ALPU-ALVR

ApplicationsWireless Broadband Networks

• WiMAX

• WiFi

• MESH

• Wireless Backhaul

The ALPU-ALVR is purpose built for Alvarion WiMAX and WiFi Ethernet radios and meets the new UL 497 standards. ALPU-ALVR is the premier primary and secondary protector for your high-speed packet network equipment from lightning and other transients. It is the only Alvarion UL 497 listed protector for primary protection. The ALPU-ALVR has low capacitance/impedance and insertion loss so that your packets will reach their destination without disruption from your surge protection system. The ALPU-ALVR is configured with three types of surge protection: silicon diodes for over-voltage, fuses for power line cross, and PTC (positive temperature coefficient) fuses for sneak current.

UL 497 Listed - Primary - Advanced Lightning Protection Unit for 55V WiMAX & Power Over Ethernet Applications

208.772.8515 800.882.9110 FAX 208.762.613310701 N. Airport Road, Hayden, ID 83835

www.transtector.com sales@transtector.comAn ISO 9001:2000 and 14001 Certified Company

ALPU-ALVRConfigurations

Features•  Surge Protection - over voltage,      sneak current and fault current•  Minimal capacitance/low     impedance •   Purpose-built for Alvarion broad-      band wireless equipment •  100 percent, non-degrading silicon     suppression•  Appropriate for primary and      secondary protection

WarrantyFive (5) year unconditional warrantyTen (10) year manufacturer’s warranty

1453-036 Rev. A

Installation

DataService VoltageCable Entry/Exit

Part Number

Voltage Protection Level

Response Time (Max.)

Operating Temperature<5 Nanoseconds

-40° to +80°C

2 Ethernet

55VDC

2

1101-640

130Vpk @ 150A 10/1000μs152Vpk @ 1500A 8/20μs

Max. Cont. Operating 90VDC

Max. Cont. Current 1 AMP

Alvarion Radio Models BreezeMax

BreezeAccess

BreezeNet

This product is available through Transtector distributors Anixter, Hutton, Tessco and WinnCom.

Remove the cover by loosening the four captive cover screws using a Phillips screwdriver. Mount the ALPU-ALVR as close to the equipment to be protected as possible using the provided hardware and the concealed mounting holes. Mount the unit in the orientation shown.

Thread a multiconductor cable from the data source through the strain relief adjacent to the marking on the PCB labeled “Input.”

Strip back the cable jacket as needed, then install the conductors into the IDC connectors labeled “Input” - place the wires into the grooves in the connector, leaving approximately 1/8” of wire overhanging, and press down firmly with the punch-down tool until the wires firmly engage into the fork terminals.

Repeat this procedure for the outgoing multiconductor cable, using the connectors labeled “Output.

Tighten the strain reliefs to secure the cables (DO NOT OVER TORQUE!). Replace the cover.

Dimensions:6.5”h X 4.7”w X 2.6”d13.9 cm X 12.1 cm X 6.6 cm

UL 497 ListedPrimary Surge Protector

CONCEALEDMOUNTING HOLES

EXTERNAL GND LUGACCEPTS 4-14 AWG

STRAIN RELIEF ACCEPTSCABLE DIA. RANGE0.250" THRU 0.375"

+ D A TA D C +-D A TA D C ++ D A TA D C --D A TA D C -D C 4 TX +D C 5 TX -D C 7 R X +D C 8 R X -

TE R M IN A L / P O ST D E SC R IP T IO N12345678

D C 2 (-)D C 2 (-)D C 2 (-)D C 2 (-)D C 2 (-)D C 2 (-)D C 2 (-)D C 2 (-)

TA B LE 1IN P U T/O U TP U T W IR IN G U S IN G ID C TE R M IN A L STR IP S