arib std-t64-lpr-0 v1.0 the low power repeaters …...arib std-t64-lpr-0 v1.0 the low power...
Post on 28-Mar-2020
16 Views
Preview:
TRANSCRIPT
ARIB STD-T64-LPR-0 v1.0
The Low Power Repeaters for cdma2000 Cellular Telephones
Refer to "Industrial Property Rights (IPR)" in the preface of ARIB STD-T64 for Related
Industrial Property Rights. Refer to "Notice" in the preface of ARIB STD-T64 for Copyrights
Original Specification This standard, ARIB STD-T64-LPR-0 v1.0, was prepared by 3GPP2-WG of Association of
Radio Industries and Businesses (ARIB).
Modification to the original specification Not Applicable.
Notes
None.
ARIB STD-T64-LPR-0 v1.0
-i-
Contents
Chapter 1 General Descriptions.......................................................................................................1
1.1 Outline .................................................................................................................................1
1.2 Scope of the Standard..........................................................................................................1
Chapter 2 References........................................................................................................................2
2.1 Reference Regulations .........................................................................................................2
2.2 Reference Documents ..........................................................................................................2
2.3 Terms and Definitions .........................................................................................................2
Chapter 3 General Requirements ....................................................................................................4
3.1 RF Signals............................................................................................................................4
3.1.1 Operating Frequency Bands.........................................................................................4
3.1.2 Type of Repeating..........................................................................................................4
3.1.3 Mode of Radio Communications...................................................................................4
3.2 Compliance to the Radio Protection Policy ........................................................................4
Chapter 4 Frequency Bands and Channel Arrangement ...............................................................5
4.1 Frequency Bands .................................................................................................................5
4.2 TX - RX Frequency Separation ...........................................................................................5
4.3 Channel Arrangement .........................................................................................................5
4.3.1 Channel Spacing ...........................................................................................................5
4.3.2 Channel Designation ....................................................................................................6
4.3.2.1 Band Class 0 (800 MHz Band)...............................................................................6
4.3.2.2 Band Class 3 (JTACS Band) ..................................................................................7
4.3.2.3 Band Class 6 (2 GHz Band) ...................................................................................9
Chapter 5 Output Power ................................................................................................................10
5.1 Maximum Output Power...................................................................................................10
5.1.1 Minimum Requirements .............................................................................................10
5.2 Maximum Antenna Gain...................................................................................................10
Chapter 6 Frequency Error ............................................................................................................12
6.1 Test Requirements.............................................................................................................12
Chapter 7 Out of Band Gain ..........................................................................................................13
7.1 Minimum Requirements ...................................................................................................13
Chapter 8 Occupied Bandwidth .....................................................................................................14
8.1 Minimum Requirement .....................................................................................................14
ARIB STD-T64-LPR-0 v1.0
-ii-
Chapter 9 Modulation Requirements ............................................................................................15
9.1 Waveform Quality..............................................................................................................15
9.1.1 Method of Measurement.............................................................................................15
9.1.2 Test Requirement........................................................................................................15
Chapter 10 Transmitter Spurious Emission .................................................................................16
10.1 Uplink Spurious Emissions Requirements ....................................................................16
10.1.1 Test requirements .....................................................................................................16
10.1.2 Protection of PHS......................................................................................................17
10.2 Downlink Spurious Emissions Requirements................................................................18
10.2.1 Test requirements .....................................................................................................18
10.2.2 Protection of PHS......................................................................................................19
Chapter 11 Receiver Spurious Emissions......................................................................................20
11.1 Test Requirements ...........................................................................................................20
Chapter 12 Requirements for a Blanket License Application ......................................................23
Chapter 13 Requirements for Interference Avoidance to Other Radio Stations .........................24
Chapter 14 Measurements .............................................................................................................25
Change History ...............................................................................................................................26
Change History List of Standards .................................................................................................27
ARIB STD-T64-LPR-0 v1.0
-1-
Chapter 1 General Descriptions 1
1.1 Outline 2
This ARIB STANDARD specifies requirements of the Low Power Repeaters for cdma2000®1 3 (hereinafter referred to as “cdma2000 repeater”) operated in the frequency bands of 800 MHz, 4
and 2 GHz those are assigned for IMT-2000 in non-reproduction relay manner. The 5
requirements are compliant to the paragraphs 3 through 5, Regulation Article 49.6 of the 6
Ordinance Regulating Radio Equipment (this refers to the radio equipment of the land mobile 7
stations which function as repeaters as well as the radio equipment of Code Division Multiple 8
Access (CDMA) cellular telephone base stations, CDMA cellular telephone land mobile stations 9
or radio stations communicating for testing purpose of the radio equipment of CDMA cellular 10
telephones) and other related Regulation Articles. 11
12
1.2 Scope of the Standard 13
The cdma2000 repeater consists of RF amplifiers and antennas in both uplink and downlink 14
directions. The scope of this standard is shown in Figure 1-1. This standard specifies the 15
minimum radio frequency performance requirements of the cdma2000 repeater to be deployed 16
under the blanket license in Japan. 17
18
19
20
21
22
23
24
25
26
Figure 1-1 Repeater configured with separate amplifiers 27
28
1 cdma2000® is the trademark for the technical nomenclature for certain specifications and
standards of the Organizational Partners (OPs) of 3GPP2. Geographically (and as of the date of publication), cdma2000® is a registered trademark of the Telecommunications Industry Association (TIA-USA) in the United States.
Scope of this Standard
RF Amplifiers
Toward Base Station Base
Station
Mobile
Station
Toward Mobile Station
ARIB STD-T64-LPR-0 v1.0
-2-
Chapter 2 References 1
2.1 Reference Regulations 2
The referenced regulations are as follows: 3
RERL: Regulations for Enforcement of Radio Law; 4
ORE: Ordinance Regulating Radio Equipment; 5
OTRCC: Ordinance Concerning Technical Regulations Conformity Certification etc. of 6
Specified Radio Equipment; 7
OTF Ordinance Concerning Terminal Facilities etc; 8
RTCCA Rules Concerning the Technical Conditions Compliance Approval etc. for 9
Terminal Equipment; and 10
NT Notification of the Ministry of Posts and Telecommunications if issued in 2000 or 11
earlier, and a Notification of the Ministry of Internal Affairs and 12
Communications if issued in 2001 or later. 13
The requirements are translated into English from the Japanese regulations in Ministry of 14
Internal Affairs and Communications Ordinances and related Notifications. The original 15
regulation in Japanese prevails if any ambiguity is found between the requirements in those 16
Chapters and the original regulations. 17
2.2 Reference Documents 18
The following documents are referred in this standard. 19
[1] ITU-R Recommendation SM.329: "Unwanted emissions in the spurious domain". 20
[2] 3GPP2 C.S0051-0 “Recommended Minimum Performance Standards for 21
cdma2000 Repeaters ". 22
[3] 3GPP2 C.S0057-C “Band Class Specification for cdma2000 Spread Spectrum 23
Systems”. 24
2.3 Terms and Definitions 25
Band Class: A set of frequency channels and a numbering scheme for these channels. 26
CDMA: Code Division Multiple Access. A technique for spread-spectrum 27
multiple-access digital communications that creates channels through the 28
use of unique code sequences. 29
CDMA Channel: The set of channels transmitted from the Base station and the mobile 30
stations on a given frequency. 31
Downlink: Signal path where base station transmits and mobile station receives. 32
ARIB STD-T64-LPR-0 v1.0
-3-
JTACS: A Japanese version of the TACS 1G analog cellular radio technology. 1
Pass band: The repeater can have one or several pass bands. The pass band is the 2
frequency range that the repeater operates in with operational 3
configuration. 4
Repeater: A device receives, amplifies and transmits the radiated or conducted RF 5
carrier both in the downlink direction and in the uplink direction. 6
Uplink: Signal path where mobile station transmits and base station receives. 7
8
ARIB STD-T64-LPR-0 v1.0
-4-
Chapter 3 General Requirements 1
2
This standard applies only to cdma2000 repeaters, which complies with the requirements for 3
the blanket license in Japan. The cdma2000 repeaters are utilized to improve the radio access 4
environments. 5
Unless otherwise stated, all requirements in this standard apply to both the uplink and 6
downlink directions. 7
3.1 RF Signals 8
9
3.1.1 Operating Frequency Bands 10
The operating frequency bands shall be 800 MHz and 2 GHz bands assigned for IMT-2000. 11
12
3.1.2 Type of Repeating 13
The cdma2000 repeater shall be of non-reproduction type. 14 15
3.1.3 Mode of Radio Communications 16
FDD mode is employed. 17
3.2 Compliance to the Radio Protection Policy 18
The cdma2000 repeater shall meet the Regulation Article 21.3 in the Regulations for 19
Enforcement of the Radio Law (this refers to a provision of safety guard against strength of 20
radio waves). 21
22
ARIB STD-T64-LPR-0 v1.0
-5-
Chapter 4 Frequency Bands and Channel Arrangement 1
4.1 Frequency Bands 2
The cdma2000 repeater is designed to operate in one or several pass bands within either of the 3
following paired frequency bands; 4
5
Table 4-1 Band Class list 6
Band Class Subfield Description
BAND_CLASS_0 800 MHz Cellular band
BAND_CLASS_3 832 to 925 MHz JTACS band
BAND_CLASS_6 2 GHz IMT-2000 band
7
4.2 TX - RX Frequency Separation 8
The cdma2000 repeater is designed to operate with the following TX to RX frequency 9
separation; 10
11
Table 4-2 TX-RX frequency separation 12
Band Class TX-RX Frequency Separation
BAND_CLASS_0 45 MHz
BAND_CLASS_3 55 MHz
BAND_CLASS_6 190 MHz
13
4.3 Channel Arrangement 14
15
4.3.1 Channel Spacing 16
The channel spacing of Band Class 0, 3 and 6 shall be as specified in Table 4-3-2, Table 4-3-5 17
and Table 4-3-7. 18
19
ARIB STD-T64-LPR-0 v1.0
-6-
4.3.2 Channel Designation 1
This section specifies the frequency parameters of the CDMA equipment. 2
3
4.3.2.1 Band Class 0 (800 MHz Band) 4
The Band Class 0 system designators for the CDMA equipment shall be as specified in Table 5
4-3-1, Table 4-3-2 and Table 4-3-3. 6
7
Table 4-3-1 Band Class 0 system frequency correspondence 8
Transmit Frequency Band (MHz) System Designator Band Subclass
Mobile Station Base Station
0 Not Applicable Not Applicable
1 Not Applicable Not Applicable
2 824.025 – 829.995 869.025 – 874.995 A
3 815.025 – 829.995 860.025 – 874.995
0 Not Applicable Not Applicable B
1 Not Applicable Not Applicable
9
Table 4-3-2 CDMA channel number to CDMA frequency assignment correspondence for Band 10
Class 0 11
Transmitter CDMA Channel Number Center Frequency for CDMA Channel (MHz)
1<N<799 0.030 N + 825.000
991<N<1023 0.030 (N – 1023) + 825.000 Mobile Station
1024<N<1323 0.030 (N – 1024) + 815.040
1<N<799 0.030 N + 870.000
991<N<1023 0.030 (N – 1023) + 870.000 Base Stations
1024<N<1323 0.030 (N – 1024) + 860.040
12
ARIB STD-T64-LPR-0 v1.0
-7-
Table 4-3-3 CDMA channel numbers and corresponding frequencies for Band Class 0 and 1
Spreading Rate 1 2
Transmit Frequency Band (MHz) Band
Subclass System
Designator
CDMA Channel Validity
CDMA Channel Number
Mobile Station Base Station
0 Not
Applicable
Not
Applicable Not Applicable Not Applicable Not Applicable
1 Not
Applicable
Not
Applicable Not Applicable Not Applicable Not Applicable
A’’
(1 MHz) Valid 991−1023 824.040−825.000 869.040−870.000
2 A
(5 MHz)
Valid
Not Valid
1-142
143-166
825.030-829.260
829.290-829.980
870.030-874.260
874.290-874.980
A’’’’
(9 MHz)
Not Valid
Valid
1024-1047
1048-1323
815.040-815.730
815.760-824.010
860.040-860.730
860.760-869.010
A’’
(1 MHz) Valid 991−1023 824.040−825.000 869.040−870.000 3
A
(5 MHz)
Valid
Not Valid
1-142
143-166
825.030-829.260
829.290-829.980
870.030-874.260
874.290-874.980
3
4
4.3.2.2 Band Class 3 (JTACS Band) 5
The Band Class 3 system designators for the CDMA equipment shall be as specified in Table 6
4-3-4, Table 4-3-5 and Table 4-3.6. 7
8
Table 4-3-4 Band Class 3 system frequency correspondence 9
Transmit Frequency Band (MHz) System Designator
Mobile Station Base Station
A
887.0125 – 888.9875
893.0125 – 898.0000
898.0125 – 900.9875
915.0125 – 924.9875
832.0125 – 833.9875
838.0125 – 843.0000
843.0125 – 845.9875
860.0125 – 869.9875
B Not Specified Not Specified
10
ARIB STD-T64-LPR-0 v1.0
-8-
1
Table 4-3-5 CDMA channel number to CDMA frequency assignment correspondence for Band 2
Class 3 3
Transmitter CDMA Channel Number Center Frequency for CDMA Channel (MHz)
1<N<799 0.0125 N + 915.000
801<N<1039 0.0125 (N – 800) + 898.000
1041<N<1199 0.0125 (N – 1040) + 887.000 Mobile Station
1201<N<1600 0.0125 (N – 1200) + 893.000
1<N<799 0.0125 N + 860.000
801<N<1039 0.0125 (N – 800) + 843.000
1041<N<1199 0.0125 (N – 1040) + 832.000 Base Stations
1201<N<1600 0.0125 (N – 1200) + 838.000
In this table, only even-valued N values are valid. 4 5
Table 4-3-6 CDMA channel numbers and corresponding frequencies for Band Class 3 and 6
Spreading Rate 1 7
Transmit Frequency Band (MHz) System
Designator
CDMA Channel
Validity
CDMA Channel
Number Mobile Station Base Station
A1
(2 MHz)
Not Valid
Valid
Not Valid
1041–1099
1100–1140
1141–1199
887.0125–887.7375
887.7500–888.2500
888.2625–888.9875
832.0125–832.7375
832.7500–833.2500
833.2625–833.9875
A3
(5 MHz)
Not Valid
Valid
Cond. Valid
1201–1259
1260–1540
1541–1600
893.0125–893.7375
893.7500–897.2500
897.2625–898.0000
838.0125–838.7375
838.7500–842.2500
842.2625–843.0000
A2
(3 MHz)
Cond. Valid
Valid
Not Valid
801–859
860–980
981–1039
898.0125–898.7375
898.7500–900.2500
900.2625–900.9875
843.0125–843.7375
843.7500–845.2500
845.2625–845.9875
A
(10 MHz)
Not Valid
Valid
Not Valid
1–59
60–740
741–799
915.0125–915.7375
915.7500–924.2500
924.2625–924.9875
860.0125–860.7375
860.7500–869.2500
869.2625–869.9875
B Not specified Not specified Not specified Not specified
8
ARIB STD-T64-LPR-0 v1.0
-9-
4.3.2.3 Band Class 6 (2 GHz Band) 1
The Band Class 6 system designators for the CDMA equipment shall be as specified in Table 2
4-3-7 and Table 4-3-8. 3
4
Table 4-3-7 CDMA channel number to CDMA frequency assignment correspondence for Band 5
Class 6 6
Transmitter CDMA Channel NumberCenter Frequency for
CDMA Channel (MHz)
Mobile Station 0<N<1199 1920.000 + 0.050 N
Base Station 0<N<1199 2110.000 + 0.050 N
Channel numbers less than 1.25 MHz from the licensee’s band edge are not valid. 7
8
Table 4-3-8 CDMA channel numbers and corresponding frequencies for Band Class 6 and 9
Spreading Rate 1 10
Transmit Frequency Band (MHz) CDMA Channel Validity CDMA Channel Number
Mobile Station Base Station
Not Valid
Valid
Not Valid
0 – 24
25 – 1175
1176 – 1199
1920.000 – 1921.200
1921.250 – 1978.750
1978.800 – 1979.950
2110.000 – 2111.200
2111.250 – 2168.750
2168.800 – 2169.950
11
ARIB STD-T64-LPR-0 v1.0
-10-
Chapter 5 Output Power 1
2
Output power, Pout, of the repeater is the total mean power at maximum repeater gain 3
delivered to a load with resistance equal to the nominal load impedance of the transmitter. 4
Rated output power, PRAT, of the repeater is the total mean power level at maximum repeater 5
gain that the manufacturer has declared to be available at the antenna connector. 6
Antenna gain is the gain of the repeater antenna. Antenna gain does not include feeder loss. 7
5.1 Maximum Output Power 8
Maximum output power, Pmax, of the repeater is the total mean power level measured at the 9
antenna connector in specified reference condition. 10
11
5.1.1 Minimum Requirements 12
The requirements shall apply at maximum gain, with cdma2000 signals in the pass band of the 13
repeater, at levels that produce the maximum output power. 14
The rated output power shall not exceed the maximum level specified in Table 5-1. 15
16
Table 5-1 Rated output power limits 17
Directions Maximum Level
Uplink 16.0 dBm
Downlink 20.4 dBm
18
The repeater maximum output power shall remain within limits specified in Table 5-2 relative 19
to the manufacturer's rated output power. 20
21
Table 5-2 Repeater output power 22
Directions Limits
Uplink +0.79 dB and -3.0 dB
Downlink +2.0 dB and -4.0 dB
5.2 Maximum Antenna Gain 23
The antenna gain shall not exceed the limits specified in Table 5-3. 24
ARIB STD-T64-LPR-0 v1.0
-11-
Table 5-3 Antenna gain requirement 1
Antenna Gain Note
Uplink Tx 9 dBi or less
Downlink Tx 0 dBi or less If the antenna gain exceeds 0 dBi, the difference may be
compensated by reducing the maximum output power of downlink.
In the multiple antenna case, each antenna shall not exceed the above limits. 2
3
ARIB STD-T64-LPR-0 v1.0
-12-
Chapter 6 Frequency Error 1
2
Frequency error is a measure of difference between actual transmit frequency and the assigned 3
frequency. 4
6.1 Test Requirements 5
The frequency of the output signal shall be within the accuracy range given in Table 6-1. 6
7
Table 6-1 Frequency error test requirements 8
Directions Accuracy
Uplink ±300 Hz (Band Class 0, 3)
±150 Hz (Band Class 6)
Downlink ±0.05 ppm
9
ARIB STD-T64-LPR-0 v1.0
-13-
Chapter 7 Out of Band Gain 1
2
Out of band gain refers to the gain of the repeater outside the pass band. 3
7.1 Minimum Requirements 4
The gain of outside the pass band shall not exceed the maximum level specified in Table 7-1 5
where: 6
- f_offset is the distance from the edge frequency of the first or last 1.48 MHz channel within 7
the pass band. 8
9
Table 7-1 Out of band gain limits 10
Frequency Offset from the Edge Frequency, f_offset Maximum Gain
5 MHz 35 dB
10 MHz 20 dB
40 MHz 0 dB
11
ARIB STD-T64-LPR-0 v1.0
-14-
Chapter 8 Occupied Bandwidth 1
2
The occupied bandwidth is the width of a frequency band such that, below the lower and above 3
the upper frequency limits, the mean powers emitted are each equal to a specified percentage 4
β/2 of the total mean transmitted power. See also ITU-R Recommendation SM.328 [1]. The 5
value of β/2 shall be taken as 0.5%. 6
8.1 Minimum Requirement 7
The occupied channel bandwidth shall be less than 1.48 MHz based on a chip rate of 1.2288 8
Mcps. 9
10
ARIB STD-T64-LPR-0 v1.0
-15-
Chapter 9 Modulation Requirements 1
9.1 Waveform Quality 2
Waveform quality is measured by determining the normalized correlated power between the 3
actual waveform and the ideal waveform. This requirement ensures that the repeater does not 4
significantly contribute to the degradation of the CDMA waveform as measured by ρ. 5
6
9.1.1 Method of Measurement 7
Method of measurement is based on 3GPP2 C.S0051-0 [2]. 8
9
9.1.2 Test Requirement 10
The difference between the input signal ρ and the output signal ρ, in every case, shall not 11
exceed 0.025. 12
13
ARIB STD-T64-LPR-0 v1.0
-16-
Chapter 10 Transmitter Spurious Emission 1
2
Spurious emissions are emissions which are caused by unwanted transmitter effects such as 3
harmonics emission, parasitic emission, inter-modulation products and frequency conversion 4
products. This is measured at the repeaters RF output port. 5
Unless otherwise stated, all requirements are measured as mean power (RMS). 6
10.1 Uplink Spurious Emissions Requirements 7
8
10.1.1 Test requirements 9
At maximum repeater gain, with cdma2000 signal in the pass band of the repeater, at levels 10
that produce the maximum output power, the power of any spurious emission shall not exceed 11
the limits specified in Table 10-1 and Table 10-2. 12
13
Table 10-1 Band Class 0 and 3 Uplink spurious emissions requirements 14
Frequency Band l ∆f l Measurement
Bandwidth Test
Requirement Note
900 kHz ≤ l ∆f l <
1.98 MHz 30 kHz -42 dBc 815 MHz < f ≤ 850 MHz,
887 MHz < f ≤ 889 MHz,
893 MHz < f ≤ 901 MHz,
915 MHz < f ≤ 925 MHz 1.98 MHz ≤ l ∆f l 100 kHz -16 dBm
l ∆f l < 1.98 MHz 30 kHz -16 dBm 885 MHz < f ≤ 958 MHz
(excluding
887 MHz < f ≤ 889 MHz,
893 MHz < f ≤ 901 MHz,
915 MHz < f ≤ 925 MHz) 1.98 MHz ≤ l ∆f l 100 kHz -16 dBm
l ∆f l < 1.98 MHz 30 kHz -16 dBm f ≤ 885 MHz (excluding
815 MHz < f ≤ 850 MHz),
958 MHz < f (excluding
1884.5 MHz ≤ f ≤ 1919.6 MHz) 1.98 MHz ≤ l ∆f l 1 MHz -16 dBm
15
ARIB STD-T64-LPR-0 v1.0
-17-
Table 10-2 Band Class 6 Uplink spurious emissions requirements 1
l ∆f l Measurement
Bandwidth Test Requirement Note
1250 kHz < l ∆f l ≤ 1980 kHz
30 kHz
or
1.23MHz
-42 dBc
or
-54dBm
1980 kHz < l ∆f l ≤ 2250 kHz
30 kHz
or
1.23MHz
-50 dBc
or
-54 dBm
2250 kHz < l ∆f l ≤ 4 MHz 1 MHz - [13 + 1 x (l ∆f l - 2.25)] dBm Note-1
1 kHz -36 dBm
(9 kHz ≤ f < 150 kHz)
10 kHz -36 dBm
(150 kHz ≤ f < 30 MHz)
100 kHz -36 dBm
(30 MHz ≤ f < 1000 MHz)
4 MHz < l ∆f l
1 MHz -30 dBm
(1000 MHz ≤ f < 12.75 kHz) Note-2
Note-1: Unit of l ∆f l is MHz.
Note-2: excluding 1884.5 MHz ≤ f ≤ 1919.6 MHz
2
10.1.2 Protection of PHS 3
This requirement shall apply for the protection of PHS. The power of any spurious emission 4
shall not exceed the limits specified in Table 10-3 and Table 10-4. 5
6
Table 10-3 Band Class 0 and 3 Uplink spurious emissions requirement for PHS 7
Frequency Band Measurement Bandwidth Test Requirement Note
1884.5 MHz ≤ f ≤ 1919.6 MHz 1 MHz -26 dBm
8
Table 10-4 Band Class 6 Uplink spurious emissions requirement for PHS 9
Frequency Band Measurement Bandwidth Test Requirement Note
1884.5 MHz ≤ f ≤ 1919.6 MHz 300 kHz -51 dBm
10
ARIB STD-T64-LPR-0 v1.0
-18-
10.2 Downlink Spurious Emissions Requirements 1
2
10.2.1 Test requirements 3
At maximum repeater gain, with cdma2000 signal in the pass band of the repeater, at levels 4
that produce the maximum output power, the power of any spurious emission shall not exceed 5
the limits specified in Table 10-5 and Table 10-6. 6
7
Table 10-5 Band Class 0 and 3 Downlink spurious emissions requirements 8
Frequency Band l ∆f l Measurement
Bandwidth
Test
Requirement Note
750 kHz ≤ l ∆f l <
1.98 MHz 30 kHz -45 dBc 832 MHz < f ≤ 834 MHz,
838 MHz < f ≤ 846 MHz,
860 MHz < f ≤ 895 MHz 1.98 MHz ≤ l ∆f l 100 kHz -16 dBm
l ∆f l < 1.98 MHz 30 kHz -16 dBm 810 MHz < f ≤ 860 MHz
(excluding
832 MHz < f ≤ 834 MHz,
838 MHz < f ≤ 846 MHz) 1.98 MHz ≤ l ∆f l 100 kHz -16 dBm
f ≤ 810 MHz,
895 MHz < f (excluding
1884.5 MHz ≤ f ≤ 1919.6 MHz)
- 1 MHz -16 dBm
9
ARIB STD-T64-LPR-0 v1.0
-19-
Table 10-6 Band Class 6 Downlink spurious emissions requirements 1
l ∆f l Measurement
Bandwidth Test Requirement Note
885 kHz < l ∆f l ≤ 1250 kHz 30 kHz -45 dBc
1250 kHz < l ∆f l ≤ 1450 kHz 30 kHz -13 dBm
1450 kHz < l ∆f l ≤ 2250 kHz 30 kHz - [13 + 17 x (l ∆f l - 1.45)] dBm Note-1
2250 kHz < l ∆f l ≤ 4 MHz 1 MHz -13 dBm
1 kHz -13 dBm
(9 kHz ≤ f < 150 kHz)
10 kHz -13 dBm
(150 kHz ≤ f < 30 MHz)
100 kHz -13 dBm
(30 MHz ≤ f < 1000 MHz)
4 MHz < l ∆f l
1 MHz -13 dBm
(1000 MHz ≤ f < 12.75 kHz) Note-2
Note-1: Unit of l ∆f l is MHz.
Note-2: excluding 1884.5 MHz ≤ f ≤ 1919.6 MHz
2
3
10.2.2 Protection of PHS 4
This requirement shall apply for the protection of PHS. The power of any spurious emission 5
shall not exceed Table 10-7 and Table 10-8. 6
Table 10-7 Band Class 0 and 3 Downlink spurious emissions requirement for PHS 7
Frequency Band Measurement Bandwidth Test Requirement Note
1884.5 MHz ≤ f ≤ 1919.6 MHz 1 MHz -26 dBm
8
Table 10-8 Band Class 6 Downlink spurious emissions requirement for PHS 9
Frequency Band Measurement Bandwidth Test Requirement Note
1884.5 MHz ≤ f ≤ 1919.6 MHz 300 kHz -51 dBm
ARIB STD-T64-LPR-0 v1.0
-20-
Chapter 11 Receiver Spurious Emissions 1
2
The receiver spurious emissions power is the power of emissions generated or amplified in a 3
receiver that appear at the receiver antenna connector of the repeater. The requirements apply 4
to all repeaters with separate RX and TX antenna port. 5
For all cdma2000 repeaters equipped with common RX and TX antenna port, the transmitter 6
spurious emission requirements specified in Chapter 10 (Transmitter Spurious Emissions) is 7
valid. 8
11.1 Test Requirements 9
The power of any spurious emission shall not exceed the maximum level specified in Table 11-1 10
through Table 11-6. 11
12
Table 11-1 BC0 Downlink receiver spurious emission requirements 13
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
860.025 ≤ f ≤ 874.995 1 MHz - 81 dBm MS receiver band
815.025 ≤ f ≤ 829.995 1 MHz - 61 dBm MS transmitter band
Other 30 kHz - 54 dBm
14
Table 11-2 BC3 Downlink receiver spurious emission requirements 15
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
832.0125 ≤ f ≤ 833.9875
838.0125 ≤ f ≤ 843.0000
843.0125 ≤ f ≤ 845.9875
860.0125 ≤ f ≤ 869.9875
1 MHz - 81 dBm MS receiver band
887.0125 ≤ f ≤ 888.9875
893.0125 ≤ f ≤ 898.0000
898.0125 ≤ f ≤ 900.9875
915.0125 ≤ f ≤ 924.9875
1 MHz - 61 dBm MS transmitter band
Other 30 kHz - 54 dBm
16
ARIB STD-T64-LPR-0 v1.0
-21-
Table 11-3 BC6 Downlink receiver spurious emission requirements 1
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
2110 ≤ f ≤ 2170 1 MHz - 76 dBm MS receiver band
1920 ≤ f ≤ 1980 1 MHz - 61 dBm MS transmitter band
30 ≤ f < 1000 100 kHz - 57 dBm
1000 ≤ f ≤ 12750 1 MHz - 47 dBm MS receiver and transmitter
bands are excluded.
2
Table 11-4 BC0 Uplink receiver spurious emission requirements 3
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
860.025 ≤ f ≤ 874.995 30 kHz - 60 dBm BS transmitter band
815.025 ≤ f ≤ 829.995 30 kHz - 80 dBm BS receiver band
Other 30 kHz - 54 dBm
4
Table 11-5 BC3 Uplink receiver spurious emission requirements 5
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
832.0125 ≤ f ≤ 833.9875
838.0125 ≤ f ≤ 843.0000
843.0125 ≤ f ≤ 845.9875
860.0125 ≤ f ≤ 869.9875
30 kHz - 60 dBm BS transmitter band
887.0125 ≤ f ≤ 888.9875
893.0125 ≤ f ≤ 898.0000
898.0125 ≤ f ≤ 900.9875
915.0125 ≤ f ≤ 924.9875
30 kHz - 80 dBm BS receiver band
Other 30 kHz - 54 dBm
6
ARIB STD-T64-LPR-0 v1.0
-22-
Table 11-6 BC6 Uplink receiver spurious emission requirements 1
Frequency Band [MHz] Measurement Bandwidth Test Requirements Note
2110 ≤ f ≤ 2170 30 kHz - 60 dBm BS transmitter band
1920 ≤ f ≤ 1980 30 kHz - 80 dBm BS receiver band
30 ≤ f < 1000 100 kHz - 57 dBm
1000 ≤ f ≤ 12750 1 MHz - 47 dBm BS receiver and transmitter
bands are excluded
2
ARIB STD-T64-LPR-0 v1.0
-23-
Chapter 12 Requirements for a Blanket License Application 1
2
The cdma2000 repeater shall be equipped with one or more functions described in this Chapter 3
for a blanket license application: 4
5
a) Function to distinguish by the identification code 6
This function is to stop repeating if the identification code in radio waves from base station 7
is other operator's or other radio system's radio waves. 8
9
b) Function to periodically receive unique code 10
This function is to stop repeating if the unique code in radio waves from base station is 11
unable to receive periodically. 12
13
c) Function to be remotely controlled by base station 14
This function is to stop repeating by remote control from base station. 15
16
d) Other functions similar to above-mentioned three functions. 17
18
ARIB STD-T64-LPR-0 v1.0
-24-
Chapter 13 Requirements for Interference Avoidance to Other Radio Stations 1
2
The cdma2000 repeater shall be equipped with one or more techniques below: 3
4
a) ALC (Automatic Level Control) 5
ALC is the function to automatically keep the output power below the allowable maximum 6
level. 7
8
b) AGC (Automatic Gain Control) 9
AGC is the function to automatically control repeater gain to avoid the oscillation in case 10
antenna coupling loss is decreased. 11
12
c) Shutdown 13
Shutdown is the function to stop repeating in case the repeater emits distorted radio wave 14
due to oscillation. 15
16
ARIB STD-T64-LPR-0 v1.0
-25-
Chapter 14 Measurements 1
2 Measurements except for the Waveform Quality specified in Chapter 9 shall be conducted in 3
accordance with the following two measuring methods which are published by Telecom 4
Engineering Center Foundation (TELEC) unless otherwise directed in other notifications. 5
6
a) TELEC-T140 7
Measuring method for CDMA land mobile (repeater) stations 8
9
b) TELEC-T142 10
Measuring method for MC-CDMA/T-CDMA land mobile (repeater) stations 11
12
ARIB STD-T64-LPR-0 v1.0
-26-
Change History 1 2
3
Version Date History Ver. 1.0 March 18, 2009 Enacted by the 73rd ARIB Standard Assembly
ARIB STD-T64-LPR-0 v1.0
-27-
Change History List of Standards 1 2
No. Item No. Title Page Change Summary 1
2
3
1 2 3 4 5 6 7 8 9 10 11 12 13
THE LOW POWER REPEATERS FOR cdma2000 CELLULAR TELEPHONES
ARIB STANDARD ARIB STD-T64-LPR Version 1.0
Version 1.0 March 18, 2009
Published by
Association of Radio Industries and Businesses
11F, Nittochi Building, 1-4-1 Kasumigaseki, Chiyoda-ku, Tokyo 100-0013,Japan
TEL 03-5510-8590 FAX 03-3592-1103
Printed in Japan
All rights reserved
Distribution Price ¥xxxxx (including Japanese consumption tax)
top related