
396270 270-HL 2000-6000 .510 .000 270° 216° 114° HYDRAULIC .510 .000 270° 216°
396271 270-MEGA 2000-6200 .542 .000 270° 221° 108° HYDRAULIC .542 .000 270° 221°
396271/281-14 270/280 MEGA 2200-6500 .542 .000 270° 221° 114° HYDRAULIC .565 .000 280° 232°
396286 286 2500-6500 .510 .000 286° 224° 108° HYDRAULIC .510 .000 286° 224*
396296 296 2500-6500 .510 .000 296° 234° 114° HYDRAULIC .510 .000 296° 234°
396281 280-MEGA 2500-6800 .565 .000 280° 232° 108° HYDRAULIC .565 .000 280° 232°
396282 280-MEGA 2500-6800 .565 .000 280° 232° 110° HYDRAULIC .565 .000 280° 232°
396292 292-MEGA 2800-7000 .590 .000 292° 244° 108° HYDRAULIC .590 .000 292° 244° 396304 304-MEGA 3200-7500 .612 .000 304° 256° 108° HYDRAULIC .612 .000 304° 256° 396-TA TURBOCYCLE-A 1000-5000 .485 .000 264° 208° 114° HYDRAULIC .455 .000 252° 194°
1.75 :1 Rocker Ratio
Best torque & economy. Passenger cars & trucks. Maximum compr. 9.5:1. Smooth idle. Std. axle ratio. Goodvacuum. Computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing, trucks, vans R.V., etc. Broadtorque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power 9-10.5:1 compr. Good idle. Stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Replacement for factory LS-5 Cam. Good all-aroundperformance. Good idle. Stock converter. 3:36-3:90axle ratio. Up to 750 CFM Carb.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr. 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3:90-4:11 axle ratio. Up to 780 CFM Carb.
High performance use/bracket racing. Good idle. 2800 Stall. 10-11:1 compr. 3:90-4:11 axle ratio. Up to 800 CFM Carb.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3:90-4:11 axle ratio. Up to 780 CFM Carb.
Great performance in Jet-Boat (Marine Use). Lopey idle. 10:1 compr. Up to 800 CFM Carb.
High performance use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4:11-4:56 axle ratio. Up to 780 CFM Carb.
Ultimate high-performance use/bracket racing. Rough idle. 3000 Stall. 11:1 & up compr. 4:33-4:88 axle ratio. Up to 850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Standard axle ratio. Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum.3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
RACING CAMSCast Iron Billet
HYDRAULIC
111
CHEVROLET • V-8 396-402-427-454 cu. in. engines (BIG BLOCK) (1967-95)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS SET PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 44-48 P. 53 P. 52
390256 CL-396256 222-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390256/262 CL-396256/262 222-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390262 CL-396262 222-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390264 CL-396264 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390270 CL-396270 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390271 CL-396271 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390271/281-14 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390286 CL-396286 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390296 CL-396296 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390281 CL-396281 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390282 CL-396282 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390292 CL-396292 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390304 CL-396304 202-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
390-TKA N/A 222-HY 8005-A # 2 347-ST PL-7/16 390-TS 203-96C VL-3/8 VS-3/8F
A Cam & lifter kits are supplied with 222-HY lifters C 3/8 diameter pushrods F Requires cylinder heads be machined with VST-3/8 cutter
CL396271/281-14
112
CHEVROLET • V-8 396-402-427-454 cu. in. engines (BIG BLOCK) (1967-95)
RACING CAMS1.75:1 Rocker RatioHI-REV SERIESSolid Lifter
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve. Use Part No. 396-C4/7, then grind no. and Lobe Center when ordering.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
396266 Z-66 2000-6000 .520 .020 268° 228° 108° SOLID .520 .020 268° 228°
396245 Z-45 2500-6500 .530 .018 278° 244° 108° SOLID .530 .018 278° 244°
396233 Z-33 3000-7000 .560 .030 290° 250° 108° SOLID .560 .030 290° 250°
396255 Z-55 3500-7500 .590 .028 300° 254° 108° SOLID .590 .028 300° 254°
396277 Z-77 4000-7500 .590 .028 310° 264° 108° SOLID .590 .028 310° 264°
396289 Z-89 3500-7500 .630 .028 304° 264° 108° SOLID .630 .028 304° 264°
396288 Z-88 3800-7500 .650 .028 314° 272° 108° SOLID .650 .028 314° 272°
396290 Z-90 4500-7500 .595 .024 314° 264° 110° SOLID .635 .024 334° 274°
396295 Z-95 4500-7500 .665 .030 320° 274° 108° SOLID .665 .030 320° 274°
396297 Z-97 4500-8000 .665 .030 320° 274° 110° SOLID .654 .030 330° 286°
396654 654 4500-8000 .654 .030 330° 286° 108° SOLID .654 .030 330° 286°
Good mid-range power. Fair idle. Stock converter.3:55-3:90 axle ratio. 600-650 CFM Carb. 10:1 compr.
Strong mid-range performance. Lopey idle. 2500 RPM Stall. 3:70-4:11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High performance use/bracket racing. Lopey idle. 3000 Stall. 10.5:1 compr. 3:90-4:11 axle ratio. Up to 800 CFM Carb.
Bracket racing. Rough idle. 3000 Stall. 4:11-4:56 axle ratio. Up to 850 CFM Carb. 10.5:1 compr.
High performance use/bracket racing. Rough idle. 3500 Stall. 4:11-4:56 axle ratio. 11:1 compr. Up to 850 CFM Carb.
Good pulling power for drags in heavy car. Rough idle. 3500 Stall. 4:33-4:56 axle ratio. 11:1 compr. Up to 850 CFM Carb.
All-out drags. 4000-4500 Stall. 4:56-4:88 axle ratio. 850+ CFM Carb. 11.5:1+ compr.
Great performance for marine use V-drive. Rough idle.High compr. 850+ CFM Carb.
All-out drags. 5000 Stall. 4:88-5:13 axle ratio. 850+ CFM Carb. 12:1 compr.
All-out drags. 5000 Stall. 4:88-5:13 axle ratio. 850+ CFM Carb. 12:1 compr.
All-out drags. 5000 Stall. 4:88-5:13 axle ratio. 850+ CFM Carb. 12:1 compr.
113
CHEVROLET • V-8 396-402-427-454 cu. in. engines (BIG BLOCK) (1967-95)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & VALVE SPRING STEEL POLY ROCKER VALVE VALVE COMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS ARM PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 49 � P. 44-48 P. 53 P. 52
390266 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390245 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390233 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390255 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390277 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390289 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390288 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390290 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390295 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390297 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
390654 — 202-H 8005-A # 2 347-ST PL-7/16 204-96 203-96C VL-3/8 VS-3/8F
C 3/8 Diameter pushrods F Requires cylinders heads be machined with VST-3/8 cutter� Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads
114
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMS1.75:1 Rocker RatioSTEELBILLETROLLER
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
396570 RR-570 2600-6200 .565 .024 278° 236° 110° ROLLER .575 .028 284° 244°
396620 RR-620 2800-6400 .620 .030 290° 248° 108° ROLLER .620 .030 290° 248°
396640 RR-640 3200-6800 .640 .028 304° 264° 108° ROLLER .640 .028 304° 264°
396644 RR-644 3600-7200 .640 .028 304° 264° 108° ROLLER .644 .028 310° 270°
396645 RR-645 3400-6800 .640 .028 304° 264° 112° ROLLER .650 .028 318° 272°
396650 RR-650 3500-7200 .650 .028 318° 272° 108° ROLLER .650 .028 318° 272°
396686 RR-686 4500-8000 .686 .028 320° 282° 108° ROLLER .686 .028 320° 282°
396652 RR-652 3800-7500 .650 .028 318° 274° 110° ROLLER .654 .030 330° 286°
396454 RR-654 4500-8000 .654 .030 330° 286° 108° ROLLER .654 .030 330° 286°
396688 RR-688 4500-8200 .686 .028 320° 284° 110° ROLLER .654 .030 330° 286°
396727 RR-727 4500-8500 .727 .030 330° 288° 108° ROLLER .727 .030 330° 288°
396730 RR-730 3800-7500 .730 .028 314° 274° 108° ROLLER .730 .028 314° 274°
396731 RR-730-A 3800-7600 .730 .028 314° 274° 110° ROLLER .730 .028 322° 282°
396732 RR-730-B 4000-8200 .730 .028 322° 282° 110° ROLLER .727 .030 330° 288°
Strong low-mid range perf. Fair idle. 2500+stall. 3.73-4.10 axle ratio. 10.5-11.5:1 compr. 650-750 CFM Carb.
High perf. useage, bracket race drags. 3000 stall. 4.10-4.56 axle ratio. 11-12:1 compr. 780+CFM Carb.
High perf. useage, bracket race drags. 3000 stall. 4.10-4.56 axle ratio. 11-12:1 compr. 780+CFM Carb.
3/8-1/2 mile banked oval track on dirt. 750 CFM Carb.
Pro-Street; Fair idle. 3500 stall. 4:56 axle ratio. 11-12:1 compr. 850+CFM Carb. Also works wellin jet drive, marine: Lake Use.
Bracket Racing. 4000 stall. 4.56-4.88 axle ratio. High compr. 850+CFM Carb.
Excellent choice for super gas competition. 4500 stall. 4.88 axle ratio. High compr. 850+CFM Carb.
Good choice for off-shore marine use. Oval course. High compr. 850+CFM Carb.
Popular super gas cam. 5000 stall. 4.88 axle ratio. High compr. 850+CFM Carb.
Off-shore marine racing, long oval course. High compr. 850+CFM Carb.
Super gas, super comp. drags. 5000 stall. 4.88-5.13 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super Gas: 4500 stall. 4.56-4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super Gas, Super Comp: 4500 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super Gas, Super Comp: 5000 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 396-RR 4/7, then grind no. and Lobe Center when ordering. Specify bearing size also.
115
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMSRecommended Valve Train Components
F Requires cylinder heads machined with VST-3/8 cutterM Steel Retainers
These items included in Cam & complete kit Optional accessories
CAM & ROLLER VALVE SPRING VALVE BRONZE THRUST CAM SPROCKET VALVE VALVECOMPLETE LIFTERS SPRINGS SHIMS RETAINERS LOCKS Dist. Gear BUMPER LOCK PLATE LOCKS SEALS KIT P/N P. 15-25 P. 27-41 P. 51 P. 42 P. 53 P. 56 P. 55 P. 55 P. 53 P. 52
390570 366RHM 9315 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390620 366RHM 9315 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390640 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390644 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390645 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390650 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390686 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390652 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390454 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390688 366RHM 9365 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390727 366RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390730 366RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390731 366RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
390732 366RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8F
116
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMS1.75 :1 Rocker RatioSTEELBILLETROLLER
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
396734 RR-730-C 3800-7800 .730 .028 318° 284° 108° ROLLER .730 .028 320° 288°
396747 RR-747-A 3800-7600 .747 .028 306° 274° 108° ROLLER .730 .028 314° 282°
396748 RR-747-B 3800-7800 .747 .028 314° 282° 108° ROLLER .730 .028 320° 288°
396749 RR-747-C 3800-7800 .747 .028 318° 284° 108° ROLLER .730 .028 320° 288°
396750 RR-747-D 4000-8200 .747 .028 320° 288° 108° ROLLER .730 .028 322° 292°
396770 RR-770 4500-8200 .770 .028 324° 284° 108° ROLLER .770 .028 324° 284°
396772 RR-772 4600-8600 .772 .028 332° 288° 108° ROLLER .772 .028 332° 288°
396774 RR-774 4500-8500 .770 .028 324° 284° 110° ROLLER .772 .028 332° 288°
396775 RR-775 4800-8800 .772 .028 332° 288° 110° ROLLER .763 .028 336° 294°
396798 RR-798 4800-8800 .798 .028 332° 288° 110° ROLLER .798 .028 332° 288°
396799 RR-799 5000-9000 .799 .028 336° 294° 110° ROLLER .799 .028 336° 294°
396800 RR-800-A 5200-9200 .800 .028 332° 288° 114° ROLLER .801 .030 344° 304°
396801 RR-800-B 5500-9500 .800 .028 336° 294° 114° ROLLER .801 .030 344° 304°
396831 RR-831 5600-9600 .831 .028 332° 288° 114° ROLLER .805 .028 350° 310°
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: Special cores are available for swapping cylinders 4 & 7 firing order to obtain a smoother torque curve.Use Part # 396-RR 4/7, then grind no. and Lobe Center when ordering. Specify bearing size also.
Super stock automatic: 427 & 454 cu. in. 4500+stall.4.88-5.13 axle ratio. High compr.
Super stock automatic: 396 cu. in. 4500+stall.4.56-4.88 axle ratio. High compr.
Super stock: 4-speed. 4500+stall. 396 cu. in.4.88-5.13 axle ratio. High compr.
Super stock: 4-speed. 5000+stall. 427 cu. in.4.88-5.13 axle ratio. High compr.
Super stock: 4-speed. 5000+stall. 454 cu. in.4.88-5.13 axle ratio. High compr.
Super gas, super comp. 4500+stall. 4.88 axle ratio.High compr. Tunnel ram intake with 2 carburetors.
Super gas, super comp. 4500+stall. 4.88-5.13 axle ratio.High compr. Tunnel ram intake with 2 carburetors.
Super gas, super comp. 4500+stall. 4.88-5.13 axle ratio.High compr. Tunnel ram intake with 2 carburetors.
Super comp. good choice for nitrous oxide. 4.88-5.13 axle ratio. 5000 stall or lenco. High compr.tunnel ram intake with 2 carburetors.
All-out competition. Comp eliminator. 4.88-5.13 axle ratio.5000 stall or lenco. High compr. tunnel ram intake with 2 carburetors.
All-out competition. Comp eliminator. 4.88-5.13 axle ratio.5000 stall or lenco. High compr. tunnel ram intake with 2 carburetors.
Pro-stock; 500 cu.in./blown alcohol applications; Lenco transmission. High compr. tunnel ram intake with 2 carburetors. 5.13-5.38 axle ratio.
Pro-stock; Mountain motor. Lenco transmission. High compr. tunnel ram intake with 2 carburetors. 5.13-5.38 axle ratio.
500 cu. in. pro-stock; Lenco transmission. High compr. tunnel ram intake with 2 carburetors. 5.13-5.38 axle ratio.
117
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & ROLLER VALVE SPRING VALVE BRONZE THRUST CAM SPROCKET VALVE VALVECOMPLETE LIFTERS SPRINGS SHIMS RETAINERS LOCKS Dist. Gear BUMPER LOCK PLATE LOCKS SEALS KIT P/N P. 15-25 P. 27-41 P. 51 P. 42 P. 53 P. 56 P. 55 P. 55 P. 53 P. 52
390734 366-RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390747 366-RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390748 366-RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390749 366-RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390750 366-RHM 9425 #5 275-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390770 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390772 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390774 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390775 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390798 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390799 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390800 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8Q
390801 372-96-RH 9705R #9/030 375-STM VL-800 200-DGS 200-96-TB 200-LP — VS-3/8R
390831 372-96-RH 9901-AR #9/030 980-TI/10 O VL-10-11/32 200-DGS 200-96-TB 200-LP — VS-11/32 F
F Requires cylinder heads machined with VST-11/32 cutter Q Requires cylinder heads be machined with VST-3/8 cutter R Requires cylinder heads be machined with isky #3708 hole saw
M Steel Retainers O Titanium Retainers
118
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMS1.7:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
396252/257 1200-5000 .495 .000 252° 204° 112° .510 .000 257° 210°
396257/265 1400-5600 .510 .000 257° 210° 112° .530 .000 265° 218°
396265/275 2000-6000 .530 .000 265° 218° 112° .553 .000 275° 228°
396275/284 2500-6400 .553 .000 275° 228° 112° .578 .000 284° 238°
396284/294 3000-7000 .578 .000 284° 238° 110° .608 .000 294° 248°
HYDRAULIC
ROLLER
CHEVROLET • V-8 1996-UP 454-502 cu. in. Gen 6 Big Block
RACING CAMS
1.7:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
696252/257 1200-5000 .495 .000 252° 204° 112° .510 .000 257° 210°
696257/265 1400-5600 .510 .000 257° 210° 112° .530 .000 265° 218°
696265/275 2000-6000 .530 .000 265° 218° 112° .553 .000 275° 228°
696275/284 2500-6400 .553 .000 275° 228° 112° .578 .000 284° 238°
696284/294 3000-7000 .578 .000 284° 238° 110° .608 .000 294° 248°
HYDRAULIC
ROLLER1996-Up Gen 6 engines when using these camshafts need to be converted to adjustablerocker arms. Use ARP P/N 1357102 rocker arm studs (no machining required) and factoryguide plates. If choosing to stay with stock non-adjustable rocker arms, special lengthpushrods will need to be ordered to obtain correct lifter preload.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: All Isky Hydraulic Roller Cams are compatable with Stock Cast Iron Dist. Gear
RR-265/275HYDRAULICROLLER
RR-275/284HYDRAULICROLLER
RR-284/294HYDRAULICROLLER
RR-257/265HYDRAULICROLLER
RR-252/257HYDRAULICROLLER
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650 CFM Carb.Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Excellent mid-range perf. Fair idle. 2000 stall. 3.70-4.10 axle ratio. Up to 10.5:1 compr. Up to 750 CFM Carb.
High perf. use/bracket racing; off shore marine with I/O drive. Lopey idle. 2500 stall. Up to 11:1 compr. 3.90-4.10 axle ratio. Up to 780 CFM Carb.
RR-265/275HYDRAULICROLLER
RR-275/284HYDRAULICROLLER
RR-284/294HYDRAULICROLLER
RR-257/265HYDRAULICROLLER
RR-252/257HYDRAULICROLLER
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650 CFM Carb. Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Excellent mid-range perf. Fair idle. 2000 stall. 3.70-4.10 axle ratio. Up to 10.5:1 compr.Up to 750 CFM Carb.
High perf. use/bracket racing; off shore marine with I/O drive. Lopey idle. 2500 stall. Up to 11:1 compr. 3.90-4.10 axle ratio. Up to 780 CFM Carb.
119
CHEVROLET • V-8 396-402-427-454 cu. in. engines Big Block V-8 (1967-95)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & HYDRAULIC VALVE SPRING STEEL POLY VALVE VALVE COMPLETE ROLLER PUSHRODS SPRINGS SHIMS RETAINERS LOCKS LOCKS SEALS KIT P/N LIFTERS P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 53 P. 52
390252/257 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
390257/265 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
390265/275 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
390275/284 3977HYRT 8005-A #2 347-ST PL-7/16 VL-3/8 VS-3/8F
390284/294 3977HYRT 8005-A #2 347-ST PL-7/16 VL-3/8 VS-3/8F
CHEVROLET • V-8 1996-UP 454-502 cu. in. Gen 6 Big Block
RACING CAMSRecommended Valve Train Components
THRUSTBUMPER &LOCK PLATE
P. 55
200-96-TB200-LP
200-96-TB200-LP
200-96-TB200-LP
200-96-TB200-LP
200-96-TB200-LP
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
These items included in Cam & complete kit Optional accessories
CAM & HYDRAULIC VALVE SPRING STEEL POLY VALVE VALVE COMPLETE ROLLER PUSHRODS SPRINGS SHIMS RETAINERS LOCKS LOCKS SEALS KIT P/N LIFTERS P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 53 P. 52
690252/257 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
690257/265 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
690265/275 3977HYRT 805-DO #2 347-ST PL-7/16 VL-3/8 VS-3/8F
690275/284 3977HYRT 8005-A #2 347-ST PL-7/16 VL-3/8 VS-3/8F
690284/294 33977HYRT 8005-A #2 347-ST PL-7/16 VL-3/8 VS-3/8F
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
20396C
MINUS 500
C 3/8 Diameter pushrods F Requires cylinder heads be machined with VST-3/8 cutter
120
CHRYS-PLYM-DODGE • “A” ENGINE • V-8 1964-Up 273-340-360 cu. in. engines• 318 cu. in. 1967 & Up
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
3901-M MILE-A-MOR 1000-3800 .400 .000 248° 194° 108° HYDRAULIC .400 .000 248° 194°
3902-M MILE-A-MOR 1000-3800 .375 .000 236° 186° 108° HYDRAULIC .375 .000 236° 186°
390125 256-SUPERCAM 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
390125/26 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
390126 262-SUPERCAM 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
390164 264-MEGA 2000-5800 .450 .000 264° 214° 108° HYDRAULIC .450 .000 264° 214°
390127 270-HL 2000-6000 .445 .000 270° 216° 108° HYDRAULIC .445 .000 270° 216°
390171 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
390128 280-HL 2500-6500 .465 .000 280° 224° 108° HYDRAULIC .465 .000 280° 224°
390181 280-MEGA 2500-6800 .485 .000 280° 232° 108° HYDRAULIC .485 .000 280° 232°
390129 292-MEGA 2800-7000 .505 .000 292° 244° 108° HYDRAULIC .505 .000 292° 244°
390130 300-HL 3000-7000 .485 .000 300° 234° 108° HYDRAULIC .485 .000 300° 234°
390134 304-MEGA 3200-7500 .525 .000 304° 256° 108° HYDRAULIC .525 .000 304° 256°
3901-TA TURBOCYCLE-A 1000-5000 .435 .000 262° 208° 114° HYDRAULIC .400 .000 250° 194°
Mileage & Maximum Lower RPM Torque for 1972 & later(340-360 CI) Low Compression Engines.
Mileage & Maximum Lower RPM Torque for 1972 & later(273-318 CI) Low Compression Engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Tremendous torque & good mid-range power.9-10.5:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio.Up to 650 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio.Up to 780 CFM Carb.
High performance use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4.11-4.56 axle ratio.Up to 780 CFM Carb.
High perf. Street/strip. Lopey idle. 2800 stall. 4.11-4.88 axle ratio. Up to 750 CFM Carb. 10.5:1 compr.
Ultimate high-performance use/bracket racing. Rough idle. 3000 Stall.11:1 & up compr. 4.33-4.88 axle ratio. Up to 850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
121
CHRYS-PLYM-DODGE • “A” ENGINE • V-8 1964-Up 273-340-360 cu. in. engines• 318 cu. in. 1967 & Up
RACING CAMSRecommended Valve Train Components
CAM & CAM & VALVE SPRING STEEL TIMING VALVE VALVE COMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 56-57 P. 53 P. 52
— — 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
— — 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390025 CL-390125 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390025/26 CL-390125/26 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390026 CL-390126 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390064 CL-390164 3912-AHY 3913 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390027 CL-390127 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390071 CL-390171 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390028 CL-390128 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390081 CL-390181 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390029 CL-390129 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390030 CL-390130 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390034 CL-390134 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
3900-TKA — 3912-AHY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
These items included in Cam & complete kit Optional accessories
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-3/8 cutter
� 3913 Pushrods and ADJ. Rocker Arms are mandatory with 270-HL and Hotter cams
122
CHRYS-PLYM • 318 cu. in. 1967 and UpMOPAR-DART-VALIANT-CUDA • V-8 1964 and up 273-340-360 cu. in. engines
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
390171 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
390174 274-MEGA 2200-6500 .490 .000 274° 226° 107° HYDRAULIC .490 .000 274° 226°
390180 280-MEGA 2500-6800 .485 .000 280° 232° 106° HYDRAULIC .485 .000 280° 232°
390184 284-MEGA 2600-6900 .510 .000 284° 236° 106° HYDRAULIC .510 .000 284° 236°
390196 292-MEGA 2800-7000 .505 .000 292° 244° 106° HYDRAULIC .505 .000 292° 244°
390144 E-4 2000-5500 .425 .015 260° 216° 108° SOLID .425 .015 260° 216°
390177 B-777 3000-7000 .480 .018 280° 240° 108° SOLID .480 .018 280° 240°
390157 505-A 3500-7000 .507 .028 300° 254° 108° SOLID .507 .028 300° 254°
390135 Z-35 3000-7000 .525 .016 288° 254° 108° SOLID .525 .018 288° 254°
390155 555 3200-7200 .555 .014 296° 263° 108° SOLID .555 .016 296° 263°
390110 1012-C 4500-8000 .580 .028 312° 274° 104° SOLID .580 .028 312° 274°
RACING CAMS
Cast Iron BilletHYDRAULICSOLID
1.5:1 Rocker Ratio
OVAL TRACK:Hobby stock & street stock classes; 1/4-3/8 mile trackswith slight bank. 2BBL carburetor.
OVAL TRACK:Hobby stock & street stock classes; banked 1/4-3/8 miletracks. Any carburetor.
OVAL TRACK:Hobby stock & street stock classes; banked 1/4-3/8 miletracks. Any carburetor.
OVAL TRACK:Street stock & sportsman classes; banked 3/8-1/2mile tracks. Any carburetor.
OVAL TRACK:Sportsman classes; 3/8-1/2 mile banked tracks. Any carburetor.
Tremendous torque & good mid-range power.9-10:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb.10.5:1 compr.
Bracket racing. Rough idle. 3000 stall. 4.11-4.56 axle ratio. Up to 850 CFM Carb. 10.5:1 compr.
High perf. Street/strip. Lopey idle. 2800 stall. 4.11-4.88 axle ratio. Up to 750 CFM Carb. 10.5:1 compr.
High perf. Street/strip. Lopey idle. 3200 stall.4.56-4.88 axle ratio. Up to 800 CFM Carb.11:1 compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
123
CHRYS-PLYM •
RACING CAMSRecommended Valve Train Components
CAM & CAM & VALVE SPRING STEEL TIMING VALVE VALVE COMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 56-57 P. 53 P. 52
390071 CL-390171 3912-A-HY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390074 — 3912-A-HY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390080 — 3912-A-HY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390084 — 3912-A-HY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390096 — 3912-A-HY 3913� 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390044 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390077 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390057 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390035 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390055 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
390010 — 3102-H 3903 6005 B # 2 3607-ST 3900-TS N/A VS-3/8F
These items included in Cam & complete kit Optional accessories
318 cu. in. 1967 and UpMOPAR-DART-VALIANT-CUDA • V-8 1964 and up 273-340-360 cu. in. engines
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-3/8 cutter
� 3913 Pushrods and ADJ. Rocker Arms are mandatory with 270-HL and Hotter cams
124
CHRYSLER • Specify “Single Bolt” or “Three Bolt” Cam.V-8 1958 and up “B” engines (Wedge-Dodge/Plymouth)Low Block 350-361-383 c.i.High Block 413-426-440 c.i.
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Lift Lash Hot Duration Duration Lobe Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
165125 160125 256-Supercam 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
165125/26 160125/26 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
165126 160126 262-Supercam 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
165164 160164 264-MEGA 2000-5800 .450 .000 264° 214° 108° HYDRAULIC .450 .000 264° 214°
165127 160127 270-HL 2000-6000 .445 .000 270° 216° 108° HYDRAULIC .445 .000 270° 216°
165171 160171 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
165128 160128 280-HL 2500-6500 .465 .000 280° 224° 108° HYDRAULIC .465 .000 280° 224°
165181 160181 280-MEGA 2500-6800 .485 .000 280° 232° 108° HYDRAULIC .485 .000 280° 232°
165130 160130 300-HL 3000-6500 .485 .000 300° 234° 108° HYDRAULIC .485 .000 300° 234°
165129 160129 292-MEGA 2800-7000 .505 .000 292° 244° 108° HYDRAULIC .505 .000 292° 244°
165134 160134 304-MEGA 3200-7500 .525 .000 304° 256° 108° HYDRAULIC .525 .000 304° 256°
1651-TA 1601-TA Turbocycle-A 1000-5000 .435 .000 264° 208° 114° HYDRAULIC .400 .000 252° 194°
1651-TB 1601-TB Turbocycle-B 2000-6000 .440 .000 274° 216° 114° HYDRAULIC .410 .000 260° 200°
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr., good idle, stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter.3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio.Up to 750 CFM Carb. 9.5:1 compr.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
High perf. Street/strip. Lopey idle. 2800 stall. 4.11-4.88 axle ratio. Up to 750 CFM Carb. 10.5:1 compr.
High performance use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4.11-4.56 axle ratio. Up to 780 CFM Carb.
Ultimate high-performance use/bracket racing. Rough idle. 3000 Stall.11:1 & up compr. 4.33-4.88 axle ratio. Up to 850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
High performance turbocharged appl’s. with higher boost.Good idle, stock converter, std. axle ratio. Up to 650 CFM Carb.
Part No.Cam Only
Three SIngle Bolt Bolt
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
125
CHRYSLER • Specify “Single Bolt” or “Three Bolt” Cam.V-8 1958 and up “B” engines (Wedge-Dodge/Plymouth)
Low Block 350-361-383 c.i.High Block 413-426-440 c.i.
RACING CAMSRecommended Valve Train Components
VALVE SPRING STEEL VALVE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS SEALS P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 56 P. 57 P. 52
165025 160025 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165025/26 160025/26 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165026 160026 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165064 160064 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165027 160027 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165071 160071 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165028 160028 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165081 160081 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165030 160030 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165029 160029 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
165034 160034 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
1650-TKA 1600-TKA 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
1650-TKB 1600-TKB 3912-HY 8005-A B # 2 3607-ST 1650-3BK 1600-TS VS-3/8F
These items included in Cam & complete kit Optional accessories
Cam & Complete KitPart No.
Three Bolt Single Bolt
TIMING SET
Three Bolt Single Bolt
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
1613 J
1623 L
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-3/8 cutter J 350-361-383 cu. in. Low Block L 413-426-440 cu. in. High Block
�NOTE: All 1970 and later 440 Six Pack Engines use the new 3-bolt cam sprocket and rollertiming chain which is far superior to the single bolt cam sprocket. We highly recommend the3-bolt conversion for any “B” engine, using the following:1650-3BK — 3-Bolt Conversion Kit (Cam & Crank Sprockets, Roller Chain, & Bolts) All Engines
126
CHRYSLER • Specify “Single Bolt” or “Three Bolt” Cam.V-8 1958 and up “B” engines (Wedge-Dodge/Plymouth)Low Block 350-361-383 c.i.High Block 413-426-440 c.i.
RACING CAMS1.5:1 Rocker Ratio
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Valve Valve ADV. .050 Lift Lash Hot Duration Duration Lobe Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
165177 160177 B-777 2500-6500 .480 .018 280° 240° 108° SOLID .480 .018 280° 240°
165155 160155 505-T 3500-7000 .505 .028 290° 254° 108° SOLID .505 .028 290° 254°
165135 160135 Z-35 3000-7000 .525 .016 288° 254° 108° SOLID .525 .018 288° 254°
165170 160170 Z-70 3500-7500 .548 .028 304° 264° 108° SOLID .548 .028 304° 264°
165175 160175 Z-75 4000-8000 .570 .028 320° 274° 108° SOLID .570 .028 320° 274°
165195 160195 590 4000-7500 .590 .025 320° 282° 104° SOLID .590 .025 320° 282°
165150 N/A RR-505-T 2500-6400 .531 .028 290° 248° 108° ROLLER .531 .028 290° 248°
165160 N/A RR-602 3000-7000 .602 .028 300° 260° 108° ROLLER .602 .028 300° 260°
165163 N/A RR-630 3800-7400 .630 .028 314° 272° 108° ROLLER .630 .028 314° 272°
165162 N/A RR-627 4000-7500 .622 .025 316° 282° 108° ROLLER .588 .025 320° 282°
165166 N/A RR-660 4000-7500 .660 .028 324° 282° 108° ROLLER .660 .028 324° 282°
165165 N/A RR-665 4500-8000 .660 .028 324° 282° 110° ROLLER .662 .028 332° 286°
165176 N/A RR-705 4500-8000 .705 .028 324° 282° 108° ROLLER .705 .028 324° 282°
165173 N/A RR-735 4500-8000 .735 .026 322° 278° 110° ROLLER .685 .028 332° 286°
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
Bracket racing. Rough idle. 2800 stall. 4.11-4.56 axle ratio. 650-750 CFM Carb. 10:1 compr.
High perf. Street/strip. Lopey idle. 2800 stall. 4.11-4.88 axle ratio. Up to 750 CFM Carb. 10.5:1 compr.
Bracket racing. Lopey idle. 4000 stall. 4.88-5.38 axle ratio. Up to 850 CFM Carb. 11:1 compr.
All out competition/drags. 5000 stall. 5.13-5.57 axle ratio. 850+CFM Carb. 12:1 compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
Good mid-range perf. Rough idle. 2500 stall. 3.90-4.10 axle ratio. 10-11:1 compr. Up to 750 CFM Carb.
Good mid-range perf. Lopey idle. 2800 stall. 4.10-4.56 axle ratio. 10-11:1 compr. Up to 780 CFM Carb.
Bracket Racing. 4000 stall. 4.56-4.88 axle ratio. High compr. 850+CFM Carb.
Bracket Racing. 4000 stall. 4.56-4.88 axle ratio. High compr. 850+CFM Carb.
Excellent choice for super gas competition. 4500 stall. 4.88 axle ratio. High compr. 850+CFM Carb.
Super Gas, Super Comp: 4500 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super Gas, Super Comp: 4500 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super Gas, Super Comp: 5000 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Part No.Cam Only
Three Single Bolt Bolt
SOLID
ROLLER
127
CHRYSLER • Specify “Single Bolt” or “Three Bolt” Cam.V-8 1958 and up “B” engines (Wedge-Dodge/Plymouth)
Low Block 350-361-383 c.i.High Block 413-426-440 c.i.
RACING CAMSRecommended Valve Train Components
� VALVE SPRING STEEL THRUST LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS BUMPER P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 55
165077 160077 3102-H 8005-AB # 2 3607-ST —
165055 160055 3102-H 8005-AB # 2 3607-ST —
165035 160035 3102-H 8005-AB # 2 3607-ST —
165070 160070 3102-H 8005-AB # 2 3607-ST —
165075 160075 3102-H 8005-AB # 2 3607-ST —
165095 160095 3102-H 8005-AB # 2 3607-ST —
165050 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165060 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165063 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165062 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165066 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165065 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165076 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
165073 N/A 3672RH 9365 B # 2 3607-ST 4600-TB
These items included in Cam & complete kit
B Requires cylinder heads be machined with Isky #1258 Hole Saw J 350-361-383 cu. in. Low Block L 413-426-440 cu. in. High Block
Cam & Complete KitPart No.
Three Bolt SIngle Bolt
1633A J
1633B L
1633A J
1633B L
1633A J
1633B L
1633A J
1633B L
1633A J
1633B L
1633A J
1633B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
1673A J
1673B L
� USE P/N 1643-A; Heat Treated, Non-ADJ. Pushrods in 426 c.i. Engines. Add 212.00 to the retail price of Cam & Kit when requiring these pushrods.
128
MOPAR • 426 HEMI/KEITH BLACK ALUMINUM/MILODON 7 LITRE/JP-1
CHRYS-HEMI •
RACING CAMS
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
460128 288 3000-7000 .480 .000 288° 240° 108° HYDRAULIC .480 .000 288° 240°
460144 SH-444 3500-7000 .510 .028 300° 254° 108° SOLID .510 .028 300° 254°
460152 SH-520 4000-7500 .534 .028 318° 270° 108° SOLID .534 .028 318° 270°
460159 590 4500-7500 .590 .025 320° 282° 104° SOLID .590 .025 320° 282°
460161 616 4500-7500 .616 .025 314° 282° 104° SOLID .590 .025 320° 282°
460170 RR-700 4000-8200 .716 .028 332° 286° 106° ROLLER .694 .028 332° 286°
460171 RR-770/288 4300-8600 .770 .028 326° 288° 106° ROLLER .745 .028 326° 288°
460180 RR-780/294 4500-8800 .780 .028 334° 294° 106° ROLLER .755 .028 334° 294°
1.57:1 Rocker Ratio INT.1.52:1 Rocker Ratio EX.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
High perf. Use/bracket racing. Lopey idle. 3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio. Up to 800 CFM Carb.
All out drags. 4000-4500 stall. 4.56-4.88 axle ratio. 850+CFM Carb. 11.5:1+compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All-out competition; Single 4-BBL. 4500+stall. 850+CFM Carb. High compr.
Super stock automatic; 5000 stall. 850+CFM Carb. High compr.
Super stock,4-speed; 850+CFM Carb. High compr.
392 cu. in. V-8 #36011957-58 Engines Prefix
Cast Iron BilletHYDRAULICSOLID
1.5:1 Rocker Ratio
New cam cores are now available again! We can custom grind hydraulic and solid lifter camshafts to suit customer’s applications. Kit components such as hydraulic and solid lifters, valve springs, steel retainers, valvelocks and adjustable pushrods are also available. Call the Isky Factory for more information.
354 cu. in. V-8 #30011955-56 Engines Prefix
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
•
HYDRAULIC
SOLID
ROLLER
129
MOPAR • 426 HEMI/KEITH BLACK ALUMINUM/MILODON 7 LITRE/JP-1
RACING CAMSRecommended Valve Train Components
CAM & CAM & VALVE SPRING VALVE THRUST VALVE VALVECOMPLETE LIFTERS LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS BUMPER LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42-43 P. 53 P. 55 P. 53 P. 52
460028 — 3912HY 4103 S 8005-A B # 2 4107-ST M — — VL-5/16 VS-5/16 F
460044 — 3102H 4103 S 8005-A B # 2 4107-ST M — — VL-5/16 VS-5/16 F
460052 — 3102H 4103 S 8005-A B # 2 4107-ST M — — VL-5/16 VS-5/16 F
460059 — 3102H 4103 S 8005-A B # 2 4107-ST M — — VL-5/16 VS-5/16 F
460061 — 3102H 4103 S 8005-A B # 2 4107-ST M — — VL-5/16 VS-5/16 F
460070 — 3672RHM 4203 S 9705 R # 9/030 975-TI O VL-600 4600-TB — VS-5/16 F
460071 — 3672RHM 4203 S 9705 R # 9/030 975-TI O VL-600 4600-TB — VS-5/16 F
460080 — 3672RHM 4203 S 9705 R # 9/030 975-TI O VL-600 4600-TB — VS-5/16 F
These items included in Cam & complete kit Optional accessories
B Requires cylinder heads be machined with Isky #1258 Hole Saw F Requires cylinder heads be machined with VST-5/16 cutterM Steel Retainers
O Titanium Retainers R Requires cylinder heads be machined with Isky #3708 Hole Saw. S 3/8 DIA. Heat Treated Pushrods
130
FORD • 4 CYL. PINTO—CAPRI 1971-73 2000cc OHC Engines
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
451440 440 2000-6000 .442 .010 280° 230° 116° SOLID .442 .010 280° 230°
451465 465 3000-7000 .465 .010 300° 240° 112° SOLID .465 .010 300° 240°
451505 505-B 3600-7500 .510 .010 310° 255° 110° SOLID .510 .010 310° 255°
Cast Iron BilletSOLID LIFTER
1.6:1 Rocker Ratio
Good All-Around Cam for Low-ENDand Mid-Range Power on street.
Good Mid-Range & Top End Camshaft.Manual Transmision; street & strip.
High banked 3/8 mile oval
FORD • MUSTANG-PINTO-CAPRI 4 CYL. 1974-87 2300cc OHC Engines
RACING CAMSCast Iron BilletSOLID LIFTER
1.6:1 Rocker Ratio
OVAL TRACK
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
461465 465 3000-7000 .465 .010 300° 240° 116° SOLID .465 .010 300° 240°
461500 505-A 3200-7200 .500 .010 300° 246° 112° SOLID .500 .010 300° 246°
461505 505-B 3600-7500 .510 .010 310° 255° 110° SOLID .510 .010 310° 255°
461510 510 3400-7800 .510 .010 300° 264° 108° SOLID .510 .010 300° 264°
461511 510 3200-7600 .510 .010 300° 264° 106° SOLID .510 .010 300° 264°
Pony stocks: 1/4-3/8 mile flat oval
Pony stocks: 1/4-3/8 mile banked oval
High banked 3/8 mile oval
3/8-1/2 mile oval, high banked
3/8-1/2 mile oval, medium bank
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
131
FORD • 4 CYL. PINTO—CAPRI 1971-73 2000cc OHC Engines
RACING CAMSRecommended Valve Train Components
CAM & COMPLETE ALUMINUM VALVE SPRINGS KIT P/N RETAINERS P. 27-41
450440 457-AL 455/456 B
450465 457-AL 455/456 B
450505 457-AL 455/456 B
These items included in Cam & complete kit
FORD • MUSTANG-PINTO-CAPRI 4 CYL. 1974-87 2300cc OHC Engines
RACING CAMSRecommended Valve Train Components
CAM & VALVE SPRING STEEL COMPLETE SPRINGS SHIMS RETAINERS KIT P/N P. 27-41 P. 51 P. 42
460465 462-A E 905-D(8) # 2 347-ST(8)
460500 462-A E 905-D(8) # 2 347-ST(8)
460505 462-A E 905-D(8) # 2 347-ST(8)
460510 462-A E 905-D(8) # 2 347-ST(8)
460511 462-A E 905-D(8) # 2 347-ST(8)
These items included in Cam & complete kit
B Requires cylinder heads be machined with Isky #208 Hole Saw E Isky #462-A Lifters are compatible only with solid lifter Camshafts.
SOLIDLIFTERS
132
FORD FALCON - COMET • 6-CYLINDER OHV 144-170-200 cu. in Engines
RACING CAMS1.6:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
321-M MILE-A-MOR 1000-3800 .415 .000 248° 194° 109° HYDRAULIC .415 .000 248° 194°
321256 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
321262 262-Supercam 2000-5500 .445 .000 262° 208° 109° HYDRAULIC .445 .000 262° 208°
321280 280-HL 2500-6500 .465 .000 280° 224° 109° HYDRAULIC .465 .000 280° 224°
321-TA Turbocycle-A 1000-5000 .420 .000 260° 208° 114° HYDRAULIC .390 .000 248° 194°
Mileage & maximum lower RPM torque for late model,low compression (8-9.5:1 max) engines.
Best torque & economy in passenger cars & trucks. Maxcompr., 9.5:1, smooth idle, std. axle ratio, good vacuum,computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
FORD V6 • 1972-UP V6 Engines 2600cc — 2800cc
RACING CAMSCast Iron Billet
SOLIDLIFTER
1.6:1 Rocker Ratio
Valve Valve ADV. .050 Grind No. Lift Lash Hot Duration Duration Lobe UP TO 1983 1984 & UP Type APPLICATION RPM-Range INT. INT. INT. INT. Center 2600cc 2800cc 2800cc EX. EX. EX. EX.
760144 760144 765144 F6-4 2000-5500 .425 .015 260° 216° 109° SOLID .425 .015 260° 216°
760166 760166 765166 F6-66 2500-6300 .448 .018 264° 228° 109° SOLID .448 .018 264° 228°
Tremendous torque & good mid-range power.9-10:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good mid-range power. Fair idle, stockconverter. 3.55-3.90 axle ratio. 600-650CFM Carb. 10:1 compr.
PART NO.CAM ONLY
T T,U
SPECIAL NOTE: 2800cc ENGINESDrill out hold down bolts on oil baffle 1/16" oversizeand shift baffle over for rocker arm and spring clearance.
SPECIAL NOTE: 1984 & later 2800cc ENGINESThe cams in these motors have larger diameter bearingjournals and therefore will not interchange with pre-84' engines.
T,UT
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
133
FORD FALCON - COMET • 6-CYLINDER OHV 144-170-200 cu. in Engines
RACING CAMSRecommended Valve Train Components
CAM & CAM & VALVE SPRING STEEL ADJ. COMPLETE LIFTERS LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS PUSHRODS KIT P/N KIT P/N P 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 44-48
321-MK — 392-HY (12) 303 (12) # 3 327-ST (12) 303-AD (12PCS)
320256 — 392-HY (12) 303 (12) # 3 327-ST (12) 303-AD (12PCS)
320262 — 392-HY (12) 303 (12) # 3 327-ST (12) 303-AD (12PCS)
320280 — 392-HY (12) 303 (12) # 3 327-ST (12) 303-AD (12PCS)
320-TKA — 392-HY (12) 303 (12) # 3 327-ST (12) 303-AD (12PCS)
These items included in Cam & complete kit Optional accessories
1005-W B
206-G (12)
1005-W B
206-G (12)
1005-W B
206-G (12)
1005-W B
206-G (12)
1005-W B
206-G (12)
FORD V6 • 1972-UP V6 Engines 2600cc — 2800cc
RACING CAMSRecommended Valve Train Components
B Requires cylinder heads be machined with Isky #208 Hole Saw D For Engines Equipped with NON-ADJ. Rocker Arms. If Requiring these Pushrods in kit, add $ 120.00 to retail price.
VALVE SPRING STEEL VALVE UP TO 1983 1984 & UP LIFTERS SPRINGS SHIMS RETAINERS LOCKS 2600 cc 2800 cc 2800 cc P. 10-25 P. 27-41 P. 51 P. 42 P. 53
760044 760544 765044 342-H (12) 905-D (12) # 2 4107-ST (12) VL-5/16 (24 PCS)
760066 760566 765066 342-H (12) 905-D (12) # 2 4107-ST (12) VL-5/16 (24 PCS)
These items included in Cam & complete kit
PART NO: CAM AND KIT
134
FORD V6 • 3.8L (232 cu. in.) 1982-87
RACING CAMS1.6:1 Rocker Ratio
Valve Valve ADV. .050 Lift Lash Hot Duration Duration Lobe Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center 1982-83 1984 &up EX. EX. EX. EX.
860125 870125 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
860126 870126 262-Supercam 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
860124 870124 264-MEGA 2200-6000 .480 .000 264° 214° 108° HYDRAULIC .480 .000 264° 214°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, goodvacuum, computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Tremendous torque & good mid-range power.9-10.5:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Part No.Cam Only
FORD - MERC - T-BIRD • (Y - BLOCK) V-8 272-292-312 cu. in. Engines
RACING CAMS1.5:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type Application RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
301444 E-4 2000-5000 .425 .015 260° 216° 108° SOLID .425 .015 260° 216°
301333 RPM-300 2500-5500 .448 .020 270° 228° 112° SOLID .448 .020 270° 228°
301300 F-300 3000-6000 .448 .020 286° 250° 108° SOLID .448 .020 286° 250°
301505 505-T 3500-7000 .505 .028 290° 254° 108° SOLID .505 .028 290° 254°
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Good mid-range power. Fair idle, stock converter.3.55-3.90 axle ratio. 600-650 CFM Carb. 10:1 compr.
Strong mid-range perf. Lopey idle. 2500 RPM stall.3.70-4.11 axle ratio. 650-750 CFM Carb. 10:1 compr.
Bracket racing. Rough idle. 2800 stall. 4.11-4.56 axle ratio.650-750 CFM Carb. 10:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
Cast Iron Billet
SOLID
135
FORD V6 • 3.8L (232 cu. in.) 1982-87
RACING CAMS
FORD - MERC - T-BIRD • (Y - BLOCK) V-8 272-292-312 cu. in. Engines
RACING CAMS
Recommended Valve Train Components
Recommended Valve Train Components
VALVE SPRING STEEL LIFTERS SPRINGS SHIMS RETAINERS 1982-83 1984 & UP P. 10-25 P. 27-41 P. 51 P. 42
860025 870025 432-HY (12) 3105-D (12) U — 347-ST (12) T
860026 870026 432-HY (12) 3105-D (12) U — 347-ST (12) T
860024 870024 432-HY (12) 3105-D (12) U — 347-ST (12) T
These items included in Cam & complete kitCAM & COMPLETE KIT
PART NO.
B Requires cylinder heads be machined with Isky #208 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter
T Must be used with stock multi-groove valve locks U 3105-D installs @ 1.720" with #125 lbs. seat pressure.
CAM & VALVE SPRING STEEL OFFSET VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS CAM KEY LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 (8°) P. 53 P. 52
300444 302-H 303 6005 B # 2 507-ST OFK - E 8 VL-32 VS-11/32 F
300333 302-H 303 6005 B # 2 507-ST OFK - E 8 VL-32 VS-11/32 F
300300 302-H 303 6005 B # 2 507-ST OFK - E 8 VL-32 VS-11/32 F
300505 302-H 303 6005 B # 2 507-ST OFK - E 8 VL-32 VS-11/32 F
These items included in Cam & complete kit Optional accessories
136
FORD • (Standard Gear-Drive from Factory) 6-CYLINDER 1965-and up OHV 240-300 cu. in. Engines
RACING CAMS1.6:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type Application RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
331-M MILE-A-MOR 1000-3800 .415 .000 248° 194° 108° HYDRAULIC .415 .000 248° 194°
331256 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
331262 262-Supercam 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
331280 280 2500-6500 .465 .000 280° 224° 109° HYDRAULIC .465 .000 280° 224°
331-TA Turbocycle-A 1000-5000 .445 .000 262° 208° 114° HYDRAULIC .415 .000 250° 194°
FORD • — FALCON • MUSTANG • MAVERICK 6 Cyl. 250 cu. in Engines
RACING CAMS1.6:1 Rocker Ratio
Mileage & maximum lower RPM torque for late model,low compression (8-9.5:1 max) engines.
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
321A-M MILE-A-MOR 1000-3800 .415 .000 248° 194° 108° HYDRAULIC .415 .000 248° 194°
321255 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
321266 262-Supercam 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
321288 280 2500-6500 .465 .000 280° 224° 109° HYDRAULIC .465 .000 280° 224°
Mileage & maximum lower RPM torque for late model,low compression (8-9.5:1 max) engines.
Best torque & economy in passenger cars & trucks.Max compr., 9.5:1, smooth idle, std. axle ratio, goodvacuum, computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
Cast Iron Billet
HYDRAULIC
137
FORD • (Standard Gear-Drive from Factory) 6-CYLINDER 1965-and up OHV 240-300 cu. in. Engines
RACING CAMSRecommended Valve Train Components
CAM & VALVE SPRING STEEL VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 53 P. 52
331-MK 432-HY (12) 333 6005 B (12) # 2 507-ST (12) VL-32 (24) VS-11/32 F (12)
330256 432-HY (12) 333 6005 B (12) # 2 507-ST (12) VL-32 (24) VS-11/32 F (12)
330262 432-HY (12) 333 6005 B (12) # 2 507-ST (12) VL-32 (24) VS-11/32 F (12)
330280 432-HY (12) 333 6005 B (12) # 2 507-ST (12) VL-32 (24) VS-11/32 F (12)
330-TKA 432-HY (12) 333 6005 B (12) # 2 507-ST (12) VL-32 (24) VS-11/32 F (12)
These items included in Cam & complete kit Optional accessories
FORD • — FALCON • MUSTANG • MAVERICK 6 Cyl. 250 cu. in Engines
RACING CAMSRecommended Valve Train Components
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
CAM & ADJUSTABLE VALVE SPRING STEEL COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42
321A-MK 392-HY (12) 303-B # 3 327-ST (12)
320255 392-HY (12) 303-B # 3 327-ST (12)
320266 392-HY (12) 303-B # 3 327-ST (12)
320288 392-HY (12) 303-B # 3 327-ST (12)
These items included in Cam & complete kit
B Requires cylinder heads be machined with Isky #208 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter
1005-W B
206-G (12)
1005-W B
206-G (12)
1005-W B
206-G (12)
1005-W B
206-G (12)
(12 pcs)
(12 pcs)
(12 pcs)
(12 pcs)
138
FORD - MERCURY • V-8 1932-53 FLATHEAD
CLARIFICATION OF FORD V-8 ENGINES
RACING CAMSSTREET
&STRIP
Valve Valve ADV. .050 Lift Lash Duration Duration Lobe 21-A 8-BA Grind No./Type APPLICATION TYPE INT. INT. INT. INT. Center 1932-48 1949-53 EX. EX. EX. EX.
217700 817700 77-B 3/4 .325 .014 260° 220° 111° SOLID .325 .014 260° 220°
211100 811100 MAX #1 3/4 .364 .014 249° 226° 111° SOLID .364 .014 249° 226°
218800 818800 88 FULL .320 .010 264° 224° 111° SOLID RACE .320 .012 264° 224°
214000 814000 400-JR TRACK .400 .018 258° 244° 111° SOLID .400 .018 258° 244°
210433 810433 433 All-Out .410 .020 280° 263° 111° SOLID Competition .410 .020 280° 263°
Good Low Speed and Mid-RangePower Cam. Good Idle.Std. Carburetion Ok.
Good Low Speed Power Camin conjunction with stock carb.and intake manifold. Good idle.
Good Mid-Range Power forhigh perf. street use.Fair idle. modified carb & intake recommended.
Competition use: oval track & drags.modified carb. and intake required.Lopey idle.
All-out competition only: Drags.modified carb. and intake required.Lopey idle.
Part No.Cam Only
289 Standard 15426378 Part No. 381 1.6:1 Rocker Ratio. Pre-1969 Engines have ball stud RockersPushrods guided in head (Isky Pushrod (#393-HG)
302 Standard 15426378 Part No. 381 1969 & up engines use rail-guide type Rocker Arms. Rocker guides over valvestem end. (Isky pushrod #393-HG)
302 Boss 15426378 Part No. 381
429-460 Part No. 311
Cobra-Jet429 &Super Cobra Jet Wedge
Part No. 311
429 Boss Isky cam Part No. 311No Kit Parts Available
1.76:1 Rocker Ratio. Fulcrum-Stud Rockers. Uses pushrod guide plates with hardened pushrods. Isky pushrod #963-HG when used with #204-96Rocker Arms.
1.75:1 Rocker Ratio. Rail guided, Mallable Iron Rockers, with shoulder-lock stud.(No method of Adjustment) Install 429 Cobra Jet Rocker Arms, studs & guideplates, when converting to solid lifter cam.
1.76:1 Stamped Steel Fulcrum-Stud Adjustable Rockers, withpushrod guide plates and hardened pushrods.
1.65:1 INT. & 1.75:1 EX. Rocker Ratio. Individual Stock-Adj.Shaft Rockers with pushrod guide plates and hardenedpushrods (oils thru rocker shafts).
351 Windsor 13726548 See cam section (351 Windsor)or use Part No. 381 & changefiring order to 15426378
1.6:1 Rocker Ratio. Rail-guide type rocker arms. Takes a longerpushrod than the standard 289-302 because block-deck is higher.(Isky pushrod #393-A-HG)
351 Cleveland400 Cleveland351-400M
351 Boss
1.76:1 Rocker Ratio. Rockers guided by cyl. head stud castles (posi-Lock Rockers) No method of adjustment (Stock engine comes with HYD. cam) Toconvert to solid lifter, heads must be machined to accept Boss 302-351 studs & guide plates.
SAME AS 302 BOSS
ENGINE FIRING ORDER ROCKER ARM & PUSHROD INFORMATIONISKY CAM, COMMENTSORDERING INSTRUCTIONS
13726548
Special cam, has largerfront Journal than the351 Windsor. Isky CamPart # 431
ALLSame FiringOrder
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
139
FORD - MERCURY • V-8 1932-53 FLATHEAD
RACING CAMSRecommended Valve Train Components
VALVE SPRING STEEL LIFTERS SPRINGS SHIMS RETAINERS 21-A (1932-48) 8-BA (1949-53) P. 10-25 P. 27-41 P. 51 P. 42
207700 807700 F85-02 185-G (single) # 404 —
201100 801100 F85-02 185-G (single) # 404 —
208800 808800 F85-02 185-G (single) # 404 —
204000 804000 F85-02 4005 (dual) # 404 87-F
200433 800433 F85-02 4005 (dual) # 404 87-F
These items included in Cam & complete kitCAM & COMPLETE KIT
PART NO.
140
FORD • CLEVELAND 351-400 & 351M-400M, BOSS-351
RACING CAMS
Cast Iron BilletHYDRAULICSOLID
1.75:1 Rocker Ratio
Valve Valve ADV. .050 Lift Lash Hot Duration Duration Lobe Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
431256 256-Supercam 1500-4800 .492 .000 256° 202° 112° HYDRAULIC .492 .000 256° 202°
431256/262 256/262 1800-5000 .492 .000 256° 202° 110° HYDRAULIC .488 .000 262° 208°
431262 262-Supercam 2000-5500 .488 .000 262° 208° 108° HYDRAULIC .488 .000 262° 208°
431264 264-MEGA 2000-5800 .525 .000 264° 214° 108° HYDRAULIC .525 .000 264° 214°
431270 270-HL 2000-6000 .510 .000 270° 216° 108° HYDRAULIC .510 .000 270° 216°
431271 270-MEGA 2000-6200 .542 .000 270° 221° 108° HYDRAULIC .542 .000 270° 221°
431281 280-MEGA 2500-6800 .565 .000 280° 232° 108° HYDRAULIC .565 .000 280° 232°
431292 292-MEGA 2800-7000 .590 .000 292° 244° 108° HYDRAULIC .590 .000 292° 244°
431-TA Turbocycle-A 1000-5000 .485 .000 264° 208° 114° HYDRAULIC .455 .000 252° 194°
431584 584 2600-6800 .584 .018 282° 247° 106° SOLID .588 .020 288° 254°
431360 FL-360 2500-6500 .530 .018 278° 240° 108° SOLID .530 .018 278° 240°
431380 FL-380 3000-7000 .560 .030 290° 250° 108° SOLID .560 .030 290° 250°
431570 FL-570 4000-8000 .644 .028 312° 266° 108° SOLID .644 .028 312° 266°
431670 FL-670 5000-8500 .682 .028 330° 284° 108° SOLID .682 .028 330° 284°
Best torque & economy in passenger cars & trucks.Max compr., 9.5:1, smooth idle, std. axle ratio, goodvacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4:10 axleratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks.Up to 625 CFM Carb.
Tremendous torque & good mid-range power.9-10.5:1 compr., good idle, stock converter.3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance use/bracket racing. Lopey idle.2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio.Up to 780 CFM Carb.
High performance use/bracket racing. Rough idle.2800 Stall. 10-11:1 compr. 4.11-4.56 axle ratio. Up to 780 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
Banked 1/4-3/8 mile oval tracks. Any carburetor.
Strong mid-range perf. Lopey idle. 2500 RPM stall.3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High perf. Use/bracket racing. Lopey idle.3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio.Up to 800 CFM Carb.
All-out competition/drags. Rough idle. 4500 stall. 4.88-5.38 axle ratio. 850 CFM Carb. 11:1 compr.
All out competition/drags. 5000 stall. 5.13-5.57 axle ratio. 850+CFM Carb. 12:1 compr.
Part No.Cam Only
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
141
FORD • CLEVELAND 351-400 & 351M-400M, BOSS-351
RACING CAMSRecommended Valve Train Components
CAM & A VALVE SPRING STEEL VALVE SPRING STEEL ADJ. LIFTER LIFTERS SPRINGS SHIMS RETAINERS LIFTERS SPRINGS SHIMS RETAINERS PUSHRODS KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 10-25 P. 27-41 P. 51 P. 42 P. 44-48
420256 430256 CL-431256 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420256/262 430256/262 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420262 430262 CL-431262 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420264 430264 CL-431264 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420270 430270 CL-431270 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420271 430271 CL-431271 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420281 430281 CL-431281 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420292 430292 CL-431292 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420-TKA 430-TKA — 432-HY 8005-A B # 2 507-STA 432-HY 6005 B # 2
420584 430584 — 382-H 8005-A B # 2 507-STA 382-H 6005 B # 2 —
420360 430360 — 382-H 8005-A B # 2 507-STA 382-H 6005 B # 2 —
420380 430380 — 382-H 8005-A B # 2 507-STA 382-H 6005 B # 2 —
420570 430570 — 382-H 8005-A B # 2 507-STA 382-H 6005 B # 2 —
420670 430670 — 382-H 8005-A B # 2 507-STA 382-H 6005 B # 2 —
351 Boss kit components 351/400 Cleveland/M KitComponents
A Cam & Lifter kits are supplied with 432-HY lifters B Requires cylinder heads be machined with Isky #1258 Hole Saw J 351 Cleveland only
L 400 Engines & 351M onlyM Single groove valve stem applications N For use on engines with rotating valves and 4-groove valve locks.
* NOTE: Cleveland 351 heads must be machined to accept boss 302. 351 guide plate, studs and rocker arms in order to obtain adjustment for solid lifter cams, or use isky adjustable pushrods. # 393-DA (Adjustable pushrods 351 Cleveland) #403-A (Adjustable pushrods 351-M & 400 engines)
CAM & COMPLETE KITPART NO.
351 351/400 BOSS CLEVE/M
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
507-ST M 393-DA J
607-STA N 403-A L
CL-431256/262
*
*
*
*
142
FORD • V-8 BOSS-351 Engine only
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
431640 RR-640 3200-6800 .640 .028 304° 264° 108° ROLLER .640 .028 304° 264°
431650 RR-650 3500-7200 .650 .028 318° 272° 108° ROLLER .650 .028 318° 272°
431686 RR-686 4500-8000 .686 .028 320° 282° 108° ROLLER .686 .028 320° 282°
431730 RR-730 3800-7500 .730 .028 314° 272° 108° ROLLER .730 .028 314° 272°
431727 RR-727 4500-8500 .727 .030 330° 286° 108° ROLLER .727 .030 330° 286°
431749 RR-747-C 4200-8400 .747 .028 318° 284° 106° ROLLER .730 .028 320° 288°
431750 RR-747-D 4400-8800 .747 .028 320° 288° 106° ROLLER .730 .028 322° 292°
STEELBILLETROLLER
1.75:1 Rocker Ratio
Good cam for 3500LB bracket racing “drags”. 3000 stall. 4.56-4.88 axle ratio. 11-12:1 compr. Up to 800 CFM Carb.
Good all around perf. for bracket racing. 4000-4500 stall. 4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM.
Super Gas, Super Comp: 5000 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM.
Comp. eliminator, super-comp drags. 5000+stall. 5.86-6.14 axle ratio. High compr. Tunnel ram manifold with 2 carburetors.
Comp. eliminator, super-comp drags. 5000+stall. 5.86-6.14 axle ratio. High compr. Tunnel ram manifold with 2 carburetors.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
143
FORD • V-8 BOSS-351 Engine only
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & ROLLER VALVE SPRING STEEL BRONZE VALVE VALVE COMPLETE LIFTERS SPRINGS SHIMS RETAINERS DIST. GEAR PUSHRODS LOCKS SEALS KIT P/N P. 15-25 P. 27-41 P. 51 P. 42 P. 56 P. 44-48 P. 53 P. 52
420640 3572RH 9315 #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420650 3572RH 9315 #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420686 3572RH 9315 #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420730 3572RH 9315U #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420727 3572RH 9315U #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420749 3572RH 9315U #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
420750 3572RH 9315U #2 527STA 430-DG 393-C-HG G VL-32 VS-11/32 F
F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads. U For High-Revving Motors, use our optional 9425 Spring, 275-ST Retainer and VL-700 Valve Lock Combo.
144
FORD BOSS • 302 V-8
RACING CAMS1.75:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
381360 FL-360 2500-6500 .530 .018 278° 240° 108° SOLID .530 .018 278° 240°
381380 FL-380 3000-7000 .560 .030 290° 250° 108° SOLID .560 .030 290° 250°
381370 FL-370 3000-7000 .528 .028 300° 250° 108° SOLID .528 .028 300° 250°
381470 FL-470 3500-7500 .602 .028 304° 266° 108° SOLID .602 .028 304° 266°
381570 FL-570 4000-8000 .644 .028 312° 266° 108° SOLID .644 .028 312° 266°
381670 FL-670 5000-8500 .682 .028 330° 284° 108° SOLID .682 .028 330° 284°
381644 RR-640 3200-6800 .640 .028 304° 264° 108° ROLLER .640 .028 304° 264°
381650 RR-650 3500-7200 .650 .028 318° 272° 108° ROLLER .650 .028 318° 272°
381686 RR-686 4500-8000 .686 .028 320° 282° 108° ROLLER .686 .028 320° 282°
381730 RR-730 3800-7500 .730 .028 314° 272° 108° ROLLER .730 .028 314° 272°
381727 RR-727 4500-8500 .727 .030 330° 286° 108° ROLLER .727 .030 330° 286°
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High perf. Use/bracket racing. Lopey idle. 3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio. Up to 800 CFM Carb.
High perf. Use/bracket racing. Lopey idle. 3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio. Up to 800 CFM Carb.
All out drags. 4000-4500 stall. 4.56-4.88 axle ratio. 850+CFM Carb. 11.5:1+compr.
All-out competition/drags. Rough idle. 4500 stall. 4.88-5.38 axle ratio. 850 CFM Carb. 11:1 compr.
All out competition/drags. 5000 stall. 5.13-5.57 axle ratio.850+CFM Carb. 12:1 compr.
Good cam for 3500LB bracket racing “drags”. 3000 stall. 4.56-4.88 axle ratio. 11-12:1 compr. Up to 800 CFM Carb.
Good all around perf. for bracket racing. 4000-4500 stall. 4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM.
Super Gas, Super Comp: 5000 stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
SOLID
ROLLER
145
FORD BOSS • 302 V-8
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL BRONZE VALVE VALVE COMPLETE LIFTERS SPRINGS SHIMS RETAINERS DIST. GEAR PUSHRODS LOCKS SEALS KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 56 P. 44-48 P. 53 P. 52
380360 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380380 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380370 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380470 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380570 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380670 382H 8005-A #2 507STA — 393-B-HG G VL-32 VS-11/32 F
380644 3972RH 9315 #2 527STA 380-DG 393-B-HG G VL-32 VS-11/32 F
380650 3972RH 9315 #2 527STA 380-DG 393-B-HG G VL-32 VS-11/32 F
380686 3972RH 9315 #2 527STA 380-DG 393-B-HG G VL-32 VS-11/32 F
380730 3972RH 9315 U #2 527STA 380-DG 393-B-HG G VL-32 VS-11/32 F
380727 3972RH 9315 U #2 527STA 380-DG 393-B-HG G VL-32 VS-11/32 F
F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads. U For High-Revving Motors, use our optional 9425 Spring, 275-ST Retainer and VL-700 Valve Lock Combo.
146
FORD • V-8 221-260-289-302 cu. in. engines THESE CAMS MAY BE USED IN 351 WINDSOR BYCHANGING TO 289 FIRING ORDER
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
381256 256-SUPERCAM 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
381256/262 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .445 .000 262° 208°
381262 262-SUPERCAM 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
381264 264-MEGA ` 2000-5800 .480 .000 264° 214° 108° HYDRAULIC .480 .000 264° 214°
381270 270-HL 2000-6000 .470 .000 270° 216° 108° HYDRAULIC .470 .000 270° 216°
381271 270-MEGA 2000-6200 .496 .000 270° 221° 108° HYDRAULIC .496 .000 270° 221°
381280 280 2500-6500 .467 .000 280° 224° 108° HYDRAULIC .467 .000 280° 224°
381281 280-MEGA 2500-6800 .517 .000 280° 232° 108° HYDRAULIC .517 .000 280° 232°
381292 292-MEGA 2800-7000 .538 .000 292° 244° 108° HYDRAULIC .538 .000 292° 244°
381304 304-MEGA 3200-7500 .560 .000 304° 256° 108° HYDRAULIC .560 .000 304° 256°
381-TA TURBOCYCLE-A 1000-5000 .445 .000 262° 208° 114° HYDRAULIC .415 .000 250° 194°
381-TB TURBOCYCLE-B 2000-6000 .470 .000 274° 216° 114° HYDRAULIC .435 .000 260° 200°
1.6:1 Rocker Ratio
Best torque & economy. Passenger cars & trucks. Max compr. 9.5:1. Smooth idle. Standard axle ratio. Good vacuum. Computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/mid-range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr. Good idle. Stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3:70-4:11 axle ratio. Up to 650 CFMCarb. 9.5:1 compr.
Excelent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr. 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance. Lopey idle. 2500 Stall. 3:70-4:11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
High performance. Use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3:90-4:11 axle ratio. Up to 780 CFM Carb.
High performance. Use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4:11-4:56 axle ratio. Up to 780 CFM Carb.
Ultimate high performance Use/bracket racing. Rough idle. 3000 Stall. 11:1 & up compr. 4:33-4:88 axle ratio. Up to 850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
High performance. Turbocharged appl’s. with higher boost. Good idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
RACING CAMS
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron Billet
HYDRAULIC
147
FORD • V-8 221-260-289-302 cu. in. engines THESE CAMS MAY BE USED IN 351 WINDSOR BYCHANGING TO 289 FIRING ORDER
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVECOMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
380256 CL-381256 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380256/262 CL-381256/262 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380262 CL-381262 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380264 CL-381264 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380270 CL-381270 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380271 CL-381271 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380280 CL-381280 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380281 CL-381281 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380292 CL-381292 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380304 CL-381304 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380-TKA N/A 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
380-TKB N/A 432-HY 393-HGD,G 6005B # 2 507-ST PL-3/8D 380-TS VL-32 VS-11/32F
A Cam & Lifter Lits are supplied with 432-HY Lifters B Requires cylinder heads be machined with Isky #1258 Hole Saw D 289/302 Cylinder Heads only. (For 351-W Cylinder Heads, use 393-A-HG Pushrods and PL-5/16 Poly Locks) F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads
148
FORD • V-8 221-260-289-302 cu. in. engines THESE CAMS MAY BE USED IN 351 WINDSOR BYCHANGING TO 289 FIRING ORDER
RACING CAMS1.6:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
381333 RPM-300 2000-6000 .476 .020 270° 228° 108° SOLID .476 .020 270° 228°
381358 FL-358 2500-6500 .512 .018 278° 244° 108° SOLID .512 .018 278° 244°
381368 FL-368 3000-7000 .476 .020 290° 250° 108° SOLID .476 .020 290° 250°
381378 FL-378 3000-7000 .512 .030 290° 250° 108° SOLID .512 .030 290° 250°
381505 505-T 3500-7000 .540 .028 290° 254° 108° SOLID .540 .028 290° 254°
381468 FL-468 3500-7500 .540 .028 304° 266° 108° SOLID .540 .028 304° 266°
381568 FL-568 4000-8000 .578 .028 312° 264° 108° SOLID .578 .028 312° 264°
381608 FL-608 4000-8000 .608 .028 320° 274° 108° SOLID .608 .028 320° 274°
381641 RR-641 3500-7500 .640 .028 300° 260° 108° ROLLER .640 .028 300° 260°
381672 RR-672 4000-8000 .672 .028 314° 272° 108° ROLLER .672 .028 314° 272°
381673 RR-670-A 4000-8000 .670 .028 310° 276° 104° ROLLER .670 .028 314° 280°
381674 RR-670-B 4000-8000 .670 .028 310° 276° 106° ROLLER .670 .028 314° 280°
381704 RR-704 4500-8500 .704 .028 324° 282° 108° ROLLER .704 .028 324° 282°
Good low to mid–range performance. Fair idle. 2500 Stall. 3:70–4:11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
High performance Use. Rough idle. Great mid–range power. 2500 Stall. 3:70–4:11 axle ratio. Up to 650 CFM Carb.
Strong mid –range performance. Lopey idle. 2500 RPM Stall. 3:70–4:11 axle ratio. 650–750 CFM Carb. 10.5:1 compr.
Strong mid –range performance. Lopey idle. 2500 RPM Stall. 3:70–4:11 axle ratio. 650–750 CFM Carb. 10.5:1 compr.
Bracket racing. Rough idle. 2800 Stall. 4:11-4:56 axleratio. 650-750 CFM Carb. 10:1 compr.
All-out competition/drags. Rough idle. 4500 Stall.4:88-5:38 axle ratio. 850 CFM Carb. 11:1 compr.
All-out competition/drags. Rough idle. 4500 Stall.4:88-5:38 axle ratio. 850 CFM Carb. 11:1 compr.
All out drags. Rough idle. 5000 Stall. 5:13-5:38 axleratio. 850+CFM Carb. 12:1 compr.
Good cam for 3500LB bracket racing “drags”. 3000 stall. 4.56-4.88 axle ratio. 11-12:1 compr. Up to 800 CFM Carb.
Good all around perf. for bracket racing. 4000-4500 stall. 4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Super stock automatic; 289-302 cu. in. 4500-5000 stall. 5.13-5.57 axle ratio. High compr.
Super stock, 4-speed; 289-302 cu. in. 5.13-5.57 axle ratio. High compr.
Good all-around perf. in super-gas & super comp. 5000+ stall. 5.57-5.86 axle ratio. High compr. 850+CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
SOLID
ROLLER
149
FORD • V-8 221-260-289-302 cu. in. engines THESE CAMS MAY BE USED IN 351 WINDSOR BYCHANGING TO 289 FIRING ORDER
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL POLY BRONZE TIMING VALVE VALVE COMPLETE LIFTERS SPRINGS SHIMS RETAINERS LOCKS DIST. GEAR SET PUSHRODS LOCKS SEALS KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56 P. 56-57 P. 44-48 P. 53 P. 52
380333 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380358 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380368 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380378 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380505 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380468 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380568 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380608 382-H 6005B #2 507-ST PL-3/8D — 380-TS 393-SL-HGD,G VL-32 VS-11/32F
380641 3972RH 9315Q #2 527STA PL-3/8D 380-DG — 393--HG D,G VL-32 VS-11/32F
380672 3972RH 9315Q #2 527STA PL-3/8D 380-DG — 393--HG D,G VL-32 VS-11/32F
380673 3972RH 9315Q #2 527STA PL-3/8D 380-DG — 393--HG D,G VL-32 VS-11/32F
380674 3972RH 9315Q #2 527STA PL-3/8D 380-DG — 393--HG D,G VL-32 VS-11/32F
380704 3972RH 9315Q #2 527STA PL-3/8D 380-DG — 393--HG D,G VL-32 VS-11/32F
B Requires cylinder heads be machined with Isky #1258 Hole Saw D 289/302 cylinder heads only. (For 351-W Cylinder Heads, use 683-A-HG Pushrods and PL-5/16 Poly Locks)
F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads. Q Requires cylinder heads be machined with 3608 Hole Saw
150
FORD • V-8 1969-UP • 351- WINDSOR
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
388256 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
388256/262 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .445 .000 262° 208°
388262 262-Supercam 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
388270 270-HL 2000-6000 .470 .000 270° 216° 108° HYDRAULIC .470 .000 270° 216°
388566 566-A 2600-6800 .566 .018 282° 248° 106° SOLID .560 .020 288° 254°
1.6:1 Rocker Ratio
Best torque & economy. Passenger cars & trucks. Maximumcomp. 9.5:1. Smooth idle. Standard axle ratio. Good vacuum. Computer compatible. Standard to 600 CFM carb.
Best overall cam for towing. Trucks, Vans, R.V., etc.Broad torque band. Good vacuum. 3.55-4.10 axle ratio.9.5:1 compr. Computer compatible. Smooth idle.
Low/mid-range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Good All-Around Performance. Fair idle. stock Converter.3:70-4:11 Axle Ratio. up tp 650 CFM Carb. 9.5:1 Compr.
1/4-3/8 mile oval tracks with little or no bank.2BBL. carburetor.
Note: Factory production 5.0 litre H.O. Camshaft specs are: 266 DEG. ADV. Duration, 210 DEG. @. 050" and .444" Valve Lift for Intake & Exhaust
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
NOTE: THE 302-HO HYDRAULIC ROLLER CAMS LISTED BELOW UTILIZE THE 351-W FIRINGORDER AND CAN BE INSTALLED IN 1985 AND LATER STANDARD 302 ENGINES BY REWIRING THE FIRING ORDER TO (1-3-7-2-6-5-4-8)
RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
371252/257 RR-252/257 HYD 1200-5000 .465 .000 252° 204° 112° .480 .000 257° 210°
371257/265 RR-257/265 HYD 1400-5600 .480 .000 257° 210° 112° .500 .000 265° 218°
371265/275 RR-265/275 HYD 2000-6000 .500 .000 265° 218° 112° .520 .000 275° 228°
371275/284 RR-275/284 HYD 2500-6400 .520 .000 275° 228° 112° .544 .000 284° 238°
371284/294 RR-284/294 HYD 3000-7000 .544 .000 284° 238° 110° .573 .000 294° 248°
HYDRAULICROLLER
1.6:1 Rocker Ratio
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Excellent performance cam with good vacuum, good idle.3.08-3.73 axle ratio, 9.5:1 compr. Up to 650 CFM Carb.Computer compatible. Stock converter.
Good mid-range power. Good vacuum & good idle. 3.23-3.70 axle ratio. 9.5-10.5:1 compr. Computer compatiblewith stage 1 chip. Stock converter. Up to 650 CFM Carb.
Good all around performance. Good idle & vacuum. 3.70-4.11 axle ratio. 9.5-10.5:1 compr. Computercompatible with stage 1 or 2 chip. Stock converter.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
Cast Iron BilletHYDRAULIC
SOLID
HYDRAULIC ROLLER CAMSHAFTS—STEEL BILLETFORD V8—302 CU. IN. 5.0 LITRE HO (1985-95) (FIRING ORDER: 1-3-7-2-6-5-4-8)
151
FORD • V-8 1969-UP • 351- WINDSOR
RACING CAMS
RACING CAMS
HYDRAULIC ROLLER CAMSHAFTS—STEEL BILLETFORD V8—302 CU. IN. 5.0 LITRE HO (1985-95) (FIRING ORDER: 1-3-7-2-6-5-4-8)
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING STEEL POLY TIMING VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
385256 432-HY 393-A-HGG 6005B #2 507-ST PL-5/16 380-TS VL-32 VS-11/32F
385256/262 432-HY 393-A-HGG 6005B #2 507-ST PL-5/16 380-TS VL-32 VS-11/32F
385262 432-HY 393-A-HGG 6005B #2 507-ST PL-5/16 380-TS VL-32 VS-11/32F
385270 432-HY 393-A-HGG 6005B #2 507-ST PL-5/16 380-TS VL-32 VS-11/32F
385566 382-H 683-A-HGG 6005B #2 507-ST PL-5/16 – VL-32 VS-11/32F
Recommended Valve Train Components
B Requires cylinder heads be machined with Isky #1258 Hole Sawr F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads.
NOTE: USE LATE MODEL (1985 & UP) FACTORY HYDRAULIC ROLLER LIFTERS WITH THESE CAM & ASSEMBLY KITS.
CAM & VALVE SPRING STEEL COMPLETE PUSHRODS SPRINGS SHIMS RETAINERS KIT P/N P. 44-48 P. 27-41 P. 51 P. 42
370252/257 203-RM-HGG 3105-D # 1 —
370257/265 203-RM-HGG 3105-D # 1 —
370265/275 203-RM-HGG 3105-D # 1 —
370275/284 203-RM-HGG 6005 B # 2 507-ST
370284/294 203-RM-HGG 6005 B # 2 507-ST
These items included in Cam & complete kit
SPECIAL NOTE: 1985 and later 302 cu. in. Hyd. RollerCams CAN be installed in earlier 302 &351 cu. in. Windsor engines by also installing our retrofit part no. 3877-HYRTHyd. Roller Lifters and Corresponding pushrods. See page 13 for more information on these components.
152
FORD • V-8 352-360-361-390-406-427-428 cu. in. engines (1963 & up)
RACING CAMS1.75:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
351256 256-SUPERCAM 1500-4800 .492 .000 256° 202° 112° HYDRAULIC .492 .000 256° 202°
351256/262 256/262 1800-5000 .492 .000 256° 202° 110° HYDRAULIC .488 .000 262° 208°
351262 262-SUPERCAM 2000-5500 .488 .000 262° 208° 108° HYDRAULIC .488 .000 262° 208°
351264 264-MEGA 2000-5800 .525 .000 264° 214° 108° HYDRAULIC .525 .000 264° 214°
351270 270-HL 2000-6000 .510 .000 270° 216° 108° HYDRAULIC .510 .000 270° 216°
351271 270-MEGA 2000-6000 .542 .000 270° 221° 108° HYDRAULIC .542 .000 270° 221°
351281 280-MEGA 2500-6800 .565 .000 280° 232° 108° HYDRAULIC .565 .000 280° 232°
351350 EE-350 2500-6000 .525 .018 264° 228° 108° SOLID .525 .018 264° 228°
351360 EE-360 2500-6200 .530 .018 278° 240° 108° SOLID .530 .018 278° 240°
351391 EE-391 3000-7000 .560 .030 290° 250° 108° SOLID .560 .030 290° 250°
351392 EE-392 3500-7500 .590 .028 300° 254° 108° SOLID .590 .028 300° 254°
351393 EE-393 4000-7000 .596 .026 320° 266° 108° SOLID .596 .026 320° 266°
351396 EE-396 3500-7000 .630 .028 312° 266° 108° SOLID .630 .028 312° 266°
351399 EE-399 4000-7500 .632 .028 324° 276° 108° SOLID .632 .028 324° 276°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr., good idle, stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
Good mid-range power. Fair idle, stock converter. 3.55-3.90 axle ratio. 600-650 CFM Carb. 10:1 compr.
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High perf. Use/bracket racing. Lopey idle. 3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio. Up to 800 CFM Carb.
Bracket racing. Rough idle. 3000 stall. 4.11-4.56 axle ratio. Up to 850 CFM Carb. 10.5:1 compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All out drags. 4000-4500 stall. 4.56-4.88 axle ratio. 850+CFM Carb. 11.5:1+compr.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron BilletHYDRAULIC
SOLID
153
FORD • V-8 352-360-361-390-406-427-428 cu. in. engines (1963 & up)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL TIMING VALVE VALVECOMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 56-57 P. 53 P. 52
350256 CL-351256 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350256/262 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350262 CL-351262 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350264 CL-351264 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350270 CL-351270 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350271 CL-351271 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350281 CL-351281 392-HY 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350350 — 382-H 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350360 — 382-H 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350391 — 382-H 383 8005-A # 2 3607-ST 350-TS VL-3/8 VS-3/8F
350392 — 382-H 383 8005-A # 2 3607-ST — VL-3/8 VS-3/8F
350393 — 382-H 383 8005-A # 2 3607-ST — VL-3/8 VS-3/8F
350396 — 382-H 383 8005-A # 2 3607-ST — VL-3/8 VS-3/8F
350399 — 382-H 383 8005-A # 2 3607-ST — VL-3/8 VS-3/8F
A Cam & Lifter kits are supplied with 392-HY Lifters F Requires cylinder heads be machined with VST-3/8 Cutter
CL-351256/262
154
FORD • V-8 1968 and up 370-429-460 cu. in. (WEDGE ENGINES ONLY)
RACING CAMS1.75:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
311256 256-SUPERCAM 1500-4800 .492 .000 256° 202° 112° HYDRAULIC .492 .000 256° 202°
311256/262 256/262 1800-5000 .492 .000 256° 202° 110° HYDRAULIC .488 .000 262° 208°
311262 262-SUPERCAM 2000-5500 .488 .000 262° 208° 108° HYDRAULIC .488 .000 262° 208°
311264 264-MEGA 2000-5800 .525 .000 264° 214° 108° HYDRAULIC .525 .000 264° 214°
311270 270-HL 2000-6000 .510 .000 270° 216° 108° HYDRAULIC .510 .000 270° 216°
311271 270-MEGA 2000-6000 .542 .000 270° 221° 108° HYDRAULIC .542 .000 270° 221°
311281 280-MEGA 2500-6800 .565 .000 280° 232° 108° HYDRAULIC .565 .000 280° 232°
311-TA Turbocycle-A 1000-5000 .485 .000 264° 208° 114° HYDRAULIC .455 .000 252° 194°
311-TB Turbocycle-B 2000-6000 .515 .000 274° 216° 114° HYDRAULIC .475 .000 260° 200°
311360 EE-360 2500-6200 .530 .018 278° 240° 108° SOLID .530 .018 278° 240°
311391 EE-391 3000-7000 .560 .030 290° 250° 108° SOLID .560 .030 290° 250°
311392 EE-392 3500-7500 .590 .028 300° 254° 108° SOLID .590 .028 300° 254°
311289 Z-89 3500-7500 .630 .028 304° 264° 108° SOLID .630 .028 304° 264°
311295 Z-95 4500-7500 .665 .030 320° 274° 108° SOLID .665 .030 320° 274°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr., good idle, stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
High performance turbocharged appl’s. with higher boost.Good idle, stock converter, std. axle ratio. Up to 650 CFM Carb.
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High perf. Use/bracket racing. Lopey idle. 3000 stall. 10.5:1 compr. 3.90-4.11 axle ratio. Up to 800 CFM Carb.
Bracket Racing. Rough idle. 3000 stall. 4.11-4.56 axle ratio. Up to 850 CFM Carb. 10.5:1 compr.
Good pulling power for drags in heavy car. Rough idle. 3500 stall. 4.33-4.56 axle ratio. 11:1 compr. Up to 850 CFM Carb.
All out drags. 5000 stall. 4.88-5.13 axle ratio. 850+CFM Carb. 12:1 compr.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Cast Iron BilletHYDRAULIC
SOLID
155
FORD • V-8 1968 and up 370-429-460 cu. in. (WEDGE ENGINES ONLY)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVECOMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
310256 CL-311256 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310256/262 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310262 CL-311262 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310264 CL-311264 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310270 CL-311270 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310271 CL-311271 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310281 CL-311281 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310-TKA — 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310-TKB — 432-HY 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310360 — 382-H 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310391 — 382-H 383-C-HGG 8005-AB # 2 PL-7/16 310-TS VL-32 VS-11/32F
310392 — 382-H 383-C-HGG 8005-AB # 2 — — VL-32 VS-11/32F
310289 — 382-H 383-C-HGG 8005-AB # 2 — — VL-32 VS-11/32F
310295 — 382-H 383-C-HGG 8005-AB # 2 — — VL-32 VS-11/32F
A Cam & Lifter kits are supplied with 432-HY Lifters B Requires cylinder heads be machined with Isky #1258 Hole Saw D For use on cobra-jet cylinder heads to prevent interference with rail guide rocker arms F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads
CL-311256/262
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
507-STA507-STD
156
FORD • V-8 1968 and up 370-429-460 cu. in. (WEDGE ENGINES ONLY)
RACING CAMS
STEELBILLETROLLER
1.75:1 Rocker Ratio
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
311640 RR-640 3200-6800 .640 .028 304° 264° 108° ROLLER .640 .028 304° 264°
311650 RR-650 3500-7200 .650 .028 318° 272° 108° ROLLER .650 .028 318° 272°
311730 RR-730 3800-7500 .730 .028 314° 274° 108° ROLLER .730 .028 314° 274°
311770 RR-770 4500-8500 .770 .028 324° 284° 108° ROLLER .770 .028 324° 284°
311772 RR-772 4500-8500 .772 .028 332° 288° 108° ROLLER .772 .028 332° 288°
311774 RR-774 4800-8800 .770 .028 324° 284° 110° ROLLER .772 .028 332° 288°
311800 RR-800-A 5200-9200 .800 .028 332° 288° 114° ROLLER .801 .030 344° 304°
311801 RR-800-B 5500-9500 .800 .028 336° 294° 114° ROLLER .801 .030 344° 304°
High perf. useage, bracket race drags. 3000 stall. 4.10-4.56 axle ratio. 11-12:1 compr. 780+CFM Carb.
Bracket Racing. 4000 stall. 4.56-4.88 axle ratio. High compr. 850+CFM Carb.
Super Gas: 4500 stall. 4.56-4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super gas, super comp. 4500+stall. 4.88 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super gas, super comp. 4500+stall. 4.88-5.13 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Super gas, super comp. 4500+stall. 4.88-5.13 axle ratio. High compr. Tunnel Ram Intake with 2 carburetors.
Pro-Stock; 500 cu.in./blown alcohol applications; Lenco transmission. High compr. Tunnel Ram Intake with 2 carburetors. 5.13-5.38 axle ratio.
Pro-Stock; Mountain Motor. Lenco transmission.High compr. Tunnel Ram Intake with 2 carburetors. 5.13-5.38 axle ratio.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
SPECIAL NOTE: We now have a retrofit hydraulic roller lifter (part no. 3177-HYRT)and corresponding P/N 203-HG+300 pushrods available for the429/460 Ford V-8. At the time of this catalog printing, we do NOThave any hydraulic roller cam cores, but do hope to have themavailable in the very near future. See page 13 for more information.
157
FORD • V-8 1968 and up 370-429-460 cu. in. (WEDGE ENGINES ONLY)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & ROLLER BRONZE VALVE SPRING VALVE VALVE VALVE COMPLETE LIFTERS DIST. GEAR SPRINGS SHIMS RETAINERS LOCKS PUSHRODS LOCKS SEALS KIT P/N P. 15-25 P. 56 P. 27-41 P. 51 P. 42-43 P. 53 P. 44-48 P. 53 P. 52
310640 3172RH 310-DG 9315B #2 527STAM — 383-C-HGG VL-32 VS-11/32F
310650 3172RH 310-DG 9315B #2 527STAM — 383-C-HGG VL-32 VS-11/32F
310730 3172RH 310-DG 9315B #2 527STAM — 383-C-HGG VL-32 VS-11/32F
310770 3172RH 310-DG 9705R #9/.030 975-TIO VL-700 383-C-HGG — VS-11/32F
310772 3172RH 310-DG 9705R #9/.030 975-TIO VL-700 383-C-HGG — VS-11/32F
310774 3172RH 310-DG 9705R #9/.030 975-TIO VL-700 383-C-HGG — VS-11/32F
310800 3172RH 310-DG 9705R #9/.030 975-TIO VL-700 383-C-HGG — VS-11/32F
310801 3172RH 310-DG 9705R #9/.030 975-TIO VL-700 383-C-HGG — VS-11/32F
B Requires cylinder heads be machined with Isky #3608 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter G Compatible with guide plate cylinder heads.
M Steel Retainers O Titanum Retainers R Requires cylinder heads be machined with 3708 Hole Saw
CAMSHAFT AND LIFTERSFOR 1964 AND UP OLDSMOBILE ENGINES
This chart has been made available by the Oldsmobile factory to clarify camshaft and lifter usage on 1964 and laterOldsmobile engines. NOTE: Due to the different tappet sizes and lobe spacings, it is imperative that full information regarding year, make, model,and original cubic inch displacement be given when ordering.
425-455 YEAR: 330- 400 Except 425-455ENGINES 350 Toronado Toronado
1964 Lifter dia. .842" — — — Cam Part No. .681 — — —1965 Lifter dia. .842" .842" .842" — Cam Part No. .681 .681 .681 —
1966 Lifter dia. .842" .921" .842" .921" Cam Part No. .681 .691 .681 .6911967 Lifter dia. .842" .921" .842" .921" Cam Part No. .691 .691 .691 .691
1968 Lifter dia. .842" .842" .842" .842"& Up Cam Part No. .691 .691 .691 .691
Note: Early Blocks with 45 Deg. Lifter Bank Angle use 681 Ordering Prefix. Late Blocks with 39 Deg. Lifter Bank Angle use 691 Ordering Prefix.
158
INTERNATIONAL • V-8 304-345-392 cu. in. engines
1.6:1 Rocker Ratio RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
190156 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
190125/26 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .465 .000 262° 208°
190162 262-Supercam 2000-5500 .465 .000 262° 208° 108° HYDRAULIC .465 .000 262° 208°
190170 270-HL 2000-6000 .490 .000 270° 216° 108° HYDRAULIC .490 .000 270° 216°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr.3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Cast Iron Billet
HYDRAULIC
OLDSMOBILE F-85 • V-8 1961-63 Aluminum 215 cu. in. engines (Pontiac 1961-62)
1.6:1 Rocker Ratio RACING CAMS
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
621256 256-Supercam 1500-4800 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
621262 262-Supercam 2000-5500 .445 .000 262° 208° 110° HYDRAULIC .445 .000 262° 208°
621270 270-HL 2000-6000 .470 .000 270° 216° 109° HYDRAULIC .470 .000 270° 216°
621282 282 2500-6500 .467 .000 282° 224° 109° HYDRAULIC .467 .000 282° 224°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter.3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
Cast Iron Billet
HYDRAULIC
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
159
INTERNATIONAL • V-8 304-345-392 cu. in. engines
RACING CAMSSorry. Hydraulic lifters are no longer available forthis motor.
OLDSMOBILE F-85 • V-8 1961-63 Aluminum 215 cu. in. engines (Pontiac 1961-62)
RACING CAMSRecommended Valve Train Components
These items included in Cam & complete kit Optional accessories
CAM & VALVE SPRING ALUMINUM VALVE VALVE COMPLETE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SEALS KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 53 P. 52
620256 202-HY 643 625/626B # 3 707-AL VL-32 VS-11/32F
620262 202-HY 643 625/626B # 3 707-AL VL-32 VS-11/32F
620270 202-HY 643 625/626B # 3 707-AL VL-32 VS-11/32F
620282 202-HY 643 625/626B # 3 707-AL VL-32 VS-11/32F
B Requires cylinder heads be machined with Isky # 208 Hole Saw F Requires cylinder heads be machined with VST-11/32 Cutter
160
OLDSMOBILE • V-8 1967 and up 330-350-400-403-425-455 cu. in. engines
1.6:1 Rocker Ratio RACING CAMSCast Iron Billet
HYDRAULIC
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
691256 256-Supercam 1500-4500 .450 .000 256° 202° 112° HYDRAULIC .450 .000 256° 202°
691256/262 256/262 1800-5000 .450 .000 256° 202° 110° HYDRAULIC .445 .000 262° 208°
691262 262-Supercam 2000-5500 .445 .000 262° 208° 108° HYDRAULIC .445 .000 262° 208°
691264 264-MEGA 2000-5800 .480 .000 264° 214° 108° HYDRAULIC .480 .000 264° 214°
691270 270-HL 2000-6000 .470 .000 270° 216° 108° HYDRAULIC .470 .000 270° 216°
691271 270-MEGA 2000-6000 .496 .000 270° 221° 108° HYDRAULIC .496 .000 270° 221°
691281 280-MEGA 2500-6800 .517 .000 280° 232° 108° HYDRAULIC .517 .000 280° 232°
691282 282 2500-6000 .467 .000 282° 224° 108° HYDRAULIC .467 .000 282° 224°
691291 292-MEGA 2800-7000 .538 .000 292° 244° 108° HYDRAULIC .538 .000 292° 244°
691292 292 3000-6800 .467 .000 292° 234° 108° HYDRAULIC .467 .000 292° 234°
691304 304-MEGA 3200-7500 .560 .000 304° 256° 108° HYDRAULIC .560 .000 304° 256°
691-TA Turbocycle-A 1000-5000 .465 .000 264° 208° 114° HYDRAULIC .425 .000 250° 194°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr., good idle, stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
High performance use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4.11-4.56 axle ratio. Up to 780 CFM Carb.
Bracket racing. Rough idle. 2800 stall. 4.11-4.56 axle ratio. 650-750 CFM Carb. 10:1 compr.
Ultimate high-performance use/bracket racing. Rough idle. 3000 Stall.11:1 & up compr. 4.33-4.88 axle ratio. Up to 850 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
see page 157 for ordering information on 1964-66 engines
161
RACING CAMSRecommended Valve Train Components
OLDSMOBILE • V-8 1967 and up 330*-350*-400-403-425-455 cu. in. engines
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE C SPRING STEEL C POLY TIMING VALVE VALVECOMPLETE LIFTER LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS SET LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 53 P. 52
690256 CL-691256 692-HYV 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690256/262 692-HYV 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690262 CL-691262 692-HYV 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690264 CL-691264 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690270 CL-691270 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690271 CL-691271 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690281 CL-691281 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690282 CL-691282 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690291 CL-691291 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690292 CL-691292 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690304 CL-691304 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
690-TKA — 692-HYV 5005 # 2 927-ST OFB-16 690-TS VL-32 VS-11/32F
A Cam & Lifter Kits are supplied with 692-HY LiftersD1 350 C.I. Engines onlyD2 330 C.I. Engines onlyD3 1965 & 1968-76, 400-425-455 C.I. Engines onlyD4 1966 & 1967, 400 C.I. Only F Requires cylinder heads be machined with VST-11/32 Cutter V .842" DIA. Lifters (see chart on page 151)
C SPECIAL NOTE: Valve Springs & Retainers for late Model and Marine Heads Approx. 1971 and later Oldsmobile heads have counter-bored valve spring pockets for valve rotaters. These heads require a different valve spring and retainer combination. Use the following: 6005 16 PAIR Dual Valve Springs 507-ST 16 Chrome Moly steel retainers
* General Motors has distributed engines between divisions in recent years. 1975-80 Oldsmobile cars with 350 cu. in. V8 engines may be built by either the Oldsmobile, Chevy or Buick division. 1975 400 cu. in. engines were built by the Pontiac division. Be sure of which G.M. division built your engine before ordering.
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
202-HY V
202-HYV
202-HYV
202-HYV
202-HYV
202-HYV
202-HYV
202-HYV
CL-691256/262
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
393-A D 1683-A D 2683-B D 3683-C D 4
162
PONTIAC • V-8 1955 and up 265-287-301-350-389-421-428-455 cu. in. engines
1.5:1 Rocker Ratio RACING CAMSCast Iron Billet
HYDRAULIC
(EXCEPT RAM AIR V ENGINES)
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
901256 256-Supercam 1500-4800 .425 .000 256° 202° 112° HYDRAULIC .425 .000 256° 202°
901256/262 256/262 1800-5000 .425 .000 256° 202° 110° HYDRAULIC .435 .000 262° 208°
901262 262-Supercam 2000-5500 .435 .000 262° 208° 108° HYDRAULIC .435 .000 262° 208°
901264 264-MEGA 2000-5800 .450 .000 264° 214° 108° HYDRAULIC .450 .000 264° 214°
901270 270-HL 2000-5500 .445 .000 270° 216° 108° HYDRAULIC .445 .000 270° 216°
901271 270-MEGA 2000-6200 .465 .000 270° 221° 108° HYDRAULIC .465 .000 270° 221°
901280 280-HL 2500-6000 .465 .000 280° 224° 108° HYDRAULIC .465 .000 280° 224°
901281 280-MEGA 2500-6800 .485 .000 280° 232° 108° HYDRAULIC .485 .000 280° 232°
901292 292-MEGA 2800-7000 .505 .000 292° 244° 108° HYDRAULIC .505 .000 292° 244°
901304 304-MEGA 3200-7500 .525 .000 304° 256° 108° HYDRAULIC .525 .000 304° 256°
901-TKA Turbocycle-A 1000-5000 .435 .000 264° 208° 114° HYDRAULIC .400 .000 252° 194°
901-TKB Turbocycle-B 2000-6000 .440 .000 274° 216° 114° HYDRAULIC .410 .000 260° 200°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, good vacuum, computer compatible. Std. to 600 CFM Carb.
Best overall cam for towing. Trucks, Vans, R.V., etc. Broad torque band. Good vacuum. 3.55-4:10 axle ratio. 9.5:1 compr. Computer compatible. Smooth idle.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Tremendous torque & good mid-range power. 9-10.5:1 compr., good idle, stock converter. 3.23-3.70 axle ratio. Up to 625 CFM Carb.
Good all-around performance. Fair idle. Stock converter.3.70-4.11 axle ratio. Up to 650 CFM Carb. 9.5:1 compr.
Excellent mid-range performance. Fair idle. Stock converter. 9-10.5:1 compr., 3.70-4.11 axle ratio. Up to 650 CFM Carb.
High perf. Use. Lopey idle. 2500 stall. 3.70-4.11 axle ratio. Up to 750 CFM Carb. 9.5:1 compr.
High performance use/bracket racing. Lopey idle. 2500 Stall. 9.5-10.5:1 compr. 3.90-4.11 axle ratio. Up to 780 CFM Carb.
High performance use/bracket racing. Rough idle. 2800 Stall. 10-11:1 compr. 4.11-4.56 axle ratio. Up to 780 CFM Carb.
Ultimate high-performance use/bracket racing. Rough idle. 3000 Stall.11:1 & up compr. 4.33-4.88 axle ratio. Up to 850 CFM Carb.
High performance turbocharged appl’s. with higher boost. Good idle, stock converter, std. axle ratio. Up to 650 CFM Carb.
Maximum economy/torque. Turbocharged. Up to 7 PSI Boost. Smooth idle. Stock converter. Std. axle ratio. Up to 650 CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
163
RACING CAMSRecommended Valve Train Components
PONTIAC • V-8 1955 and up 265-287-301-350-389-421-428-455 cu. in. engines(EXCEPT RAM AIR V ENGINES)
These items included in Cam & complete kit Optional accessories
CAM & CAM & A VALVE SPRING STEEL POLY TIMING VALVE VALVECOMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS SET PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56-57 P. 44-48 P. 53 P. 52
900256 CL-901256 692-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900256/262 692-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900262 CL-901262 692-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900264 CL-901264 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900270 CL-901270 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900271 CL-901271 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900280 CL-901280 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900281 CL-901281 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900292 CL-901292 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900304 CL-901304 202-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900-TKA N/A 692-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
900-TKB N/A 692-HY 5005 # 2 927-ST 900-TS 923-HGG VL-32 VS-11/32F
A Cam & Lifter Kits are supplied with 692-HY LiftersD1 1956-60 Engines onlyD2 1955 and 1961and up Engines only F Requires cylinder heads be machined with Isky VST-11/32 Cutter G Compatible with guide plate cylinder heads, 1967 & later engines
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
CL-901256/262
164
PONTIAC • V-8 1955 and up 265-287-301-350-389-421-428-455 cu. in. engines
1.5:1 Rocker Ratio RACING CAMS
(EXCEPT RAM AIR V ENGINES)
Valve Valve ADV. .050 Part No. Lift Lash Hot Duration Duration Lobe Cam Only Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
901303 RPM-300 2500-6000 .448 .020 270° 228° 108° SOLID .448 .020 270° 228°
901400 CC-400 2500-6200 .480 .018 278° 240° 108° SOLID .480 .018 278° 240°
901500 CC-500 3000-7000 .525 .016 288° 254° 108° SOLID .525 .018 288° 254°
901070 Z-70 3500-7500 .548 .028 304° 264° 108° SOLID .548 .028 304° 264°
901075 Z-75 4000-8000 .570 .028 320° 274° 108° SOLID .570 .028 320° 274°
901602 RR-602 3500-7500 .602 .028 300° 260° 108° ROLLER .602 .028 300° 260°
901630 RR-630 4000-8000 .630 .028 314° 272° 108° ROLLER .630 .028 314° 272°
901675 RR-675 4000-8000 .675 .024 308° 264° 108° ROLLER .630 .028 314° 272°
901660 RR-660 4500-8500 .660 .028 324° 282° 108° ROLLER .660 .028 324° 282°
901665 RR-665 4800-8800 .660 .028 324° 282° 108° ROLLER .662 .028 332° 286°
SOLID
ROLLER
Mid range perf: good idle. Stock converter. 3.70-4.11 axle ratio. Up to 650 CFM Carb. 9:1 compr.
Strong mid-range perf. Lopey idle. 2500 RPM stall. 3.70-4.11 axle ratio. 650-750 CFM Carb. 10.5:1 compr.
High perf. Street/strip. Lopey idle. 2800 stall. 4.11-4.88 axle ratio. Up to 750 CFM Carb. 10.5:1 compr.
Bracket racing. Lopey idle. 4000 stall. 4.88-5.38 axle ratio. Up to 850 CFM Carb. 11:1 compr.
All out competition/drags. 5000 stall. 5.13-5.57 axle ratio. 850+CFM Carb. 12:1 compr.
Good cam for 3500LB bracket racing “drags”. 3000 stall. 4.56-4.88 axle ratio. 11-12:1 compr. Up to 800 CFM Carb.
Good all around perf. for bracket racing. 4000-4500 stall. 4.88-5.13 axle ratio. 11-12:1 compr. 850+Carb.
Good mid-range perf. for heavy bracket racing “drags”. 3500-4000 stall. 4.56-5.13 axle ratio. 11-12:1 compr. Up to 850 CFM Carb.
Good all-around perf. in super-gas & super comp. 5000 stall. 5.38-5.86 axle ratio. High compr. 850+CFM Carb.
Good all-around perf. in super-gas & super comp. 5000+ stall. 5.57-5.86 axle ratio. High compr. 850+CFM Carb.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
165
RACING CAMSRecommended Valve Train Components
PONTIAC • V-8 1955 and up 265-287-301-350-389-421-428-455 cu. in. engines(EXCEPT RAM AIR V ENGINES)
These items included in Cam & complete kit Optional accessories
CAM & CAM & VALVE SPRING STEEL POLY BRONZE VALVE VALVECOMPLETE LIFTER LIFTERS SPRINGS SHIMS RETAINERS LOCKS DIST. GEAR PUSHRODS LOCKS SEALS KIT P/N KIT P/N P. 10-25 P. 27-41 P. 51 P. 42 P. 49 P. 56 P. 44-48 P. 53 P. 52
900303 — 202-H 5005 # 2 927-ST — — VL-32 VS-11/32F
900400 — 202-H 5005 # 2 927-ST — — VL-32 VS-11/32F
900500 — 202-H 5005 # 2 927-ST — — VL-32 VS-11/32F
900070 — 202-H 5005 # 2 927-ST — — VL-32 VS-11/32F
900075 — 202-H 5005 # 2 927-ST — — VL-32 VS-11/32F
900602 — 9672RH 9265C # 2 507-STAC PL-3/8 D2 900-DG 923-HGG VL-32 VS-11/32F
900630 — 9672RH 9265C # 2 507-STAC PL-3/8 D2 900-DG 923-HGG VL-32 VS-11/32F
900675 — 9672RH 9265C # 2 507-STAC PL-3/8 D2 900-DG 923-HGG VL-32 VS-11/32F
900660 — 9672RH 9265C # 2 507-STAC PL-3/8 D2 900-DG 923-HGG VL-32 VS-11/32F
900665 — 9672RH 9265C # 2 507-STAC PL-3/8 D2 900-DG 923-HGG VL-32 VS-11/32F
C For use on later model ram air IV or late production aftermarket alum. cyl. heads (1.875") installed height required.)D1 1956-60 Engines onlyD2 1961and up Engines only F Requires cylinder heads be machined with Isky VST-11/32 Cutter G Compatible with guide plate cylinder heads, 1967 & later engines
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
PL-5/16 D1
PL-3/8 D2
166
PONTIAC • 4 cyl. Super Duty 151 cu. in. “IRON DUKE,” 1979 and up
RACING CAMS
HYDRAULIC
SOLID
ROLLER
(HYDRAULIC & SOLID)
1.7:1 Rocker Ratio(ROLLER)
1.55:1 Rocker Ratio Valve Valve ADV. .050 Lift Lash Hot Duration Duration Lobe Grind No./Type APPLICATION RPM-Range INT. INT. INT. INT. Center EX. EX. EX. EX.
951256 — 256-Supercam 1500-4800 .480 .000 256° 202° 112° HYDRAULIC .480 .000 256° 202°
951262 — 262-Supercam 2000-5500 .493 .000 262° 208° 108° HYDRAULIC .493 .000 262° 208°
951271 — 270-MEGA 2000-6200 .527 .000 270° 221° 108° HYDRAULIC .527 .000 270° 221°
951281 — 280-MEGA 2500-6800 .549 .000 280° 232° 106° HYDRAULIC .549 .000 280° 232°
951284 — 284-MEGA 2600-6900 .578 .000 284° 236° 106° HYDRAULIC .578 .000 284° 236°
951292 — 292-MEGA 2800-7000 .572 .000 292° 244° 106° HYDRAULIC .572 .000 292° 244°
951560 — 560 2600-6800 .560 .020 276° 242° 106° SOLID .574 .020 282° 247°
951574 — 574 3000-7000 .574 .020 282° 247° 106° SOLID .568 .020 286° 252°
951568 — 568 3200-7200 .568 .020 286° 252° 106° SOLID .588 .020 294° 260°
951588 — 588 3400-7400 .588 .020 294° 260° 106° SOLID .588 .020 298° 264°
951663 N/A RR-660/60-68 4200-7600 .660 .028 294° 260° 106° ROLLER .660 .028 302° 268°
951647 N/A RR-660/68-76 4600-8000 .660 .028 302° 268° 106° ROLLER .660 .028 310° 276°
951682 N/A RR-682 4800-8400 .682 .028 324° 282° 104° ROLLER .682 .028 324° 282°
951760 N/A RR-760 5500-9200 .760 .028 326° 286° 106° ROLLER .708 .028 336° 292°
Best torque & economy in passenger cars & trucks. Max compr., 9.5:1, smooth idle, std. axle ratio, goodvacuum, computer compatible. Std. to 600 CFM Carb.
Low/Mid-Range performance cam. 9.5:1 compr. 3.08-3.70 axle ratio. Passenger cars & trucks. Up to 625 CFM Carb.
Hobby stock & street stock classes; 1/4-3/8 mile tracks with slight bank. 2BBL carburetor.
Hobby stock & street stock classes; banked 1/4-3/8 mile tracks. Any carburetor.
Street stock & sportsman classes; banked 3/8-1/2 mile tracks. Any carburetor.
Sportsman classes; 3/8-1/2 mile banked tracks. Any carburetor.
1/4-3/8 mile tracks with little or no bank. 2-BBL Carb.
Banked 1/4-3/8 mile tracks. Any carburetor.
Banked 3/8-1/2 mile tracks. Very broad power range. Any carburetor.
High bank 1/2 mile track; 4-BBL Carb.
Short Track Special: Banked 1/4-3/8 Mile (Goody’s Dash Series). Broad Power Band.
Long Track Special: Superspeedway(Daytona) W/Restrictor plate. Goody’s Dash Seies.
Long Track (Superspeedway) W/out Restrictor. Broad power band.
All-out competition: 1/4 mile drags.High compr. Multiple carburetion.
Part No.Cam Only
3-BRG. 5-BRG. CORE CORE
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
167
PONTIAC • 4 cyl. Super Duty 151 cu. in. “IRON DUKE,” 1979 and up
RACING CAMSRecommended Valve Train Components
VALVE SPRING VALVE ALUM-BRONZE LIFTERS PUSHRODS SPRINGS SHIMS RETAINERS LOCKS REV-KIT DIST. GEAR P. 10-25 P. 44-48 P. 27-41 P. 51 P. 42-43 P. 53 P. 56
950256 — 222-HY — — — — — — —
950262 — 222-HY — — — — — — —
950271 — 202-HY 923-HGG 805-DO # 2 507-STAM VL-32 — —
950281 — 202-HY 923-HGG 805-DO # 2 507-STAM VL-32 — —
950284 — 202-HY 923-HGG 805-DO # 2 507-STAM VL-32 — —
950292 — 202-HY 923-HGG 805-DO # 2 507-STAM VL-32 — —
950560 — 202-H 923-HGG 8005-A # 2 507-STAM VL-32 — —
950574 — 202-H 923-HGG 8005-A # 2 507-STAM VL-32 — —
950568 — 202-H 923-HGG 8005-A # 2 507-STAM VL-32 — —
950588 — 202-H 923-HGG 8005-A # 2 507-STAM VL-32 — —
950663 N/A 1271XL — 9205 # 5 91-TIO VL-700 1243-L (8) 250-DG
950647 N/A 1271XL — 9205 # 5 91-TIO VL-700 1243-L (8) 250-DG
950682 N/A 1271XL — 9205 # 5 91-TIO VL-700 1243-L (8) 250-DG
950760 N/A 1271XL — 9425 # 5 91-TIO VL-700 1243-L (8) 250-DG
These items included in Cam & complete kit
G Compatible with guide plate cylinder headsM Steel Retainers O Titanium Retainers
Cam & Complete KitPart No.
3-BRG. CORE 5-BRG. CORE
(8pcs)
(8pcs)
(8pcs) (8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (16pcs)
(8pcs) (8pcs) (16pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
(8pcs)
168
MARINE CAMS AND COMPONENTS
Big Block Chevy V-8 1.75:1 Rocker Ratio
Part No. Valve Valve Advertised .050 Lobe Cam Only Grind No./Type APPLICATION RPM-Range Lift Lash Hot Duration Duration Center
396278 278-MEGA 2000-5400 .525 .000 278° 234° 110° HYDRAULIC .525 .000 278° 234°
396282 280-MEGA 2000-5500 .565 .000 280° 232° 110° HYDRAULIC .565 .000 280° 232°
396271/281-14 270/280 MEGA 1800-5000 .543 .000 270° 221° 114° HYDRAULIC .565 .000 280° 232°
396281/292-14 280/292 MEGA 2000-5500 .565 .000 280° 232° 114° HYDRAULIC .590 .000 292° 244°
396257 Z-57 2500-6000 .590 .028 300° 254° 110° SOLID .590 .028 310° 264°
396290 Z-90 3000-6400 .595 .024 314° 264° 110° SOLID .635 .022 334° 274°
396297 Z-97 3600-7000 .665 .030 320° 274° 110° SOLID .654 .030 330° 286°
396645 RR-645 3600-6800 .640 .028 304° 264° 112° ROLLER .650 .028 318° 272°
396652 RR-652 4500-7400 .650 .028 318° 274° 110° ROLLER .654 .030 330° 286°
396732 RR-730-B 4800-7500 .730 .028 322° 282° 110° ROLLER .727 .030 330° 288°
396775 RR-775 5000-7700 .772 .028 332° 288° 110° ROLLER .763 .028 336° 294°
396811 RR-810B 5000-8500 .788 .028 318° 288° 112° ROLLER .788 .028 334° 300°
Jet boat, A-B impeller. All arounduse. Skiing, pleasure use.
Jet boat, A-B impeller.Skiing and high performance use.
Stage 1 pleasure use.Mercruiser I-O drive.
Stage 2, perf. use.Mercruiser I-O drive.
Good all-around perf. for V-drive with moderate compr.
High perf. use. Bracket racing, V-drive, high compr.
Excellent circle racing application,V-drive, flat bottom.
Best high perf. jet boat cam.B-impeller
Bracket racing:jet w/B-impeller,flat bottom, hydro
Bracket racing. Normallyaspirated or superchargedgas flat bottom, hydro.
Bracket racing. Normallyaspirated or superchargedgas flat bottom, hydro.
NOTE: Additional Cam Profiles are available in each category to suit any special application requirements.Contact the Isky Factory Technical Department for assistance.
All-out-racing: gas oralcohol normally aspiratedor supercharged
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
169
MARINE CAMS AND COMPONENTS
Big Block Chevy V-8 Recommended Valve Train Components
◊ Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
RetainersLifters Timing Set Pushrods Rocker Arms Valve Springs Steel Titanium Valve Locks Dist. Gear
Page 10-25 Page 56-57 Page 44-48 Page 49 ◊ Page 27-41 Page 42 Page 43 Page 53 Page 56
347-ST - VL-3/8202-HY 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-HY 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-HY 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-HY 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-H 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-H 390-TS 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
347-ST - VL-3/8202-H 203-96 204-96 8005-A 200DGS
175-ST 91-Ti VL-800
3607-ST - VL-3/8372-96-RH 203-96 204-96 9315 200DGS
275-ST 91-Ti VL-800
3607-ST - VL-3/8372-96-RH 203-96 204-96 9315 200DGS
275-ST 91-Ti VL-800
366-RHM 203-96 204-96 9365 275-ST 91-Ti VL-800 200DGS
375-ST 975-Ti VL-800372-96-RH 203-96-7/16 204-96 9705 200DGS
300-ST/10˚ 97-Ti/10˚ VL-10-3/8
— — —372-96-RH 203-96-7/16 204-96 9701 200DGS
— 980-Ti/10˚ VL-10-3/8
170
MARINE CAMS AND COMPONENTS
Small Block Chevy V-8 1.5:1 Rocker Ratio
NOTE: Additional Cam Profiles are available in each category to suit any special application requirements.Contact the Isky Factory Technical Department for assistance.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
Part No. Valve Valve Advertised .050 Lobe Cam Only Grind No./Type APPLICATION RPM-Range Lift Lash Hot Duration Duration Center
201262/270-12 262/270 HL 1800-4600 .435 .000 262° 208° 112° HYDRAULIC .445 .000 270° 216°
201264/271-12 264/270-MEGA 2000-4800 .450 .000 264° 214° 112° HYDRAULIC .465 .000 270° 221°
201271/281-12 270/280 MEGA 2200-5200 .465 .000 270° 221° 112° HYDRAULIC .485 .000 280° 232°
201042 Z-42 2500-5800 .525 .016 290° 254° 110° SOLID .520 .018 296° 260°
201604 RR-604 2800-6200 .600 .028 294° 260° 110° ROLLER .600 .028 300° 266°
Mild Performance. MercruiserI-O drive. Skiing, pleasure use.
Medium Performance.Mercruiser I-O drive. Skiing.
Maximum Performance.Mercruiser I-O drive.Combination Skiing. High perf.
Good all around performancefor V-drive, skiing.
Maximum performance forV-drive, high perf. lake use,skiing.
Part No. Valve Valve Advertised .050 Lobe Cam Only Grind No./Type APPLICATION RPM-Range Lift Lash Hot Duration Duration Center
311278/10 278 MEGA 2000-5400 .525 .000 278° 234° 110° HYDRAULIC .525 .000 278° 234°
311281/10 280 MEGA 2000-5500 .565 .000 280° 232° 110° HYDRAULIC .565 .000 280° 232°
Jet boat, A-B impeller. All arounduse. Skiing, pleasure use.
Jet boat, A-B impeller.Skiing and high performance use.
Oldsmobile 455 C.I. V-8 1.6:1 Rocker Ratio
Ford 429/460 C.I. V-8 1.75:1 Rocker Ratio
Part No. Valve Valve Advertised .050 Lobe Cam Only Grind No./Type APPLICATION RPM-Range Lift Lash Hot Duration Duration Center
691281/10 280 MEGA 2000-5400 .517 .000 280° 232° 110° HYDRAULIC .517 .000 280° 232°
Jet boat, A-B impeller. All aroundperf. use. Skiing, pleasure use.
171
MARINE CAMS AND COMPONENTS
Small Block Chevy V-8 Recommended Valve Train Components
◊ Not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
RetainersLifters Timing Set Pushrods Rocker Arms Valve Springs Steel Titanium Valve Locks Dist. Gear
Page 10-25 Page 56-57 Page 44-48 Page 49 ◊ Page 27-41 Page 42 Page 43 Page 53 Page 56
202-HY 200-TS 203-HG 204 205-D 707-ST — VL-32 200DGS
202-HY 200-TS 203-HG 204 205-D 707-ST — VL-32 200DGS
202-HY 200-TS 203-HG 204 205-D 707-ST — VL-32 200DGS
202-H 300-TS ◊ 203-HG 204 6005 507-ST 60-Ti VL-32 200DGS
507-STA — VL-321241-LSH — 1235-L 204 9005 200DGS
175-ST 91-Ti VL-700
Ford 429/460 C.I. V-8 Recommended Valve Train Components
RetainersLifters Timing Set Pushrods Rocker Arms Valve Springs Steel Titanium Valve Locks Dist. Gear
Page 10-25 Page 56-57 Page 44-48 Page 49 ◊ Page 27-41 Page 42 Page 43 Page 53 Page 56
507-STA - VL-32432-HY 310-TS 383-CHG 204-96 8005-A 310DG
175-ST 91-Ti VL-700
507-STA - VL-32432-HY 310-TS 383-CHG 204-96 8005-A 310DG
175-ST 91-Ti VL-700
Oldsmobile 455 C.I. V-8 Recommended Valve Train Components Retainers
Lifters Timing Set Pushrods Rocker Arms Valve Springs Steel Titanium Valve Locks Dist. GearPage 10-25 Page 56-57 Page 44-48 Page 49 ◊ Page 27-41 Page 42 Page 43 Page 53 Page 56
202-HY 690-TS 683-B — 6005 507-ST 60-Ti VL-32 —
172 NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
186°
194°
200°
208°
202°
208°
208°
214°
224°
242°
248°
248°
208°
228°
236°
248°
216°
224°
232°
240°
248°
240°
214°
234°
244°
224°
221°
224°
236°
232°
226°
244°
252°
236°
256°
248°
258°
204°
209°
217°
225°
234°
246°
204°
210°
218°
228°
238°
248°
258°
84°
100°
106°
113°
112°
116°
118°
122°
130°
111°
113°
129°
110°
121°
125°
134°
121°
126°
130°
136°
142°
151°
122°
141°
150°
134°
130°
135°
144°
142°
137°
153°
162°
144°
164°
158°
166°
116°
122°
131°
141°
150°
157°
113°
120°
129°
139°
150°
162°
171°
.400"
.425"
.435"
.445"
.453"
.464˝
.464˝
.469˝
.496˝
.387˝
.387˝
.416˝
419˝
.422˝
.422˝
.429˝
.440˝
.443˝
.443˝
.443˝
.449˝
.532˝
.480˝
.480˝
.480˝
.485˝
.496˝
.512˝
.512˝
.517˝
.522˝
.539˝
.539˝
.544˝
.560˝
.566˝
.592˝
.480˝
.496˝
.517˝
.539˝
.565˝
.586˝
.465˝
.480˝
.500˝
.520˝
.544˝
.573˝
.581˝
.375"
.400"
.408"
.417"
.425"
.435˝
.435˝
.440˝
.465˝
.363˝
.363˝
.390˝
.393˝
.396˝
.396˝
.402˝
.412˝
.415˝
.415˝
.415˝
.420˝
.500˝
.450˝
.450˝
.450˝
.454˝
.465˝
.480˝
.480˝
.485˝
.490˝
.505˝
.505˝
.510˝
.525˝
.530˝
.555˝
.450˝
.465˝
.485˝
.505˝
.530˝
.550˝
.435˝
.450˝
.468˝
.488˝
.510˝
.537˝
.544˝
.250˝
.266˝
.272˝
.278˝
.283˝
.290˝
.290˝
.293˝
.310˝
.242˝
.242˝
.260˝
.262˝
.264˝
.264˝
.268˝
.275˝
.277˝
.277˝
.277˝
.281˝
.333˝
.300˝
.300˝
.300˝
.303˝
.310˝
.320˝
.320˝
.323˝
.326˝
.337˝
.337˝
.340˝
.350˝
.354˝
.370˝
.300˝
.310˝
.323˝
.337˝
.353˝
.366˝
.290˝
.300˝
.312˝
.325˝
.340˝
.358˝
.363˝
TYPE OFCAM
LOBE SPECIFICATION CHART (HYDRAULIC & HYDRAULIC ROLLER)
LOBELIFT
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero LashRocker Arm Ratio
1.5 1.6 1.7
R.V.Hydraulic:.842" Dia.
HydraulicLift Rule:“OVALTRACK”.842" Dia.
PerformanceStreet,Strip,& OvalTrack:
.842" Dia.
HydraulicRoller:SmallBlockChevyV8
HydraulicRoller:Big BlockChevy V8andFord
302 HO V8
236°
248°
258°
262°
256°
258°
262°
270°
280°
288°
294°
296°
252°
268°
276°
296°
260°
264°
272°
280°
296°
286°
264°
278°
288°
268°
270°
280°
284°
280°
274°
292°
298°
284°
304°
296°
306°
252°
257°
265°
272°
282°
294°
252°
257°
265°
275°
284°
294°
305°
150°
162°
170°
175°
172°
176°
176°
183°
191°
205°
211°
212°
178°
195°
202°
213°
186°
193°
200°
207°
214°
209°
181°
202°
212°
193°
188°
192°
203°
199°
194°
211°
220°
203°
222°
214°
224°
172°
178°
185°
194°
201°
210°
172°
178°
185°
196°
206°
216°
226°
—
—
—
—
—
—
—
—
34°
—
—
—
—
—
—
—
—
—
—
—
—
74°
—
—
—
23°
38°
54°
60°
60°
61°
75°
83°
73°
92°
91°
101°
—
36°
56°
72°
86°
98°
—
—
42°
61°
80°
96°
103°
H-361
H-372
H-168
H-312
H-375
H-606
H-373
H-353
H-352
H-573
H-497
H-568
H-647
H-551
H-566
H-498
H-648
H-601
H-552
H-567
H-448
H-655
H-520
H-593
H-595
H-569
H-390
H-583
H-609
H-391
H-438
H-392
H-584
H-439
H-393
H-443
H-442
HR-524
HR-501
HR-500
HR-481
HR-474
HR-525
HR-542
HR-543
HR-544
HR-545
HR-546
HR-547
HR-636
.425"
.452"
.462"
.473"
.481"
.493˝
.493˝
.498˝
.527˝
.411˝
.411˝
.442˝
.445˝
.449˝
.449˝
.455˝
.467˝
.471˝
.471˝
.471˝
.477˝
.566˝
.510˝
.510˝
.510˝
.515˝
.527˝
.544˝
.544˝
.549˝
.554˝
.573˝
.573˝
.578˝
.595˝
.602˝
.629˝
.510˝
.527˝
.549˝
.573˝
.600˝
.622˝
.495˝
.510˝
.530˝
.552˝
.578˝
.608˝
.617˝
173NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
206º
212º
215º
218º
221º
224º
256º
227º
230º
233º
236º
250º
240º
243º
249º
254º
260º
214º
212º
210º
212º
214º
216º
240º
242º
244º
246º
224º
214º
218º
224º
227º
230º
236º
242º
242º
244º
246º
248º
248º
126º
131º
134º
136º
139º
142º
168º
145º
151º
154º
157º
166º
161º
163º
168º
174º
180º
124º
130º
127º
129º
131º
133º
157º
159º
161º
163º
146º
139º
143º
149º
152º
154º
159º
165º
164º
166º
168º
170º
170º
.553”
.561”
.566”
.570”
.575”
.578”
.581”
.585”
.592”
.595”
.598”
.600”
.605”
.610”
.612”
.629”
.638”
.493”
.525”
.532”
.532”
.532”
.532”
.578”
.578”
.578”
.578”
.581”
.600”
.605”
.608”
.608”
.612”
.615”
.620”
.650”
.650”
.650”
.650”
.670”
.325”
.330”
.333”
.335”
.338”
.340”
.342”
.344”
.348”
.350”
.352”
.353”
.356”
.359”
.360”
.370”
.375”
.290”
.309”
.313”
.313”
.313”
.313”
.340”
.340”
.340”
.340”
.342”
.353”
.356”
.358”
.358”
.360”
.362”
.365”
.382”
.382”
.382”
.382”
.394”
TYPE OFCAM
LOBE SPECIFICATION CHART (HYDRAULIC ROLLER) LATE MODEL LS-1 CHEVY V-8 EXPANSION TECHNOLOGY SERIES
LOBELIFT
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero Lash@ 1.7 ROCKER RATIO
LS-1Standard SeriesHydraulic Roller
1.450” Dia. Base Circle
254º
260º
263º
266º
269º
272º
300º
275º
278º
281º
284º
294º
288º
290º
296º
302º
308º
260º
260º
254º
256º
258º
260º
284º
286º
288º
290º
273º
264º
268º
274º
277º
280º
286º
292º
286º
288º
290º
292º
292º
176°
181º
184º
187º
190º
193º
225º
196º
200º
203º
206º
220º
210º
213º
219º
225º
231º
183º
183º
181º
183º
185º
187º
211º
213º
215º
217º
195º
184º
188º
194º
198º
201º
207º
212º
213º
215º
217º
219º
219º
56º
62º
65º
68º
71º
75º
97º
78º
86º
89º
93º
98º
97º
99º
104º
110º
116º
—
39º
45º
45º
46º
47º
85º
86º
87º
87º
79º
82º
86º
90º
93º
95º
98º
104º
110º
112º
113º
115º
118º
HR-674
HR-673
HR-740
HR-672
HR-741
HR-671
HR-731
HR-742
HR-675
HR-743
HR-676
HR-730
HR-744
HR-670
HR-669
HR-677
HR-678
HR-887
HR-848
HR-800
HR-801
HR-802
HR-803
HR-804
HR-805
HR-806
HR-807
HR-815
HR-813
HR-814
HR-816
HR-837
HR-817
HR-818
HR-819
HR-808
HR-809
HR-810
HR-811
HR-812
LS-1NEW HRXMax Area Lift
Curve Series Hy-draulic Roller
1.450” Dia.Base Circle
174 NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
H-893H-894H-895H-749H-738H-737H-835H-836H-897H-838H-735H-736H-700H-851H-852H-881H-880HR-878HR-853HR-745HR-854HR-746HR-759HR-760HR-761HR-861HR-862HR-762HR-763HR-764HR-682HR-683HR-680HR-726HR-681HR-856HR-857HR-888HR-889HR-890HR-891HR-892HR-885HR-886S-863S-769S-770S-903S-904S-758S-879S-782S-868S-882S-755S-756S-757
.425”
.425”
.425”
.442”
.476”
.476’
.476”
.476”
.476”
.510”
.510”
.510”
.544”
.568”
.568”
.607”
.617”
.493”
.537”
.554”
.578”
.595”
.634”
.634”
.634”
.473”
.473”
.632”
.632”
.632”
.632”
.632”
.632”
.632”
.632”
.632”
.632”
.680”
.680”
.680”
.680”
.680”
.680”
.680”
.357”
.452”
.452”
.493”
.500”
.510”
.585”
.588”
.605”
.608”
.651”
.658”
.663”
250º256º264º262º276º284º286º290º294º274º284º292º290º280º284º300º304º268º272º256º276º266º270º274º278º291º296º282º286º290º294º298º302º306º310º314º320º298º302º306º310º314º318º322º232º258º261º273º254º276º264º298º298º278º312º318º324º
202º208º216º215º236º244º246º250º254º230º240º248º244º242º246º252º256º220º218º209º222º222º222º226º230º241º246º236º240º244º248º252º256º260º264º268º274º246º250º254º258º262º266º270º200º226º229º234º226º244º236º264º264º246º276º280º284º
.250”
.250”
.250”
.260”
.280”
.280”
.280”
.280”
.280”
.300”
.300”
.300”
.320”
.334”
.334”
.357”
.363”
.290”
.316”
.326”
.340”
.350”
.373”
.373”
.373”
.278”
.278”
.372”
.372”
.372”
.372”
.372”
.372”
.372”
.372”
.372”
.372”
.400”
.400”
.400”
.400”
.400”
.400”
.400”
.210”
.266”
.266”
.290”
.294”
.300”
.344”
.346”
.356”
.358”
.383”
.387”
.390”
LOBE SPECIFICATION CHART HYDRAULIC, HYDRAULIC ROLLER & SOLID LIFTER (EXPANSION TECHNOLOGY SERIES)
96º99º103º104º134º140º142º146º150º139º147º154º152º153º157º162º165º125º131º126º140º142º144º149º154º135º139º152º156º160º164º168º172º175º179º185º191º166º170º174º178º182º186º189º49º117º120º132º132º146º149º172º170º158º185º189º193º
————————————61º77º79º95º100º—48º56º74º78º92º96º100º——93º97º101º105º108º112º114º116º120º124º116º119º122º125º128º131º133º——————81º95º100º94º121º125º129º
.375”
.375”
.375”
.390”
.420”
.420”
.420”
.420”
.420”
.450”
.450”
.450”
.480”
.501”
.501”
.536”
.545”
.435”
.474”
.489”
.510”
.525”
.560”
.560”
.560”
.417”
.417”
.558”
.558”
.558”
.558”
.558”
.558”
.558”
.558”
.558”
.558”
.600”
.600”
.600”
.600”
.600”
.600”
.600”
.315”
.399”
.399”
.435”
.441”
.450”
.516”
.520”
.534”
.537”
.575”
.580”
.585”
LOBELIFT
169º174º181º177º204º211º214º218º222º199º208º216º212º212º216º219º223º187º186º177º191º192º191º196º200º206º211º204º208º212º216º220º224º228º232º237º243º214º218º222º227º231º235º238º160º190º193º198º195º210º205º231º229º215º242º246º250º
.400”
.400”
.400”
.416”
.448”
.448”
.448”
.448”
.448”
.480”
.480”
.480”
.512”
.534”
.534”
.571”
.581”
.464”
.506”
.522”
.544”
.560”
.597”
.597”
.597”
.445”
.445”
.595”
.595”
.595”
.595”
.595”
.595”
.595”
.595”
.595”
.595”
.640”
.640”
.640”
.640”
.640”
.640”
.640”
.336”
.426”
.426”
.464”
.470”
.480”
.550”
.553”
.570”
.573”
.613”
.619”
.624”
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero LashRocker Arm Ratio
1.5 1.6 1.7
TYPE OFCAM
Oval Track;Hydraulic Lift Rule
.842” Dia Lifter
Hydraulic Roller
Small BlockChevy V-8
1.100” Dia.Base Circle
Hydraulic Roller
Big Block Chevyand Ford 302 HO V-8
1.200” Dia.Base Circle
Street/Drag Oval Track; Solid Lifter .842 Dia.
Valve Lash Hot:.014” Int.016” Ex
175NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
*SOLID LIFTER:.842" Dia.Oval Track
S-50E4
S-99+10
S-66
S-84
S-598
ZM-89
S-293
S-302
S-364
S-336
S-344
S-346
S-650
S-643
S-574
S-604
S-404
S-564
S-565
S-550
S-599
S-385
S-521
S-613
S-480
S-539
S-396
S-387
S-447
S-537
S-652
S-635
S-633
S-632
S-645
S-621
S-630
S-654
S-642
S-653
S-644
S-585
S-611
S-634
S-528
S-522
S-505
S-523
S-504
.481˝
.481˝
.506˝
.506˝
.544˝
.544˝
.544˝
.620˝
.634˝
.634˝
.646˝
.663˝
.544˝
.544˝
.561˝
.568˝
.574˝
.580˝
.588˝
.595˝
.595˝
.595˝
.605˝
.617˝
.620˝
.620˝
.620˝
.629˝
.636˝
.646˝
.598˝
.605˝
.617˝
.629˝
.640˝
.656˝
.663˝
.586˝
.595˝
.606˝
.569˝
.646˝
.656˝
.660˝
.666˝
.670˝
.685˝
.685˝
.692˝
256°
260°
264°
286°
272°
278°
290°
304°
314°
330°
320°
330°
282°
286°
276°
286°
282°
288°
294°
278°
285°
288°
282°
284°
288°
288°
292°
296°
302°
306°
270°
274°
278°
282°
286°
290°
294°
276°
280°
284°
274°
288°
292°
286°
296°
300°
304°
308°
312°
210°
216°
228°
250°
238°
244°
250°
264°
272°
286°
274°
284°
254°
258°
242°
252°
247°
254°
260°
244°
251°
254°
248°
251°
254°
258°
259°
263°
268°
272°
242°
246°
250°
254°
258°
262°
266°
248°
252°
256°
247°
258°
262°
258°
266°
270°
274°
278°
282°
.283”
.283”
.298”
.298”
.320”
.320”
.320”
.365”
.373”
.373”
.380”
.390”
.320”
.320”
.330”
.334”
.338”
.341”
.346”
.350”
.350”
.350”
.356”
.363”
.365”
.365”
.365”
.370”
.374”
.380”
.352”
.356”
.363”
.370”
.376”
.386”
.390”
.345”
.350”
.357”
.335”
.380”
.386”
.388”
.392”
.394”
.403”
.403”
.407”
LOBE SPECIFICATION CHART (SOLID LIFTER) STREET, DRAG & OVAL TRACK
121°
118°
133°
144°
140°
157°
156°
166°
174°
189°
178°
186°
160°
164°
148°
158°
154°
158°
164°
152°
158°
161°
156°
160°
162°
168°
164°
171°
178°
181°
154°
158°
162°
166°
170°
172°
176°
161°
165°
169°
161°
168°
173°
173°
177°
182°
187°
191°
195°
—
—
—
—
56°
64°
68°
102°
110°
121°
116°
125°
64°
68°
74°
78°
79°
84°
90°
85°
87°
90°
89°
94°
97°
102°
98°
108°
112°
117°
88°
92°
98°
104°
108°
112°
116°
89°
95°
101°
82°
108°
113°
115°
118°
122°
128°
132°
136°
.425˝
.425˝
.448˝
.448˝
.480˝
.480˝
.480˝
.548˝
.560˝
.560˝
.570˝
.585˝
.480˝
.480˝
.495˝
.501˝
.507˝
.512˝
.520˝
.525˝
.525˝
.525˝
.534˝
.544˝
.547˝
.547˝
.547˝
.555˝
.560˝
.570˝
.528˝
.534˝
.545˝
.555˝
.565˝
.580˝
.585˝
.517˝
.525˝
.535˝
.502˝
.570˝
.580˝
.582˝
.588˝
.590˝
.604˝
.604˝
.610˝
LOBELIFT
180°
183°
193°
213°
202°
223°
216°
225°
232°
246°
236°
244°
222°
226°
207°
218°
212°
218°
224°
209°
217°
220°
214°
216°
219°
225°
223°
229°
234°
238°
210°
214°
218°
223°
227°
228°
232°
218°
222°
226°
217°
224°
228°
228°
232°
237°
241°
245°
249°
.453˝
.453˝
.477˝
.477˝
.512˝
.512˝
.512˝
.584˝
.597˝
.597˝
.608˝
.624˝
.512˝
.512˝
.528˝
.534˝
.541˝
.546˝
.553˝
.560˝
.560˝
.560˝
.570˝
.581˝
.584˝
.584˝
.584˝
.592˝
.598˝
.608˝
.563˝
.570˝
.580˝
.592˝
.602˝
.617˝
.624˝
.552˝
.560˝
.571˝
.536˝
.608˝
.617˝
.621˝
.627˝
.630˝
.645˝
.645˝
.651˝
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero LashRocker Arm Ratio
1.5 1.6 1.7
TYPE OFCAM
SOLIDLIFTER:.842" DIA.Street Perf.Valve LashHot .020"
SOLIDLIFTER:.842" Dia.
Bracket RaceDrags
SOLIDLIFTER:.842" Dia.Oval TrackValve
Lash Hot.016" INT.018" EX.
SOLID LIFTER:.842" Dia.
MAGNUM-XLOval Track Se-
ries:Valve Lash Hot.014" INT.016" EX
SOLID LIFTER:NASCAR .875"Dia. Oval Track
Series:Valve
Lash Hot .014"INT .016" EX
* New; Longer life, Tru radius “Bullnose” grinds: 35% smoother over the nose. (Excellent for higher ratio rockers)
176 NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
LOBE SPECIFICATION CHART 1.000” BASE CIRCLE .750” DIA. ROLLER BEARING (OVAL TRACK ROLLER)
.376”
.376"
.376"
.393"
.393"
.393"
.400"
.400"
.400"
.400"
.400"
.400"
.410"
.410"
.410"
.410"
.411"
.411"
.420"
.420"
.420"
.420"
.420"
.420"
.420"
.420"
.420"
.430"
.430”
.430”
.430"
.430"
.430"
.430"
.430"
.433"
.433"
.433”
.433”
.433"
.433"
.433"
.433"
.440"
.446"
294 Deg.
300 Deg.
312 Deg.
294 Deg.
300 Deg.
314 Deg.
284 Deg.
290 Deg.
294 Deg.
300 Deg.
304 Deg.
308 Deg.
288 Deg.
294 Deg.
298 Deg.
300 Deg.
302 Deg.
308 Deg.
286 Deg.
290 Deg.
298 Deg.
304 Deg.
304 Deg.
306 Deg.
310 Deg.
314 Deg.
318 Deg.
290 Deg.
292 Deg.
294 Deg.
296 Deg.
298 Deg.
302 Deg.
306 Deg.
310 Deg.
282 Deg.
286 Deg.
288 Deg.
290 Deg.
292 Deg.
294 Deg.
298 Deg.
302 Deg.
290 Deg.
294 Deg.
260°
266°
278°
260°
266°
280°
252°
256°
260°
266°
270°
274°
254°
260°
264°
266°
268°
274°
254°
258°
264°
268°
270°
272°
276°
280°
282°
256°
258°
260°
262°
264°
268°
272°
276°
252°
256°
258°
260°
262°
264°
268°
272°
260°
264°
226°
232°
244°
226°
232°
246°
218°
223°
228°
233°
236°
240°
221°
226°
230°
233°
235°
241°
222°
226°
232°
236°
240°
242°
243°
247°
248°
223°
225°
227°
229°
231°
234°
238°
243°
221°
225°
227°
229°
231°
233°
237°
241°
228°
234°
173°
177°
186°
174°
180°
192°
168°
172°
176°
181°
184°
187°
172°
177°
181°
183°
185°
189°
174°
177°
183°
185°
188°
190°
191°
194°
195°
175°
177°
178°
180°
182°
185°
189°
192°
175°
179°
181°
183°
185°
187°
191°
195°
180°
186°
112°
116°
120°
117°
123°
131°
116°
119°
122°
125°
128°
130°
122°
126°
128°
130°
132°
135°
125°
128°
133°
133°
135°
137°
138°
140°
141°
128°
129°
130°
132°
133°
136°
138°
141°
130°
134°
136°
137°
139°
141°
145°
149°
132°
139°
R–561
R–562
R–559
R–555
R–503
R–560
R–582
R–554
R–548
R–534
R–533
R–479
R–514
R–494
R–553
R–571
R–493
R–515
R–558
R–581
R–556
R–590
R–535
R-651
R–467
R–469
R–470
R–586
R-661
R–575
R-663
R–576
R–577
R–578
R–587
R-627
R–625
R-667
R–624
R-668
R–623
R–626
R–649
R–607
R–518
.564”
.564”
.564”
.590”
.590”
.590”
.600”
.600”
.600”
.600”
.600”
.600”
.615”
.615”
.615”
.615”
.616”
.616”
.630”
.630”
.630”
.630”
.630”
.630”
.630”
.630”
.630”
.645”
.645”
.645”
.645”
.645”
.645”
.645”
.645”
.650”
.650”
.650”
.650”
.650”
.650”
.650”
.650”
.660”
.670”
.602”
.602”
.602”
.629”
.629”
.629”
.640”
.640”
.640”
.640”
.640”
.640”
.656”
.656”
.656”
.656”
.657”
.657”
.672”
.672”
.672”
.672”
.672”
.672”
.672”
.672”
.672”
.688”
.688”
.688”
.688”
.688”
.688”
.688”
.688”
.693”
.693”
.693”
.693”
.693”
.693”
.693”
.693”
.704”
.713”
.639”
.639”
.639”
.668”
.668”
.668”
.680”
.680”
.680”
.680”
.680”
.680”
.697”
.697”
.697”
.697”
.698”
.698”
.714”
.714”
.714”
.714”
.714”
.714”
.714”
.714”
.714”
.731”
.731”
.731”
.731”
.731”
.731”
.731”
.731”
.736”
.736”
.736”
.736”
.736”
.736”
.736”
.736”
.748”
.758”
LOBELIFT
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero LashRocker Arm Ratio
1.5 1.6 1.7
TYPE OFCAM
Oval TrackRoller:
Valve LashHot .028"
Oval TrackRoller:
“Accelerator”Intake Profiles.
Valve Lash Hot .024"
Oval TrackRoller Intake ValveLash Hot .018"
177NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
LOBE SPECIFICATION CHART (OVAL TRACK) ROLLER: EXPANSION TECHNOLOGY SERIES
.376”
.376"
.376"
.376"
.376"
.376"
.376"
.376"
.393”
.400”
.400”
.400”
.405”
.410”
.411”
.411”
.420”
.420”
.420”
.420”
.420”
.430”
.430”
.430”
.433”
.433”
.433”
.433”
.446”
.446”
.446”
.446”
.446”
.446”
.446”
.450”
.410”
.410”
.420”
.420”
.420”
.420”
.430”
.430”
.430”
.430”
.430”
.433”
.433”
.433”
.433”
.440”
.446”
.450”
272º
276º
280º
286º
290º
304º
308º
316º
292º
276º
280º
298º
302º
290º
306º
310º
288º
292º
294º
298º
308º
300º
304º
308º
296º
300º
304º
306º
284º
288º
292º
292º
296º
298º
302º
280º
298º
302º
286º
290º
296º
300º
290º
294º
298º
302º
306º
286º
290º
294º
298º
311º
300º
298º
238º
242º
246º
252º
256º
270º
274º
282º
258º
244º
248º
264º
268º
256º
272º
276º
256º
260º
262º
266º
274º
266º
270º
274º
266º
270º
274º
276º
253º
258º
261º
262º
266º
268º
272º
250º
264º
268º
254º
258º
264º
268º
260º
264º
268º
272º
276º
256º
260º
264º
268º
272º
270º
265º
205º
209º
213º
219º
223º
236º
240º
248º
226º
212º
215º
232º
236º
223º
239º
243º
224º
228º
230º
234º
242º
232º
236º
240º
235º
239º
243º
245º
221º
227º
229º
232º
234º
238º
242º
220º
231º
235º
223º
227º
233º
237º
230º
234º
238º
242º
246º
226º
230º
234º
238º
238º
240º
235º
151º
154º
160º
165º
170º
180º
183º
189º
175º
161º
164º
179º
185º
174º
187º
191º
176º
179º
181º
184º
190º
183º
187º
191º
189º
193º
197º
199º
174º
179º
181º
184º
186º
190º
194º
177º
182º
186º
175º
180º
186º
191º
181º
186º
191º
195º
199º
181º
185º
190º
194º
188º
194º
189º
94º
96º
100º
105º
109º
118º
120º
124º
119º
109º
113º
124º
130º
124º
134º
137º
127º
130º
132º
133º
137º
134º
137º
140º
143º
147º
151
153º
129º
131º
134º
137º
137º
143º
147º
135º
130º
134º
127º
131º
137º
141º
132º
136º
140º
144º
148º
135º
139º
143º
147º
139º
146º
144º
R-867
R-855
R-859
R-777
R-858
R-709
R-710
R-711
R-797
R-865
R-866
R-712
R-798
R-716
R-717
R-718
R-720
R-721
R-722
R-723
R-724
R-687
R-688
R-689
R-701
R-702
R-703
R-704
R-697
R-686
R-698
R-706
R-685
R-707
R-708
R-860
R-820
R-821
R-822
R-823
R-824
R-825
R-826
R-827
R-828
R-829
R-830
R-831
R-832
R-833
R-834
R-899
R-839
R-898
.564”
.564”
.564”
.564”
.564”
.564”
.564”
.564”
.590”
.600”
.600”
.600”
.607”
.615”
.616”
.616”
.630”
.630”
.630”
.630”
.630”
.645”
.645”
.645”
.650”
.650”
.650”
.650”
.670”
.670”
.670”
.670”
.670”
.670”
.670”
.675”
.615”
.615”
.630”
.630”
.630”
.630”
.645”
.645”
.645”
.645”
.645”
.650”
.650”
.650”
.650”
.660”
.670”
.675”
.602”
.602”
.602”
.602”
.602”
.602”
.602”
.602”
.629”
.640”
.640”
.640”
.648”
.656”
.657”
.657”
.672”
.672”
.672”
.672”
.672”
.688”
.688”
.688”
.693”
.693”
.693”
.693”
.713”
.713”
.713”
.713”
.713”
.713”
.713”
.720”
.656”
.656”
.672”
.672”
.672”
.672”
.688”
.688”
.688”
.688”
.688”
.693”
.693”
.693”
.693”
.704”
.713”
.720”
.639”
.639”
.639”
.639”
.639”
.639”
.639”
.639”
.668”
.680”
.680”
.680”
.688”
.697”
.698”
.698”
.714”
.714”
.714”
.714”
.714”
.731”
.731”
.731”
.736”
.736”
.736”
.736”
.758”
.758”
.758”
.758”
.758”
.758”
.758”
.765”
.697”
.697”
.714”
.714”
.714”
.714”
.731”
.731”
.731”
.731”
.731”
.736”
.736”
.736”
.736”
.748”
.758”
.765”
LOBELIFT
ADVERTISEDDURATION
.050DUR
.100DUR
.200DUR
.300DUR
MASTERNo.
Valve Lift With Zero LashRocker Arm Ratio
1.5 1.6 1.7
TYPE OFCAM
Standard BearingCore: .750” Dia.Roller Brg
1.000” Base Circle
Valve Lash Hot.024”
55-MM Core.750” Dia.Roller Brg
1.275” Base Circle
Valve Lash Hot.024”
178 NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
LOBE SPECIFICATION CHART (STREET & DRAG RACE) “ROLLER” .750” DIA ROLLER BRG.LOBELIFT
ADVERTISEDDURATION
.050DUR 1.5 1.6 1.7
Valve Lift With Zero LashRocker Arm Ratio
MASTERNo.
.300DUR
.200DUR
.100DUR
STREETROLLER:
VALVE LASHHOT .028˝
TYPE OFCAM
DRAGRACE
ROLLER:VALVE LASHHOT .028˝
.323”
.329”
.350”
.354”
.380”
.385”
.376”
.376”
.393”
.393”
.400”
.400”
.400”
.400”
.410”
.410”
.410”
.411”
.411”
.420”
.420”
.420”
.420”
.420”
.420”
.420”
.427”
.427”
.427”
.427”
.427”
.427”
.430”
.430”
.430”
.440”
.440”
.440”
.443”
.443”
.450”
.450”
.450”
.450”457”457”457”457”460”460”460”460”464”470”470”472”475”480”490”497”506”507”520”
278°284°280°290°290°284°300°312°300°314°300°300°304°308°300°334°338°302°308°304°310°314°318°320°322°326°302°306°310°314°318°320°302°306°310°306°322°326°314°318°318°322°324°334°332°336°344°354°308°314°318°350°321°324°318°326°332°332°326°334°332°342°334°
234°242°240°246°250°244°266°278°266°280°260°266°270°274°270°298°302°268°274°270°276°280°282°286°290°294°268°272°276°280°282°286°268°272°276°274°290°294°282°286°286°290°292°298°288°292°304°314°276°282°286°310°290°282°286°295°288°300°288°294°300°302°294°
197°208°206°212°215°211°232°244°232°246°225°233°236°240°238°263°266°235°241°240°243°247°248°252°257°261°236°239°243°248°249°253°234°238°243°242°258°261°250°254°254°257°259°264°251°255°266°278°244°250°254°274°258°247°254°262°252°267°254°260°268°267°260°
138°149°153°157°162°160°177°186°180°192°173°181°184°187°188°206°209°185°189°188°191°194°195°200°205°208°185°189°192°196°197°201°185°189°192°193°207°210°200°204°204°206°207°210°200°204°213°224°195°200°204°221°208°198°205°213°203°218°206°211°221°218°213°
60°69°87°91°107°106°116°120°123°131°120°125°128°130°134°146°148°132°135°135°138°140°141°144°148°151°136°138°140°144°145°148°136°138°141°144°155°157°150°153°153°154°156°158°152°155°164°169°148°152°155°169°160°153°157°165°157°171°162°167°175°174°171°
R-549R-516R-483R-259R-359R-412R-562R-559R-503R-560R-358R-534R-533R-479R-486R-512R-580R-493R-515R-535R-467R-469R-470R-468R-471R-509R-417R-424R-426R-414R-427R-466R-577R-578R-587R-527R-508R-499R-473R-472R-495R-511R-536R-513R-406R-400R-517R-489R-592R-507R-506R-488R-453R-409R-510R-452R-487R-454R-456R-455R-482R-441R-440
.484˝
.493˝
.525˝
.531˝
.570˝
.578˝
.564˝
.564˝
.590˝
.590˝
.600˝
.600˝
.600˝
.600˝
.615˝
.615˝
.615˝
.616˝
.616˝
.630˝
.630˝
.630˝
.630˝
.630˝
.630˝
.630˝
.640˝
.640˝
.640˝
.640˝
.640˝
.640˝
.645˝
.645˝
.645˝
.660˝
.660˝
.660˝
.664˝
.664˝
.675˝
.675˝
.675˝
.675˝
.686˝
.686˝
.686˝
.686˝
.690˝
.690˝
.690˝
.690˝
.696˝
.705˝
.705˝
.708˝
.712˝
.720˝
.735˝
.745˝
.759˝
.760˝
.780˝
.517˝
.526˝
.560˝
.566˝
.608˝
.616˝
.602˝
.602˝
.629˝
.629˝
.640˝
.640˝
.640˝
.640˝
.656˝
.656˝
.656˝
.657˝
.657˝
.672˝
.672˝
.672˝
.672˝
.672˝
.672˝
.672˝
.683˝
.683˝
.683˝
.683˝
.683˝
.683˝
.688˝
.688˝
.688˝
.704˝
.704˝
.704˝
.708˝
.708˝
.720˝
.720˝
.720˝
.720˝
.731˝
.731˝
.731˝
.731˝
.736˝
.736˝
.736˝
.736˝
.742˝
.752˝
.752˝
.755˝
.760˝
.768˝
.784˝
.795˝
.809˝
.811˝
.832˝
.549˝
.559˝
.595˝
.602˝
.646˝
.654˝
.639˝
.639˝
.668˝
.668˝
.680˝
.680˝
.680˝
.680˝
.697˝
.697˝
.697˝
.698˝
.698˝
.714˝
.714˝
.714˝
.714˝
.714˝
.714˝
.714˝
.726˝
.726˝
.726˝
.726˝
.726˝
.726˝
.731˝
.731˝
.731˝
.748˝
.748˝
.748˝
.753˝
.753˝
.765˝
.765˝
.765˝
.765˝
.777˝
.777˝
.777˝
.777˝
.782˝
.782˝
.782˝
.782˝
.789˝
.799˝
.799˝
.802˝
.807˝
.816˝
.833˝
.845˝
.860˝
.862˝
.884˝
179NOT LEGAL FOR SALE OR USE ON POLLUTION-CONTROLLED MOTOR VEHICLES
LOBE SPECIFICATION CHART (DRAG RACE) ROLLER: EXPANSION TECHNOLOGY SERIESLOBELIFT
ADVERTISEDDURATION
.050DUR 1.5 1.6 1.7
Valve Lift With Zero LashRocker Arm Ratio
MASTERNo.
.300DUR
.200DUR
.100DUR
Small BlockChevy V-8: Std.Bearing Core..750” Dia RollerBrg. 1.000” Base
Circle
Valve Lash Hot.024”
TYPE OFCAM
Big BlockChevy V-8: Std.Bearing Core..750” Dia.Roller Brg.1.100” BaseCircle
Valve Lash Hot.024”
Small & Big Block Chevy V-8:
55-MM Core.850” Dia RollerBrg. 1.275”Base circle
Valve Lash Hot.024”
.400”
.400”
.400”
.411”
.420”
.430”
.430”
.430”
.430”
.430”
.430”
.440”
.450”
.450”
.450”
.450”
.460”
.470”
.471”
.475”
.475”
.475”
.475”
.480”
.480”
.483”
.483”
.483”
.484”
.488”
.505”
.506”
.508”
.510”
.527”
.460”
.464”
.470”
.470”
.475”
.475”
.487”
.496”
.500”
.508”
.510”
.510”
.510”
.524”
.524”
.527”
312º
316º
320º
314º
312º
312º
314º
316º
318º
320º
324º
310º
320º
332º
328º
336º
328º
322º
346º
310º
318º
318º
348º
328º
356º
320º
328º
332º
306º
323º
324º
342º
358º
320º
322º
328º
322º
304º
310º
348º
354º
310º
320º
340º
358º
318º
328º
340º
312º
318º
323º
278º
282º
286º
280º
278º
278º
280º
282º
284º
286º
290º
278º
292º
297º
298º
308º
284º
290º
304º
282º
284º
288º
306º
290º
316º
284º
292º
296º
268º
283º
292º
310º
317º
288º
290º
296º
290º
274º
280º
306º
314º
276º
286º
300º
318º
288º
292º
300º
279º
286º
291º
244º
248º
252º
247º
245º
245º
247º
249º
251º
253º
257º
246º
261º
262º
267º
277º
247º
258º
269º
251º
250º
257º
270º
257º
279º
248º
257º
261º
234º
250º
260º
278º
279º
257º
257º
263º
258º
244º
250º
271º
275º
244º
252º
264º
281º
258º
255º
263º
244º
254º
259º
191º
195º
199º
195º
193º
194º
196º
198º
200º
202º
206º
197º
214º
212º
220º
227º
200º
209º
216º
205º
201º
211º
221º
209º
228º
199º
208º
213º
190º
203º
214º
231º
227º
214º
212º
215º
211º
199º
205º
223º
223º
198º
206º
213º
230º
214º
208º
212º
197º
209º
215º
134º
138º
142º
141º
139º
143º
145º
147º
149º
151º
155º
148º
164º
160º
170º
174º
155º
161º
165º
160º
155º
166º
174º
162º
179º
155º
164º
168º
150º
158º
172º
186º
181º
174º
172º
166º
165º
156º
162º
176º
174º
156º
162º
168º
184º
174º
167º
169º
157º
170º
175º
R-713
R-714
R-715
R-719
R-725
R-690
R-691
R-692
R-693
R-694
R-768
R-695
R-791
R-728
R-792
R-793
R-850
R-696
R-739
R-788
R-729
R-789
R-790
R-901
R-849
R-732
R-778
R-779
R-771
R-900
R-874
R-875
R-734
R-794
R-735
R-884
R-883
R-766
R-767
R-795
R-786
R-781
R-752
R-783
R-734
R-796
R-785
R-748
R-747
R-765
R-733
.600”
.600”
.600”
.616”
.630”
.645”
.645”
.645”
.645”
.645”
.645”
.660”
.675”
.675”
.675”
.675”
.690”
.705”
.707”
.713”
.713”
.713”
.713”
.720”
.720”
.725”
.725”
.725’
.726”
.732”
.758”
.759”
.762”
.765”
.791”
.690”
.696”
.705”
.705”
.713”
.713”
.731”
.744”
.750”
.762”
.765”
.765”
.765”
.786”
.786”
.791”
.640”
.640”
.640”
.657”
.672”
.688”
.688”
.688”
.688”
.688”
.688”
.704”
.720”
.720”
.720”
.720”
.736”
.752”
.754”
.760”
.760”
.760”
.760”
.768”
.768”
.773”
.773”
.773”
.774”
.781”
.808”
.810”
.813”
.816”
.843”
.736”
.742”
.752”
.752”
.760”
.760”
.779”
.794”
.800”
.813”
.816”
.816”
.816”
.838”
.838”
.843”
.680”
.680”
.680”
.698”
.714”
.731”
.731”
.731”
.731”
.731”
.731”
.748”
.765”
.765”
.765”
.765”
.782”
.799”
.801”
.808”
.808”
.808”
.808”
.816”
.816”
.821”
.821”
.821”
.822”
.830”
.859”
.860”
.864”
.867”
.896”
.782”
.789”
.799”
.799”
.808”
.808”
.828”
.843”
.850”
.864”
.867”
.867”
.867”
.890”
.890”
.896”
180
181
BMC •
RACING CAMS*NOTE: CAMS NOT AVAILABLE OUTRIGHT.
“A” TYPE4 Cyl. OHV Engines AUSTIN-HEALY SPRITE
Sprite - Morris Minor - Mini - Cooper - Midget850, 948, 970, 997, 998, 1070, 1098 & 1275 CC
VALVE GRIND GRIND VALVE LASH ADVERTISED .050 CUSTOMERS NO. TYPE INTAKE EXHAUST LIFT HOT DURATION DURATION CAM
MM-32 TORQUER 22-56 59-25 B
MM-55 COMBINATION 25-59 59-25 A
MM-66 COMPETITION 36-70 70-36 A
MM-88 MAX. COMP 43-77 77-43 A
MM-99 MAX. COMP 53-87 87-53 A
.330 .016 258O 221O
.325 .019 264O 228O
.325 .016 264O 228O
.325 .019 264O 228O
.325 .020 286O 250O
.325 .020 286O 250O
.405 .025 300O 254O
.405 .025 300O 254O
.405 .025 320O 262O
.405 .025 320O 262O
ASSEMBLY KIT COMPONENTS (STREET & COMPETITION)
VWE-005 8 SILICON CHROME OUTER VALVE SPRINGSSP-006 8 SILICON CHROME INNER VALVE SPRINGSSP-003 8 CHROME MOLY TUBULAR PUSHRODS (850-1098CC)SP-013 8 CHROME MOLY PUSHRODS (1275CC)SP-007 8 ALUMINUM VALVE SPRING RETAINERS
(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS)
COMPETITION ASSEMBLY KIT (SUPER COMPETITION)
VWE-005 8 SILICON CHROME OUTER VALVE SPRINGSSP-116 8 SILICON CHROME INNER VALVE SPRINGSSP-003 8 CHROME MOLY TUBULAR PUSHRODS (850-1098CC)SP-013 8 CHROME MOLY PUSHRODS (1275CC)SP-007 8 ALUMINUM VALVE SPRING RETAINERS
DATSUN • 1600cc L-16 : 1800cc L-18 & NEW 2000cc L-20 4 Cyl. SOHC Engines
RACING CAMS*NOTE: Thicker valve lash caps are required for correct geometry(order by Part # listed below).
ASSEMBLY KIT7005 (8) 8 PAIR SPECIAL ALLOY DUAL VALVE SPRINGS1624-ST (8) 8 STEEL VALVE SPRING RETAINERS
VALVE VALVE GRIND OUTRIGHT GRIND LASH CAP VALVE LASH ADVERTISED .050 CUSTOMERS PART NO. NO. PART NO. TYPE INTAKE EXHAUST LIFT COLD DURATION DURATION CAM
710147 L-475 LC-175 STAGE I 26-64 64-26 .475 270° 222° A
710148 L-480 LC-175 STAGE II 31-69 69-31 .480 280° 232° A
710149 L-490 LC-175 STAGE III 36-74 74-36 .490 290° 242° A
710196 Z-196 LC-263 COMPETITION 51-75 75-51 .530 .010 306° 264° A
710127 Z-273 LC-263 COMPETITION 51-75 75-51 .595 .010 306° 274° A
.006 .008
.008 .010
.010 .012
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
DATSUN • 6 Cyl. SOHC
RACING CAMS*NOTE: Thicker valve lash caps are required for correct rocker arm geometry(order by Part # listed below).
L-24 Engine 2400cc (240-Z) & 2600cc (260-Z) & 2800cc (280-Z)
ENGINE: 240Z 260-280ZSTAGE I HIGHER LIFT THAN STOCK CAM HIGHER LIFT BUT SLIGHTLY (SAME DURATION) SHORTER DURATION THAN STOCK CAMSTAGE II HIGHER LIFT + 10° DURATION HIGHER LIFT THAN STOCK CAM OVER STOCK (SAME DURATION)STAGE III HIGHER LIFT + 20° DURATION HIGHER LIFT + 10° DURATION OVER STOCK STOCK
ASSEMBLY KIT
7005 (12) 12 PAIR SPECIAL ALLOY DUAL VALVE SPRINGS1624-ST(12) 12 STEEL VALVE SPRING RETAINERS
(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.)
240Z/260Z 280Z VALVE VALVE GRIND OUTRIGHT OUTRIGHT GRIND LASH CAP VALVE LASH ADVERTISED .050 CUSTOMERS PART NO. PART NO. NO. PART NO. TYPE INTAKE EXHAUST LIFT COLD DURATION DURATION CAM
715147 718147 L-475 LC-175 STAGE I 26-64 64-26 .475 270° 222° B
715148 718148 L-480 LC-175 STAGE II 31-69 69-31 .480 280° 232° B
715149 718149 L-490 LC-175 STAGE III 36-74 74-36 .490 290° 242° B
715196 718196 Z-196 LC-263 COMPETITION 51-75 75-51 .530 .010 306° 264° B
715127 718127 Z-273 LC-263 COMPETITION 51-75 75-51 .595 .010 306° 274° B
.006 .008
.008 .010
.010 .012
FORD ANGLIA *PINTO & FIESTA105E, 109E, 116Eand Cortina
1600 Engine
*NOTE: This is the only cam thatmay be in- stalled without notchingthe piston on the ‘67 and later 1600GT engine with crossflow heads anddish-top pistons. This engine alsocomes in the Ford Pinto. These engines take the #453 pushrod.
OUTRIGHT VALVE GRIND PART GRIND VALVE LASH ADVERTISED CUSTOMERS NO. NO. TYPE INTAKE EXHAUST LIFT HOT DURATION CAM
580184 OR-84 MAXIMUM COMP. 41-79 79-41 .448 .020 300o A
580144 E-4 TORQUER 19-57 57-19 .425 .018 256° A
580166 AN-66 COMBINATION 23-61 61-23 .448 .018 264° A
580100 RPM COMPETITION 30-68 68-30 .426 .018 278° A
580111 SUPER RPM COMPETITION 47-85 85-47 .429 .030 312° A
580188 AN-88 SUPER COMPETITION 41-79 79-41 .507 .028 300° A
580133 *PT-3 For ‘67 & Up 1600 engs. 18-62 62-18 .455 .024 260° A
ASSEMBLY KIT COMPONENTS
AN-003 8 CHROME MOLY TUBULAR PUSHRODS, 105E, 109EAN-013 8 CHROME MOLY TUBULAR PUSHRODS (116E)*453 8 CHROME MOLY TUBULAR PUSHRODS (1600) PINTO & CORTINAVWE-005 8 SILICON CHROME OUTER VALVE SPRINGSSP-006 8 SILICON CHROME INNER VALVE SPRINGS (STREET & COMPETITION)SP-116 8 SILICON CHROME INNER VALVE SPRINGS (SUPER COMPETITION)AN-007 8 ALUMINUM VALVE SPRING RETAINERS
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.182
183
JAGUAR • D.O.H.C. 6 Cylinder
RACING CAMS*NOTE: We also grind the V-12 Jaguar camshafts to XM-2 and XM-3 specs.: $480.00 list.
CAMS NOT AVAILABLE OUTRIGHT.
MGA & MGB • MAGNETTE SEDAN • BMC “B” TYPE •
*NOTE: CAMS NOT AVAILABLE OUTRIGHT.
ASSEMBLY KIT COMPONENTS
JA-005 12 SILICON CHROME OUTER VALVE SPRINGSJA-006 12 SILICON CHROME INNER VALVE SPRINGSJA-008 12 THICKENED, HARDENED ADJUSTING DISCS (.177” THICK)
VALVE GRIND GRIND VALVE LASH ADVERTISED .050 CUSTOMERS NO. TYPE INTAKE EXHAUST LIFT COLD DURATION DURATION CAM
X-5 TORQUER 17-57 57-17 E
*XM-2 COMBINATION 19-59 59-19 E
*XM-3 MAXIMUM COMPETITION 24-64 64-24 E
*Z-199 COMPETITION 19-59 59-19 E
*XM-5 ULTRA-SUPER COMP. 29-69 69-29 E
.390 .012 254° 230° .390 .014 254° 230°
.404 .012 258° 232° .404 .014 258° 232°
.424 .012 268° 242° .424 .014 268° 242°
.444 .012 258° 236° .444 .014 258° 236°
.440 .012 278° 254° .440 .014 278° 254°
*These profiles are ground on modified cores only. Prices shown are for (1) Pair of Cams.(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.)
ASSEMBLY KIT COMPONENTS
*MG-05 8 SILICON CHROME OUTER VALVE SPRINGS 927-ST(8) 8 CHROME MOLY STEEL RETAINERS*MG-06 8 SILICON CHROME INNER VALVE SPRINGS MG-003 8 CHROME MOLY TUBULAR PUSHRODS (STOCK LIFTER)3607-ST 8 CHROME MOLY STEEL RETAINERS (MGB-1800cc ENGINES) MG-013 8 CHROME MOLY TUBULAR PUSHRODS (Sprite or *#1258 Holesaw required on some MGB engines with small dia. spring seats Morris Lifter
(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.)
VALVE GRINDGRIND LASH .050 CUSTOMERS NO. TYPE INTAKE EXHAUST LIFT HOT DURATION DURATION CAM Z-99 STOCK REFINISHING 16-50 50-16 A
Z-50E4 MILD PERFORMANCE 19-53 53-19 A
T-32 STREET / AUTOCROSS 23-57 59-25 B
T-55 COMPETITION 25-59 59-25 A
T-55+10 COMPETITION 30-64 64-30 A
T-66 MAXIMUM COMP. 36-70 70-36 A
.410 .016 246° ---- .410 .016 246° ---- .420 .018 252° 210° .420 .018 252° 210° .435 .018 260° 222° .430 .019 264° 228° .430 .018 264° 228° .430 .019 264° 228° .430 .018 274° 238° .430 .019 274° 238° .430 .020 286° 250° .430 .020 286° 250°
1500, 1600, 1622 &1800 cc engines
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
184
OPEL • 4 CYL. SOHC *1900 ENGINE (SEE NOTE BELOW)
OUTRIGHT SOLID CAM SOLID HYD. LIFTER VALVE GRIND LIFTER CAM GRIND VALVE LASH ADVERTISED .050 CUSTOMERS CAM. PART NO. NO. TYPE INTAKE EXHAUST LIFT HOT DURATION DURATION CAM
625144 625140 OR-4 TORQUER 18-58 58-18 .407 .018 256° B
625166 625160 OR-66 COMBINATION 24-64 64-24 .430 .018 268° 228° B
625177 ---- OR-77 MAX. COMP. 32-72 72-32 .430 .020 284° 248° B
625199 ---- OR-99 ULT.-SUP. COMP 40-80 80-40 .480 .028 300° 252° B
TOYOTA COROLLA • 1600 cc - 4 Cylinder - Pushrod-Hemi Engine (2-TC)
*NOTE: 1971 & later Opel engines come equipped with hydraulic lifters from the factory, and should remain hydraulic. Solid lifter cams should beused in Pre 71’ engines that came equiped with factory solid lifters.(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.)
ASSEMBLY KIT COMPONENTS455/626 8 SILICON CHROME DUAL VALVE SPRINGS STMR 8 STEEL VALVE SPRING RETAINERS
(ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.)
OUTRIGHT VALVE GRIND PART GRIND VALVE LASH ADVERTISED .050 CUSTOMERS NO. NO. TYPE INTAKE EXHAUST LIFT HOT DURATION DURATION CAM
678155 TH-55 COMBINATION 19-61 61-19 .430 .024 260° 222° A
678177 TH-77 COMPETITION 29-71 71-29 .460 .018 280° 240° A
678150 LL 505-T COMPETITION 34-76 76-34 .490 .028 290° 242° A
678199 TH-99 COMPETITION 39-81 81-39 .480 .028 300° 254° A
678135 Z-35 COMPETITION 34-74 74-34 .508 .018 288° 254° A
678190 TH-99 + 10 COMPETITION 44-86 86-44 .480 .028 310° 264° A
678160 Z-60 MAX. COMPETITION 36-76 76-36 .529 .018 292° 259° A
TOYOTA-20R-22R • 4 Cylnder SOHC Engines
VALVE GRIND OUTRIGHT VALVE LASH ADVERTISED .050 CUSTOMERS PART NO. GRIND NO. TYPE LIFT COLD DURATION DURATION CAM 690144 440 MILD GRIND FOR .440 .008 280° 230° B TURBOCHARGER 690146 465 BEST ALL-AROUND .465 .010 300° 240° B PERFORMANCE 690155 505B MAXIMUM .505 .010 310° 255° B COMPETITION
VALVE SPRINGS 626 8 SILICON CHROME INNER VALVE SPRINGS (USE WITH STOCK OUTER SPRING)
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
185
TRIUMPH • 6 Cylinder OHV Engines TR-6, GT-6
RACING CAMS*NOTE: CAMS NOT AVAILABLE OUTRIGHT.
VALVE GRIND GRIND VALVE LASH ADVERTISED CUSTOMERS NO. TYPE INTAKE EXHAUST LIFT HOT DURATION CAM
Z-19 ROAD & RACE 24-64 64-25 .400 .016 268° B
Z-66+10 COMPETITION 31-71 71-31 .425 .018 282° B
VOLVO • 4 Cylinder B-16 or B-18/20 Model Engines
B-16 ASSEMBLY KIT*625 8 OUTER VALVE SPRINGS IVS-5/16 8 ISKY VALVE STEM OIL SEALS*626 8 INNER VALVE SPRINGS *VST-5/16 1 INSTALLATION CUTTER FOR SEALS327-ST 8 CHROME MOLY STEEL RETAINERS *208-M 1 HOLESAW REQUIRED FOR SPRING INSTALLATION
B-18 ASSEMBLY KIT*625 8 OUTER VALVE SPRINGS IVS-11/32 8 ISKY VALVE STEM OIL SEALS*626 8 INNER VALVE SPRINGS *VST-11/32 1 INSTALLATION CUTTER FOR VALVE SEALSPO-17 8 ALUMINUM SPRING RETAINERS *208-M 1 HOLESAW REQUIRED FOR SPRING INSTALLATION202-H 8 HARDENABLE IRON LIFTERSVL-123 8 CHROME MOLY PUSHRODS (FOR 202-H LIFTER)
B-20 ASSEMBLY KIT*625 8 OUTER VALVE SPRINGS IVS-5/16 8 ISKY VALVE STEM OIL SEALS*626 8 INNER VALVE SPRINGS *VST-5/16 1 INSTALLATION CUTTER FOR VALVE SEALS327-ST 8 CHROME MOLY STEEL RETAINERS *208-M 1 HOLESAW REQUIRED FOR SPRING INSTALLATION202-H 8 HARDENABLE IRON LIFTERS VL-013 8 PUSHRODS - B-18-20 ENGINE - STOCK LIFTERVL-123 8 CHROME MOLY PUSHROD (FOR 202-H LIFTER)
OUTRIGHT VALVE GRIND B-16 B-18/20 GRIND VALVE LASH ADVERTISED CUSTOMERSPART NO. PART NO. NO. TYPE INTAKE EXHAUST LIFT HOT DURATION CAM
705161 700161 VV-61 STOCK REPL. TORQUER 20-56 56-20 .425 .020 256° A
705171 700171 VV-71 COMBINATION 26-62 62-26 .428 .020 268° A
705181 700181 VV-81 COMPETITION 35-71 71-35 .428 .020 286° A
700132 Z-322 COMPETITION 32-68 68-32 .480 .018 280° A
705191 700191 VV-91 MAX. COMPETITION 42-78 78-42 .480 .028 300° A
700139 Z-349 MAX. COMPETITION 42-78 78-42 .510 300° A
705110 700110 VV-101 MAX. COMPETITION 44-86 86-44 .480 .028 310° A
705111 700111 VV-111 SUPER COMPETITION 49-91 91-49 .480 .028 320° A
700130 Z-309 SUPER COMPETITION 49-85 85-49 .538 .028 314° A
.014 .016
*NOTE: ONE CAN OF ISKY REV LUBE INCLUDED FREE WITH CAMS.
All Camshafts on this page are not legal for sale or use on pollution controlled motor vehicles operated on highways or roads.
ED ISKENDERIAN RACING CAMS16020 S. BROADWAY GARDENA, CALIFORNIA 90247-9990
(310) 217-9232 FAX (310) 515-5730www.iskycams.com US $5.00
top related