alphaeclipse roadstar multiple slave sign … roadstar multiple slave sign ... 2006 alphaeclipse...
TRANSCRIPT
READ ME FIRSTAlphaEclipse RoadStar
MULTIPLE SLAVE Sign Connection
http://www.adaptivedisplays.com/support/eclipseThis QuickStart gives a brief overview of sign installation.For complete instructions, see the “Instructions for the Sign Installer” manual (pn 9717-5021).
Identify the MASTER sign and each SLAVE sign. Locate the label on the back of each sign:
Starting with the sign with SERIAL ADDRESS = 1, locate and open the Control Cube’s right door:
Remove the communication cable from the sign: There are three, labeled communication cables:
Up to 3 SLAVE signs
Each sign (except for the last sign) will have a wiring kit in the Control Cube.
The Control Cube is on the right side in the bottom row.
Use the 5/32-inch hex tool to open the two door locks.
5/32-inch hex tool
Red BlackSHIELD
March 20, 2006 1175631001
© Copyright 2006 Adaptive Micro Systems LLC. All rights reserved.Adaptive Micro Systems • 7840 North 86th Street • Milwaukee, WI 53224 USA • 414-357-2020 • 414-357-2029 (fax) • http://www.adaptivedisplays.comTrademarked names appear throughout this document. Rather than list the names and entities that own the trademarks or insert a trademark symbol with each mention of the trademarked name, the publisher states that it is using names for editorial purposes and to the benefit of the trademark owner with no intention of improperly using the trademark.The following are trademarks of Adaptive Micro Systems: Adaptive, Alpha, AlphaLert, AlphaNET, AlphaNet plus, AlphaEclipse, AlphaEclipse RoadStar, AlphaEclipse StreetSmart, AlphaPremiere, AlphaTicker, AlphaVision, AlphaVision InfoTracker, AlphaXpress, Automode, BetaBrite, BetaBrite Director, BetaBrite Messaging Software, Big Dot, Director, EZ KEY II, EZ95, PagerNET, PPD, PrintPak, Serial Clock, Smart Alec, Solar, TimeNet. The distinctive trade dress of this product is a trademark claimed by Adaptive Micro Systems LLC.Due to continuing product innovation, specifications in this manual are subject to change without notice.
Run the three communication cables through one of the conduit openings under the controller board:
Repeat steps #2 through #5, until all the signs are connected as shown below:
Complete the sign installation.• See the “Instructions for the Sign Installer” manual (pn 9717-5021).
• Remember to earth ground the sign using the ground lug on the back of the sign.
Communication conduit holes• Run communication cables
through one of these three conduit holes.
• Do NOT run communication cables in the same conduit as the power wires.
Power wire conduit hole
Controller board
COM2
Connect communication cables to these (see step #6). COM0
COM3
MASTER UNITSERIAL ADDRESS = 1
SLAVE UNITSERIAL ADDRESS = 2
Control cube(bottom rightmost cube)
To COM 2 in next sign. To COM 0 in next sign. To COM 3 in next sign.
Control cube(bottom rightmost cube)
5
Controller board(bottom)
1 2 3 4 5 1 2 3 41 2 3 4 5 6 7
COM 0
5
Controller board(bottom)
1 2 3 4 5 1 2 3 41 2 3 4 5 6 7
COM 0
COM 3
COM 3
SHIELDBLACKRED
SHIELDBLACKRED
SHIELDBLACKRED
SLAVE UNITSERIAL ADDRESS = 3
Communication Cable Conduit:• Run the three communication cables through a conduit.• Do NOT run communication cables in the
same conduit as the power wires. • Cable that is not run through a conduit will deteriorate from exposure to sunlight.
CONNECT TOCOM 0 (MAIN RS485)IN ADDRESS 2
SHIELDBLACKRED
SHIELDBLACKRED
CONNECT TOCOM 3 (SYNC COM)IN ADDRESS 2
CONNECT TOCOM 0 (MAIN RS485)IN ADDRESS 3
SHIELDBLACKRED
CONNECT TOCOM 3 (SYNC COM)IN ADDRESS 3
SHIELDBLACKRED
SHIELDBLACKRED
CONNECT TOCOM 2 (TEMP PROBE)IN ADDRESS 3
1 2 3 4 5 6 7COM 2
Temperature probe (optional)Mount the probe to a light-colored surface at least 6 feetabove ground and not in direct sunlight.
1 2 3 4 5 6 7
SHIELD
COM 2
BLACKRED
BLACKRED
SHIELD
GREENWHITE
CONNECT TOCOM 2 (TEMP PROBE)IN ADDRESS 2
Ground lug
March 20, 2006 AlphaEclipse RoadStar Multiple Slave Sign Connection QuickStart (pn 1175631001)