a: removal - ken-
Post on 03-Feb-2022
1 Views
Preview:
TRANSCRIPT
FU(STi)-14
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
3. Intake ManifoldA: REMOVAL1) Release the fuel pressure. <Ref. to FU(STi)-45,RELEASING OF FUEL PRESSURE, OPERA-TION, Fuel.>2) Open the fuel filler lid and remove the fuel fillercap.3) Disconnect the ground cable from battery.
4) Lift up the vehicle.5) Remove the under cover.6) Drain the engine coolant about 3.0 2 (3.2 US qt,2.6 Imp qt).
7) Remove the air cleaner upper cover and air in-take boot. <Ref. to IN(STi)-8, REMOVAL, AirCleaner.>8) Remove the air cleaner element.9) Remove the intercooler. <Ref. to IN(STi)-11,REMOVAL, Intercooler.>10) Remove the coolant filler tank. <Ref. toCO(H4DOTC)-32, REMOVAL, Coolant FillerTank.>11) Remove the power steering pump.
(1) Remove the front side V-belt.<Ref. to ME(STi)-41, REMOVAL, V-belt.>
(2) Disconnect the power steering switch con-nector.
(3) Remove the bolts which secure the powersteering pipe brackets to the intake manifold.
NOTE:Do not disconnect the power steering hose.
(4) Remove the bolts which secure the powersteering pump bracket.
(5) Remove the power steering tank from thebracket by pulling it upward.
FU-00009
FU-00016
FU-00017
FU-00018
FU-00019
FU-00020
FU(STi)-15
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
(6) Place the power steering pump on the rightside wheel apron.
12) Disconnect the emission hose (A) and connec-tor (B) from the PCV hose assembly.
13) Disconnect the engine coolant hoses from thethrottle body.
14) Disconnect the brake booster hose.
15) Disconnect the pressure hose from the intakeduct.
16) Disconnect the engine harness connectorsfrom the bulkhead harness connectors.
17) Disconnect the connectors from the enginecoolant temperature sensor (A), oil pressure switch(B) and crankshaft position sensor (C).
FU-00021
FU-01032
(A)(B)
FU-01074
FU-00023
FU-00024
FU-00025
FU-00026
(A)
(B)
(C)
FU-00027
FU(STi)-16
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
18) Disconnect the knock sensor connector.
19) Disconnect the connector from the camshaftposition sensor.
20) Disconnect the connector from the ignition coil.
21) Disconnect the engine harness fixed by clip (A)from the bracket.
22) Disconnect the fuel delivery hose, return hoseand evaporation hose.
CAUTION:• Do not spill fuel.• Catch fuel from hoses in a container or cloth.
23) Remove the bolts which secure the intake man-ifold to the cylinder heads.
24) Remove the intake manifold.
B: INSTALLATION1) Install the intake manifold onto cylinder heads.
NOTE:Always use new gaskets.
Tightening torque:25 N·m (2.5 kgf-m, 18.1 ft-lb)
FU-00028
FU-01038
FU-00030
FU-00031
(A)
FU-00032
FU-01039
FU-01039
FU(STi)-17
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
2) Connect the fuel delivery hose, return hose andevaporation hose.
3) Connect the connector to the oil pressure switch(B), crankshaft position sensor (C) and enginecoolant temperature sensor (A).
4) Connect the connector to the knock sensor.
5) Connect the connector to the camshaft positionsensor.
6) Connect the connector to the ignition coil.
7) Connect the engine harness with clip (A) to thebracket.
8) Connect the engine harness connector to thebulkhead harness connectors.
FU-00032
(A)
(B)
(C)
FU-00027
FU-00028
FU-01038
FU-00030
FU-00031
(A)
FU-00025
FU-00026
FU(STi)-18
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
9) Connect the brake booster vacuum hose.
10) Connect the engine coolant hoses to the throt-tle body.
11) Connect the emission hose (A) and connector(B) to the PCV hose assembly.
12) Connect the pressure hose to the intake duct.
13) Install the power steering pump.(1) Install the power steering tank on the brack-et.
(2) Connect the connector to the power steeringpump switch.
(3) Install the power steering pump, and tightenthe bolts.
Tightening torque:22 N·m (2.2 kgf-m, 15.9 ft-lb)
(4) Install the power steering pipe brackets onthe intake manifold RH.
FU-00023
FU-01074
FU-01032
(A)(B)
FU-00024
FU-00020
FU-00017
FU-00019
FU-00018
FU(STi)-19
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
(5) Install the front side V-belt.<Ref. to ME(STi)-41, INSTALLATION, V-belt.>
14) Install the coolant filler tank. <Ref. toCO(H4DOTC)-32, INSTALLATION, Coolant FillerTank.>15) Install the intercooler. <Ref. to IN(STi)-11, IN-STALLATION, Intercooler.>16) Install the air cleaner element.17) Install the air cleaner upper cover and air intakeduct as a unit. <Ref. to IN(STi)-8, INSTALLATION,Air Cleaner.>18) Connect the connector to the fuel pump relay.
19) Connect the battery ground cable to battery.20) Lift up the vehicle.21) Install the under cover.22) Fill the engine coolant. <Ref. to CO(H4DOTC)-17, FILLING OF ENGINE COOLANT, REPLACE-MENT, Engine Coolant.>
C: DISASSEMBLY1) Remove the fuel pipe protector RH.
2) Remove the engine ground terminal from the in-take manifold.
3) Disconnect the connector from the throttle posi-tion sensor (A) and manifold absolute pressuresensor (B).
4) Remove the throttle body from the intake mani-fold.
ME-00649
FU-01040
FU-01041
FU-01042
FU-01073
(A)
(B)
FU-01075
FU(STi)-20
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
5) Disconnect the connector from the fuel injector.
6) Disconnect the connector from the tumble gen-erator valve actuator.
7) Disconnect the connector from the tumble gen-erator valve sensor.
8) Disconnect the connector from the purge controlsolenoid valve.9) Remove the purge control solenoid valve.
10) Disconnect the evaporation hose and purgevalve from the intake manifold.
11) Remove the two bolts which hold the fuel pipeson the left side of intake manifold.
12) Remove the bolt which hold the fuel injectorpipe onto intake manifold.• LH SIDE
FU-01043
FU-00616
FU-00617
FU-01044
FU-01045
FU-00043
FU-01046
FU-01047
FU(STi)-21
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
• RH SIDE
13) Remove the harness bracket which holds theengine harness onto intake manifold.
14) Remove the engine harness from the intakemanifold.15) Loosen the clamp which holds the front left sidefuel hose to injector pipe, and then remove the pipefrom clamp.
16) Loosen the clamp which holds the right sidefuel hose to injector pipe, and then remove the pipefrom clamp.
17) Remove the bolts which install the fuel pipe onintake manifold.
18) Remove the fuel pipe assembly and pressureregulator from the intake manifold.19) Remove the intake duct from the intake mani-fold.
20) Remove the tumble generator valve assemblyfrom the intake manifold.
FU-01048
FU-01049
FU-00049
FU-01050
FU-01051
FU-01052
FU-01076
FU-00053
FU(STi)-22
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
D: ASSEMBLYNOTE:Replace the gasket with a new one.1) Install the tumble generator valve assembly tothe intake manifold.
Tightening torque:8.25 N·m (0.84 kgf-m, 6.1 ft-lb)
2) Install the air intake duct to the intake manifold.
Tightening torque:19 N·m (1.94 kgf-m, 13.7 ft-lb)
3) Install the fuel pipe assembly and pressure reg-ulator to the intake manifold.
Tightening torque:4.9 N·m (0.5 kgf-m, 3.6 ft-lb)
4) Install the fuel injector pipe LH.
5) Connect the left side fuel hose to injector pipe,and tighten the clamp screw.
6) Install the fuel injector pipe RH.7) Connect the right side fuel hose to injector pipe,and tighten the clamp screw.
8) Install the engine harness to the intake manifold.9) Install the harness bracket which holds the en-gine harness onto intake manifold.
Tightening torque:19 N·m (1.94 kgf-m, 13.7 ft-lb)
FU-00053
FU-01076
FU-01052
FU-01050
FU-01051
FU-00049
FU(STi)-23
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
10) Tighten the bolts which install the fuel injectorpipe onto intake manifold.
Tightening torque:19 N·m (1.94 kgf-m, 13.7 ft-lb)
• LH SIDE
• RH SIDE
11) Tighten the two bolts which install the fuel pipeson the left side of intake manifold.
Tightening torque:4.9 N·m (0.5 kgf-m, 3.6 ft-lb)
12) Connect the evaporation hoses to the purgevalve.
NOTE:Connect the evaporation hoses as shown in the fig-ure.
13) Connect the evaporation hose and purge valveto the intake manifold.
FU-01046
FU-01047
FU-01048
FU-01049
(A) To intake duct
(B) To intake manifold
(C) To purge control solenoid valve
(D) To fuel pipe ASSY
FU-00043
FU-01057
(A)
(B)
(D)
(C)
FU-01045
FU(STi)-24
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
14) Install the purge control solenoid valve.
Tightening torque:16 N·m (1.6 kgf-m, 11.8 ft-lb)
15) Connect the hoses to the purge control sole-noid valve.
NOTE:Connect the evaporation hoses as shown in the fig-ure.
16) Connect the connector to the purge control so-lenoid valve.17) Connect the connector to the tumble generatorvalve sensor.
18) Connect the connector to the tumble generatorvalve actuator.
19) Connect the connector to the fuel injector.
20) Install the throttle body to the intake manifold.
NOTE:Replace the gasket with a new one.
Tightening torque:8 N·m (0.8 kgf-m, 5.8 ft-lb)
(A) To purge valve
(B) To intake manifold
FU-01044
(A)
(B) FU-00054
FU-00617
FU-00616
FU-01043
FU-01075
FU(STi)-25
FUEL INJECTION (FUEL SYSTEMS)INTAKE MANIFOLD
21) Connect the connector to the throttle positionsensor (A) and manifold absolute pressure sensor(B).
22) Install the engine ground terminal to the intakemanifold.
Tightening torque:19 N·m (1.94 kgf-m, 13.7 ft-lb)
23) Install the fuel pipe protector RH.
Tightening torque:19 N·m (1.94 kgf-m, 13.7 ft-lb)
E: INSPECTIONMake sure the fuel pipe and fuel hoses are notcracked and the connections are tightened.
FU-01073
(A)
(B)
FU-01041
FU-01042
FU-01040
top related