camd assembly
Post on 10-Oct-2015
68 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
Bench Vice Assembly 1
In this project, you will create the Bench Vice assembly. Figures B through E shows the viewsand dimensions of the components of the Bench Vice assembly.
Bench Vice Assembly
Figure 2 Views and dimensions of the base
Figure 1 The Bench Vice assembly
CAMD_ProE_Assembly 1 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 4 Views and dimensions of various components of the Bench Vice assembly
Figure 3 Views and dimensions of the Vice Jaw
CAMD_ProE_Assembly 2 MIT College of Engineering, Pune - 411038.
-
Bench Vice Assembly 3
Figures 5 Views and dimensions of various components of the Bench Vice assembly
CAMD_ProE_Assembly 3 MIT College of Engineering, Pune - 411038.
-
Butterfly Valve Assembly 1
Create the components of the Butterfly Valve assembly and then assemble them, as shown inFigure 1. The dimensions of the components are shown in Figures 2 through 7. Assume themissing dimensions.
Butterfly Valve Assembly
Figure 1 The Butterfly Valve assembly
Figure 2 Dimensions of the BodyCAMD_ProE_Assembly 4 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 4 Dimensions of the RetainerFigure 3 Dimensions of the Shaft
Figure 6 Sectional front view of the ArmFigure 5 Top view of the Arm
Figure 7 Dimensions of the Plate, Nut, and Screw
CAMD_ProE_Assembly 5 MIT College of Engineering, Pune - 411038.
-
V-Block Assembly 1
Figure 2 Views and dimensions of the V-Block body
Create all the components of the V-Block assembly and then assemble them, as shown inFigure 1. The dimensions of the components are shown in Figures 2 and 2.
V-Block Assembly
Figure 1 The V-Block assembly
CAMD_ProE_Assembly 6 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Views and dimensions of the U-Clamp and Fastener
CAMD_ProE_Assembly 7 MIT College of Engineering, Pune - 411038.
-
Crosshead Assembly 1
Crosshead Assembly
Figure 2 The exploded state of Crosshead assembly
Figure 1 The Crosshead assembly
In this project, you will create all components of the Crosshead assembly and then assemblethem, as shown in Figure 1. Also you will create an exploded state, shown in Figure 2. Thedimensions of the components are shown in Figures 3 through 7.
CAMD_ProE_Assembly 8 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Front view and the right-side view of the Body
Figure 5 Dimensions of Piston RodFigure 4 Dimensions of Keep Plate
Figure 6 Dimensions of the Brasses and Bolt
CAMD_ProE_Assembly 9 MIT College of Engineering, Pune - 411038.
-
Crosshead Assembly 3
Figure 7 Dimensions of Nut
CAMD_ProE_Assembly 10 MIT College of Engineering, Pune - 411038.
-
Double Bearing Assembly 1
In this project, you will create the Double Bearing assembly shown in Figure 1. The explodedstate of the assembly is shown in Figure 2 and the dimensions of the components of theDouble Bearing assembly are shown in Figures 3 through 7.
Double Bearing Assembly
Figure 4 Top view of the CapFigure 3 Top view of the Base
Figure 2 The exploded view of the DoubleBearing assembly
Figure 1 The completed Double Bearingassembly
Figure 6 Front view of the CapFigure 5 Front view of the BaseCAMD_ProE_Assembly 11 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 7 Dimensions and drawing views of the Bushing and the Bolt
CAMD_ProE_Assembly 12 MIT College of Engineering, Pune - 411038.
-
Fixture Assembly 1
Create all the components of the Fixture assembly and then assemble them, as shown inFigure 1. The details of the components of the Fixture assembly are shown inFigures 2 through 5.
Fixture Assembly
Figure 1 The Fixture assembly
Figure 2 Dimensions of the End Plate
CAMD_ProE_Assembly 13 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Dimensions of the Disk
Figure 4 Dimensions of the Support Pin and the Bolt
CAMD_ProE_Assembly 14 MIT College of Engineering, Pune - 411038.
-
Fixture Assembly 3
Figure 5 Dimensions of the Spacer, Center Pin, and the Nut
CAMD_ProE_Assembly 15 MIT College of Engineering, Pune - 411038.
-
Plummer Block Assembly 1
Figure 2 Views and dimensions of the Casting
In this project, you will create the components of the Plummer Block assembly, as shown inFigure 1 and then assemble them. The dimensions of the components are given in Figures 2through 4.
Plummer Block Assembly
Figure 1 The Plummer Block assembly
CAMD_ProE_Assembly 16 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Views and dimensions of the Cap
Figure 4 Views and dimensions of Brasses, Nut, Lock Nut, and Bolt
CAMD_ProE_Assembly 17 MIT College of Engineering, Pune - 411038.
-
Press Tool Assembly 1
In this project, you will create the Press Tool assembly shown in Figure 1. The exploded stateof the assembly is shown in Figure 2 and the dimensions of the components of the Press Toolassembly are shown in Figures 2 through 5.
Press Tool Assembly
Figure 1 The completed Press Tool assembly after assembling theTop Plate with the assembly
Figure 2 The exploded view of the Press Tool as-sembly
Figure 3 Figure showing the Bottom Plate
CAMD_ProE_Assembly 18 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 5 Dimensions and views of the Guide Pillarand Guide Bush
Figure 4 Dimensions and views of the TopPlate
CAMD_ProE_Assembly 19 MIT College of Engineering, Pune - 411038.
-
Pulley Support Assembly 1
Figure 2 Exploded view of the Pulley Support assembly
Create the components of the Pulley Support assembly and then assemble them, as shown inFigure 1. After creating the assembly, create its exploded view, as shown in Figure 2. Thedimensions of the components are given in Figures 4 through 8.
Pulley Support Assembly
Figure 1 The Pulley Support assembly
CAMD_ProE_Assembly 20 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 8 Dimensions of the Washer, Cap Screw, Turn Screw, and Nut
Figure 5 Dimensions of the BushingFigure 4 Dimensions of the Pulley
Figure 7 Sectioned front view of theFigure 6 Left-side view of the Bracket
CAMD_ProE_Assembly 21 MIT College of Engineering, Pune - 411038.
-
Pulley Support Assembly 3
Figure 3 Parts list for the Pulley Support assembly
CAMD_ProE_Assembly 22 MIT College of Engineering, Pune - 411038.
-
Shock Assembly 1
Shock Assembly
Figure 1 The Shock assembly
In this project, you will create all components of the Shock assembly and then assemblethem, as shown in Figure 1. Also create an exploded state of the assembly, as shown inFigure 2. The dimensions of the components are shown in Figures 3 through 10.
Figure 2 The exploded state of the Shock Assembly
CAMD_ProE_Assembly 23 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 4 Dimensions for PivotFigure 3 Dimensions for Bracket
Figure 5 Dimensions for U-Support
CAMD_ProE_Assembly 24 MIT College of Engineering, Pune - 411038.
-
Shock Assembly 3
Figure 9 Dimensions for Hexagonal boltFigure 8 Dimensions for Washer
Figure 6 Dimensions for Bushing Figure 7 Dimensions for Self-locking nut
Figure 10 Dimensions for Castle nut
CAMD_ProE_Assembly 25 MIT College of Engineering, Pune - 411038.
-
Wheel Support Assembly 1
Create all the components of the Wheel Support assembly and then assemble them, as shownin Figure 1. The dimensions of the components are shown in Figures 2 through 6.
Wheel Support Assembly
Figure 1 The Wheel Support assembly
Figure 9-3 Dimensions of the SupportFigure 2 Dimensions of the Base
Figure 5 Sectioned side view of the WheelFigure 4 Front view of the Wheel
CAMD_ProE_Assembly 26 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 6 Dimensions of the Shoulder Screw, Bolt, Nut, Bushing,and Washer
CAMD_ProE_Assembly 27 MIT College of Engineering, Pune - 411038.
-
Pipe Vice Assembly 1
In this Project, you will create all components of the Pipe Vice assembly, as shown inFigure 1, and then assemble them. The dimensions of the components are given inFigures 2 and 3.
Figure 1 The Pipe Vice assembly
Pipe Vice Assembly
Figure 2 Views and dimensions of the Base
CAMD_ProE_Assembly 28 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Views and dimensions of the Screw, Handle, Movable Jaw, and Handle Screw
CAMD_ProE_Assembly 29 MIT College of Engineering, Pune - 411038.
-
Shaper Tool Head Assembly 1
Create the Shaper Tool Head assembly, as shown in Figure 1. After creating the assembly, createits exploded view, as shown in Figure 2. The dimensions of the components are given inFigures 3 through 7.
Shaper Tool Head Assembly
Figure 1 The Shaper Tool Head assembly
Figure 2 The exploded view of the Shaper ToolHead assembly
CAMD_ProE_Assembly 30 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Views and dimensions of the Swivel Plate
CAMD_ProE_Assembly 31 MIT College of Engineering, Pune - 411038.
-
Shaper Tool Head Assembly 3
Figure 4 Views and dimensions of the Back Plate
CAMD_ProE_Assembly 32 MIT College of Engineering, Pune - 411038.
-
4 Student Project
Figure 5 Views and dimensions of the Vertical Slide
CAMD_ProE_Assembly 33 MIT College of Engineering, Pune - 411038.
-
Shaper Tool Head Assembly 5
Figure 6 Views and dimensions of various components
CAMD_ProE_Assembly 34 MIT College of Engineering, Pune - 411038.
-
Stock Bracket Assembly 1
Figure 2 Top and front views of the Stock Support Base
In this project, you will create the Stock Bracket assembly shown in Figure 1. The details ofthe components of the Stock Bracket assembly are shown in Figures 2 through 8.
Stock Bracket Assembly
Figure 1 The Stock Bracket assembly
CAMD_ProE_Assembly 35 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 4 Top and front views of the Adjusting ScrewNut
Figure 3 Front and right-side views of the StockSupport Roller
Figure 6 Views of the Adjusting Nut Handle andAdjusting Screw Guide
Figure 5 Front and right-side views of the Support Roller Bracket
CAMD_ProE_Assembly 36 MIT College of Engineering, Pune - 411038.
-
Stock Bracket Assembly 3
Figure 8 Top and front views of the ThrustBearing
Figure 7 Views of the Support Adjusting Screw
CAMD_ProE_Assembly 37 MIT College of Engineering, Pune - 411038.
-
Motor Blower Assembly 1
In this project, you will create the Motor Blower assembly shown in Figure 1. The explodedview of the assembly is shown in Figure 2. The details of the components of the Motor Blowerassembly are shown in Figures 3 through 8.
Figure 1 Motor Blower assembly
Figure 2 Exploded view of the Motor Blower assembly
Motor Blower Assembly
CAMD_ProE_Assembly 38 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 3 Dimensions of the Upper Housing
Figure 4 Dimensions of the Lower Housing
CAMD_ProE_Assembly 39 MIT College of Engineering, Pune - 411038.
-
Motor Blower Assembly 3
Figure 5 Dimensions of the Blower
Figure 6 Dimensions of the Motor
CAMD_ProE_Assembly 40 MIT College of Engineering, Pune - 411038.
-
4 Student Project
Figure 8 Dimensions of the Shaft
Figure 7 Dimensions of the Cover
CAMD_ProE_Assembly 41 MIT College of Engineering, Pune - 411038.
-
Radial Engine Assembly 1
In this project, you will create the Radial Engine assembly shown in Figures 1 and 2. TheRadial Engine assembly will be created in two parts, one will be the subassembly and theother will be the main assembly. The dimensions of the components of the Radial Engineassembly are shown in Figures 3 through 6.
Radial Engine Assembly
Figure 1 The Radial Engine assembly Figure 2 The exploded view of the assembly
Figure 3 Views and dimensions of the Piston
CAMD_ProE_Assembly 42 MIT College of Engineering, Pune - 411038.
-
2 Student Project
Figure 5 Views and dimensions of the Master Rod
Figure 4 Views and dimensions of the Articulated Rod
CAMD_ProE_Assembly 43 MIT College of Engineering, Pune - 411038.
-
Radial Engine Assembly 3
Figure 6 Views and dimensions of the Rod Bush Upper, Rod Bush Lower, Piston Pin Plug,Piston Pin, Piston Rings, and Master Rod Bearing
CAMD_ProE_Assembly 44 MIT College of Engineering, Pune - 411038.
01 Bench Vice Assembly02 Butterfly Valve Assembly03 V-block Assembly04 Crosshead Assembly05 Double Bearing Assembly06 Fixture Assembly07 Plummer Block Assembly08 Press Tool Assembly09 Pulley Support Assembly10 Shock Assembly11 Wheel Support Assembly12 Pipe Vice Assembly13 Shaper Tool Head Assembly14 Stock Bracket Assembly15Motor blower Assembly16 Radial Engine Assembly
top related