calibre wiring guide

GROUND#8 X 1/2" TEK

IGNITIONSWITCHED+12 VOLTS

BLACKRED

BROWN

BLUE

GRAYWHITE

GR

AY

GR

AY

WH

ITE

BL

UE

INTERIOR NETWORK MODULE

FRONTRADAR

LED

REARRADAR

LED(CALIBRE DL

model only)

RECEIVERCABLE

FRONT

AMPLIFIED SPEAKER

REAR LASER DEFUSER(OPTIONAL)

+12 VOLT BATTERY

OR IGNITION SOURCE

BLUE

YELLOW*

BROWN*

BLACK

BLACKCABLE

FUSECONNECTION

GROUND#8 X 1/2" TEK

1AMP

YELLOW*

BROWN*

BLACK

FRONT LASER DEFUSER(OPTIONAL)

+12 VOLT BATTERY

OR IGNITION SOURCE

YELLOW*

BROWN*

WHITE

BLACK

BLACKCABLE

FUSECONNECTION

1AMP

GROUND#8 X 1/2" TEK

YELLOW*

BROWN*

BLACK

RECEIVERCABLE

REAR

BLOCK DIAGRAM

*THE YELLOW AND BROWNRADAR RECEIVER WIRESARE USED TO CONNECT TOTHE OPTIONAL LASERDEFUSER. IF NO LASERDEFUSER IS BEINGINSTALLED WITH THERADAR RECEIVER (FRONTAND/OR REAR), THE YEL-LOW AND BROWN WIRESWILL NOT BE USED.

CALIBRE

44586-2 07/07

IGNITION AND GROUND1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when

ignition key is both on and cranking.

2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self-tapping screw.

3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source.

*NOTE: THE RED WIRESHOULD BE CONNECTED TO A MINIMUM 16 GAUGE+12 VOLT IGNITION WIRE.

GROUND#8 X 1/2" TEK

IGNITIONSWITCHED+12 VOLTS

BLACKRED

BROWN

BLUE

GRAYWHITE

GR

AY

GR

AY

WH

ITE

BL

UE

INTERIOR NETWORK MODULE

FRONTRADAR

pod

REARRADAR

pod(CALIBRE DL-P

model only)

FRONT LASER DEFUSER

RECEIVERCABLE

(OPTIONAL)

AMPLIFIED SPEAKER

REAR LASER DEFUSER(OPTIONAL)

+12 VOLT BATTERY

OR IGNITION SOURCE

BLUE

YELLOW*

BROWN*

BLACK

BLACKCABLE

FUSECONNECTION

GROUND#8 X 1/2" TEK

1AMP

YELLOW*

BROWN*

BLACK

+12 VOLT BATTERY

OR IGNITION SOURCE

YELLOW*

BROWN*

WHITE

BLACK

BLACKCABLE

FUSECONNECTION

1AMP

GROUND#8 X 1/2" TEK

YELLOW*

BROWN*

BLACK

FRONT

RECEIVERCABLE

REAR

BLOCK DIAGRAM

IGNITION AND GROUND1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when

ignition key is both on and cranking.

2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self-tapping screw.

3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source.

*THE YELLOW AND BROWNRADAR RECEIVER WIRESARE USED TO CONNECTTO THE OPTIONAL LASERDEFUSER(S). IF A LASERDEFUSER IS NOT BEINGINSTALLED WITH A RADARRECEIVER (FRONT AND/ORREAR), THE YELLOW ANDBROWN WIRES WILL NOT BE USED.

CALIBRE*NOTE: THE RED WIRESHOULD BE CONNECTED TO A MINIMUM 16 GAUGE+12 VOLT IGNITION WIRE.