deep sea electronics plc - hipower systems: your … · deep sea electronics plc 702 automatic...
Post on 24-Apr-2018
234 Views
Preview:
TRANSCRIPT
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 1 -
DEEP SEA ELECTRONICS PLC
702 AUTOMATIC START MODULE
OPERATING INSTRUCTIONS
Author:- Anthony Manton
Deep Sea Electronics Plc Highfield House
Hunmanby North Yorkshire
YO14 0PH England
Tel: +44 (0) 1723 890099 Fax: +44 (0) 1723 893303
email: Sales@Deepseaplc.com
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 2 -
<< This page is intentionally blank >>
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 3 -
TABLE OF CONTENTS
1 DESCRIPTION OF OPERATION .......................................................... 4 1.1 MANUAL MODE OPERATION ......................................................................... 4 1.2 AUTOMATIC MODE OF OPERATION ............................................................. 5 1.3 WARNINGS ....................................................................................................... 6 1.4 SHUTDOWNS ................................................................................................... 6
2 SETTINGS ............................................................................................. 7 2.1 FIXED SETTINGS ............................................................................................. 7 2.2 CONFIGURABLE SETTINGS ........................................................................... 7
3 TERMINAL DESCRIPTION ................................................................... 7
4 SPECIFICATION ................................................................................... 8
5 SOLID STATE OUTPUTS ..................................................................... 9 5.1 TYPICAL CONNECTIONS ................................................................................ 9
6 DIMENSIONS ...................................................................................... 10
7 TYPICAL CONNECTIONS .................................................................. 10
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 4 -
1 DESCRIPTION OF OPERATION 1.1 MANUAL MODE OPERATION
To initiate a start sequence in MANUAL, turn the key to the position. To start the set, press the
button. Preheating will begin, indicated by the LED.
NOTE:- There is no Start Delay in this mode of operation. Starting will commence as
soon as the start button is pressed.
The Fuel Solenoid is energised, then the Starter Motor is engaged. The engine is cranked for a 10-second period. If the engine fails to fire during this cranking attempt then the starter motor is disengaged for a 10-second period. Should this sequence continue
beyond the 3 starting attempts, the start sequence will be terminated and Fail to Start fault will be illuminated. When the engine fires, the starter motor is disengaged and locked out at 20 Hz measured from the Alternator output. After the starter motor has disengaged, the Safety On timer is activated (which is fixed at 10 seconds), allowing Oil Pressure, High Engine Temperature, Under-speed and Charge Fail to stabilise without triggering the fault.
Selecting STOP de-energises the FUEL SOLENOID, bringing the generator to a stop.
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 5 -
1.2 AUTOMATIC MODE OF OPERATION
To initiate a start sequence in AUTO, turn the key to the position. The start sequence is initiated when the remote start input is activated.
After a fixed 5 second start delay, Preheating will occur (fixed at 10s) , indicated by the LED. the Fuel Solenoid is energised, then one second later, the Starter Motor is engaged. The engine is cranked for a 10-second period. If the engine fails to fire during this cranking attempt then the starter motor is disengaged for a 10-second rest period. Should this sequence continue beyond the 3 starting attempts, the start sequence will be terminated and
Fail to Start fault will be illuminated. When the engine fires, the starter motor is disengaged and locked out at 20 Hz measured from the Alternator output.. After the starter motor has disengaged, the Safety On timer is activated, allowing Oil Pressure, High Engine Temperature, Under-speed and Charge Fail to stabilise without triggering the fault. On removal of the Remote Start signal the Stop delay timer is initiated. Once this timer has expired the Fuel Solenoid is de-energised, bringing the generator to a stop.
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 6 -
1.3 WARNINGS Warnings are used to warn the operator of an impending fault BATTERY CHARGE FAILURE, if the module does not detect a voltage from the warning light
terminal on the auxiliary charge alternator, the icon will illuminate.
1.4 SHUTDOWNS Shutdowns are latching and stop the Generator. The alarm must be cleared, and the fault removed to reset the module. In the event of a shutdown the appropriate LED will be illuminated
NOTE:- The alarm condition must be rectified before a reset will take place. If the alarm condition remains it will not be possible to reset the unit (The exception to this is the Low Oil Pressure alarm and similar ‘delayed alarms’, as the oil pressure will be low with
the engine at rest).
FAIL TO START, if the engine does not fire after the pre-set 3 attempts at starting, a shutdown will be initiated.
The icon will illuminate. LOW OIL PRESSURE, if the module detects that the engine oil pressure has fallen below the low oil pressure switch after the Safety On timer has expired, a shutdown will occur.
The icon will illuminate. HIGH ENGINE TEMPERATURE if the module detects that the engine coolant temperature has exceeded the high engine temperature switch after the Safety On timer has expired, a shutdown will occur.
The icon will illuminate. OVERSPEED, if the engine speed exceeds the pre-set trip (14% above the nominal frequency) a shutdown is initiated. Overspeed is not delayed, it is an immediate shutdown.
The icon will illuminate.
NOTE:- During the start-up sequence the overspeed trip level is extended to 24% above the normal frequency for the duration of the safety timer to allow an extra trip level margin. This is used to prevent nuisance tripping on start-up.
UNDERSPEED, if the engine speed falls below 20Hz (fixed) after the Safety On timer has expired, a shutdown is initiated.
The icon will flash.
NOTE:- The icon is used to indicate both underspeed and overspeed. A flashing
icon indicates underspeed. A steady icon indicates overspeed.
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 7 -
2 SETTINGS
2.1 FIXED SETTINGS The following settings are factory set and are NOT adjustable.
Crank disconnect 20Hz
Underspeed 20Hz
Overspeed 57Hz (50Hz nominal) 68 Hz (60Hz nominal)
Remote start delay 5s
Preheat 10s
Crank period 10s
Crank rest 10s
Safety delay 10s
Remote stop delay 30s
2.2 CONFIGURABLE SETTINGS The following setting is factory set to 50Hz but is user adjustable.
To select between 50/60Hz nominal frequency, operate the selector switch into the correct position as shown opposite.
50Hz 60Hz
3 TERMINAL DESCRIPTION
PIN No
DESCRIPTION CABLE SIZE
NOTES
1 DC Plant Supply Input (-ve)
1.0mm Connected to plant battery negative
2 DC Plant Supply Input (+ve)
1.0mm Connected to plant battery positive (Recommended Fuse 2A)
3 Fuel relay Output 0.5mm Used to operate the fuel solenoid control relay.
4 Start relay Output 0.5mm Used to operate the cranking control relay.
5 Preheat Output relay 0.5mm Used to operate the preheat control relay.
6 Remote Start Input 0.5mm Switch to negative to start set.
7 Charge Fail Input/ Excitation Output
1.0mm Must NOT be connected to plant supply negative if not used.
8 Low Oil Pressure Input 0.5mm Switch to negative on fault.
9 High Engine Temp Input 0.5mm Switch to negative on fault.
10 Alternator Input L1 1.0mm 2A Fuse
11 Alternator Input N 1.0mm
NOTE:- All the outputs are solid state, rated at 1.2 Amps 8 Volts to 35 Volts DC, and switch to battery negative when active.
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 8 -
4 SPECIFICATION
DC Supply: 8 Volts to 35 Volts DC Continuous. Cranking Dropouts: Able to survive 0 Volts for 50 mS, providing supply was at
least 10 V before dropout and supply recovers to 5 Volts. This is achieved without the need for internal batteries.
Max. Current: Operating 50mA Standby 10mA
Alternator Input Range: 15 Volts (ph-N) to 277 Volts (ph-N) AC (+20%) Alternator Input Frequency: 50 - 60 Hz at rated engine speed
(Minimum: 75V AC Ph-N) (Crank Disconnect from 15V Ph-N @ 20Hz) Overspeed +14% (+24% overshoot)
Start Output: 1.2 Amp DC at supply voltage. Fuel Output: 1.2 Amp DC at supply voltage.
Preheat Output: 1.2 Amp DC at supply voltage. Dimensions: 84mm x 72mm x 34.9mm
(3.3” x 2.8” x 1.4”) Operating Temperature Range: -30 C to + 70
0C
Applicable Standards
Compliant with BS EN 60950 Low Voltage Directive Compliant with BS EN 50081-2: 1992 EMC Directive Compliant with BS EN 61000-6-4: 2000 EMC Directive
Compliance to European Legislation
Registered Component for USA & Canada
Deep Sea Electronics plc reserve the right to change specification without notice.
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 9 -
5 SOLID STATE OUTPUTS DSE’s utilisation of Solid State Outputs gives many advantages, the main points being:
No Moving Parts
Fully Overload / Short Circuit Protected.
Smaller dimensions hence lighter, thinner and cheaper than conventional relays.
Less power required making them far more reliable. The main difference from conventional outputs is that solid state outputs switch to negative (–ve) when active. This type of output is normally used with an automotive or plug in relay.
5.1 TYPICAL CONNECTIONS
Battery positive (+)
Solid state output from DSE module
eg. Terminal 3 of 702 - FUELFuel Solenoid (+ terminal)
* Observe polarity when using
relays fitted with integraldiodes!
*
A D
B C
A B C D
Solid State Output from DSE Module Pin
Automotive relay Pin
8 Pin Plugin relay Function
3 86 7 Fuel Output 85 2 To Positive supply via fuse 30 1 To Positive supply via fuse 87 3 To Fuel Solenoid
Example of relay pins connected to DSE solid state output to drive a fuel solenoid.
See section on Typical Connections else where in this manual for overall typical wiring diagram
702 Operating Instructions Issue 1 04/07/2007 17:26:00 ADM - 10 -
6 DIMENSIONS
Imperial measurements Overall dimensions (excluding key) 3.3” x 2.8” x 1.4” (protrudes 0.16” out of panel)
7 TYPICAL CONNECTIONS
F 2A
To fused Plant Supply +ve
SSOSSOSSO
SSO = Solid state outputs
= External 'Automotive' or 'Plug-in' type relays
31 2 4 57 8 9 6
1011
++
+
F 2A
F
Rem
ote
sta
rt s
witch
Engin
e t
em
p s
witch
Low
oil p
ressure
sw
itch
Battery negative should be grounded
Startermotor
Crank Fuel
BatteryCharge
alt.
L1
N
Alternator
Pre-heat output
Terminals suitable for 22-16 awg (0.6mm2-1.3mm
2 )field wiring
Tightening Torque = 0.8N-m (7lb-in)
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 1 -
DEEP SEA ELECTRONICS PLC
701 KEY START MODULE
OPERATING INSTRUCTIONS
Author:- John Ruddock
Deep Sea Electronics Plc Highfield House
Hunmanby North Yorkshire
YO14 0PH England
Tel: +44 (0) 1723 890099 Fax: +44 (0) 1723 893303
email: Sales@Deepseaplc.com
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 2 -
<< This page is intentionally blank >>
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 3 -
TABLE OF CONTENTS
1 DESCRIPTION OF OPERATION .......................................................... 4 1.1 WARNINGS ....................................................................................................... 5 1.2 SHUTDOWNS ................................................................................................... 5
2 CONFIGURATION INSTRUCTIONS ..................................................... 6
3 TERMINAL DESCRIPTION ................................................................... 7
4 SPECIFICATION ................................................................................... 8
5 SOLID STATE OUTPUTS ..................................................................... 9
6 DIMENSIONS ...................................................................................... 10
7 TYPICAL CONNECTIONS .................................................................. 10
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 4 -
1 DESCRIPTION OF OPERATION
To start the generator turn the key switch to the hand position, which will power up the unit.
If at this time the auxiliary input is active the led will be illuminated, preventing the start of the generator.
Pressing the pre-heat button will energise the pre-heat output. Releasing the button will de-energise the output.
Pressing the start button will energise the Fuel Solenoid output, then the Starter Motor output. The button should be pressed for the duration of the crank period. When the engine fires, the starter motor is disengaged and locked out at 20 Hz measured from the Alternator output. After the starter motor has disengaged, the Safety On timer is activated (which is fixed at 12 seconds), allowing Oil Pressure, High Engine Temperature and Charge Fail to stabilise without triggering the fault.
Turning the key to STOP de-energises the FUEL SOLENOID, bringing the generator to a stop.
NOTE: - The safety on time (used for delayed alarms) is pre set to 12 seconds and can
not be changed.
NOTE: - If the generator has not started when the start button has been released
or the generator fails once it is running, the key switch must be turned to STOP and
then back to before another start can be invoked.
NOTE: - If pre-heat is required during cranking, the pre-heat button should be
pressed at the same time as the start button.
NOTE: - The 701HC start button is represented by
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 5 -
1.1 WARNINGS Warnings are used to warn the operator of an impending fault BATTERY CHARGE FAILURE, if the module does not detect a voltage from the warning light
terminal on the auxiliary charge alternator, the icon will illuminate.
1.2 SHUTDOWNS Shutdowns are latching and stop the Generator. The alarm must be cleared, and the fault removed to reset the module. In the event of a shutdown the appropriate icon will be illuminated
Auxiliary Input, if the auxiliary input is energised an immediate shutdown will occur. The icon will illuminate.
NOTE: - If the Auxiliary input is used to shutdown the engine, the fault must be cleared before the unit can be reset and the generator restarted.
LOW OIL PRESSURE, if the module detects that the engine oil pressure has fallen below the low oil pressure switch setting, after the Safety On timer has expired, a shutdown will occur.
The icon will illuminate. HIGH ENGINE TEMPERATURE if the module detects that the engine coolant temperature has exceeded the high engine temperature switch setting, after the Safety On timer has expired, a shutdown will occur.
The icon will illuminate. OVERSPEED, if the engine speed exceeds the pre-set trip (14% above the nominal frequency) a shutdown is initiated. Overspeed is not delayed, it is an immediate shutdown.
The icon will illuminate.
NOTE: - During the start-up sequence the overspeed trip level is extended to 24% above the normal frequency for the duration of the safety timer to allow an extra trip level
margin. This is used to prevent nuisance tripping on start-up.
NOTE: - The safety on time (used for delayed alarms) is pre set to 12 seconds and can not be changed.
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 6 -
2 CONFIGURATION INSTRUCTIONS
The only parameter to be configured is the nominal frequency, either 50 Hz or 60 Hz. The change is made via a switch which is accessible through a slot in the base of the module, (see photo)
60Hz 50Hz
This switch adjusts the over speed trip form 57 Hz to 68 Hz, and over shoot from 62 Hz to 70
Hz.
Model 701 Model 701 HC
60Hz-50Hz Switch
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 7 -
3 TERMINAL DESCRIPTION
PIN No
DESCRIPTION CABLE SIZE
NOTES
1 DC Plant Supply Input (-ve)
1.0mm Connected to plant battery negative
2 DC Plant Supply Input (+ve)
1.0mm Connected to plant battery positive (Recommended Fuse 2A)
3 Fuel relay Output 1.0mm Used to operate the fuel relay.
4 Start relay Output 1.0mm Used to operate the cranking relay.
5 Pre-Heat Output 1.0mm Used to operate the pre heaters. E.g. glow plugs
6 Auxiliary Input Shutdown 1.0mm Switch to negative.
7 Charge Fail Input/ Excitation Output
1.0mm Must NOT be connected to plant supply negative if not used.
8 Low Oil Pressure Input 0.5mm Switch to negative.
9 High Engine Temp Input 0.5mm Switch to negative.
10 Alternator Input N 1.0mm Connect to Generator Neutral (AC).
11 Alternator Input L1 1.0mm Connect to Generator L1 supply (AC) (Recommend 2A Fuse Max.)
NOTE:- All the outputs are solid state, rated at 1.2 Amps 8 Volts to 35 Volts DC, and
switch to battery negative when active.
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 8 -
4 SPECIFICATION
DC Supply: 8 Volts to 35 Volts DC Continuous. Cranking Dropouts: Able to survive 0 Volts for 50 mS, providing supply was at
least 10 V before dropout and supply recovers to 5 Volts. This is achieved without the need for internal batteries.
Max. Current: Operating 9mA In Off Mode 0mA
Hours Counter (701 HC only) 0 – 99,999.9 Hours. Tamper Proof Alternator Input Range: 15 Volts (ph-N) to 305 Volts (ph-N) AC (+20%)
Alternator Input Frequency: 50 - 60 Hz at rated engine speed (Minimum: 75V AC Ph-N) (Crank Disconnect from 15V Ph-N @ 20Hz) Overspeed +14% (+24% overshoot)
Start Output: 1.2 Amp DC at supply voltage. Fuel Output: 1.2 Amp DC at supply voltage.
Pre Heat: 1.2 Amp DC at supply voltage. Charge Fail: 3 Volts
Operating Temperature Range: -30 C to + 700C
Applicable Standards
Compliant with BS EN 60950 Low Voltage Directive Compliant with BS EN 50081-2: 1992 EMC Directive Compliant with BS EN 61000-6-4: 2000 EMC Directive
Compliance to European Legislation
Registered Component for USA & Canada
Deep Sea Electronics plc reserve the right to change specification without notice.
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 9 -
5 SOLID STATE OUTPUTS DSE’s utilisation of Solid State Outputs gives many advantages, the main points being:
No Moving Parts
Fully Overload / Short Circuit Protected.
Smaller dimensions hence lighter, thinner and cheaper than conventional relays.
Less power required making them far more reliable. The main difference from conventional outputs is that solid state outputs switch to negative (–ve) when active. This type of output is normally used with an automotive or plug in relay.
TYPICAL CONNECTIONS
Battery positive (+)
Solid state output from DSE module
eg. Terminal 3 of 701 - FUEL
Fuel Solenoid (+ terminal)
* Observe polarity when usingrelays fitted with integral diodes!
*
A D
B C
A B C D
Solid State Output from DSE Module Pin
Automotive relay Pin
8 Pin Plugin relay Function
3 86 7 Fuel Output 85 2 To Positive supply via fuse 30 1 To Positive supply via fuse 87 3 To Fuel Solenoid
Example of relay pins connected to DSE solid state output to drive a fuel solenoid.
See overleaf for overall typical wiring diagram
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 10 -
6 DIMENSIONS 701 701HC Dimensions: Excluding Key 72mm x 72mm x 38mm (2.83” x 2.83” x 1.32”) Panel cutout: 68mm x 68mm (2.68” x 2.68”) Mounting Method: 2 x Fixing Clips (Supplied).
Dimensions: Excluding Key 84mm x 72mm x 34.9mm (3.3” x 2.8” x 1.4”) Panel cutout: 80mm x 68mm (3.14” x 2.67”) Mounting Method: 2 x Fixing Clips (Supplied).
7 TYPICAL CONNECTIONS
F 2A
To fused Plant Supply +ve
SSOSSOSSO
SSO = Solid state outputs
= External 'Automotive' or 'Plug-in' type relays
31 2 4 57 8 9 6
1110
++
+
F 2A
F
Aux
shutd
ow
n
Engin
e tem
p s
witc
h
Low
oil
pre
ssure
sw
itch
Battery negative should be grounded
Startermotor
Crank Fuel
BatteryCharge
alt.
L1
N
Alternator
Pre-heat output
Terminals suitable for 22-16 awg (0.6mm2-1.3mm
2 )field wiring
Tightening Torque = 0.8N-m (7lb-in)
701 Operating Instructions Issue Issue 1 04/07/2007 17:27:00 JR - 11 -
<< This page is intentionally blank >>
top related