1 mark gleeson gleesoma@cs.tcd.ie (01) 896 2666 distributed systems group, trinity college, dublin...

Mark Gleesongleesoma@cs.tcd.ie

(01) 896 2666

Distributed Systems Group,Trinity College, Dublin

14.02.2009

Diploma in Health Informatics Networks

Objectives

• Understand some network terminology- enough to be able to read further on the topic.

• Understand some issues of network design.

• Issues concerning application of networking to health.

• Emphasis on practical aspects

Introduction to Networks

1. Introduction

2. Network characteristics

3. Network Software

4. Network Hardware

5. Security

6. Internet and the World Wide Web

7. Telemedicine

Section 1 – Introduction - Network Basics• What is a network?

• What does it do?

• How useful is the network

• Various key attributes

Introduction (1/2)

• In the 20th Century key technologies were employed for information gathering, processing and distribution.

• Some developments include– worldwide telephone networks– the invention of television and radio– the unprecedented growth of the computer

industry– launching of communication satellites

• These areas are converging. The convergence of computers and communications is very significant.

Introduction (2/2)

• Initially computers were highly centralized, usually within a single room. Computers were physically large.

• The development and advances made in the computer industry are huge.

• Now – lots of small independent computers communicating to do a job. These are called Computer Networks

What is a Computer Network? (1/2)• An interconnected collection of

computers which are:– Co-operative

• Co-operative action is required between the components

– Autonomous• All components are capable of independent

action• Any resource is capable of refusing requests

– Mutually Suspicious• Components verify requests

What is a Computer Network? (2/2)• Any computer connected to a network

is known as a host.– Local host

• Your own computer

– Remote host• The computer elsewhere you are in contact

• There are hardware and software aspects to computer networks

(Digital) Bandwidth

• The amount of data per second a communications link can carry

• Typically referred to in bits per second– Note 1 byte == 8 bits

• The actual amount of useful data you can send will be less than the actual capacity– Overheads for

• Addressing• Routing• Error detection• Medium access

Latency / Delay

• Measure of the delay from sending a piece of data or request until it is processed at the destination– Exceptionally important for

• Video and audio– Voice over IP, Skype, Video conferencing

• Interactive systems– Inquiry based systems – patent records – Booking systems

• Needs careful investigation to determine the weak points– Is it the network or the computer?

More Terminology

• Attenuation– Measure of how much a signal degrades per

distance in a certain medium• Different cable types have difference values• Attenuation limits the distance you can

communicate over

• Electro Magnetic Interference - EMI– Electrical noise artificially generated

• Watch out for high powered electrical equipment– MRI machines, Trams, Electric trains, Microwaves

• Of particular concern in wireless networks– Microwaves operate at a frequency used by 802.11b/g

Section 2 - Network characteristics• What Are Networks

• Network Types and Topologies

• Communication concepts

• Basic Message Types

What are Networks?

• Tanenbaum’s definition:"A network is an interconnected collection of autonomous computers"

TCP/IP

Types of Networks

• Bus-based networks– Original Ethernet (802.3)

• Star-based networks– Switched (Modern) Ethernet (802.3ab)

• Ring-based networks– FDDI– Token Ring (802.5)

• Wireless networks– WiFi (802.11a/b/g/n), Bluetooth,

Hyperlan IrDA, WiMax, GSM, EDGE,3G

LAN Topologies

Bus architecture (Ethernet) Ring architecture (Token Ring)

Star architecture (switched Ethernet)

FDDI Ring

Double ring architecture (FDDI)

Types of Networks

• Classification based on diameter:1 m System

10 m Room

100 m Building

1 km Campus

10 km City

100 km Country

1,000 km Continent

10,000 km Planet

Multi-processor

LAN (Local Area Networks)

MAN (Metropolitan Area Networks)

WAN (Wide Area Networks)

The Internet

PAN (Personal Area Networks)

Local-Area Networks (LANs)

* Figure is courtesy of B. Forouzan

Wide-Area Networks (WANs)

• Latency• Administration/Jurisdiction

Simplex

Duplex

Half-Duplex

Full-Duplex

Point-to-Point & Multipoint

Basic Message Types

• Three basic message types– 1. Unicast - one sender to one receiver

Sender

Receiver

Basic Message Types

• Three basic message types– 1. Unicast - one sender and one receiver– 2. Broadcast - one sender, everybody

receives

• Broadcast addresses:– network ID +– all bits of host ID set– e.g. 134.226.255.255

Sender

• Three basic message types– Unicast - one sender and one receive– Broadcast - one sender, everybody

receives– Multicast - one sender and a group of

receivers

Basic Message Types

Sender

Receivers

Section 3 - Network Software

• Originally hardware matters were the main focus when building networks the software was an afterthought.

• Key Network Software concepts:– Layers– Protocols– Interfaces– Services

Layers

• The idea of introducing layers of software reduces the design complexity. It divides the large problem into smaller ones.

• The number, name, contents and function of each layer vary from network to network.

• However for each network the idea is that one layer offers something to a second layer without the second layer knowing how the first layer is implemented.

Protocols

• Provided two networks adhere to the same set of layers layer n on one machine can (virtually)communicate with layer n on another machine.

• The rules and conventions used in this conversation are known as the layer n protocol.

• A protocol is an agreement between the communicating parties as to how the communication proceeds.

Interfaces

• Interfaces exist between adjacent layers.• The interface specifies what one layer is

offering to the other layer.• Analogous to Object-Oriented concept of

Encapsulation • One of the most important aspects of

designing the network software is to provide clean, well understood interfaces. Minimise the amount of information that has to be passed from layer to layer.

• Once a layer’s interface is defined many implementations of that layer can exist. The only stipulation is that the interface is adhered to.

Design Issues for the layers

• Addressing – identifying senders and receivers.

• Data transfer rules- Simplex, half duplex, Full duplex.

• Error control - Agree on a protocol. Implementation of the protocol.

• Order of the messages

• Fast sender swamping a slow receiver - feedback or an agreed size is required.

• Length of messages - Too large/too small.

• Multiplexing - use the channel for multiple unrelated conversations.

• Multiple routes - How to choose the route. Physical and logical choices.

Reference Models

• Two reference models are considered– The OSI (Open Systems Interconnection)

Reference Model –initiated in the 1970s matured in the late 1980s and early 1990s

– TCP/IP initiated through work carried out in the late 1960s, matured and adopted in early 1990s

Open Systems Interconnetion Model

• Developed by the International Standards Organisation (ISO)

• The model deals with connecting open systems i.e. systems that are open for communication with other systems.

Application

Presentation

Session

Transport

Network

Datalink

Physical

Application

Presentation

Session

Transport

Network

Datalink

Physical

Medium

Principles used to arrive at the Seven Layer Architecture• A layer should be created where a

different level of abstraction is needed.• Each layer should perform a well

defined function• Standardisation issues.• Minimise data that has to travel

between the layers• Large enough number of layers to

support distinct functionality but not too large a number to create an unwieldy architecture

Network Protocols

• Common “language” on the network• Define network components’ interactions

– Actions/requests– Responses

• Defined in standards– ISO Standards– IEEE Standards (mainly at physical and

mac)– ITU Recommendations– IETF Request For Comments (RFC)

The TCP/IP Reference model

• The grandparent of all computer networks the Arpanet – research network sponsored by the Department of Defence (DoD) in America.

• The network used leased lines to connect government offices and universities together. When satellite and radio networks appeared there were problems. The thinking for TCP/IP began. TCP/IP is named after its two primary protocols.– TCP- Transmission Control Protocol– IP- Internet Protocol

• A layered architecture used to connect multiple networks together in a seamless way was one of the design goals from the very beginning

• Connections should remain intact even if there was some subnet damage.

The Physical Layer

• The Physical Layer is the lowest layer and is concerned with wiring and electrical standards. The design issues have to do with making sure that when a sender sends a 1 bit that the receiver receives a 1 bit and not a 0 bit.

• Example issues to be agreed when building this layer– How many volts to represent a 1– How many volts to represent a 0– How many microseconds a bit lasts.– Does transmission proceed simultaneously in both

directions– How are connections established and torn down– How many pins are on connectors and what each pin

does.– What kind of transmission medium, wired, fiber optic

Communication between End-Systems

Data Link Layer

Duties of the Data Link Layer

The data link layer is responsible for transmitting frames from one node to the next on the same network.

Packetizing & Addressing

• Packetizing: Encapsulating data in frame or cell i.e. adding header and trailer

• Addressing: Determining the address of the next hop (LANs) or the virtual circuit address (WANs)

Error Control & Flow Control

• Error Control: Detect errors in received data and attempt to correct them– Error Detection– Error Correction

• Flow Control: Prevent the sender from overwhelming the receiver– Go-back-N– Sliding Window

Medium Access Control

• Control the access to a shared medium to prevent conflicts and collisions– Aloha– CSMA/CD or CSMA/CA

Analogy: Point-to-Point Communication• Simple Synchronization

Alice Bob

Phone conversation

Analogy: Shared Medium

• Synchronisation is more complex

Asynchronous Systems

• Round robin– Good if many stations have data to

transmit over extended period• Reservation

– Good for stream traffic e.g audio, video• Contention

– Good for bursty traffic– All stations contend for time– Distributed– Simple to implement– Efficient under moderate load– Tend to collapse under heavy load

Multiple-Access Protocols

LAN Technologies - Ethernet

• Developed by Metcalfe 1972/3 while at Xerox PARC

• Standards in 1978, 1995, 1998

• Types of Ethernet– Original Ethernet– Switched Ethernet– Fast Ethernet– Gigabit Ethernet

• Medium Access Control– CSMA/CD

• IEEE 802.2: Logical Link Control

Metcalfe’s Ethernet sketch

LAN Technologies - Evolution of Ethernet

• 1972/73 defined for coaxial cable• Fast Ethernet used mainly unshielded

twisted pair (UTP)• Gigabit Ethernet now common in desktops

and laptops• 10GB Ethernet used mainly for backbone

802.3 MAC Frame

• 64-bit frame preamble (10101010) used to synchronize reception – 7 bit preamble (10101010) + 1 start flag

(10101011)• Maximum frame length: 1518 bytes

max 1500 bytes payload• Minimum frame length: 64 bytes

min 46 bytes payload* Figure is courtesy of B. Forouzan

Ethernet Addresses – The ‘MAC’ Address• A unique 48 bit long number

– Eg 00:A0:4A:21:19:13

• Types of Addresses:– Unicast – delivered to one station– Multicast – delivered to a set of stations

• 01-80-C2-00-00-00 Spanning tree (for bridges)

• 03-00-00-00-00-01 NETBIOS

– Broadcast – delivered to all stations• FF-FF-FF-FF-FF-FF

vendor-specific

Non-bridged and Bridged Networks

• Extension of Networks: – Repeaters, Hubs - Physical Layer – Bridges, Switches - Data Link Layer– Routers - Network Layer

• Collision domains: – Collision affects all machines in one segment* Figure is courtesy of B.

Forouzan

Switched Ethernet

• Switch delivers packets to individual machines– Without affecting communication with

other machines• Collisions only occur on individual links

Full-duplex Switched Ethernet

• No collisions– One line to send– One line to transmit

Comms Rooms

Switches in Comms Rooms

Wireless (1/2)

• IEEE 802.11 standard of 1997 started the revolution with 2Mbps top speed– Now on 802.11g with 54Mbps– 802.11n to promise 150+Mbps– Referred by some as Wireless Ethernet– Shares significant similarities with original bus

style Ethernet• Reliability and Performance much less than

wired network– Current max speed 54Mbps shared by all on same

base station– Prone to interference and poor reception– Speed drops under poor conditions to reduce

errors– Range 100m+ in open much less in office situation

Wireless (2/2)

• Star like network– Your laptop talks to a ‘access point’ which

connects to your wired network– Laptop which move been access points to keep

the strongest signal• Uses the Industrial, Medical and Scientific

Band– No licence needed– Healthcare staff should be aware this shared

use and verify before installation that there won’t be a conflict

• Advantages– No need to install ethernet cabling everywhere– Network access everywhere in range

The Network Layer

• The Network Layer is concerned with controlling the operation of the subnet. A key design issue is determining how packets are routed from source to destination. They can be static, dynamic.

• Example issues to be agreed when building this layer– Routing mechanisms– How is subnet congestion to be dealt with– How are costings included- national

boundaries– Addressing mechanisms.– In broadcast networks the network layer

may be very thin or non-existent.

Position of the Network Layer

• Sends frames through data link layer• Accepts data from transport layer

Duties of Network Layer

• Problems the Network Layer needs to address:– Transfer over networks of various architectures– Addressing on a “global” scale– Adjusting to maximum transmission units

• Hop-to-hop delivery provided by data link layer• Transfer of packets between end systems

provided by network layer

Switching in the Internet

• Connection-oriented communication– Connection exists between sender and receiver

for duration of communication• Connection-less communication

– Data between sender and receiver

The Scenario

• Computer A establishes IP address of Computer B• Computer A creates IP packet with address of

Computer B as destination and its own IP address as source

• Routers are responsible to direct packet towards destination

Computer A Computer B

The Scenario

• Best route: Smallest number of hops?

The Scenario

• Best route: – Fastest round-trip time?– Highest Bandwidth?

Routing Basics

• Routing Tables– Creating tables

• Dynamic vs. Static

– Maintaining tables• Periodic vs. Aperiodic

Computer A Computer Bnode1

Structure of the Internet

• Autonomous Systems– e.g. Companies, ISPs, 3rd-level

Institutions

Autonomous Systems

• Stub network– Network that does not forward to other

network• Transit network

– Network that forwards traffic between other networks

• Point-to-point link

Stub NetworkTransit

Network Point-to-Point

Yet another Layer ?!?

• Transport Layer – TCP • Why should you care?• Applications use TCP as main

communication mechanism– HTTP– Remote procedure calls (RPC)

• File Transfer

Network Layer vs Transport Layer

Network Layer Transport Layer

• Communication between two nodes

• Communication between processes

• Best effort delivery • Ordered, guaranteed delivery

• Connection-less communication

• Connection-oriented communication

Transport Layer

• Process-to-Process Delivery

IP Addresses & Port Numbers

• IP Addresses determine the host

• Port Numbers determine the application

Communication at Transport Layer• Comms at

Transport Layer from port to port

• IP implementation multiplexes depending on protocol field in IP header

Client-Server Paradigm

Server

Client A

Client B

Problems

• Connection establishment• Connection termination• Ordered Delivery• Retransmission strategy• Duplication detection• Crash recovery• Flow control

Section 4 - Network Hardware

• Connecting hosts and networks require hardware devices which include..

• Networking and Internetworking Devices– Repeaters– Bridges– Hubs– Switches– Routers– Gateways– Brouters

• Modems• Transmission Media

Networking and Internetworking Devices• These devices can be divided into 3

categories – Repeaters, – Bridges, – Routers and Gateways.

• Repeaters and Bridges are used at the Networking of hosts

• Routers and Gateways are used for Internetworking

Repeaters and Bridges

• Repeaters– Operate at the physical layer. They

regenerate signals.

• Bridges– Operate at the physical and data link

layers.– They are used to divide a network into

segments and can control traffic flow and are useful for securing the network.

– They can also regenerate signals.

What is a Switch

• A layer 2 device – Data Link Layer• Builds a table of the MAC addresses of

devices attached on each port• ‘Store and Forward’

– Switch receives a packet– Verifies it is error free– Looks at its destination MAC– Sends the packet on

• ‘Cut Through’– Starts to forward packet once it reads the

destination address– No error checking

• Improved performance

Photo thanks to Cisco Systems

What is a Router

• A layer 3 device – – Works at physical, data link and network layers

e.g. Internet Protocol (IP) level– Is a bridge between a number of distinct

networks• Example your internal network and the internet beyond

• Range from simple devices• ADSL router for home users

– To• Extremely complex enterprise level

• Looks at the destination of each IP packet and determines where it would be sent on for its next hop– Tries to select the best route

Other Devices

• Hubs – A central device that acts like a

multiport repeater– Date mainly from the time of non

switched ethernet

• Brouters– A single or multiprotocol router that

sometimes acts as a bridge and sometimes as a router

Connecting Devices and the OSI Model

ADSL – Modem for the 21st Century• Normal telephone lines support only a

subset of the frequencies found in human speech– This limits the available bandwidth– ADSL uses part of this untapped bandwidth– Download bandwidth typically greater than

upload, hence the A for Asynchronous• Suits the needs of the consumer market• Business users may wish to get equal

– Quite vulnerable to noise• Limits on your distance from exchange

– Further away the slower the available speed

• Combined with VPN a true work from home solution

Transmission Media

• Transmission Media Characteristics– Bandwidth– Response Time for a request

• Transmission Media Types– Twisted Pair– Coaxial cable- – Fiber Optics– Wireless Media – Radio, Microwaves,

Infrared, Lightwave

Twisted Pair

• The wire consists of two insulated copper wires about a mm thick, normally 24 gauge solid core copper.

• The purpose of twisting the wires is to reduce electrical interference. (two parallel wires would act as an antenna). Various categories of cable

• Many twisted pair cables can be bundled together, typically 4 pairs

• They can be used for analog and digital transmission.

• The bandwidth depends on the thickness of the wire and the distance travelled.

• Shielded Twisted Pair (STP) and Unshielded Twisted Pair(UTP)

Twisted-Pair Cable

Effect of Noise on Parallel Lines

The McGraw-Hill Companies, Inc., 1998

Noise on Twisted-Pair Lines

Unshielded Twisted-Pair Cable (UTP)• Most common type of cable used in

computer networks• 8 wires forming 4 pairs• Different qualities

– Cat 3 – for 10Mbps– Cat 5 - for 100Mbps– Cat 5e – for 1Gbps

• Most common in current use– Cat 6 – better for 1Gbps may allow 10Gbps

• Best to future proof to avoid pain later• Cables of different types look identical

– Cable type is printed on the side

Shielded Twisted-Pair Cable

Fiber Optics

• An optical transmission system has three components– The light source– The transmission medium – The detector.

• A pulse of light indicates a 1, lack of light indicates a 0.

• The transmission medium is a unidirectional ultra thin fibre of glass or plastic

• The aim is to get the angle of incidence of the light at such a point to make the light refract back into the medium. In the case of a fibre optic cable this means the light is trapped within the cable.

• At the centre of the cable is the glass/plastic core which is surrounded by a glass cladding and then a plastic coating.

Transmission Media Performance

Medium Cost Speed Attenuation EMI Security

UTP Low 1-100Mbps High High Low

STP Moderate 1Mbps-1Gbps High Moderate Low

Coax Moderate 1Mbps-1Gbps Moderate Moderate Low

Optical Fibre

High 10Mbps-10Gbps Low Low High

Radio Moderate 1-54Mbps Low-High High Low

Microwave High 1Mbps- 10Gbps Variable High Moderate

Satellite High 1Mbps- 10Gbps Variable High Moderate

Cellular High 9.6-19.2Kbps Low Moderate Low

Scan TypeNumber of Exams per

day Total (MB)General Radiographs 200 9600Ultrasound 20 60Doppler Ultrasound 30 90Bariums 5 400ERCP's 5 400CT 12 1800MRI 10 1500Nuclear Medicine 10 30Cardiac Angios 10 8000

Daily Totals 302 21,880Yearly Totals 78,520 5,688,800

Example Sizes of Medical Images

• Network Users– Developers– Administration staff (software and hardware)– End users (specialised users, general public)

• Uses of Networks– Resource Sharing- locally or over

considerable distance.– High Reliability- multiple CPUs, replication of

files.– Saving money- Price of PCs compared to

mainframes.

• Scalable solutions- The network can grow as the needs do

• Communication medium- supporting team work

• Accessing remote information- banking, health issues, hobbies, shopping

• Person to person communication- e-mail, instant messaging, video conference

• Interactive entertainment- films, games, live shows.

Uses of Networks in Healthcare?

• Communicating into/out of and between hospitals

• Paging Staff• Networking instrumentation• Maintenance of instrumentation• To aid communication

– Professional to professional. – Professional to patient. – Patient to patient.

• Sharing Information of all types

Network and Distributed Systems

• There is some confusion over these two terms.– Hardware is required for both to operate

• The distinction is in the software.– In a distributed system the existence of the

autonomous computers is transparent. – The system is concerned with doing a job and

not with how the connections are established and managed.

• A distributed system refers to software built on top of a network.

• With a network the user needs to explicitly deal with the network in terms of logging on, deciding which computer to use and managing the network.

Section 6 - Security

• Security Issues

• Virtual Private Networks

• Issues with wireless networks

• Methods of attack

• Risks

Security Issues

• Secrecy– Keeping information out of the hands of

unauthorised users.

• Authentication– Making sure you are talking to the right

person.

• Data Integrity control– Making sure the data is correct.

• Security effects each layer in the network design.

No Network Is Secure

• Original Ethernet– Every host on the bus could see and capture

every transmission made• Trivial to recover passwords, web pages you viewed

• The physical network itself cannot be considered to be secure– Wires can be tapped

• Wireless communications available to all within range with a suitable receiver

• Need to trade off the strength of security with the practicality of the measures– Users when faced with a complex process may

attempt to undermine the system• Sharing of passwords or not logging out

Wireless Networks

• Extremely vulnerable to attack– Anyone with a suitable radio can listen

• IEEE 802.11 originally used a 40 bit WEP key– Shared encryption key by all users of the

network– Later versions supported a 104 bit key– Proved to be very easy to crack in both

versions• WiFi Protected Access (WPA/WPA2)

– Based on 802.11i standard– EAP extensible Authentication Protocol

» Authentication framework not a protocol» Can integrate with existing authentication systems» 802.1x

• Best practice in Network Management is to heavily restrict access to external users or to block it totally– Avoid potential security issues– Protect from hackers

• What of legitimate users– People who work at other locations– Particularly relevant concerns in the

Healthcare Domain

VPN – Virtual Private Network

• Not strictly a security solution• Two implementations

– Connecting you to a remote network– A network within a network

• Allows you to access resources on another network as if you where connected directly

• A secure encrypted tunnel between your computer and others on the same network

• Typically requires a dedicated ‘VPN box’ on the office end network to provide the service

VPN - Connecting you to a remote network

• Ideal for a single user– Work from home, on the road, other

institution• User needs VPN client software

– Setup can be complex for users– Need to implicitly log in to access the

network• Not transparent

– Potential security risk if users computer is breeched• Hacker may have access into network

Methods of Attack (1/3)

• Impersonation– Using someone else’s password or a terminal that

is already logged on.• Active wire-tapping

– Connecting a device(authorised/unauthorised) to a communication link to obtain access to data through the generation of false messages.

• Passive wire-tapping– Monitoring data coming over a communication link.

• Traffic flow analysis– Analysing the frequency of data traffic, seeing

which data is encrypted and which is not.• Eavesdropping

– interception of information

• Replay– Play back a recording of a communication

• Routing Table modification – Sending messages to the wrong address or multiple

addresses.• Audit Trail Information Modification

– To cover up an attack.• Operational Staff Table Modification

– To change access rights.• Bogus Frame insert

– Inserting bogus information as a frame.• Data Portion Modification

– Modify the data portion of a message.• Viruses

• Sequencing Information Modification – Change the order of the pieces of information.

• Message Deletion – Removing the message completely

• Protocol Control Information modification – To send data to a different location.

• Misuse of resources – Swamping communication lines – Denial of service

• Interruption of power supply – Denial of service

• Malicious physical damage – Denial of service

• Theft– Parts of computers or entire computers could be stolen.

Confidentiality issues arise.

Disposal of computer hardware

• You typically contract a third party to securely shred paperwork, but you skip a used computer.– Computer can store a virtually unlimited amount of

data in a easy to search format• Serious privacy issues concerning medical

records• Computer may have no confidential information

but!– Usernames, passwords, security certificates and so

on for networked information may be stored on the computer, thus allowing access

• Essential the contents of the hard disk be wiped not just deleted– Most operating systems have the ability to do this– Or remove hard drive and use a sledgehammer

Section 6 - The Internet and the World Wide Web

• Addressing and Domain Names

• Who is in charge

• Relationship between IP address and hostnames

• Arrangements for .ie domains

Internet Addressing and Domain Names• To be able to identify a host on the internetwork,

each host is assigned an address– Internet Protocol address.

• Addresses are assigned in a delegated manner.• The Internet Corporation for Assigned Names and

Numbers (ICANN) has responsibility for Internet Protocol (IP) address space allocation

• What is ICANN?• As a private-public partnership, ICANN is dedicated

to– preserving the operational stability of the Internet; – to promoting competition; – to achieving broad representation of global Internet

communities– to developing policy appropriate to its mission

through bottom-up, consensus-based processes.

Internet Addressing and Domain Names• ICANN are the top body. They comprise IANA

http://www.iana.org/• Users are assigned IP addresses by Internet service

providers (ISPs). ISPs obtain allocations of IP addresses from a local Internet registry (LIR) or national Internet registry (NIR), or from their appropriate Regional Internet Registry (RIR):

• APNIC (Asia Pacific Network Information Centre) - Asia/Pacific Region

• ARIN (American Registry for Internet Numbers) - North America and Sub-Sahara Africa

• LACNIC (Regional Latin-American and Caribbean IP Address Registry) – Latin America and some Caribbean Islands

• RIPE NCC (Réseaux IP Européens) - Europe, the Middle East, Central Asia, and African countries located north of the equator

Internet Addressing and Domain Names• The .org domain is operated by Public Interest

Registry. It is intended to serve the noncommercial community, but all are eligible to register within .org.

• The .com domain is intended to serve the commercial community.

• The .gov domain is reserved exclusively for the United States Government. It is operated by the US General Services Administration.

• The .edu domain is reserved for postsecondary institutions accredited by an agency on the U.S. Department of Education's list of Nationally Recognized Accrediting Agencies and is registered only through Educause.

• The .net domain is reserved for networks; usually reserved for organizations such as Internet service providers

IP and Internet Addressing

• Currently there are two types of Internet Protocol (IP) addresses in active use: – IP version 4 (IPv4) and IP version 6 (IPv6).

• IPv4 was initially deployed on 1 January 1983 and is still the most commonly used version.

• IPv4 addresses are 32-bit numbers often expressed as 4 octets in "dotted decimal" notation (for example, 192.0.32.67). Can cater for 4.4 billion addresses

• Deployment of the IPv6 protocol began in 1999. IPv6 addresses are 128-bit numbers and are conventionally expressed using hexadecimal strings (for example, 1080:0:0:0:8:800:200C:417A).

IP Addresses

• 32-bit number in IPv4– 4,294,967,296 addresses

• IP addresses are unique and universal– with some exceptions

• Dotted decimal notation:– Bytes of binary notation represented as

decimal separated by dot• Internet hosts have both IP addresses

and hostnames– wilde.cs.tcd.ie == 134.226.32.55

Sending IP datagrams over Ethernet• When the network layer wishes to send

data across the data link layer• IP address needs to be mapped to an

ethernet address

Ethernet card

IP Implement.

Card driver

AA.BB.CC.00.00.11

172.16.1.1

Mapping Domain Names

– Hostname - wilde.cs.tcd.ie– Internet Address - 134.226.32.55

• How does a machine translate a fully qualified hostname into an IP address?

• It consults its nearest Domain Name Server (DNS)

• The local Nameserver knows the mappings for local machines and – At least one root nameserver which knows

all nameservers for the top level domains.

.ie domains

• All registrations handled by the IE Domain Registry - www.iedr.ie– Was based in UCD until 2000, now a

independent non profit making body– You are required to prove a connection

to the domain name sought

• 10th Feb 2008 – Total number of domains 118,515

• In Jan 1995– Total domains 347

Growth in .ie domains

Section 7 – Telemedicine

• What is it?

Definitions

• Telemedicine is the rapid access to shared and remote medical expertise by means of telecommunications and information technologies, no matter where the patient or the relevant information is located. (CEC 1993)

• Telemedicine has been defined in General Terms as “Medicine practiced at a distance” and as such, it encompasses both diagnosis and treatment, as well as medical education. (Journal of Telemedicine and Telecare, 1995)

Definitions

• Telemedicine is the delivery of healthcare services, where distance is a critical factor, by all healthcare professionals using information and communications technologies for the exchange of valid information for diagnosis, treatment and prevention of disease and injuries, research and evaluation, and for the continuing education of healthcare providers, all in the interests of advancing the health of individuals and their communities. (World Health Organisation 1998)

Telemedicine

• Many different definitions of Telemedicine. Be aware of this.

• Telemedicine is a process not a technology. Can be applied to many different domains.

• Can be used for patient/clinician, patient/patient, clinician/clinician communication.

• Can be used to support training• As with all applications of technology,

appropriateness is the key. The application should be clinically driven.

Definition

• The WHO offers a holistic definition of telemedicine: “The delivery of healthcare services, where distance is a critical factor, by all healthcare professionals using information and communication technologies for the exchange of valid information for diagnosis, treatment and prevention of disease and injuries, research and evaluation, and for the continuing education of healthcare providers, all in the interests of advancing the health of individuals and their communities” (WHO 2004)

• Telecare, a term often associated with telemedicine, can be defined as: "...the use of information and communication systems to give patients with or without their healthcare professional or informal carer access to information sources wherever they are located… frequently…within patients' place of residence” NHS (2004)

Characteristics of Telemedicine systems• Interaction style- Real Time, Store and

Forward.• Data types- Text, Images, Sound, Video• Equipment • Action – Direct Intervention, Advice• Patient numbers – one patient, multiple

patients• Duration

Some Advantages and Obstacles of Telemedicine• Advantages

– Improved use of resources

– Continuing professional development

– Reduces unnecessary patient transfers

– Facilitates homecare for the elderly and the chronically ill

– Equitable access to care!– Links doctors with

remote centres of excellence

– Wireless links can be used in cases of lack of infrastructure

• Obstacles– Patient and

professional dissatisfaction in some specialities

– Lack of standards– Security issues– Legal and ethical

implications– Equipment failure– Lack of protocols of

care for these new types of interactions.

History

• Pre-electronic telemedicine– Accounts from the middle ages of a physician

examining a patient for plague- the patient and the physician were on opposite sides of the river.

– Prescribing by post was practised well before national postal systems were in place.

• Electronic telemedicine– Telegraphy- equipment was developed to send an X-

ray– Telephony- voice communication, computer networks– Radio- initially by morse code and later by voice.– Television- closed circuit television, video

conferencing– Wireless communication- use of mobile phone

technologies and satellites.

Research

• Why is Telemedicine not in widespread use?

• The technologies exist but the organisational and personal problems exist.

• Lots of funding has been allocated and has been spent on projects analysing, testing and evaluating technical requirements.

• More projects/research should be funded to show cost-effectiveness and evaluation of new Telemedicine applications.

Ethical and Legal Issues

• Some projects in Europe have looked at certain aspects of this area (SEISMED, ISHTAR, TrustHealth and SIREN). They have mainly been concerned with the security and confidentiality.

• More work needs to be done to research other aspects including accountability, responsibility, licensure, reimbursement, intellectual property rights, changes in consultation and referral patterns, defining the ‘owner of patients’, defining geographical catchment areas.

Economics/Evaluation

• Need to compare the new technology with an alternative way of working. What is the system costing at the moment?

• How to asses the cost of the new technology- equipment, software, installation, training, maintenance, legal, utilisation rates.

• How do we asses the benefits- people getting well, shorter stays in hospital, less time spent with the expert, patient not having to travel, expertise experienced by the remote healthcare professional.

• Methods are required if economic evaluation is to take place. Care should be taken when comparing costs across, domains, environments and time.

Practice

• Teleradiology• Telepathology• Teledermatology• Telecardiology• Telepsychiatry• Teleorthopaedics• Surgical Consultations• TeleENT• Tele-EEG• Minor Injuries

• Mobile Telemedicine

• Maritime Telemedicine

• Teleopthamology• Home Care• Telephone Services• Education• Telesurgery

Using Networks to Provide Equality of Care?• Network Infrastructures- Network

hardware and network software• Network users• Software applications• Legislation• Standards• Delivering care (need experts on site)

Network Infrastructure

• In order to avail of networked healthcare a network infrastructure must be in place.

• This infrastructure requires an initial investment, maintenance investment and investment to keep it up to date

• It is hard to see therefore even at the technology end how equality of care can be achieved.

Network Users

• In various countries, regions and hospitals different levels of technical skill exist.

• If we assume that all places have the same network infrastructure it still doesn’t allow us achieve equality of care

Software applications

• On top of the network infrastructure software applications.

• Depending on economics, skill and awareness of users differences can exist.

• Not everyone will be aware of the software applications that exist and the implications of choosing particular software e.g. from standards point of view

Legislation

• Be aware that using networks allows the user to bypass physical boundaries thus enabling a specialist in Ireland to communicate with a patient in England. There are legal implications to this that haven’t been addressed.

• Equality of care may not be possible due to these legalities. The closer you live to the specialist the better.

Standards

• In order to have healthcare delivered to all areas standards are required.

• Communication standards• Coding standards e.g. for diagnosing,

prescribing.• Data set format standards• Semantic standards• If all areas do not agree to the

standards then equality of care is not possible.

Experts on site

• Even if all the infrastructure, software applications, standards, legislation and skills are equal is it possible to get equality of care?

• Remember healthcare is ultimately delivered by human experts.

• Technology can only be used to support the current processes of healthcare delivery or to make new processes possible.

• Telemedicine Information Exchange (US)

• http://tie.telemed.org/• Covers:

– Extensive bibliography (>14,000 entries)

– Projects– Events calendar– Funding sources– News

1 mark gleeson gleesoma@cs.tcd.ie (01) 896 2666 distributed systems group, trinity college, dublin...

Documents

it networks - lecture 1 mark gleeson gleesoma@csd.ie (01)...

university of dublin trinity college department of computer...

note de lansare pentru debian gnu/linux 5.0 (lenny), arm ·...

via iv novembre,34 sospiro giugno 2016.pdf1 dist....

1 it networks - lecture 1 mark gleeson gleesoma@tcd.ie 16th...

carol o’sullivan robert mooney...

1 mark gleeson gleesoma@tcd.ie distributed systems group,...

1 trinity college dublin n4c technical kick-off tcd slides...

http:// 1 an approach to real-time support in ad hoc...

application of the golden ratio to 3d facial models ·...

some security and privacy issues in the 21st...

clusters of re-used keys - cryptology eprint archive1...

1 it networks - lecture 2 mark gleeson gleesoma@cs.tcd.ie...

return and volatility of prices and sentiments khurshid...

vivio50 © 2004 jones@cs.tcd.ie - 1 19/11/04 tock tick -...

carol o’sullivan - carnegie mellon school of...

mevrouw erna delchambre - uitvaart vanwynsberghe...erna...

2009 (14.02.2009 a1_z_soruları)

learning agents: introduction - trinity college...

a brief survey of multimedia annotation localisation on the...