1. loto procedure · procedure, stop & contact your supervisor * loto procedure # a-xxxxxxx...
Post on 22-Jul-2020
18 Views
Preview:
TRANSCRIPT
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Band saw
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical End of cord Plastic clamshell and padlock
Stop machine, unplug cord, and install clamshell, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Bench Grinder
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical End of cord Plastic clamshell and padlock
Stop machine, unplug cord, and install clamshell, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Buffing wheel
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip the breaker switch and install plastic breaker adaptor, lock and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Disc Sander (Busy Bee)
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical End of cord Plastic clamshell and padlock
Stop machine, unplug cord, and install clamshell, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
2
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Disc Sander (General Mfg. Co. Ltd)
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip the breaker switch and install plastic breaker adaptor, lock and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
3
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Down Draft Table
Equipment Location: ED/ID
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE, NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Drill Press
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Horizontal Belt Sander
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
2
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Hot Wire Cutter
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical End of cord Plastic clamshell and padlock
Stop machine, unplug cord, and install clamshell, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Milling Machine
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Scroll Saw
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks: 1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Spindle Sander
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Strip Heater
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical End of cord Plastic clamshell and padlock
Stop machine, unplug cord, and install clamshell, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Table saw
Equipment Location: ED/ID Studio
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
Approved by: Date:
2
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Vacuum and Heating Table
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip the breaker switch and install plastic breaker adaptor, lock and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
1
1. LOTO Procedure
LOCKOUT TAGOUT PROCEDURE
Equipment
Identification
Equipment Name/Description: Wood Lathe
Equipment Location: ED/ID Studio Room 517
Total # of Energy Isolation Devices/locks:
1
NOTICE BEFORE SERVICING THIS MACHINE , NOTIFY AFFECTED PERSONNEL. ONLY PROPERLY TRAINED AND AUTHORIZED PERSONNEL SHALL PERFORM LOCKOUT TAGOUT PROCEDURE
Energy Source
Location Type of EID/lock to be used
Steps for locking & tagging
Verification Procedure
Electrical Breaker box
Plastic breaker adaptor
Stop machine, flip breaker switch and install plastic breaker adaptor, lock, and tag.
Attempt to start machine, visually confirm it will not start.
IF SYSTEM CANNOT BE LOCKED OUT OR IF SYSTEM FAILS VERIFICATION PROCEDURE, STOP & CONTACT YOUR SUPERVISOR
*LOTO Procedure # A-xxxxxxx Revision #:
2
Approved by: Date:
top related