air handling unit - salda
TRANSCRIPT
WWW.SALDA.LT
AIR HANDLING UNIT CONNCECTION VIA TL-WR802N
(AHU, TL-WR802N, smartphone)
QUICK LAUNCH GUIDE
CONTENTS
I. CONNECTING THE ROUTER 3II. TP-LINK WIRELESS N NANO ROUTER RANGE EXTENDER MODE CONFIGURATION VIA WIRELESS 3II.I. QUICK INSTALLATION GUIDE 6III. TP-LINK WIRELESS N NANO ROUTER ACCESS POINT MODE CON-FIGURATION VIA WIRELESS 21III.I. QUICK INSTALLATION GUIDE 24
The company reserves the right to make changes of technical data without prior notice 3
There are two types of router configurations:
1. TP-LINK Wireless N Nano router Range extender mode configuration via wireless TL-WR802N is used to extend the range of wireless signal of the exist-ing AP or wireless router. On this mode, the wired port LAN/WAN works as LAN. MB-GATEWAY could connect to the control device by wireless way.
2. TP-LINK Wireless N Nano router Access point mode configuration via wire-less As the supplement of wired LAN, TL-WR802N enables the wired LAN to connect to the MB-GATEWAY wirelessly. Connect TL-WR802N to the power and connect the LAN cable correctly with MB-GATEWAY, you can access MB-GATE-WAY by your PC(s), Mobile phone, Tabled and etc, to the router wirelessly. On this mode, the wired port LAN/WAN works as LAN. The Pre-encryption function is opened by default and the default password is the last unique eight numbers of each Router’s MAC address.
I. CONNECTING THE ROUTER
MB-GATEWAY
The root AP�sWi-Fi name
TP-LINK router
MB-Gateway
TL-WR802N�sWi-Fi name:
TP-LINK_XXXX
�
A
Internet
Root router
Root AP
B
II. TP-LINK WIRELESS N NANO ROUTER RANGE EX-TENDER MODE CONFIGURATION VIA WIRELESS
1. Connect the router according to steps A to C in the diagram. Connect the LAN/WAN port of TL-WR802N to the wired network port with an Ethernet cable to MB-GATEWAY and connect TL-WR802N to the power.
Figure 1.1 Hardware Installation of the TL-WR802N in Range Extender Mode
The company reserves the right to make changes of technical data without prior notice4
Figure 2.1 Wi-Fi Info card
LAPTOPS
Figure 2.2 Wi-Fi connection
Enter the Security key from Wi-Fi Info card Figure 2.1. Click Next Figure 2.3.
Figure 2.3 Security key window
Click the icon at the bottom of your desktop. Click refresh button, and then select the default SSID of the Router. Click Connect Figure 2.2.
1. 2. Wait until the router boots up, about 30 second, then use the default Wi-Fi Name
and Password printed on the Wi-Fi Info card to connect to the router Figure 2.1.
The company reserves the right to make changes of technical data without prior notice 5
MOBILE PHONES, TABLETS
Go to Wi-Fi settings. Click the button Scan and then select the default SSID of the Router. Figure 2.4.
Figure 2.4 Wi-Fi connection
Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Connect. Figure 2.5.
Figure 2.5 Security key window
The company reserves the right to make changes of technical data without prior notice6
Figure 1.1 Login window
admin
admin
Figure 2.1 Quick Setup
With a Web-based utility, it is easy to configure and manage the TL-WR802N 300Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Mac-intosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the default address http://tplinkwifi.net in the address field of the browser. After a moment, a login window will appear, similar to the one in Figure 1.1. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
2. After a successful login, you can click the Quick Setup menu to quickly configure your Router.
3. Click Next, and then Working Mode page will appear (figure 2.1) and choose Range Extender Mode and click Next on Working Mode page (Figure 3.1).
II.I. QUICK INSTALLATION GUIDE
The company reserves the right to make changes of technical data without prior notice 7
Figure 3.1 Working Mode page
4. AP list page will appear as shown in Figure 4.1. Find the SSID of the Access Point you want to access, and select the Choose checkbox in the corresponding row. For example, the first item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown in the Figure 4.1.
Figure 4.1 AP List
The company reserves the right to make changes of technical data without prior notice8
Figure 5.1 Quick Setup - Wireless
• Wireless Name of Root AP – The SSID of AP that you want to access. • MAC Address of Root AP – The MAC address of AP that you want to access.• WDS Mode – In WDS Repeater mode, the AP with WDS enabled will transfer data
to an associated root AP. AP function is enabled meanwhile. The wireless repeater transfers signal between its stations and the root AP for greater wireless range. En-ter the MAC address of the root AP in the field ‘MAC Address of Root AP’.
• Wireless Security Mode – This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type.
• Root AP Wireless Password – If the AP your router is going to connect need pass-word, you need to fill the password in this blank .
• Wireles name of Range Extender – Select same like roo ap name.
NOTE: If you know the SSID of a desired AP, you can also enter it into the SSID field manually.
5. Wireless Setting page will appear. Enter the ROOT AP Wireless password and select radio button ‘Copy from Root AP’, then click Next as shown in Figure
The company reserves the right to make changes of technical data without prior notice 9
6. On this page you can configure the IP parameters of the LAN. If you are not famil-iar with the setting on this page, it is strongly recommended to keep the provided default values, otherwise wireless network performance may be poor. When you have finished, click the button Next, as it is shown in Figure 6.1.
Figure 6.1 Quick Setup – Network Settings
7. You will then see the Finish page. Figure 7.1. To finnish configuration click Reboot.
Figure 7.1 Quick Setup - Finish
The company reserves the right to make changes of technical data without prior notice10
NOTE: The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For the best results, the place your Router should be placed:
• Near the center of the area in which your wireless stations will operate.• In an elevated location such as a high shelf. • Away from the potential sources of interference, such as PCs, microwaves, and
cordless phones.• Away from large metal surfaces. Failure to follow these guidelines can result in
significant performance degradation or inability to wirelessly connect to the Router.After reboot connect the LAN/WAN port of TL-WR802N (A in Figure 8.1) to the wired network port with an Ethernet cable to MB-GATEWAY (B in Figure 8.1) and connect MB-GATEWAY to ventialtion system (C in Figure 8.1).
Figure 8.1 Hardware Installation of the TL-WR802N and MB-GATEWAY in Range Extender Mode
LAPTOPS
Click the icon at the bottom of your desktop. Click refresh button, and then select SSID of the Router, which you write enter in Wireless Name of Range Extender field. Figure 5.1. Click Connect like in figure 9.1.
Figure 9.1 Wi-Fi connection
MB-GATEWAY
The root AP�sWi-Fi name
TP-LINK routerMB-Gateway
TL-WR802N�sWi-Fi name:
TP-LINK_XXXX
B
A
Internet
Root router
Root AP
C
8. Select new access point.
The company reserves the right to make changes of technical data without prior notice 11
Enter the Security key, which you write in Root AP Wireless Password field in figure 5.1. Click Next.
Figure 9.2 Security key window
MOBILE PHONES, TABLETS
Go to Wi-Fi settings. Click button Scan and then select SSID of the Router, which you entered in Wireless Name of Range Extender field. Figure 5.1.
Figure 9.3 Wi-Fi connection
Enter the Security key in Root AP Wireless Password field. Figure 5.1.Click Connect in Figure 9.4
Figure 9.4. Security key window
The company reserves the right to make changes of technical data without prior notice12
Figure 10.1 Google play store application
In the search results list find the application SALDA AIR. Click on the application. Figure 10.2
Figure 10.2 SALDA AIR application
9. To access MB-GATEWAY, open a web-browser (Google Chrome is recommend-ed) in address field type the MB-GATEWAY device name (hostname). According to the factory settings (default) MB-GATEWAY device name MBGW - plus the last six MAC address characters, for example: mbgw900154. In the page enter the login data: according to the preset parameters (default) username: admin password: admin.
10. Control MB-GATEWAY via SALDA AIR android application.
Install SALDA AIR to mobile phone.Go to Google play store. In the Search field enter SALDA AIR.
The company reserves the right to make changes of technical data without prior notice 13
Click the button INSTALL. Figure 10.3
Figure 10.3 Install SALDA AIR application window.
In the window that appears click ACCEPT and SALDA AIR will be installed on your device. Figure 10.4
Figure 10.4 Install SALDA AIR application window
The company reserves the right to make changes of technical data without prior notice14
Wireless configuration.
Figure 11.1 Security key window
Enter the Security key in the field Root AP Wireless Password. Figure 5.1. Click Con-nect. Figure 11.2.
Figure 11.2. Security key window
Go to Wi-Fi settings. Click button scan, then select SSID of the Router and enter it in the field Wireless Name of Range Extender. Figure 5.1.
11. Start AIR SALDA
The company reserves the right to make changes of technical data without prior notice 15
Start SALDA AIR on Android and CONNECTING window will appear, as shown in Fig-ure 11.3.
Figure 11.3. Connecting window
In the CONNECTING window click the button AUTODISCOVER. Figure 11.3. SALDA AIR will find MB-GATEWAY as shown in Figure 11.4.
Figure 11.4 Autodiscover
Figure 11.5. SALDA AIR
After this you can controll MB-Gateway via SALDA AIR, as shown in figure 11.5.
The company reserves the right to make changes of technical data without prior notice16
12. Control MB-GATEWAY via SALDA AIR IOS application.
Install SALDA AIR to mobile phoneFirst go to App store in search input write SALDA AIR.
Figure 12.1 App store
The company reserves the right to make changes of technical data without prior notice 17
In search list find SALDA AIR application. Click GET 12.2
Figure 12.2 SALDA AIR application
Click INSTALL button in figure 12.3.
Figure 12.3 Install SALDA AIR application window.
The company reserves the right to make changes of technical data without prior notice18
13. Start AIR SALDA on IOS
Configurate wirelessGo to wifi settings. Click scan button and then select SSID of the Router, which you write in Wireless Name of Range Extender field in figure 5.1.
Figure 13.1 Security key window
The company reserves the right to make changes of technical data without prior notice 19
Enter the Security key, wich you write in Root AP Wireless Password field in figure 5.1. Click Connect figure 13.2.
Figure 13.2 Security key window
Start SALDA AIR on iOS and CONNECTING window will appear, as shown in Figure 13.3.
Figure 13.3 Connecting window
The company reserves the right to make changes of technical data without prior notice20
In the CONNECTING window click the button AUTODISCOVER. Figure 13.3. SALDA AIR will find MB-GATEWAY as shown in Figure 13.4.
Figure 13.4 Autodiscover
Figure 13.5 SALDA AIR
After this you can controll MB-Gateway via SALDA AIR in figure 13.5.
The company reserves the right to make changes of technical data without prior notice 21
1. Connect the router following the steps according to steps A– to C in the diagram. Connect the LAN/WAN port of TL-WR802N to the wired network port with an Eth-ernet cable to MB-GATEWAY and connect TL-WR802N to the power.
III. TP-LINK WIRELESS N NANO ROUTER ACCESS POINT MODE CONFIGURATION VIA WIRELESS
Figure 1-1 Hardware Installation of the TL-WR802N in AP Mode
2. Wait for about 30 seconds until the router boots up, then connect to the router using the default Wi-Fi Name and Password printed on the Wi-Fi Info card. Figure 2.1.
Figure 2-1 Wi-Fi Info card
MB-GATEWAY
TP-LINK router
MB-Gateway
TL-WR802N�sWi-Fi name:
TP-LINK_XXXX
C
A
B
The company reserves the right to make changes of technical data without prior notice22
LAPTOPS
Click the icon at the bottom of your desktop. Click refresh button, and then select the default SSID of the Router. Click Connect Figure 2.2.
Figure 2.2 Wi-Fi connection
Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Next. Figure 2.3
Figure 2.3 Security key window
The company reserves the right to make changes of technical data without prior notice 23
MOBILE PHONES, TABLETS
Go to Wi-Fi settings. Click the button Scan and then select the default SSID of the Router Figure 2.4.
Figure 2.4 Wi-Fi connection
Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Connect. Figure 2.5.
Figure 2.5 Security key window
The company reserves the right to make changes of technical data without prior notice24
Figure 1.1 Login window
After a moment, a login window will appear, similar to the one in Figure 1.1. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 2-1 Quick Setup
admin
admin
With a Web-based utility, it is easy to configure and manage the TL-WR802N 300Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Mac-intosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and enter the default ad-dress http://tplinkwifi.net in the address field of the browser.
III.I. QUICK INSTALLATION GUIDE
2. After a successful login, you can click the Quick Setup menu to quickly configure your Router.
The company reserves the right to make changes of technical data without prior notice 25
3. Click Next, and then Working Mode page will appear as shown in Figure 3.1, choose Access Point Mode and click Next on Working Mode in Figure 3.1.
Figure 3.1 Working Mode page
4. Wireless Setting page will appear as shown in Figure 4.1. Enter Wireless Network Name and AP Wireless Password, then click Next.
Figure 4.1 Working Mode page
• Wireless Network Name (SSID) - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXX (XXXX indicates the last unique four numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test.
• Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
• AP Wireless Password - Input the password of your broadcast SSID.
The company reserves the right to make changes of technical data without prior notice26
5. You can configure the IP parameters of LAN on this page. If you are not familiar with the settings on this page, it’s strongly recommended to keep the provided de-fault values, otherwise wireless network performance may be poor. After this click the button Next, Figure 5.1.
Figure 5.1 Quick Setup – Network Settings
Type - Choose SmartDHCP to get IP address from remoter DHCP server, or choose static IP to configure IP address manually.• IP Address - Enter the IP address of your system in dotted-decimal notation (factory
default: 192.168.0.254).• Subnet Mask - An address code that determines the size of the network. Normally
255.255.255.0 is used as the subnet mask.
The company reserves the right to make changes of technical data without prior notice 27
6. Click the Next button in Figure 5.1. You will then see the Finish page.
Figure 6.1 Quick Setup - Finish
7. Click button Reboot (Figure 6.1) to reboot the router. After reboot connect LAN/WAN port of TL-WR802N (A in Figure 7.1) to the wired network port with an Eth-ernet cable to MB-GATEWAY (B in Figure 7.1) and connect MB-GATEWAY to the ventilation system (C in Figure 7.1).
Figure 7.1 Hardware Installation of the TL-WR802N and MB-GATEWAY in AP Mode
MB-GATEWAY
TP-LINK routerMB-Gateway
TL-WR802N�sWi-Fi name:
TP-LINK_XXXX
B
A
C
The company reserves the right to make changes of technical data without prior notice28
8. Select new access point.
LAPTOPS
Click the icon at the bottom of your desktop. Click refresh button, and then select SSID of the Router figure 8.1, which you write in Wireless Network name (SSID) field in figure 4.1 or select root router. Click Connect.
Figure 9.1 Wi-Fi connection
Enter the Security key in the field Root AP Wireless Password. Figure 5.1. Click Next.
Figure 9.2 Security key window
The company reserves the right to make changes of technical data without prior notice 29
MOBILE PHONES, TABLETS
Go to Wi-Fi settings. Click button Scan and then select SSID of the Router, which you enter in the field Wireless Network name (SSID). Figure 4.1.
Figure 9.3 Wi-Fi connection
Enter the Security key in the field AP Wireless Password. Figure 4.1. Click Connect. Figure 9.4.
Figure 9.4 Security key window
9. To access MB-GATEWAY, open a web-browser (Google Chrome is recommend-ed) in address field type the MB-GATEWAY device name (hostname). According to the factory settings (default) MB-GATEWAY device name MBGW - plus the last six MAC address characters, for example., mbgw900154. In the page enter the login data: according to the preset parameters (default) username: admin pass-word: admin.
The company reserves the right to make changes of technical data without prior notice30
10. Control MB-GATEWAY via SALDA AIR android application.
Figure 10-1 Google play store application
In search results list find SALDA AIR application. Click the application. Figure 10.2
Figure 10.2 SALDA AIR application
Install SALDA AIR to mobile phone
First go to Google play store in search input write SALDA AIR.
The company reserves the right to make changes of technical data without prior notice 31
Click the button INSTALL. Figure 10.3.
Figure 10.3 Install SALDA AIR application window.
In the window that appears click ACCEPT and application SALDA AIR will be installed. Figure 10.4
Figure 10.4 Install SALDA AIR application window
The company reserves the right to make changes of technical data without prior notice32
11. Start AIR SALDA.
Figure 11.1 Security key window
Enter the Security key in the field AP Wireless Password. Figure 4.1. Click Connect. Figure 11.2.
Figure 11.2 Security key window
Go to Wi-Fi settings. Click button scan and then select SSID of the Router. Figure 11.1. Enter it in the field Wireless Network name (SSID). Figure 4.1.
The company reserves the right to make changes of technical data without prior notice 33
Start SALDA AIR application for Android devices and CONNECTING window will ap-pear. Figure 11.3.
Figure 11.3 Connecting window
In the window CONNECTING click the button AUTODISCOVER. Figure 10.7. SALDA AIR will find MB-GATEWAY as in shown Figure 11.4.
Figure 11.4 Autodiscover
Figure 11.5 SALDA AIR
After this you can controll MB-Gateway via SALDA AIR. Figure 11.5.
The company reserves the right to make changes of technical data without prior notice34
12. Control MB-GATEWAY via SALDA AIR IOS application.
Install SALDA AIR to mobile phoneFirst go to App store in search input write SALDA AIR.
Figure 12.1 App store
The company reserves the right to make changes of technical data without prior notice 35
In search list find SALDA AIR application. Click GET 12.2
Figure 12.2 SALDA AIR application
Click INSTALL button in figure 12.3.
Figure 12.3 Install SALDA AIR application window.
The company reserves the right to make changes of technical data without prior notice36
13. Start AIR SALDA on IOS
Go to wifi settings. Click scan button and then select SSID of the Router figure 13.1, which you write in Wireless Network name (SSID) field in figure 4.1.
Figure 13.1 Security key window
The company reserves the right to make changes of technical data without prior notice 37
Enter the Security key, wich you write in Root AP Wireless Password field in figure 4.1. Click Connect figure 13.2.
Figure 13.2 Security key window
Start SALDA AIR on iOS and CONNECTING window will appear, as shown in Figure 13.3.
Figure 13.3 Connecting window
The company reserves the right to make changes of technical data without prior notice38
In the CONNECTING window click the button AUTODISCOVER. Figure 10.7. SALDA AIR will find MB-GATEWAY as shown in Figure 13.4.
Figure 13.4 Autodiscover
Figure 13.5 SALDA AIR
After this you can controll MB-Gateway via SALDA AIR in figure 13.5.
Improvements and changes to this manual necessitated by typographical errors, inac-curacies of current information, or improvements to programs and/or equipment, may be made by the manufacturer at any time and without notice. Such changes will, however, be incorporated into new editions of this manual. All illustrations are for illustrative pur-poses only and may not accurately depict the actual device.
Full 300Mbps Wireless N Nano Router TL-WR802N specification you may find at http://www.tp-link.com.
MB-Gateway quick launch guide is located at www.salda.lt or directly http://www.salda.lt/en/products/item/mb-gateway.
Mobile application for Android is located at https://play.google.com/. Direct link: https://play.google.com/store/apps/details?id=lt.salda.air&hl=en.
Mobile application for iOS is located at https://www.apple.com/itunes/. Direct link: https://itunes.apple.com/us/developer/salda-uab/id1226456172
