contaminationsensor cs 1939 - hydac danger – the signal word indicates a hazardous situation with...
Post on 29-Apr-2018
218 Views
Preview:
TRANSCRIPT
ContaminationSensor CS 1939
Operating and Maintenance Instructions English (translation of original instructions) Valid from: - Firmware version V 1.00 - Hardware index A - Serial number: 0002S01515K0001305 Keep for future reference.
Document No.: 3978342a
Imprint
Imprint
Manufacturer / publisher and responsible for the content: HYDAC FILTER SYSTEMS GMBH Postfach 1251 66273 Sulzbach / Saar Germany Telephone: +49 6897 509 01 Fax: +49 6897 509 9046 E-mail: filtersystems@hydac.com Homepage: www.hydac.com Court of Registration: Saarbrücken, HRB 17216 Executive director: Mathias Dieter,
Dipl.Kfm. Wolfgang Haering
Documentation Representative
Mr. Günter Harge c/o HYDAC International GmbH, Industriegebiet, 66280 Sulzbach / Saar Telephone: +49 6897 509 1511 Fax: +49 6897 509 1394 E-mail: guenter.harge@hydac.com
© HYDAC FILTER SYSTEMS GMBH
All rights reserved. No part of this work may be reproduced in any form (print, photocopy or by other means) or processed, duplicated or distributed using electronic systems without the written consent of the publisher. These documents have been created and inspected with the greatest care. However, errors cannot be ruled out completely. All details are subject to technical modifications. Technical specifications are subject to change without notice.
ContaminationSensor CS 1939 en(us) Page 2 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Content
Content
Imprint ............................................................................................................ 2
Documentation Representative ................................................................... 2
Content .......................................................................................................... 3
Preface ........................................................................................................... 5
Technical Support ........................................................................................ 5 Modifications to the Product ........................................................................ 5 Warranty ...................................................................................................... 5 Using the documentation ............................................................................. 6
Safety Information ........................................................................................ 7
Hazard symbols ........................................................................................... 7 Signal words and their meaning in the safety information and instructions .................................................................................................. 8 Structure of the safety information and instructions ..................................... 8 Observe regulatory information ................................................................... 9 Proper/Designated Use ............................................................................... 9 Improper Use or Use Deviating from Intended Use ................................... 10 Qualifications of personnel / target group .................................................. 11
Storing product ........................................................................................... 13
Storage conditions ..................................................................................... 13
Decoding the type label .............................................................................. 13
Checking the scope of delivery ................................................................. 14
ContaminationSensor CS 1939 features ................................................... 15
Dimensions ................................................................................................ 15 Hydraulic connection types ........................................................................ 16
Pipe or hose connection ......................................................................... 16 Flange connection .................................................................................. 17
Installing ContaminationSensor ................................................................ 18
Fastening/mounting the ContaminationSensor .......................................... 18 ContaminationSensor hydraulic installation ............................................... 20
Selecting the measurement location ...................................................... 21
Flow rate, differential pressure p∆ and viscosity ν characteristics ........................................................................................ 22
Hydraulic connection of the ContaminationSensor .................................... 23 Electrical connection of the ContaminationSensor .................................... 24
Pin assignment ....................................................................................... 24 Connection cable - Assignment / Color coding ....................................... 25
Status signals / status LED / troubleshooting .......................................... 26
ContaminationSensor CS 1939 en(us) Page 3 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Content
Applying SAE J1939 protocol .................................................................... 27
Parameter definition .................................................................................. 27 SPN definition......................................................................................... 27
Evaluating/reading measurement reports with FluMoS or FluMoT ........ 28
Performing maintenance ............................................................................ 29
Cleaning the ContaminationSensor ........................................................... 29 Resetting ................................................................................................... 29
Decommissioning the product .................................................................. 29
Disposing of the product ........................................................................... 29
Spare Parts and Accessories .................................................................... 30
Checking/resetting default settings .......................................................... 31
Dialog menu .............................................................................................. 31
Calibrating ContaminationSensor ............................................................. 31
Technical Data............................................................................................. 31
Annex ........................................................................................................... 33
Model code ................................................................................................ 33 Finding Customer Service ......................................................................... 34
Germany ................................................................................................ 34 USA ........................................................................................................ 34 Australia ................................................................................................. 34 Brazil ...................................................................................................... 35 China ...................................................................................................... 35
Cleanliness classes - brief overview .......................................................... 36 Cleanliness class - ISO 4406:1999 ........................................................ 36 Table - ISO 4406 .................................................................................... 36 Overview of modifications - ISO4406:1987 <-> ISO4406:1999 .............. 37
Explanation of terms and abbreviations ..................................................... 38 Index .......................................................................................................... 40
ContaminationSensor CS 1939 en(us) Page 4 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Preface
Preface
These operating instructions were made to the best of our knowledge. Nevertheless and despite the greatest care, it cannot be excluded that errors could have crept in. Therefore please understand that, in the absence of any provisions to the contrary hereinafter, our warranty and liability – for any legal reasons whatsoever – are excluded in respect of the information in these operating instructions. In particular, we shall not be liable for lost profit or other financial loss. This exclusion of liability does not apply in cases of intent and gross negligence. Moreover, it does not apply to defects which have been deceitfully concealed or whose absence has been guaranteed, nor in cases of culpable harm to life, physical injury and damage to health. If we negligently breach any material contractual obligation, our liability shall be limited to foreseeable damage. Claims due to Product Liability shall remain unaffected.
Technical Support Contact our technical sales department if you have any questions on our product. When contacting us, please always include the model code, serial no. and part no. of the product: Fax: +49 6897 / 509 - 9046 E-mail: filtersystems@hydac.com
Modifications to the Product We would like to point out that changes to the product (e.g. purchasing additional options, etc.) may mean that the information in the operating instructions is no longer applicable or adequate. After modification or repair work that affects the safety of the product has been carried out on components, the product may not be returned to operation until it has been checked and released by a HYDAC technician. Please notify us immediately of any modifications made to the product whether by you or a third party.
Warranty For the warranty provided by us, please refer to the terms of delivery of HYDAC FILTER SYSTEMS GMBH. You will find these under www.hydac.com -> Legal information.
ContaminationSensor CS 1939 en(us) Page 5 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Preface
Using the documentation
Note that the method described for locating specific information does not release you from your responsibility of carefully reading these instructions prior to starting the unit up for the first time and at regular intervals in the future.
What do I want to know? I determine which topic I am looking for. Where can I find the information I’m looking for? The documentation has a table of contents at the beginning. There, I select the chapter I'm looking for and the corresponding page number.
deHYDAC Filtertechnik GmbHBeWa 123456a de
Seite x
Produkt / Kapitel
200x-xx-xx
The documentation number with its index enables you to order another copy of the operating and maintenance instructions. The index is incremented every time the manual is revised or changed.
Chapter heading
Page number Edition date
Document language Documentation no. with Index /
File name
ContaminationSensor CS 1939 en(us) Page 6 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Safety Information
The product was built according to the statutory provisions valid at the time of delivery and satisfies current safety requirements. Any residual hazards are indicated by safety information and instructions and are described in the operating instructions. Observe all safety and warning instructions attached to the product. They must always be complete and legible. Do not operate the product unless all the safety devices are present. Secure the hazardous areas which may arise between the product and other equipment. Maintain the product inspection intervals prescribed by law. Document the results in an inspection certificate and keep it until the next inspection.
Hazard symbols These symbols are listed for all safety information and instructions in these operating instructions which indicate particular hazards to persons, property or the environment. Observe these instructions and act with particular caution in such cases. Pass all safety information and instructions on to other users.
General hazard
Danger due to electrical voltage / current
Danger due to operating pressure
ContaminationSensor CS 1939 en(us) Page 7 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Signal words and their meaning in the safety information and instructions
The following signal words are to be found in these instructions.
DANGER DANGER – The signal word indicates a hazardous situation with a high level of risk, which, if not avoided, will result lethal or serious injury.
WARNING WARNING – The signal word indicates a hazardous situation with a medium level of risk, which, if not avoided, can result lethal or serious injury.
CAUTION CAUTION – The signal word indicates a hazardous situation with a low level of risk, which, if not avoided, can result in minor or moderate injury.
NOTICE NOTICE - The signal word indicates a hazardous situation with a high level of risk, which, if not avoided, will result in damage to property.
Structure of the safety information and instructions All warning instructions in this manual are highlighted with pictograms and signal words. The pictogram and the signal word indicate the severity of the danger. Warning instructions listed before an activity are laid out as follows:
HAZARD SYMBOL
SIGNAL WORD
Type and source of danger
Consequence of the danger
► Measures to avert danger
ContaminationSensor CS 1939 en(us) Page 8 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Observe regulatory information Observe the following regulatory information and guidelines:
• Legal and local regulations for accident prevention
• Legal and local regulations for environmental protection
• Country-specific regulations, organization-specific regulations
Proper/Designated Use Claims for defects or liability, regardless of the legal foundation, do not apply with incorrect or improper installation, commissioning, usage, handling, storage, maintenance, repair, use of unsuitable components or other circumstances for which HYDAC is not responsible. HYDAC is not responsible for the installation, integration, selection of interfaces to / into your system nor for the use or functionality of your system. Use the product only for the application described below. The ContaminationSensor CS 1939 serves to continuously monitor solid particulate contamination in hydraulic and lubrication systems. Proper/designated use of the product extends to the following:
• observing all instructions contained in the instruction manual.
• performing inspection and maintenance work. Depending on the version (see model code), you may use the CS only in connection with the following media:
NOTICE
Impermissible operating media
The ContaminationSensor will be destroyed.
► The ContaminationSensor may only be used in connection with mineral oils or mineral oil-based raffinates.
► Note the maximum operating pressure of 350 bar / 5075 psi.
ContaminationSensor CS 1939 en(us) Page 9 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Improper Use or Use Deviating from Intended Use
DANGER
Hazard due to use of the product other than that intended
Bodily injury and damage to property will result when operated improperly.
► Never operate the product in potentially explosive atmospheres.
► Only use the product with permissible media.
Any use extending beyond or deviating therefrom shall not be considered intended use. HYDAC FILTER SYSTEMS GMBH will assume no liability for any damage resulting from such use. The risk is borne solely by the owner. Improper use or use deviating from intended may result in hazards and/or will damage the sensor. Examples of improper use:
• Operation in potentially explosive atmospheres.
• Operation with a non-approved medium.
• Operation under non-approved operational conditions.
• Operation when the safety devices are defective.
• Modifications to the product made by the user or purchaser.
• Inadequate monitoring of parts that are subject to wear and tear.
• Improperly performed repair work.
ContaminationSensor CS 1939 en(us) Page 10 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Qualifications of personnel / target group Persons who work on the product must be aware of the hazards associated with its use. Auxiliary and specialist personnel must have read and understood the operating instructions, in particular the safety information and instructions, and applicable regulations before beginning work. The operating instructions and applicable regulations are to kept so they are accessible for operating and specialist personnel. These operating instructions are intended for: Auxiliary personnel: such persons have been instructed about the product and informed about potential hazards that can result from improper use. Specialist personnel: such persons with corresponding specialist training and several years' work experience. They are able to assess and perform the work assigned to them, they are also able to recognize potential hazards.
ContaminationSensor CS 1939 en(us) Page 11 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Safety Information
Activity Person Knowledge
Transport / storage Auxiliary personnel
• No specialist knowledge required
Hydraulic / electrical installation, First commissioning, Maintenance, Troubleshooting, Repair, Decommissioning, Disassembly
Specialist personnel
• Safe handling/use of tools
• Fitting and connection of hydraulic lines and connections
• Fitting and connection of electrical lines, electrical machinery, sockets, etc.
• Checking the phase sequence
• Product-specific knowledge
Operation Operations control
Specialist personnel
• Product-specific knowledge
• Knowledge about how to handle operating media.
Disposal Specialist personnel
• Proper and environmentally friendly disposal of materials and substances
• Decontamination of contaminants
• Knowledge about reuse
ContaminationSensor CS 1939 en(us) Page 12 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Storing product
Storing product
Store the product in a clean, dry place, in the original packaging if possible. Do not remove the packing until you are ready to install the unit. Rinse the ContaminationSensor completely with Cleanoil before putting it into storage. The solvents and flushing oils used must be handled and disposed of correctly.
Storage conditions Storage temperature: -40 … 80 °C / -40 … 176 °F Relative humidity: maximum 95%, non-condensing
Decoding the type label
For identification details of the ContaminationSensor, see the model code label. This is located on the back of the unit and contains the exact product description and the serial number.
Row -> Description
Model -> Model code; for details, see page 33.
P/N -> Part no.
S/N -> Serial-no.
Date -> Year/week of production and hardware index
Max. INLET press.: -> Maximum operating pressure
ContaminationSensor CS 1939 en(us) Page 13 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Checking the scope of delivery
Checking the scope of delivery
The ContaminationSensor CS 1939 comes packed and factory-assembled. Before commissioning the CS, please check no items are missing from the package. The following items are supplied: Qty Description
1 ContaminationSensor, CS 1939 (Model in acc. with the order - see model code)
2 O-rings (4.8 x 1.78 mm, 80 Shore, FKM) (only for the connection type "flange connection")
1 CD with operation and maintenance instructions (this document in various languages)
1 CD with FluMoS software (Fluid Monitoring Software)
1 Quick start manual
1 Calibration certificate
ContaminationSensor CS 1939 en(us) Page 14 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
ContaminationSensor CS 1939 features
ContaminationSensor CS 1939 features
The ContaminationSensor CS 1939 is a stationary measurement unit for the continuous monitoring of particulate contamination in hydraulic and lubrication systems. The ContaminationSensor is designed to be used in low- or high-pressure hydraulic and lubrication circuits and test benches where a small amount of oil (30–500 ml/min) is diverted for measurement purposes. The ContaminationSensor is approved for a maximum operating pressure (see specification on type label) and viscosity of up to 1000 mm²/s. The particulate contamination is recorded by an optical measurement cell.
Dimensions
All dimensions in mm.
ContaminationSensor CS 1939 en(us) Page 15 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
ContaminationSensor CS 1939 features
Hydraulic connection types If possible, install the CS so that fluid flows from bottom to top to avoid air collecting in the sensor. If it is not possible to install it like that, take other measures to ensure that air cannot collect in the sensor. Use port A / C as the INLET and B / D as the OUTLET.
Pipe or hose connection The hydraulic connection is done via ports A and B. Connection thread G1/4 according to ISO 228. Make sure that the flow runs through the sensor from bottom (A) to top (B).
ContaminationSensor CS 1939 en(us) Page 16 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
ContaminationSensor CS 1939 features
Flange connection The hydraulic connection is done via ports C and D. Two O-rings are used to form a seal between the CS and a flange, connecting plate or manifold mount. Four CS1000 threads are prepared for fixing the M6. Ports A and B are sealed off with screw plugs [1]. Sealing with the manifold block or mounting plate is done via two O-rings [2] (4.48 x 1.78 FPM, see Chapter "Spare Parts + Accessories").
View from below. All dimensions in mm.
ContaminationSensor CS 1939 en(us) Page 17 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Installing ContaminationSensor
In the following chapters you will find information on the assembly and the hydraulic and electrical installation of the ContaminationSensors.
Fastening/mounting the ContaminationSensor Install the ContaminationSensor in such a way that the flow runs from bottom to top. Use the one (lower) port as the INLET and the other (upper) port as the OUTLET. When selecting the installation site, take ambient factors like the temperature, dust, water, etc. into account. The ContaminationSensor is designed for IP67 according to DIN 40050 / EN 60529 / IEC 529 / VDE 0470. Mount the ContaminationSensor as shown in the following examples:
1. Wall mounting: Mount to a wall using two cylindrical screws having an M8 hexagonal socket according to ISO 4762 and having a length of at least 40 mm.
2. Console mounting:
Mount to a console using 4 cylindrical screws having an M6 hexagonal socket according to ISO 4762.
A B
10060
12/164xM6
1520
Bottom view All dimensions in mm.
ContaminationSensor CS 1939 en(us) Page 18 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
3. Installing on a mounting plate: Mount to a mounting plate or control block using 4 cylindrical screws having an M6 hexagonal socket according to ISO 4762.
ContaminationSensor CS 1939 en(us) Page 19 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
ContaminationSensor hydraulic installation If possible, install the ContaminationSensor so that fluid flows from bottom to top to avoid air collecting in the sensor. If it is not possible to install it like that, take other measures to ensure that air cannot collect in the sensor. Use port A / C as the INLET and B / D as the OUTLET. Depending on your order, the ContaminationSensor features the following hydraulic connection types: Pipe/hose connection: The ContaminationSensor is connected to the hydraulic system via ports A and B using a pipe or hose.
Flange connection: The ContaminationSensor is screwed to a flange, connecting plate, manifold mount or control block, with flow through the unit via ports C and D on the bottom. Ports A and B exist but are sealed with a screw plug.
Determine the operating pressure of the hydraulic system and see whether it is within the permissible flow range for the ContaminationSensor inlet.
NOTICE
Excessive operating pressure
The ContaminationSensor will be destroyed.
► Note the maximum operating pressure of 350 bar / 5075 psi.
ContaminationSensor CS 1939 en(us) Page 20 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Selecting the measurement location In order to obtain cleanliness values that are continuous and coherent in real time, select a suitable measuring point according to the following guidelines:
WRONG WRONG OK
1 Select the measurement point so that the sample measured comes from a turbulent location, with a good flow. For example: on a pipe elbow, etc.
2 Install the ContaminationSensor near the measurement point to achieve as timely results as possible.
3 During installation, avoid creating a "siphon" trap for particle deposits in the line (sedimentation).
ContaminationSensor CS 1939 en(us) Page 21 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Flow rate, differential pressure p∆ and viscosity ν characteristics
Differential pressure p∆ and viscosity ν characteristics. All the values indicated in the figures below apply regardless whether the direction of flow is A->B or B->A. Note that the permissible measured volumetric flow is 30 … 500 ml/min. If you are unable to achieve the required flow values, we offer an extensive line of accessories with various conditioning modules.
For example: You are using a fluid with a viscosity ν of 46 mm²/s at a pressure difference
p∆ of ≈0.9 bar, so that you achieve a flow rate of approx. 200 ml/min. The flow rate depends on the viscosity of the medium and the differential pressure p∆ via the sensor.
ContaminationSensor CS 1939 en(us) Page 22 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Hydraulic connection of the ContaminationSensor
NOTICE
Excessive operating pressure
The ContaminationSensor will be destroyed.
► Note the maximum operating pressure of 350 bar / 5075 psi.
Observe the following sequence when connecting the sensor to the hydraulic system:
1. Connect the return line to the OUTLET of the CS. G1/4 ISO 228 threaded connection, recommended diameter of line ≥ 4 mm.
2. Then connect the other end of the return line to the system tank, for example.
3. Check the pressure at the measurement location. Note the maximum operating pressure.
4. Connect the measurement line to the INLET port of the CS. Connector threads G1/4 ISO 228. We recommend an internal Ø ≤ 4mm for the line in order to prevent particle deposits (sedimentation).
If particles ≥ 400 µm are anticipated in the hydraulic systems, install a protective screen upstream from the ContaminationSensor. (e.g. CM-S)
5. Connect the other end of the measurement line to the measurement point on the hydraulic system.
Oil begins to flow as soon as the ContaminationSensor is connected with the pressure line.
6. The hydraulic connection is complete.
ContaminationSensor CS 1939 en(us) Page 23 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Electrical connection of the ContaminationSensor Pin assignment
Pin Assignment
1 Supply voltage 9-36 V DC
2 CAN H (SAE J1939)
3 GND power supply
4 CAN L (SAE J1939)
5 HSI (HYDAC Sensor Interface)
There is contact between the plug housing and the housing.
ContaminationSensor CS 1939 en(us) Page 24 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Installing ContaminationSensor
Connection cable - Assignment / Color coding Our accessories list on page 30 includes the required connection cables of various lengths with one connection plug (M12x1, 5-pole, according to DIN VDE 0627) and an open end. HYDAC accessory cable color coding is listed in the table below:
Pin Color Connection to
1 White Supply voltage 9-36 V DC
2 brown CAN H (SAE J1939)
3 Green GND power supply
4 Yellow CAN L (SAE J1939)
5 grey HSI (HYDAC Sensor Interface)
Housing - Shield
ContaminationSensor CS 1939 en(us) Page 25 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Status signals / status LED / troubleshooting
Status signals / status LED / troubleshooting
The status LED displays the following status signals. Error code
LED Description Remedy
0 Green No error Nothing required
3 Red Error during automatic adjustment
Perform a reset. If the error remains, rinse the CS against the direction of flow. Contact HYDAC Service if the error still occurs.
4 Red Error measuring cell LED
Reset the unit. Contact HYDAC Service if the error still occurs.
5 Red Flow too low Increase the flow rate through the CS.
6 Red Flow too high Reduce the flow rate through the CS.
7 Red Contamination too low
The sensor cannot detect a measured value. The operating fluid is apparently too clean.
8 Red Contamination too high
Reduce fluid contamination by filtration until the CS can measure the fluid purity.
16 Red Error while loading the user setup
Reset the unit. Contact HYDAC Service if the error still occurs.
17 Red Error while saving the user setup
Reset the unit. Contact HYDAC Service if the error still occurs.
18 Red Error while loading the calibration data
Reset the unit. Contact HYDAC Service if the error still occurs.
ContaminationSensor CS 1939 en(us) Page 26 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Applying SAE J1939 protocol
Applying SAE J1939 protocol
The CS 1939 has a CAN 2.0B port with access to the SAE J1939 log. Whenever the CS is switched on, it sends an "Address Claiming" message to share its name and address with the other participants. The measurement values are not transmitted cyclically but rather called up by the PGN 61184 on request.
Parameter definition PGN 61184
Acronym PC
Name CS 1939
Length 13
SPN definition
SP
N
Nam
e
Item
Leng
th
Type
Res
olut
ion
Offs
et
Min
. Val
ue
Max
. V
alue
Uni
t
516096 Status 1 8 BitField
516097 ISO 4 9 8 integer 0.1 0.0 8.0 25.0
516098 ISO 6 17 8 integer 0.1 0.0 7.0 24.0
516099 ISO 14 25 8 integer 0.1 0.0 6.0 23.0
516100 SAE A 33 8 integer 0.1 0.0 0.0 14.0
516101 SAE B 41 8 integer 0.1 0.0 0.0 14.0
516102 SAE C 49 8 integer 0.1 0.0 0.0 14.0
516103 SAE D 57 8 integer 0.1 0.0 0.0 14.0
516104 Temp 65 16 integer 0.1 -60.0 0.0 185.0 °C
516105 Flow 81 16 integer 0.1 0 30 500 ml/ min
516106 Drive 97 8 integer 0.1 0 0 100 %
ContaminationSensor CS 1939 en(us) Page 27 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Evaluating/reading measurement reports with FluMoS or FluMoT
Evaluating/reading measurement reports with FluMoS or FluMoT
The FluidMonitoring Software FluMoS is for reading and analyzing the measurement reports/measurement data. FluMoS light is available as freeware on the CD included in the delivery or as a download. You will find the link for the download on our homepage at www.hydac.com.
You can order FluMoS professional as a fee-based accessory. See chapter “Spare Parts and Accessories“, page 30.
The FluMoT FluidMonitoring Toolkit is comprised of a package of drivers and programs used for connecting the sensor to the customer's own software and solutions. See chapter “Spare Parts and Accessories“, page 30.
ContaminationSensor CS 1939 en(us) Page 28 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Performing maintenance
Performing maintenance
The ContaminationSensor is maintenance-free. Clean the CS regularly, as described in the "Cleaning the ContaminationSensor" chapter.
Cleaning the ContaminationSensor Clean the surface with a clean, damp cloth. Do not use any chemical cleaning agent as these may damage the film attached to the surface.
Resetting To restart or reset the ContaminationSensor, remove the power supply for 10 seconds.
Decommissioning the product
To decommission, proceed as follows: 1. Disconnect and remove the electric connection to the product. 2. Close any shut-off devices in the feed and return lines to the
product. 2. Depressurize the unit. 3. Remove the hydraulic connection lines to the product. 4. Remove the product.
Disposing of the product
Dispose of the packaging material in an environmentally friendly manner. After dismantling the product and separating its various materials, dispose of it in an environmentally friendly manner.
ContaminationSensor CS 1939 en(us) Page 29 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Spare Parts and Accessories
Spare Parts and Accessories
Description Qty. Part no.
Operating and Maintenance Instructions 1 3978342
O-ring for the flange connection (4.8x1.78 - 80 Shore FKM) 1 6003048
Socket plug (female) with 5 m line, shielded, 5-pole, M12x1
ZBE 47S-05 1 3527626
Extension cable 5 m, Socket plug (female) 5-pole, M12x1 / Socket plug (male) 5-pole, M12x1
ZBE 30-05
1 6040852
Socket plug with screw terminals, 5-pole, M12x1
1 6049128
FluMoS Professional CD-ROM 1 3371637
FluMoT CD-ROM 1 3355177 You will find other electrical and hydraulic accessories for fluid sensors in our general accessories brochure no. 7.623. This brochure can be downloaded free of charge from our website www.hydac.com.
ContaminationSensor CS 1939 en(us) Page 30 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Checking/resetting default settings
Checking/resetting default settings
Dialog menu
User Settings Value HSI Slave Address a
Measurement Period 60
Calibrating ContaminationSensor
We recommend calibrating the sensor every two to three years unless otherwise specified. You will find the authorized HYDAC Service stations in the "Finding Customer Service" chapter on page 34.
Technical Data
General data
Mounting position Any (recommended: vertical position)
Self diagnostics continuously with error indication via status LED and display
Measured variables ISO99 (ISO 4406:1999)
Service variables Flow Status
Drive %
Temp °C and °F
Permitted ambient temperature range -30 to 80 °C / -22 to 176 °F
Storage temperature range -40 … 80 °C / -40 … 176 °F
Permitted relative humidity max. 95%, non-condensing
Material of seal FKM
Protection class III (low voltage protection)
Protection class IP 67 (only with screw-lock connectors)
Weight ≈ 1.3 kg
ContaminationSensor CS 1939 en(us) Page 31 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Technical Data
Hydraulic data
Permitted operating pressure maximum 350 bar / 5075 psi
Hydraulic connection - Pipe or hose connection Thread G ¼ according to ISO 228 - Flange connection DN 4
Permitted measurement flow rate 30 … 500 ml/min
Permissible viscosity range 1 to 1000 mm²/s
Fluid temperature range 0 …80 °C / 32 …185 °F
Electrical data
Connection plug M12x1, 5 pole, specified in DIN VDE 0627
Power supply 9 … 36 V DC, residual ripple < 10%, (protected against polarity reversal)
Power consumption 3 W max.
CAN SAE J1939
HSI (HYDAC Sensor Interface) 1 wire, half duplex
ContaminationSensor CS 1939 en(us) Page 32 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Annex
Model code CS 1939 - 0 - 0 / - 000 Model CS = ContaminationSensor Series 1939 = Classification:
ISO 4406:1999; SAE AS 4059 (D) / >4 µm(c) >6 µm(c) >14 µm(c) > 21 µm(c) Interface / protocol: CAN / CAN SAE J1939 No display Electrical connection: Plug M12x1, 5-pin
Fluids 0 = based on mineral oil 1 = for phosphate esters Hydraulic connection type 0 = Pipe or hose connection 1 = Flange connection Modification number 000 = Standard
ContaminationSensor CS 1939 en(us) Page 33 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Finding Customer Service For calibration and repair, send the sensor to the following address:
Germany HYDAC Service GmbH Product Support, Werk 13 Friedrichsthaler Straße 15A 66540 Neunkirchen-Heinitz Telephone: +49 6897 509 883 Fax: +49 6897 509 324 E-mail: service@hydac.com
USA
HYDAC Technology Corporation, HYCON Division 2260 City Line Road USA-Bethlehem, PA 18017 P.O. Box 22050 USA-Lehigh Valley, PA 18002-2050 Telephone: +1 610 266 01 00 Fax: +1 610 231 04 45 E-mail: sales@hydacusa.com Internet: www.hydacusa.com
Australia
HYDAC Pty. Ltd. 109 Dohertys Road P.O. Box 224 AUS-3025 Altona North Telephone: +61 392 72 89 00 Fax: +61 393 69 89 12 E-mail: info@hydac.com.au
ContaminationSensor CS 1939 en(us) Page 34 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Brazil HYDAC TECNOLOGIA LTDA Estrada Fukutaro Yida, 225 CEP 09852-060 Cooperativa BR-São Bernardo do Campo – SÃO PAULO Telephone: +55 11 4393 6600 Fax: +55 11 4393 6617 E-mail: hydac@hydac.com.br Homepage www.hydac.com.br
China
HYDAC TECHNOLOGY (SHANGHAI) LIMITED 28 Zhongpin Lu Shanghai Minhang Economic & Technological Development Zone SHANGHAI 200245; P.R. CHINA Telephone: +86 21/64 63 35 10 Fax: +86 21/64 30 02 57 E-mail: hydacsh@hydac.com.cn
ContaminationSensor CS 1939 en(us) Page 35 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Cleanliness classes - brief overview Cleanliness class - ISO 4406:1999
In ISO 4406:1999, particle counts are determined cumulatively, i.e. > 4 µm(c), >6 µm(c) and >14 µm(c) (manually by filtering the fluid through an analysis membrane or automatically using particle counters) and allocated to measurement references. The goal of allocating particle counts to references is to facilitate the assessment of fluid cleanliness ratings. In 1999 the "old" ISO 4406:1987 was revised and the size ranges of the particle sizes undergoing analysis redefined. The counting method and calibration were also changed. This is important for the user in his everyday work: even though the measurement references of the particles undergoing analysis have changed, the cleanliness code will change only in individual cases. When drafting the "new" ISO 4406:1999 it was ensured that not all the existing cleanliness provisions for systems had to be changed.
Table - ISO 4406 Assignment of particle counts to cleanliness classes: Particle count / 100 ml Particle count / 100 ml Class More than Up to (and
including) Class More than Up to (and
including) 0 0 1 15 16,000 32,000 1 1 2 16 32,000 64,000 2 2 4 17 64,000 130,000 3 4 8 18 130,000 250,000 4 8 16 19 250,000 500,000 5 16 32 20 500,000 1,000,000 6 32 64 21 1,000,000 2,000,000 7 64 130 22 2,000,000 4,000,000 8 130 250 23 4,000,000 8,000,000 9 250 500 24 8,000,000 16,000,000 10 500 1,000 25 16,000,000 32,000,000 11 1,000 2,000 26 32,000,000 64,000,000 12 2,000 4,000 27 64,000,000 130,000,000 13 4,000 8,000 28 130,000,000 250,000,000 14 8,000 16,000
ContaminationSensor CS 1939 en(us) Page 36 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Note: increasing the measurement reference by 1 causes the particle count to double. Example: ISO Code 18 / 15 / 11 says:
Cleanliness class Particle count / ml Size ranges 18 1,300 – 2,500 > 4 µm(c) 15 160 – 320 > 6 µm(c) 11 10 – 20 > 14 µm(c)
Overview of modifications - ISO4406:1987 <-> ISO4406:1999
"old" ISO 4406:1987
"new" ISO 4406:1999
Size ranges > 4 µm(c) > 5 µm > 6 µm(c) > 15 µm > 14 µm(c) Dimension determined
Longest dimension of a particle
Diameter of the coextensive circle ISO 11171:1999
Test dust ACFTD - dust 1-10 µm ultra fine fraction
ISO 12103-1A1
SAE Fine, AC – Fine
ISO 12103-1A2
SAE 5-80 µm ISO MTD Calibration dust for particle counters
ISO 12103-1A3
SAE Coarse Coarse fraction
ISO 12103-1A4
Comparable size ranges
Old ACFTD calibration
Comparable ACFTD dusts
New Nist calibration
----- < 1 µm 4 µm(c) 5 µm 4.3 µm 6 µm(c) 15 µm 15.5 µm 14 µm(c)
ContaminationSensor CS 1939 en(us) Page 37 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Explanation of terms and abbreviations An explanation of terms and abbreviations follows below:
AC Alternating current
ACFTD Air Cleaner Fine Test Dust
CAN Controller Area Network
CS ContaminationSensor
DC Direct current
DIN Deutsche Industrie Norm [German Industry Standard]
DN Nominal Diameter
EG European Community
Single measurement A single measurement means the analysis of the contamination in a sample, which flows through the sensor during the configured measurement period. The result of a single measurement is the measured value.
EU European Union
FluMoS FluidMonitoring Software, for details, see page 28.
FluMoT FluidMonitoring Toolkit
HMG HYDAC Measuring device
HSI HYDAC Sensor interface
IN Inlet
INLET Inlet
ISO Classification of the solid particle contamination, details see page 36.
ISO MTD ISO Medium Test Dust
LED Light-emitting diode
Measurement duration Once the measurement duration has elapsed, the measured value is updated which is shown on the display and presented at the interface. The measurement duration is configurable using the M.TIME parameter.
Measuring point This is the name for the point in the hydraulic system where a measurement is carried out.
Measurement Once a CS device has been connected to the electrical power and its boot process has completed, a single measurement will start, after which the next single measurement will
ContaminationSensor CS 1939 en(us) Page 38 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
immediately follow, and so on, until the CS device is disconnected from the power (MODE M1, M2, M4) or until the programmed target purity (MODE M3) has been reached. This series of single measurements is referred to as a measurement for convenience reasons.
Test volume Sample quantity which is analyzed for determining a measured value.
Measured value The contamination codes determined by a single measurement, shown as a three-digit ISO code or NAS codes or SAE codes of the individual particle size channels.
OUT Outlet
OUTLET Outlet
SAE Society of Automotive Engineers
ContaminationSensor CS 1939 en(us) Page 39 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
Index
A
Accessories ............................................. 17, 30 accident prevention ......................................... 9 ambient temperature ..................................... 31 Assignment ........................................24, 25, 36 Auxiliary personnel .................................. 11, 12
C
calibrating ...................................................... 31 Calibration................................................ 14, 37 care .............................................................. 2, 5 cleaning ......................................................... 29 Cleanliness .............................................. 36, 37 connecting .................................. 17, 20, 23, 28 Connection ........................................16, 25, 32 Connection cable ........................................... 25 Connection plug ............................................. 32 Console mounting .......................................... 18 Contamination class ................................ 36, 37 Contamination classes .................................. 36 ContaminationSensor .. 1, 9, 13, 14, 15, 18, 20,
21, 23, 24, 29, 31, 33, 38 Content ............................................................ 3
D
Date ............................................................... 13 default setting ................................................ 31 Description .................................. 13, 14, 26, 30 diagnostics ..................................................... 31 Differential pressure ...................................... 22 Dimensions .................................................... 15 DIN .............................................. 18, 25, 32, 38 Disposal ......................................................... 12 Documentation Representative ....................... 2
E
Electrical data ................................................ 32 Error ............................................................... 26
F
filtration .......................................................... 26 Firmware .......................................................... 1 Flange connection ...................... 17, 20, 32, 33 Flow rate ........................................................ 22 Fluid temperature .......................................... 32 Fluid temperature range ................................ 32 FluMoS ....................................... 14, 28, 30, 38
FluMoT .............................................. 28, 30, 38
G
GND ........................................................ 24, 25
H
half duplex ..................................................... 32 Hardware ........................................................ 1 Hazard symbol ............................................ 7, 8 HSI ........................................ 24, 25, 31, 32, 38 Hydraulic connection................... 16, 23, 32, 33 Hydraulic data ............................................... 32
I
Imprint ............................................................. 2 IN 38 Inlet ............................................................... 38 INLET .............................. 13, 16, 18, 20, 23, 38 installation ............................... 9, 12, 18, 20, 21 Interface ...................................... 24, 25, 32, 33 IP 31 ISO ... 16, 18, 19, 23, 27, 31, 32, 33, 36, 37, 38,
39 ISO4406 ........................................................ 37
1987 ......................................................................... 37 1999 ......................................................................... 37
M
Maintenance ....................................... 1, 12, 30 Manufacturer ................................................... 2 Measured value ............................................ 39 Measured variable ........................................ 31 Measurement .......................................... 31, 38 Measures ........................................................ 8 measuring ............................................... 21, 26 Measuring point ............................................ 38 MODE ........................................................... 38 Model code ............................................. 13, 33 mounting ........................................... 17, 18, 19 Mounting position .......................................... 31
N
NAS ............................................................... 39
ContaminationSensor CS 1939 en(us) Page 40 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
Annex
O
operating .. 5, 6, 7, 9, 11, 12, 13, 15, 20, 23, 26, 32
Operation ................................................. 10, 12 Operations control ......................................... 12 OUT ............................................................... 39 Outlet ............................................................. 39 OUTLET................................ 16, 18, 20, 23, 39 Overview ........................................................ 37
P
Power consumption ....................................... 32 Proper/Designated Use ................................... 9 Protection class ............................................. 31
R
Relative humidity ........................................... 13 Remedy ......................................................... 26
S
SAE ........................... 24, 25, 27, 32, 33, 37, 39
select ......................................................... 6, 21 Sensor ......................................... 24, 25, 32, 38 Serial-no ........................................................ 13 Service .............................................. 26, 31, 34 Service variable ............................................ 31 Signal word ..................................................... 8 signal words .................................................... 8 Single measurement ..................................... 38 Size ............................................................... 37 Specialist personnel ................................ 11, 12 Storage conditions ........................................ 13 Storage temperature ............................... 13, 31 Storage temperature range ........................... 31 Supply voltage ........................................ 24, 25
T
Test volume .................................................. 39 Transport ....................................................... 12 troubleshooting ............................................. 26 Troubleshooting ............................................ 12
W
Wall mounting ............................................... 18 Weight ........................................................... 31
ContaminationSensor CS 1939 en(us) Page 41 / 44
BeWa CS1939 3978342a V100 en-us 2017-07-14.docx 2017-07-14
HYDAC FILTER SYSTEMS GMBH Industriegebiet Postfach 1251 66280 Sulzbach/Saar 66273 Sulzbach/Saar Germany Germany Tel: +49 6897 509 01 Central Fax: +49 6897 509 9046 Technology Fax: +49 6897 509 577 Sales Department Internet: www.hydac.com E-mail: filtersystems@hydac.com
top related