adult supervision required. binoculars · 2020. 1. 31. · you can’t use your binoculars if you...

Assembly: Start with sanding each wood piece to remove any rough edges. Remember to sand in the direction of the wood grain. Glue and nail the pieces together. Allow glue to completely dry. Contents: Made in Thailand exclusively for The Home Depot by Houseworks, Ltd. 2388 Pleasantdale Road, Atlanta, GA 30340 • 71130 • Thailand 1119 BINOCULARS 1 Finished example. 3 (Ver el dorso para instrucciones en español.) TSCA TITLE VI Compliant • Fine Sandpaper • Wood Glue • Hammer • #2 Phillips Screwdriver ALSO NEEDED: 4 18 Nails 4 Screws 2 Step 1—Lay the back piece flat with the screw holes on top. Place the small lens on top. Place one of the lens protectors on top. Align with 2 center holes. Using a #2 Phillips Screwdriver, carefully attach them together with 2 screws. Step 2—Lay the front piece flat with the screw holes on top. Pick up the big lens and feel both sides. One side is flat and the other side has curves. Make sure the curved side is facing down, place the big lens on the front piece. Place the other lens protector on top. Align with 2 center holes. Carefully attach them together with 2 screws. Step 3—Stand both front and back pieces up with the lens sides facing in. Place one of the side pieces on top. Make sure all edges are even. Nail them together with 4 nails. Turn the project over and repeat to attach the other side piece. Step 4—Lay the project down. Place the top piece on top. Make sure all edges are even. Nail it in place with 4 nails. Turn the project over. Place the bottom piece on top. Make sure the tabs are close to the back piece. Make sure front corners and back edges are even. Nail it in place with 6 nails. Attention: If you are painting the project, BE VERY CAREFUL not to paint inside the lens holes. You CAN’T use your Binoculars if you have paint on the lenses. Allow the paint to dry completely before adding the string and stickers. side view 1 Back 1 Front 2 Sides 1 Top 1 Bottom 2 Lens Protectors 1 Big Lens 1 Small Lens 1 Piece of String 1 Sticker Sheet WARNING: CHOKING HAZARD Toy contains small parts and functional/sharp points. Not for children under 3 years old. Adult supervision required. front piece back piece

Upload: others

Post on 12-Sep-2020

1 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: Adult supervision required. BinoCulARS · 2020. 1. 31. · You CAN’T use your Binoculars if you have paint on the lenses. Allow the paint to dry completely before adding the string

Assembly: Start with sanding each wood piece to remove any rough edges. Remember to sand in the direction of the wood grain. Glue and nail the pieces together. Allow glue to completely dry.

Contents:

Made in Thailand exclusively for The Home Depot by Houseworks, Ltd.2388 Pleasantdale Road, Atlanta, GA 30340 • 71130 • Thailand 1119

BinoCulARS

Finished example.

(Ver el dorso para instrucciones en español.)TSCA TITLE VI Compliant

•Fine Sandpaper

•Wood Glue

•Hammer

•#2PhillipsScrewdriver

Also Needed:

18 nails4 Screws

Step 1—Lay the back piece flat with the screw holes on top. Place the small lens on top. Place one of the lens protectors on top. Align with 2 center holes. Using a #2 Phillips Screwdriver, carefully attach them together with 2 screws.

Step 2—Lay the front piece flat with the screw holes on top. Pick up the big lens and feel both sides. One side is flat and the other side has curves. Make sure the curved side is facing down, place the big lens on the front piece. Place the other lens protector on top. Align with 2 center holes. Carefully attach them together with 2 screws.

Step 3—Stand both front and back pieces up with the lens sides facing in. Place one of the side pieces on top. Make sure all edges are even. Nail them together with 4 nails.

Turn the project over and repeat to attach the other side piece.

Step 4—Lay the project down. Place the top piece on top. Make sure all edges are even. Nail it in place with 4 nails.

Turn the project over. Place the bottom piece on top. Make sure the tabs are close to the back piece. Make sure front corners and back edges are even. Nail it in place with 6 nails.

Attention: If you are painting the project, Be VeRY CAReFUl not to paint inside the lens holes. You CAN’T use your Binoculars if you have paint on the lenses. Allow the paint to dry completely before adding the string and stickers.

side view

1 Back 1 Front

2Sides

1 Top

1 Bottom

2LensProtectors

1 Big lens1 Small lens

1Pieceof String

1 Sticker Sheet

WARNING: ChokING hAzARd Toy contains small parts and functional/sharp points. Not for children under 3 years old. Adult supervision required.

front piece

back piece