coal liquefaction

Coal LiquefactionBy : Nurhua Kumala Sari

Coal Liquefaction??

• Convert coal to liquid• The purpose of this process is to producing liquid

fuels from coal

Fuels H/C Ratios

• To make liquid fuels from coal -need to add hydrogen or reject carbon

•To make liquid fuels from natural gas -need to reject hydrogen or add carbon

DCL

ICL

CTL

Direct Coal Liquefaction (DCL)

• Direct coal liquefaction starts just prior to World War II by Germany, continues through the 1950s and 1960s with the research by the U.S.

• Direct coal liquefaction refers to the direct reaction of coal with hydrogen to form liquids.

• The hydrogen is also required to increasing the H/C ratio of the coal as it is liquefied. One of the key differences between coal and petroleum is the much lower H/C atomic ratio of coal (0.7 vs 1.5 for petroleum )

• Direct liquefaction involves the addition of hydrogen to coal in a solvent slurry at elevated temperature and pressure.

• Coal dissolution is accomplished under high temperature (~400 0C) and pressure (~1500-3000 psi) with hydrogen and a coal-derived solvent.

• The principal products of a direct-liquefaction CTL plant would be naphtha and middle distillates.

• direct-liquefaction products contain more aromatic and cyclic hydrocarbons and fewer paraffins, and they have a lower overall hydrogen content.

• prospective yields are reported to be between 2.7 and 3.0 barrels per ton of as-received coal

• theoretical efficiency can be high…roughly 70-75%

Direct Liquefaction Process

• A single-stage direct liquefaction process

process gives distillates via one primary reactor.

• A two-stage direct liquefaction process

processis designed to give distillate products via two reactor stages in series. The primary function of the first stage is coal dissolution and is operated either without a catalyst or with only a low-activity disposable catalyst.

A single-stage direct liquefaction process

• SRC-II• Exxon Donor Solvent (EDS)• H-Coal

EDS

• Coal is slurried with a distillable recycled solvent that has been rehydrogenated to restore its hydrogen donation capacity

• The slurry is mixed with H2, preheated and fed to a simple up-flow tubular reactor that operates at 425-450 ºC and 2575 psig .

• No catalyst is added to liquefaction reactor• Yields of up to 47% for lignites, 50% for sub-

bituminous coals and 60% for bituminous coals could be achieved.

H-Coal

• This reactor operates at temperatures of 425-455°C and a pressure of 2900 psig

• H2 is added and the mixture is preheated and fed to an ebullated bed hydrocracker

• A conventional supported hydrotreating catalyst, either Ni-Mo or Co-Mo alumina is used.

• As with other processes, yields are dependent on the coal. >95% overall conversion can be obtained with suitable coals, with liquid yields up to 50% (dry basis).

A two-stage direct liquefaction process

• Integrated Two-Stage Liquefaction (ITSL)

• Catalytic Multi-stage Liquefaction (CMSL)

ITSL

MTSL

Indirect Coal Liquefaction

• In Indirect Liquefaction (IL) coal is first gasified to form syngas. Syngas is then converted to liquids by means of a catalyst and Fischer Tropsch (FT) chemistry

• Synthesis Gas or Syngas –mixture of CO, H2, CO2, H2O

• theoretical efficiency is lower…roughly 60-65%

• The process begins with the gasification of coal• reacting coal with steam and oxygen at elevated

temperatures (1,000 to 1,500 degrees Celsius) and moderate pressure(~500 pounds per square inch [psi])

• The naphtha product is basically a very low–octane (i.e., about 40 octane) gasoline that must be extensively upgraded before it can be used as an automotive fuel.

• Conversion of synthesis gas to hydrocarbons is highly exothermic (i.e., it releases heat).

The Methanol-to-Gasoline Coal-to-Liquids (MTG CTL)

• The front end of an MTG CTL plant would be similar to that of an FT CTL plant.

gasified

Synthesis of methanol

Produce gasoline from

mehanol

MTG CTL steps

Very exotermic

(200 to 300 degreesCelsius, about 750 psi)

• To better control this heat release,methanol is first dehydrated to produce dimethyl ether.

• After upgrading and separations, the liquid-fuel yield of an MTG CTL plant would be about 90-percent gasoline, with most of the remainder being LPG.

• MTG reactor does not produce any of the heavy hydrocarbons generally found in diesel oil, jet fuel, and heavy oils and waxes.

Thankyou :D