basics of golf club shaft trimming
Post on 29-Nov-2014
8.817 Views
Preview:
DESCRIPTION
TRANSCRIPT
Basics of Shaft InstallationUnderstanding The Principals of
Tip Trimming Instructions
Thursday June 4, 20092-3PM Eastern Standard Time
Audio settings are set on listen only.Please post questions in the upper right hand corner Chat box.
Question & Answer period will be at end of webinar.www.hirekogolf.com
800 367-8912
with Jeff SummittTechnical Director, Hireko Golf
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICES
…did you ever play the game Simon says as a kid?
Remember the phrase your father, grandfather or shop teacher said:“Measure twice, cut once”?
Shaft trimming procedures use these same basic principles
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Why trim the shaft at all? • Manufacturers produce longer-than-normal raw length
shafts to accommodate a wide range of golfer’s heights
• Trimming the shaft also controls the flex
• Each manufacturer has logical reason why they suggest the recommended trimming
Anatomy of the ShaftUnitized – To decrease inventory, one shaft can be used to build an entire set of irons and one shaft can be used to build an entire set of woods through successive trimming of the tip section.
Parallel tip - The tip is one constant diameter up to a certain point on the shaft.Typical diameters are typically .335" and .350" for woods, and .370" and for irons.
Taper tip - The tip is made to gradually increase larger in diameter from the tip up to a specified point on the shaft. Taper tip steel shafts are made with a .0075"/ inch tapering rate on irons up to the beginning of the tip parallel section. A common tip taper diameter for OEM irons is .355".
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Do You Trim the Butt, Tip or Both Ends? It often depends upon the length of the
parallel tip section, for instance:
Unitized steel shafts have long parallel tip sections and generally are trimmed
in ½” increments per club.
Graphite shafts generally have shorter parallel tip sections than steel.
Therefore the shafts might be trimmed in smaller increments per club, but can
be as much as ½” too.
Tapered shafts cannot be tip trimmed – everything comes from the butt end otherwise the shaft will not fit inside
the corresponding hosel diameter.
Where do you find the trimming information? • Shaft manufacturer’s website
• Component companies will either place this information in their catalog, website or send out on a piece of paper with each order
• Charts and nomenclature may be different from each manufacturer, results the same
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Hireko’s Trimming Information Method 1. Find the shaft specification table in catalog or on the website
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Hireko’s Trimming Information Method 2. Look up trim chart and club head # for tip trimming amount (if any)
Hireko’s Trimming Information Method 3. Pay attention to any trimming notes that may apply
TRIMMING NOTES
1. For M1 metal woods add 1 1/2" tip trimming, for M2 metal woods add 1" tip trimming, for blind bore add 1/2" tip trimming, for through bore do not add to tip trimming. (Applies only to those shafts which have a Trim Note 1 next to the letter code)2. For non-bore through iron heads, trim 1" additionally from the tip. (Applies to True Temper's TT Lite R&S iron shafts only!) 3. For fairway woods, tip trim 1" (Applies to Aldila NV, NVS, DVS, VS Proto and Voodoo woods only!) 4. Do not tip trim more than 3” off the tip (applies to Select New Image woods and junior composite woods only!)
Remember to read the small print…
Bore Types: Woods
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Bottom of Bore to Ground Line:Hybrids, Irons and Wedges
• Pay close attention when mixing and matching club
head models with different shafts
• Use the same principles used in woods to
standardize trimming in order to maintain flex
• Insert shaft into the hosel and measure overall length, subtract the raw length of the shaft yielding the bottom of bore to ground line
Combination Flex ShaftsThere are five primary flexes. These are referred to as “discrete flexes”.
Ladies (L), Senior (A), Regular (R), Stiff (S) and Extra Stiff (X)
Shafts can be made to possess two (or more) separate flexes within a single shaft. These are commonly called “combination flex” and used to cut down on inventory.
Combination Flexes Manufacturer’s Designations L and A combination flexes A&L or A/L R and S combination flexes R&S or R/S A and R combination flexes A&R or A/R S and X combination flexes S&X or S/X
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICESSales 800 367-8912
Free Technical Service 800 942-5872
Combination Flex Shafts: Examples, Hybrids, In-between flexes
MANUFACTURER / BRAND SHAFT TYPE FLEX(S)
TRIMCHART
TRUE TEMPER Dynalite A&L Iron L AA
Dynalite A&L Iron A BB
Dynalite R&S Iron R AA
Dynalite R&S Iron S CC
2009 HIREKO TIP TRIMMING TABLES FOR IRONS & HYBRIDS Hybrid Hybrid 1 iron 2 iron 3 iron 4 iron 5 iron 6 iron 7 iron 8 iron 9 iron Wedges
216g 223g 229g 236g 243g 250g 257g 264g 271g 278g 285g 291+g
AA 0" 0" 0" 0.5" 1" 1.5" 2" 2.5" 3" 3.5" 4" 4"
BB 0" 0.5" 1" 1.5" 2" 2.5" 3" 3.5" 4" 4.5" 5" 5"
CC 1" 1.5" 2" 2.5" 3" 3.5" 4" 4.5" 5" 5.5" 6" 6"
…and when in doubt, double check with a reliable source
PROFESSIONAL GOLF CLUBS AT DOWN TO EARTH PRICES
THANK YOU FOR ATTENDING!Go online at www.HirekoGolf.com and click on Webinars banner for schedule.
A link pointing you to today’s webinar will be emailed to you in a few hours.
Act now and get 15% off all high performanceTrue Ace Cadence Shafts
Use coupon code 649Offer Expires in 48 hours so act now.
Jeff Summitt,Technical Directorjsummitt@hirekogolf.com
Technical Support 800 942-5872www.HirekoGolf.comSales 800 367-8912
top related