aii33093 2007 pilot xm radio system (ex) · illustration of the xm satellite radio installed on the...
TRANSCRIPT
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 1 of 12
INSTALLATIONINSTRUCTIONS
Accessory Application Publications No.
Issue Date
08B15-S9V-1A00-91
PARTS LIST
XM Radio Attachment (sold separately)P/N 08B15-S9V-100A
2 Tuner brackets
4 Flange bolts, 6 x 12 mm
2 Cushion tapes
BUS cable
4 Washer-screws, 5 x 8 mm
EPT sealer(not used)
18 Wire ties
Wire tie with clip
Pillar clip
AUG 20062007 PILOTXM SATELLITE RADIO SYSTEM
(EX)
XM Antenna (sold separately)P/N 08A15-0J1-100
Antenna
All 33093
XM Unit (sold separately)P/N 08A15-3J1-000
XM tuner
2 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
TOOL AND SUPPLIES REQUIRED#2 Phillips screwdriverFlat-tip screwdriverUtility knifeTape measureShop towelScissorsRatchet10 mm and 14 mm Socket10 mm and 14 mm Combination wrenchesFelt-tip penIsopropyl alcohol(Isopropyl alcohol, in a 60/40 solution with water)T25 TORX bit
Illustration of the XM Satellite Radio Installed onthe Vehicle
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.
2. Disconnect the negative cable from the battery.
3. Remove the cap from the right sun visor (fourretaining tabs).
ANTENNACONNECTOR
RIGHT SUNVISOR
TORX SCREW
CAP
RETAININGTABS (4)
4. Remove the right sunvisor (two TORX screws andunplug the connector).
AUDIOUNIT
BUSCABLE
ANTENNAHARNESS
XM TUNER
5412070B
6512010Y
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 3 of 12
DOORWEATHERSTRIP(Remove.)
CLIP
RIGHT FRONTPILLAR TRIM
GLOVE BOX
STOPS (2)
(Lowercompletely.)
5. Remove two caps from the right front grab rail andremove the grab rail (two screws).
7. Remove the door weatherstrip from the openingedge of the right front door in the area shown,then remove the right front pillar trim (one clip).
8. Lower the glove box by removing the right and leftstops.
COVER
BOLT
COVER
RIGHT FRONTPILLAR
RIGHT FRONTPILLAR TRIM
CLIP
PIN
CLIP
PART MARKED WITH“SIDE CURTAIN AIRBAG”
Strike.
SHOPTOWEL
RUBBERMALLET
6. Pull away the door weatherstrip from around theright front pillar trim. Using a small rubber mallet,and a shop towel, gently tap the right quarterpillar trim at the area marked “SIDE CURTAINAIRBAG” to release the clip.
DOORWEATHERSTRIP
4N23033B
4N23041B
5412080B
4N23060B
4 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AUDIO UNIT
VEHICLECONNECTOR
SCREW(Reuse.)
VEHICLEANTENNACONNECTOR
12. Remove the audio unit (four screws), pull the audiounit out toward you, unplug the vehicle connectorsand vehicle antenna connector.
METER PANEL
SELF-TAPPINGSCREW
CLIPS (2)
9. Remove the meter panel (two self-tapping screwsand two clips).
METER SUBPANEL
CLIPS (3)
10. Remove the meter sub panel (three clips).
VEHICLECONNECTOR
CLIPS (5)
AUDIO PANEL
11. Gently pull out on the left side of the audio panelto release the two clips, then pull out to releasethe remaining three clips. Unplug the vehicleconnectors and remove the audio panel.
5412041B
4N23071B
5601020Y4N23080B
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 5 of 12
DRIVER’S CENTERCONSOLE TRIM
PASSENGER’S CENTERCONSOLE TRIM
CLIPS (3)RIGHTVEHICLEBRACKET
SCREW
HEATERCONTROL UNIT
LEFTVEHICLEBRACKET
SELF-TAPPINGSCREW
CENTER PANEL
CLIPS(2)
VEHICLECONNECTOR
VEHICLE 30-PINCONNECTOR
VEHICLE 20-PINCONNECTOR
With Player
• Remove the driver’s and passenger’s centerconsole trim pieces (three clips each). Takecare not to damage the clips.
• Remove four self-tapping screws that fasten thecenter panel.
• Pull the center panel out toward you to releasethe two clips. Unplug the vehicle connectorfrom the accessory socket, and remove thecenter panel.
• Remove four screws that fasten the left andright vehicle brackets. Pull the heater controlunit and pocket out toward you, and unplug thevehicle connectors.
13. Remove the driver’s seat front cover from thedriver’s seat (four clips).
CLIPS (4)
DRIVER’S SEATFRONT COVER
DRIVER’SSEAT
4N23100B
6 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
ADHESIVEBACKING
5 mm
30 mm
ATTACHAREA
HEADLINER
ATTACHAREA
FRONTWINDOW
ANTENNA
HEADLINER
17. Using isopropyl alcohol, clean the windshieldwhere the antenna will attach. Remove theadhesive backings from the antenna and attachthe antenna to the front window at the locationshown. Install the antenna by applying sufficientpressure.
DRIVER’S SEATREAR COVER
CLIPS (4)
DRIVER’S SEAT
DRIVER’S SEAT
BOLTS (4)
14. Remove the driver’s seat rear cover from thedriver’s seat. Take care not to damage the clips.
15. Remove the four bolts that secure the driver’s seatside rails to the floor.
16. Remove the driver’s center console lower cover(seven clips). Take care not to damage the clips.
CLIPS (7)DRIVER’S CENTERCONSOLE LOWERCOVER
DRIVER’SSEAT
4N23110B
4N23120B
4N23090B
4N24010B
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 7 of 12
GLOVE BOXOPENING
ANTENNAHARNESS
VEHICLEHARNESS
WIRE TIES (4)
VEHICLEHARNESS
ANTENNAHARNESS
VEHICLEHARNESS
WIRE TIEAUDIO UNITOPENING
19. Route the antenna harness through the glove boxopening and route it along the vehicle harness.Secure the antenna harness to the vehicleharness with four wire ties.
20. Route the antenna harness to the audio unitopening and secure it to the vehicle harness withone wire tie.
RIGHT FRONTPILLAR
RIGHT FRONTPILLAR TRIMOPENING
ANTENNA
ANTENNAHARNESS
VEHICLEHARNESS
VEHICLECLIPS (4)
WIRE TIES (5)
HEADLINER
18. Route the antenna harness along the right frontpillar and through the right front pillar trimopening. Secure the antenna harness to thevehicle harness with five wire ties.
ANTENNAHARNESS
BUSCABLE
AUDIO UNITOPENING
BUS CABLE14-PINCONNECTOR VEHICLE 20-PIN
CONNECTOR
WIRETIE
VEHICLEHARNESS
21. Continue routing the antenna harness and one endof the BUS cable through the radio opening anddown along the vehicle harness. Align the otherend of the BUS cable with the vehicle 20-pinconnector. Then secure the antenna harness andBUS cable to the vehicle harness with one wiretie.
4N24021B
4N24030B
4N24040B
4N24050B
8 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
DRIVER’S CENTERCONSOLE LOWERCOVER OPENING
BUSCABLE
ANTENNAHARNESS
VEHICLEHARNESS
VEHICLEFRAME
BUSCABLE ANTENNA
HARNESS
WIRETIE
VEHICLEHARNESS
WIRETIE
22. Route the antenna harness and BUS cable alongthe vehicle harness toward the floor, of the lowercenter console, and pull them out from under thedriver’s center console lower cover.
23. Secure the antenna harness and BUS cable to thevehicle harness and to the vehicle frame with twowire ties.
LOWERCENTERCONSOLE
With Player
• Bundle the BUS cable with one wire tie asshown.
• Route the antenna harness along the vehicleframe .
• Pull the BUS cable out 100 mm from thevehicle wire tie through the heater control unitopening.
• Secure the BUS cable to the vehicle harnessusing one wire tie.
WIRETIE
VEHICLEFRAME
ANTENNAHARNESS
BUSCABLE
WIRETIE
BUSCABLE
150 mm
100 mm
VEHICLEHARNESS
100 mm
VEHICLEWIRE TIE
HEATERCONTROL UNITOPENING
5725110Y
5725100Y
4N25010B
4N25021B
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 9 of 12
• Secure the antenna harness and BUS cable tothe vehicle frame with three ties in the areas.
• Connect the bus cable 14-pin connector to theplayer.
Cassette Player
MP3 Player
VEHICLEFRAME
WIRETIE
BUSCABLE
ANTENNAHARNESS
HEATERCONTROLUNIT
BUSCABLE
BUSCABLE 14-PINCONNECTOR
CASSETTEPLAYER
BUSCABLE 14-PINCONNECTOR
BUSCABLE
HEATERCONTROLUNIT
MP3PLAYER
RIGHTPLAYERBRACKET
SCREW(reused.)
HEATERCONTROLUNIT
LEFTPLAYERBRACKET
BUSCABLE
VEHICLE 30-PINCONNECTOR
WASHER-SCREW(reused.)
WASHER-SCREW(reused.)
VEHICLE 20-PINCONNECTOR
• Remove the two washer-screws from thedashboard.
5725130Y
5725140Y
5725120Y
5426161Y
10 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
VEHICLEHARNESS
FLOOR CARPET
Slit
50 mm
FLOORCARPET
BUSCABLE
ANTENNAHARNESS
27. Measure and slit the driver’s floor carpet areashown. Route the antenna harness and BUS cableunder the floor carpet and out through the slit.Take care not damage to the antenna harness andBUS cable when cutting the floor mat.
VEHICLEFRAME
CUSHION TAPE(Cut in half.)
VEHICLEHARNESS
VEHICLEFRAME
BUSCABLE
ANTENNAHARNESS
26. Using isopropyl alcohol on a shop towel, clean thevehicle frame where the cushion tapes will attach.Cut a cushion tape in half and attach the twohalves of the cushion tape to the vehicle framecleaned with isopropyl alcohol.
AUDIO UNIT
SCREW(Reuse.)
25. Reinstall the audio unit with four screws (youremoved).
AUDIOUNIT AUDIO UNIT
OPENING
BUS CABLE14-PINCONNECTOR
VEHICLECONNECTOR
VEHICLEANTENNACONNECTOR
24. Plug the BUS cable 14-pin connector, vehicleconnectors and vehicle antenna connector intothe audio unit, then carefully slide the audio unitinto the audio unit opening.
CUSHION TAPE(Clean withisopropyl alcohol(in a 60/40 solutionwith water)
4N25040B
4N25051B4N25030B
4N25061B
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 11 of 12
6512031Y
6512050Y
6512040Y6512020Y
TUNERBRACKET
5 x 8 mmWASHER-SCREWXM TUNER
28. Attach the tuner brackets to the XM tuner with four5 x 8 mm washer screws.
29. Using isopropyl alcohol, clean the area where thecushion tape will attach. Attach the cushion tapeto the tuner bracket at the location shown.
6 x 12 mmFLANGEBOLTS (4)
DRIVER’SSEAT
SEAT RAIL
TUNERBRACKET
TUNERBRACKET
XM TUNER
5 x 8 mmWASHER-SCREW
18 mm
FRONT
TUNERBRACKETcenter.
CUSHION TAPE
30. Install the tuner bracket to the driver’s seat railswith the four 6 x 12 mm flange bolts. Tighten thebolts securely.
XM TUNER
FRONTTUNERBRACKET
WIRE TIEWITH CLIP
BUSCABLE
FRONT
XM TUNER
BUS CABLE14-PINCONNECTOR
ANTENNACONNECTOR
31. Plug the BUS cable 14-pin connector into the XMtuner 14-pin connector.
32. Plug the antenna connector into the XM tunerantenna connector.
33. Secure the BUS cable and the antenna harness tothe tuner bracket with one wire tie with clip.
34. Secure the BUS cable and the antenna harnesswith one tie wire.
XM TUNER 14-PINCONNECTOR
XM TUNERANTENNACONNECTOR
ANTENNAHARNESS
WIRETIE
BUSCABLE
ANTENNAHARNESS
12 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
4N23050B
41. To install the pillar clip, position it at right anglesto the right front pillar and install by lightlypushing on the area marked with “SIDECURTAIN AIRBAG” on the right front pillar trim.Check that the pillar clip is not interfering with theairbag. Take care not to push the right front pillartrim excessively.
42. Reinstall all removed parts.
43. Reconnect the negative cable to the battery.
44. Enter the customer’s radio anti-theft code, andreset the radio station presets.
45. Reset the clock.
NOTE: Whenever the battery is disconnected, thedriver’s AUTO function is disabled.
46. Start the engine. Push down on the driver’swindow switch until the window is fully open.
47. Pull up on the driver’s window switch to close thewindow completely, then hold the switch for asecond or 2 more.
48. Test the AUTO window function.
RIGHT FRONTPILLAR TRIM
NEWPILLARCLIP
CLIP(Discard.)
RIGHT FRONTPILLAR TRIM
35. Bundle the excess of the antenna harness.Secure the antenna harness to the vehicle’sharness using two wire ties.
ANTENNA HARNESS(Bundle the excess)
36. Bundle the excess of the BUS cable. Secure theBUS cable and the antenna harness to thevehicle’s harness.
5610010P
BUS CABLE(Bundle theexcess.)
WIRETIE
WIRETIE
37. Check that all wire harnesses are routed properlyand all connectors are plugged in.
38. Reinstall the driver’s center console lower cover.
39. Reinstall the driver’s seat. Take care not to pinchthe any wires. Torque the seat bolts to 47 N·m(35 lb·ft).
40. Remove the clip from the top of the right frontpillar trim, and install a new pillar clip.