399800 b ams-8923 connection diagram...ams-8923 connection diagram 399800, rev b a, initial release...

AMS-8923 Connection Diagram

399800, Rev B A, Initial Release - May, 20101, Custom Design - August, 2007 B, Revised Release - April, 2017Revision / Date: ets-lindgren.com ets-lindgren.com

Note: ETS-Lindgren may substitute a similar part with the same functionality for another part.

Warranty Informationeht ees ,noitamrofni ytnarraw roF Product Information Bulletin.

Product Information Bulletin

:gniwollof eht rof tnempihs ruoy htiw dedulcninergdniL-STEeht eeS Product Information Bulletin

Warranty informationSafety, regulatory, and other product marking informationSteps to receive your shipmentSteps to return a component for serviceETS-Lindgren calibration serviceETS-Lindgren contact information

© Copyright 2007-2017 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copiedby any means without written permission from ETS-Lindgren Inc.

The logo is a registered trademark of ETS-Lindgren Inc.ETS-Lindgren

USA Headquarters1301 Arrow Point DriveCedar Park, TX 78613Phone: +1.512.531.6400

Please see ets-lindgren.com for a list of all ETS-Lindgren offices.

WARRANTY

.tnempihs ruoy htiw dedulcnieht ees ,noitamrofni ytefas lanoitidda roF Product Information Bulletin

Safety Information

Laser Danger: Denotes a laser (IEC Class 3B) is part of the operating system of the device. Laser powerrange is 5-500 mW.

Visible laser radiation: Avoid exposure to beam. Do not stare into beam or view directly with optical instruments.

Left Side

Right Side

RightTop

RightBottom

Control Box (part# 114760)•

EMCenter Modular RF PlatformTM•TEST INSTRUM ENT

Test Instrumentation(required units provided by customer)

•

•AMS-8923 installed in finished chamber(part# 114700) • Interconnect Kit (part# 115018)

Laser Control(part# 115017)

Sensor Position Display(part# 115014)

Laser Cable(part# 665080)

4-Conductor Cable (part# 660046)(part# 660047)8-Conductor Cable

(part# 705344-10)Fiber Optic Cable (part# 106043-10m)BNC Cable

• 10-Meter Fiber Optic Cable(part# 705344-10)

Additional cables(as required by configuration)

HIGH VOLTAGE: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injuryor death.

CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void yourwarranty if you attempt to service the unit by yourself, disconnect all electrical power before starting. There are voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained servicepersonnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source.

BEFORE POWER IS APPLIED TO THIS INSTRUMENT, GROUND IT PROPERLY through the protective conductor of the AC power cable to a power source provided with protective earth contact. Any interruption of the protective (grounding) conductor, inside or outside the instrument, or disconnection of the protective earth terminal could result in personal injury.

These components are required to connect the AMS-8923 Measurement System:

+105

+90

+75

+60

+45

+30

+15

0

PHI

-15

-30

-45

-60

-75

-90

-105

-120

PHI

THETA

+105

+90

+75

+60

+45

+30

+15

0

THETA

-15

-30

-45

-60

-75

-90

-105

-120

-135

-150

-165

+165

+150

+135

+120

PHI

-135

-150

-165

+165

+150

+135

+120

THETA

RF PORTS

100/240 VAC50/60 Hz

100 VA M AX

HI G H VO LTAG E

WARNI NG

AMS–8923 Controller Box Part #114760

LASER LASERSWITCH DISPLAY

THETA PHIDEDICATED PATHS SWITCHED

PATH

TRIGGEROUTPUT

™

Laser On

Power On EMCenter

Interlock

Standby

OFF

ON

ALIGNM ENT LASERS

part#705344-10

part# 660047

part# 660046AMS-8923 Connection Diagram

ets-lindgren.com

Before connecting any components, see on the back page of this document.Safety Information

part# 665080

Theta switch assembly

Phi switch assembly

Controller Box - Right Side, Bottom

Controller Box - Left Side

Controller Box - Right Side, Top

Connect Phi and Thetaswitch assemblies

from each sensor toappropriate connectors

on Controller Box

+105

+90

+75

+60

+45

+30

+15

0

PHI

THETA

+105

+90

+75

+60

+45

+30

+15

0

+105

+90

+75

+60

+45

+30

+15

0

PHI

-15

-30

-45

-60

-75

-90

-105

-120

PHI

THETA

+105

+90

+75

+60

+45

+30

+15

0

THETA

-15

-30

-45

-60

-75

-90

-105

-120

-135

-150

-165

+165

+150

+135

+120

PHI

-135

-150

-165

+165

+150

+135

+120

THETA

RF PORTS

LASERSWITCH

DISPLAY

100/240 VAC50/60 Hz

100 VA M AX

HI G H VO LTAG E

WARNI NG

AMS–8923 Controller Box Part #114760

LASER

TRIGGEROUTPUT

part# 660046

part# 660047 Filter

RF PORTS

THETA PHI

SWITCHEDPATH

DEDICATED PATHS

LASER

part# 705344-10

OUT

IN

TEST INSTRUM ENT

TEST INSTRUM ENT

Equipment Rack

EMCenter

part# 106043-10m

LASERSWITCH DISPLAY

THETA PHIDEDICATED PATHS SWITCHED

PATH

OFF

ON

ALIGNM ENT LASERS

EMControl7006-001

TM

EMControl7006-001

TM

1 2AUXILIARY

DEVICE 1OUT

DEVICE 2IN OUT

IN

1 2AUXILIARY

DEVICE 1IN OUT

DEVICE 2IN OUT